Extra Small & Small Owner’s Manual SYMBOL LEGEND ! CAUTION/ATTENTION ENVIRONMENTAL CONDITIONS TYPE BF APPLIED PART DATE OF MANUFACTURE PINCHPOINT SN SEE INSTRUCTIONS FOR USE SERIAL NUMBER Please be environmentally responsible and recycle this product through your recycling facility at its end of life. Afin de préserver l’environnement, veuillez confier ce produit à votre centre de recyclage à la fin de sa durée de vie. Nachdem dieses Produkt ausgedient hat, entsorgen Sie es bitte auf umweltfreundliche Weise, indem Sie es zu der entsprechenden Recyclingstelle bringen. Wees a.u.b. milieubewust en recycleer dit product via uw recycleerder na het verstrijken van de levensduur. Sea responsable con respecto al medio ambiente y recicle este producto al finalizar su vida útil en el lugar de reciclaje correspondiente. Siate responsabili verso l’ambiente e riciclate questo prodotto, al termine della sua vita d’uso, presso la vostra sede di riciclaggio. Kierrätä tämä tuote sen käyttöiän lopussa ympäristövastuullisella tavalla paikallisella kierrätyslaitoksella. Var miljömedveten och återvinn denna produkt efter dess användning. Vi ber deg ta hensyn til miljøet og resyklere dette produktet ved hjelp av de rette resykleringsfasilitetene når produktet ikke lenger kan brukes. Vis venligst hensyn til miljøet ved at levere produktet til det nærmeste genbrugsanlæg, når det ikke længere fungerer. Por favor, assuma responsabilidade ambiental, reciclando este produto em suas instalações de reciclagem no final de sua vida útil. Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mobile Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Adjustments & Usage. . . . . . . . . . . . . . . . . . . . . . . . . . 14 Supine Option Usage. . . . . . . . . . . . . . . . . . . . . . . . . . 17 Pow’r Up Lift Option Usage. . . . . . . . . . . . . . . . . . . . . 19 Parts Detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 TroubleShooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Date Purchased Serial # Introduction Congratulations on your purchase of an EasyStand standing frame! We at Altimate Medical have designed the EasyStand with your comfort and happiness in mind. EasyStand Description The EasyStand line of products is intended for individuals who are able to transfer independently or with assistance from a caregiver and/or lifting device. It is a useful tool for rehabilitation, home, school, and work use. EasyStand standing frames support the user from sitting to the standing position. Various options such as support, choice of manual or Pow’r Up Lift may be added to facilitate individual needs. Indications for Use The EasyStand Bantam line of products is intended to assist individuals who have difficulty rising from a seating position to a standing position and is indicated for individuals weighing up to 50 lbs. (Extra Small), 100 lbs. (Small). This manual is an integral part of your standing system and s hould be read completely and thoroughly by anyone that will be operating the unit. This will ensure the EasyStand is assembled properly and used in the most beneficial manner. Altimate Medical recommends that an attendant be present when the EasyStand is being used. Should any problem arise that you cannot solve by reading this m anual, pleasecontact your local supplier or call Atimate Medical, Inc., at 800-342-8968 or 507-697-6393. It is necessary to inspect your EasyStand Bantam at least weekly to ensure it is in safe operating condition. EasyStand adjustments that are listed in the product owner’s manual can be made by the operator by following the instructions for use. After an adjustment is made, inspect the EasyStand to ensure all hardware and adjustable components are properly secured per the instructions for use. Replacement of worn parts, major adjustments, or any other important corrections should be handled by an authorized supplier or service center. Only Altimate Medical, Inc., approved replacement parts should be used to ensure safety and performance. Do not use the EasyStand Bantam without consulting your physician. Failure to consult a qualified physician prior to using the EasyStand Bantam could lead to severe medical problems. We recommend a good standing program be established and supervised by a qualified physician or physical therapist. Join the Standing Community! Our goal is simple - to empower people with disabilities to stand up for their health. Connect, share, and learn from other people with disabilities, special needs parents, clinical professionals, and the experts in standing on our social networking communities. By keeping your standing program “top of mind” you will have the greatest chance of maintaining a standing routine that maximizes all the benefits of standing! Read, share, and comment on the EasyStand Blog at blog.easystand.com Find EasyStand on these social networking sites: Page 1 Introduction Safety Precautions • Please read and understand all safety precautions and user instructions prior to use. Call Altimate Medical at 800-342-8968 or 507-697-6393 with any questions or for additional information. • If a user does not meet the specifications below and has not been properly fitted by a qualified therapist or physician, Altimate Medical, Inc., does not recommend using the EasyStand Bantam. Bantam (Extra Small) - is designed to accommodate most individuals from 28”-40” (71-102cm) and up to 50 lbs. (23kg) Bantam (Small) - is designed to accommodate most individuals from 36”-54” (91-137cm) and up to 100 lbs. (45kg) For more detailed specifications visit our website www.easystand.com • The EasyStand Bantam should not be used without first consulting a qualified physician. Failure to consult a qualified physician prior to using the EasyStand Bantam could lead to severe medical problems. We recommend a good standing program be established and supervised by a qualified, registered physical therapist. • The EasyStand Bantam should always be used with a qualified adult attendant present. Never leave a child unattended in the Bantam. • Do not make adjustments to the Bantam while in the standing position. Exception: If the supine option was ordered, refer to pages 17- 18. Changes in position must be performed or supervised by a qualified caregiver or medical professional. • It is necessary to inspect the EasyStand Bantam at least weekly to ensure it is in safe operating condition. Pay particular attention for loose hardware. If the EasyStand is equipped with the optional Pow’r up lift, please inspect the electrical cables for any wear and ensure they are attached properly. Replacement of worn parts, major adjustments, or other important corrections should be handled by an authorized dealer or service center. Only Altimate Medical, Inc., approved replacement parts should be used to ensure safety and performance. • If the EasyStand is being used in the home environment, please inspect the unit prior to each use to ensure there is no damage or unexpected wear to the EasyStand that may have been caused unintentionally by pets, pests or children. • Never reposition the foot plates while the user is in the standing position. Consult with a therapist or physician for proper foot placement and angle. • Never elevate the legs or adjust the backrest to anterior tilt using the following arm adjustment. Only the supine option may be used to elevate the legrest with simultaneous recline of the backrest. • Ensure the necessary support and alignment options are in position prior to bringing the child into the standing position. • If the unit was exposed to temperatures of less than 50˚F (23.5˚C), the unit must warm to room temperature before use. • Operating Conditions: Temperature: 41˚F (5˚C) -104˚F (40˚C), Relative humidity: 20% - 90% at 86˚F (30˚C), Atmospheric Pressure: 700 to 1060hPa. • Storage/Transport Conditions: Temperature: 14˚F (-10˚C) -122˚F (50˚C), Relative humidity: 20% - 90% at 86˚F (30˚C), Atmospheric Pressure: 700 to 1060hPa. • The EasyStand can be used at a maximum altitude of 10,000 feet (3,050 meters). • The expected service life of an EasyStand is considered 5 years under normal use conditions. Note: This may vary based on frequency of use. • Standing equipment is designed for indoor use on level surfaces only. Keep casters locked while in use. • Transporting the unit with a user in the standing position is not recommended. • Extreme movements laterally or front to back may cause the unit to tip. • It is recommended the equipment be stored at normal room temperature and humidity levels. • Altimate Medical products are specifically designed to be used with Altimate Medical accessories and options. Unless otherwise noted, accessories and options from other manufacturers have not been tested by Altimate Medical and are not recommended for use with Altimate Medical products. • Product Modifications made without express written consent (including, but not limited to, modification through the use of unauthorized parts or attachments) are not recommended and will void the product warranty. • The EasyStand Bantam Electric Lift meets the requirements of IEC 60601-1 and 60601-2.* • The wheel lock on the mobile option is to keep the unit in place while transferring or standing stationary and it is not intended to be used as a dynamic brake to stop a rolling mobile unit. ! Caution: This equipment is designed to accommodate a range of users; therefore the unit has various adjustment slots and holes. Avoid placing fingers or other body parts in any of these areas. Caution: While in use this equipment has various moving parts, familiarize yourself with the unit and avoid placing hands or fingers ! near any of these areas. Caution: Advise bystanders to keep clear of the unit while in use. ! ! Caution: Do not use the EasyStand Bantam Mobile option on an incline, it is intended for level surfaces only. Doing so may cause the unit to tip. * Bantam Pow’r Up Lift Option Only Page 2 Safety Precautions Assembly 1. The basic stander consists of three assemblies. Options are in addition to the three assemblies. • • • • If you ordered the Mobile option, please go to page 12. Front Frame Back Seat Post / Rear Frame Knee Pads 2. If you ordered the Swing-Away Front option with Front Swivel casters, attach the casters to the axel as shown. Line up the bolt and nut, using a 17mm wrench and hex wrench, tighten the nut securely. 3. Remove the two bolts and two coved nuts from front frame. Page 3 Assembly 4. Flip up the rear frame to allow easier access to the post. Attach the front and rear frames to one another. 5. Place the two coved nuts into the bottom of the frame and flush with the tube. You may have to tap them in with a rubber hammer to make them flush. 6. Place the two bolts into the top of the frame and screw into the coved nut, making sure they are flush. Tighten securely. Page 4 Assembly 7. Place the unit back in the normal position. Step on the gas spring assist pedal to raise the seat about 3/4 the way up as shown. 8. If the Supine option ordered, remove the red locking handles, bolts and washers on both sides and set aside. 9. Line up the following arm with the back angle tube. Page 5 Assembly Extra Small Small 10. Depress the spring button to allow the following arm to slide into place. Match the following arm position color with the corresponding seat depth color (for more information on seat adjustments see pg. 15). 11. If you did not order the Supine option, skip to step 13. To assemble the Supine option, put hardware in order as shown: A. Bolt B. Nylon Washer C. Beveled Metal Washer D. Small Metal Washer E. Red Supine Locking Handle 12. Follow the steps for placing hardware on unit: A B C D E One for each side of the unit. A & B - Insert nylon washer in between the brackets as shown. Insert the bolt into the square hole making sure the bolt is in all the way. C- Place beveled metal washer onto the bolt with the domed end facing outward. D- Place the small metal washer onto the beveled metal washer. A B Nylon Washer C D E E- Place the red supine locking handle onto the bolt. Repeat these steps for the opposite side. Page 6 Assembly 13. Loosen the ratchet handles on the foot plates and swivel into place (for information on foot plate adjustments see pg. 14). 14A. Insert each knee bracket into the tubes onto the unit, with the clamp down. 14B. Depress the spring button to allow the bracket to slide into place, advance until the spring button locks into place. Tighten knobs securely. 15. Insert each knee pad bracket into the slots on the knee bracket. Tighten knobs securely. A Page 7 Assembly B 16. Remove knob and metal washer from the knee pad, leaving the rubber washer in place on the knee pad, place the knee pad and rubber washer onto the knee pad bracket. Place metal washer and knob onto bolt as shown. Repeat steps for the opposite side (for information on knee pad adjustments see pg. 14). Metal Washer 17. If you ordered the optional Swing-Away Front, Remove the tray bracket from the H-frame and set the bracket aside for step 19. Place the H- frame onto the the base of the unit, making sure the swivel collar is placed onto the tube insert. If you ordered a Shadow Tray, please skip to step 23. Swivel Collar Tube 18. Insert Place the collar onto the frame until the plunger locks into place. The plunger handle needs to be pulled out to lock into place. Plunger Handle Page 8 Assembly 19. Place the tray upside down, remove the knob, nut, and washers from both tray slides and set aside. Place the tray bracket onto the bolts with the shorter ends of the bracket facing the chest pad. Remove 20A. Place the knobs onto each bolt and tighten snug. 20B. A B Place the two washers onto each bolt, then place the nut onto each bolt and tighten until you expose a thread, the washers should still be able to spin freely. 2 Washers 21. Place the table bracket into the H-frame. Page 9 Assembly 22. Depress the spring button to allow the bracket to slide into the H-frame (A). Once you clear the clamp the spring button needs to be depressed again and allow the tray to slide into position (B). Note: There is only one spring button. The spring button will stop in the maximum height position. Tighten knobs to secure the tray height. 23. If you ordered the optional Shadow Tray, loosen the ratchet handles on the side of the tray, flip the arms up so they are lined up with the tray as shown and tighten the ratchet handles. Insert the two tray arms into the tray bracket on the bottom of the tray. One of the arms is longer than the other for easier installation (for information on Shadow Tray adjustments see pg. 15). The bolts on the arms are used as a stop for future reference. Place the quick release pins into the holes of the tray to secure into place. Caution: After placing the tray into position, ensure the ratchet handles on the side of the tray are tightened securely. 24. If not already on the unit, remove the knob from the center post and place the back onto the unit as shown. A B Page 10 Assembly 26. Place the back in the desired position. Insert knob and tighten securely. 27. If you ordered only the optional headrest, insert the head support onto the unit and tighten securely. B A 28A. If you ordered only the assist handle extension, remove the foam cover from the assist handle that is on the unit. 28B. screw Place the assist handle extension onto the unit. Insert screws into the top and bottom of the handle and tighten securely. screw Page 11 Assembly Mobile Option Assembly Note: If this is an option added after the initial purchase, you must remove the existing front assembly before proceeding. 1. The Mobile option consists of two drive wheel assemblies, a “T” style front weldment, barrel nuts and bolts. You will need a 5mm allen wrench and a rubber hammer for assembly. 2. Set the Bantam on its back and attach the “T” weldment to the frame. Note that the front curves upward. 3. Line up holes and place the coved nuts on the bottom of the frame. You may have to tap them with a rubber hammer to make them flush. Tighten bolts securely. Weldment Curves Upward Page 12 Mobile Assembly 4. Attach the interchangeable right and left drive wheel assemblies to the front frame. 5. Line up the holes and tap in the coved nuts and tighten bolts securely. Making sure the coved nuts are flush with the base. Position the Bantam upright and re-tighten the frame bolts (as in step #2 on pg. 12). Return to step 7. Mobile Adjustment & Usage To lock or unlock the drive wheels, turn the drive wheel lock one quarter turn. Use the push rim adjustment to position the push rims forward or aft, for transferring or self-propulsion. Tighten to lock in position. Page 13 Mobile Assembly Independent Push Rim Angle Adjustments Independent Drive Wheel Locks Adjustments & Usage FIG. A Height Gas Cylinder Place foot on the pedal and lift using the assist handle behind the seat to help raise the unit to the standing position. This may also be necessary when lowering the user to the seated position. Both red locking handles must be loose for use in the sit-to-stand FIG. B position. Plantar/Dorsi Foot plates ! Caution: Never reposition the foot plates with the child in the standing position. ! Caution: Avoid placing fingers in the adjustment slot. FIG. A-Height-The standard foot plates have height adjustment only. FIG. C Loosen the clamp connecting the foot bracket to the seat post to Adduction adjust foot plate height. The Multi-Adjustable Foot plates have a wide variety of adjustments: FIG. B-Plantar/Dorsi-Loosen clamps to tilt foot plates. FIG. C-Adduction-Loosen clamps to slide foot plates together. FIG. D-Forward/Aft-Loosen knobs underneath foot plates, slide foot plates into position. FIG. D Forward/Aft FIG. E-Toe-in/Toe-out-Loosen knobs underneath foot plates, slide foot plates into position. FIG. F-Abduction-Loosen clamps to spread apart foot plates, tighten clamps. Loosen knobs under foot plates and slide foot plates apart. Always tighten knobs securely. Kneepads FIG. G-The standard knee pads have depth and pad rotation adjustments only. To adjust the kneepads, loosen the knobs and move into position. Tighten securely once desired position is reached. FIG. H-The Swing-Away Knee pads swing out of the way by depressing the red button, they also have width and height adjustments. FIG. E Toe-in/Toe-out FIG. F Abduction ! Caution: Make knee pad adjustments while child is in the seated position only. FIG. G FIG. H Standard Knee pads Swing-Away Knee pads Page 14 Adjustments & Usage Seat Depth/Back Angle/Back Height ! Caution: Do not adjust the seat depth while the child is in the Extra Small Small FIG. H unit. ! Caution: Ensure the colors on the seat tube and following arm match. First remove the Shadow Tray and bring the seat up to a slight angle. FIG. H-Loosen the knobs on the seat tube and the following arm. Do not unscrew knobs out all the way when adjusting the seat. The Bantam Extra Small back angle adjustments are located above the locking knob. The back angle adjustments go from green (largest) to blue (smallest). The Bantam Small back angle adjustments are located below the locking knob. The back angle adjustments go from blue (smallest) to green (largest). FIG. I-Adjusting to a shorter setting: Adjust the following arm (back angle) first by depressing the spring button and moving no more than two holes at a time. Then adjust the seat tube (seat depth) one hole at a time. Continue this sequence until you achieve the desired setting and the colors on the seat tube and following arm match. FIG. I Seat Tube Following Arm FIG. J FIG. K FIG. I-Adjusting to a longer setting: Adjust the seat tube (seat depth) first by depressing the spring button and moving only one hole at a time. Then adjust the following arm (back angle) no more than two holes at a time. Continue this sequence until you achieve the desired setting and the colors on the seat tube and following arm match. FIG. J-For easier adjustment, use the back bracket as a handle. You may need to lift slightly as the seat depth adjustment is made. FIG. L FIG. H-Tighten the seat depth and following arm knobs securely when you have achieved the desired position. FIG. K-To adjust back height, loosen knob and slide back into position. Tighten securely. FIG. M Shadow Tray Option ! Caution: These adjustments are only to be made while the unit is in the seated position. ! Caution: Always support the tray when loosening the ratchet handles to adjust the tray. ! Caution: After placing the tray into position, ensure the ratchet handles on the side of the tray are tightened securely. FIG. L-To adjust the depth of the optional tray, place tray tubes into the receptacles and line up holes to the desired depth, and insert pins. FIG. M-To adjust the height of the tray, loosen both ratchet handles and lift the tray to the user’s desired height, tighten securely. FIG. N-To adjust the angle of the tray, loosen both ratchet handles on the side of the tray and position the tray to the user’s desired angle, tighten securely. Page 15 Adjustments & Usage FIG. N Hip Supports/Lateral Supports Options FIG. O FIG. O-The optional hip supports can be removed for transferring. The hip support width can be adjusted by loosening the knobs underneath the seat. Loosen the knob on the side of the unit to adjust the hip support width. Always tighten securely. The hip supports have a number of attachment holes on the back of the pad allowing for additional positions vertically and horizontally. The pads can also be bolted on at a straight, 90º, 180º, or 270º position. Hip Supports FIG. P-The optional lateral supports can be removed for transferring. The lateral support width can be adjusted by loosening the knobs on the back of the unit. Always tighten securely. FIG. P The lateral supports have a number of attachment holes on the back of the pad allowing for additional positions vertically and horizontally. The pads can also be bolted on at a straight, 90º, 180º, or 270º position. Please check for fit and interference by bringing the unit to the maximum standing position and back to sitting again (without a user seated in the unit) as the pads may not work perfectly in all positions. Lateral Supports Accessories Mounting Bracket FIG. Q-The accessories mounting bracket is attached to the back of the unit and is used for a wide range of options. The holes in the middle can be used for many styles of aftermarket head supports. There are holes for the optional push handles, chest vests, chest straps, and lateral supports. This bracket is standard on all units. Push Handle Mounting Hole FIG. Q Chest Vest Top Mounting Hole Attaching the Chest Vest FIG. R-Insert chest vest clips into slots as shown with tab facing up. Headrest Mounting Holes Chest Vest Top Mounting Hole Push Handle Mounting Hole FIG. S-Once the tab is past the bracket, pull back until snug. FIG. R FIG. S Lateral Support Slot Chest Vest Bottom Mounting Hole Chest Vest Bottom Mounting Hole Lateral Support Slot Page 16 Adjustments & Usage Supine Option Usage Activating Supine Positioning 1. Loosen both red supine locking handles located by the hip pivot on both sides of the unit. Flip the supine lever located under the right side of the seat to the “supine” position. This will release the back, seat and foot plates from the frame. 2. Adjust to the desired supine position by tilting the back and then tighten both red supine locking handles. This can be done with the user in the stander and at any position. The Swing-Away front will need to be swung out of the way to reach a full supine position. 3. Depress the foot pedal (or optional hydraulic actuator) to position the stander at the desired standing angle. Flat to Load Transfers: Children who are difficult to transfer due to high tone can utilize the Bantam with the Supine option to do a flat-to-load transfer or a knee/hip flexion (with a slight bend at the knees and hips) transfer. Page 17 Supine Usage Videos on EasyStand Bantam assembly & fitting can be viewed at www.easystand.com/videos and click on “Bantam”. Returning to sit-to-stand position/deactivating the Supine Positioning 1. Flip the supine lever located under the right side of the seat to the “sit to stand” position. 2. Loosen the red locking handles. Handles must be loose for use in sit-to-stand position and tightened for use in supine position. Damage may occur if the handles are not loose when returning to the sit-to-stand position. 3. Push the back forward to connect the back, seat and foot plate to the frame. You should hear the supine lever click into place. This can be done with the user in the stander and at any position. Page 18 Supine Usage Pow’r Up Lift Option Usage Charging the Battery The EasyStand Bantam Pow’r Up Lift uses two 12 volt sealed lead batteries rated at 2.9 amps each. An EasyStand Bantam can be lifted approximately 100 times on one full battery charge. An audible alarm will sound when the battery is low. Please charge the battery after the alarm sounds. A battery needing a full recharge will take approximately 8 hours. The EasyStand Bantam can be raised to the standing position while being charged. The function of the charger is to detect a full battery and then provide a constant potential power supply to hold the battery at a full condition without overcharging. When the battery EMF rises to a factory preset point, the charger circuit will not allow the peak output voltage to exceed that value. This factory FIG. A setting protects a battery from excessive depletion of electrolyte, which can occur from overcharging. The charger can be found in the tool pouch on the back of the unit. ! CAUTION: Use only the Linak charger, model numbers 00CH01-XX OR 10CH01S-00, provided by Altimate Medical with your Pow’r Up option. 1. Plug the receptacle into a wall outlet. The light on the charger will be green indicating an open circuit. 2. FIG. A-Plug the charger cord into the side of the hand control. The light on the charger will turn yellow indicating the batteries are being charged. 3. FIG. B-The unit will arrive unplugged from the battery, you need to plug in the white cord that supplies power to the actuator and the black cord that supplies power to the remote. The black cord has a notch on it to orient the The hand pendant connector. Fully charge battery before use. is a Type BF applied Note: The white cord has a rubber washer on it, which makes it very sticky and part. sometimes will not get pushed in completely, make sure to push the cord all FIG. B the way into the battery. 4. When the batteries are charged, the light on the charger will turn green. 5. Fully charge the batteries every three months or less during periods of intermittent or non-use. ! CAUTION: The Bantam Pow’r Up Option is not designed for continuous use. Duty Cycle 5% Max, 1 min. / 19 min. Raising the Lift - Press the UP (arrow up) button on the hand control to lift the seat. Lowering the Lift - Press the DOWN (arrow down) button on the hand control to lower the seat. ! CAUTION: Ensure the cables are attached properly per the instructions for use. Do not allow the cables to drag on the floor or to catch on objects. Page 19 Pow’r Up Lift Option Assembly of the Hand Control FIG. C FIG. C-Remove hardware from hand control tube. FIG. D FIG. D-Insert hand control tube into the side of the unit. FIG. E FIG. E-Place washer onto the hand control tube. FIG. F FIG. F-Place nut onto hand control tube and tighten securely. Place black plastic button onto the end of the hand control knob. Page 20 Pow’r Up Lift Option Activating the Mechanical Emergency Release ! CAUTION: Using the emergency mechanical release as the primary means of returning to the seated position can cause damage to the unit. Only use the mechanical release in emergency situations. All Altimate Medical electric lift products are equipped with a mechanical release to be used in emergency situations. FIG. G FIG. G-The release allows the user to be lowered to a seated position in the unlikely occurrence of the battery losing charge while the user is in a standing position. The actuator only retracts if the release is pulled and there is weight on the seat. The release is located on the left side of the seat and is signified by a red tag with the word “EMERGENCY”. 1. To activate the emergency mechanical release pull out the quick release pin located underneath the seat. 2. Squeeze the handle and, if necessary, push down on the handle. Battery Replacement The batteries are enclosed in the control box of the Pow’r Up Lift (the black box where the cords are plugged in). Once the batteries have reached the end of their life and need to be replaced, do not open the control box; please contact Altimate Medical Customer Service or your medical equipment dealer for information about purchasing a replacement control box. It is recommended that the batteries be replaced every four years. Please contact your local recycling authority for information about disposing of the old batteries. IP Rating The IP rating is a classification system indicating the protection degree from dust, water and impact for electrical equipment and enclosures. Pow’r Up Lift components are rated at IP21. The definition for IP21 is as follows: First character definition: 2 - Protected against solid foreign objects of 12.5mm diameter and greater. Second character definition: 1 - Protected against vertically falling water drops. Electromagnetic compatibility Pow’r Up Option components have been designed and tested to meet the applicable EMC requirements. It is unlikely that you will encounter problems with your EasyStand due to inadequate electromagnetic compatibility. However, if you notice any unusual (such as intermittent) behavior of your Pow’r Up option and the EasyStand is being used next to possible interfering equipment such as mobile phones, microwaves, or radio broadcast masts, this could be an indication of electromagnetic interference. If such behavior occurs, use the mechanical release to lower the unit to the seated position and move the EasyStand away from the interfering equipment. Please report any instance of possible electromagnetic interference to Altimate Medical’s Customer Service Department. Page 21 Pow’r Up Lift Option Guidance and Manufacturer’s Declaration - Electromagnetic Emissions The EasyStand Bantam is intended for use in the electromagnetic environment specified below. The customer or the user of the EasyStand Bantam should assure that it is used in such an environment. Compliance Emissions Test RF emissions CISPR 11 Group 1 RF emissions CISPR 11 Class B Harmonic emissions IEC 61000-3-2 Class A Voltage fluctuations/ Flicker emissions IEC 61000-3-3 Complies Electromagnetic Environment - Guidance The EasyStand Bantam uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. The EasyStand Bantam is suitable for use in all establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Guidance and Manufacturer’s Declaration - Electromagnetic Immunity The EasyStand Bantam is intended for use in the electromagnetic environment specified below. The customer or the user of the EasyStand Bantam should assure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electrostatic Discharge (ESD) IEC 61000-4-2 ± 6 kV contact ± 8 kV air ± 6 kV contact ± 8 kV air Floors should be wood, concrete, or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%. Electrical Fast Transient/Burst IEC 61000-4-4 ± 2 kV for power supply lines ± 1 kV for input/ output lines ± 2 kV for power supply lines ± 1 kV for input/ output lines Mains power quality should be that of a typical commercial or hospital environment. Surge IEC 61000-4-5 ± 1 kV line(s) to line(s) ± 2 kV line(s) to earth ± 1 kV line(s) to line(s) ± 2 kV line(s) to earth Mains power quality should be that of a typical commercial or hospital environment. Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 <5 % UT (>95 % dip in UT) for 0,5 cycle 40 % UT (60 % dip in UT) for 5 cycles 70 % UT (30 % dip in UT) for 25 cycles <5 % UT (>95 % dip in UT) for 5 s <5 % UT (>95 % dip in UT) for 0,5 cycle 40 % UT (60 % dip in UT) for 5 cycles 70 % UT (30 % dip in UT) for 25 cycles <5 % UT (>95 % dip in UT) for 5 s Mains power quality should be that of a typical commercial or hospital environment. If the user of the EasyStand Bantam requires continued operation during power mains interruptions, it is recommended that the EasyStand Bantam be powered from an uninterruptible power supply or a battery. Power frequency (50/60 Hz) magnetic field IEC 61000-4-8 3 A/m 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. Electromagnetic Environment - Guidance NOTE: UT is the a.c. mains voltage prior to application of the test level. Page 22 Pow’r Up Lift Option Guidance and Manufacturer’s Declaration - Electromagnetic Immunity The EasyStand Bantam is intended for use in the electromagnetic environment specified below. The customer or the user of the EasyStand Bantam should assure that it is used in such an environment. Immunity Test IEC 60601 Test Level Compliance Level Electromagnetic Environment - Guidance Portable and mobile RF communications equipment should be used no closer to any part of the EasyStand Bantam, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance Conducted RF IEC 61000-4-6 3 Vrms 150 kHz to 80 MHz 3 Vrms d = 1.2 √P Radiated RF IEC 61000-4-3 3 V/m 80 MHz to 2.5 GHz 3 V/m d = 1.2 √P 80 MHz to 800 MHz d = 2.3 √P800 MHz to 2.5 GHz Where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in meters (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site surveya, should be less than the compliance level in each frequency range.b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the EasyStand Bantam is used exceeds the applicable RF compliance level above, the EasyStand Bantam should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or relocating the EasyStand Bantam. b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Page 23 Pow’r Up Lift Option Recommended separation distances between portable and mobile RF communications equipment and the EasyStand Bantam The EasyStand Bantam is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the EasyStand Bantam can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the EasyStand Bantam as recommended below, according to the maximum output power of the communications equipment. Rated maximum output power of transmitter W Separation distance according to frequency of transmitter m 150 kHz to 80 MHz d = 1.2 √P 80 MHz to 800 MHz d = 1.2 √P 800 MHz to 2.5 GHz d = 2.3 √P .12 .23 .12 0.01 .38 .73 .38 0.1 1.2 2.3 1.2 1 3.8 7.3 3.8 10 12 23 12 100 For transmitters rated at a maximum output power not listed above, the recommended separation distance d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects, and people. Page 24 Pow’r Up Lift Option EasyStand Bantam Parts Detail ® Page 25 Parts Detail Maintenance Cleaning/Disinfecting • • • • • • • • • • Clean the EasyStand Bantam with a mild, non-abrasive disinfectant or soap and water. Check the EasyStand at least weekly to ensure all nuts, bolts and adjustable parts are tightened securely, failure to do so may result in parts falling off which may cause a choking hazard for children. Do not use bleach or any other bleach-based cleaners on the EasyStand. Disinfecting wipes are safe to use on metal and non-porous surfaces. Use a damp sponge with mild soap or a mild, non-abrasive disinfectant. Spot clean Neoprene with mild soap and water. Neoprene covers may be removed and hand washed with water. Air dry the covers. Always use care when removing and replacing the covers. Do not dry clean any upholstery items. If the EasyStand is being used with one user, clean the EasyStand on a monthly basis or as needed. If the EasyStand is being used in a multiple user environment, the EasyStand should be cleaned after each use. Urethane Coated Fabrics (Dartex or generic equivalent) • The recommended cleaning and disinfection instructions should be followed whenever possible to avoid damage to the PU membrane which could lead to premature failure of the cover. • For superficial dirt, use a disposable wipe and a warm solution of neutral detergent. Do not use abrasive cleaners. • Disinfect using a 0.1% sodium hypochlorite solution (1000ppmm chlorine), stronger bleach solutions not recommended. • Thoroughly rinse any remaining cleaning solution with water and dry fabric before re-use or storage. • Do not iron. Hydraulic Actuator Maintenance • • • • • • • • • An initial break-in period of approximately 50-100 full cycles is normal for the hydraulic unit. You may experience a squeaking or a less-than-smooth forward stroke. The very close fit of its mating parts gives each actuator its own break-in “feel” and signature sound. If the actuator is leaking oil, call a local EasyStand supplier for a replacement. The serial number on the EasyStand will be needed. Do not exert excessive force on the actuator handle or use the actuator handle to move the EasyStand around. This may cause damage to the actuator handle and/or the actuator mechanism and will void any warranty. User maintenance is not required or recommended on the hydraulic actuator. Never apply lubricant, household oil, grease, or a similar product to any part of the unit. Some compounds may react with the seals used in the manufacture of this product. This may damage the unit and will void any warranty. Do not exceed the rated weight limit. If the EasyStand was shipped and exposed to a temperature of less than 50 degrees Fahrenheit, you must allow the hydraulic unit to warm to room temperature before use. Failure to follow this step could damage the unit and render it inoperable. Once a standing position is reached, the actuator may settle back one stroke, this is normal. It is not always necessary to push the actuator handle all the way back to lower the seat. If difficult to lower the seat, trypushing the handle back in different positions. If the unit is in the standing position and unoccupied, it is necessary to apply pressure to the seat of the unit while pushing the actuator handle back. Purging The Hydraulic Actuator The hydraulic actuator on the EasyStand has a high probability of getting air trapped in the internal workings of the unit. This is usually caused by in-transit handling and is quite normal. Please follow the simple steps below, as manual hydraulic systems may never operate properly unless the entrapped air is correctly purged. The unit must be at room temperature for this procedure. 1. Pump the handle until the full extension is reached. 2. Continue pumping the handle slowly for an additional 10 strokes. This will properly purge the system. Page 26 Maintenance TroubleShooting My lower leg length is too short for the stander. Invert and swap the foot plates left to right. My Bantam won’t go all the way to standing. Make sure that the supine option ratchet handles have been correctly assembled. We ship the back flat and the supine knob must be removed then assembled in the correct square hole. If not removed from position when shipped the bolt prevents the stander from going all the way up. Please refer to pg.6 in the owners manual. One of the arms on my tray is shorter than the other, is this correct? Yes, it is designed so you can line up the longer arm first, then the shorter arm. We just received our Bantam and on the tray there is a quick pin to secure the tray in place, but there are two bolts attached on both sides. Am I suppose to use the bolts to secure the tray in place? The bolts and nuts are used as a tray depth guide. You can move them to any one of the holes on the tray adjustment arm depending on the person using the unit. To use, remove from the tray, position the tray with the correct depth and then reinstall in the hole closest to the tray top. This will stop the arms at the correct depth so it is easier and quicker when attaching the tray. To secure the tray, there are two quick pins attached to cables on both sides of the unit. Check both sides to make sure both are there. Sometimes, in shipping, they will move around, so at first glance only one side is visible. How do I order parts? Contact your local supplier and have the serial number ready. If you don’t know who your supplier is, call Altimate Medical Customer Service (800) 342-8968 and have the serial number ready. Page 27 TroubleShooting Limited Warranty This warranty is extended only to the original purchaser/customer (or supplier non-consumer who does not buy or resell). Altimate Medical, Inc., warrants the EasyStand Bantam against defects in materials and workmanship as listed below. • • • • Steel Frames - 5 year warranty Gas Spring - 2 year warranty Hydraulic Actuator - 2 year warranty Upholstered components, plastic pads, rubber parts, painted surfaces, bearings and other parts not specifically identified above - 90 day warranty Warranty on Electric lift option components is as follows: • Actuator & Hand Pendant – 2 year warranty • Control Box & Battery – 90 days • Battery Charger – 90 days The warranty period commences for the consumer on the purchase date from the seller/supplier. If the product is rented or otherwise not sold to a consumer, the warranty period commences from the date of invoice from Altimate Medical. Any product proven to Altimate Medical satisfaction to be defective and within warranty period, shall be repaired or replaced at Altimate Medical’s option. ALTIMATE MEDICAL SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY SHALL BE LIMITED TO SUCH REPAIR AND/OR REPLACEMENT. This warranty does not include any labor charges incurred in replacement parts installation. Freight charges to factory are at the expense of consumer to seller. Return freight charges will be prepaid by Altimate Medical. For warranty service, please contact the authorized supplier from whom you purchased your Altimate Medical product. In the event you do not receive satisfactory warranty service, please write directly to Altimate Medical at the address below. Do not return products to our factory without prior authorization. LIMITATIONS AND EXCLUSIONS: The foregoing warranty shall not apply to serial numbered products if the serial number has been removed or defaced. Products subject to negligence, abuse, misuse, improper operation, improper maintenance, improper storage, or damages beyond Altimate Medical’s control are not covered by this warranty, and that evaluation will be solely determined by Altimate Medical. Products modified without Altimate Medical’s express written consent (including, but not limited to, modification through the use of unauthorized parts or attachments) are not covered by this warranty. The warranty shall not apply to problems arising from normal wear or failure to follow instructions. The warranty will be void if parts not manufactured by Altimate Medical or parts not complying with original equipment specifications are added to an Altimate Medical product. THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALTIMATE MEDICAL SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER. Altimate Medical maintains a policy of continual product improvement and reserves the right to change features, specifications, and prices without prior notification. Check with Altimate Medical for latest information. Altimate Medical, Inc., 262 W. 1st St., Morton, MN 56270 USA Phone: 507•697•6393 Fax: 507•697•6900 800•342•8968 www.easystand.com email@example.com Page 28 Warranty 262 West 1st St. Morton, MN 56270 USA Toll Free: 800.342.8968 or 507.697.6393 Fax Free: 877.342.8968 or 507.697.6900 email: firstname.lastname@example.org www.easystand.com Standing technology should only be used under the guidance of a physician with recommendations for standing program protocol and any medical precautions. Standing programs should be monitored by the attending therapist. AMI maintains a policy of continual product improvement and reserves the right to change features, specifications, and prices without prior notification. Check with AMI for latest info. FORM MBANEX-SMALL 012214 Copyright © 2014 Altimate Medical, Inc. All rights reserved. Printed in the U.S.A.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project