advertisement
Embrace
™
35/Advanced
Rear-facing Child
Restraint System
Owner’s Manual
Keep for future use
Rear-facing*
1.8 to 15.8 kg
(4 to 35 lbs)
43 to 76 cm
(17 to 30 in.)
* See page 1 for complete requirements.
ARMPIT LEVEL
Para instrucciones en Español, llamar al: 1-800-233-5921
WARNING:
To reduce the risk of serious injury or death, read this owner’s manual prior to installing and using this child restraint.
© 2017 Evenflo Company, Inc. 25701369 3/17
More children are killed every year as passengers in car
crashes than by any other type of injury. To reduce the risk of SERIOUS INJURY or DEATH, read this owner’s manual and your vehicle owner’s manual before installing and using this child restraint. Using a child restraint makes a big difference. By properly using this child restraint and following these instructions (and the instructions that accompany your vehicle), you will greatly reduce the risk of serious injury or death to your child from a crash. Do not be misled by the commonly used term “safety seat”; no restraint system can prevent all injuries in all crashes. Many properly restrained adults and children are injured in motor vehicle crashes, including relatively minor crashes. A properly used child restraint is the best way to minimize injuries to your child and to increase the chances for your child’s survival in most crashes.
Table of Contents
Premature Infant Use ........................................................ 2
Warnings .......................................................................... 3
LATCH Warnings ............................................................... 7
Recall Information for U.S. Customers ............................... 9
Public Notice for Canadian Customers ............................ 10
Motor Vehicle/Airplane Usage ......................................... 10
Care and Cleaning .......................................................... 11
Storing Your Instructions ................................................. 11
Visual Glossary ................................................................ 12
Using the Embrace Handle .............................................. 16
Proper Installation WITH the Convenience Base
Installation Checklist .................................................... 19
Installing the Convenience Base with
the Lower Anchor Connector Assembly .................... 20
Installing the Convenience Base with
the Vehicle Seat Belt ................................................. 23
Placing the Carrier in the Base ..................................... 25
Releasing the Carrier from the Base .............................. 27
Proper Installation WITHOUT the Convenience Base
Installation Checklist .................................................... 29
Installing the Carrier without the Convenience Base .... 30
Securing the Child in the Carrier ..................................... 33
Removing the Child from the Carrier .............................. 35
Changing the Harness Position ....................................... 36
Changing the Crotch Strap Position ................................ 38
Removing the Lower Anchor Connector Assembly .......... 40
Using the Locking Clip .................................................... 41
General Information about SensorSafe™ ......................... 44
Using SensorSafe ............................................................ 46
Using as an Infant Carrier ................................................ 48
Securing Your Child Restraint in Aircraft .......................... 50
Installing Convenience Base in Aircraft ............................ 51
Installing Carrier without Convenience Base in Aircraft .... 54
Installing the Canopy ...................................................... 57
Installing the Accessories ................................................. 57
Replacement Parts .......................................................... 59
Limited Warranty ............................................................ 61
U.S. REGULATORY NOTICE
This child restraint meets all the requirements of
Federal Motor Vehicle Safety Standard 213.
CANADIAN REGULATORY NOTICE
(MODEL NUMBERS ENDING IN “C”)
This child restraint meets all the applicable requirements of Canadian Motor Vehicle Safety
Standard CMVSS 213.1.
CHILD REQUIREMENTS
Warning: Failure to follow these Child Requirements could result in serious injury or death.
This child restraint is designed for use by children in
rear-facing orientation only. To use this child restraint properly, children
MUST
meet the size and age requirements below. In addition, Evenflo recommends consulting with your child’s physician before allowing your child to transition from a
rear-facing to forward-facing child restraint.
The American Academy of Pediatrics (AAP) recommends keeping children rear-facing until 2 years old or until they reach the maximum height or weight for their child restraint in
rear-facing orientation. Additionally, some states’ laws require children to be rear-facing until age 2. Accordingly, you will see this guidance reflected in the Child Requirements below.
Please review any applicable local, state or provincial laws related to child passenger safety before installing and using this child restraint.
Rear-facing
• 1.8 to 15.8 kg (4 to 35 lbs)
• 43 to 76 cm (17 to 30 in.) and top of child’s head is at least 25 mm (1 in.) below the top of the child restraint seat back.
IMPORTANT: Once your child exceeds any of the size requirements above, they
MUST
discontinue use of this child restraint.
Symbol Legend
Airbag Symbol
– Alerts you to important information about airbag safety.
LATCH Symbol
– Alerts you to important information about LATCH safety.
Aircraft Symbol
– Alerts you to important information about aircraft safety.
1
PREMATURE INFANT USE
Before using this child restraint for preterm or low birth weight infants, ensure the Child Requirements are met and follow the guidelines in this section.
According to the U.S. National Highway Traffic Safety
Administration, a properly installed child restraint reduces the risk of death by over 70 percent for infants involved in crashes. Federal Motor Vehicle Safety
Standard (FMVSS) 213 establishes design and dynamic performance requirements for child restraint systems.
However, the standard has no minimum weight limit and does not address the special medical needs of preterm or low-birth weight infants. To ensure that preterm and low-birth weight infants are transported safely, the guidelines published by the American
Academy of Pediatrics (AAP) in Pediatrics 2009;
123:1424–1429 must be followed.
All children should ride rear-facing in the vehicle as long as possible. Preterm and low-birth weight infants are at additional risk of breathing difficulties and heart problems when placed in a child restraint. Evenflo requires that the evaluation recommended by the AAP be conducted for all infants born earlier than 37 weeks and all newborn infants who weigh less than 5 pounds at birth before their first car trip to check for breathing difficulties or heart rate problems when traveling in a rear-facing child restraint.
The AAP recommends that appropriate hospital staff observe your infant in the child restraint for a period of
90 to 120 minutes or the duration of travel, whichever is longer. This period of observation must be performed with the infant properly positioned as described in these instructions and with the child restraint placed at an angle that is approved for use in the vehicle. The hospital staff will check for any breathing difficulties or heart rate problems. Your child’s pediatrician will let you know if there are any special considerations for travel.
The number of trips and the duration of time the infant is seated in the child restraint should be minimized. A caregiver should ride in the back seat to monitor the infant during travel.
You can learn more about the AAP’s recommendations for observation of newborns and the guidelines for safe transportation of preterm and low-birth weight infants, as well as other resources for parents and medical professionals, at
https://www.healthychildren.org/english/safetyprevention/on-the-go/Pages/default.aspx
2
WARNING
General Warnings
• Failure to follow the Child Requirements for use of this child restraint could result in serious injury or death. (See page 1 for Child Requirements).
• This product contains magnets. Before use, consult your family doctor about the compatibility of this product with pacemakers and similar devices.
• Child Restraints should be used only for travel.
Potential adverse health effects from excessive use of infant child restraints have been documented.
You should limit the time spent each day in a child restraint as much as possible. You must never use your child restraint as a sleeping environment in the home. Never leave your infant unattended in a child restraint in or out of the vehicle.
