Untitled - All
What's New In TB6AC+80W..............................................................................................................01
FOREWORD..........................................................................................................................02
Specfications........................................................................................................................03
Special features.....................................................................................................................03~04
Cyclic Chargring/Discharging...................................................................................................05
Lithium polymer balance charge program connection diagram.........................................................06
Warning and safety noets.........................................................................................................07~11
Program flow chart.................................................................................................................12~15
Select Languages...................................................................................................................15
Safe timer calculation..............................................................................................................15
Lithium(LiIo/liPo/LiFe)............................................................................................................15
Charging of lithium battery.......................................................................................................16
Charging lithium battery in the balance mode...............................................................................16
Individual cell connection diagram(pin-assignment of 8-pin).........................................................17
Fast charging of lithium battery..................................................................................................17
Storage control of lithium battery................................................................................................17
Discharging of lithium battery....................................................................................................18
Voltage balancing and monitoring in the discharge process...............................................................18
Charging/Discharging of NiCd/NiMH battery..................................................................................19
Pb battery program..................................................................................................................20~21
Data storage program...............................................................................................................22
Various information in the program..............................................................................................23~24
Extra function program..............................................................................................................25~30
Warning and error information....................................................................................................31
Warranty and service................................................................................................................32
What’s New In TB6AC+80W
Max charge current reach to 8A instead of 6A, that means it can speed up your charge by increasing the
charge current.
Max balance current increase to 460mA from 300mA, that means it can speed up your balance charge of
your lithium batteries.
15 extra functions provide more convenience for your hobby time.
1>LANGUAGES: There are two languages which you can select (English and Deutsch).
2>CELL METER: The charger can test the voltage of each cell of your batteries.
3> CAPACITY:Check the capacity of the battery.
4>IRThe battery pack measure internal resistance.
5>BALANCER: The charger can balance the voltage of each cell to preserve the performance your
batteries.
6> DIGITAL POWER:Using the charger's output as a DC power supply.
7>BRUSH MOTOR: You can easily break-in new bushed electric motor using a variable voltage and
running time.
8>FOAM HOT CUTTER: The charger acts as a convenient power supply for a hot wire foam cutter.
9>MOTOR/ESC/SERVO: The charger can output the PPM singal instead of your TX for your MOTRO/
ESC/SERVO, you can see the it's working status.
10>BRUSHLESS MOTOR: The charger can drive an inductance brushless motor.
11>SERVER TEST:The charger can test the server.
12> THRUST CALCULATOR:You can easily calculate the thrust of a propeller.
13>TEMP.:The charger can measure the external temperature by using a temperature sensor.
14>VOLTAGE METER:The charger can measure the DC voltage of an object.
15>PPM TEST:The charger can test the PPM signal from TX, so that you can check out some problem
bettween your TX and RX.
01
FOREWORD
Thank you purchasing the TB6AC+ 80W Balance charger.This product is a rapid charger with a high performance microprocessor and specialized operating software. Please read this entire operating manual
completely and attentively before using this product, as it covers a wide range of information on operating
and safety.Or please do use this product in company with a specialist!
Specifications
Operating voltage range:
DC11.0~18.0 Volt
Circuit power:
Max.charge power 80W[DC Input]
50W[AC Input]
Max.discharge power 5W
Charge current range:
Discharge current range:
Current drain for balancing Li-po:
NiCd/NiMH battery cell count:
Li-ion/Polymer cell count:
Pb battery voltage:
0.1~8.0A
0.1~1.0A
460mAh/cell
1~15 cell
1~6 series
2V~20V
AC to DC adaptor(DC11.0~18.0V)
Weight:
590g(Net Weight)
Dimensions:
135X145X43mm
02
SPECIAL FEATURES
Optimized operating software
TB6AC+80W features the so-called AUTO function t hat set the feeding current during the process of charging
or discharging. Especially for Lithium batteries, it can prevent the overcharging which may lead to an explosion
due to the user's fault. It can disconnect the circuit automatically and alarm once detecting any malfunction.
All the programs of this product were controlled through two way linkage and communication, to achieve the
maximum safety and minimized the trouble. All the settings can be configured by users!
Internal independent lithium battery balancer
TB6AC+80W employs an individual-cell-voltage balancer. It isn't necessary to connect an external balancer for
balance charging.
Balancing individual cells battery discharging
During the process of discharging,TB6AC+80W can monitor and balance each cell of the battery individually.
Error message will be indicated and the process will be ended automatically if the voltage of any single one cell
is abnormal.
Adaptable to various type of lithium battery
TB6AC+80W is adaptable to various types of Lithium batteries,such as Li-ion,LiPo and the new LiFe series of
batteries.
Fast and storage mode of lithium battery
Purposes to charge Lithium battery varies, " fast " charge reduce the duration of charging, whereas " store "
state can control the final voltage of your battery,so as to store for a long time and protect useful time of the
battery.
03
Maximum safety
Delta-peak sensitivity:The automatic charge termination program based on the principle of the
Delta-peak voltage detection. When the battery's voltage exceeds the threshold, the process
will be terminated automatically.
Automatic charging current limit
You can set up the upper limit of the charging current when charging your NiCd or NiMH battery;
It is useful for the NiMH battery of low impedance and capacity in the "AUTO" charging mode.
Capacity limit
The charging capacity is always calculated as the charging current multiplied by time. If the
charging capacity exceeds the limit, the process will be terminated automatically when you set
the maximum value.
Temperature threshold*
The battery's internal chemical reaction will cause the temperature of the battery to rise.If the
temperature limit is reached,the process will be terminated.
*This function is available by connecting optional temperature probe,which is not included in our
package.
Processing time limit:
You can also limit the maximum process time to avoid any possible defect.
Input power monitoring
To portect the car battery used as DC input power from being damaged,its voltage keeps being
monitored.If it drops below the lower limit,the process will be ended automatically.
Data store/load
The maximum five batteryies'data can be stored for users'convenience.You can keep the data
pertaining to program setting of the battery of continuous charging or discharging. Users can
call out these data at any time without any special program setting.
04
WARNING AND SAFETY NOTES
These warnings and safety notes are particularly important.Please follow the instructions for maximum
safety;otherwise the charger and the battery can be damagedor at worst it can cause a fire.
Never leave the charger unattended when it is connected to its power supply.If any malfunction
is found,TERMINATE THE PROCESS AT ONCE and refer to the operation manual.
Keep the charger well away from dust,damp,rain,heat,direct sunshine and vibration.Never drop
it.
The allowable input voltage is 11-18V DC
This charger and the battery should be put on a heat-resistant,noninflammable and nonconductive
surface.Never place them on a car seat,carpet or similar.Keep all the inflammable volatile materials
away from operating area.
Make sure you know the specifications of the battery to be charged or discharged to ensure it meets
the requirements of this charger. If the program is set up incorrectly,the battery and charger may be
damaged. It can cause fire or explosion due to over charging. This warranty is not valid for any
damage or subsequent damage arising as a result of a misuse or failure to observe the procedures
outlined in this manual.
07
NiCd / NiMH
Voltage level:1.2V/cell
Allowable fast charge current:1C-2C(depends on the performance of cell)
Discharge voltage cut off level:0.85V/cell(NiCd),1.0V/cell(NiMH)
Li-ion Voltage level:3.6V/cell
Max.charge voltage:4.1V/cell
Allowable fast charge current:1C or less
Min.discharge voltage cut off level:2.5V/cell or higher
LiPo Voltage level:3.7V/cell
Max.charge voltage:4.2V/cell
Allowable fast charge current:1C or less
Discharge voltage cut off level:3.0V/cell or higher
LiFe Voltage level:3.3V/cell
Max.charge voltage:3.6V/cell
Allowable fast charge current:4C or less
Discharge voltage cut off level:2.0V/cell or higher
Pb Voltage level:2.0V/cell
(Lead-acid)Max.charge voltage:2.46V/cell
Allowable fast charge current:0.4C or less
Discharge voltage cut off level:1.75V/cell or higher
08
To avoid short circuit between the charge lead always connect the charge cable to the charger first,
then connect the battery.Reverse the sequence when disconnecting.
Do not connect more than one battery pack to this charger at any one time.
Never attempt to charge or discharge the following types of batteries.
A battery pack which consists of different types of cells(including
different manufacturers)
A battery that is already fully charged or just slightly discharged.
Non-rechargeable batteries(Explosion hazard).
Batteries that require a different charge technique from NiCd,NiMh,
LiPo or Gel cell(Pb,Lead acid).
A faulty or damaged battery.
A battery fitted with an integral charge circuit or a protection circuit.
Batteries installed in a device or which are electrically linked to other
components.
Batteries that are not expressly stated by the manufacturer to be
suitable for the currents the charger delivers during the charge
process.
09
Please bear in mind the following points before commencing charging:
Did you select the appropriate program suitable for the type of battery you
are charging?
Did you set up adequate current for charging or discharging?
Have you checked the battery voltage?Lithium battery packs can be wired in
parallel and in series,i.e.a 2 cell pack can be 3.7V(in parallel)or 7.4V(in
series).
Have you checked that all connections are firm and secure?Make sure there
are no intermittent contacts at any point in the circuit.
Charging
During charge process,a specific quantity of electrical energy is fed into the
battery.The charge quantity is calculated by multiplying charge current by
charge time.The maximum permissible charge current varies depending on
the battery type or its performance,and can be found in the information by
the battery manufacturer.Only batteries that are expressly stated to be
capable of quick-charge are allowed to be charged at rates higher than the
standard charge current.
Connect the battery to the terminal of the charger:red is positive and black
is negative.Due to the difference between resistance of cable and connector,
the charger can not detect resistance of the battery pack,the essential
requirement for the charger to work properly is that the charge lead should
be of adequate conductor cross-section,and high quality connectors which
are normally gold-plated should be fitted to both ends.
10
Always refer to the manual by the battery manufacturer pertaining to charging methods,
recommended charging current and charging time.Especially,the Lithium battery should
be charged according the charging instruction provided by the manufacturer strictly.
Attention should be paid to the connection of Lithium battery especially.
Do not attempt to disassemble the battery pack arbitrarily.
Please get highlighted that Lithium battery packs can be wired in parallel and in series.
In the parallel connection,the battery's capacity is calculated by multiplying single
battery's capacity by the number of cells with total voltage stay the same.The voltage's
imbalance may cause fire or explosion.Lithium battery is recommended to charge in series.
Discharging
The main purpose of discharging is to clean residual capacity of the battery,or to reduce the
battery'voltage to a defined level.The same attention should be paid to the discharging process
as charging.The final discharge voltage should be set up correctly to avoid deep-dischargeing.
Lithium battery can not be discharged to lower than the minimum voltage,or it will cause a
rapid loss of capacity or a total failure.Generally,Lithium battery doesn't need to be discharged.
Please pay attention to the minimum voltage of Lithium battery to protect the battery.
Some rechargeable batteries have a memory effect.If they are partly used and recharged before
the whole charge is accomplished,they remember this and will only use that part of their
capacity next time.This is a "memory effect" it is said that NiCd and NiMH batteries are
suffering from memory effect.NiCd has more memory effect than NiMH.
Lithium batteries are recommended to be discharged partially rather than fully discharged.
Frequent full discharging should be avoided if possible.Instead,charge the battery more often
or use a battery of larger capacity.Full capacity cannot be used until it has been subjected to
10 or more charge cycles.The cyclic process or charge and discharge will optimize the
capacity of battery pack.
11
Program flow chart
As default this charger will be set to typical user
settings when it is connected to a 12V battery for
the first time.The screen displays the following
information in sequence and the user can change
the parameter on each screen.
If you need to alter the parameter value in the
program,press"Start/Enter"key to make it blink
then change the value with"INC"or "DEC"key.
The value will be stored by pressing"Start/Enter"
key once.
12
The screen shows the nominal voltage of Lithium battery.There are three
kinds of Lithium battery:LiFe(3.3V),LiIo(3.6V)or LiPo(3.7V).This information
is of critical importance that you have to check the battery carefully to make
sure it is set up correctly.If it is different from correct value,explosion can
occur during charge process.
To avoid from erroneous setting by users,TB6AC+80W detects the cell count of
Lithium battery automatically at the beginning of charge or dischargeprocess.
But battery that is deep-discharged can't be detected correctly.To avoid this
error,the time term can be set to verify the cell count by the processor.
Normaly,15 seconds are enough to detect the cell count correctly.You need
to extend the time term limit for the battery of large capacity.But the charge or
discharge process may come to an end within the time term because of the
time limit decided by the wrong count if you set too long time limit for the
battery of small capacity.This may cause fatal error.You have to extend the
time term if the processor detect the cell count incorrectly at the beginning of
charge or discharge process.Otherwise,default value is recommended to use.
The screen shows the сut-off temperature of Lithium battery.you can press
•
“DEC”or“INC”to
select the сut-off temperature(Temp.Rang:20~80℃).The
•
maximum temperature
of the battery can be set during the charge process.
The process will be terminated automatically to protect battery once the
temperature of battery reaches this value.This feature is accomplished
through temperature probe(optional).
13
- +
DEC INC
- +
DEC INC
DEC INC
- +
DEC INC
DEC INC
DEC INC
- +
DEC INC
- +
DEC INC
The battery becomes warm after cycles of charge/discharge process.The
program will insert a time delay after each charge/discharge process to
allow the battery enough time to cool down before beginning next cycle of
charge/discharge process.The valid value ranges from 1 to 60 minutes.
When the charge process starts,the integrated safety timer starts to run
simultaneously.If error detected or the termination circuit can not detect
whether the battery is fully charged or not,this unit is programmed to
prevent overcharging.Please refer to the below statement to calculate the
timer you set.
The program provides maximun capacity protection function.If the Deltapeak voltage can not be detected or the safety timer times out,the charge
process will stop automatically,when the battery reaches the user-set
maximum charge capacity.
DEC INC
The beep to confirm users'operation sounds every time a button is pressed.
The beep or melody sounds at various times during operation to confirm
different mode change.These functions can be switched on or off.
DEC INC
- +
DEC INC
This function monitors the voltage of the input battery used to power this
charger.If the voltage is lower than user-set value,the program will end
forcibly to protect the input battery.
- +
DEC INC
14
DEC
INC
In this program,here provide you two languages(English and Deutsch).
Press”Start/Enter” button again,and a beep will be sound,you can see the
“English” is flashing,at this moment,please press” DEC"or "Inc "to select
language.
The screen shows the language (Deutsch).
Safe timer Calculation
When charging NiCd or NiMH batteries , divide the capacity by current,then divide the result by 11.9, set this
number of minutes as the value for safety timer setting . If the charger stopped at this time threshold , about
140% of the capacity will have been fed into the battery.
For example:
Capacity
Current
Safety Time
2000mAh
2.0A
(2000/2.0=1000)/11.9=84 minutes
3300mAh
3.0A
(3300/3.0=1000)/11.9=92 minutes
1000mAh
1.2A
(1000/1.2=833)/11.9=70 minutes
Lithium (LiIo/LiPo/LiFe) program
The program is only suitable for charging/discharging Lithium-polymer batteries with a nominal voltage of 3.3/
3.6/3.7V / cell. Different batteries have different charge technique. There are two methods termed as constant
voltage and constant current. The charge current varies according to battery capacity and specification. The
final voltage is very important;it should precisely match the voltage of the battery:LiPo is 3.6V,LiIo is 4.1V,LiFe
is 3.6V.The current and voltage of the battery should be correctly set.
When you want to change the values of parameters,please press “Start/Enter” key to make it blink and then
use DEС or INC to change the value.Then press “Start/Enter” key again to store the value.
15
The left side of the first line shows the type of battery you choose. The value on the left
of the second line of the charger is current user set.After setting the current and voltage,
press”Start/Enter”key for more than 3 seconds to start the process.(charge current:0.18.0A,voltage:1-5V)
This displays the number of cells you set up and the processsor detects. "R" shows the
number of cells detected by the charger and "S "is the number of cells set by you at the
previous screen. If both numbers are identical you can start charging by press"Start/
Enter” button. If not,press ”Batt./stop” button to go back to previous screen to carefully
check the number of cells of the battery pack before going ahead.
This screen shows the real-time status during charge process. Press “Batt./Stop” key
once to stop the charge process.
This function is for balancing the voltage of Lithium-polymer battery cells while charging.In the balance
mode, the battery needs to have a balance lead to connect to the individual port at the right side of the
charger.And you need to connect the battery's output plug to the output of charger.
Charging in this mode is different from the normal modes,because the built-in processor monitors voltage
of individual cell and control input current fed into each cell to normalize the voltage.
The value on the left side of the second lines sets the charge current. The value on
the right side of the second lines sets the battery pack's voltage.After setting current
and voltage,press”Start/Enter” for more than 3 seconds to start the process.
This displays the number of cells you set up and the processsor detects. "R"shows
the number of cells detected by the charger and"S"is the number of cells set by you
at the previous screen.If both numbers are identical you can start charging by press
“Start/Enter” button.If not,press”Batt./Stop” button to go back to previous screen to
carefully check the number of cells of the battery pack before going ahead.
This screen shows the real-time status during charge process.Press”Batt./Stop”key
once to stop the charge process.
16
Charging current will become lower when it progress to the end of charging.
A specific CV process will be reduced to end the charging process earlier.In
fact,the charging current will goes to 1/5 when the charging process comes
to 1/10. Charging capacity will be a little smaller than normal charging, but
charging time will be shortened accordingly.
You can set up the charging current and voltage of the battery pack. Press
“Start/Enter” key to display voltage confirmation. Then press ”Start/Enter”
key again to confirm and begin to charge.
This screen shows the real-time status of"fast charging".Press “Batt.Type/
Stop” key once to stop the charge process.
This function is for charging/discharging batteries which are not used at once.This program is designed
for charging or discharging of batteries of specific original state.They are classified by types:3.75V LiIo,
3.85V LiPo and 3.3V LiFe.The program will begin to discharge if the original state of the battery exceeds
the voltage level of storage.
17
At this screen, you can set up the current and voltage of the battery pack.
Charging and discharging will make the batteries come to the voltage level
of"storage"state.
This screen shows the real-time status charging.Press”Batt. type/Stop”key
once to stop the charge process.
The value of discharge current on the left can not exceed 1C, and the value on
the right can not be under the voltage recommended by the manufacturer to
avoid deep discharging. Press ” Start/Enter” for more than 3 seconds to start
charging.
This shows the real-time status of discharging,you can press”Batt.Type/Stop”
key to stop discharging.
The processor monitors voltage of each cell when the battery packs are during its " storage " and
"discharging"process. To achieve this feature, plug each battery to the charger individually. If voltage of
any cell is abnormal,TB6AC+80W will show error message and terminate the program forcibly. So if there
is battery damage or disconnection,you can see the error message and press” INC?” to know which cell
is damaged.
The processor detects voltage of one cell is too low.
18
The 4th cell was damaged.The value of voltage may be zero if disconnection
occurs.
This program is for charging and discharging of NiCd/NiMH batteries associated
with R/C models applications.You can press”Start/Enter”key to make it blink and
then INC or DEC to change the parameter value.Press”Start/Enter” key to store
the value.
This program charge the battery using the current you set up.In the "auto" state,
you should set up the upper limit of the charge current to avoid damage by
excessive feeding current. Some batteries of low resistance and capacity can
lead to higher current in the"auto"charging mode. But in the manual mode, it will
charge with the current you set. You can make it blink in the current field and
press”INC?”or”?DEC” at the same time to switch mode.
The screen shows the real-time status.Press”Batt.type/Stop” key to end the program.The sound will emitted
to indicates the end of program.
Set charge current on the left and the final voltage on the right.Range of the
charge current is 0.1-2.0A;range of final voltage is 0.1-25.0V.Press”Start/
Enter”key for more than 3 seconds to start the program.
The screen indicates the discharging state.You can press ”Start/Enter” key to
alter discharge current. Press ” Start / Enter ” again to store the value. Press
”Batt.type/Stop”key to stop discharging.The emitted sound alerts the end of
discharging.
19
You can set up sequence on the left and the number of cycles on the right.You
can balance,refresh and bread-in the battery with this function.You can set a
temporary cool-off procedure in the use's setting.
Press”Batt.type/Stop”key to stop program,you can press ”Start/Enter” key to
alter charge current.The sound indicates the end of program.
When it approaches to the end,you can see the capacity of the battery being
charged or discharged.You can press”INC ”or” DEC”key to display result
of each cycle.
This program is only suitable for charging Pb (lead-acid) battery with nominal voltage from 2 to 20V. Pb
(lead-acid) battery is completely different from NiCd / NiMH battery. These batteries can only deliver
current lower in comparison to their capacity. The same restriction applies to the charging process.
Consequently, the optimum charge current can only be 1/10 of the capacity. Pb battery can not be used
for fast-charging, please follow the instructions provided by the battery manufacturer. You can press
“ Start / Enter ” key to make it blink and alter the value of parameters using ” INC ”or “ DEC”key, press
“Start/Enter” key to store the value.
20
Set up the charge current on the left and nominal voltage on the right.Range
of current is 0.1- 8.0A, the voltage should match the battery being charged.
Press”Start/Enter” key for more than 3 seconds to start charging.
The screen displays the real-time discharging status.Press”Start/Enter”key to
alter discharge current. Press ” Start/Enter ” key again to store the parameter
value you set. Press ”Batt.type/Stop”key to end the program.
Set up the charge current on the left and nominal voltage on the right. Range
of discharge current is 0.1 - 8.0A, the voltage should match the battery being
charged.Press”Start/Enter” key for more than 3 seconds to start charging.
The screen displays the real-time discharging status. Press “Start/Enter” key
to alter discharge current.Press”Start/Enter”key again to store the parameter
value you set.Press”Batt.type/Stop”key to end the program.
21
For your convenience,TB6AC+80W has a data storage function. It automatically stores the last 20 operation
data, so you can call back the data when charging or discharging without setting up the program again.
PROGRAM SELECT
Load Memory
Select "Load Memory" from the main menu, then press "START".
Press "INC" or "DEC" to cycle through the saved profiles.
There are memory slots 1 through 20, plus "LS", which automatically saves the last
charging/discharging profile used.
22
LiPo FAST CHARGE
4.6A 7.4V(2S)
Press "START/ENTER" to customize the saved profile. Here you can use
the "START/ENTER" key to rotate between different settings. Press "INC"/"DEC" to
change them, then press "START/ENTER" again to save.
R: 1SER S: 2SER
CONFIRM(ENTER)
Once the setup is complete, you can either press and hold "START/ENTER" to run
the profile, or you can simply press "STOP" to save the profile and exit.
you can inquire various information on the LCD screen during the charging and discharging process.Press
”DEC ”key,the charger will display user's setting.You can press” INC”key to monitor voltage of each cell
while the battery is connected with each port of the charger.
23
It comes to the final voltage when the program ended.
3-pin connector is selected to be the USB port.
The external temperature is displayed when the temperature probe is used.
Present input voltage.
The battery is connected with each port through cable;you can checkvoltage of
each cell in the battery pack. When the cable is connected with the ports on the
right of the charger, the program will display voltage of up to 6 batteries. The
battery pack needs an output connector connected with each cell.
24
Select Extern Function Program
In this program,you can select extern function of battery.
1>Measure Internal Resistance Program
In this program,the charger can ont only measure the internal resistance of the battery pack,and also can
measure the per-cell internal resistance(only available for lithium battery)
The battery pack start to measure internal resistance .
The two lines shows the first to the sixth cell’s internal resistance,which is only
available for the lithium battery. Press “DEC” or “Inc” to dispaly more imformation.
This screen dispalys the battery pack internal resistance.Press “DEC
dispaly the status information.
”or“
Inc” to
2>Check Capacity of battery
Start to check the capacity of lithium battery.
Press”Start/Enter”button again,and then press”DEC
battery type(LiPo/LiFe/LiIo).
”or“ Inc”,you can select
Please press”Start/Enter”button(>3 seconds),it display the stauts information of
the lithium battery.It indication of capacity is balancing of each cell in your battery
pack.
25
Press ”DEC
balanced.
”or“
Inc” button,it dispaly the capacity of your battery pack is
In this program,you can simply balance your 2-6S Lixx batteries using the integrated balancer.It indicates
voltage for each cell in your battery pack.
Press ”Start/Enter” button again,then press“DEC
your battery type(LiPo/LiFe/LiIo).
”or“
Inc” button,you can select
Please press ”Start/Enter”(>3 seconds) button again,it indication of voltage is
balancing of each cell in your battery pack.
The voltage of your battery pack is balanced.
26
4>Set up voltage and current of digital power
Using the charger's output as a DC power supply. Press “Start/Enter” again,a beep
will be sound, then you press “DEC ” or “ Inc” button to set up the voltage and
current of digital power.( Voltage range:5.0-25.0V, current range:0.1-10.0A)
Please press ”Start/Enter” button for more than 3 seconds, and this screen display
the currnet,voltage and test time of digital power .(Max. power: 80W)
You can easily break-in new bushed electric motor using a variable voltage and running time. With this function you
also check the motor performance to optimize your power-train.The break-in process is essential for maximizing the
power of a new brushed motor.New motors have square brushes which press up against the curved cpmmutator.The
goal for the break-in process is to gentle shape the brushed so that they develop a curved surface that fits snugly
against the commutator giving greater conducting surface area and hence lower losses and higher effciency.
The value in the right side of the first line sets the test duration in minutes.The second line
shows the upper limit of current on the left and drive voltage on the right.After setting the
current and voltage,Press”Start/Enter”for more than 3 seconds to start the new process.A
beep tone will sound.(Test time:1-90min,Current:0.1-20A,Test voltage:1-15)
27
Stauts display.The top line shows the drive current and voltage.The second line shows the
•
output capacity(mAh)
and in the lower right corner alternately displays the output power or
•
total run time.
• test at any time by pressing “Start/Enter”
You can stop the
•
6>Hot Wire Foam Cutter Drive
In this mode,the charger acts as a convenient power supply for a hot wire foam cutter.
•
•
The value on the right side of the first line sets the test duration in minutes.The second line
shows the upper
• limit of current on the left side and drive voltage on the right.After setting
the current and
• voltage press”Start/Enter”for more than 3 seconds to start the next
process.A beep tone will be sound.(Running time:0-90min,Current:0.1-20A,Voltage:1-40V)
Stauts display.The top line shows the foam cut current and voltage.The second line shows
• the lower right comer alternately displays the output power or tatal run
the status and in
•
time.
•
You can stop the
test at any time by pressing”Start/Enter”.
•
28
7> Check ESC/Motor PPM and BL Motor RPM
The TB6AC+80W incorporates,as the first charger,a fantastic feature which allows
you to check your brushless motors sensors and even measure motor RPM! In
combination with the built-in receiver simulator port you can even speed-controls
for correct function.The receiver simulator port also allows the check of servo’s.
Press”Start/Enter”button,then press" DEC"or"INC ".After setting the max.signal
and max.signal,press”Start/Enter”for more than 3 seconds to start the next process.
Min. Pules width (range:700~1500us) Max. Pules width (range:1500~2300us)
Status display.this screen check out the output signal and motor RPM
In this program, you can easily calculate the thrust of a propeller.
Press " DEC " or " INC " button, you can set up the RPM,the screen display the
thrust calculator and its power.After setting the RPM,please press”Start/Enter” for
more than 3 seconds to start the next process.
29
•
•
9>Measure External Temperature
In this program,
the charger can measure the external temperature by using a
•
temperature sensor.
•
A>Measure Input Voltage and Output Voltage
•
In this program,
the charger can measure the DC voltage of an object.
•
B>Measure TR/RX
•
In this program,
the charger can measure the signal between TR and RX.
•
30
Warning and error information
TB6AC+80W incorporates a variety of functions for the systems to verify processes and the state of the
electronics.In case of an error the screen will display the cause of error and emit an audible sound.
Incorrect polarity connected.
Battery connection is interrupted.
Short-circuit of the output termination.
Erroneous selection of voltage of Lithium pack,please check the voltage of the
battery pack.
The voltage of the battery pack has been selected incorrectly!
The charger has malfunctioned for some reason.Seek professional advice.
The voltage is lower than which is set.Please check the number of cells in the
battery pack.
The voltage is higher than which is set.Please check the number of cells in the
battery pack.
31
Voltage of one cell in the battery pack is too low,please check the voltage of each
cell.
Voltage of one cell in the battery pack is too high,please check the voltage of each
cell.
Wrong connection of the connector detected,please check the connector and cable.
The internal temperature is too high,please cool down.
The processor cannot control the feeding current,please repair it.
We guarantee this product to be free of manufacturing and assembly defects for a period of one year from
the time of purchase.The warranty only applies to material or operational defects,which are present at the
time of purchase. During that period, we will repair or replace free of service charge for products deemed
defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt) . This warranty is not valid for any
damage or subsequent damage arising as a result of misuse, modification or as a resuit of failure to
observe the procedures outlined in this manual.
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising