1. Power Button 2. Band Switch 3. Function Switch (AUX/CD/TAPE/RADIO) 4. Bass Boost Button 5. CD Mode Button 6. CD Program Button 7. CD Stop Button 8. CD Play/Pause Button 9. CD Skip/Search Forward Button 10. CD Skip/Search Backward Button 11. Volume Control Knob 12. Tuning Knob 13. Dial Pointer 14. CD LCD Display 15. Remote Sensor 16. Power/Standby LED Indicator 17. FM Stereo LED Indicator 18. Radio Functional Indicator 19. Tape Functional Indicator 20. CD Functional Indicator 21. Cassette Compartment 22. Aux Jack 23. Cassette Record Button 24. Cassette Play Button 25. Cassette Rewind Button 26. Cassette Fast Forward Button 27. Cassette Stop/Eject Button 28. Cassette Pause Button 29. Stereo Headphone Jack 30. Cassette Key Control Door 31. Speaker Terminal (L/R) 32. AC Power Cord 33. FM Antenna 34. CD Door 35. Speaker Box Left 36. Speaker Box Right 37. Folder Down Button “-” 38. Folder Up Button “+” English - 1 AC OPERATION Before operating, please check carefully that the voltage indicated on your set corresponds to the voltage of your local area. 1. Plug the AC POWER CORD into a standard AC outlet. 2. Press the POWER BUTTON to start the unit. POWER/STANDBY LED INDICATOR will light up to indicate unit is connected to the power source properly. SPEAKER BOX CONNECTION Insert the Speaker plug of the SPEAKER BOXES to the SPEAKER TERMINAL on the rear of the unit. RADIO OPERATION 1. Slide the FUNCTION SWITCH to the “RADIO” position, the RADIO FUNCTIONAL INDICATOR will light up. 2. Slide the BAND SWITCH to the desired waveband. 3. Turn the TUNING KNOB to your desired radio station. 4. Adjust the sound level by pressing the VOLUME CONTROL KNOB Up or Down. 5. To turn off the radio, press the POWER BUTTON to “OFF” position. FM STEREO INDICATOR When tuned to a FM stereo broadcast the “FM ST” INDICATOR will light up. If it does not, check that the BAND SWTICH is set to “FM ST” position. In weak signal areas the FM stereo signal may not be strong enough and can cause excessive background noise. In this case, slide the BAND SWITCH to the “FM” position. ANTENNAS For best reception, fully extend the FM ANTENNA to receive FM stations. For AM reception, the unit has a built-in antenna, and it may be necessary to turn the whole unit for best reception. BASS BOOST At all volume levels, push the BASS BOOST BUTTON to “ON” position to enhance the low frequency sound. To release the super bass, simply push this button once again. STEREO HEADPHONE JACK For private listening, insert the plug of a Stereo Headphone into the STEREO HEADPHONE JACK and adjust the VOLUME CONTROL KNOB accordingly. Be English - 2 sure that your headphone has 3.5mm diameter stereo plug with an impedance of 32 ohms. During the use of a headphone, the Speakers are automatically disconnected. Cassette operation Tape Playback First of all, open the CASSETTE KEY CONTROL DOOR (30) 1. Press the STOP/EJECT BUTTON to open the cassette door. 2. Insert a pre-recorded cassette tape into the CASSETTE COMPARTMENT and close the cassette door. 3. Slide the FUNCTION SWITCH to the TAPE position, the TAPE FUNCTIONAL INDICATOR will light up. 4. Press the PLAY BUTTON. 5. Adjust the VOLUME CONTROL KNOB to your desired listening level. 6. To stop the tape, press the STOP/EJECT BUTTON. 7. To turn off the unit, press the POWER BUTTON to “OFF” position. Fast Forward and Rewind The tape can be fast forwarded or rewound by pressing the FAST FORWARD BUTTON or REWIND BUTTON respectively. Pause Function During playback or recording, the tape can be stopped temporarily by pressing the PAUSE BUTTON. To continue playback or recording, press the PAUSE BUTTON again. Auto Stop System When the tape runs to the end during playback or recording, the cassette operation will be stopped automatically. Note : When fast forwarding or rewinding, the STOP BUTTON must be pressed when the tape runs to the end. Caution To avoid damage to the cassette mechanism or to the cassette tapes, always press the STOP/EJECT BUTTON between each operation! Recording From The Radio 1. Tune to a desired radio program as described in the “RADIO OPERATION” section. 2. Insert a blank cassette tape into the CASSETTE COMPARTMENT. 3. Press the PAUSE BUTTON. English - 3 4. Press the RECORD BUTTON. The PLAY BUTTON is engaged simultaneously to start recording. With the built-in Automatic Level Control (ALC), the best recording quality is automatically adjusted. Changing the volume level will not affect the recording. Release the PAUSE BUTTON to begin recording. 5. To stop recording temporarily, press the PAUSE BUTTON. To continue the recording, press the PAUSE BUTTON once again. 6. Press the STOP/EJECT BUTTON to stop recording. 7. When the tape runs to its end, the cassette operation will be stopped automatically. CD OPERATION PLAYING COMPACT DISC (CD-R/RW PLAYBACK COMPATIBLE) Getting Started Note: Should skipping of tracks occur during CD playing, try turning the volume down. When CD is playing, do not open the CD DOOR. 1. Open the CD DOOR by pull up the CD DOOR. Put a CD disc into the CD Compartment and close the CD DOOR. Set the FUNCTION SWITCH to “CD” position, the CD LCD DISPLAY and CD FUNCTIONAL INDICATOR will light up. Note : Ensure the CD DOOR is closed properly and locked in place. 2. When the CD DOOR is closed with a CD inside, total number of the tracks in the disc will be shown on the CD LCD DISPLAY and will go to stop mode. (ex. Total 17 tracks inside the disc). 3. If there is no disc inside, the LCD DISPLAY will show “ ” and go to stop mode. 4. If the CD DOOR is not closed, the DISPLAY will show “ ”. Play/Pause Mode 1. When the PLAY/PAUSE BUTTON is pressed during CD stop mode, the first track will be played. The Play Indicator “” will be shown on the LCD DISPLAY. The CD LCD DISPLAY will show the English - 4 2. 3. 4. 5. specific number of track being played. For interruption while the CD is playing, press the CD PLAY/PAUSE BUTTON once. The Play Indicator “” will blink continuously on the LCD DISPLAY. Though the sound stops, the disc will continue to spin. To re-start playing, press the CD PLAY/PAUSE BUTTON once again. The music will start from the exact position where it was interrupted. To stop the CD, press the CD STOP BUTTON once whether the CD is in Play or Pause mode. The LCD DISPLAY will show the total number of tracks of the disc again. To turn off the unit, press the POWER BUTTON to “OFF” position. Skip And Search Mode 1. During play or pause mode, when CD SKIP/SEARCH or CD SKIP/SEARCH BUTTON is pressed once, it will go to the next track or go back to the beginning of the track. 2. During play mode, when CD SKIP/SEARCH or CD SKIP/SEARCH BUTTON is pressed and held, it will search the track with audible highspeed forward or backward playback. Repeat Mode 1. Repeat 1 : When the MODE BUTTON is pressed once, the Repeat Indicator “ ” will be shown on the LCD DISPLAY. This single track of music will be repeated. 2. Repeat All: When the MODE BUTTON is pressed twice, the Repeat All Indicator “ ” will be shown on the LCD DISPLAY. The whole disc can be played continuously. 3. To cancel the Repeat Function Press the MODE BUTTON repeatedly until the Repeat Indicator disappears from the LCD DISPLAY. Random Play Mode This feature allows the track on the disc to be played in a random order. 1. During the CD stop mode, press the MODE BUTTON three times, the “ ” indicator will English - 5 be shown on the LCD DISPLAY. Press the PLAY BUTTON once to start the playback. 2. To cancel the random play function, press the MODE BUTTON again, “ ” Indicator will disappear from the LCD DISPLAY. Program Mode 1. During the CD stop mode, press the PROGRAM BUTTON once. The Program Indicator “ ” and the number of Program to be memorized ” will light up starts from the first program “ and blink continuously. Press the CD SKIP/SEARCH or SKIP/SEARCH BUTTON to your desired musical track, the CD LCD DISPLAY will show the appropriate track number. Press the PROGRAM BUTTON to store this track in memory. 2. Repeat above procedure until all desired tracks have been programmed. A total of 20 tracks can be stored in memory. Remarks : Whenever CD SKIP/SEARCH FORWARD or BACKWARD BUTTON is pressed, it will always show the last programmed track first to recall your memory. After complete programming, LCD DISPLAY will show “ ” and flash continuously. 3. Press the CD PLAY/PAUSE BUTTON once to start the program playback and the CD Play Indicator “” will light up. 4. To check the program you have stored after complete programming, press the PROGRAM BUTTON once during CD stop mode, then press the CD SKIP/SEARCH FORWARD BUTTON once, the LCD DISPLAY will show the first programmed track number. Repeat above procedure to read all the programmed memory. 5. To cancel the programmed memory : ¾ During the CD stop mode, press the CD STOP BUTTON once. OR ¾ Open the CD DOOR during the CD stop mode. The Program Indicator “ ” will disappear from the LCD DISPLAY. English - 6 PLAYING MP3 DISC Getting Started Note: Should skipping of tracks occur during MP3 Disc playing, try turning the volume down. When MP3 disc is playing, do not open the CD DOOR. 1. Open the CD DOOR by pull up the CD DOOR. Put a MP3 disc into the CD compartment and close the CD DOOR. Set the FUNCTION SWITCH to “CD” position, the CD LCD DISPLAY and CD FUNCTIONAL INDICATOR will light up. Note : Ensure the CD DOOR is closed properly and locked in place. 2. When the CD DOOR is closed with a MP3 disc inside, total number of the tracks in the disc will be shown on the CD LCD DISPLAY and go to stop mode. 3. If there is no disc inside, the DISPLAY will show “ ” and go to stop mode. 4. If the CD DOOR is not closed, the DISPLAY will show “ ”. Play/Pause Mode 1. When the PLAY/PAUSE BUTTON is pressed during CD stop mode, the first track will be played. The Play Indicator “” will be ” Indicator will be shown as well lighted. The “ to indicate MP3 Disc is being played. The LCD DISPLAY will show the specific track number being played. 2. To select the specific musical tracks inside the MP3 Disc. MP3 music can be stored into CD Disc with or without folders according to your “MP3 burning method”. a. If the MP3 disc is downloaded without dividing into folder, all track number will be shown directly in the LCD DISPLAY. The Album number will only show after pressing the FOLDER UP or DOWN BUTTON. b. If the music is stored into different folders, then you’ve to select the specific Album number first by pressing the FOLDER UP or DOWN BUTTON ; afterwards press the CD SKIP/SEARCH FORWARD or BACKWARD BUTTON to select the specific Track number music inside this Album. English - 7 Example : To select Album # 4, track # 3. STEP – 1 : Press the FOLDER UP or DOWN BUTTON to select the Album # 4. STEP – 2 : Press the CD SKIP/SEARCH FORWARD or BACKWARD BUTTON to select the Track # 3 inside this Album # 4. 3. For interruption while MP3 disc is playing, press the CD PLAY/PAUSE BUTTON once. The Play Indicator “” will blink continuously on the LCD DISPLAY. 4. Though the sound stops, the disc will continue to spin. To re-start playing, press the CD PLAY/PAUSE BUTTON once again. The music will start from the exact position where it was interrupted. 5. To stop the MP3 disc, press the CD STOP BUTTON once whether the MP3 disc is in Play or Pause mode. 6. To turn off the unit, press the POWER BUTTON TO “OFF” position. Repeat Mode 1. Repeat 1 : When the MODE BUTTON is pressed once, the Repeat Indicator “ ” will light. This single track of music will be repeated. 2. Repeat Folder : When the MODE BUTTON is pressed twice, the “ ” and “ ” indicator will be shown. This specific folder will be played repeatedly. 3. Repeat All : When the REPEAT BUTTON is pressed three times, the Repeat All Indicator “ ” will be shown. The whole disc can be played continuously. 4. To cancel the Repeat Function Press the MODE BUTTON repeatedly until the Repeat Indicator disappears from the LCD DISPLAY. English - 8 Random Play Mode This feature allows the tracks on the disc to be played in a random order. 1. During the CD Stop mode, press the MODE BUTTON four times, the “ ” Indicator will show on the LCD DISPLAY. Press the PLAY/PAUSE BUTTON once to start the playback. 2. To cancel the Random Play function, press the MODE BUTTON again, “ ” Indicator will disappear from the LCD DISPLAY. Skip And Search 1. During play or pause mode, when CD SKIP/SEARCH or CD SKIP/SEARCH BUTTON is pressed once, it will go to the next track or go back to the beginning of the track. 2. During play mode, when CD SKIP/SEARCH or CD SKIP/SEARCH BUTTON is pressed once and held, it will search the track with audible high speed forward or backward playback. Program Mode 1. During the CD stop mode, press the PROGRAM BUTTON once. The Program Indicator “ ” and the number of Program to be memorized starts from the first program “ ” will light up and blink continuously. Press the FOLDER UP or DOWN BUTTON, then press CD SKIP/SEARCH FORWARD or BACKWARD BUTTON to select your desired musical track, CD LCD DISPLAY will show the track number of this specific Album to be programmed. Press the PROGRAM BUTTON to store this track in memory. 2. Repeat above procedure until all desired tracks have been programmed. Remarks : Whenever the FOLDER UP or DOWN BUTTON is pressed, it will always show the last programmed Album number first to recall your memory. A total of 10 tracks can be stored in memory. After complete programming, LCD DISPLAY will show “ ” and blink continuously. 3. To start the Programmed playback, press the CD PLAY/PAUSE BUTTON once and the CD Play Indicator “”, “ ” and the track number of the specific Album will light up. English - 9 Example : Album # 3, Track # 2. 4. To check the program you have stored after complete programming, press the PROGRAM BUTTON once during the CD Stop mode. The LCD ” and blink continuously. Press the FOLDER UP DISPLAY will show “ or DOWN BUTTON to read the Album number, then press the CD SKIP/SEARCH FORWARD or BACKWARD BUTTON to read the specific track number of said Album. Press the PROGRAM BUTTON again, LCD DISPLAY will show “ ” and blink continuously. Repeat above procedure to check all programs being stored. 5. To cancel the programmed memory : ¾ During the CD stop mode, press the CD STOP BUTTON once. OR ¾ Open the CD Door during the CD stop mode. The Program Indicator “ ” will disappear from the LCD DISPLAY. Recording From CD Player 1. Slide the FUNCTION SWITCH to “CD” position, the CD LCD DISPLAY and CD FUNCTIONAL INDICATOR will light up. 2. Put a CD into the CD compartment with the label side upward. 3. Insert a cassette into the cassette compartment and press PAUSE BUTTON of the cassette deck. 4. Press RECORD BUTTON and PLAY BUTTON simultaneously for recording stand-by. With the built-in ALC, the best recording quality is adjusted automatically. 5. Activate the CD player, playing in a desired track as described in the COMPACT DISC PLAYER OPERATION section. Release the PAUSE BUTTON of the cassette deck to start recording. 6. To stop recording temporarily, press the PAUSE BUTTON. To continue recording, press the PAUSE BUTTON again. 7. Press STOP/EJECT BUTTON of the cassette deck to stop recording. Then stop CD playback by pressing the CD STOP BUTTON of the CD player. English - 10 AUXILIARY (AUX) MODE 1. Slide the FUNCTION SWITCH to the “AUX” position. 2. Connect the earphone socket from the Auxiliary unit (e.g. MP3 Player or MD Player) into AUX-IN-JACK (22) of this product via an Audio Line Cord (with 3.5mm plug on both ends ; Not supplied). 3. Play the Auxiliary unit. Music from the Auxiliary unit can be listened through the Speakers of this product. REMOTE CONTROL OPERATION Installing Batteries Slide open the BATTERY DOOR, install two “AA” size or UM-3 batteries according to the polarity diagram inside the battery compartment of the Remote Controller. Battery Replacement When batteries become weak, the operating distance of the Remote Controller is greatly reduced and you will need to replace batteries. Using The Remote Controller Correctly • Point the Remote Controller at the REMOTE SENSOR locates on the main unit. • The function of the button is the same as the corresponding control on the main unit. • When there is a strong ambient light source, the performance of the infrared REMOTE SENSOR may be degraded causing unreliable operation. • The recommended effective distance for remote operation is about 5 meters. 1. REMOTE SENSOR (40) 2. POWER BUTTON (41) a) While the main unit is in operation, press this POWER BUTTON (41) once, the unit will go to Standby Mode and POWER/STANDBY LED INDICATOR (16) will turn from green to red color. b) Press the POWER BUTTON (41) again and it will resume to normal play function. NOTE : When the POWER/STANDBY LED INDICATOR (16) is in red color, the unit is only in Standby Mode. Press the POWER BUTTON (1) locates on the main unit to turn off the unit completely. English - 11 3. STOP BUTTON (42) Press to stop CD play. 4. PLAY/PAUSE BUTTON (43) Press to start play or pause temporarily in CD Mode. 5. MODE BUTTON (44) Press in sequence for different play mode. Playing CD DISC : Repeat 1 Æ Repeat All Æ Random Play Æ Normal Play. Playing MP3 DISC : Repeat 1 Æ Repeat Folder Æ Repeat All Æ Random Play Æ Normal Play. 6. SKIP/SEARCH “-” (45) / “+” (46) Skip or Search backward / forward for the desired track or passage in CD mode. 7. FOLDER “-”(47)/ “+” (48) a) Press once to show the Folder number. b) Press twice to change the Folder number downward or upward. 8. VOLUME “-” (49) / “+” (50) Press to adjust the volume. 9. BATTERY DOOR (51) Slide open the battery door, then insert two “AA” size or UM-3 batteries according to the polarity diagram inside the battery compartment. Note : If the Remote Controller is not to be used for a long time, remove the batteries to prevent possible damage through battery. Do not mix different types of battery or old batteries with new ones. MAINTENANCE CLEANING THE TAPE HEADS Clean the heads frequently to remove dust and tape residue. Dirt on the heads will impair the sound quality of both recording and playback. English - 12 WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER, PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. English - 13
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021