• Failure to follow installation instructions and the instructions and warnings on the product can result in your child striking the vehicle’s interior during a sudden stop or crash. Serious injury or death may result. These instructions and the instructions in your vehicle owner’s manual must be followed carefully.
If there is a conflict between the two, the vehicle owner’s manual regarding child restraint installation must be followed.
• This child restraint
MUST ALWAYS
face the rear
of the vehicle. Serious injury or death can occur.
•
NEVER
leave child unattended.
•
DO NOT
use child restraint if it is damaged, broken, or missing parts.
•
DO NOT
use this restraint if it has been involved in a crash. It must be replaced.
• DO NOT attach additional padding, toys or other devices not made by Evenflo, or described in these instructions, to the child restraint. Items not tested with the child restraint could injure the child.
• Be sure that the handle is firmly locked in Position 2
(Carry) before lifting the child restraint (see pages
16-17).
• This child restraint must be securely belted to the vehicle at all times, even when unoccupied. An unsecured child restraint may injure someone if a crash occurs.
3
WARNING
Air Bag Warnings
•
DO NOT
use this restraint in the front seat of a vehicle equipped with an air bag. Interaction between a rear facing restraint and air bags may cause serious injury or death. If your vehicle has an air bag, refer to the vehicle owner’s manual for child restraint installation.
• If the rear seat of your vehicle is equipped with side air bags, refer to the following information for proper usage.
Vehicles built prior to the 2002 model year:
DO NOT
use this restraint in a vehicle seating position equipped with a side air bag unless authorized by the vehicle manufacturer.
Model year 2002 and newer vehicles:
Refer to your vehicle owner’s manual before placing this restraint in a seating position equipped with a side air bag.
•
DO NOT
place any objects between the restraint and the side air bag, as an expanding air bag may cause the items to strike your child.
The forward-facing rear seat is the safest place for children 12 and under.
4
WARNING
Location Warnings
•
ALWAYS
read and follow exactly the instructions that accompany your vehicle and child restraint.
• According to accident statistics, children are safer when properly restrained in a rear seating position than in a front seating position. Generally, the center rear is safest and should be used if available. Children
12 and under should ride in the back seat of the vehicle.
• If you are unable to use the center rear seating position and have to install this child restraint directly behind a front vehicle seat, ensure that there is at least 38 mm (1.5 inches) of space between any part of the child restraint and the vehicle seat that is closest to the child’s head. This space may be necessary for the child restraint to properly perform in certain types of crashes.
•
ONLY
use this child restraint on forward-facing vehicle seats.
DO NOT
use on vehicle seats which face the rear or side.
•
ONLY
use this child restraint on vehicle seats with backs that lock into place.
• Some child restraints do not fit all vehicles or all seating locations. There are thousands of combinations of vehicle makes, models, child restraint configurations, seat belt designs and seat cushion shapes. The easiest way to determine whether your child restraint is suitable for a particular seating position is to check for a tight installation. If the child restraint cannot be properly installed,
DO
NOT use this child restraint. Consult vehicle owner’s manual, try a different seating location or call
Evenflo at 1-800-233-5921 (U.S), or
1-937-773-3971 (Canada).
Vehicle Seat Belt Warnings
• DO NOT use this child restraint in a vehicle seating position with door-mounted seat belts.
•
DO NOT
use this child restraint in a vehicle seating position with seat belts that automatically move along the vehicle frame when the door is opened.
These seat belts will not hold a child restraint properly.
5
WARNING
Vehicle Seat Belt Warnings – cont.
•
DO NOT
use this child restraint in a vehicle equipped with seat belts that only lock during a sudden stop or crash (emergency locking retractor –
ELR). You must use a seating location with a locking seat belt. Check your vehicle owner’s manual to see if you have seat belts with ELR’s.
•
DO NOT
loosen the vehicle seat belt to provide more leg room as this may keep the child restraint from protecting your child.
• Fold-down armrests could pose a hazard to a rear-facing child in certain types of collisions. Consult your vehicle owner’s manual before installing any rear-facing child restraint in front of a fold-down armrest.
• The headrest on the vehicle seat that the child faces should be placed in the lowest position. The vehicle seat back that the child faces must be fully padded and free of any hard objects.
• DO NOT use this child restraint if it moves more than 25 mm (1 in.) side-to-side or front to back at the seat belt path. Serious injury or death may occur.
Try again or move the child restraint to another seating location.
• If the vehicle seat belts are not routed and fastened correctly, the child restraint may not protect your child in a crash.
• DO NOT allow the vehicle seat belt release button to touch the child restraint. Accidental contact may cause the seat belt to release. If necessary, turn the vehicle seat belt release button away from the child restraint or move the child restraint to a different location.
• Failure to adjust the harness snugly around your child may result in your child striking the vehicle’s interior during a sudden stop or crash. Serious injury or death may occur.
• Remove locking clip from vehicle seat belt when not used with a child restraint, or the vehicle seat belt will not properly restrain an adult or child. Serious injury or death may occur.
6
WARNING
LATCH Warnings
• The LATCH (Lower Anchors and Tethers for
CHildren) system is intended to be used
ONLY
as described in these instructions. Serious injury or death may result from misuse. LATCH is a system for attaching the child restraint to your vehicle seat.
It can be used in place of the seat belts in vehicles with vehicle lower anchor bars. Refer to your vehicle owner’s manual for the locations of the vehicle lower anchor bars. Note: Your vehicle owner’s manual may refer to this system as “Universal Anchorage System
(UAS),” “Lower Universal Anchorage System,” or
“ISOFIX.”
• In addition to these instructions, read and follow your vehicle owner’s manual regarding installation of the child restraint and LATCH. If there is a discrepancy, follow your vehicle owner’s manual.
•
ONLY
use for securing convenience base to vehicle lower anchor bars.
•
NEVER
attach two lower anchor assembly connectors to one vehicle lower anchor bar.
•
NEVER
use the vehicle seat belts when using the lower anchor connector assembly. Using both together can cause slack in a sudden stop or crash.
• When not in use, the lower anchor connector assembly should be securely stored in the storage area located in the convenience base. Keep out of reach of children.
•
ALWAYS
be sure that the lower anchor connector assembly connectors are fully engaged onto the vehicle anchor bars by pulling hard on the lower anchor connector assembly harness. If they are not totally engaged, the lower anchor connector assembly will not secure your child restraint. Serious injury or death may result.
• DO NOT use this child restraint if it moves more than 25 mm (1 in.) side-to-side or front to back at the vehicle belt path. Serious injury or death may result from poor installation. If you can not tightly secure the child restraint, try again or move it to another location.
7
WARNING
Usage Warnings
• Children have STRANGLED in loose or partially buckled harness straps. Fully restrain the child even when carrier is used outside the vehicle.
ARMPIT LEV
EL
ARMPIT LEV EL
WARNING
Children have STRANGLED in loose or partially buckled harness straps. Fully restrain the child even when carrier is used outside the vehicle.
• Use
ONLY
the Embrace 35 convenience base with the Embrace 35 carrier. The Embrace 35 carrier
WILL NOT LOCK
safely into any other convenience base and serious injury or death will result. Refer to page 13 to properly identify the Embrace 35 convenience base.
•
ALWAYS
check the restraint and buckle for hot surfaces before putting a child into the restraint.
Your child could be burned.
• In cold weather, DO NOT dress the child in bulky clothing, like snowsuits, if the child is riding in a child restraint. This clothing makes it difficult to properly tighten the harness to the child, which may allow the child to be ejected from the restraint during a crash.
•
ALWAYS
place the handle in one of the following positions when traveling in a vehicle:
U.S. - Position 1, 4 or 5; Canada -
ONLY
Position 1
(p. 16).
• When using this restraint in Position 5 (Stand)
(p. 16),
ONLY
use on level ground and
NEVER
prop the restraint up with any object.
• NEVER place this child restraint on beds, sofas, or other soft surfaces. The child restraint can roll over on soft surfaces and suffocate the child.
• NEVER place this child restraint near the edges of counter tops, tables, other high surfaces, or in shopping carts. The child’s movements can cause the child restraint to slide and fall.
8
WARNING
• The canopy is not intended to provide UV protection.
•
Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children.
If someone unbuckles, stop the vehicle. Being firm and consistent right from the start will mean fewer discipline problems as children get older. Besides, an unrestrained child or adult can be thrown into and injure other passengers.
•
NEVER
try to tend to a crying baby’s needs while driving. NEVER take a baby out of a child restraint for comforting while the vehicle is moving.
• Always place the handle in Position 4, or 5 before removing infant from carrier (p. 16).
•
DO NOT
allow a child to have objects such as lollipops or ice cream on a stick. The object can injure the child if the vehicle swerves or hits a bump.
•
DO NOT
feed an infant who is riding in a child restraint.
• Anything loose can be deadly in a crash. Put sharp or heavy items in the trunk.
• DO NOT dress the child in blanket sleepers or other clothing that would prevent the crotch strap from fitting snugly up against the child.
Recall Information for U.S. Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall. Send your name, address, e-mail address if available, and the restraint’s model number and manufacturing date to:
Evenflo Company, Inc.
1801 Commerce Dr.
Piqua, OH 45356 or call 1-800-233-5921. or register online at:
www.evenflo.com/registercarseat
• For recall information, call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236
(TTY:1-800-424-9153), or go to
http://www.NHTSA.gov
9
Public Notice for Canadian Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a public notice. Send your name, address, the restraint’s model number, and manufacturing date to
Evenflo Company, Inc.
1801 Commerce Dr.
Piqua, OH 45356 or call 1-937-773-3971 or register online at:
www.evenflo.com/registercarseatcanada
• For public notice information, call Transport Canada at
1-800-333-0510 or go to www.tc.gc.ca
Motor Vehicle/Aircraft Usage
When used with the internal harness and
properly installed pursuant to these instructions, this restraint is certified for use only in passenger and multi-purpose passenger motor vehicles, buses and trucks equipped with either lap belts only or lap/shoulder belt systems, and in aircraft.
T
IP
!
!
Check with your airline before departure to make sure this restraint meets their requirements.
Refer to pages 50 to 56 for complete instructions on installing your child restraint in aircraft.
Storing Your Instructions
Care and Cleaning
•
DO NOT
lubricate or immerse in water the LATCH connectors, the buckle, or any other part of this child restraint, unless rinsing is permitted, as stated on the back of the buckle for your restraint.
• Plastic and metal parts may be wiped clean with mild soap and water and dried with a soft cloth. Do not use abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and water. Allow harness to air dry.
• Machine wash the seat pad separately in cold water, delicate cycle. Tumble dry 10 to 15 minutes on low heat.
•
NEVER
use child restraint without the seat pad.
• To protect the child restraint from damage caused by weather, rodents, and other elements common to garages, the outdoors, and other storage locations, remove the seat pad and thoroughly clean the restraint and pad prior to storage. Take care to clean in the areas where crumbs and other debris tend to accumulate.
T
IP
!
!
To help protect the vehicle upholstery, place a towel beneath and behind the child restraint.
ARMPIT LEVEL
After thoroughly reading and following these instructions, store them in the carrier behind the seat pad, as shown.
For future reference, record the model number of your child restraint AND the date of manufacture below.
Model Number:
Date of Manufacture:
10 11
Visual Glossary
Your vehicle components may be significantly different than pictured.
Consult your vehicle owner’s manual to help you identify your vehicle components.
Back Seat
Fold-down Armrest
Consult your vehicle owner’s manual.
Rear
Headrests
Back Seat
Belt Buckles
Center Lap
Belt
Back Seat
Retractor
Lap/Shoulder
Belt
Vehicle lower anchor bars
Seat Crease
Embrace 35 Convenience Base
Locking Clip
Lower Anchor
Connector Assembly
Angle Indicator
Vehicle Seat Belt/Lower Anchor
Connector Assembly
Harness Path
12
Level
Adjustment
Button
Visual Glossary
Front Seat
Front Seat Lap and Shoulder Belts
Front Headrests
10
20
30
4
120
A I R B A G
I
I
MPORTANT
Consult your vehicle owner’s manual to determine
proper placement of child restraint in your vehicle and familiarize
Front Seat Retractor yourself with your vehicle’s components.
Convenience Base Identification
Embrace 35
Convenience Base
This is the correct base to use with the Embrace
35 Carrier.
ONLY
use the
Embrace 35 Carrier with this base.
Embrace
Convenience Base
This base
DOES NOT
work with the Embrace 35
Carrier.
NEVER
use it with the Embrace 35 Carrier.
Adjustment Foot Level Window
13
Child Seat Features
Front
1
2
3
4
5
6
ARMPIT LEVEL
Back
13
14
15
14
7
8
9
10
11
12
16
17
18
Child Seat Features
Description
1.
Handle
2.
SensorSafe Chest Clip
3.
Seat Pad
4.
Buckle Release
5.
Harness Release Button
6.
Harness Adjuster Strap
7.
Canopy
8.
Harness Slots
9.
Instruction Storage Area (behind seat pad)
10.
Harness Straps
11.
Carrier
12.
Convenience Base
13.
Handle Release
14.
Harness Straps
15.
Harness Adjuster Strap
16.
Carrier Release Handle
17.
Harness Slots
18.
Handle Release
19.
Crotch Strap Anchor
19
15
Using the Embrace Handle
To change handle positions, squeeze both
Handle
Releases and rotate the handle to the desired position.
When the handle is locked into position, the
Lock
Indicator will be green.
Position 2*
Position 3*
Position 1
Position 4
Handle
Releases Lock Indicator
Position 5
*IMPORTANT: NEVER
use Positions 2 or 3 when
traveling in a vehicle. U.S. and Canadian models differ in acceptable handle positions for travel
(see page 17).
16
Using the Embrace Handle
IMPORTANT: Always secure the child in the carrier.
Refer to “Securing your Child in the Carrier” on page 33.
Position 1 (Travel – U.S. and Canada)
This position can be used while traveling in a vehicle.
For Canadian
Models, you MUST place the handle in this position
while traveling.
Position 2 (Carry)
This position is
ONLY
to be used to carry your child.
NEVER
use this position in a vehicle.
Position 3 (Convenience)
NEVER
use this position to carry your child in the carrier.
NEVER
use this position in the vehicle.
Position 4 (Travel – U.S.)
This position can be used while traveling in a vehicle
(U.S).
For Canadian
Models, you MUST place the handle in Position 1
while traveling.
17
Position 5 (Travel – U.S. and Stand)
Place the handle in this position when you set the carrier on the floor.
This position can be used while traveling in a vehicle (U.S.). For Canadian
Models, you
MUST
place the handle in Position 1 while traveling.
Proper Installation
WITH the Convenience Base
Child Requirements
Weight: 1.8 – 15.8 kg (4 – 35 lbs)
Height:
43 – 76 cm (17 – 30 in.) and top of child’s head is at least 25 mm (1 in.) below the top of the child restraint seat back.
At least 25 mm
(1 inch)
Harness straps at, or below, the shoulder.
ARM
PIT LEV
Lower Anchor
Connector Assembly/
Vehicle Belt Path
IMPORTANT: Once your child exceeds any of the size requirements above, they
MUST
discontinue use of this child restraint.
T
IP
!
!
To make installation easier, watch the installation video of this child restraint at www.evenflo.com.
18
Installation Checklist
1. Secure convenience base to the vehicle seat.
a lower anchor connector assembly (shown)
(pages 20-22).
OR a vehicle seat belt (pages 23-25).
IMPORTANT: A properly secured convenience base
does NOT move more than 25 mm (1 inch) from side-to-side or from front-to-back at the lower
anchor connector assembly/vehicle belt path.
a indicator is completely green (pp. 21 and 23).
a and placed beneath the front edge of the base for additional leveling (p. 26).
2. Secure child to the carrier.
Refer to p. 33.
a
(p. 36).
a a
Chest clip is connected and positioned at armpit level (p. 34).
a should not be able to pinch the harness (p. 34).
a
NOT
under the child’s bottom (p. 38).
3. Check your work.
a
NOT
move more than 25 mm (1 inch) from side-to-side or from front-to-back at the lower anchor connector
assembly/vehicle belt path.
a showing in the level indicator window (pp. 21 and 23).
a
place the handle in one of the following positions when traveling in a vehicle:
U.S. - Positions 1, 4 or 5; Canada -
ONLY
Position 1 (p. 16).
19
Installing the Convenience Base with the Lower Anchor Connector
Assembly
WARNING
• This lower anchor connector assembly is intended to be used ONLY as described in these instructions.
Serious injury or death may result from misuse.
• In addition to these instructions, read and follow your vehicle owner’s manual regarding installation of the child restraint and LATCH. If there is a discrepancy, follow your vehicle owner’s manual.
•
ONLY
use for securing convenience base to vehicle lower anchor bars.
•
NEVER
attach two lower anchor assembly connectors to one vehicle lower anchor bar.
•
NEVER
use the vehicle seat belts when using the lower anchor connector assembly. Using both together can cause slack in a sudden stop or crash.
• When not in use, the lower anchor connector assembly connectors should be securely stored in the storage area located in the convenience base (see page 40).
Keep out of reach of children.
•
ALWAYS
be sure that the lower anchor connector assembly connectors are fully engaged onto the vehicle lower anchor bars by pulling hard on the lower anchor connector assembly harness. If they are not totally engaged, the lower anchor connector assembly system will not secure your child restraint. Serious injury or death may result.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) side-to-side or front to back at the vehicle belt path. Serious injury or death may result from poor installation. If you can not tightly secure the child restraint, try again or move it to another location.
• This child restraint
MUST
face the rear of the vehicle.
• The carrier MUST be locked firmly into the base.
Check by lifting up on the carrier.
• NEVER use this child restraint in the forward-facing position.
20
1
A
Before you begin, be sure the
vehicle is on a level surface.
Place the base
A
on the vehicle seat and check the level indicator
B
.
B
C
If the indicator is
red
, adjust the level of the base by pressing adjustment button
C
and lowering the adjustment foot
D has multiple levels.
.
Note: The adjustment foot
D
The base is level when only green (no red) is showing in the level indicator window
B
.
T
IP
!
!
A green filled window means go to Step 2.
IMPORTANT
Not all models are equipped with an adjustment foot. If your model does not have one, use a rolled-up towel to adjust base level (p. 26).
2
A
Route lower anchor connector assembly harness and hook through lower anchor connector assembly openings A on the sides of the base.
21
3
Know Your Lower Anchor
Connector Assembly
The lower anchor connector assembly that comes with your child restraint will be one of the types below.
SecureRight Quick Connector
Adjuster
Strap
Clip
Hook
Strap
Adjuster
K
J
L
J
J
Refer to your vehicle owner’s manual to locate the lower anchor bars
J on your vehicle seat. Attach the right hook
K
, or clip
L
, to the right anchor bar
J
and the left hook, or clip, to the left anchor bar.
DOUBLE CHECK
that the lower anchor connector hook, or clip, is fully engaged by pulling hard on the lower anchor connector strap.
4
Using your full weight, push the base firmly into the vehicle seat, while pulling up on the strap to tighten.
5
A
WARNING
E
D
Make sure the lower anchor connector assembly harness is tight.
Grab the base at the areas
D
, as shown. If you can or front to back the harness is not tight enough. You will need to try again, or find another location for your convenience base.
move the base more than
25 mm (1 inch) side-to-side
Route any excess lower anchor connector assembly
harness strap through the openings
E
IMPORTANT
A
when attaching the carrier.
, on the sides of the base, so it does not interfere with the metal carrier
retainers
22
Installing the Convenience Base with the Vehicle Seat Belt
WARNING
• The carrier MUST be locked firmly into the convenience base. Check by lifting up on the carrier.
• NEVER use this child restraint in the forward-facing position.
•
DO NOT
use this child restraint rear-facing in a vehicle equipped with lap belts that only lock during a sudden stop or crash (emergency locking retractor – ELR). You must use a seating location with a locking seat belt.
Check your vehicle owner’s manual to see if you have lap belts with ELR’s.
1
Before you begin, be sure the vehicle is on a level surface.
A
Place the base level indicator
A
B
.
on the vehicle seat and check the
B
C
If the indicator is
red
, adjust the level of the base by pressing adjustment button
C
and lowering the adjustment foot has multiple levels.
D
.
Note: The adjustment foot
D
T
IP
!
!
The base is level when only green (no red) is
showing in the level indicator window.
IMPORTANT
Not all models are equipped with an adjustment foot.
If your model does not have one, use a rolled-up towel to adjust base level (p. 26).
23
2
F
Secure the base to your vehicle seat by routing the vehicle seat belt through the openings
F on the sides of the base.
IMPORTANT: Some ELR vehicle belts can be switched so
that they lock when tightened.
It may not be necessary
to use a locking clip in these situations.
To install a locking clip, refer to p. 41.
Refer to the vehicle owner’s manual to determine which type of belt retractor is in the vehicle.
LAP BELT
LAP AND
SHOULDER BELT
3
G
H
Pull the shoulder belt
G
tightly to remove all slack from the lap portion of the belt
H
, at the same time push down on the base using your full weight. Check to be sure the base is secured in the vehicle seat.
4
F
J
I
WARNING
Make sure the vehicle belt is tight. Grab the base at the areas
I
, as shown. If you can move the base more than
25 mm (1 in.) side-to-side or front to back the vehicle belt is not tight enough. You will need to try again, or find another location for your convenience base.
IMPORTANT: Route any excess vehicle belt through the openings
F
, on the sides of the base, so it does
not interfere with the metal carrier retainers when attaching the carrier.
J
Placing the Carrier in the Base
1
Secure the carrier to the base by placing it into the base and pressing down on the front and back.
The carrier MUST be locked firmly into the
base. Check by lifting up on the carrier handle or the front of the carrier to make sure it’s locked in place.
24 25
2
B
The level indicator must be completely green
If you have fully adjusted the convenience base and the level indicator is still not level, use a tightly rolled towel or small blanket
B
A
.
beneath the front edge of the base.
IMPORTANT: Infants may have difficulty breathing when in a sitting position. Make sure they recline enough for their head to lie back comfortably and safely. Failure to properly recline the child restraint could increase the child’s risk of serious injury or death.
3
Canadian OR
U.S. Models
Position 1
U.S. Models ONLY
Position 4 or
Position 5
Releasing the Carrier from the Base
A
Position 2
B
C
Move the handle
A squeezing in on both handle releases on the carry handle release handle
C
to
A
Position 2 (Carry) by
C
B
with one hand, then lift up
with the other hand while the
is still fully retracted.
and rotating the handle until it locks into place above the carrier.
Pull the release handle
C
C
Squeeze both handle releases
C
and move the handle until it locks in position.
ALWAYS
place the handle in one of the following positions when traveling in a vehicle: U.S. - Positions 1, 4 or 5; Canada -
ONLY
Position 1 (p. 16).
Note: When installed directly behind a front vehicle seat, make sure there is at least 38 mm (1.5 inches) of space between any part of the carrier and the vehicle seat that is directly in front of the child’s head.
If you need additional clearance, place the handle in
Position 1.
26 27
Proper Installation
WITHOUT the Convenience Base
Child Requirements
Weight: 1.8 – 15.8 kg (4 – 35 lbs)
Height:
43 – 76 cm (17 – 30 in.) and top of child’s head is at least 25 mm (1 in.) below the top of the child restraint seat back.
Harness straps at, or below, the shoulder.
At least 25 mm
(1 inch)
ARM
LEV
EL
IMPORTANT: Once your child exceeds any of the size requirements above, they
MUST
discontinue use of this child restraint.
T
IP
!
!
To make installation easier, watch the installation video of this child restraint at www.evenflo.com.
28
Installation Checklist
1. Place the child in the carrier.
a the back and bottom surfaces of the carrier.
a below the top of the child restraint seat back.
2. Secure child to the carrier.
Refer to p. 33.
a level (p. 36).
a a
Chest clip is connected and positioned at armpit level (p. 34).
a should not be able to pinch the harness
(p. 34).
a
NOT
under the child’s bottom (p. 38).
3. Secure child restraint to the vehicle seat.
a belt (p. 30).
a lying across the vehicle seat back, (p. 31).
a a
ALWAYS
place the handle in one of the following positions when traveling in a vehicle:
U.S. - Positions 1, 4 or 5; Canada -
ONLY
Position 1 (p. 16).
a and placed beneath the front edge of the carrier so the child’s head lies back comfortably (p. 32).
4. Check your work.
a
To properly protect your child, the carrier
MUST
NOT
move more than 25 mm (1 in.) from side-to-side or from front-to-back at the vehicle
belt path.
29
Installing the Carrier without the
Convenience Base
1
3
C
LAP BELT
LAP AND
SHOULDER BELT
D
A
After securing the infant, place the restraint into your vehicle. Adjust the restraint so that the level line
A
is parallel with the vehicle floor.
Note: Generally, the center rear seating position is the safest. This infant restraint
MUST face the rear of the vehicle.
2
Position 4
B
Move the handle out of the way by squeezing both handle releases
B
and placing in Position 4.
30
Route
ONLY
the lap portion of the vehicle seat belt through the vehicle belt slots
C
on the carrier.
In vehicles with a lap and shoulder belt
D
,
DO NOT
route the shoulder belt through the belt slots. Instead,
To install a locking clip, refer to p. 41.
Refer to the vehicle owner’s manual to determine which
type of belt retractor is in the vehicle. let it lay across the vehicle seat back, as shown.
IMPORTANT: Some ELR vehicle belts can be switched so
that they lock when tightened.
It may not be necessary
to use a locking clip in these situations.
4
T
IP
!
!
Push down on the bottom of the seat using your full weight.
E
WARNING
• NEVER use this child restraint in forward-facing position.
•
DO NOT
use this carrier if it moves more than 25mm
(1 in.) side-to-side or front to back at the vehicle belt path. Serious injury or death may occur. Move the child restraint to another seating location, or try to tighten the vehicle belt again.
The vehicle belt
E
must be as tight as possible. Put your full weight into the seat as you tighten the vehicle belt.
If you can move the child restraint more than 25 mm
(1 in.) side-to-side or front to back at the vehicle belt path, the vehicle belt is not tight enough, and you need to try again.
31
5
Canadian OR
U.S. Models
Position 1
U.S. Models ONLY
Position 4 or
Position 5
Securing the Child in the Carrier
B
B
Squeeze both handle releases
C
and move the handle until it locks in position.
ALWAYS
place the handle in one of the following positions when traveling in a vehicle: U.S. - Positions 1, 4 or 5; Canada -
ONLY
Position 1 (p. 16).
Note: When installed directly behind a front vehicle seat, make sure there is at least 38 mm (1.5 inches) of space between any part of the carrier and the vehicle seat that is directly in front of the child’s head.
If you need additional clearance, place the handle in
Position 1.
6
A
Place the baby into the carrier. Baby’s bottom and back should be flat against the seat. If there is a gap, baby will not be comfortable.
1
Slide each harness strap over the child’s shoulders.
ARMPIT LEVEL
2
ARMPIT
LEVEL
Insert the buckle tongues into the buckle. Pull up on the harness strap to ensure the buckle tongues are engaged.
F
If the level line
A
is not parallel to the vehicle floor, use a tightly rolled towel or small blanket
F
beneath the front edge of the child restraint to provide enough recline for an infant’s head to lie back comfortably.
IMPORTANT: Infants may have difficulty breathing when in a sitting position. Make sure they recline enough for their head to lie back comfortably and safely. Failure to properly recline the child restraint could increase the
child’s risk of serious injury or death.
32
IMPORTANT: The buckle strap should be snug against the baby’s crotch, but never under the baby’s bottom.
Adjust the crotch strap if necessary (p. 38).
33
3
A
ARMPIT LEV
EL
VEL
ARMP
IT LE
Align the two sides of the chest clip
A
and snap them together. The chest clip must be positioned at armpit level.
See page 44 for
SensorSafe Chest Clip usage instructions.
The harness straps must be snug against the child.
A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. Check the harness straps near the shoulders for slack. You should
NOT
be able to pinch the harness (see illustration). Adjust as needed.
4
Removing the Child from the Carrier
1
Press the red buckle release
A
, and remove the buckle tongues.
ARM
PIT
LE
VE
A
2
B
3
Push the release button and pull the chest clip apart.
B
ARM
PIT
VEL
D
C
To loosen the harness straps, press the harness release button harness straps
C
D
.
while pulling upward on the
B
To tighten the harness straps, pull the harness adjuster strap as shown.
B
on front of the restraint,
34 35
Changing the Harness Position
As your child grows, you will need to change the harness strap position so they are routed through the slots closest to the child’s shoulders. The shoulder harness straps should ALWAYS be as close as possible to,
but
NEVER above the child’s shoulders.
1
Loosen the harness straps
A button
by pressing the harness release
B
while pulling on the straps.
A
B
2
E
C
D
There are two positions
on the harness straps.
The top loop newborn use. The bottom pocket
D
C
is for
is for use as your child grows.
Slide the harness strap off of the splitter plate E .
4
ARMPIT LEVEL
A
Insert both harness straps
A
into the new harness position slots.
5
Attach the appropriate pocket on the harness straps plate
A child’s size) to the splitter
E
(according to your
. Harness straps must
NEVER
be routed over the base release lever.
E
A
3
A
ARMP
Pull both harness straps through the front of the child restraint.
A
36
6
WARNING
Make sure both harness straps are installed
completely on the splitter plate, as shown.
Failure to properly attach the harness straps to the splitter plate may result in a loose harness and serious injury or death to your child.
F
Tighten the harness straps by pulling the adjustment strap
F
on front of the restraint.
Note: Final adjustment of the harness straps must be completed with the baby in the child restraint.
37
Changing the Crotch Strap Position
As your child grows, you will need to change the crotch strap position so that it is in the slot closest to your child.
The crotch strap should
ALWAYS
be as close as possible to, but
NEVER
under, the child’s bottom.
There are four positions for the crotch strap to be used based upon your child’s comfort.
Crotch Strap in the Newborn Position
NEVER
use this position for children weighing more than 3.6 kg (8 lbs).
ARMPIT LEVEL
Crotch Strap in the Rear Slot
ARMPIT LEVEL
1
B
A Loosen the harness straps (p. 36) and move the strap way.
A
out of the
Remove the crotch strap anchor
B
from its position on the bottom of the carrier, and push the anchor up through the slot to the top of the seat.
2
ARMPIT LEVEL
B
Insert the crotch strap anchor B into the slot that is the closest to the child
AND
the
most
comfortable for the child.
Crotch Strap in the Middle Slot
ARMPIT LEVEL
Make sure the anchor is completely through and is lying flat against the bottom of the seat. Pull up on the crotch strap to make sure it is securely fastened.
3
B
Crotch Strap in the Front Slot
ARMPIT LEVEL
38
For newborn position, place the anchor through the rear slot, then feed it through the middle slot.
B
Make sure the anchor is completely through the middle slot and is lying flat against the bottom of the seat.
NEVER
use this position for children weighing more than 3.6 kg (8 lbs).
39
Removing the Lower Anchor
Connector Assembly
1
Tilt and slide the adjuster to loosen the lower anchor connector assembly.
Press the adjuster release button to loosen the lower anchor connector assembly
Adjuster
Or
Adjuster Release
Button
3
E
2
The Lower Anchor Connector that comes with your child restraint will be one of the types below.
C
E
D
To remove the hook press the tab
D
and
C
, twist, then remove from anchor
E
.
F
E
G
To remove the clip pull the red release strap
G
and remove clip from anchor
E
.
F
,
40
F
F
When the lower anchor connector assembly is not in use, you
MUST
securely store it in the area provided in the bottom of the base
E
.
Route the harness strap through the belt path on top of the base then attach the hooks to the slots
F
located on each side of the storage area beneath the base.
A loose lower anchor assembly connector harness and hook may injure your child.
Using the Locking Clip
To watch a video about installing a locking clip, go to
www.evenflo.com.
Locking Clip installed properly.
13 mm
(0.5 inch)
Install Locking Clip, if necessary.
If your vehicle was built prior to model
year 1996, and has a lap/shoulder belt that is equipped with an emergency locking retractor (ELR) AND sliding latch plate, you
MUST
use a Locking Clip. Check your vehicle owner’s manual to identify which vehicle belt system is in your vehicle.
If your vehicle is model year 1996 or newer, it likely has a vehicle belt system that can be locked when tightened, and will not require use of a Locking Clip.
Consult your vehicle owner’s manual before installing a Locking Clip.
41
1
WARNING
Remove locking clip from vehicle seat belt when not used with a child restraint, or the vehicle seat belt will not properly restrain an adult or child.
Serious injury could occur.
C
B
A
D
T
IP
!
!
Push down on the base using your full weight.
Remove the locking clip convenience base.
A
from the slot in your
Thread the vehicle seat belt through the belt path openings
B
for the vehicle belt path, and buckle the vehicle seat belt.
Pull the vehicle shoulder belt slack from the lap portion
C
tightly to remove all
D
of the vehicle belt.
2
E
3
A
E
While holding the belts and buckle tongue E the locking clip
, thread
A onto the vehicle seat belt, and slide it into place.
Note: Locking clip must be placed within 13 mm
(0.5 in.) of seat belt buckle.
A
13 mm (0.5 in.)
A
4
Buckle the vehicle seat belt with the locking clip
A
in place.
• If installing the convenience base with a vehicle seat belt, return to page 24, Step 3.
• If installing the carrier (no convenience base) with a vehicle seat belt, return to page 31, Step 4.
Hold the vehicle lap/shoulder belts together just behind the free sliding buckle tongue unbuckle the vehicle seat belt.
E
and
42 43
General Information about SensorSafe
TM
Secure your child into the child restraint as you would normally. The SensorSafe Receiver Plug monitors both the Chest Clip Transmitter and the vehicle. When you arrive at your destination and turn your vehicle off, the SensorSafe system sounds a series of gentle tones reminding you that your baby is in the vehicle.
Install it once and SensorSafe is always ready to alert you.
WARNING
This product contains magnets.
Before use, consult your family doctor about the compatibility of this product with pacemakers and similar devices.
Important Usage Information
• SensorSafe is compatible ONLY with Evenflo
Embrace Infant Car Seats that have a maximum weight rating of greater than 30 lbs.
• The SensorSafe system consists of two components:
1. The Chest Clip Transmitter and 2. The Receiver
Plug. The system will not work unless both of these components are present in the vehicle with the
Receiver installed in the vehicle’s OBDII port (p. 46).
ARM
PIT
LEV
EL
Chest Clip Transmitter Receiver Plug
• The SensorSafe Chest Clip is designed to go into a sleep mode after being clipped for 12 hours.
Although 12-hour vehicle trips without stops are uncommon and not recommended, the Chest
Clip must be opened and closed after 12 hours to reactivate the SensorSafe system.
• The Receiver Plug works ONLY with 2008 or newer gas/diesel equipped vehicles purchased in the U.S. or Canada. If you would like to use the SensorSafe
Chest Clip with a Hybrid or Stop/Start vehicle, please contact Evenflo’s ParentLink at:
1-800-233-5921 (U.S.), 1-937-773-3971 (Canada), or 01-800-706-12-00 (Mexico) to order a compatible Receiver Plug.
44
General Information about SensorSafe
TM
Battery Usage
• To preserve battery life, always store the SensorSafe
Chest Clip in the un-clipped position.
• The Chest Clip includes 1-button cell lithium battery that cannot be recharged or replaced.
Dispose of Chest Clip properly.
• The SensorSafe battery should last for the life of this car seat, but is designed to alert you of a low battery. If your Chest Clip battery is getting low, the SensorSafe Receiver will make a “low battery” alarm when the Chest Clip is closed. This “low battery” alarm will sound different from the beeps you typically hear when activating your SensorSafe system. Please contact Evenflo’s ParentLink at:
1-800-233-5921 (U.S.), 1-937-773-3971 (Canada), or 01-800-706-12-00 (Mexico) to order a replacement SensorSafe Chest Clip.
SensorSafe
™
Technology
Questions? Comments?:
Visit us at: www.evenflo.com
Or call ParentLink at: 1-800-233-5921 (U.S.),
1-937-773-3971 (Canada), or
01-800-706-12-00 (Mexico).
This device meets the requirements of SAE J3005.
FCC Certified - Model: SOS, FCC ID: 2ABS2-SOSR1
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Industry Canada (IC) Certified - Model: SOS, IC ID:
11740A-SOSR1
This device complies with Industry Canada Licenseexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept interference, including any interference that may cause undesired operation of this device.
45
Using SensorSafe
1
Install the SensorSafe Receiver.
Locate the 16PIN OBDII port
A
in your vehicle.
Refer to your vehicle owner’s manual for location.
A
Plug in the SensorSafe
Receiver.
Your SensorSafe Receiver will sound one prolonged tone when it first communicates with the vehicle network. In some vehicles this occurs immediately after installing the SensorSafe Receiver, in other vehicles the tone will not be heard until the vehicle has been started.
This initialization signal only occurs one time after installation.
2
Power up the vehicle.
3
Cycle the SensorSafe Chest Clip.
Your SensorSafe Chest
Clip is designed to “go to sleep” if clipped for more than 12 hours. The chest clip will “wake up” or reset by simply opening and closing. TO PRESERVE
BATTERY LIFE, ALWAYS
STORE THE SENSORSAFE
CHEST CLIP IN THE
UN-CLIPPED POSITION.
4
Drive the vehicle.
The SensorSafe Receiver is designed to respond after the vehicle has been driven for 30 seconds at 5 miles per hour or more.
46
Using SensorSafe
5
Park the vehicle and turn off the ignition.
Within 2 seconds of parking your vehicle and turning off the ignition you will hear the SensorSafe reminder, alerting you that your baby is in the vehicle.
If you don’t hear the reminder tone, test your
SensorSafe by following steps 1-5 again. Contact
Evenflo’s ParentLink at: 1-800-233-5921 (U.S.),
1-937-773-3971 (Canada), or 01-800-706-12-00
(Mexico) if the reminder tone again fails to sound.
Note: SensorSafe Receiver will also alarm within 30 seconds if your child un-clips the Chest Clip after the vehicle has been driven for 30 seconds at 5 miles per hour or more, but only if the vehicle is on.
47
Using as an Infant Carrier
Secure the child in the carrier by following “Securing the
Child in the Carrier” on page 33.
Position 5
Lock Indicator
To use as a stand: Squeeze both handle releases and rotate the handle to Position 5 (Stand) until it locks into place (the Lock Indicator will be green) and the carrier rests on a level surface.
Position 2
WARNING
•
NEVER
place this carrier near the edges of counter tops, tables, or other high surfaces. The child’s movements can cause the carrier to slide and fall.
•
NEVER
leave the child in this carrier when the harness straps are loose or undone. Children have STRANGLED in loose or partially buckled harness straps. Fully restrain the child even when carrier is outside the vehicle.
•
NEVER
place the carrier in any position in a shopping cart.
The carrier may fall from the cart and your child may be injured.
•
DO NOT
carry on your hip.
To use as a carrier: Squeeze both handle releases and rotate the handle to Position 2 (Carry) until it locks into place (the Lock Indicator will be green).
Carry at your side, using the handle as shown.
IMPORTANT
The harness MUST be securely buckled at all
times.
ARMPIT LEVEL
48 49
Securing Your Child Restraint in
Aircraft
The Federal Aviation Administration (FAA) recommends that you secure your child for air travel in an appropriate child restraint based on your child’s weight and size. Turbulence can happen with little or no warning. When turbulence occurs, the safest
place for your child is in a properly installed child restraint, not in an adult’s lap or on the
aircraft seat with its seat belt. Keeping your child in a child restraint during the flight will help ensure your family arrives safely at your destination.
The FAA recommends that a child weighing:
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child restraint; and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing child restraint.
Please note that these FAA recommendations may vary from those applicable to the use of your child restraint in a motor vehicle.
IMPORTANT
You must use the internal harness when installing the child restraint in aircraft.
In order to comply with the FAA regulation for Portable Electronic Devices (PED), the
SensorSafe Chest Clip
MUST
be unfastened before take-off.
Note: After landing, fasten the SensorSafe Chest
Clip before removing the Embrace Infant Car Seat from the Aircraft seat.
Installing Convenience Base in
Aircraft
IMPORTANT: Before installing the child restraint, make sure the aircraft seat is in a fully upright position.
1
A
Place the base level indicator
A
B
.
on the aircraft seat and check the
B
C
If the indicator is
red
, adjust the level of the base by pressing adjustment button
C
and lowering the adjustment foot has multiple levels.
D
.
Note: The adjustment foot
D
T
IP
!
!
The base is level when only green (no red)
is showing in the level indicator window.
IMPORTANT
Not all models are equipped with an adjustment foot.
If your model does not have one, use a rolled-up towel to adjust base level (p. 26).
50 51
2
Installing Convenience Base in
Aircraft
F
Secure the base to the aircraft seat by routing the aircraft seat belt through the openings sides of the base.
F
on the
3
A
B
D
The aircraft seat belt
Route the excess seat belt strap belt slots
B
A
must be as tight as possible.
D
back through the
, as shown above. Using your full weight, push the base firmly onto the aircraft seat while pulling on the excess seat belt strap to tighten.
Check your work. Try to move the base in all directions. If you can move the base more than 25 mm (1 inch) side-to-side or front to back at the belt path
B
, the aircraft seat belt
A
is not tight enough, and you
MUST
install again until the seat belt is tight.
52
4
5
Installing Convenience Base in
Aircraft
Placing the Carrier in the Base
Secure the carrier to the base by placing it into the base and pressing down on the front and back.
The carrier MUST be locked firmly into the
base. Check by lifting up on the carrier handle or the front of the carrier to make sure it’s locked in place.
Position 1
C
Squeeze both handle releases to Position 1.
C
and move the handle
6
Unfasten SensorSafe Chest Clip
As a final step, unfasten the chest clip (p. 35).
ARM
PIT LE
VEL
In order to comply with the
FAA regulation for Portable
Electronic Devices (PED), the
SensorSafe Chest Clip
MUST
be unfastened before take-off.
Note: Make sure harness straps are tight before unfastening the chest clip.
Note: After landing, fasten the
SensorSafe Chest Clip before removing the Embrace Infant Car
Seat from the Aircraft seat.
53
1
Installing Carrier without
Convenience Base in Aircraft
3
Installing Carrier without
Convenience Base in Aircraft
B
ARMPIT
LEVEL
Aircraft
Seat Belt
Place the child restraint on the aircraft seat rear-facing, as shown above.
2
Position 4
A
Route the aircraft seat belt the carrier, as shown above.
A
through the belt slots
B
on
4
C
Move the handle out of the way by squeezing both handle releases
C
and placing in Position 4.
ARMPIT
LEVEL
A
Fasten the aircraft seat belt
A
.
54 55
5
Installing Carrier without
Convenience Base in Aircraft
D
A
ARMPIT
LEVEL
B
The aircraft seat belt
Route the excess seat belt strap belt slots
B
A
must be as tight as possible.
D
back through the
, as shown above. Using your full weight, push the child restraint firmly onto the aircraft seat while pulling on the excess seat belt strap to tighten.
Check your work. Try to move the child restraint in all directions. If you can move the child restraint more than 25 mm (1 inch) side-to-side or front to back at the belt path
B
, the aircraft seat belt
A
is not tight enough, and you
MUST
install again until the seat belt is tight.
6
Position 1
C
Squeeze both handle releases
C
and move the handle to Position 1.
7
Unfasten SensorSafe Chest Clip
PIT LE
VEL
As a final step, unfasten the chest clip (p. 35).
In order to comply with the
FAA regulation for Portable
Electronic Devices (PED), the
SensorSafe Chest Clip
MUST
be unfastened before take-off.
Note: Make sure harness straps are tight before unfastening the chest clip.
Note: After landing, fasten the SensorSafe Chest Clip before removing the Embrace Infant Car Seat from the Aircraft seat.
56
Installing the Canopy
A
B
Insert front canopy end
A
Repeat on the other side.
into the holder
B
.
1
Installing the Accessories
Not available on all models.
ARMPI
EL
B
A
The optional Body
Pillow A is used to help support your child by placing it in the restraint, as shown.
The optional Head Support the seat back, as shown.
B
should lie flat against
Be sure to cut off the plastic attachment between the head support and the seat pad. Small parts may be a choking hazard.
WARNING
Support the child’s head. Infants may have difficulty breathing when in a sitting position. Using additional padding or pillows behind the infant’s head, or failure to properly recline the child restraint could increase the child’s risk of serious injury or death.
57
Installing the Accessories
2
Not available on all models.
Place the optional
Boot C over the child restraint and your child.
C
D E
Replacement Parts
Not available on all models. Styles may vary.
To order replacement parts you can order online at
www.evenflo.com or contact Evenflo. When you contact us, please have the product model number and date of manufacture (found on the back of the child restraint).
Locking Clip
Head Foam
(Canada only)
EPS Foam
E
G
F
Fasten Velcro
®
strips D to each other. Fasten the boot to the seat pad with snaps E .
IMPORTANT:
When installing the carrier in a vehicle or aircraft without the convenience base, ensure the seat belt properly through the belt slots boot to the child restraint.
G
F
is routed
before securing the
Canopy
Harness System
ARM
PIT
LEV
EL
SensorSafe
Chest Clip
Head Support
Body Pillow
Seat pad
58
Boot
Accessory Base
Lower Anchor
Connector Assembly
Or
59
Lower Anchor
Connector Assembly with Quick
Connectors™
Proper Disposal of this Child Restraint
At the end of this child restraint’s useful life, Evenflo encourages you to dispose of it properly. Most of the components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding, you may dispose of it in the landfill.
Note: Evenflo uses recycled materials in the manufacturing process whenever possible but never for components that are critical for safety.
To prevent injury due to hidden damage, lost instructions, outdated technology, etc., discontinue use of this restraint after the expiration date on the label or if it has been involved in a crash.
Limited Warranty
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories) against defects in material or workmanship. Evenflo’s sole obligation under this express limited warranty shall be, at Evenflo’s option, to repair or replace any
Product that is determined to be defective by Evenflo and determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form of a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain warranty service.
This express limited warranty is extended by Evenflo
ONLY to the original Purchaser of the Product and is not assignable or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo’s ParentLink Consumer Resource
Center at (800) 233-5921 (U.S.), (937) 773-3971
(Canada), or www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS
HEREBY DISCLAIMED. EVENFLO SHALL NOT BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL,
SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR
BREACH OF THE EXPRESS LIMITED WARRANTY ON
THIS PRODUCT, OR ANY WARRANTY IMPLIED BY
OPERATION OF LAW. OTHER THAN THE EXPRESS
LIMITED WARRANTY SET FORTH ABOVE, THERE ARE
NO OTHER WARRANTIES THAT ACCOMPANY THIS
PRODUCT AND ANY ORAL, WRITTEN OR ANY OTHER
EXPRESS REPRESENTATION OF ANY KIND IS HEREBY
DISCLAIMED.
Manufactured in Fabriqué en
(year-month-day)
(anné-mois-jour)
Name / Nom
Model / Modéle
Made in / Fabriqué en
Expires on/Expire le
60
www.evenflo.com
USA: 1-800-233-5921, 8 AM – 5 PM E.T.
Canada: 1-937-773-3971
México: 01-800-706-12-00
61
ARMPIT LEVEL
After thoroughly reading and following these instructions, store them in the carrier behind the seat pad, as shown.
www.evenflo.com
USA: 1-800-233-5921, 8 AM – 5 PM E.T.
Canada: 1-937-773-3971
México: 01-800-706-12-00
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - Premature Infant Use
- - Warnings
- 3 LATCH Warnings
- 5 Recall Information for U.S. Customers
- 6 Public Notice for Canadian Customers
- 6 Motor Vehicle/Airplane Usage
- 7 Care and Cleaning
- 7 Storing Your Instructions
- 8 Visual Glossary
- 12 Using the Embrace Handle
- 15 Installation Checklist
- 16 the Lower Anchor Connector Assembly
- 19 the Vehicle Seat Belt
- 21 Placing the Carrier in the Base
- 23 Releasing the Carrier from the Base
- 25 Installation Checklist
- 26 Installing the Carrier without the Convenience Base
- 29 Securing the Child in the Carrier
- 31 Removing the Child from the Carrier
- 32 Changing the Harness Position
- 21 Changing the Crotch Strap Position
- 22 Removing the Lower Anchor Connector Assembly
- 22 Using the Locking Clip
- 24 General Information about SensorSafe
- 25 Using SensorSafe
- 26 Using as an Infant Carrier
- 27 Securing Your Child Restraint in Aircraft
- 27 Installing Convenience Base in Aircraft
- 29 Installing Carrier without Convenience Base in Aircraft
- 30 Installing the Canopy
- 31 Replacement Parts
- 32 Limited Warranty