RS2314K.3 - Supercheap Auto

18V CORDLESS DRILL
RS2314K.3
EN
RS2314K.3
1
2
9
3
8
7
6
5
4
A2
B1
6
5
RS2314K.3
A1
A2
4
B1
REVERSE
B2
C
D
E1
E2
F
G
FORWARD
18V CORDLESS DRILL
EN
COMPONENT LIST
.
1
KEYLESS CHUCK
2
TORQUE ADJUSTMENT RING
3
FORWARD/REVERSE ROTATION CONTROL
4
BATTERY PACK
5
DOUBLE-ENDED BIT
6
BATTERY PACK RELEASE BUTTON
7
MAGNETIC TRAY
8
ON/OFF SWITCH
9
SIGHT LIGHT
Not all the accessories illustrated or described are included in standard delivery.
ACCESSORIES
1.3Ah Li-Ion battery pack
3-5hrs charger
Double ended bits
1
1
2
Use good quality accessories marked with a
well-known brand name. Choose the type according
to the work you intend to undertake. Refer to the
accessory packaging for further details. Store
personnel can assist you and offer advice.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or batteryoperated (cordless) power tool.
4
1. WORK AREA SAFETY
a) Keep your work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
2. ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
18V CORDLESS DRILL
EN
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
a cord suitable for outdoor use reduces the risk of
electric shock.
f) Recommendation for the use of a residual
current device with a rated residual current of
30 mA or less.
3. PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove adjusting keys or wrench before
turning the tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust-related hazards.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use of
the power tool for operations different from those
intended could result in a hazardous situation.
5. BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
5
18V CORDLESS DRILL
that can make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
6. SERVICE
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that that safety of the
power tool is maintained.
ADDITIONAL SAFETY POINTS FOR
YOUR BATTERY OPERATED DRILLS
& IMPACT DRILL
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Hold power tool by insulated gripping surfaces,
when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
General Safety Warnings for your Battery Charger
WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
- This appliance is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use
of the appliance by a person responsible for their
safety.
- Children should be supervised to ensure that they
do not play with the appliance.
Additional safety instructions for your Battery
Charger
1. Before charging, read the instructions.
6
EN
2. For charge Li-ion battery pack only.
3. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
4. The battery terminal not connected to the chassis
has to be connected first. The other connection is
to be made to the chassis, remote from the battery
and fuel line. The battery charger is then to be
connected to the supply mains.
5. After charging, disconnect the battery charger
from the supply mains. Then remove the chassis
connection and then the battery connection.
6. Do not charge a leaking battery.
7. Do not use chargers for works other than those for
which they are designed.
8. Before charging, ensure your charger is matching
the local AC supply.
9. The charging device must be protected from
moisture.
10.Do not use the charging device in the open.
11. Do not short out the contacts of battery or
charger.
12.Respect the polarity “+/-“ when charging.
13.Do not open the unit and keep out of the reach of
children.
14.Do not charge the batteries of other manufactures
or ill-suited models.
15.Ensure that the connection between the battery
charger and battery is correctly positioned and is
not obstructed by foreign bodies.
16.Keep battery charger’s slots are free of foreign
objects and protect against dirt and humidity.
Store in a dry and frost-free place.
17. When charging batteries, ensure that the battery
charger is in a well-ventilated area and away from
inflammable materials. Batteries can get hot
during charging. Do not overcharge any batteries.
Ensure that batteries and chargers are not left
unsupervised during charging.
18.Do not recharge non-rechargeable batteries, as
they can overheat and break.
19.Longer life and better performance can be
obtained if the battery pack is charged when the
air temperature is between 18oC and 24oC. Do not
charge the battery pack in air temperatures below
4.5oC, or above 40.5oC. This is important as it can
prevent serious damage to the battery pack.
20.Charge only battery pack of the same model
provided by manufacturer and of models
recommended by manufacturer.
18V CORDLESS DRILL
SAFETY WARNINGS FOR BATTERY
PACK
a) Do not dismantle, open or shred cells or battery
pack.
b) Do not short-circuit a battery pack. Do not store
battery packs haphazardly in a box or drawer
where they may short-circuit each other or be
short-circuited by conductive materials. When
battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
c) Do not expose battery pack to heat or fire. Avoid
storage in direct sunlight.
d) Do not subject battery pack to mechanical
shock.
e) In the event of battery leaking, do not allow the
liquid to come into contact with the skin or eyes.
If contact has been made, wash the affected
area with copious amounts of water and seek
medical advice.
f) Seek medical advice immediately if a cell or
battery pack has been swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with a clean
dry cloth if they become dirty.
i) Battery pack needs to be charged before use.
Always refer to this instruction and use the
correct charging procedure.
j) Do not maintain battery pack on charge when
not in use.
k) After extended periods of storage, it may
be necessary to charge and discharge the
battery pack several times to obtain maximum
performance.
l) Battery pack gives its best performance when it
is operated at normal room temperature (20 °C
± 5 °C).
m) When disposing of battery packs, keep battery
packs of different electrochemical systems
separate from each other.
n) Recharge only with the charger specified by
manufacturer. Do not use any charger other
than that specifically provided for use with the
equipment. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
o) Do not use any battery pack which is not
designed for use with the equipment.
p) Keep battery pack out of the reach of children.
EN
q) Retain the original product literature for future
reference.
r) Remove the battery from the equipment when
not in use.
s) Dispose of properly.
7
18V CORDLESS DRILL
EN
SYMBOLS
To reduce the risk of injury, user must read in struction manual
Warning
Wear ear protection
Wear eye protection
Wear dust mask
C-Tick approval mark
Li-I on
Li-Ion
Li-Ion battery. This product has been
marked with a symbol relating to ‘separate
collection’ for all battery packs and
battery pack. It will then be recycled or
dismantled in order to reduce the impact
on the environment. Battery packs can
be hazardous for the environment and
for human health since they contain
hazardous substances.
Do not burn
Batteries may enter water cycle if
disposed improperly, which can be
hazardous for ecosystem. Do not dispose
of waste batteries as unsorted municipal
waste.
xINR18/65-y: Cylindrical lithium Ion
battery cells with max diameter of 18mm
and max height of 65mm; “x” represents
a number cells serial connected, blank
if 1; “-y” represents a number of cells
paralleled connected, blank if 1.
8
For indoor use only
Positive terminal
Negative terminal
The output plug is with positive center pole and negative outer pole
18V CORDLESS DRILL
TECHNICAL DATA
Voltage
Charger voltage
No load speed
Clutch position
Max. torque
Chuck capacity
Max. drilling capacity
Wood
Steel
Battery capacity
Charging time
Machine weight
EN
18V
100-240V~50Hz
0-550/min
16+1
18N.m
10mm
18mm
8mm
1.3Ah Li-Ion
3-5hrs
1.5kg
CHARGING PROCEDURE
NOTE: Before using the tool, read the
instruction book carefully.
Intended Use
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal, and
plastic.
1. CHARGING YOUR BATTERY PACK
a) CHARGING THE BATTERY
The battery charger supplied is matched to the Li-Ion
battery installed in the machine. Do not use another
battery charger.
The Li-Ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit: The
tool holder no longer rotates.
In a warm environment or after heavy use, the battery
pack may become too hot. Allow time for the battery
to cool down before recharging.
b) IMPORTANT NOTES FOR CHARGING THE BATTERY
The battery in your new tool is not charged when it
leaves the plant. Therefore it must be charged for 1
hours before using the first time!
NOTE: If the battery pack is very hot you must remove
your battery pack from the charger and allow your
battery pack to cool first to ambient temperature and
then recharging can be started.
To prevent damage to the Battery Pack, when charge
runs out, please charge the battery to reach full or no
less than half charge before storage.
If the tool will not be used for long periods of time,
charge the battery every 3-6 months.
2. HOW TO CHARGE YOUR BATTERY (See Fig. A1, A2)
Connect the battery charger to the power supply, and
then plug the DC socket of charger in to charger base
,and the light is green. Then slide the battery pack into
the charger base to make the connections. And the
green light will turn red to show charging has started.
After charging approx 3-5 hours, the red light will turn
green which means the battery is full, and charging is
completed. Then slide the battery from your charger.
NOTE: This charger is designed to detect some problems
that can arise with battery pack. (See table below)
Light
Status
Charger is plugged
Green ON into the socket without
the battery inserted.
Red ON
Charging
Red OFF
Fully charged
Green ON
Measure
________
Red OFF
Green ON
Charging battery
too hot
Let the hot battery
cool down for a
while.
Red OFF
Green ON
Defective battery
Change a new
battery.
3. TO REMOVE OR INSTALL THE BATTERY PACK
(See Fig. B1,B2)
Depress the battery pack release button to release
and slide the battery pack out from your tool. After
recharge, slide it back into your tool. A simple push
and slight pressure will be sufficient.
OPERATING INSTRUCTIONS
1. ON/OFF SWITCH (See Fig. C)
Depress the On/Off switch to start and release it to
stop your drill. The on/off switch is fitted with a brake
function which stops your chuck immediately when
you quickly release the switch.
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
WARNING: Do not operate for long periods at low
speed because excess heat will be produced
internally.
9
18V CORDLESS DRILL
2. SWITCH LOCK (See Fig. D)
The On/Off switch trigger can be locked in OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
switch, place the forward /reverse rotation control in
the center position by pushing it on either side of the
drill.
Fig D: the forward /reverse rotation control is in the
center position.
3. REVERSIBLE (See Fig. E1, E2)
For drilling and screw driving use forward rotation
marked “
” (lever is moved to the left). Only
use reverse rotation marked “
” (lever is
moved to the right) to remove screws or release a
jammed drill bit.
WARNING: Never change the direction of
rotation when the chuck is rotating, wait until
it has stopped !
4. CHUCK ADJUSTMENT (See Fig. F)
To open the chuck jaws rotate the front section of
the chuck. Insert the drill bit between the chuck jaws
and rotate the front section in the opposite direction.
Ensure the drill bit is in the center of the chuck jaws.
Finally, firmly rotate the front chuck section in the
opposite directions. Your drill bit is now clamped in
the chuck.
5. TORQUE ADJUSTMENT (See Fig. G)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when the
torque adjustment ring is set on a higher setting. The
torque is less when the torque adjustment ring is set
on a lower setting.
Make the setting as follows:
1 - 3 for driving small screws
4 - 6 for driving screws into soft material
7 - 9 for driving screws into soft and hard material
10 - 12 for driving screws into hard wood
13 - 16 for driving larger screws
for heavy drilling
6. SIGHT LIGHT
The sight light allows you to keep a clear view under
less illuminated circumstances. To turn on the light
10
EN
simply press the on/off switch. When you release the
on/off switch, the light will be off.
7. DRILLING
When drilling into a hard smooth surface, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off center as the
hole is started. Hold the tool firmly and place the tip
of the bit at the point to be drilled. Depress the switch
trigger to start the tool. Move the drill bit into the
workpiece, applying only enough pressure to keep
the bit cutting. Do not force or apply side pressure to
elongate a hole.
When drilling in metal, only use HSS drill bits
in good condition. When screw-driving, apply
a small quantity of liquid soap or similar to the
screw threads to ease insertion.
8. DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle
or dispose of the battery pack properly.
Li-Ion This battery pack contains lithium batteries.
Consult your local waste authority for information
regarding available recycling and/or disposal options.
Discharge your battery pack by operating your drill,
then remove the battery pack from the drill housing
and cover the battery pack connections with heavy
duty adhesive tape to prevent short circuit and energy
discharge. Do not attempt to open or remove any of
the components.
9. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop. Release
the on/off button, and the machine will restart
immediately.
10. TEMPERATURE DEPENDENT OVERLOAD PROTECTION
When using as intended for the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature of 75°C is exceeded,
the electronic control switches off the power tool until
the temperature is in the optimum temperature range
again.
11. PROTECTION AGAINST DEEP DISCHARGING
The Li-Ion battery is protected against deep
discharging by the “Discharging Protection System”.
When the battery is empty, the machine is switched
off by means of a protective circuit: The inserted tool
no longer rotates.
18V CORDLESS DRILL
EN
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN YOU PRESS
THE SWITCH?
The forward/reverse rotation control, which is on
top of the trigger, is positioned in the lock function.
Unlock the forward/reverse rotation control by putting
it into the required rotation position. Push the trigger
and the drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS COMPLETELY
TIGHTENED. WHY?
Verify the torque position of the variable clutch, you
can find the variable clutch between the chuck and
the drill body. Position 1 is the lowest torque (screw
driving force) and position 16 is the highest torque
(screw driving force). Position 17 is for drill operation.
Regulate the variable clutch to a higher position to
reach the best result.
3. I CANNOT FIT THE BATTERY INTO THE BATTERY
CHARGER. WHY?
The battery can be inserted into the charger only in
one direction. Turn the battery around until it can be
inserted into the slot.
4. REASONS FOR DIFFERENT BATTERY PACK WORKING TIMES
Charging time issues, as above, and having not used
a battery pack for a prolonged time will reduce the
working life of the battery pack. This can be corrected
after several charge and discharge operations by
charging & working with your drill. Heavy working
conditions such as large screws into hard wood will
use up the battery pack energy faster than lighter
working conditions. Do not re-charge your battery
pack below 0oC and above 45oC as this will affect
performance.
MAINTENANCE
Your power tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage
your power tool.
Staple your purchase receipt here
Before returning this product for
warranty or any other reason, please call.
POSITEC AUSTRALIA PTY LIMITED
ABN 14 101 682 357
Unit 15, 23 Narabang Way Belrose 2085 NSW
Australia
FREE CALL 1300 889 028
EMAIL:[email protected]
11
Copyright © 2014, Positec. All Rights Reserved.
2SDT090PK11000A0
MADE IN PRC

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project