vector seating system
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
epoxy
a
b
c
TOOLS NEEDED
ratchet
steel
wire brush
pencil
7/32" hex bit for
tamper-resistant
screws
1/4", 1/2" & 3/4" drill
bits for concrete
tape measure
hammer drill
epoxy gun
STEP BY STEP FOR VECTOR SEATING SYSTEM CONFIGURATIONS WITH A STANDALONE BENCH
Place bench, top down
Attach legs
Position standalone bench
• Securely place bench, top down, on top
of a padded surface.
• Position leg with edge of bench seat.
• Carefully turn bench right side up; use
padding where necessary.
Note: You will need to use a sturdy,
elevated surface when attaching legs to
a configuration with seat backs.
• Insert 3/8"-16 x 3/4" tamper-resistant
button head cap screw (b) into mounting
holes in bench and thread into holes
using provided 7/32" hex bit for tamperresistant screws.
• Repeat with all benches ensuring
that end/intermediate legs are used
appropriately.
• Position bench in desired location. Be
sure that the space allows enough room
for full configuration.
• For freestanding configurations skip to
step 11.
Note: Forms+Surfaces recommends
using a sturdy box (or something similar)
to help temporarily position add-on
benches.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 5 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM CONFIGURATIONS WITH A STANDALONE BENCH
Side view of surface mount plate
11 1/8"
1/8”
Top view
11 1/8"
1/8”
Mark surface mount location
Position surface mount plate
Drill holes
• Once module is in the desired location,
mark the ground along the inside of each
leg including the center notch, indicated by
the dashed line.
• Measure and mark 1 1/8" from surface
mount mark to find the surface mount
plate center line, indicated by the dashed
line.
• Use hammer drill to drill 4.5" deep x 3/4"
diameter anchor hole at each marked
location using a 3/4" drill bit suitable for
concrete drilling.
• Carefully move bench to the side once
mounting surface is marked.
• Position the surface mount plate by first
aligning the center notch with the center
notch line.
Note: Forms+Surfaces recommends
starting holes with 1/4" diameter drill
bit followed by 1/2" and finally 3/4" for
maximum accuracy.
Note: Forms+Surfaces recommends using
a sturdy box (or something similar) to help
position add-on benches for this step.
• Next, align the mounting holes and
positioning notches to the surface mount
plate center line.
• Mark the center of each mounting
hole. T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 5 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM CONFIGURATIONS WITH A STANDALONE BENCH
7
9
8
Fill holes & insert anchors
Attach surface mount plate
Fit module onto surface mount plate
• Use compressed air and steel wire brush
to clean each anchor hole in accordance
with epoxy instructions.
• Position surface mount plate so that
mounting holes line up with anchors.
• Lift module up and slide leg(s) onto
mounted surface mount plate(s).
• Insert 3/8"-16 x 1-1/2" tamper-resistant
button cap screws (c) into mounting
holes in surface mount plate.
• Use epoxy in epoxy gun to fill each
anchor hole 5/8 of the hole depth in
accordance with epoxy instructions
• Insert 3/8"-16 x 4-1/4" epoxy anchor
(a) into each anchor hole so anchor top
is flush with ground. Allow proper curing
time according to cure schedule on
epoxy instructions before moving on to
Step 8.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 5 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING SYSTEM CONFIGURATIONS WITH A STANDALONE BENCH
11
12
L-bracket fastener
L-bracket
Bench cross-section
Bench cross-section
Attach leg to surface mount plate
Place L-bracket fasteners
Attach L-bracket
• Ensure that leg mounting hole and
surface mount plate mounting hole align.
• Identify add-on attachment location on
receiving bench.
• Align L-bracket tabs with L-bracket
fastener mounting holes.
• Insert 3/8"-16 x 3/4" tamper-resistant
button head cap screw (b) into bench
connection holes using provided 7/32"
hex bit for tamper resistant screws.
• Place L-bracket fasters in the back of the
receiving bench’s side rail, approximately
11- 3/4" apart from eachother.
• Use 3/8"-16 x 3/4" tamper-resistant
button head cap screw (b) to secure
L-bracket to L-bracket fasteners using
a 7/32" hex bit for tamper-resistant
screws.
10
• Fit the fasteners horizonally and then turn
to sit vertically in the rail as shown above.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 4 of 5 | Rev. 06-18-15
VECTOR SEATING SYSTEM
INSTALLATION INSTRUCTIONS
STEP BY STEP FOR VECTOR SEATING CONFIGURATIONS WITH A STANDALONE BENCH
13
Attach add-on module
• Insert end tabs from add-on bench under
the receiving bench seat slats. Ensure
mounting holes from add-on bench line
up with L-bracket mounting holes.
• Once connection holes are aligned
insert 3/8"-16 x 3/4" tamper-resitant
button head cap screw (b) into bench
connection holes using provided 7/32"
hex bit for tamper resistant screws.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 5 of 5 | Rev. 06-18-15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement