CD800F
CAUTION
1. Correct measurement may not be performed when using the meter in a
ferromagnetic/intense electric field such as a place near a transformer,
high-current circuit or a radio.
2. The meter may malfunction or correct measurement may not be
performed when measuring a special waveform such as that from an
inverter circuit.
1-3 Overload protections
Function
Input terminals
ACV Hz
+ (Red)
and
- (Black)
DCV
CD800F
DIGITAL MULTIMETER
INSTRUCTION MANUAL
/
/
/
Max. rated input value
AC/DC 1100 V
DC 1000 V
Voltage input prohibited
+ or -
EF
Max. overload protection input
AC 1000 V
AC/DC 1000 V
AC/DC 1000 V
01-1611 2040 6006
4-4 Measurement function selection : SELECT button
• Safety design compliant to IEC61010.
• AC measurements with True RMS conversion.
• High portability thanks to the case-integrated design.
• Backlight.
• EF (Electric Field sensing).
Measurement categories (Overvoltage categories)
CAT. II : Primary circuit of equipment with a power cord to be connected to a
mains socket.
CAT. III : Primary circuit of equipment that inputs power directly from the
distributor and the circuit from the distributor to the mains socket.
CAT. IV : Circuit from the leading wire to the distributor.
[3] NAMES OF COMPONENT UNITS
The meaning of the symbols used in this manual and attached to the product is
as follows.
: Very important instructions for safe use.
• The WARNING messages are intended to prevent accidents to operating
personnel such as burn and electrical shock.
• The CAUTION messages are intended to prevent damage to the instrument.
Symbols attached to the product
: Symbol soliciting reference to this manual before use
: Double or enhanced insulation
: Ground
: Resistance
: Diode
: Buzzer
: Capacitance
: Backlight
3-1 Multimeter and test leads
Test pins
EF antenna position
Removable test pin covers
View when not attached
HOLD button
△ REL button
Finger guards
Display
Removable test pin covers
When covered: CAT.IV 1000 V
When uncovered: CAT.II 1000 V
SELECT button
RANGE button
Test probe (red)
Test probe (black)
Power/function switch
3-2 Display
Coverage
Note
0.000 - 3.000 V
Open voltage across input terminals: About 3.2 V
“OL” is displayed at 3.000 V or more.
Forward test
Cathode
Unit
: Voltage alarm
: Data Hold indicator
: Auto Range indicator
: Low battery indication
: Auto Power Save indicator
: Relative operation indicator
: Continuity check : Diode
: Capacitor
: Alternative Current : Direct Current : MAX/MIN mode indicator
3-3 Attaching the strap
Hand strap
Example of Good item:
Forward voltage
drop display
Example of NG item:
0.000 V display,
“OL” display
Example of Good item:
“OL” display
Example of NG item:
Other display
)
Coverage
Note
0.0 - 600.0 Ω
Open voltage across input terminals: About 1.0 V
The buzzer beeps at 10 to 50 Ω or less.
[6] MAINTENANCE
1. This section is very important for safety. Read and understand the
following instruction fully and maintain your instrument properly.
2. The instrument must be calibrated and inspected at least once a year to
maintain the safety and accuracy.
6-1 Maintenance and inspection
1) Appearance
• Is the appearance not damaged by falling?
2) Test leads
• Is the cord of the test leads not damaged or the core wire not exposed at
any place of the test leads?
If any of the above is found with the appearance, do not use the equipment
and have it repaired.
6-2 Calibration
The manufacturer may conduct the calibration and inspection. For more
information, please contact the dealers.
6-3 Cleaning and storage
CAUTION
)
Coverage
Range
0.00 - 600.0 μF
60.00 n/600.0 n/6.000 μ/60.00 μ/600.0 μ
Discharge the capacitor before
measurement.
It takes a while to measure large
capacitance.
This measurement is not suitable for
measurement of a capacitor with a
high leak current such as an
electrolytic capacitor.
1. The main unit is not resistant to volatile solvent and must not be cleaned
with lacquer thinner or alcohol. If it gets dirty, wipe lightly with a soft cloth
moistened with a small amount of water.
2. The main unit is not resistant to heat. Do not place it near a source of high heat.
3. Do not store the instrument in a place where it may be subjected to
excessive vibrations or from where it may fall.
4. For storing the instrument, avoid hot, cold or humid places or placed
under direct sunlight or where condensation is anticipated.
5. When the instrument is not to be used for a long period, be sure to
remove batteries from it.
6-4 Battery replacement
WARNING
1. If the rear case or the battery lid is removed with input applied to the input
terminals, you may get electrical shock. Before starting the work, always
make sure that no input is applied.
2. Before starting the work, be sure to turn OFF the main unit power and
release the test leads from the circuit.
5-5 EF (Electric Field) sensing
WARNING
1 This function identifies the presence of voltage in a simplified manner by
sensing the electric field generated by AC voltage.
Sensing voltage reference: A voltage or electric field of about 60 V or more
can be sensed.
2 When the function switch is set to EF, “EF” is displayed.
3 Antenna
• Noncontact type : An antenna is provided near the ▲ marking on the top
left of the main unit.
• Contact type: Bring the test pin of a test lead (either red or black) in contact
with the target.
More accurate sensing is possible by distinguishing the non-grounded and
grounded sides. “-” is displayed and the buzzer beep is generated on the
non-grounded (hot) side, while “EF” remains displayed and the buzzer beep
is not generated on the grounded side.
* “EF” may sometimes become “-” even on the grounded side. This happens
when the wiring is long, etc.
− 5 −
5-2 AC voltage measurement (ACV), frequency measurement (Hz)
Display
Coverage
Ranges
ACV
Hz
0.005 - 1000
10.00 - 99.99 k
6.000/60.00/600.0/1000 V
99.99/999.9/9.999 k/99.99 kHz
The accuracy-assured frequencies of the ACV measurement are 45 Hz to 500
Hz (sine wave AC).
Hz input sensitivity : 10.00 to 9.999 kHz: ≥1 Vrms. 10.00 kHz or more: ≥5 Vrms.
Set the function switch to ACV.
Each press of the SELECT button
alternates ACV and Hz.
appears on the display when a
voltage of 20 V or more is input.
At the moment the input exceeds 20 V,
the buzzer beeps and the backlight
flashes to indicate it.
When the △ REL button is held depressed, the meter enters the MAX/MIN
mode, in which the measurement range is fixed and the Auto Power Save and
Relative value measurement functions are canceled.
• Every time the SELECT button is pressed, the displayed information changes
as follows : Current measurement display (MAX MIN displayed) → MAX
value display (MAX displayed) → MIN value display (MIN displayed) →
Current measurement display (MAX MIN displayed) → …
• Current measurement display : The meter stores the maximum and minimum
values while displaying the current measurement value. The buzzer beeps
every time a value is updated. The maximum and minimum values can be
checked by pressing the button to view the MAX value display and MIN value
display. To cancel the MAX/MIN mode, press the button for 1 sec. or more.
• MAX value display : Maximum value measured since the entry in MAX/MIN
mode.
• MIN value display : Minimum value measured since the entry in MAX/MIN
mode.
The MAX/MIN mode can also be entered when the relative value measurement
function is active ( △ displayed). In this case, the MAX/MIN mode displays the
relative values assuming that the value at the moment the button is pressed is 0
(reference value).
MAX/MIN memory mode is not available in the Hz, , , and EF functions.
* The MAX/MIN mode is canceled when the function or range is switched.
When the HOLD button is pressed, the current display is hold (
appears
on the display).The display will not be changed even when the input varies
on the
thereafter. Press the button again to cancel the Data Hold mode (
display disappears). This function is not available in the EF function.
* The Data Hold mode is also canceled when the function switch is switched or
the RANGE or SELECT button is pressed.
5-3 DC voltage measurement (DCV)
Display
Coverage
Ranges
DCV
0.0 m - 1000
600.0 m/6.000/60.00/600.0/1000 V
Set the function switch to DCV.
appears on the display when a
voltage of 20 V or more is input.
At the moment the input exceeds 20 V,
the buzzer beeps and the backlight
flashes to indicate it.
5-4 Resistance ( ), diode (
), continuity (
) , capacitance (
)
WARNING
• Never apply voltage to the input terminals.
Set the function switch to
Each press of the SELECT button switches the function in order of
→
→ …
5-4-1 Resistance measurement (
Display
→
→
)
Coverage
Ranges
0.0 - 60.00 MΩ
600.0/6.000 k/60.00 k/600.0 k/6.000 M/60.00 MΩ
The open voltage across the measurement terminals is about DC 1.2 V.
4-10 Disable Buzzer
If measurement is likely to be influenced
by noise, shield the object to measure
with negative potential (COM). If a finger
touches a test pin during measurement,
measurement will be influenced by the
resistance in the human body, and that
results in measurement error.
Resistor
When the meter is switched on while holding the △ REL button displayed, the
for 2 seconds and the buzzer beep is canceled. Even when
display shows
the buzzer is canceled, it still beeps in the case of OL alarm, in the continuity
check, when the meter is turned on and before Auto Power Save. To enable all
of the buzzer sounds, turn the meter off then on again.
* This mode cannot be used when the Auto Power Save function is canceled.
7-2 Repair
− 4 −
8-2 Optional accessory
Customers are asked to provide the following information when requesting
services:
1. Customer name, address, and contact information
2. Description of problem
3. Description of product configuration
4. Model Number
5. Product Serial Number
6. Proof of Date-of-Purchase
7. Where you purchased the product
Please contact Sanwa authorized agent / distributor / service provider, listed in
our website, in your country with above information. An instrument sent to
Sanwa / agent / distributor without those information will be returned to the
customer.
Note:
1) Prior to requesting repair, please check the following:
• Capacity of the built-in batteries and polarity of installation.
• Discontinuity of the test leads.
2) Repair during the warranty period:
The failed meter will be repaired in accordance with the conditions stipulated
in 7-1, Warranty and provision.
3) Repair after the warranty period has expired:
• When the original functionality is expected to be restored by repair, we will
repair the product upon request and payment by the customer.
• In some cases, repair and transportation cost may become higher than the
price of the product. Please contact Sanwa authorized agent/service provider
in advance.
• The minimum retention period of service functional parts is six (6) years after
the discontinuation of manufacture. This retention period is the repair
warranty period. Please note, however, if such functional parts become
unavailable for reasons of discontinuation of manufacture, etc., the retention
period may become shorter accordingly.
4) Precautions when sending the product to be repaired
• To ensure the safety of the product during transportation, place the product in
a box that is larger than the product 5 times or more in volume and fill
cushion materials fully.
• Clearly mark “Repair Product Enclosed” on the box surface.
• The cost of sending and returning the product shall be borne by the customer.
Hanger magnet: HM-1
8-3 Measurement ranges and accuracies
Accuracy-assured temperature/humidity ranges: 23±5 ºC, ≤ 80 %RH, no
condensation.
rdg: reading.
dgt: digits (lowest digits)
As the ACV measurements employ the rms value response, the accuracyassured ranges and crest factor become as follows.
Accuracy range: 1 % to 100 % of measurement range.
Crest factor CF: Full scale CF < 1.8, half scale CF < 3.6.
Function
AC voltage
ACV
1 Using a Phillips screwdriver, turn
the battery lid retaining screw
(x1) until it becomes loose.
2 Press the position marked
PUSH to lift the battery lid, and
then remove it.
3 Replace the batteries by taking
care of the polarity.
4 Attach the battery lid and
tighten the retaining screw.
[7] AFTER-SALE SERVICE
7-1 Warranty and provision
Sanwa offers comprehensive warranty services to its end-users and to its
product resellers. Under Sanwa's general warranty policy, each instrument is
warranted to be free from defects in workmanship or material under normal use
for the period of one (1) year from the date of purchase.
This warranty policy is valid within the country of purchase only, and applied
only to the product purchased from Sanwa authorized agent or distributor.
Sanwa reserves the right to inspect all warranty claims to determine the extent
to which the warranty policy shall apply. This warranty shall not apply to
disposables batteries or any product or parts which have been subject to one of
the following causes:
1. A failure due to improper handling or use that deviates from the instruction
manual.
2. A failure due to inadequate repair or modification by people other than Sanwa
service personnel.
3. A failure due to causes not attributable to this product such as fire, flood and
other natural disaster.
4. Non-operation due to a discharged battery.
5. A failure or damage due to transportation, relocation or dropping after the
purchase.
− 6 −
60.00 V
600.0 V
Frequency
Hz
DC voltage
DCV
△ - Σ method
AC detection method
True RMS method (AC coupling)
Display
Max. 6000 counts
Sampling rate
Max. approx. 5 times/sec.
Overload indication
“ OL” mark indication on digital display
Range selection
Auto and Manual
Polarity switching
Auto (“-” indicated when negative voltage is input)
99.99 kHz
600.0 mV
Input resistance: About 10 MΩ
9.999 kHz
6.000 V
60.00 V
mark displayed when battery voltage drops at 2.3 V or less.
Altitude ≤2000 m, indoor use, pollution degree II
Operating temperature/
humidity ranges
-10 ºC to 40 ºC.
Humidity range is as follows (without condensation):
Max. 80 %RH at 5 ºC to 31 ºC, decreasing linearly to 50 %RH at
40 ºC.
Storage temperature/
humidity range
-20 ºC to 40 ºC: ≤80 %RH (without condensation).
40 ºC to 50 ºC: ≤70 %RH (without condensation).
(Batteries should be removed when the instrument is not to be
used for a long period.)
Temperature coefficient
Below 18 ºC and above 28 ºC: Accuracy x 0.15 should be added
function.)
per ºC. (Accuracy x 0.25 should be added in the
Power supply
LR03 (“AAA”-size alkaline battery)1.5 V × 2
Auto Power Save
Power Save in about 15 minutes after last operation. Typ. 20 µA
Current drain
About 1.5 mA (backlight off). max. about 38 mA
Battery life
About 600 hours (backlight off)
Dimensions & mass
166 (H) x 100 (W) x 43 (D) mm, about 360 grams (incl. batteries)
Test lead length
About 0.8 m
Safety standards
IEC61010-1, IEC61010-2-030, IEC61010-2-33, IEC61010-31
CAT.IV 1000 V
EMC Directive, RoHS
Directive
IEC61326 (EMC), EN50581 (RoHS)
Accessories
Instruction manual, “AAA”-size alkaline battery x 2, hand strap
− 7 −
± (0.5 %rdg+3 dgt)
± (0.8 %rdg+3 dgt )
600.0 V
1000 V
6.000 kΩ
Resistance
60.00 kΩ
± (1.1 %rdg+5 dgt)
± (1.2 %rdg+5 dgt)
600.0 kΩ
6.000 MΩ
± (2.0 %rdg+5 dgt)
60.00 MΩ
± (4.0 %rdg+5 dgt)
• Open voltage: About DC 1.8 V
• Measurement current varies
depending on the resistance
value of the object measured.
Diode test
Open voltage: About DC 3.2 V
“OL” displayed at 3.000 V or more.
Continuity check
Open voltage: About DC 1.0 V
Buzzer beep generated at 10 to
50 Ω or less.
600.0 nF
± (3.0 %rdg+10 dgt)
6.000 μF
60.00 μF
Operating environmental
conditions
± (1.5 %rdg+7 dgt)
600.0 Ω
Capacitance
Operation method
± (1.2 %rdg+5 dgt)
Remarks
Input resistance: About 10 MΩ
• Accuracy-assured
frequencies: 45 Hz – 500 Hz
Input resistance: About 10 MΩ
• Accuracy not assured below
10 Hz.
• Sensitivity 10 Hz: ≥ 1 Vrms
10 kHz: ≥5 Vrms
999.9 Hz
60.00 nF
8-1 General specifications
Low battery indication
Accuracy
± (1.2 %rdg+9 dgt)
1000 V
7-3 SANWA web site
http://www.sanwa-meter.co.jp
E-mail: [email protected]
Range
6.000 V
99.99 Hz
[8] SPECIFICATIONS
Batteries
1. Before EF sensing, check the operation of this instrument using a known
power source.
2. Always keep your fingers behind the finger guards on the probe when
making EF sensing.
3. Note that the voltage is not always absent and that a voltage below the
sensing voltage may exist.
Check the following items before starting the daily measurement work.
• Appearance check : Check the appearance of the meter to see if it is free
from damage caused by falling, etc.
• Accessory : Check that the test leads are free from irregularities such as
wire disconnection and crack.
• Battery: Install the battery before using the meter for the first time. Ensure
low battery indication is not displayed and, if it is displayed,
that the
replace the battery with new one. If nothing is displayed, the battery may be
exhausted totally (see 6-4).
• Test lead wire disconnection can be checked by setting the function switch
to and shorting the test pins.
• Also check that the meter and your hands are not moistened by water, etc.
− 3 −
Note: Because of the high
sensitivity, the EF sensing
may be activated at a
distance of some tens of
centimeter apart from a
source of high frequencies
such as an inverter circuit.
Reverse test
Anode
5-1 Start-up inspection
Insert the Hand strap into the strap hole as
shown in the figure.
WARNING
display
Press the RANGE button momentary to set the manual range mode (AUTO
disappears in the display). In manual range mode, press the button again to step
through the ranges. To return to the auto mode, press and hold the button for 1
sec. or more (then ‘AUTO’ is shown).
Manual range hold mode is not available in the Hz, , , and EF functions.
4-9 Data Hold : HOLD button
)
5-4-4 Capacitance measurement (
4-6 Range Hold : RANGE button
− 2 −
Diode
Display
When the SELECT button is held depressed (for more than 2 sec.), the backlight
of the LCD turns on. Holding the same button depressed again turns it off. The
backlight also turns of automatically in about 30 seconds.
4-8 MAX/MIN memory : △ REL (MAX/MIN) button
Strap hole
− 1 −
5-4-3 Continuity check (
4-5 Backlight : SELECT ( ) button
WARNING
1. Never apply an input signal exceeding the maximum rating input value of
each function.
2. Be sure to disconnect the test pins from the circuit when changing the function.
3. Always keep your fingers behind the finger guards on the probe when
making measurements.
4. After measurement, release the red and black test pins from the object
measured and set the function switch to the OFF position.
When the △ REL button is pressed, △ appears on the display, the measuring
range is fixed and the display shows the relative values assuming that the value
at the moment the button is pressed is 0 (reference value). When the button is
pressed again, △ disappears and the relative value measurement is canceled.
Relative value measurement mode is not available in the Hz,
, and EF
functions.
1-1 Explanation of Warning Symbols
When the SELECT button is pressed, the functions change as follows.
ACV position : ACV → Hz → ACV → …
position : →
→
→
→ →…
[5] MEASUREMENT PROCEDURE
4-7 Relative value measurement : △ REL button
together with the product for reference to it when necessary.
If you use the product in a method not specified in this manual, the protection
function of the product may be imperiled.
The instruction given under the heading of “
WARNING” and “
CAUTION” must
be followed to prevent accidental burn or electrical shock.
Display
The Auto Power Save function turns the display off automatically in about 15
minutes after the last operation or after an input of 20 V or higher was applied to
save the power consumption. To return from this status, press the SELECT or
RANGE button or turn the power switch to OFF then to another position.
To disable the Auto Power Save function, switch the meter on by turning the
function switch while holding the SELECT button depressed. A short buzzer
beep is generated, “
” is displayed for 2 seconds, and the indicator
disappears.
* A small current flows inside the meter even in the Auto Power Save status.
After measurement, always turn the function switch to the OFF position.
This instrument is a digital multimeter with rms value response, designed for
measurements within the range specified as CAT.IV 1000 V in IEC61010.
This instruction manual explains how to use your new digital multimeter CD800F
safely. Before use, please read this manual thoroughly. After reading it, keep it
5-4-2 Diode test (
4-2 Auto Power Save
2-1 Applications
Before use, read the following safety precautions.
WARNING
The following instructions are intended to prevent personal injury such as
burn and electric shock. Be sure to follow them when using the tester.
1. This instrument is a digital multimeter for metering low voltages. Never
use it on electric circuits that exceed CAT.IV 1000 V.
2. Pay special attention when measuring the voltage of AC 33 Vrms (46.7 V
peak) or DC 70 V or more to avoid injury.
3. Never apply an input signal exceeding the maximum rating input value (see 1-3).
4. Never use the meter for measuring the line connected with equipment (i.e.
motors) that generates induced or surge voltage since it may exceed the
maximum allowable voltage.
5. Never use meter if the meter or test leads are damaged or broken.
6. Never use uncased meter or the meter without the lid.
7. Always keep your fingers behind the finger guards on the probe when
making measurements.
8. Be sure to disconnect the test pins from the circuit when changing the function.
9. Before starting measurement, make sure that the function and range are
properly set in accordance with the measurement.
10.Never use meter with wet hands or in a damp environment.
11.Never open tester case except when replacing batteries.
Do not attempt any alteration of original specifications.
12.To ensure safety and maintain accuracy, check the meter in the start-up
inspection as well as in the inspection/calibration to be performed at least
once a year.
13.The meter is for indoor use only.
14.Wear insulating protective gear when using the meter with equipment
containing a hazardous live part. Also be sure to observe your local and
national safety rules.
15. Always use the meter in a specified method to prevent the protective
function from being imperiled.
Turn this switch to turn on and off the power and to switch the measuring
functions.
When the batteries are exhausted until the supply voltage drops below about
2.3 V, the
indicator lights on the display. Replace the batteries when this
indicator appears.
[1] SAFETY PRECAUTIONS
1-2 Warning Instructions for Safe Use
4-1 Power/Function switch
4-3 Low battery indication
[2] APPLICATIONS AND FEATURES
2-2 Features
Dempa Bldg., 4-4 Sotokanda 2-Chome
Chiyoda-ku, Tokyo 101-0021, Japan
[4] DESCRIPTION OF FUNCTIONS
± (5.0 %rdg+10 dgt)
600.0 μF
Electric field
sensing
EF
Auto range only.
Accuracy with a capacitor with
low leak current such as a film
capacitor or equivalent.
Less than 10 nF add +15 dgt to
the accuracy.
At the standard sensing voltage of
Sensing frequencies: 50/60 Hz.
about 60 V or more, the bar graph and Sensing antenna: Near ▲ on top
intermittent sound vary in 5 steps.
left of main unit.
Contact type EF sensing : Test pin
Accuracy calculation method
Example) AC voltage measurement (ACV)
Displayed value: 100.0 V
Range accuracy: 600.0 V range ±(1.2 %rdg + 5 dgt)
Error: ±(100.0 V x 1.2 %rdg + 5 dgt) = ±1.7 V
True value: 100.0 V ±1.7 V (between 98.3 - 101.7 V )
* In the 600.0 V range, 5 dgt corresponds to 0.5 V.
Specifications and external appearance of the product described
above may be revised for modification without prior notice.
− 8 −
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement