Unavngivet 1 - Batteri Online
EN - universal Battery Charger for HITACHI batteries
DO NOT CONTINUE to use a battery with low voltage or capacity. Immediately charge the battery.
1. Charger Specification
The seperate universal AC adaptor (power supply) can be used with world
wide AC voltage of 100 ̴ 240V, 50 ̴ 60Hz. It has an output of 36V DC 2A and
is plugged into the battery charger unit.
Battery Charger Output is 7.2V to 18V DC 1.5A and has an automatic
three stage mode of: Pre-charge, Constant charge and Trickle charge.
CHARGE TIMES:
Nickel Cadmium
Nickel Metal Hydride
Li-Ion
Capacity (Ah)
1.3
1.5
2.0
2.1
2.5
3.0
3.3
3.0
Time in Mins
52
60
80
84
100
120
132
120
Charging Temperature
Batteries should be cool before charging commences and the ambient temperature should be less than +40ºC (104ºF) and more than -10ºC (-14ºF).
Charging Protection
The charger has built-in circuit protection to prevent overheating, short circuits, extended time charging and detection of damaged batteries.
2. Charging Procedure
Always keep the charger battery cavity clear. DO NOT put any metal objects into battery cavity as it may short circuit the charger.
Always unplug the charger from the power supply or turn off the power supply when there is no battery pack in the cavity. Unplug the charger before
attempting to clean it.
To assist in the cooling of the battery pack after use, avoid placing the charger or battery pack in a warm environment such as in a metal shed, or an
un-insulated vehicle or trailer.
5. CAUTION
BATTERY CHARGER CAN CAUSE ELECTRIC SHOCK, SEVERE INJURY AND DEATH.
 Please read all instructions before using the charger.
 This charger is designed for indoor use only.
 Do not probe with conductive metal objects during charging.
 Do not insert a cracked or damaged battery into the charger.
1.Connect the power supply output plug to the input socket on the charger,
and then plug the other side cord into an appropriate AC wall socket.
Do not allow any liquid to get inside charger. Keep it away from water
and moisture.
2.Insert the battery pack into the charger, making sure the pack is fully
seated in the battery cavity. The red light will come on indicating the
charging process has started.
To reduce the risk of injury, charge only batteries designed for HITACHI
tools in this charger. Other types of batteries may burst, causing personal injury and damage.
3.The charger will show a blinking red light up to when the battery is
fully charged. If the battery is left in the charger after the battery is fully
charged it will automatically switch to Trickle charge mode.
Make sure the power supply cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to damage or stress.
4.After charging is complete unplug the charger from the power source.
3. Light Indicators
PACK CHARGING steady red light
FULLY CHARGED red light blinks at once per second
FAULTY BATTERY red and green light blink at once per second
SHORT CIRCUIT red light blinks at three times per second
TEMPERATURE DELAY red light blinks at three times per second
4. Charging Advice - IMPORTANT
To reduce the risk of damage to the electric plug and cord when disconnecting the charger from the wall socket, pull tby the plug rather than
the cord.
Use only the power supply supplied, to avoid any possible damage to
the charger.
THESE CHARGERS ARE CAREFULLY MANUFACTURED TO SUIT AND
REPLACE ORIGINAL BRAND CHARGERS. THEY MUST NOT BE CONSIDERED TO BE ORIGINAL EQUIPMENT MANUFACTURER’S SPARE
PARTS. ALL BRANDS AND TRADEMARKS ARE THE PROPERTY OF
THEIR RESPECTIVE OWNERS.
ALL CHARGERS HAVE A TWELVE MONTH WARRANTY FROM THE
DATE OF PURCHASE.
To obtain the best performance and lengthen the life of the battery pack
it should be charged correctly. DO NOT charge the battery pack in an air
temperature below +0ºC (32ºF), or above +40ºC (104ºF). This is important
and will prevent serious damage to the battery pack.
It is normal for the charger and battery pack to become warm to the touch
while charging. The battery pack should be recharged when it fails to
produce sufficient power to operate the tool - (when it losos its “grunt”).
For further information please contact:
www.japcell.eu
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement