Wilo DrainLift WS 40 Basic, WS 40-50 Sewage Lifting Unit Einbau- und Betriebsanleitung

2 532 145-Ed.01/2010-06-Wilo
Wilo-DrainLift WS 40 Basic, WS 40-50
D
Einbau- und Betriebsanleitung
I
Istruzioni di montaggio, uso e manutenzione
GB
Installation and operating instructions
H
Beépítési és üzemeltetési utasítás
F
Notice de montage et de mise en service
RUS Инструкция по монтажу и эксплуатации
Fig. 1: WS 40-50 E
240
Ø570
370
Ø63
75
120
785
1042
L
D
H
1000
Ø75
Ø50
120
120
220
800
300
600
650
Fig. 2: WS 40-50 D
350
120
Ø570
125
360
L
D
Ø63
350
1042
Ø50
D
H
770
1000
Ø75
120
L
1000
355
765
800
300
50
Fig. 3: WS 40 E/TC 40 BV (Basic)
Fig. 5: WS 50 E/TP 65
Fig. 4: WS 40 E/MTS 40
Fig. 6:
7
8
6
10
4
9
3
1
5
2
2
12
11
Fig. 7:
8
50
13
6
9
D
Einbau- und Betriebsanleitung
3
GB
Installation and operating instructions
19
F
Notice de montage et de mise en service
35
I
Istruzioni di montaggio, uso e manutenzione
53
H
Beépítési és üzemeltetési utasítás
70
RUS
Инструкция по монтажу и эксплуатации
86
English
1 General
Installation
and operating instructions
About this document
The language of the original operating instructions is German. All other languages of these
instructions are translations of the original operating instructions.
These installation and operating instructions are an integral part of the product. They must
be kept readily available at the place where the product is installed. Strict adherence to
these instructions is a precondition for the proper use and correct operation of the product.
These installation and operating instructions correspond to the relevant version of the
product and the underlying safety standards valid at the time of going to print.
EC declaration of conformity:
A copy of the EC declaration of conformity is a component of these operating instructions.
If a technical modification is made on the designs named there without our agreement, this
declaration loses its validity.
2 Safety
These operating instructions contain basic information which must be adhered to during
installation and operation. For this reason, these operating instructions must, without fail,
be read by the service technician and the responsible operator before installation and
commissioning.
It is not only the general safety instructions listed under the main point “safety” that must
be adhered to but also the special safety instructions with danger symbols included under
the following main points.
2.1 Indication of instructions in the operating instructions
Symbols:
General danger symbol
Danger due to electrical voltage
NOTE
Signal words:
DANGER!
Acutely dangerous situation
Non-observance results in death or the most serious of injuries.
WARNING!
The user can suffer (serious) injuries. “Warning” implies that (serious) injury to persons
is probable if this information is disregarded.
CAUTION!
There is a risk of damaging the product/unit. “Caution” implies that damage to the
product is likely if this information is disregarded.
NOTE: Useful information on handling the product. It draws attention to possible problems.
2.2 Personnel qualifications
The installation personnel must have the appropriate qualifications for this work.
2.3 Danger in the event of non-observance of the safety instructions
Non-observance of the safety instructions can result in risk of injury to persons and damage to the product/unit. Non-observance of the safety instructions can result in the loss of
any claims to damages.
In detail, non-observance can, for example, result in the following risks:
• failure of important product/unit functions,
• failure of required maintenance and repair procedures,
• danger to persons from electrical, mechanical and bacteriological influences,
• property damage.
Installation and operating instructions Wilo-DrainLift WS 40-50
19
English
2.4 Safety instructions for the operator
The existing directives for accident prevention must be adhered to.
Danger from electrical current must be eliminated. Local directives or general directives
[e.g. IEC, VDE etc.] and local energy supply companies must be adhered to.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
2.5 Safety instructions for inspection and installation work
The operator must ensure that all inspection and installation work is carried out by authorised and qualified personnel, who are sufficiently informed from their own detailed study
of the operating instructions.
Work on the product/unit must only be carried out when at a standstill. It is mandatory that
the procedure described in the installation and operating instructions for shutting down
the product/unit be complied with.
2.6 Unauthorised modification and manufacture of spare parts
Modifications to the product are only permissible after consultation with the manufacturer. Original spare parts and accessories authorised by the manufacturer ensure safety.
The use of other parts can nullify the liability from the results of their usage.
2.7 Improper use
The operating safety of the supplied product is only guaranteed for conventional use in
accordance with Section 4 of the operating instructions. The limit values must on no
account fall under or exceed those specified in the catalogue/data sheet.
3 Transport and interim storage
•
•
•
•
•
The system and individual components are delivered on a pallet.
Immediately after receiving the product:
Check product for transport damage.
In the event of damage in transit, take the necessary steps with the forwarding agent
within the respective time limits.
WARNING! Risk of injury!
Improperly securing the load during transport and interim storage of the product can
lead to personal injury.
During transport, make sure the product is stable.
CAUTION! Risk of damage!
Incorrect transport and interim storage can cause damage to the product.
Only transport the product on the pallet and only use approved handling equipment.
During transport, check for stability and avoid mechanical damage.
Prior to installation, store the product on the pallet so that it remains dry and is protected from the sun.
4 Intended use
The DrainLift WS 40-50 sewage lifting unit is an automatic sewage lifting unit according
to EN 12050 for collecting and pumping sewage which is free of faeces or which contains
faeces for the backflow-proof drainage from building discharge points and properties
below the backflow level.
Here, the unit can both be installed and operated in the building as well as outside of the
building as an underground pumps station.
Sewage (grey water) which is free of faeces or rainwater, or for some pump types, sewage
containing faeces from the domestic area, may be introduced in accordance with
EN 12056-1.
20
WILO SE 06/2010
English
The correspondingly marked unit types in the tables under 5.4.1 and 5.4.2 comply with
EN 12050-1 and are therefore suitable for pumping sewage containing faeces.
No explosive or harmful substances may be introduced in high concentrations, such as
solid substances, debris, ashes, garbage, sand, plaster, cement, lime, mortar, fibrous materials, textiles, paper towels, diapers, cardboard, coarse paper, synthetic resins, tar, kitchen
waste, greases, oils, slaughterhouse waste, disposal of slaughtered animals and animal
waste (liquid manure, etc.), toxic, aggressive and corrosive substances, such as heavy metals, biocides, pesticides, acids, bases, salts, cleaning agents and disinfectants, dish-washing or laundry detergents, and such which have a high degree of foam formation or
swimming-pool water.
If greasy sewage should accumulate, a grease trap is to be installed.
According to EN 12056-1, no sewage from drainage objects may be introduced which lie
above the backflow level and can be drained by means of gravity.
NOTE: During installation and operation, be sure to observe the nationally and regionally
valid standards and regulations.
The specifications in the operating instructions of the switchgear are also to be observed.
DANGER! Risk of explosion!
Sewage containing faeces in collection reservoirs can lead to gas accumulation, which
can ignite as a result of improper installation and operation.
• If the unit is used for sewage containing faeces, the valid regulations for potentially
explosive areas are to be observed.
WARNING! Health hazard!
Due to the used materials, the sewage lifting unit is not suitable for pumping potable
water! Contact with sewage poses a health hazard.
CAUTION! Risk of damage!
Inappropriate materials in the system can cause damage to the product.
• Never introduce solids, fibrous substances, tar, sand, cement, ash, coarse paper, paper
towels, cardboard, debris, rubbish, animal waste, grease, or oil into the drains!
If greasy sewage should accumulate, a grease trap is to be installed.
• Improper use and overstraining lead to material damage to the product.
The maximum possible inflow must always be less than the volume flow of a pump at
the respective duty point.
Application limits
The unit is not designed for permanent operation!
The specified maximum volume flow applies for intermittent operation (S3 – 15 %).
WARNING! Risk of burns!
Depending on the operating status of the installation, the entire pump can become very
hot. Touching the pump can cause burns.
WARNING! Danger due to overpressure!
If the lowest suction head is more than 5 m, this will cause overpressure in the reservoir
should the unit malfunction. If this happens, there is a risk that the reservoir will burst.
In case of malfunctions, the inlet must be blocked off immediately!
The intended use includes complying with these instructions.
Any use going over and beyond the intended use is considered to be improper.
Installation and operating instructions Wilo-DrainLift WS 40-50
21
English
5 Product information
5.1 Type key
Example:
WS 40 E/TC 40 (1~) BV
WS 40 D/MTS 40
WS
40
S
Series: Wilo pumps station Synthetic
Nominal diameter of the pressure pipe [mm] 40, 50
E = Single-pump system
D = Double-pump system
Selected pump type:
WS 40 with TC 40, MTS 40
WS 50 with TP 50, TP 65
1~: Single-phase version
3~: Three-phase version
Version with non-return ball valve
TC 40
(1~)
BV
5.2
Technical data
Operating mode
Maximum inlet:
Maximum cover load, short-term:
Max. admissible pressure in the
pressure pipe:
Discharge pipe connection
Inlet connection
Bleeding connection
Cable conduit connection
Max. permissible
fluid temperature:
Comments
S3 – 15%
15% of the pump
volume flow
200 kg
6 bar
DN 40/DN 50
DN 100/DN 150
DN 70
DN 50
40 °C
35 °C
Max. permissible
ambient temperature:
Max. permissible
ball passage
Max. permissible
ground water level (from the bottom
edge of the reservoir):
Of one pump at the duty point
For ground installation
1.5 bar for WS 40 Basic
Depends on pump
WS 40 Basic 60 °C permissible for
max. 3 min.
In connection with pump
MTS 40, TP 50, TP 65
40 °C
40 mm
See data sheet/
catalogue
500 mm
1000 mm
Version WS 40 Basic only
Depends on pump for WS 40-50
With sump length extension for
single-pump stations only
5.3 Dimensions
For main dimensions [mm], see:
• Fig. 1: Single-pump station
• Fig. 2: Double-pump station
Total volume [l]
with extension
Unit height [mm]
with extension
H [mm]
L [mm]
D
22
WS 40 Basic with pump
WS 40 for pump
WS 50 for pump
TC 40 BV
MTS 40/...
TP 50, TP 65
Single
255
325
1040
1340
770
100/75
Ø 50/G 2
Double
400
470
1040
1340
770
100/75
Ø 50/G 2
Single
255
325
1040
1340
735
95
G1½
Double
400
470
1040
1340
745
100
G1½
Single
255
325
1040
1340
735
65
G2
Double
400
470
1040
1340
745
75
G2
WILO SE 06/2010
English
5.4 Versions
For information regarding the current and power consumption P1: see rating plate of the
pump
5.4.1 Version WS 40 Basic (pump built-in)
Sewage lifting unit complies with DIN EN 12050-2 (sewage free of faeces)
Type
Voltage
[V]
Switchgear
Level measurement
WS 40E/TC 40 (1~)-BV
WS 40E/TC 40 (3~)-BV
WS 40D/TC 40 (1~)-BV
WS 40D/TC 40 (3~)-BV
1~230
3~400
1~230
3~400
EC-Drain
PL2-WS(1~)
PL2-WS(3~)
Float switch
• = available
Alarm signal
mains-dependent
•
•
Level sensor
•
– = not available
5.4.2 Version WS 40-50 (pump must be ordered separately)
Sewage lifting unit complies with DIN EN 12050-1 (sewage containing faeces)
• Pump TP 50, TP 65: only for using TP 50F-0,75 and TP 65F
• Pump MTS 40: also permissible in accordance with DIN EN 12050-1
Type
WS 40E/
WS 40D/
WS 50E/
WS 50D/
Usable
Voltage
Pump
[V]
MTS 40
MTS 40
MTS 40
MTS 40
TP 50, TP 65
TP 50, TP 65
TP 50, TP 65
TP 50, TP 65
1~230
3~400
1~230
3~400
1~230
3~400
1~230
3~400
Switchgear
Level measurement Alarm signal
(to be ordered separately)
PL1-WS(1~)
PL1-WS(3~)
PL2-WS(1~)
PL2-WS(3~)
PL1-WS(1~)
PL1-WS(3~)
PL2-WS(1~)
PL2-WS(3~)
Mains-dependent
•
•
•
•
Level sensor
•
•
•
•
• = available
CE conformity
CE conformity
WILO
05
WILO
05
EN 12050-2
Sewage lifting unit for sewage free of faeces
DN 40, DN 50
Lifting power - see pump curve
Noise level – NPD
Corrosion protection – inox/composite corrosion-resistant materials
EN 12050-1
Sewage lifting unit for sewage containing faeces
DN 40, DN 50
Lifting power - see pump curve
Noise level – NPD
Corrosion protection – inox/composite corrosion-resistant materials
Please state all the information on the unit rating plate when ordering spare parts.
5.5 Scope of delivery
•
•
•
•
•
•
WS 40 Basic
Sewage lifting unit WS 40 ..., comprising PE reservoir and built-in pipework, including nonreturn valve, clamp bolting on the pressure side, built-in pump, shut-off ball cock (PVC),
level measurement as well as an external switchgear, depending on the pump and unit type
(see table under 5.4.1).
1 reservoir cover with gasket
1 keyhole saw Ø 124
1 inlet gasket DN 100 (for pipe Ø 110 mm)
1 hose section PVC Ø 50 mm with clamps for diaphragm hand pump connection
Fixation material
Installation and operating instructions
Installation and operating instructions Wilo-DrainLift WS 40-50
23
English
•
•
•
•
•
•
•
WS 40-50
Sewage lifting unit WS 40-50 ..., comprising PE reservoir with installed stainless steel pipework, red brass gate valve, surface coupling (PUR) with built-in non-return ball valve.
1 reservoir cover with gasket
1 keyhole saw Ø 124
1 inlet gasket DN 100 (for pipe Ø 110 mm)
1 hose section PVC Ø 50 mm with clamps for diaphragm hand pump connection
Pump(s), switchgear and level control according to order (see table under 5.4.2)
Fixation material
Installation and operating instructions
5.6 Accessories
Order accessories separately (see also catalogue/price list)!
The following accessories are available:
General accessories
Sump length extension, 300 mm, with gasket
Inlet gasket KIT (gasket for pipe Ø 110 mm with keyhole saw)
Inlet gasket KIT (gasket for pipe Ø 160 mm with keyhole saw)
Gate valve inlet DN 100 made of plastic
Gate valve inlet DN 150 made of plastic
Diaphragm hand pump (R 1½) (without hose)
Breakdown barrier (Zener barrier) in the housing with connecting cable for the use of a level
sensor in potentially explosive areas.
• Ex-rated cut-off relay for the use of float switches in potentially explosive areas
• Alarm switchgear
• Float switch for alarm signal
•
•
•
•
•
•
•
Accessories specifically for version WS 40 Basic:
• Clamp bolting for connection to PE discharge pipe (onsite)
• 2" (female thread) on 63 mm outer Ø
• Gate valve pressure pipe(s)
• Gate valve 1½"
• Gate valve 2"
Accessories specifically for version WS 40-50:
Clamp bolting for connection to PE discharge pipe (onsite)
• Unit type WS 40:
• 1½" (female thread) on outer Ø 50 mm
• 1½" (female thread) on outer Ø 63 mm
• Unit type WS 50:
• 2" (female thread) on outer Ø 63 mm
• 2" (female thread) on outer Ø 75 mm
• Vacuum interrupter 1"
6 Description and function
6.1 Description
The sewage lifting unit WS 40-50 is available as a single-pump system (Fig. 1: WS ... E) or
as a double-pump system (Fig. 2: WS ... D), in the versions WS 40 Basic and WS 40-50. All
units are equipped with non-return valves so that it is no longer required that a non-return
valve be installed in the pressure pipe in accordance with EN 12056.
WS 40 Basic version:
• Fig. 3: PE reservoir with cover which can be walked on, in this a pump on the reservoir floor,
built-in pipework made of galvanised steel and PVC, including PVC ball valve and cast iron
non-return ball valve, as well as level-dependent control. The pump is controlled using a
float switch or level sensor, depending on the pump and type, with or without an external
switchgear (everything within the scope of delivery; see table under 5.4.1). The pressure
pipe can be disconnected from the ball valve for installing and removing the pump via the
union nut.
24
WILO SE 06/2010
English
WS 40-50 version:
• Fig. 4 and 5: PE reservoir with cover which can be walked on, surface coupling with builtin non-return ball valve made of plastic, mounted on cross member in the reservoir, discharge pipe for accommodating the suspended pump (MTS 40, TP 50 or TP 65), red brass
gate valve, pipework completely made of stainless steel, stainless steel chain for installing/
removing the pump. Switchgear and level measurement are not included in delivery with
the WS 40-50 version and must be ordered separately (see table under 5.4.2).
Types of installation
The unit can be used in two types of installations. For installation examples, see:
• Fig. 6: As sewage lifting unit inside buildings (floor-mounted installation)
• Fig. 7: As pumps station in ground installation outside of buildings (concealed floor installation)
V = backflow level (usually street level)
1. Gate valve DN 100 (accessory)
2. Flange piece DN 100 (accessory)
3. 3-way cock (accessory)
4. Diaphragm hand pump (accessory)
5. Clamp bolting (accessory)
6. Pressure pipe to the main collection pipe.
7. Wilo-Drain switchgear (see tables under 5.4.1 and 5.4.2)
8. Ventilation (connection DN 70)
9. Inlet (connection DN 100)
10. Gate valve (accessory)
11. Drainage pump (e.g. Wilo-Drain TMW)
12. Valve support for relieving weight (onsite)
13. Sump length extension (accessory)
6.2 Function
The introduced sewage is collected in the collection tank of the lifting unit. It is introduced
via a sewage inlet pipe (DN 100 or DN 150), which can be connected to any of the marked
reservoir areas (DN 100 included in delivery).
Once a certain filling level has been reached, the pump pumps the substances being conveyed via the pressure pipework into the externally connected sewage line. The built-in
non-return valve prevents backflow into the unit.
The double-pump systems work with a base-load and a peak-load pump. In order for both
pumps to be evenly loaded, there is pump cycling after every pumping operation. If a pump
malfunction occurs, the second pump automatically becomes the base-load pump.
7 Installation and electrical connection
•
•
•
•
If the product is delivered in single components, these are to be assembled in accordance
with these installation and operating instructions and all protective equipment is to be
activated. Non-observance of the information and warnings regarding mounting and
installation will impair the safety of the product/personnel and will void the given explanations regarding safety.
DANGER! Risk of fatal injury!
Inappropriate installation or improper electrical connection can be life-threatening.
The installation and electrical connection may only be carried out by qualified personnel in accordance with the applicable regulations!
Accident prevention regulations must be observed!
DANGER! Danger of suffocation!
Toxic or health-hazardous substances in sewage sumps can lead to infections or suffocation.
For safety reasons, make sure a second person is present at all times when you are
working on sumps.
Make sure the installation location is sufficiently ventilated.
7.1 Preparing for installation
CAUTION! Risk of damage!
Incorrect installation can result in property damage.
• Only use qualified personnel for installation work!
• Observe national and regional regulations!
• Observe the installation and operating instructions for the accessories!
Select a suitable place for installing the sump (Fig. 6/Fig. 7).
Installation and operating instructions Wilo-DrainLift WS 40-50
25
English
• Observe the dimensions according to the installation plan (Fig. 1/Fig. 2).
• Take into account the position of the inlet connection, pressure outlet and ventilation
connection.
• Take into account the cable length of pump and level control system so that they can be
lifted out of the sump.
• Prepare the inlet pipe, ventilation pipe and pressure outlet pipe onsite.
7.2 Setup/installation
7.2.1 Setup in buildings (floor-mounted installation)
When installing lifting units, the regionally valid regulations in particular and the corresponding specifications of EN 12056 (gravity drainage stations within buildings) in
general are to be observed!
• In accordance with EN 12056-4, installation locations for lifting units must be sufficiently
large so that the unit is freely accessible for operating and maintenance work.
• There must be sufficient working space of at least 60 cm in width/height available next to
and above all parts which are to be operated and maintained.
• The installation location must be frost-proof, ventilated and well-lit.
• The installation surface must be horizontal and flat.
• Align the reservoir with pipes prepared onsite and connect the pipes according to 7.2.
• In accordance with EN 12056-4, sewage lifting units must be installed so that they cannot
twist and turn. Units which threaten to float must be installed so that they are antibuoyant.
Fig. 8: Buoyancy safeguard
Fix the unit to the floor with the enclosed fixation material (Fig. 8).
• To do this, fasten the angle to the circumferential rib of the reservoir floor with screws.
• Drill holes in the floor.
• Properly fix the unit to the floor with dowels and screws.
7.2.2 Ground installation outside buildings (concealed floor installation)
Install and check the pumping station according to the regionally valid regulations and
relevant directives, e.g. EN 1610 (Construction and testing of drains and sewers)!
CAUTION! Risk of material damage!
Environmental influences can lead to damage to the product.
• In the case of ground installation outdoors, observe the regional depth of frost penetration. If the unit, and in particular the reservoir pressure outlet is located in the frostendangered range, shut down the unit during frost periods and drain the unit and pressure pipe.
• If the ground water is high, the unit is in danger of becoming buoyant! Observe the
maximum ground water levels! (see 5.2 Technical data)
• Dig a pit corresponding with the overall height of the unit; Observe the depth of the inlet
pipe and permissible connection area in the reservoir (Fig. 9)! If necessary, provide a sump
length extension (accessory).
• Align the reservoir with pipes prepared onsite and connect the pipes according to 7.2.
• Place the unit in a sand bed (not cohesive, grain range 0-32 mm, minimum bed thickness
200 mm), shake it in, and align it perpendicular and flush with respect to the upper edge of
the ground.
• Fill the excavation pit with layers of non-cohesive soil (sand/gravel, grain range up to
32 mm) and compact properly. Do not push the unit out of alignment or deform it.
• A leakage test is to be performed on the unit in accordance with the relevant regulations.
26
WILO SE 06/2010
English
7.3 Connecting the pipes
All pipes must be mounted without tension. No pipeline forces or torques may act on the
unit. The pipes (incl. valves) are to be fastened and supported such that neither tensile nor
compressive forces act on the unit.
The following symbols on the reservoir indicate possible pipe connections:
Symbol
Pipe connection
Symbol
Pipe connection
Inlet pipe (reservoir inlet area)
Ventilation pipe
Pressure pipe
Cable conduit
7.3.1 Inlet connection
• Install the inlet pipe so that it can drain by itself. Do not reduce the pipe diameter in the
direction of flow.
max. 620
min. 450
max. 620
min. 450
Fig. 9: Reservoir inlet area (shaded)
• Measure the position of the introduction of the inlet pipe in the reservoir. Observe the
minimum connection height for inlet in the reservoir (Fig. 9, 10)!
• Select the position so that the inlet pipe discharges perpendicularly on the reservoir surface; observe the minimum distance of 50 mm from the outer edge of the drilled hole to
the adjacent edges and finning (Fig. 10)!
• Drill a hole for the inlet with a keyhole saw (within the
scope of delivery) in one of the reservoir surfaces intended
for this purpose (Fig. 9) (observe supplementary sheet keyhole saw).
• Deburr and smooth the cut surface for a clean seal fit.
• Insert the gasket, moisten the inside area of the gasket
with lubricant and push the inlet pipe in approx. 50 mm
depth (Fig. 10).
min 150
ca. 50
min 50
Fig. 10: Drilled hole inlet
Installation and operating instructions Wilo-DrainLift WS 40-50
27
English
• In the inlet pipe in front of the reservoir, a gate valve is required when the unit is installed
within a building in accordance with EN 12056-4 (Fig. 6).
7.3.2 Pressure pipe connection
• The discharge pipeline is to be installed so that it is frost-proof.
• For units in buildings, to protect against any backflow out of the main public sewer, the
discharge pipeline is to be designed as a “pipe loop”, the bottom edge of which must lie at
the highest point above the locally defined backflow level (usually at street level) (see also
Fig. 6).
• In the case of the WS 40-50 D double-pump system, the pipeline connection must be
established onsite.
Fig. 11: Clamp bolting (discharge pipe connection for unit type WS 40 Basic)
• Connect the discharge pipeline.
• The unit type WS 40 Basic is equipped with a clamp bolting
and can also be connected using commercially available
thread fittings (Fig. 11).
• The WS 40-50 units can also be connected using commercially available thread fittings.
7.3.3 Ventilation pipe connection
Connect the ventilation pipe (pipe system Ø 75 with sealed plug-in sleeves) to the reservoir connecting piece (Ø 75) (Fig. 12).
• Saw off 30 mm from end of connecting piece.
• Remove burrs and any excess material.
• Secure the ventilation pipe against slipping out and install pipe with a downward incline
toward the unit.
Fig. 12: Ventilation, cable conduit and emergency drain connections
7.3.4 Cable conduit connection
For cables installed in a ground installation, the connecting piece (Ø 63) is to be used, or
connecting piece (Ø 75) in combination with the ventilation pipe (Fig. 12).
• Saw off 30 mm from end of connecting piece.
28
WILO SE 06/2010
English
• Remove burrs and any excess material.
• Use a commercially available pipe system with sealed plug-in sleeves as a cable conduit
and push onto the sawed-off connecting piece.
NOTE: To facilitate the laying of the connection lines (pump/level control), pull the tie into
the installed ventilation/cable conduit installed on site.
7.3.5 Emergency drain connection
It is recommended that an emergency drain be connected (diaphragm hand pump as
accessory). This connection is established at the low-lying connecting piece (Ø 50)
(Fig. 12, see also Fig. 6).
• Saw off 30 mm from end of connecting piece.
• Remove burrs and any excess material.
• Connect the pipe (Ø 50) using the included hose and hose clamps.
7.4 Installation
Remove coarse dirt from the inside of the plastic sump.
7.4.1 Pump installation
WS 40 Basic version (Fig. 3):
The pumps are already installed. Remove the transport packaging (cardboard) from the
reservoir.
WS 40-50 version (Fig. 4 and 5):
• Follow the installation and operating instructions for the pump!
• Disconnect the discharge pipe from the coupling.
• Install the pump and discharge pipe outside of the plastic sump with the enclosed screws
and gasket.
CAUTION! Danger of damage to the pump!
The pump may be damaged if it is not handled correctly. Only suspend the pump by the
handle using a chain, never suspend by the connecting/float cable!
• When using chains, these must be connected to the carrying handle using a shackle.
Only structurally approved lifting devices may be used.
• Lower the pump with discharge pipe into the unit by the chain and engage it in the coupling.
• Hang the chain on a prepared place on the reservoir wall so that it does not go into the fluid.
7.4.2 Installing the level control
Follow the installation and operating instructions for the level control!
Adjust the float switch for the single-pump units in accordance with Fig. 13. Here, the float
switch (enclosed separately for 3~ pumps) can be fastened both to the pump as well as to
the removable holding pipe using the enclosed cable ties.
C
H
L
L
A
Fig. 13: WS 40 Basic level control
L
A
C
H
[mm]
TC 40
240
350
Installation and operating instructions Wilo-DrainLift WS 40-50
70
460 min.
29
English
The level control system is to be installed onsite on the WS 40 Basic double-pump units
(WS 40D) and WS 40-50 units. For these systems, the level is controlled via a level sensor
(to be ordered separately for the WS 40-50).
Fig. 14: WS40-50 level control
The sensor is stuck in the holding pipe of the level system to
protect it (Fig. 14).
Level adjustment
CAUTION! Danger of damage to the
unit!
Improper level adjustment can lead to
operating faults or to the failure of the unit.
When adjusting the switching level, keep the
following values in mind:
• Switch-on level (ON) = Base of the inlet pipe
• Switch-off level (OFF) = Bottom edge of pump
motor
Switching volume/level adjustment
NOTE: The following table provides guide values for level adjustment/switching volumes
of the individual versions.
The switch-off level and minimum switch-on level must not be fallen short of. The switchon level can be adjusted between the minimum and maximum level, depending on the type
of unit. It should always be selected to be as great as possible, however, in order to reach a
high switching volume, but it should not lie above the base of the inlet pipe (danger of
backflow in the inlet pipe).
The specifications for the switch-on/-off level [mm] refer to the inner reservoir floor.
WS 40 Basic
WS 40 E/TC40 (1~) BV
WS 40 E/TC40 (3~) BV
WS 40 D/TC40 (1~) BV
WS 40 D/TC40 (3~) BV
Switching volume
for min. switch-on level
for max. switch-on level
Level OFF
Level ON
Level ON
[mm]
[mm]
[l]
[mm]
130
130
130
130
340
340
340
340
65
65
100
100
not adjustable
460
100
460
160
460
160
WS 40-50
WS 40 E/MTS40
WS 40 D/MTS40
WS 50 E with TP50
WS 50 E with TP65
WS 50 D with TP50
WS 50 D with TP65
[l]
Switching volume
for min. switch-on level
for max. switch-on level
Level OFF
Level ON
Level ON
[mm]
[mm]
[l]
[mm]
[l]
200
200
200
200
200
200
400
400
400
400
400
400
60
100
60
60
105
105
460
460
460
460
460
460
80
130
80
75
135
130
7.4.3 Installing pipes and connecting cable
When installing in a building, either guide the cable ends to the switchgear from the pump
connecting cable and the level sensor/float switch
• through the existing threaded cable connections on the reservoir
• or, in the case of ground installation (see 7.2.4): through the ventilation pipe/cable conduit.
• Allow an adequate cable length for the pump and level control system so that they can be
lifted out of the sump.
30
WILO SE 06/2010
English
• Tie all pipes and connecting cables together with the cable ties provided and suspend over
the upper horizontal part of the internal pipework so that they cannot enter the fluid or
the suction mouth of the pump. Do not crush or kink pipes!
7.4.4 Fitting the sump cover
WARNING! Risk of injury!
In the case of ground installation, people may fall into the open sump and seriously
injure themselves. Make sure the sump cover is on tight and secure it against being
opened without authorisation!
CAUTION! Danger of leakage!
The gasket must not slip into the threads when screwing on. When setting up inside a
building, the cover is to be tightened firmly so that the connection is pressure-tight
and no water or gas can escape.
• Before screwing on the cover, push the gasket over the outer thread up to the radius.
• As a safeguard against the cover being opened without authorisation, particularly in the
case of ground installation, this should be locked in place with the enclosed screw (Fig. 15).
• To do this, drill a hole with a Ø of 3 mm in the prefabricated recess in the outer ribbed
outlet through the cover (item 1) and reservoir flange (item 2) or extension, at approx. a
10° angle. When doing so, do not damage the cover gasket (item 3)!
• Afterwards, screw in the screw.
Fig. 15: Securing the sump cover
7.4.5 Installing optional accessories
Optional accessories are to be ordered separately. See the catalogue/price list.
Sump length extension
Observe the information sheet for the sump length extension!
CAUTION! Danger of instability!
If installing more than one extension and then also having an installation depth of more
than 1.3 m, the static safety of the unit is no longer guaranteed. The maximum permissible installation depth is 1.3 m!
If necessary, a maximum of one extension (300 mm) can be set (Fig. 7, item 13).
• Screwing in with a gasket is done the same way as with the installation of the sump cover
(see 7.3.4).
• For further installation, see the information sheet for the sump length extension.
Vacuum interrupter
Observe the information sheet for the vacuum interrupter!
The vacuum interrupter prevents the unwanted sucking empty of the unit due to underpressure in the subsequent pressure pipe.
A vacuum interrupter can be installed in WS 40-50 units (accessory) (not possible in
Basic units).
• The connection is made at the fixed part of the coupling.
• For installation, see the information sheet of the vacuum interrupter.
Installation and operating instructions Wilo-DrainLift WS 40-50
31
English
Float switch for high water alarm
To signal a water level which is too high in the reservoir (high water alarm), a float switch
(accessory) can be installed. It is installed on the holding pipe of the level system.
Fig. 16: High-water float switch (optional)
• Pull the holding pipe out of the retaining device.
• Fasten the float switch with the cable to the holding pipe
at the desired height with the enclosed cable ties.
• Insert the holding pipe again and make sure the end of the
pipe is correctly positioned in the reservoir recess (Fig. 16).
The float switch must be able to move freely!
• Pull the cable of the float switch through a free threaded
cable connection in the reservoir or run it through the cable
conduit with the other cables.
• Connect it to the switchgear or separate alarm switchgear
(accessory).
7.5 Electrical connection
DANGER! Risk of fatal injury!
Improper electrical connections can lead to fatal electrical shocks.
• Only allow electrical connections to be made by electricians licensed by the local
energy supply company and according to the valid regulations!
• Follow the installation and operating instructions for the pump, switchgear, level control device and other accessories.
• The current type and voltage of the mains connection must correspond to the details on
the pump rating plate.
• Provide a fuse on mains side as well as a residual-current-operated protection switch
according to the valid regulations.
• Check whether the cable ends of the pump connecting cable and level control device have
been installed according to 7.3.3 and connect according to the labels on the terminal strips
in the switchgear.
• Only attach the switchbox so far away from the unit so that there is enough cable length
in the reservoir available to be able to lift the pump out of the reservoir for later maintenance work.
• Earth the pumps/unit according to regulations.
• For three-phase versions, apply a clockwise rotating field.
8 Commissioning and operation
It is recommended to have commissioning carried out by the Wilo customer service.
8.1 Checking the unit
CAUTION! Risk of damage!
Dirt and solids as well as incorrect commissioning can lead to damage to the unit or
individual components during operation.
• Before commissioning, clean the entire unit to remove contaminants, particularly solids.
• Follow the installation and operating instructions for the pump, switchgear, level control device and other accessories.
Commissioning may only occur when the unit has been installed according to these installation and operating instructions and all protective measures are in place and the relevant
safety regulations, VDE regulations as well as regional regulations have been met.
Check for the presence of and proper versions of all required components and connections
(inlets, discharge pipe with check valve, ventilation via the roof, floor fixation, electrical
connection).
32
WILO SE 06/2010
English
8.2 Commissioning
Commission as follows:
• Open the reservoir cover.
• Check to make sure the pump(s) and pipes have been installed so they are (pressure) tight.
• Establish the mains connection.
• Put the pump, switchgear, level control device and other accessories into operation.
• Completely open the gate valve in the pressure pipe.
• Fill the unit via the connected inlet.
• Check the function of the unit (test run): Observe at least two switch-on/switch-off cycles
and check that the pump(s) is/are functioning properly and that the level control is set correctly. If there is backflow into the inlet pipe, which can lead to problems on the connected
objects (toilet, shower, etc.), the level control has to be corrected accordingly.
• Install the reservoir cover and check to make sure it's tight. Mount the lock screw.
The unit is ready for operation.
8.3 Decommissioning
The installation must be decommissioned before performing maintenance work or disassembly.
WARNING! Risk of burns!
Depending on the operating status of the installation, the entire pump can become very
hot. Touching the pump can cause burns.
Allow the unit and pump to cool to room temperature.
•
•
•
•
•
•
Dismantling and installation
Dismantling and installation by qualified personnel only!
Disconnect the system from the power and secure it against being switched on.
Depressurise any pressurised parts before work.
Close the gate valves (inlet and pressure pipe)!
Drain the collection reservoir (e.g. with diaphragm hand pump)!
To clean, unscrew and remove the maintenance cover.
DANGER! Risk of infection!
If the unit or unit components are to be sent in for repairs, a used unit must be drained
and cleaned before transport for hygiene reasons. Also, all parts which can be touched
must be disinfected (spray disinfection). The parts must be packed in tear-proof, sufficiently large plastic bags so that they are tightly sealed and leak-proof. They are to be
sent in without delay via instructed forwarding agents.
For longer periods of non-use, check the unit for contaminants and clean if necessary.
9 Maintenance
•
•
•
•
•
•
•
DANGER! Risk of fatal injury!
There is risk of fatal injury due to electrical shock when working on electrical equipment.
Before all maintenance and repair work, switch off the unit from the power supply and
make sure it cannot be switched on by unauthorised persons.
Work on the electrical part of the unit may only be carried out by a qualified electrician.
DANGER!
Toxic or harmful substances in sewage can lead to infections or suffocation.
Before carrying out maintenance work at the installation location, ventilate sufficiently.
Use appropriate protective equipment to prevent the risk of infection while performing
maintenance work.
For safety reasons, make sure a second person is present at all times when you are
working on sumps.
Risk of explosion when opening (avoid open sources of ignition)!
Observe the installation and operating instructions of the unit and the accessories.
Before carrying out maintenance work and repairs, observe the “Decommissioning” chapter.
The system operator must make sure that all the maintenance, inspection and installation
work is done by authorised and qualified personnel, who have acquainted themselves sufficiently with the system through a detailed study of the installation and operating instructions.
Installation and operating instructions Wilo-DrainLift WS 40-50
33
English
• Sewage lifting units are to be maintained by someone skilled to do so in accordance with
EN 12056-4. The intervals must not exceed:
• ¼ year in the case of commercial companies
• ½ year for units in multi-family houses
• 1 year for units in single-family houses.
• A maintenance report must be issued.
It is recommended to have the unit serviced and checked by the Wilo customer service.
NOTE: When drafting a maintenance plan, expensive repairs can be avoided and fault-free
operation of the unit can be achieved with a minimum of maintenance effort. Wilo customer service is available for commissioning and maintenance work.
After maintenance and repair work, install and connect the installation as described in the
chapter “Installation and electrical connection”. Switch on the machine as described in the
“Commissioning” chapter.
10 Faults, causes and remedies
Only have faults remedied by qualified personnel! Follow the safety instructions
in 9 Maintenance.
• Follow the installation and operating instructions for the pump, switchgear, level control
device and other accessories.
• If the operating fault cannot be remedied, please consult a specialist technician, Wilo
service or the closest Wilo representative.
11 Spare parts
Spare parts may be ordered via a local specialist retailer and/or Wilo customer service.
To avoid queries and incorrect orders, all data on the rating plate should be submitted for
each order.
12 Disposal
Disposing of this product properly prevents damage to the environment and risks to personal health.
1) Use public or private disposal organisations when disposing of all or part of the product.
2) For more information on proper disposal, please contact your local council or waste
disposal office or the supplier from whom you obtained the product.
Subject to change without prior notice!
34
WILO SE 06/2010
D
GB
F
EG – Konformitätserklärung
EC – Declaration of conformity
Déclaration de conformité CE
(gemäß / according / conforme 2006/42/EG, Anhang / annex / appendice II: 1A)
Hiermit erklären wir, dass die Bauart der Baureihe :
Herewith, we declare that the product type of the series:
Par le présent, nous déclarons que l’agrégat de la série :
WS40 Basic
(Die Seriennummer ist auf dem Typenschild des Produktes angegeben. /
The serial number is marked on the product site plate. /
Le numéro de série est inscrit sur la plaque signalétique du produit.)
in der gelieferten Ausführung folgenden einschlägigen Bestimmungen entspricht:
in its delivered state complies with the following relevant provisions:
est conforme aux dispositions suivantes dont il relève:
EG-Maschinenrichtlinie
EC-Machinery directive
Directives CE relatives aux machines
2006/42/EG
Die Schutzziele der Niederspannungsrichtlinie 2006/95/EG werden gemäß Anhang I, Nr. 1.5.1 der Maschinenrichtlinie 2006/42/EG eingehalten.
The protection objectives of the low-voltage directive 2006/95/EC are realized according annex I, No. 1.5.1 of the EC-Machinery directive 2006/42/EC.
o
Les objectifs protection de la directive basse-tension 2006/95/CE sont respectées conformément à appendice I, n 1.5.1 de la
directive CE relatives aux machines 2006/42/CE.
Elektromagnetische Verträglichkeit - Richtlinie
Electromagnetic compatibility - directive
Compatibilité électromagnétique- directive
2004/108/EG
Bauproduktenrichtlinie
Construction product directive
Directive de produit de construction
89/106/EWG
Angewendete harmonisierte Normen, insbesondere:
Applied harmonized standards, in particular:
Normes harmonisées, notamment:
EN 14121-1
EN 60335-2-41
EN 60034-1, EN 60204-1
EN 60730-1
EN 55014-11), EN 55014-21)
EN 61000-6-11), EN 61000-6-21)
EN 61000-6-3
EN 61000-3-21), EN 61000-3-31)
DIN EN 12050-22)
EN 12050-4
gültig für / valid for / valide pour :
1) WS 40E/TC40 (3~) BV
2) WS 40E/TC40 (1~) BV
WS 40D/TC40 (1~) BV
WS 40E/TC40 (3~) BV
WS 40D/TC40 (3~) BV
WS 40D/TC40 (1~) BV
WS 40D/TC40 (3~) BV
i.d.F/ as amended/ avec les amendements suivants :
93/68/EWG
Bei einer mit uns nicht abgestimmten technischen Änderung der oben genannten Bauarten, verliert diese Erklärung ihre Gültigkeit.
If the above mentioned series are technically modified without our approval, this declaration shall no longer be applicable.
Si les gammes mentionnées ci-dessus sont modifiées sans notre approbation, cette déclaration perdra sa validité.
Bevollmächtigter für die Zusammenstellung der technischen Unterlagen ist:
Authorized representative for the completion of the technical documentation:
Mandataire pour le complément de la documentation technique est :
Volker Netsch
Engineering Building Service
Heimgartenstraße 1-3
95030 Hof
Dortmund, 17.02.2010
Erwin Prieß
Quality Manager
Document: 2109713.1
WILO SE
Nortkirchenstraße 100
44263 Dortmund
Germany
D
GB
F
EG – Konformitätserklärung
EC – Declaration of conformity
Déclaration de conformité CE
(gemäß / according / conforme 2006/42/EG, Anhang / annex / appendice II: 1A)
Hiermit erklären wir, dass die Bauart der Baureihe :
Herewith, we declare that the product type of the series:
Par le présent, nous déclarons que l’agrégat de la série :
(Die Seriennummer ist auf dem Typenschild des Produktes angegeben. /
The serial number is marked on the product site plate. /
Le numéro de série est inscrit sur la plaque signalétique du produit.)
WS40E/MTS401)
WS40D/MTS401)
WS50E2), 3)
WS50D2), 3)
in der gelieferten Ausführung folgenden einschlägigen Bestimmungen entspricht:
in its delivered state complies with the following relevant provisions:
est conforme aux dispositions suivantes dont il relève:
EG-Maschinenrichtlinie
EC-Machinery directive
Directives CE relatives aux machines
2006/42/EG
Die Schutzziele der Niederspannungsrichtlinie 2006/95/EG werden gemäß Anhang I, Nr. 1.5.1 der Maschinenrichtlinie 2006/42/EG eingehalten.
The protection objectives of the low-voltage directive 2006/95/EC are realized according annex I, No. 1.5.1 of the EC-Machinery directive 2006/42/EC.
o
Les objectifs protection de la directive basse-tension 2006/95/CE sont respectées conformément à appendice I, n 1.5.1 de la
directive CE relatives aux machines 2006/42/CE.
Elektromagnetische Verträglichkeit - Richtlinie
Electromagnetic compatibility - directive
Compatibilité électromagnétique- directive
Bauproduktenrichtlinie
Construction product directive
Directive de produit de construction
Angewendete harmonisierte Normen, insbesondere:
Applied harmonized standards, in particular:
Normes harmonisées, notamment:
gültig für / valid for / valide pour :
2004/108/EG
89/106/EWG
i.d.F/ as amended/ avec les amendements suivants :
93/68/EWG
EN 14121-1
EN 60335-2-41
EN 60034-1, EN 60204-1
EN 60730-1
EN 55014-1, EN 55014-2
EN 61000-3-2, EN 61000-3-3
DIN EN 12050-11)
EN 12050-12)
DIN EN 12050-23)
EN 12050-4
1) WS40E/MTS40; WS40D/MTS40 komplett mit/completed with/complète avec
MTS40/21, MTS40/24 ; MTS40/27 und/and/et PL1-WS oder/or/ou PL2-WS zener barrier und/and/et Wilo-level sensor.
2) WS50E; WS50D komplett mit/completed with/complète avec
TP50F90/7,5; TP65F91/11; TP65F98/15; TP65F109/22 und/and/et PL1-WS oder/or/ou PL2-WS und/and/et Wilo-level sensor.
3) WS50E; WS50D komplett mit/completed with/complète avec
TP50F82/5,5; TP50E101/5,5; TP50E107/7,5; TP65E114/11; TP65E122/15; TP65E132/22 und/and/et PL1-WS oder/or/ou PL2-WS
und/and/et Wilo-level sensor.
Bei einer mit uns nicht abgestimmten technischen Änderung der oben genannten Bauarten, verliert diese Erklärung ihre Gültigkeit.
If the above mentioned series are technically modified without our approval, this declaration shall no longer be applicable.
Si les gammes mentionnées ci-dessus sont modifiées sans notre approbation, cette déclaration perdra sa validité.
Bevollmächtigter für die Zusammenstellung der technischen Unterlagen ist:
Authorized representative for the completion of the technical documentation:
Mandataire pour le complément de la documentation technique est :
Volker Netsch
Engineering Building Service
Heimgartenstraße 1-3
95030 Hof
Dortmund, 29.01.2010
Erwin Prieß
Quality Manager
Document: 2109706.1
WILO SE
Nortkirchenstraße 100
44263 Dortmund
Germany
NL
EG-verklaring van overeenstemming
Hiermede verklaren wij dat dit aggregaat in de geleverde uitvoering
voldoet aan de volgende bepalingen:
I
Dichiarazione di conformità CE
Con la presente si dichiara che i presenti prodotti sono conformi alle
seguenti disposizioni e direttive rilevanti:
E
Declaración de conformidad CE
Por la presente declaramos la conformidad del producto en su estado de
suministro con las disposiciones pertinentes siguientes:
EG-richtlijnen betreffende machines 2006/42/EG
De veiligheidsdoelstellingen van de laagspanningsrichtlijn worden
overeenkomstig bijlage I, nr. 1.5.1 van de machinerichtlijn 2006/42/EG
aangehouden.
Elektromagnetische compatibiliteit 2004/108/EG
Bouwproductenrichtlijn 89/106/EEG als vervolg op 93/86/EEG
Direttiva macchine 2006/42/EG
Gli obiettivi di protezione della direttiva macchine vengono rispettati
secondo allegato I, n. 1.5.1 dalla direttiva macchine 2006/42/CE.
gebruikte geharmoniseerde normen, in het bijzonder:
zie vorige pagina
Compatibilità elettromagnetica 2004/108/EG
Direttiva linee guida costruzione dei prodotti 89/106/CEE e seguenti
modifiche 93/68/CEE
norme armonizzate applicate, in particolare:
vedi pagina precedente
Directiva sobre máquinas 2006/42/EG
Se cumplen los objetivos en materia de seguridad establecidos en la
Directiva de Baja tensión según lo especificado en el
Anexo I, punto 1.5.1 de la Directiva de Máquinas 2006/42/CE.
Directiva sobre compatibilidad electromagnética 2004/108/EG
Directiva sobre productos de construcción 89/106/CEE modificada por
93/68/CEE
normas armonizadas adoptadas, especialmente:
véase página anterior
P
Declaração de Conformidade CE
Pela presente, declaramos que esta unidade no seu estado original, está
conforme os seguintes requisitos:
S
CE- försäkran
Härmed förklarar vi att denna maskin i levererat utförande motsvarar
följande tillämpliga bestämmelser:
N
EU-Overensstemmelseserklæring
Vi erklærer hermed at denne enheten i utførelse som levert er i
overensstemmelse med følgende relevante bestemmelser:
Directivas CEE relativas a máquinas 2006/42/EG
Os objectivos de protecção da directiva de baixa tensão são cumpridos de
acordo com o anexo I, nº 1.5.1 da directiva de máquinas 2006/42/CE.
Compatibilidade electromagnética 2004/108/EG
Directiva sobre produtos de construção 89/106/CEE com os
aditamentos seguintes 93/68/EWG
normas harmonizadas aplicadas, especialmente:
ver página anterior
EG–Maskindirektiv 2006/42/EG
Produkten uppfyller säkerhetsmålen i lågspänningsdirektivet enligt bilaga
I, nr 1.5.1 i maskindirektiv 2006/42/EG.
EG–Elektromagnetisk kompatibilitet – riktlinje 2004/108/EG
EG-Byggmaterialdirektiv 89/106/EWG med följande ändringar
93/68/EWG
tillämpade harmoniserade normer, i synnerhet:
se föregående sida
EG–Maskindirektiv 2006/42/EG
Lavspenningsdirektivets vernemål overholdes i samsvar med
vedlegg I, nr. 1.5.1 i maskindirektivet 2006/42/EF.
EG–EMV–Elektromagnetisk kompatibilitet 2004/108/EG
Byggevaredirektiv 89/106/EWG med senere tilføyelser 93/68/EWG
FIN
CE-standardinmukaisuusseloste
Ilmoitamme täten, että tämä laite vastaa seuraavia asiaankuuluvia
määräyksiä:
DK
EF-overensstemmelseserklæring
Vi erklærer hermed, at denne enhed ved levering overholder følgende
relevante bestemmelser:
H
EK-megfelelségi nyilatkozat
Ezennel kijelentjük, hogy az berendezés megfelel az alábbi irányelveknek:
EU–konedirektiivit: 2006/42/EG
Pienjännitedirektiivin suojatavoitteita noudatetaan
konedirektiivin 2006/42/EY liitteen I, nro 1.5.1 mukaisesti.
EU–maskindirektiver 2006/42/EG
Lavspændingsdirektivets mål om beskyttelse overholdes i henhold til bilag
I, nr. 1.5.1 i maskindirektivet 2006/42/EF.
Sähkömagneettinen soveltuvuus 2004/108/EG
EU materiaalidirektiivi 89/106/EWG seuraavin täsmennyksin 93/68/EWG
Elektromagnetisk kompatibilitet: 2004/108/EG
Produktkonstruktionsdirektiv 98/106/EWG følgende 93/68/EWG
käytetyt yhteensovitetut standardit, erityisesti:
katso edellinen sivu.
anvendte harmoniserede standarder, særligt:
se forrige side
Gépek irányelv: 2006/42/EK
A kisfeszültség irányelv védelmi elírásait a
2006/42/EK gépekre vonatkozó irányelv I. függelékének 1.5.1. sz. pontja
szerint teljesíti.
Elektromágneses összeférhetség irányelv: 2004/108/EK
Építési termékek irányelv 89/106/EGK és az azt kiváltó 93/68/EGK
irányelv
alkalmazott harmonizált szabványoknak, különösen:
lásd az elz oldalt
CZ
Prohlášení o shod ES
Prohlašujeme tímto, že tento agregát vdodaném provedení odpovídá
následujícím píslušným ustanovením:
Smrnice ES pro strojní zaízení 2006/42/ES
Cíle týkající se bezpe&nosti stanovené ve sm'rnici o elektrických
zaízeních nízkého nap'tí jsou dodrženy podle pílohy I, &. 1.5.1 sm'rnice
o strojních zaízeních 2006/42/ES.
Smrnice o elektromagnetické kompatibilit 2004/108/ES
Smrnice pro stavební výrobky 89/106/EHS ve zn'ní 93/68/EHS
PL
Deklaracja Zgodnoci WE
Niniejszym deklarujemy z pen odpowiedzialnoci, e dostarczony
wyrób jest zgodny z nast
pujcymi dokumentami:
dyrektyw maszynow WE 2006/42/WE
Przestrzegane s cele ochrony dyrektywy niskonapi
ciowej zgodnie z
zacznikiem I, nr 1.5.1 dyrektywy maszynowej 2006/42/WE.
anvendte harmoniserte standarder, særlig:
se forrige side
použité harmoniza&ní normy, zejména:
viz pedchozí strana
dyrektyw dot. kompatybilnoci elektromagnetycznej 2004/108/WE
dyrektyw w sprawie wyrobów budowlanych 89/106/EWG w brzmieniu
93/68/EWG
stosowanymi normami zharmonizowanymi, a w szczególnoci:
patrz poprzednia strona
RUS
, ! "#
$ % ! :
EC 2006/42/EG
*!" $ "$, + ! $
< $!+%, "%% $!+% I,
= 1.5.1 ! > > 2006/42/?G.
2004/108/EG
! "#! 89/106/EWG $$!
93/68/EWG
@$< ! !, :
. $!% !J
GR
$%&'() (*++;<='()> ?)> @@
RX[\]^_`{ |} }^ €^‚|] ƒ_}| „’ ƒ_}… }X] †ƒ}‡„}ƒ„X €ƒ‡ˆ^„X‰
†ƒ]^€^{Š }‰ ƒ†|[^_‹{‰ ˆƒ}‡Œ{‰ :
TR
CE Uygunluk Teyid Belgesi
Bu cihazn teslim edildiŽi ekliyle aaŽdaki standartlara uygun olduŽunu
teyid ederiz:
RO
EC-DeclaraAie de conformitate
Prin prezenta declar‘m c‘ acest produs aa cum este livrat, corespunde cu
urm‘toarele prevederi aplicabile:
JQ)XY[> E\ X]^ +)_^`%+^?^ 2006/42/E\
’ ƒ€ƒ}…„{‰ €^„}ƒ„Šƒ‰ }X‰ ^ˆX“Šƒ‰ ”ƒ`X[…‰ }‡„X‰ }X^•]}ƒ
„•`–—]ƒ `{ }^ €ƒ‡}X`ƒ I, ƒ. 1.5.1 }X‰ ^ˆX“Šƒ‰ „”{}†‡ `{ }ƒ
`X”ƒ]…`ƒ}ƒ 2006/42/EG.
~&[?<€+^X`)?]% (*+^?;?)?^ E\-2004/108/E\
JQ)XY^ ^?^([*%> 89/106/EJ\ |€—‰ }^€^€^…‹X†{ 93/68/E’š
AB-Makina Standartlar| 2006/42/EG
Alçak gerilim yönergesinin koruma hedefleri, 2006/42/AT makine
yönergesi Ek I, no. 1.5.1'e uygundur.
Elektromanyetik Uyumluluk 2004/108/EG
Ürün imalat yönetmeliƒi 89/106/EWG ve takip eden, 93/68/EWG
›]ƒ`^]„`œ]ƒ ”X„`^€^^•`{]ƒ €|}_€ƒ, ˆƒŠ}{ƒ:
Ÿ[œ€{ €^X“^•`{]X „{[Šˆƒ
ksmen kullanlan standartlar için:
bkz. bir önceki sayfa
Directiva CE pentru ma}ini 2006/42/EG
Sunt respectate obiectivele de protec™ie din directiva privind joasa
tensiune conform Anexei I, Nr. 1.5.1 din directiva privind mainile
2006/42/CE.
Compatibilitatea electromagnetic‚ – directiva 2004/108/EG
Directiva privind produsele pentru construcAii 89/106/EWG cu
amendamentele ulterioare 93/68/EWG
standarde armonizate aplicate, îndeosebi:
vezi pagina precedent‘
EST
EÜ vastavusdeklaratsioon
Käesolevaga tõendame, et see toode vastab järgmistele asjakohastele
direktiividele:
LV
EC - atbilst„bas deklar†cija
Ar šo m s apliecin¡m, ka šis izstr¡d¡jums atbilst sekojošiem noteikumiem:
LT
EB atitikties deklaracija
Šiuo pažymima, kad šis gaminys atitinka šias normas ir direktyvas:
Masinadirektiiv 2006/42/EÜ
Madalpingedirektiivi kaitse-eesmärgid on täidetud vastavalt masinate
direktiivi 2006/42/EÜ I lisa punktile 1.5.1.
Maš„nu direkt„va 2006/42/EK
Zemsprieguma direkt£vas droš£bas m r¤i tiek iev roti atbilstoši Maš£nu
direkt£vas 2006/42/EK pielikumam I, Nr. 1.5.1.
Mašin‡ direktyv 2006/42/EB
Laikomasi Žemos ¦tampos direktyvos keliam§ saugos reikalavim§ pagal
Mašin§ direktyvos 2006/42/EB I priedo 1.5.1 punkt.
Elektromagnetilise ühilduvuse direktiiv 2004/108/EÜ
Ehitustoodete direktiiv 89/106/EÜ, muudetud direktiiviga 93/68/EMÜ
kohaldatud harmoneeritud standardid, eriti:
vt eelmist lk
Elektromagnˆtisk†s savietojam„bas direkt„va 2004/108/EK
Direkt„va par b‰vizstr†d†jumiem 89/106/EK p c labojumiem 93/68/EES
piem roti harmoniz ti standarti, tai skait¡:
skat£t iepriekš jo lappusi
Elektromagnetinio suderinamumo direktyv 2004/108/EB
Statybos produkt‡ direktyvos 89/106/EB patais 93/68/EEB
pritaikytus vieningus standartus, o b¨tent:
žr. ankstesniame puslapyje
SK
ES vyhlásenie o zhode
Týmto vyhlasujeme, že konštrukcie tejto konštruk&nej série v dodanom
vyhotovení vyhovujú nasledujúcim príslušným ustanoveniam:
Stroje - smernica 2006/42/ES
Bezpe&nostné ciele smernice o nízkom napätí sú dodržiavané v zmysle
prílohy I, &. 1.5.1 smernice o strojových zariadeniach 2006/42/ES.
SLO
ES – izjava o skladnosti
Izjavljamo, da dobavljene vrste izvedbe te serije ustrezajo slede&im
zadevnim dolo&ilom:
Direktiva o strojih 2006/42/ES
Cilji Direktive o nizkonapetostni opremi so v skladu s
prilogo I, št. 1.5.1 Direktive o strojih 2006/42/EG doseženi.
BG
EŠ-
" ‹
©!!, $!# ! :
Elektromagnetická zhoda - smernica 2004/108/ES
Stavebné materiály - smernica 89/106/ES pozmenená 93/68/EHP
Direktiva o elektromagnetni združljivosti 2004/108/ES
Direktiva o gradbenih proizvodih 89/106/EGS v verziji 93/68/EGS
používané harmonizované normy, najmä:
pozri predchádzajúcu stranu
uporabljeni harmonizirani standardi, predvsem:
glejte prejšnjo stran
Π#
2006/42/EO
ª !$!" $!+ # #. «!+ I, = 1.5.1 ©! > 2006/42/E¬.
E
‹ – #
2004/108/EŠ
" 89/106/Š 93/68/?@­
®!! !:
+. $! !J
M
Dikjarazzjoni ta’ konformità KE
B'dan il-mezz, niddikjaraw li l-prodotti tas-serje jissodisfaw iddispoizzjonijiet relevanti li ¯ejjin:
Makkinarju - Direttiva 2006/42/KE
L-objettivi tas-sigurta tad-Direttiva dwar il-Vulta¯¯ Baxx huma konformi
mal-Anness I, Nru 1.5.1 tad-Direttiva dwar il-Makkinarju 2006/42/KE.
Kompatibbiltà elettromanjetika - Direttiva 2004/108/KE
Direttiva dwar il-prodotti tal-kostruzzjoni 89/106/KEE kif emendata bidDirettiva 93/68/KEE
kif ukoll standards armonizzati b'mod partikolari:
ara l-pa¯na ta' qabel
WILO SE
Nortkirchenstraße 100
44263 Dortmund
Germany
WILO SE
Nortkirchenstraße 100
44263 Dortmund
Germany
T 0231 4102-0
F 0231 4102-7363
[email protected]
www.wilo.de
Wilo – International (Subsidiaries)
Argentina
WILO SALMSON
Argentina S.A.
C1295ABI Ciudad
Autónoma de Buenos Aires
T+ 54 11 4361 5929
[email protected]
Austria
WILO Pumpen
Österreich GmbH
1230 Wien
T +43 507 507-0
[email protected]
Azerbaijan
WILO Caspian LLC
1065 Baku
T +994 12 5962372
[email protected]
Belarus
WILO Bel OOO
220035 Minsk
T +375 17 2503393
[email protected]
Belgium
WILO SA/NV
1083 Ganshoren
T +32 2 4823333
[email protected]
Bulgaria
WILO Bulgaria Ltd.
1125 Sofia
T +359 2 9701970
[email protected]
Croatia
WILO Hrvatska d.o.o.
10090 Zagreb
T +38 51 3430914
[email protected]
Czech Republic
WILO Praha s.r.o.
25101 Cestlice
T +420 234 098711
[email protected]
Denmark
WILO Danmark A/S
2690 Karlslunde
T +45 70 253312
[email protected]
Estonia
WILO Eesti OÜ
12618 Tallinn
T +372 6509780
[email protected]
Finland
WILO Finland OY
02330 Espoo
T +358 207401540
[email protected]
France
WILO S.A.S.
78390 Bois d'Arcy
T +33 1 30050930
[email protected]
Canada
WILO Canada Inc.
Calgary, Alberta T2A 5L4
T +1 403 2769456
[email protected]
Great Britain
WILO (U.K.) Ltd.
DE14 2WJ BurtonUpon-Trent
T +44 1283 523000
[email protected]
China
WILO China Ltd.
101300 Beijing
T +86 10 58041888
[email protected]
Greece
WILO Hellas AG
14569 Anixi (Attika)
T +302 10 6248300
[email protected]
Hungary
WILO Magyarország Kft
2045 Törökbálint
(Budapest)
T +36 23 889500
[email protected]
India
WILO India Mather and
Platt Pumps Ltd.
Pune 411019
T +91 20 27442100
service@
pun.matherplatt.co.in
Indonesia
WILO Pumps Indonesia
Jakarta Selatan 12140
T +62 21 7247676
[email protected]
Ireland
WILO Engineering Ltd.
Limerick
T +353 61 227566
[email protected]
Italy
WILO Italia s.r.l.
20068 Peschiera
Borromeo (Milano)
T +39 25538351
[email protected]
Latvia
WILO Baltic SIA
1019 Riga
T +371 67 145229
[email protected]
Russia
WILO Rus ooo
123592 Moscow
T +7 495 7810690
[email protected]
Switzerland
EMB Pumpen AG
4310 Rheinfelden
T +41 61 83680-20
[email protected]
Lebanon
WILO SALMSON
Lebanon
12022030 El Metn
T +961 4 722280
[email protected]
Saudi Arabia
WILO ME - Riyadh
Riyadh 11465
T +966 1 4624430
[email protected]
Taiwan
WILO-EMU Taiwan Co. Ltd.
110 Taipeh
T +886 227 391655
nelson.wu@
wiloemutaiwan.com.tw
Lithuania
WILO Lietuva UAB
03202 Vilnius
T +370 5 2136495
[email protected]
The Netherlands
WILO Nederland b.v.
1551 NA Westzaan
T +31 88 9456 000
[email protected]
Serbia and Montenegro
WILO Beograd d.o.o.
11000 Beograd
T +381 11 2851278
[email protected]
Slovakia
WILO Slovakia s.r.o.
82008 Bratislava 28
T +421 2 45520122
[email protected]
Norway
WILO Norge AS
0975 Oslo
T +47 22 804570
[email protected]
Slovenia
WILO Adriatic d.o.o.
1000 Ljubljana
T +386 1 5838130
[email protected]
Poland
WILO Polska Sp. z.o.o.
05-090 Raszyn
T +48 22 7026161
[email protected]
South Africa
Salmson South Africa
1610 Edenvale
T +27 11 6082780
errol.cornelius@
salmson.co.za
Kazakhstan
WILO Central Asia
050002 Almaty
T +7 727 2785961
[email protected]
Portugal
Bombas Wilo-Salmson
Portugal Lda.
4050-040 Porto
T +351 22 2080350
[email protected]
Korea
WILO Pumps Ltd.
621-807 Gimhae
Gyeongnam
T +82 55 3405890
[email protected]
Romania
WILO Romania s.r.l.
077040 Com. Chiajna
Jud. Ilfov
T +40 21 3170164
[email protected]
Turkey
WILO Pompa Sistemleri
San. ve Tic. A.Ş.
34530 Istanbul
T +90 216 6610211
[email protected]
Ukraina
WILO Ukraina t.o.w.
01033 Kiew
T +38 044 2011870
[email protected]
United Arab Emirates
WILO Middle East FZE
Jebel Ali - Dubai
T +971 4 886 4771
[email protected]
USA
WILO-EMU USA LLC
Thomasville,
Georgia 31792
T +1 229 5840097
[email protected]
Spain
WILO Ibérica S.A.
28806 Alcalá de Henares
(Madrid)
T +34 91 8797100
[email protected]
WILO USA LLC
Melrose Park, Illinois 60160
T +1 708 3389456
mike.easterley@
wilo-na.com
Sweden
WILO Sverige AB
35246 Växjö
T +46 470 727600
[email protected]
Vietnam
WILO Vietnam Co Ltd.
Ho Chi Minh City, Vietnam
T +84 8 38109975
[email protected]
Wilo – International (Representation offices)
Algeria
Bad Ezzouar, Dar El Beida
T +213 21 247979
[email protected]
Bosnia and Herzegovina
71000 Sarajevo
T +387 33 714510
[email protected]
Macedonia
1000 Skopje
T +389 2 3122058
[email protected]
Moldova
2012 Chisinau
T +373 2 223501
[email protected]
Tajikistan
734025 Dushanbe
T +992 37 2232908
farhod.rahimov@ wilo.tj
Uzbekistan
100015 Tashkent
T +998 71 1206774
[email protected]
Armenia
375001 Yerevan
T +374 10 544336
[email protected]
Georgia
0179 Tbilisi
T +995 32 306375
[email protected]
Mexico
07300 Mexico
T +52 55 55863209
roberto.valenzuela@ wilo.com.mx
Rep. Mongolia
Ulaanbaatar
T +976 11 314843
[email protected]
Turkmenistan
744000 Ashgabad
T +993 12 345838
[email protected]
November 2009
WILO SE
Nortkirchenstraße 100
44263 Dortmund
Germany
T 0231 4102-0
F 0231 4102-7363
[email protected]
www.wilo.de
Wilo-Vertriebsbüros in Deutschland
G1 Nord
WILO SE
Vertriebsbüro Hamburg
Beim Strohhause 27
20097 Hamburg
T 040 5559490
F 040 55594949
[email protected]
G3 Ost
WILO SE
Vertriebsbüro Dresden
Frankenring 8
01723 Kesselsdorf
T 035204 7050
F 035204 70570
[email protected]
G5 Süd-West
WILO SE
Vertriebsbüro Stuttgart
Hertichstraße 10
71229 Leonberg
T 07152 94710
F 07152 947141
[email protected]
G2 Nord-Ost
WILO SE
Vertriebsbüro Berlin
Juliusstraße 52–53
12051 Berlin-Neukölln
T 030 6289370
F 030 62893770
[email protected]
G4 Süd-Ost
WILO SE
Vertriebsbüro München
Adams-Lehmann-Straße 44
80797 München
T 089 4200090
F 089 42000944
[email protected]
G6 Mitte
WILO SE
Vertriebsbüro Frankfurt
An den drei Hasen 31
61440 Oberursel/Ts.
T 06171 70460
F 06171 704665
[email protected]
Kompetenz-Team
Gebäudetechnik
WILO SE
Nortkirchenstraße 100
44263 Dortmund
T 0231 4102-7516
T 01805 R•U•F•W•I•L•O*
7•8•3•9•4•5•6
F 0231 4102-7666
Kompetenz-Team
Kommune
Bau + Bergbau
WILO EMU GmbH
Heimgartenstraße 1
95030 Hof
T 09281 974-550
F 09281 974-551
Erreichbar Mo–Fr von 7–18 Uhr.
–Antworten auf
– Produkt- und Anwendungsfragen
– Liefertermine und Lieferzeiten
–Informationen über Ansprechpartner vor Ort
–Versand von Informationsunterlagen
* 0,14 €/Min. aus dem Festnetz,
Mobilfunk max. 0,42 €/Min.
Werkskundendienst
Gebäudetechnik
Kommune
Bau + Bergbau
Industrie
WILO SE
Nortkirchenstraße 100
44263 Dortmund
T 0231 4102-7900
T 01805 W•I•L•O•K•D*
9•4•5•6•5•3
F 0231 4102-7126
[email protected]
Erreichbar Mo–So von
7–18 Uhr.
In Notfällen täglich
auch von
18–7 Uhr.
–Kundendienst-Anforderung
–Werksreparaturen
–Ersatzteilfragen
–Inbetriebnahme
–Inspektion
–Technische Service-Beratung
–Qualitätsanalyse
Wilo-International
Österreich
Zentrale Wien:
WILO Pumpen Österreich GmbH
Eitnergasse 13
1230 Wien
T +43 507 507-0
F +43 507 507-15
Vertriebsbüro Salzburg:
Gnigler Straße 56
5020 Salzburg
T +43 507 507-13
F +43 507 507-15
Vertriebsbüro Oberösterreich:
Trattnachtalstraße 7
4710 Grieskirchen
T +43 507 507-26
F +43 507 507-15
Schweiz
EMB Pumpen AG
Gerstenweg 7
4310 Rheinfelden
T +41 61 83680-20
F +41 61 83680-21
G7 West
WILO SE
Vertriebsbüro Düsseldorf
Westring 19
40721 Hilden
T 02103 90920
F 02103 909215
[email protected]
Standorte weiterer
Tochtergesellschaften
Argentinien, Aserbaidschan,
Belarus, Belgien, Bulgarien,
China, Dänemark, Estland,
Finnland, Frankreich,
Griechenland, Großbritannien,
Indien, Indonesien, Irland,
Italien, Kanada, Kasachstan,
Korea, Kroatien, Lettland,
Libanon, Litauen,
Niederlande, Norwegen,
Polen, Portugal, Rumänien,
Russland, Saudi-Arabien,
Schweden, Serbien und
Montenegro, Slowakei,
Slowenien, Spanien,
Südafrika, Taiwan,
Tschechien, Türkei, Ukraine,
Ungarn, USA, Vereinigte
Arabische Emirate, Vietnam
Die Adressen finden Sie unter
www.wilo.com.
Stand Januar 2010
">