Quick Start Reference Guide - Accelerated Cooking Products

Quick Start Reference Guide - Accelerated Cooking Products
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
CLEAN FILTER
Complete Owner’s Manual available online
This oven displays CLEAN FILTER at user
defined intervals. When the message
displays Amana recommends cleaning
the air filter thoroughly. Cleaning the air
filter will not shut off the message.
The message will stop displaying
automatically after 24 hours. Depending
on microwave use and environmental
conditions, the filter may need to be
cleaned more frequently. Once the
frequency is determined, set the option
for the appropriate time frame.
Oven Wall Clearances
A—For North American (UL/CSA) models, allow at least 2” (5.1 cm)
of clearance around top of oven. For all international models
(50 Hz), allow at least 7” (18 cm) of clearance around the
top of the oven. Proper air flow around oven cools electrical
components. With restricted air flow, oven may not operate
properly and life of electrical parts is reduced.
B—There is not an installation clearance requirement for the back
of the oven.
C—Allow at least 1” (2.54 cm) of clearance around sides of oven.
D—Install combination oven so oven bottom is at least 3 feet (91.5
cm) above floor.
So...how do I use it?
Preprogrammed
Pads
To cook food using
preprogrammed cooking
sequences:
1. Open oven door and place food
in oven. Close door.
2. Press desired pad.
3. Oven begins to cook.
4. At end of cooking cycle oven
beeps and shuts off.
QTY 2X
Programming
(some models)
To change the cooking factor:
1. Open oven door.
2. Press and hold pad 1 for
approximately 5 seconds.
3. Press pad to be reprogrammed.
4. Press the QTY 2X pad.
5. Press a numbered pad to
change the cooking factor.
• Cooking factor can be set from
10% to 100%.
• Default is 80%.
• Pad 5 would change the
cooking factor to 50%.
6. Press START pad to save
changes.
(Electronic Control)
Manual Operation
To cook food using a specific entered time and power level:
1. Open oven door and place food in oven. Close door.
2. Press TIME ENTRY pad and enter cooking time.
3. Press a power level pad to change power level if desired (some
models).
• COOK LEVEL displays with the power setting.
4. If stage cooking is desired, press TIME ENTRY pad and repeat steps
2 through 4, (some models).
5. Press START pad.
6. At end of cooking cycle oven beeps and shuts off.
Programming Items
1.
2.
3.
4.
5.
6.
Open oven door.
Press and hold pad 1 for approximately 5 seconds.
Press pad to be reprogrammed.
Enter cooking time by using the number pads.
Press a power level pad to change power level if desired.
If stage cooking is desired, press TIME ENTRY pad.
• Display briefly shows the stage number.
• Display changes to cook time and power level for the next stage.
7. Enter cook time and power level as in steps 4 and 5 (some models).
• To enter another cooking stage for that pad, press TIME ENTRY pad
again.
• Up to four different stages can be programmed (some models).
8. Press START pad to set new programming changes to the pad.
NOTE: To discard changes, press STOP/RESET pad or close oven door.
QTY 2X Pad
1.
2.
3.
4.
(some models)
Open oven door and place food in oven. Close door.
Press QTY 2X pad.
Press desired preprogrammed pad or pad sequence.
Oven begins cooking. Displayed cooking time is the total of original
cooking time and added 2X time.
The switching operation of this microwave oven can cause voltage fluctuations on the supply line. The operation of this oven under
unfavorable voltage supply conditions can have adverse effects. This device is intended for the connection to a power supply system
with a maximum permissible system impedance Zmax of 0.2 Ohms at the interface point of the user’s supply. The user has to
ensure that this device is connected only to a power supply system which fulfills the requirement above. If necessary, the user
can ask the public power supply company for the system impedance at the interface point.
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
Complete Owner’s Manual available online
Cooking Instructions
1.
Cooking Vessels
a)
Always heat or cook food items in covered containers to accomplish:
•
Retention of steam for efficient cooking and to keep foods moist
•
Even cooking results and temperatures
•
A cleaner oven interior and prevention of food splatters
b)
Ceramic, paper, china, styrofoam, glass and plastic are suitable materials for use in microwave ovens.
A high temperature resistant amber pan is recommended for ALL items, especially those high in fat or sugar content, as these ingredients get hot very quickly.
2.
Food Temperature
a)
To reach a mandatory serving temperature, frozen foods require a longer cook time than refrigerated items.
b)
Refrigerated items:
•
Items stored at 40°F (4°C) in the refrigerator should be covered while heated; except breads, pastries or any products with a breaded coating, which should be heated uncovered to avoid softening.
c)
Room temperature items:
•
Foods held at room temperature, such as canned items or vegetables, will require less time to heat than refrigerated items.
d)
Conventionally prepared foods should be slightly undercooked to prevent overcooking when rethermed by microwave steaming.
e)
After a steaming cycle has been completed, internal food temperatures continue to slightly rise due to the presence of steam.
3.
Structure of Food
a)
Food items that are high in fat, sugar, salt and moisture attract and quickly absorb microwave energy, allowing for a shorter cook time.
b)
Items high in protein or fiber require a longer cook time, due to a slower absorption of microwave energy.
4.Quantity
a)
As the mass of food increases, so will the necessary cook time.
Refer to and comply with all USDA/FDA Food Code guidelines when cooking or heating food items.
Quick Start Reference Guide
Refer to Product Safety Manual for Safety Statements
Complete Owner’s Manual available online
Can I change an option?
Options such as single or double pad programming, beep volume, and
maximum cooking time can be changed to suit individual preferences.
To change options:
1. Open oven door.
• If door is closed or RESET pad is pressed before programming is complete,
changes are discarded and microwave exits programming mode.
2. Press and hold pad 2 for approximately 5 seconds.
• This begins options mode.
• Microwave will beep and 0P: displays.
3. Press number pad that controls option to be changed.
• See table below for options.
• Current option will display.
4. Press number pad again to change the option.
• Each time pad is pressed, option will change.
• Match code displayed with code for desired option.
5. Press START pad to save changes.
• To change additional options, repeat steps 3 and 4.
• Changes appear after door is closed or STOP/RESET pad is pressed.
DO NOT power spray
No metal pans
Numbered Pads
1
End of Cycle Beep
2
Speaker Volume
3
Key Beep
4
Keyboard Enable
Window
5
Add Time During
Heating
6
Reset Door Open
7
(some models)
Display
Options (Factory Settings in Bold)
OP:10
3 second beep.
OP:11
Continuous beep until door is opened.
OP:12
5 beep bursts until door is opened.
OP:20
Eliminates beep.
OP:21
Sets volume to low.
OP:22
Sets volume to medium.
OP:23
Sets volume to high.
OP:30
Prevents beep when pad is pressed.
OP:31
Allows beep when pad is pressed.
OP:40
15 seconds after oven door is opened, keyboard disabled.
OP:41
30 seconds after oven door is opened, keyboard disabled.
OP:42
1 minute after oven door is opened, keyboard disabled.
OP:43
2 minutes after oven door is opened, keyboard disabled.
OP:50
Prevents adding heating time while oven is heating.
OP:51
Allows heating time to be changed while oven is heating when a memory pad
is pressed.
OP:60
Allows oven to resume heating time countdown after door is opened during
cycle.
OP:61
Cancels heating time count down after door is opened during cycle.
OP:70
Allows 60 minutes of heating time (some models).
OP:71
Allows 10 minutes of heating time.
Maximum Heating Time
8
Manual Operation
9
(some models)
OP:80
Allows use of preprogrammed pads only.
OP:81
Allows use of manual time entry and preprogrammed pads.
OP:90
Allows 10 (0-9) preprogrammed pads.
OP:91
Allows 100 (00-99) preprogrammed pads.
Double Digit Operation
0
Clean Filter Message
Part No.12804410
Revised 6/16
OP:00
Do not display message.
OP:01
Display message for 24 hours every 7 days.
OP:02
Display message for 24 hours every 30 days.
OP:03
Display message for 24 hours every 90 days.
For full product documentation visit:
www.amanacommercial.com
 2016 ACP , Inc.
Cedar Rapids, Iowa 52404
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising