MCV4 is a MIDI-to-CV/GATE

MCV4 is a MIDI-to-CV/GATE
DOEPFER
MIDI TO CV/GATE INTERFACE
MCV4
Bedienungsanleitung (deutsch)
User's Guide (English)
www.doepfer.de
www.doepfer.com
INTRODUCTION
MCV4 is a MIDI-to-CV/GATE-Interface to control vintage analog synthesizers equipped with
CV and Gate/Trigger inputs via MIDI. MCV4 is suitable for synthesizers using voltage control
characteristics of 1V/Octave and gate voltages from +5V to +12V or switched trigger (S-Trig).
MCV4 is eqipped with a standard control voltage output (CV1) to control the VCO's (Voltage
Controlled Oscillator) and a Gate/Trigger output to control the Envelope Generators (e.g. of
ADSR type). On top of it MCV4 is equipped with additional 3 control voltage outputs
(CV2...4) to control other parameters of the synthesizer connected to MCV4 (like VCF
frequency, loudness, modulation depth and so on) provided that it the regarding control
voltage inputs are available. The 3 additional CV's are controlled with the MIDI events AfterTouch, Volume (Ctr. #7) and a free adjustable MIDI controller. In addition the MIDI velocity
can be used as a factor to multiply the values of the CV's controlled by Volume and the
selectable controller. The MIDI channel, the reference note for 0V CV1 and the MIDI
controller for CV4 can be adjusted.
If you want to control more than one synthesizer or syntesizer module or if you need more
control voltages we recommend the MCV24. The MCV24 is equipped with 24 CV/Gate
outputs and additional SYNC/Clock/Start/Stop outputs. The MCV24 will be probably
available end of 97.
CONNECTIONS
The MCV4 does not have a built-in power supply. Instead it uses a plug-in type EXTERNAL
POWER SUPPLY (AC adapter). The power supply is NOT included with the MCV4 and must
be purchased locally by the user.
We recommend a VDE approved AC adapter but MCV4 will work with every AC adapter
beeing in accordance with the following specifications. The adapter must be able to deliver 712 V DC unstabilized or stabilized voltage, as well as a minimum current of 100 mA. The
POLARITY of the low voltage plug connected to the MCV4 must be pin = +7...12V and ring =
GND. If the polarity is incorrect, MCV4 will not function. However, there is no danger of
damage to the circuitry since it is protected by a diode. If the MCV4 is used in Germany the
external power supply must be VDE approved due to security and product liability reasons.
The MCV4 is turned on by plugging the AC adapter into a wall outlet and connecting it to the
appropriate jack "9V DC" on the MCV4. There is no separate ON/OFF switch.
Connect MIDI IN of the MCV4 to MIDI OUT of the MIDI transmitter (MIDI sequencer,
synthesizer, masterkeyboard,....). The MIDI THRU of the MCV4 may be connected to the
MIDI IN of other MIDI devices (optional). If this is not required the MIDI THRU connector
remains not connected.
The GATE output of the MCV4 is a monophonic 1/4" jack socket. The Gate/Trigger signal
appears at the top of a jack plug connected to the Gate output of the MCV4. If your
synthesizers uses a 1/4" jack socket for Gate/Trigger input a monophonic 1/4" cable can be
used for the Gate connection between MCV4 and your synthesizer.
The CV outputs of the MCV4 are stereophonic 1/4" jack socket. The CV's of each jack are
available at the tip and the ring. At the socket located near the Gate output the control
voltages CV1 (MIDI note controlled) and CV2 (MIDI after touch controlled) are available. At
the other CV socket CV3 (MIDI volume controlled) and CV4 (controlled by an adjustable
MIDI controller) are available. The sketches at the top of the MCV4 housing show the
connections.
If you want to use both CV's of one connector you probably need a special cable with one
1/4" stereo jack plug on one side (MCV4) and two 1/4" mono jack plugs on the other
(synthesizer). We offer such a special cable for the MCV4 and you should order it together
with the MCV4 because of the additional shipment and money transfer costs. But you may
MCV4 User's Guide - Page 1
get such a cable from your local dealer as well. Of course you may use special adapters
(1/4" stereo to 2x1/4" mono) too.
The CV1 output of the MCV4 is connected to the control voltage input of the synthesizer
which controls the pitch (labeled e.g. as CV, tune, pitch, VCO, Osc. or similiar). Pay attention
that the MCV4 can be used only for synthesizers using the 1V/Oct. characteristic for CV and
not for those using Hz/V. Most of the vintage synthesizers use 1V/Oct (e.g. Moog, Roland,
Sequential Circuits, Doepfer) but some manufacturers used Hz/V (e.g. Yamaha, Korg) or
completely other control characteristics (e.g. EMS Synthi A: 0.32V/Oct or 0.26V/Oct). But for
some synthesizers with V/Oct. there is a solution to control it via V/Oct. (e.g. the Korg
MS10/MS20, see below).
The GATE output of the MCV4 is connected to Gate or trigger input of the synthesizer
(labeled e.g. Gate, Trigger, Trig., S-Trig. or similiar). Please check which type of Gate/Trigger
is used with your synthesizer: Voltage Trigger or S-Trigger/Switched Trigger.
Please refer to the manual of your synthesizer which types of CV control characteristics and
Gate/Trigger are used and how the connectors are wired.
E.g. the Mini Moog uses a very unique connector for the S-Trigger input. You will have
problems to find this type of connector today. You could solve the problem by replacing the
unique connector by a 1/4" jack socket.
E.g. if you want to control a MOOG Rogue or MOOG Source with the MCV4 pay attention to
the unusual assignement of the Moog jack sockets! You have to use stereo jack plugs on the
Moog side in this special case (Rogue/Source CV socket: ring = CV Input / Rogue/Source
GATE socket: ring = voltage trigger input or tip = s-trigger input). You may find details in the
user's guide of your synthesizer.
E.g. many Roland synthesizers use 3.5mm miniature jack sockets. Here you need special
cables or adapters with 1/4" jack plugs on one side (MCV4 side) and 3.5mm jack plugs on
the other (synthesizer side).
The Korg Synthesizers MS10 and MS20 e.g. are equipped with an external control input
labeled "TOTAL" that can be adjusted to 1V/Octave with the control knob labeled
"MG/T.EXT.". Using this input the MS10/MS20 can be controlled with 1V/Oct. control
voltages.
The factory adjustment of the CV1 output is 1.00V/Octave. The voltage range of the CV1
output is 0...+5V, i.e. 5 octaves.To change or re-adjust the scale you have to open the MCV4
case and adjust the scale with the trimming potentiometer located behind the power supply
connector to the desired value. Incoming MIDI pitch bend events affect the CV1 voltage. The
maximum pitch bend voltage travel is +/-1 V corresponding to +/-1 octave. You have to pay a
little attention when using the pitch bend function. If you play a note on your keyboard which
corresponds to a CV voltage below +1 V or above +4 V not the entire pitch travel is available
as the possible output voltage ranges only from 0 to +5V. If you want to use the pitch bend
function you should play in the mid range to have enough voltage travel for the pitch bend
function.
The CV2 output is controlled via (monophonic) After Touch messages on the MIDI channel
of the MCV4. The voltage range is about 0...+5V.
The CV3 output is controlled via Volume messages (= Ctrl. #7) on the MIDI channel of the
MCV4. The voltage range is about 0...+5V. It is possible to tie up the CV3 additionally with
velocity (see chapter Operation for details).
The CV4 output is controlled via any MIDI controller on the MIDI channel of the MCV4. The
voltage range is about 0...+5V. It is possible to tie up the CV4 additionally with velocity (see
chapter Operation for details).
MCV4 User's Guide - Page 2
The factory setting for the GATE output is +5V voltage gate. If you want to change the
setting you have to open the MCV4 case. Before opening the case disconnect the MCV4
from the AC adapter and remove all connections. Open the case of the MCV4 by removing
the 4 screws using a suitable tool. Inside you see the pc board with a jumper located near
the Gate jack socket. The jumper can be set in one of 3 different ways:
• +5V Voltage Gate: jumper set away from the pc board edge (factory setting)
• +U Voltage Gate: jumper set to the pc board edge
• S-Trigger:
jumper removed (e.g. for most of the Moog synthesizers)
To select S-trigger you have to remove the jumper. +U means that the gate voltage is equal
to the output voltage of the AC adapter used. As the admitted voltage range of the AC
adapter is +7...+12V the gate voltage has the same range when the jumper is set to +U. E.g.
if your synthesizer requires a gate voltage of +10 V or more you should use the +U setting of
the jumper and an AC adapter with about 12V output voltage.
Which type of CV characteristics and Gate is required for your synthesizer you may find in
the manual of your synthesizer.
Pay attention if you open and close the MCV4 case (e.g. for adjusting the scale or
changing the Gate/Trigger setting). Use only a suitable screw driver and open/close the
case very carefully.. We cannot take back units if the case or LEDs or the switch are
damaged and the warranty will be lost during such manipulations. If you are not sure
whether your are able to do the modification send the unit to your local dealer or to
Doepfer Musikelektronik, Graefelfing (Germany).
OPERATION
When using an external power supply the MCV4 is SWITCHED ON
The MCV4 is SWITCHED ON by plugging the AC adapter into a wall outlet and connecting it
to the power supply jack labeled "9V DC" of the MCV4. There is no separate ON/OFF switch.
After power on the LED on the MCV4 will light up for a short time. Otherwise the AC adapter
used is not suitable or does not work.
The external power supply (AC adapter) is NOT included with the MCV4 and must be
purchased locally by the user. We recommend an VDE approved AC adapter but MCV4 will
work with every AC adapter being in accordance with the following specifications. The
adapter must be able to deliver 7-12 V DC unstabilized or stabilized voltage, as well as a
minimum current of 100 mA. The POLARITY of the low voltage plug connected to the MCV4
must be pin = +7...12V and ring = GND (see sketch on the MCV4 housing). If the polarity is
incorrect, MCV4 will not function. However, there is no danger of damage to the circuitry
since it is protected by a diode. If the MCV4 is used in Germany the external power supply
must be VDE approved.
In the normal mode (i.e. not in the learn mode) the LED displays the state of the Gate output.
You may use the LED to control the correct MCV4 function without having a synthesizer
connected to the MCV4.
When turning on the MCV4 the last configuration before the unit was turned off is called up,
i.e. the parameters for MIDI channel, reference note, gate polarity, retrigger and so on.
To adjust the MCV4 parameters (like MIDI channel or gate polarity) you have to enter the
MCV4 learn mode and send the regarding MIDI messages to the MCV4 from your MIDI
controlling while the MCV4 is in learn mode. To enter the learn mode one has to press the
learn button and hold it pressed down for about one second. The one-second-delay was
programmed to prevent the unintentional release of the learn mode. Whenever the LED is
flashing without incoming MIDI messages the learn mode is active. In this mode the MCV4 is
looking forward to an incoming MIDI note on, program change or controller event (see table
MCV4 User's Guide - Page 3
below). If you have entered the learn mode by mistake you can leave it by pressing the learn
button again. The learn mode will also be terminated if one of the MIDI events in the table
below is received.
While the MCV4 is in learn mode the following parameters can be adjusted via incoming
MIDI messages:
Function
MIDI channel/reference for CV1=0V
CV3 velocity off
CV3 velocity on
CV4 velocity off
CV4 velocity on
Retrigger: off
Retrigger: on
Trigger polarity: normal
Trigger polarity: invertet
CV3 velocity mode 127 steps
CV3 velocity mode 2 steps
CV4 velocity mode 127 steps
CV4 velocity mode 2 steps
Key assign mode: highest note
Key assign mode: last note
Key assign mode: reference note
Key assign mode: stack note
Characteristics: V/Octave
Characteristics: Hz/V
Controller for CV4
MIDI message
Note on
Program Change #1
Program Change #2
Program Change #3
Program Change #4
Program Change #5
Program Change #6
Program Change #7
Program Change #8
Program Change #11
Program Change #12
Program Change #13
Program Change #14
Program Change #15
Program Change #16
Program Change #17
Program Change #18
Program Change #19
Program Change #20
any MIDIController(except BankController 0/32)
Rem
(1)
(2)
(2)
(2)
(2)
(3)
(3)
(4)
(4)
(5)
(5)
(5)
(5)
(6)
(6)
(6)
(6)
(7)
(7)
(8)
Comment
CV3=volume
CV3=volume*velocity
CV4=Ctr.#X
CV4=Ctr.#X*velocity
velocity resolution 0-127
velocity 2 steps (</>100)
velocity resolution 0-127
velocity 2 steps (</>100)
The factory setting of all parameters is described on page 6.
Whenever the MCV4 receives one of the MIDI messages listed in the table above the
parameter in question is changed and the MCV4 returnes to the normal play mode, i.e. the
LED stops flashing. Pay attention that not unintentional MIDI messages appear while beeing
in the learn mode (e.g. from a sequencer) as you change the settings of the MCV4 with such
MIDI messages. All parameter changes made while beeing in the learn mode are stored non
volatile in the MCV4 parameter memory. When the MCV4 is turned on next time the
parameter settings are taken from this memory.
Remarks
(1) MIDI channel/reference for CV1=0V
In case of an incoming note event in the learn mode the note number and the channel of the
event are taken over as the new REFERENCE NOTE and MIDI CHANNEL of the MCV4.
The reference note is the MIDI note number that belongs to 0V CV1 output. In practice you
simply enter the learn mode and press the key on your MIDI keyboard that should belong to
0V CV1. MIDI note events below the reference note or more than 5 octaves above the
reference note are ignored as the CV1 voltage range of the MCV4 is 0...+5V. The factory
default settings of reference note and MIDI channel are 36 (C) and 1.
(2)...(6)
For the setting of these parameters MIDI Program Change messages coming from your
MIDI device are used. Normally you will have to press the program change keys on your
MIDI keyboard or MIDI synthesizer while beeing in the learn mode. Pay attention that some
manufacturers count the MIDI program change numbers from 0....127 rather than 1...128 as
usual and defined in the MIDI standard. If the lowest program change number you can send
with your MIDI device is 0 (zero) you have to subtract 1 from the program change numbers in
MCV4 User's Guide - Page 4
the table above as in this case the program changes of your device range from 0...127
instead of 1...128. For some devices (especially software sequencers) the type of program
change numbering can be selected. In this case you should use the 1...128 range to agree
with the numbers in the table above.
The program change messages must be sent on the MCV4 MIDI channel (see remark 1).
(2) Velocity on/off
These program change messages are used to select whether the note on velocity affects the
control voltages CV3 resp. CV4. If velocity is "off" only volume (CV3) resp. the free chosen
controller (CV4) is used to generate the control voltage. If velocity is "on" the volume or
controller value is multiplied with the note on velocity, i.e. the CV value changes with every
new note event as the velocity of the note event is used to calculate the control voltage
together the volume message (CV3) resp. the free controller (CV4).
(3) Retrigger on/off
With this parameter you may select whether a new gate/trigger pulse is generated when
playing LEGATO (i.e. playing a new note on the keyboard while the key of the former note is
still pressed). The factory default setting is retrigger off. Additionally the MIDI controllers
LEGATO (controller #68) and SUSTAIN (controller #64) affect the gate output in the usual
manner.
(4) Trigger polarity
If voltage gate is selected with the jumper inside the MCV4 you may switch between normal
gate (i.e. +5V/+U if key is pressed and 0V if key is released) and inverted gate (i.e. 0V if key
is pressed and +5V/+U if key is released). In case of S-Trigger (jumper removed) the
circumstances are reverse. If the behaviour of your synthesizer is opposite as desired (i.e.
the sound appears if the key is released on your MIDI keyboard) you have to change this
parameter with program change #7 or #8 in the learn mode. The factory default setting is
normal gate.
(5) Velocity mode
This parameter defines whether the velocity resolution 127 steps (as in MIDI usual) or only 2
steps. The 2-step-mode is similiar to the accent used in some vintage equipment (e.g.
TB303, TR808) and could make sense to simulate one of these devices.
The velocity threshold value is 100: incoming velocity values of 100 or more are converted
into a fixed velocity value 127, incoming velocity values less than 100 are converted into a
fixed velocity value 64.
(6) CV1 key assign modes
These program change messages adjust the type of assign modes for CV1. If highest note is
selected the highest key pressed on the MIDI keyboard is used to calculated CV1 if more
than one key is pressed down. In the last note mode always the last note (chronological) is
taken for CV1. Reference note means that only the reference note is accepted. This feature
is useful if you want to trigger different devices on the same MIDI channel using two or more
MCV4. In this case you have to set the reference notes for the MCV4's to different values.
Stack note means that the MCV4 is filtering out the note event that is used by the MCV4 to
generate CV1. The note event in question is not transmitted to the MIDI Thru output. Stack
mode is used to control more than one synthesizer on one MIDI channel and enables
polyphonic control of different synthesizers on the same MIDI channel.
(7) CV Characteristics
With programm change #19 and #20 in learn mode you may select between V/Octave and
Hz/V characteristics for the CV1 output.
V/Octave is used by most of the synthesizer manufacturers (Moog, ARP, Oberheim, roland,
Sequential Circuits, EMS, Doepfer). When V/Octave is chosen incoming MIDI pitch bend
events affect the CV1 voltage. If Hz/V is selected incoming MIDI pitch bend events do not
affect the CV 1 putput. Because of the non linear voltage range mode the resolution is very
poor in the lower voltage range compared to the V/Octave. So the Hz/V mode should be
MCV4 User's Guide - Page 5
selected only if there is no other solution. The Korg synthesizer MS20 (MS10) e.g. are
equipped with external control inputs taht can be adjusted to V/Octave with the control knob.
(Input: TOTAL, (FREQ) knob:, MG/T.EXT, (EG1/EXT) ).
Using this input(s) we obtained much better results than with the Hz/V control inputs.
Also the MS20/10 has inverted trigger, so you had to switch to inverte trigger with program
change #8.
(8) Controller for CV4
If the MCV4 receives a MIDI controller message (except bank controller 0 & 32) while being
in the learn mode the controller no. of these message defines the controller no. for CV4. I.e.
the CV4 output of the MCV4 corresponds from now on to these controller no. The controller
message must be sent on the MCV4 MIDI channel (see remark 1).
Temporary parameter changes
The program change messages listed in the table can be used to change the settings only
temporary. This means that the changes are not stored in the parameter memory. If the
MCV4 is turned off and on the previous parameter settings are called up again. This
procedure may be used to try out different settings without storing them into the memory or
to change the settings temporary from a sequencer (e.g. retrigger on/off, assign mode
change).
The program change messages must be sent on the MCV4 MIDI channel (see remark 1).
Resetting the device
To obtain the factory settings for all parameters one has to reset the device. This might be
useful if you e.g. do not remember the last parameter settings (e.g. MIDI channel, reference
note, controller # for CV4, key assign mode, CV1 characteristics) or if they are misadjusted
wrongly. If your MCV4 seems to behave strange and you do not know how to solve the
problem resetting the device may help as the values of all parameters are known after the
reset. To reset the device one has to operate the learn button while the power supply is
plugged in. The LED will turn on and one has to keep down the button a few seconds until
the LED starts to flash. Operating the button once again leads to the normal operation mode
and the LED will turn off.
After the reset the MCV4 parameters are set to these values:
•
•
•
•
•
•
•
•
MIDI channel 1
reference note 36 (i.e. the lowest "c" on a standard 5-octave keyboard)
trigger polarity: normal (non-inverted)
retrigger: off
CV3: volume (controller #7)
CV4: modulation (controller #1)
CV1 characteristics: V/octave
key assign mode: highest note
These values are identical to the factory settings.
MCV4 User's Guide - Page 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement