GTD33GASK - Webcollage.net
GTD33GASK
GE Appliances 7.2 Cu. Ft. Capacity Aluminized
Alloy Drum Gas Dryer
22 1/2"
29 1/2"
27"
Power Cord 4 1/2"
26"
11 3/4"
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
EXHAUST OPTION: When viewed from the
front of the unit, exhaust 3-way via rear, left
and bottom. Dryer is shipped exhausted to
the rear. Alternate exhausting knockouts are
supplied.
44"
37 1/2"
GAS: An individual, properly-grounded
branch circuit, with a three-prong groundingtype receptacle, protected by a 15 or 20 amp
circuit breaker or a time-delay fuse is required.
8"
3 1/2"
GAS DRYER ELECTRIC RATING:
120V, 60Hz, 6A
GAS (BTU/HR): 22,000. Factory-equipped
for natural gas. Tested for LP gas. LP gas
supply requires a conversion kit. Check
installation instructions for correct kit and
have a qualified gas technician install a
conversion kit. See dryer ducting information
for proper installation.
NOTE: Dryer wall outlet must be located
within 36" of service cord entry and accessible
when dryer is mounted in position.
INSTALLATION INFORMATION:
For complete information, see installation
instructions packed with your dryer.
Side View
1 3/4"
5"
3 1/4"
Rear View
SPECIAL INSTALLATION REQUIREMENTS
ALCOVE OR CLOSET INSTALLATION:
- I f your dryer is approved for installation in an alcove or closet, it will be stated on a label on
the dryer back.
-T
he dryer MUST be exhausted to the outside.
-M
inimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side; 1" front, top and rear
-C
loset doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in.
of open area equally distributed. If this closet contains both a washer and a dryer, doors must
contain a minimum of 120 sq. in. of open area equally distributed.
- No
other fuel-burning appliance shall be installed in the same closet with a gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
-T
he dryer MUST be exhausted to the outdoors.
-T
he installation must conform with the local codes, or in the absence of local codes, with the
National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
MINIMUM CLEARANCES OTHER THAN ALCOVE OR CLOSET INSTALLATION:
-M
inimum clearances to combustible surfaces are: 0" both sides; 1" rear
DRYER EXHAUSTING INFORMATION­:
Use metal duct only, vertical and horizontal ducting.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 7/16
GE Dryer Vent
GTD33GASK
GE Appliances 7.2 Cu. Ft. Capacity Aluminized
Alloy Drum Gas Dryer
FOR COMPLETE INFORMATION, SEE INSTALLATION INSTRUCTIONS PACKED
WITH YOUR DRYER.
DUCTING MATERIALS:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust
duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can
be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer
to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal
(foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semirigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the
entire length of the transition duct. Please see installation instruction packed with your dryer
for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side
or bottom of dryer, add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated
is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct
length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard
or moisture could cause damage. Never terminate the exhaust into a common duct or plenum
with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
GE Dryer Vent
DRYER EXHAUSTING INFORMATION—
USE METAL DUCT ONLY VERTICAL AND
HORIZONTAL DUCTING
BEST PERFORMANCE
Maximum length
of 4" dia rigid
A 4
metal duct
B
Exhaust hood type
A
Number
A
B
of 90°
4"
2-1/2"
4
2-1/2
Domestic dryer
turns
opening opening
B models
0
120 ft.
90 ft.
1
100 ft.
75 ft.
2-1/2
Long Vent 6.1-7.4
cu. ft.
2
85 ft.
65 ft.
capacity electric & gas
3
70 ft.
55 ft.
(GTD33, GTD42, GTD45,
4
60 ft.
45 ft.
GTD65, GTX22, GTX33, GTX42
and GTX65)
5
55 ft.
35 ft.
A
For every extra 90° elbow, reduce the allowable vent system
length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
When calculating the total vent system length, you must add all
the straight portions and elbows of the system (including the
transition duct.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE
CALL 1-800-GE-CARES.
For answers to your Monogram, GE Café™ Series, GE Profile™ Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center® Service, 800.626.2000.
Specification Revised 7/16
GTD33GASK
GE Appliances 7.2 Cu. Ft. Capacity Aluminized
Alloy Drum Gas Dryer
FEATURES AND BENEFITS
Aluminized alloy drum – Improves energy efficiency and resists corrosion
3 heat selections – Offer a choice of drying temperatures for personalized
fabric care.
Up to 120 ft. venting capability – Provides flexible installation
Auto Dry – For clothes that come out feeling and looking great, this setting
monitors air temperature to set the optimal drying time
Rotary electromechanical controls – Make it simple to set cycles
Up-front lint filter – Makes cleaning out lint easy
Reverse-a-door – Door opening can be reversed to meet laundry room needs
Model GTD33GASKWW – White
GTX33EASKWW_GTX33GASKWW_GTX33GASKWW_GTD33GASKWW
Specification Revised 7/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement