TK-3301 - Best4Systems
INSTRUCTION MANUAL
MODE D’EMPLOI
MANUAL DE INSTRUCCIONES
MANUALE DI ISTRUZIONI
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
KULLANIM KILAVUZU
TK-3301
UHF FM TRANSCEIVER
ÉMETTEUR-RÉCEPTEUR FM UHF
TRANSCEPTOR FM UHF
RICETRASMETTITORE FM UHF
UHF-FM-TRANSCEIVER
UHF FM ZENDONTVANGER
UHF FM EL TELSİZİ
© B62-2154-20 (E, T)
09 08 07 06 05 04 03 02
UHF FM TRANSCEIVER
INSTRUCTION MANUAL
This equipment complies with the essential requirements of
Directive 1999/5/EC.
ENGLISH
TK-3301
THANK YOU
We are grateful for your purchase of this Kenwood product and
welcome you to the Private Mobile Radio service (PMR 446).
PMR is a mobile communication system for both business and
personal use without the need for a license and with no call
charges.
Your Kenwood 2-way Private Radio is called a “transceiver”,
meaning “transmitter & receiver”. We believe this easy-touse transceiver will provide you with dependable and reliable
communications. This Kenwood transceiver is a precision
device. Treat it with care, and you will enjoy years of reliable
operation.
FEATURES
•
•
•
•
16 channels with 8 operating frequencies and 38 tone/ code
settings for each channel allows you to ignore unwanted calls.
Built in voice scrambler gives you complete privacy for your
conversations.
Hands free operation when using an optional headset.
Voice announcement lets you know which channel you
have selected and which settings you have made when
reassigning key functions and channel settings.
OPERATING CONDITIONS
Open locations (no obstructions)
Up to 6.4 km
Residential areas (near buildings)
Up to 2.4 km
In steel/ concrete reinforced buildings
Up to 18,580 m2
In high rises
Up to 15 floors
Note: The listed ranges are based on field testing and may vary
with your operating conditions and individual transceiver.
NOTICES TO THE USER
◆ Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆ Illegal operation is punishable by fine and/or imprisonment.
◆ Refer service to qualified technicians only.
Safety: It is important that the operator is aware of, and
understands, hazards common to the operation of any
transceiver.
Information on Disposal of Old Electrical and Electronic Equipment and Batteries
(applicable for EU countries that have adopted separate waste collection systems)
Products and batteries with the symbol (crossed-out wheeled bin) cannot be
disposed as household waste.
Old electrical and electronic equipment and batteries should be recycled at
a facility capable of handling these items and their waste byproducts.
Contact your local authority for details in locating a recycle facility nearest
to you.
Proper recycling and waste disposal will help conserve resources whilst
preventing detrimental effects on our health and the environment.
Notice: The sign "Pb" below the symbol for batteries indicates that this
battery contains lead.
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded
in Kenwood product memories are reserved for JVC KENWOOD
Corporation.
i
PRECAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
Do not charge the transceiver and battery pack when they are wet.
Ensure that there are no metallic items located between the
transceiver and the battery pack.
Do not use options not specified by Kenwood.
If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts.
If a headset or headphone is connected to the transceiver, reduce
the transceiver volume. Pay attention to the volume level when
turning the squelch off.
Do not place the microphone cable around your neck while near
machinery that may catch the cable.
Do not place the transceiver on unstable surfaces.
Ensure that the end of the antenna does not touch your eyes.
When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these locations
when replacing the battery pack.
Do not immerse the transceiver in water.
Always switch the transceiver power off before installing optional
accessories.
The charger is the device that disconnects the unit from the AC
mains line. The AC plug should be readily accessible.
ii
Turn the transceiver power off in the following locations:
• In explosive atmospheres (inflammable gas, dust particles,
metallic powders, grain powders, etc.).
• While taking on fuel or while parked at gasoline service stations.
• Near explosives or blasting sites.
• In aircrafts. (Any use of the transceiver must follow the instructions
and regulations provided by the airline crew.)
• Where restrictions or warnings are posted regarding the use of
radio devices, including but not limited to medical facilities.
• Near persons using pacemakers.
•
•
•
•
•
•
•
•
•
Do not disassemble or modify the transceiver for any reason.
Do not place the transceiver on or near airbag equipment while
the vehicle is running. When the airbag inflates, the transceiver
may be ejected and strike the driver or passengers.
Do not transmit while touching the antenna terminal or if
any metallic parts are exposed from the antenna covering.
Transmitting at such a time may result in a high-frequency burn.
If an abnormal odor or smoke is detected coming from the
transceiver, switch the transceiver power off immediately, remove
the battery pack from the transceiver, and contact your Kenwood
dealer.
Use of the transceiver while you are driving may be against traffic
laws. Please check and observe the vehicle regulations in your
area.
Do not expose the transceiver to extremely hot or cold conditions.
Do not carry the battery pack (or battery case) with metal objects,
as they may short the battery terminals.
Danger of explosion if the battery is incorrectly replaced; replace
only with the same type.
When operating the transceiver in areas where the air is dry, it is
easy to build up an electric charge (static electricity). When using
an earphone accessory in such conditions, it is possible for the
transceiver to send an electric shock through the earphone and to
your ear. We recommend you use only a speaker/microphone in
these conditions, to avoid electric shocks.
iii
Information concerning the battery pack:
The battery pack includes flammable objects such as organic
solvent. Mishandling may cause the battery to rupture
producing flames or extreme heat, deteriorate, or cause other
forms of damage to the battery. Please observe the following
prohibitive matters.
•
•
•
•
•
•
Do not disassemble or reconstruct battery!
The battery pack has a safety function and protection circuit to
avoid danger. If they suffer serious damage, the battery may
generate heat or smoke, rupture, or burst into flame.
Do not short-circuit the battery!
Do not join the + and – terminals using any form of metal (such
as a paper clip or wire). Do not carry or store the battery pack in
containers holding metal objects (such as wires, chain-necklace or
hairpins). If the battery pack is short-circuited, excessive current will
flow and the battery may generate heat or smoke, rupture, or burst
into flame. It will also cause metal objects to heat up.
Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is
damaged, or the electrolyte is ignited, the battery may generate
heat or smoke, rupture, or burst into flame.
Do not use or leave the battery near fire, stoves, or other heat
generators (areas reaching over 80°C/ 176°F)!
If the polymer separator is melted due to high temperature, an
internal short-circuit may occur in the individual cells and the
battery may generate heat or smoke, rupture, or burst into flame.
Do not immerse the battery in water or get it wet by other
means!
If the battery’s protection circuit is damaged, the battery may
charge at extreme current (or voltage) and an abnormal chemical
reaction may occur. The battery may generate heat or smoke,
rupture, or burst into flame.
Do not charge the battery near fire or under direct sunlight!
If the battery’s protection circuit is damaged, the battery may
charge at extreme current (or voltage) and an abnormal chemical
reaction may occur. The battery may generate heat or smoke,
rupture, or burst into flame.
iv
•
•
•
•
•
•
•
Use only the specified charger and observe charging
requirements!
If the battery is charged in unspecified conditions (under high
temperature over the regulated value, excessive high voltage or
current over regulated value, or with a remodeled charger), it may
overcharge or an abnormal chemical reaction may occur. The
battery may generate heat or smoke, rupture, or burst into flame.
Do not pierce the battery with any object, strike it with an
instrument, or step on it!
This may break or deform the battery, causing a short-circuit. The
battery may generate heat or smoke, rupture, or burst into flame.
Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or smoke,
rupture, and/or burst into flame. If the battery’s protection circuit
is damaged, the battery may charge at an abnormal current (or
voltage), and an abnormal chemical reaction may occur. The
battery may generate heat or smoke, rupture, or burst into flame.
Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into
flame.
Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function
is damaged, the battery may generate heat or smoke, rupture, or
burst into flame.
Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical reaction
may occur. In some cases, an unexpected large amount of
current may flow upon discharging. The battery may generate
heat or smoke, rupture, or burst into flame.
Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery
pack does not smoothly connect with a charger or operating
equipment, do not force it; check the polarity of the battery. If the
battery pack is reverse-connected to the charger, it will be reversecharged and an abnormal chemical reaction may occur. The
battery may generate heat or smoke, rupture, or burst into flame.
v
•
Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash
your eyes with fresh water as soon as possible, without rubbing
your eyes. Go to the hospital immediately. If left untreated, it may
cause eye-problems.
•
Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the
regulated time has passed, stop it. The battery may generate heat
or smoke, rupture, or burst into flame.
Do not place the battery pack into a microwave or high
pressure container!
The battery may generate heat or smoke, rupture, or burst into
flame.
Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor),
immediately remove it from flammable areas. Electrolyte leaking
from battery can easily catch on fire and may cause the battery to
generate smoke or burst into flame.
Do not use an abnormal battery!
If the battery pack emits a bad odor, appears to have different
coloring, is deformed, or seems abnormal for any other reason,
remove it from the charger or operating equipment and do not use
it. The battery may generate heat or smoke, rupture, or burst into
flame.
•
•
•
vi
CONTENTS
UNPACKING AND CHECKING EQUIPMENT.......................... 1
PREPARATION .......................................................... 2
ORIENTATION ........................................................... 6
BASIC OPERATIONS ................................................... 8
VOICE OPERATED TRANSMISSION (VOX) .......................... 9
BACKGROUND OPERATIONS ........................................ 10
CHANNEL SETUP MODE.............................................. 11
KEY ASSIGNMENT MODE ............................................ 17
TROUBLESHOOTING GUIDE ......................................... 21
OPTIONAL ACCESSORIES ............................................ 22
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the transceiver. If any of the items listed
below are missing or damaged, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
•
•
•
•
•
•
Battery charger/ AC adapter (KSC-35 or KSC-35S)............... 1
Li-ion Battery pack (KNB-45L) ................................................ 1
Speaker/ microphone jack cover ............................................ 1
Speaker/ microphone locking bracket .................................... 1
Belt clip (KBH-10) ................................................................... 1
Screw set
•
•
M2.6 x 7 mm (Black) ............................................................... 1
M3 x 8 mm .............................................................................. 2
• Instruction manual .................................................................. 1
Note: Refer to "PREPARATION" for accessory installation
instructions.
1
PREPARATION
INSTALLING/ REMOVING THE BATTERY PACK
◆ Do not short the battery terminals or dispose of the battery by
fire.
◆ Never attempt to remove the casing from the battery pack.
1 Align the battery pack with the
back of the transceiver, then
press the battery pack and
transceiver firmly together until
the release latch on the base of
the transceiver locks.
2 To remove the battery pack, lift
the safety catch on the base of
the transceiver, then press the
release latch underneath the
safety catch.
3 While pressing the release
latch, pull the battery pack
away from the transceiver.
2
INSTALLING THE BELT CLIP
If necessary, attach the belt clip using
the two supplied M3 x 8 mm screws.
Note: If the belt clip is not installed, its
mounting location may get hot during
continuous transmission or when left
sitting in a hot environment.
Belt clip
Do not use glue which is designed to prevent screw loosening when
installing the belt clip, as it may cause damage to the transceiver.
Acrylic ester, which is contained in these glues, may crack the
transceiver’s back panel.
INSTALLING THE COVER OVER THE SPEAKER/ MICROPHONE
JACKS
If you are not using a speaker/
microphone, install the cover over
the speaker/ microphone jacks using
the supplied M2.6 x 7 mm screw.
Note: To keep the transceiver water
resistant, you must cover the speaker/
microphone jacks with the supplied
cover.
Speaker/ microphone
jack cover
3
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE
(OR HEADSET)
1
2
Insert the speaker/ microphone
(or headset) plugs into the
speaker/ microphone jacks.
Attach the locking bracket using
the supplied M2.6 x 7 mm screw.
Note: The transceiver is not fully
water resistant while using the
speaker/ microphone.
Speaker/ microphone
locking bracket
CHARGING THE BATTERY PACK
The battery pack is not charged at the factory; charge it before
use.
Average battery pack life (calculated using 5% transmit time, 5%
receive time, and 90% standby time) is 20 hours.
ATTENTION: Always switch OFF a transceiver equipped with a
battery pack before inserting the transceiver into the charger.
1 Plug the AC adapter cable into
the jack located on the rear of the
charger.
2 Plug the AC adapter into an AC
outlet.
4
3 Slide a battery pack or a
transceiver equipped with a battery
pack into the charging slot of the
charger.
•
•
Charging slot
Indicator
Make sure the metal contacts of the
battery pack mate securely with the
charger terminals.
The indicator lights red and
charging begins.
4 When charging is completed, the
indicator lights green. Remove
the battery pack or the transceiver
from the charging slot of the
charger.
•
•
It takes approximately 3 hours to
charge the battery pack.
When the charger will not be used
for a long time, unplug the AC
adapter from the AC outlet.
Note:
◆ When the indicator blinks red, the battery pack is either
defective or the battery pack contacts are not properly mated
with those of the charger.
◆ When the indicator flashes green and orange, the battery pack
has not satisfied the charging start temperature. Remove the
battery pack from the charger and wait until it reaches a normal
temperature before charging it again. <KSC-35S only>
◆ The ambient temperature should be between 5°C and 40°C
while charging is in progress. Charging outside this range may
not fully charge the battery.
◆ The battery pack life is over when its operating time decreases
even though it is fully and correctly charged. Replace the
battery pack.
5
ORIENTATION
Antenna
Battery pack
Channel selector
Rotate to change the operating channel.
•
•
To change the operating frequency or QT/DQT settings of a
channel, refer to “CHANNEL SETUP MODE” on page 11.
Channel Annunciation: When changing channels, the
transceiver will announce the newly selected channel number.
(This can be deactivated by your dealer.)
LED indicator
For the LED indicator status, refer to page 7.
Power switch/ Volume control
Turn clockwise to switch the transceiver ON. To switch the
transceiver OFF, turn counterclockwise until a click sounds.
Rotate to adjust the volume level.
PTT (Push to Talk) switch
Press and hold, then speak into the microphone to transmit.
6
Side 1 key
Press to activate its programmable function.
The default setting is Calling Alert.
•
For function descriptions and details on how to change the
function of the Side 1 key, refer to “KEY ASSIGNMENT MODE”
on page 17.
Side 2 key
Press to activate its programmable function.
The default setting is Squelch Off Momentary.
•
For function descriptions and details on how to change the
function of the Side 2 key, refer to “KEY ASSIGNMENT MODE”
on page 17.
Speaker/ microphone jacks
Insert the Speaker/ microphone or Headset plug into this
jack.
LED Indicator Status
Indicator Color
Meaning
Lights red
Transmitting
Lights green
Receiving a call
Blinks red
Battery power is low while transmitting
Blinks green
Scanning
Blinks red/orange
The selected channel has not been
programmed and cannot be used.
7
BASIC OPERATIONS
1 Turn the Power switch/ Volume control
clockwise to switch the transceiver power
ON.
•
A beep sounds if enabled by your dealer.
2 Press the key programmed with the Monitor
or Squelch Off (Side 2 key default) function
to hear background noise, then rotate the
Power switch/ Volume control to adjust the
volume.
3
Rotate the Channel selector to select your
desired channel.
•
When you receive an appropriate signal, you
will hear audio from the speaker.
4 To make a call, press and hold the PTT
switch, then speak into the microphone using
your normal speaking voice.
•
Hold the microphone approximately 3 to 4 cm
(1.5 inches) from your lips.
5 Release the PTT switch to receive.
Note: When the battery pack voltage becomes too low, transmission
will stop and an alert tone will sound.
8
VOICE OPERATED TRANSMISSION (VOX)
VOX operation allows you to transmit hands-free. VOX can
only be used if you are using a supported headset. This
function can be turned off for specific channels by your dealer.
To activate VOX and set the VOX Gain level, perform the
following steps:
1 Connect the headset to the transceiver .
•
The VOX function does not activate when a headset is not
connected to the accessory terminal of the transceiver.
2 With the transceiver power OFF, press and hold the Side 1
key while turning the transceiver power ON.
3 Continue to hold the Side 1 key until a beep sounds.
•
•
The LED indicator lights turn orange.
When the Side 1 key is released, the transceiver will announces
the VOX Gain level.
4 Press the Side 1 key to increase the VOX Gain level and
the Side 2 key to decrease the level.
•
•
The VOX Gain level can be adjusted from level 1 to 10 and OFF.
The transceiver announces the VOX Gain level as you adjust it.
If OFF is selected, a beep sounds.
5 Press the PTT switch to save the setting.
•
•
A beep will sound.
The transceiver announces the new VOX Gain level.
6 Turn the transceiver power OFF and then ON again to
activate VOX.
Note:
◆ If a headset is connected to the transceiver while the VOX
function is switched ON and the VOX Gain level is configured
to a higher, more sensitive level, louder received signals may
cause the transceiver to start transmission.
◆ The transceiver will automatically return to normal operation if
no action is performed for 5 seconds.
9
BACKGROUND OPERATIONS
TIME-OUT TIMER (TOT)
The Time-out Timer prevent callers from using a channel for
an extended duration. If you continuously transmit for the
duration programmed by your dealer (default is 60 seconds),
transmission will stop and an alert tone will sound. To stop the
tone, release the PTT switch.
BATTERY SAVER
When activated by your dealer, the Battery Saver function
decreases the amount of power used after no signal is present
and no operations are being performed for 5 seconds. When a
signal is received or an operation is performed, Battery Saver
turns off.
Note: While the Battery Saver is operating, the LED may flash
green when receiving a QT/DQT signal which does not match the
QT/DQT tone/code set up in your transceiver.
LOW BATTERY WARNING
While operating the transceiver, the Low Battery Warning
sounds an alert tone every 30 seconds and the LED indicator
blinks red when the battery needs recharged or replaced.
CHANNEL ANNUNCIATION
When changing the channel, the transceiver will announce the
newly selected channel number. Likewise, the transceiver will
announce the current channel after you turn the transceiver
power ON. (Channel Annunciation can be activated or
deactivated by your dealer.)
10
CHANNEL SETUP MODE
This transceiver allows you to reprogram each of the channels
with different frequencies and QT (Quiet Talk)/ DQT (Digital
Quiet Talk) settings. The table below lists the default channel
settings.
Channel
Number
Table
Number
Frequency (MHz)
Tone
Number
QT/DQT Setting
1
1
446.00625
10
94.8 Hz
2
8
446.09375
08
88.5 Hz
3
3
446.03125
13
103.5 Hz
4
6
446.06875
05
79.7 Hz
5
4
446.04375
17
118.8 Hz
6
2
446.01875
18
123.0 Hz
7
7
446.08125
19
127.3 Hz
8
5
446.05625
07
85.4 Hz
9
1
446.00625
14
107.2 Hz
10
8
446.09375
15
110.9 Hz
11
3
446.03125
16
114.8 Hz
12
6
446.06875
06
82.5 Hz
13
4
446.04375
27
D132N
14
2
446.01875
28
D155N
15
5
446.05625
29
D134N
16
7
446.08125
30
D243N
Note: You must first select an operating frequency for a channel
before you can select a QT/ DQT setting for that same channel.
11
CHANNEL OPERATING FREQUENCIES
To change the operating frequency of a channel:
1 With the transceiver power OFF, press and hold the PTT
switch and Side 1 key while turning the transceiver power
ON.
•
Continue to hold the PTT switch and Side 1 key until the LED
lights orange and the transceiver announces “Self”.
2 Release the PTT switch and Side 1 key.
•
The transceiver announces “Channel”.
3 Press and release the PTT switch, then rotate the Channel
selector to your desired channel.
•
Upon pressing and releasing the PTT switch, a beep will sound
and the transceiver announces “Table zero”.
4 Press the Side 1 or Side 2 key to increment/ decrement the
Table number, to select the new channel frequency.
•
•
Table numbers and their corresponding operating frequencies
are provided in the table on page 13.
A voice announcement will inform you of the currently selected
Table number.
5 Press the PTT switch to save the setting.
•
•
A beep will sound.
Repeat steps 3 to 5 to set up another channel.
6 Turn the transceiver power OFF and then ON again to
activate the new settings.
Note: The transceiver will automatically return to normal operation
if no action is performed for 5 seconds.
12
Table Number
Operating
Frequency
Table Number
Operating
Frequency
0
OFF
1
2
446.00625 MHz
5
446.05625 MHz
446.01875 MHz
6
446.06875 MHz
3
446.03125 MHz
7
446.08125 MHz
4
446.04375 MHz
8
446.09375 MHz
QT/ DQT SETTINGS
Quiet Talk (QT) and Digital Quiet Talk (DQT) are functions that
reject undesired signals on your channel. You will hear a call
only when you receive a signal that contains a matching QT
tone or DQT code. If a call containing a different tone or code
is received, squelch will not open and you will not hear the call.
Likewise, when transmitting using QT or DQT, the receiving
station must have a matching tone or code to hear your call.
Be aware that other parties can still hear your calls if they set
up their transceiver with the same tone or code.
The default QT/DQT settings for each channel are provided in
the table on page 15.
To change the QT/DQT settings of a channel:
1 With the transceiver power OFF, press and hold the PTT
switch and Side 1 key while turning the transceiver power
ON.
•
Continue to hold the PTT switch and Side 1 key until the LED
lights orange and the transceiver announces “Self”.
2 Release the PTT switch and Side 1 key.
•
The transceiver announces “Channel”.
3 Press the Side 1 or Side 2 key to select QT/DQT setup.
•
The transceiver announces “Tone”.
13
4 Press and release the PTT switch, then rotate the Channel
selector to your desired channel.
•
Upon pressing and releasing the PTT switch, a beep will sound
and the transceiver announces “Tone one”.
5 Press the Side 1 or Side 2 key to increment/ decrement the
Tone number, to select the new tone or code.
•
•
•
QT/DQT table numbers and their corresponding tones/ codes
are provided in the table on page 15.
Press and hold the Side 1 or Side 2 key to increment/
decrement the Tone number by 5 at a time.
A voice announcement will inform you of the currently selected
Tone number.
6 Press the PTT switch to save the setting.
•
•
A beep will sound.
Repeat steps 4 to 6 to set up another channel.
7 Turn the transceiver power OFF and then ON again to
activate the new settings.
Note: The transceiver will automatically return to normal operation
if no action is performed for 5 seconds.
14
Tone
Number
QT/DQT
Setting
Tone
Number
QT/DQT
Setting
Tone
Number
QT/DQT
Setting
1
67.0 Hz
14
107.2 Hz
27
D132N
2
71.9 Hz
15
110.9 Hz
28
D155N
3
74.4 Hz
16
114.8 Hz
29
D134N
4
77.0 Hz
17
118.8 Hz
30
D243N
5
79.7 Hz
18
123.0 Hz
31
D311N
6
82.5 Hz
19
127.3 Hz
32
D346N
7
85.4 Hz
20
131.8 Hz
33
D315N
8
88.5 Hz
21
136.5 Hz
34
D351N
9
91.5 Hz
22
141.3 Hz
35
D423N
10
94.8 Hz
23
146.2 Hz
36
D664N
11
97.4 Hz
24
151.4 Hz
37
D431N
12
100.0 Hz
25
156.7 Hz
38
D723N
13
103.5 Hz
26
162.2 Hz
Off
OFF
Note: The Tone numbers corresponding to the QT/DQT values can
be changed by your dealer.
15
CHANNEL CONFIRMATION MODE
To confirm your channel settings:
1 With the transceiver power OFF, press and hold the PTT
switch while turning the transceiver power ON.
•
Continue to hold the PTT switch until the LED lights orange and
the transceiver announces “Confirm”.
2 Release the PTT switch.
•
The transceiver announces the channel table number and Tone
number of the selected channel.
3 Rotate the Channel selector to your desired channel within
5 seconds, otherwise the operation will cancel.
•
The transceiver announces the channel table number and Tone
number of the current channel.
Note: The transceiver will automatically return to normal operation
if no action is performed for 5 seconds.
16
KEY ASSIGNMENT MODE
This transceiver allows you to reprogram the Side 1 and Side
2 keys with any of the functions listed in the table below.
Explanations on the use of each function are provided under
“PROGRAMMABLE FUNCTIONS”, on page 19.
Table Number
0
Function Name
None (no function)
1
Calling Alert (Side 1 key default)
2
Key Lock
3
Key Lock Status Memory
4
Monitor
5
Monitor Momentary
6
Scan
7
Scan + Temporary Delete
8
Scrambler
9
Squelch Off
10
Squelch Off Momentary (Side 2 key default)
11
Temporary Delete
17
To change the functions of the Side 1 and Side 2 keys:
1 With the transceiver power OFF, press and hold the Side 1
and Side 2 keys while turning the transceiver power ON.
•
Continue to hold the Side 1 and Side 2 keys until the LED lights
orange and the transceiver announces “Setup”.
2 Continue to press and hold the key to be reprogrammed
(either the Side 1 or Side 2 key), while releasing the
remaining key.
•
•
The transceiver will announce “Table zero”.
If you continue to hold both keys, or if you release both keys,
the operation will cancel in 5 seconds.
3 Release the key.
4 Press the Side 1 or Side 2 key to increment/ decrement the
number, to select the new key function.
•
•
Table numbers and their corresponding functions are provided
in the table on page 17.
A voice announcement will inform you of the currently selected
Table number.
5 Press the PTT switch to save the setting.
•
A beep will sound and the transceiver will announce the new
Table number.
6 Turn the transceiver power OFF and then ON again to
activate the new settings.
Note: The transceiver will automatically return to normal operation
if no action is performed for 5 seconds.
18
PROGRAMMABLE FUNCTIONS
■ Calling Alert (Side 1 key default)
Calling alert tones help identify yourself to party members
and inform them that you are calling. Your dealer can set
up your transceiver with 1 of 10 calling alert tones. If each
party member uses a different tone, it is easy to know who
is calling. To make a call, press and hold the PTT switch,
then press the key programmed as Calling Alert.
•
Release the key to end the tone.
■ Key Lock
Press and hold this key for 1 second to lock/ unlock the
transceiver keys.
The following keys/ functions can still be used when Key
Lock is active:
Calling Alert, Key Lock, Monitor, Monitor Momentary,
PTT, Squelch Off, Squelch Off Momentary, and Volume.
■ Key Lock with Status Memory
This operates the same as Key Lock except that when the
transceiver power is turned OFF and then ON again, the
keys remain locked. Without Status Memory, when the
transceiver power is turned OFF and then ON again, the
Key Lock function will be cancelled.
■ Monitor
Momentarily press this key to deactivate QT or DQT
signaling. Press the key again to return to normal operation.
■ Monitor Momentary
Press and hold this key to deactivate QT or DQT signaling.
Release the key to return to normal operation.
19
■ Scan
Press this key to start scanning the transceiver channels.
Priority Scan: The Priority channel is a channel that is
given first priority to while scanning. The Priority channel is
set by your dealer.
Revert Channel: During Scan, pressing the PTT switch will
automatically select the transceiver’s Revert channel and
you will begin transmitting. Your dealer can program the
Revert channel using one of the following methods:
• Selected
• Selected + Talkback
• Priority
• Priority + Talkback
■ Scan + Temporary Delete
Press this key to start scanning the transceiver channels.
When Scan pauses at an undesired channel, you can
remove that channel from the scanning sequence by
pressing and holding this key for 3 seconds.
■ Scrambler
The Scrambler function allows you to hold a conversation in
complete privacy. When the Scrambler function is activated,
any other party that is listening to your channel will be
unable to understand your conversation.
■ Squelch Off
Momentarily press this key to hear background noise. Press
the key again to return to normal operation.
■ Squelch Off Momentary (Side 2 key default)
Press and hold this key to hear background noise. Release
the key to return to normal operation.
■ Temporary Delete
When Scan pauses at an undesired channel, you can
remove that channel from the scanning sequence by
pressing and holding this key for 1 second.
20
TROUBLESHOOTING GUIDE
Problem
Solution
•
Cannot turn the
transceiver power ON.
Battery power dies shortly
after charging.
Cannot talk to or hear
other members in your
group.
•
•
The battery pack life is finished.
Replace the battery pack with a
new one.
•
Make sure you are using the
same frequency and QT/DQT
settings as the other members in
your group.
Other group members may be
using the Scrambler function. Turn
on your transceiver’s Scrambler.
Other group members may be
too far away. Make sure you
are within range of the other
transceivers.
•
•
•
Other voices (besides
group members’) are
present on the channel.
The battery pack may be dead.
Recharge or replace the battery
pack.
The battery pack may not be
installed correctly. Remove the
battery pack and install again.
Change the QT/DQT settings.
Make sure all group members
change the settings on their
transceivers to match the new
QT/DQT setting.
21
OPTIONAL ACCESSORIES
•
•
•
•
•
•
•
•
•
•
KMC-21 (Speaker/ microphone)
KMC-45 (Speaker/ microphone)
KHS-1 (Headset)
KHS-21 (Headset)
KNB-45L (Li-ion battery pack)
KSC-35 (Rapid charger)
KSC-35S (Rapid charger)
KSC-356 (Multiple charger)
KBH-10 (Belt clip)
KWR-1 (Water resistant bag)
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising