User manual Bedienungsanleitung Manuel d'Utilisateur Manuale

User manual Bedienungsanleitung Manuel d'Utilisateur Manuale
Picture similar
Digital Terrestrial HD Receiver PRIMA VI
User manual
Bedienungsanleitung
Manuel d’Utilisateur
Manuale Utente
Manual del usuario
Manual do Utilizador
Felhasználói kézikönyv
Instrukcja obsługi
Ръководство на потребителя
Table of Contents
27 May 2013 15:03
1.0 Introduction
1.1 Safety Instructions
1.2 Storage
1.3 Equipment Set-up
1.4 Accessories
1.5 Usage of external USB devices
2.0 Your Receiver
2.1 DEFAULT PIN: 1234
2.2 Front Panel
2.3 Rear Panel
2.4 Remote Control
3.0 Connection
3.1 Connecting to a Terrestrial Antenna
3.2 Connecting to TV with HDMI cable
3.3 Connecting to TV with SCART cable
3.4 Connecting to a Digital Audio Amplifier with S / PDIF
3.5 Connecting to a Digital Audio Amplifier and TV using HDMI
3.6 Connecting to an analogue Audio Amplifier
3.7 Connecting a USB storage device
4.0 Starting up for the first time
5.0 Quick guide to using your receiver
6.0 Operation
6.1 Changing channels
6.2 Info Banner
6.3 Selection of audio language
6.4 Teletext
6.5 Subtitles
6.6 Timeshift
6.7 EPG (Electronic Programme Guide)
6.8 Instant Recording
7.0 Main Menu
7.1 Edit Channel
7.2 Installation
7.3 System Setup
7.4 Tools
7.5 Games
7.6 Media
8.0 Troubleshooting
9.0 Technical Specifications
2
2
2
3
3
3
4
4
4
4
4
5
5
5
5
5
6
6
6
6
7
7
7
8
8
8
8
9
9
9
9
9
12
12
15
16
16
18
20
STRONG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHS
2002/95/EC
Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may
change. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries, Dolby and the double-D symbol are registered trademarks of Dolby Laboratories. All other product names are trademarks or
registered trademarks of their respective owners.
© STRONG 2013. All rights reserved.
1
English
PART 1 • English
PART 1 • English
1.0 Introduction
1.1 Safety Instructions
DO NOT INSTALL YOUR RECEIVER:
In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface
which might obstruct the ventilation slots.
DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES:
„„To direct sunlight or any other equipment that generates heat; to rain or intense
moisture; to intense vibration and to any shock which may cause permanent damage
to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc.
„„Do not use a damaged power cord. It may cause a fire or an electric shock. Do not
touch a power cord with wet hands. It may cause an electric shock.
„„When the receiver is not used for a long period of time, you should unplug the power
cord from the wall socket.
„„Do not use alcohol or ammonia based liquids to clean the receiver. If you wish, you
may clean your receiver with a soft lint-free cloth slightly made damp with a mild soap
solution, and only after disconnecting from the mains voltage supply. Make sure no
foreign objects fall through the ventilation slots because this could cause fire or an
electric shock.
„„Do not place any objects on top of the receiver because this might prevent proper
cooling of the components inside.
Safety Precautions
„„Never try to open the receiver. It is dangerous to touch the inside of the receiver
due to high voltages and possible electrical hazards. Opening the receiver will
void the warranty of the product. Refer all maintenance or servicing to suitably
qualified personnel.
„„When you are connecting cables, be sure that the receiver is disconnected from the
mains supply voltage. Wait a few seconds after switching off the receiver before you
move the receiver or disconnect any equipment.
„„It is a necessity that you only use an approved extension and compatible wiring that
is suitable for the electrical power consumption of the installed equipment. Please
ensure that the electrical power supply corresponds with the voltage on the electrical
identification plate at the back of the receiver.
If the receiver does not operate normally even after strictly following the instructions in this user
manual, it is recommended to consult your dealer.
1.2 Storage
Your receiver and its accessories are stored and delivered in a packaging designed to protect against
electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep
the packaging away from children. When transporting the receiver from one place to another or if you
are returning it under warranty conditions, make sure to repack the receiver in its original packaging
2
PART 1 • English
English
with its accessories. Failing to comply with such packaging procedures could damage the product
and void your warranty.
1.3 Equipment Set-up
We recommend you consult a professional installer to set up your equipment. Otherwise, please
follow the instructions below:
„„Refer to the user manual of your TV and antenna.
„„Make sure that the HDMI cable and outdoor components are in a good condition.
„„Use only a HDMI 1.3 cable or higher for maximum performance.
„„If you use TV SCART connection, use then well shielded SCART cable.
This manual provides complete instructions for installing and using this receiver. The following
symbols will serve as follow.
WarningIndicates warning information.
TipsIndicates any other additional important or helpful information.
MENURepresents a button on the remote control or the receiver. (Bold Character)
Move toRepresents a menu item within a window. (Italic Character)
1.4 Accessories
„„User manual
„„1 remote control unit
„„2x batteries (AAA type)
The batteries should not be recharged, disassembled, electrically short-circuited, be mixed or used
with other types of batteries. If rechargeable accumulators instead of batteries are going to be used
(e.g. NiMH), we recommend using types with low self-discharge to ensure long time operation of
your remote control.
1.5 Usage of external USB devices
„„It is recommended to use USB 2.0 storage devices or higher. If your device is not
compatible to USB 2.0 specifications, recording, playback and other multimedia
functions of the receiver might not work properly.
„„To ensure best performance of your USB storage device please format it via your
receiver (through the menu “Media”) to FAT32 system. Other file systems are not
supported by the receiver. However, it is possible to use already NTFS formatted disks.
„„STRONG cannot guarantee compatibility with all types of USB storage devices.
„„If you are going to use external USB HDDs (Hard Disk Drives), please consider that
power specifications may exceed the supported output of your receiver (max.5 V/800
mA). If so, please connect your USB HDD to an according external power adapter.
„„It is advised not to store important information on USB storage devices used with
the receiver. Always make backups of data on your USB storage device before using it
with this receiver. STRONG will not take responsibility for any loss of information or
circumstances caused by loss of information.
3
PART 1 • English
2.0 Your Receiver
2.1 DEFAULT PIN: 1234
2.2 Front Panel
Fig. 1
1. USBConnector for USB storage devices.
2. IR sensorPoint your remote control towards this sensor.
3. Mode indicatorRED indicates that the receiver is in STANDBY mode.
GREEN indicates that the receiver is in OPERATING mode.
4. Standby/On buttonSwitch the receiver ON to running mode or STANDBY mode
2.3 Rear Panel
Fig. 2
1. ANT INTo connect to your antenna for reception of broadcasted signals.
2. ANT OUTTo connect the terrestrial antenna signal to your TV set.
This connection will allow you to watch digital terrestrial
programmes depending on the tuner of your TV and local
broadcast conditions.
3. S / PDIF CoaxialTo connect your receiver to a digital home theatre, AV receiver or
digital audio amplifier.
4. HDMITo connect your receiver with your TV set using an HDMI cable.
5. TV SCARTTo connect your receiver with your TV set using a SCART cable.
6. Audio R/L outTo connect your receiver to an analogue audio amplifier.
7. Power CordYour receiver requires a supply voltage of 220~240 V AC
(Auto-selectable), 50/60 Hz ±5%. Please ensure the local power
specification meets these requirements before connecting your
receiver to the wall outlet.
2.4 Remote Control
Fig. 3
qSwitches the receiver On/Standby
!Mutes all audio outputs of the receiver
PG+/PG-Page up/down in all list modes
DTV/VCRNo function
INFOOpens the current channel information; 2x opens the current
event information and 3x the signal information
6. VOL+/VOL-Increases/decreases the volume level
7. MENUOpens the main menu, in a menu you will get one step back
8. EXITExits from the menu or sub-menu
9. pq
Menu Off: Change channel to previous/next.
Menu On: Moves the cursor up/down.
10.tuMenu Off: Increases/decreases the volume level.
Menu On: Change settings for specific menus
1.
2.
3.
4.
5.
4
11.OKMenu Off: Displays the current channel list
Menu On: Activates the highlighted menu item.
12.RECORDRecords the TV programme to the connected USB storage device
13.TIMESHIFTActivates the Timeshift function (Off/On)
14.0~9Enters a channel number in viewing mode or a value inside the
respective menu
15.EPGOpens the EPG (Electronic Programme Guide) in TV mode
16.RECALLBack to previously watched channel
17.AUDIOOpens the audio language selection
18.TV/RADIOToggles between TV or RADIO mode
19.FAVOpens the favourite group selection
20.FILEOpens the Media Player list
21.TTXDisplays Teletext on the OSD (On Screen Display)
22.SUBTITLEShows a list of subtitle languages
23.5 6Fast rewind/fast forward
24.Coloured buttonsFor Multimedia and Teletext functions
3.0 Connection
3.1 Connecting to a Terrestrial Antenna
Fig. 4
To receive broadcasted signals, your terrestrial indoor or outdoor antenna must be connected
to the ANT IN connector on the back of the receiver. Use a properly shielded antenna cable and
suitable connectors.
The ANT OUT connector allows you to loop the antenna signal to a second receiver or TV set.
Please consider that the looped signal might be too weak if you use an active antenna.
If the signals at your location are too weak to receive proper signals with an indoor antenna, we
recommend using an outdoor antenna which can be pointed towards the transmission tower. Ask
your local dealer for more information.
3.2 Connecting to TV with HDMI cable
Fig. 4
The TV set shall be connected with the receiver using a good quality HDMI 1.3 or higher cable. This
connection gives the highest possible quality.
3.3 Connecting to TV with SCART cable
Fig. 4
Your receiver is also equipped with a SCART connector; alternatively, the TV set can be connected to
the receiver using a good quality SCART cable.
3.4 Connecting to a Digital Audio Amplifier with S / PDIF
Fig. 4
By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best
possible sound quality and multi-channel audio (depending on broadcast). Connect your Digital
5
English
PART 1 • English
PART 1 • English
Audio Amplifier or home theatre system with a suitable cinch cable to the S / PDIF connector on the
back of the receiver.
3.5 Connecting to a Digital Audio Amplifier and TV
using HDMI
Fig. 5
By connecting your receiver to the latest digital amplifiers or Home Cinema systems, preferable
with HDMI 1.3 connections, you will enjoy the best possible sound quality and multi-channel audio
(depending on broadcast). Connect the HDMI output of the receiver to an input of your amplifier,
and then connect the HDMI output of the amplifier to your TV set. Select the correct input on your
amplifier to watch and listen to programmes.
3.6 Connecting to an analogue Audio Amplifier
Fig. 5
Use the 3.5 mm jack to connect your receiver to the analogue input of your Hi-Fi or audio amplifier
with an RCA cable for achieving best possible analogue audio quality.
3.7 Connecting a USB storage device
Fig. 6
It is recommended to use USB 2.0 storage devices or higher for recording and play back of TV
programmes or HD movies.
Timeshift/recording and playback only works properly when a fast USB storage device such as a
USB2.0 HDD is connected to the receiver. Timeshift/recording and playback of HD content requires a
sufficient read/write speed of the used USB storage device.
4.0 Starting up for the first time
When you use your receiver for the first time, the Welcome “Easy install” menu appears. Use pq to
move the highlight to the setting you wish to alter and use tu to change values. Start by selecting
your language using tu. Once you have selected your language, press q to move the highlight to
the next item and use tu to change.
LanguageHere you can choose your language.
Region:
Select your region where this receiver is used.
Subtitle:
Select Normal to display subtitles per default, Select Hard of Hearing to show
HoH subtitles per default. Select Off to hide subtitles per default.*
Aspect Mode:
Use this option to select the aspect ratio of your TV and the preferred
conversion method. Options are:
Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 16:9
widescreen broadcasts full screen on your 4:3 TV), 4:3 letterbox (black bars
on top and under the picture on a 4:3 TV) and 16:9 (use this setting for 16:9
TV sets).
Scan mode:
Select All to store scrambled and free to air channels or select Free to store
only free to air channels.
Note:Scrambled channels cannot be viewed with this receiver.
6
Connection:
se this option to adjust the established connection to your TV set. Select
U
HDMI or TV SCART.
* Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext
if available.
When all settings have been made, move the highlight to OK and press OK to continue.
Wrong region selection can lead to missing channels or channels being stored at wrong positions in
the channel list.
The receiver will now advance to the Aerial Adjustment screen.
This part of the wizard is of great help when setting up your antenna system.
Use pq to move the highlight to the setting you wish to alter and use tu to change values. The
following settings are available:
Antenna Power:
Set to On if you use an active antenna. When set to On, 5 V will be present at
the ANT IN connector of the receiver. Select Off for passive antennas.
Beeper:
Select On for an audible indication of signal reception. Off turns the
beeper off.
Channel No.:
Select a channel that is known to carry a broadcast in your region. The Signal
Strength and Signal Quality bars give a visual indication of the reception.
Adjust your antenna to obtain maximum signal strength and quality.
When all settings have been made, press OK to start scanning.
The receiver will search for all available channels now. Once scanning is finished, the receiver switches
to viewing mode.
If the Welcome menu does not appear after switching on the receiver the first time, reset the receiver
to factory settings by pressing the MENU button and selecting Load Factory Setting in the submenu
Tools. (DEFAULT PIN: 1234).
5.0 Quick guide to using your receiver
We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial
receiver. The following quick guide will make you familiar with the basic operation of this device. We
do, however, advice you to read the full manual to get the best performance from your receiver.
To turn your receiver ON or to Standby, press the q button on the remote control or on the front
panel.
Choose the desired channel with the pq buttons. Alternatively, you can digit the channel number
with the 0~9 buttons on the remote control or press OK in viewing mode to display the channel list.
The volume can be adjusted with the tu buttons.
6.0 Operation
Your new receiver is equipped with several features to make watching TV a true pleasure. This
paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of
your receiver.
6.1 Changing channels
Following ways are possible for changing channels with your new receiver:
„„Via direct access using the 0~9 buttons.
„„Via the channel list through OK and the PG+/PG- buttons.
„„Via the pq buttons.
7
English
PART 1 • English
PART 1 • English
6.1.1 Direct access via 0~9 buttons
To gain direct access to a certain channel, simply input its number with the 0~9 buttons on the
remote control. Channel numbers can be up to four digits long. Entering a number with less than
four digits is possible. Just wait a few seconds and your receiver will switch to the selected channel or
press OK immediately after selecting the channel number.
6.1.2 Channel list
Press OK in viewing mode to display the Channel List. Use pq in the channel list to highlight your
channel of choice and press OK once to select the highlighted channel. Press OK again to leave the
channel list mode. Inside the channel list it is possible to use the PG+/PG- buttons as well in order to
scroll page-wise through the list.
Use tu to toggle between the All Channel list and favourite list(s) or press FAV in viewing mode for
a list of available favourite lists.
6.1.3 Using the pq buttons
p switches to the next channel.
q switches to the previous channel.
6.2 Info Banner
While watching TV you can press the INFO button at any time to access current information about
the channel and event*. Press INFO twice for extended EPG details about the current channel. Press
INFO three times for technical details about the current channel.
Event information is displayed when available. Availability depends on broadcast.
6.3 Selection of audio language
Some channels support a choice of audio formats and/or languages. To select another audio stream,
press AUDIO in viewing mode. A list with available audio streams will now be displayed. Use pq to
select the desired stream and confirm with OK. The audio channel as stereo, mono, left and right can
be selected with the tu buttons.
6.4 Teletext
Your receiver includes a fully featured Teletext. To access Teletext, press the TTX button in viewing
mode and use the 0~9 buttons to input the number of the page you wish to see. The coloured
buttons of the remote control allow you to jump to selected pages directly, as indicated on the bottom
of the Teletext screen. Use the pq buttons to select one page up or down, press the tu buttons to
select subpages. Press EXIT or TTX to get back to viewing mode.
6.5 Subtitles
Some channels support a choice of subtitle languages. Press SUBTITLE in viewing mode to display a
list of available subtitle languages. Select your subtitle of choice with pq and press OK to confirm.
Press EXIT to leave without making changes.*
* Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext
if available.
8
PART 1 • English
Timeshift allows you to pause live broadcasts and resume playback later. Press TIMESHIFT in viewing
mode to activate this mode. On screen the message Timeshift On appears, live TV keeps playing. To
pause press the 2 button and press u to resume Timeshifted playback. Press 5 6 for fast rewind/
fast forward. Press 3 to return to live TV. Press TIMESHIFT to exit the Timeshift mode.
Timeshift and its playback only work properly when a fast USB storage device such as a USB2.0 HDD
is connected to the receiver. Timeshift and playback of HD content requires sufficient read/write
speed of the used USB storage device.
6.7 EPG (Electronic Programme Guide)
The Electronic Programme Guide is a very useful function that allows you to view event schedules
and programme information and to mark events/movies for recording. To access the EPG, press the
EPG button in viewing mode. Use pq to select a channel and tu to select an event. Press OK to
display detailed information of the selected event. Use EXIT to quit the detailed information screen.
Press RED to access further step functions. Use tu to select the desired step and OK to execute it.
Press EXIT to quit the step function. Press GREEN to set a timer for a selected event. Refer to section
7.3.4 for details of the timer function.
Availability of EPG data depends on broadcast.
6.8 Instant Recording
Your new receiver allows you to make an instant recording of the programme you are watching.
Simply press RECORD to start the recording. To enter the duration for the recording, press RECORD
again. Use the 0~9 buttons to enter the recording time.
At the begin of the recording a recording sign will be shown for a short while on the upper left
corner of your TV screen. To stop the recording, press 3. Select Yes and press OK again to stop
the recording.
You can access the Record Manager via the FILE button, and select Record by pressing the button 1.
See chapter 7.6.1 for details.
*Please connect a USB storage device with sufficient free space before you start a recording.
7.0 Main Menu
The main menu gives you access to settings, multimedia functions and games. To access the main
menu, press MENU in viewing mode. The main menu consists of the following sub menus: Edit
Channel, Installation, System Setup, Tools, Game and Media.
Throughout the main menu, MENU or EXIT can be used to get back to the previous screen.
7.1 Edit Channel
Use pq to select Edit Channel and press OK or u to enter.
Use pq to highlight the submenu of choice and press OK to select.
Press EXIT or t to get back to the main menu.
7.1.1 TV Channel List
In Edit Channel menu select TV Channel List with pq and press OK to enter.
Use tu to change the channel group (assumed you have already set up favourite groups).
Select the channel of choice with pq. Press OK to view the selected channel in the preview box.
9
English
6.6 Timeshift
PART 1 • English
7.1.1.1 Adding channels to favourite lists
Channels from the TV Channel List can be added to up to 8 different favourite groups. Press FAV in
TV Channel List to access this function. The FAV sign on the top of the screen will move up to indicate
that the favourite function is selected. Use pq to select a channel you wish to add to a favourite
group. When the highlight is on the channel of your choice, press OK. A list with all available favourite
lists will now pop up. Use pq to select the favourite list you wish to add the channel to and press
OK, press EXIT to finalize the process. Favourite channels will be marked with a heart symbol. When
all changes have been made, press EXIT twice. A confirmation banner will pop up. Select Yes to save
the changes or No to discard.
7.1.1.2 Locking channels
Locked channels can only be watched after entering the PIN code. (DEFAULT PIN: 1234)
To lock or unlock a channel, press RED while in TV Channel List. The red Lock sign on the top of the
screen will move up to indicate that the Lock function is selected. Use pq to select the a channel
and press OK to lock or unlock it. You are asked to input the PIN code. (DEFAULT PIN: 1234 Locked
channels will be marked with the  symbol. Locking/unlocking multiple channels in one session is
possible. When all changes have been made, press EXIT twice. A confirmation banner will pop up.
Select Yes to save the changes or No to discard.
7.1.1.3 Skipping channels
Channels marked with Skip will be skipped when zapping channels with the pq buttons. The
channels will still be available from the channel list.
To mark channels for skipping, press GREEN while in TV Channel List. The Skip symbol on the top
of the screen will move up to indicate that the Skip function is selected. Use pq to select a channel
and press OK to mark or unmark it for skipping. Channels set for skipping will be marked with the
 symbol. When all changes have been made, press EXIT twice. A confirmation banner will pop up.
Select Yes to save the changes or No to discard.
7.1.1.4 Moving channels
To enable the Move function, press YELLOW while in TV Channel List. The Move symbol on the top of
the screen will move up to indicate that the Move function is selected. Use pq to select a channel
and press OK to select it. Now you can move the selected channel up or down inside the channel list
by using pq. When the channel is on the position of your choice, press OK again. The channel is
now fixed on its new position. When all changes have been made, press EXIT twice. A confirmation
banner will pop up. Select Yes to save the changes or No to discard.
7.1.1.5 Editing channels
The Edit function allows you to Sort, Rename or Delete channels. To enter the Edit menu, press BLUE
while in TV Channel List. The Edit Channel menu will appear.
If you made changes in the previous menu, but haven’t saved them yet, you will be asked to do
so now.
Sort
Press RED to enter the Sort menu.
Use pq to select sorting method and press OK to confirm.
10
PART 1 • English
orting in alphabetical order from A to Z.
S
Sorting in alphabetical order from Z to A.
First in the list will be Free-To-Air channels.
All unlocked channels will placed first in the list.
Sorting by searched Order (from lowest to highest frequency or by LCN
numbering).
English
Possible methods are:
Name (A-Z):
Name (Z-A):
Free/Scramble:
Lock:
Default:
Rename
Press GREEN in Edit Channel to enable the Rename function. The Rename sign will move up to
indicate that Rename is selected. Use pq to highlight a channel and press OK to select it. A text field
will now pop up at the right of the screen. Use tu pq to select characters and enter them with OK.
When you have finished editing, press BLUE to enter the changes. When all changes have been made,
press EXIT twice. Select Yes to save the changes or No to discard.
Delete
Press BLUE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate
that Delete is selected. Use pq to highlight a channel and press OK to mark it for deletion. When
you have marked all channels you wish to delete, press EXIT twice. A confirmation banner will be
displayed. Select Yes to delete the marked channels or No to cancel.
7.1.2 Radio Channel List
Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only
difference is that in Radio Channel List there is no video information, so it will always display the radio
background on the preview screen.
7.1.3 Delete all
Use this menu to delete all stored channels. Select Delete All with pq and press OK. The receiver
asks you to enter the pin code. (DEFAULT PIN:1234). Inside the confirmation window select Yes with
tu and press OK to delete or select No to cancel.
Warning!The Delete all function will permanently delete all current channels and all
favourite lists from your receiver, and you are not able to leave the menu until
you search for channels again.
7.1.4 Rename Favourite list
This menu allows you to personalize the names of the 8 available favourite lists.
Use pq to select Rename Favourite List from the Edit Channel Menu and press OK to proceed. The
names of all groups are now displayed. Select a favourite group with pq and press OK to edit its
name. A text field will now pop up at the right of the screen. Use tu pq to select characters and
enter them with OK. When you have finished editing, press BLUE to save the changes. When all
changes have been made, press EXIT twice to leave this menu.
11
PART 1 • English
7.2 Installation
7.2.1 Auto Scan
Use pq to select Installation and press OK or u to advance.
Select Auto Scan with pq and press OK to enter.
Use tu to toggle between Yes or No. When FTA Only is set to Yes, scrambled channels won’t be
stored in the channel list. Use pq to highlight Search. Now press OK to start auto scan.
The receiver will store all found channels in the channel list.
7.2.2 Channel Scan
Use pq to select Installation, press OK or u to advance.
Use pq to select Channel Scan and press OK to enter.
Use tu to toggle between available scan modes: By Channel and By Frequency.
If By Channel is selected, use the cursor buttons to select Scan Band and Channel No. If By Frequency
is selected, use the cursor buttons to select Frequency and Bandwidth. Highlight Search and press OK
to start scanning. Newly found channels will be added to the channel list.
7.2.3 Antenna Power
Use pq to select Installation, press OK or u to advance.
Use pq to select Antenna Power and press OK to enter.
Set to On if you use an active antenna.
Select Off for passive antennas.
When set to On, 5 V will be present on the ANT IN connector of the receiver.
Press EXIT to leave the Antenna Power menu.
7.2.4 LCN (Logical Channel Numbering)
If LCN (Logical Channel Numbering) is activated and an LCN signal is provided by the operator,
channels will be stored in an operator defined order. Set LCN to On to activate operator defined
channel numbering or Off to store channels in found order. This function only applies when a new
channel search is performed.
7.3 System Setup
This menu allows you to manage the system settings of your receiver. It consists of the following
sub-menus: Language, TV System, Local Time Setting, Timer Setting, Parental Lock, OSD Setting and
Auto Standby.
Press pq to highlight the menu of choice and press OK advance to the next screen. Use pq to
move the highlight to the setting of choice. Values can be changed with tu. Press EXIT to leave.
7.3.1 Language
This menu allows you to set up your language preferences.
Language:
Use tu to select the language for the On Screen Display.
First Audio:
Use tu to select Audio language.
Second Audio:
Use tu to select a language that will be played when the language selected
at First Audio isn’t available.
12
Subtitle Language :
Teletext:
Subtitle:
se tu to select the preferred subtitle language.
U
Use tu to select the preferred Teletext language (when available).
Use tu to select the preferred subtitle type to be displayed automatically.
Select Normal, Hard of Hearing or Off*
* Availability of DVB/HoH subtitles depends on the broadcast. If such subtitles are not supported, then most likely subtitles can be activated via Teletext
if available.
7.3.2 TV System
Use this menu to match your receiver to your TV set. The following settings are available: Video
Resolution:
Use this option to select the video resolution of your TV screen. Options are:
By Source (automatic detection of video resolution offered to the receiver),
By Native TV (automatic detection of maximal resolution of TV screen), and
manual selections 480i, 576i up to 1080p Please use a setting that matches
your TV’s specifications. After a selection is made, you will be asked to
confirm. Selection above 576i is only applicable on HDMI output.
Aspect Mode:
Use this option to select the aspect ratio of your TV and the preferred
conversion method. The options are:
Auto (automatic detection of aspect ratio), 4:3 Panscan (Displays 16:9
widescreen broadcasts full screen on your 4:3 TV), 4:3 letterbox (black bars
on top and under the picture on a 4:3 TV) and 16:9 (use this setting for 16:9
TV sets).
Connection:
Use this option to select the connection to your TV set. Select HDMI or TV
SCART. If connection type HDMI is selected, then only the CVBS signal is
available on the TV SCART.
Digital Audio Output: Toggles between PCM and Bitstream output. When PCM is selected, all digital
audio will be converted to stereo audio. Bitstream enables you to listen or
transfer DolbyDigital/DolbyDigital+ audio to the TV via HDMI or to a Home
entertainment system (for example) through coaxial S/PDIF.
7.3.3 Local Time Setting
Here you can set up your region and time zone.
Region:
Use tu to select the region you live in.
GMT Usage:
Set to By Region for broadcaster defined time, User Define to select manual a
GMT zone or to Off to input time and date manually.
GMT Offset:
Allows you to adjust the time zone you live in. This option is only available
when GMT Usage is set to User Define.The GMT Offset range is "-11:30 ~
+12:00", increasing by half hours progressively. The cities matching the set
GMT Offset are displayed at the bottom of the screen.
Daylight Saving:
Select Off or On to add one hour extra for summer time during the summer.
Date:
Date and Time settings are available only when GMT Usage is set to Off. Use
the 0~9 buttons to enter the date. Press EXIT to proceed.
Time:
Date and Time settings are available only when GMT Usage is set to Off. Use
the 0~9 buttons to enter the time. Press EXIT to proceed.
Time DisplaySelect On to display time on screen, Off to remove.
13
English
PART 1 • English
PART 1 • English
7.3.4 Timer Setting
This menu allows you to set up to 8 timed events for recording or waking up the receiver.
Use pq to select Timer Setting from the System Setup menu and press OK to enter.
The receiver will display a list with 8 timers, followed by their respective status. Select the timer you
wish to set or change with pq and press OK to proceed.
The timer setup menu will now be displayed.
The following settings are available:
Timer Mode:
Choose between Off (Timer inactive), Once, Daily (Timer will be executed
every day, same time) or Weekly (Timer will be executed every week, same
day, same time) and Monthly (Timer will be executed every month, same day,
same time).
Timer Service:
Choose between Channel (Timer will wake up the receiver) or Record (Timer
will start to record the scheduled event).
Wakeup Channel:
Use tu to select the channel the timer will wake up with.
Wakeup Date:
Use the 0~9 buttons to input the date for the timed event.
Wakeup Time:
Use the 0~9 buttons to input the start time.
Duration:
Use the 0~9 buttons to input the timer duration.
When all settings are according to your wishes, use pq to move the highlight to Save and press OK
to confirm. To quit the timer without saving your settings, move the highlight to Cancel.
7.3.5 Parental Lock
This menu allows you to protect the installation menu and/or channels with a PIN code. You can also
enter a new PIN code in the Parental Lock menu.
Use pq to select Parental Lock from the System Setup menu and press OK to proceed. You will be
asked to enter your PIN code. (DEFAULT PIN: 1234)
Menu Lock:
Locks the installation menu. You can set Menu Lock to On or Off.
Parental Rating:
Choose between: Off, 4 years and up to 18 years. Channels with a parental
rating above the chosen age will be protected with a PIN code (if available in
your local broadcast.)
New Password:
Enter your new PIN code (4 digits) here.
Confirm Password:
Re-enter your PIN code here to confirm.
7.3.6 OSD Setting
This menu allows you to change settings for:OSD Timeout and OSD Transparency.
OSD Timeout:
Sets the time after which on screen banners and messages disappear. The
range is 1~10 seconds or Always On.
OSD Transparency:
To set the OSD transparency from Off ~ 40% with 10% steps.
Load Default OSD Setting:
Press OK to clear all OSD settings and reset to default values.
7.3.7 Auto Standby
Auto Standby is a new feature that helps you reducing power consumption. When set to 30 Min/1
Hour/2 Hours or 3 Hours, the receiver will switch to standby if it doesn’t receive any commands during
this time. Set Auto Standby to Off to deactivate the automatic standby function.
14
PART 1 • English
7.4 Tools
English
Press MENU in viewing mode to enter the Main Menu.
Select the Tools submenu with pq and press OK or u to enter.
Use pq to highlight the submenu of choice and press OK proceed.
Press EXIT to leave.
7.4.1 Information
This submenu shows receiver specific information such as hardware version and software version. It
also displays our web address www.strong.tv. Please have the Information screen on hand when you
call our hotline. The person who answers your call might ask for the information given in this screen.
7.4.2 Load Factory Settings
This option allows you to reset the receiver to factory settings, which clears all stored channels.
Warning!By resetting your receiver to factory default, all your settings and stored
channels will be permanently deleted. Please use this option with care.
Use pq to select Load Factory Settings in the Tools menu and press OK. You are asked to input your
PIN code.
Input the correct PIN code using the 0~9 (DEFAULT PIN: 1234). A confirmation window is displayed.
Select Yes to return to factory settings. Select No to cancel.
Press EXIT to leave.
7.4.3 S/W Upgrade by OTA
This receiver is equipped with an Over The Air software upgrade function. An Over The Air update
might not be available in your region. Please visit our website www.strong.tv or contact your local
service hotline for more information about this option.
7.4.4 Upgrade by USB
This feature allows you to upgrade receiver software via the USB port. When new software is available
for your receiver, it can be downloaded from our website www.strong.tv.
Place the software file (unzipped) in the root directory of your USB storage device (HDD, memory
stick etc.) and connect the device to the USB port of the receiver.
Select Upgrade by USB from the Tools menu and press OK to proceed.
The upgrade menu will now be displayed.
Use pq to select Upgrade Mode and choose option Allcode.
Use pq to select Upgrade File and choose the file containing the latest and correct software.
Once all settings are made, move the highlight to Start and press OK to start the upgrade process.
After a few seconds, the receiver asks: “Are you sure to burn flash?”. Select Yes to finalize the upgrade
or No to quit without upgrading.
If, after a software upgrade, the receiver should behave in an unexpected way, please perform a factory
reset as well. See chapter 7.4.2.
Warning!After an update the receiver restarts automatically. During the upgrade
process NEVER disconnect the receiver from the mains or switch off the
power! Doing so might damage your receiver and will void warranty!
15
PART 1 • English
7.5 Games
Your receiver is equipped with two games which can be played on your TV screen using the receiver
remote control.
Use pq to select Game from the Main menu and press OK or u to proceed.
Select one of the available games (Othello or Sudoku) using pq and press OK to start the game.
Follow the directions on screen. Press EXIT to quit a game.
7.6 Media
The Media menu consists of the following submenus: Media Player, HDD Information, DVR Setting
and Remove USB device safely.
Use pq to highlight the menu of choice and press OK to enter. Press EXIT to quit.
7.6.1 Media Player
This function allows playback of different kind of files from the connected USB storage device. In the
Media menu, select Media Player and press OK to enter this menu.
When entering the media player, the highlight is on the USB storage device. Press q and OK to open
the directory respectively its folders/subfolders.
First select which files you like to play back. Use the button 1 to switch between Video/Record/Music
or Image. Press pq to select a file or folder and then press OK to open the folder/subfolder (if
applicable) or start playback of the file. Press the EXIT button to exit.
Use the buttons like described below in order to choose functions during the different playback
modes (like described in the help banner below):
ideo:
V
INFO:
1:
2:
7:
EXIT:
Record:
2:
3:
4:
16
Press the INFO button to set repeat mode. The options are repeat folder
folder icon/repeat once 1 or no repetition (no icon shown).
During the playback of a movie with external subtitles, press 1 to enter
the subtitle menu. In this menu you can select size and colours of
your preference.
Press the button 2 to open the Sort menu. You can sort by Name/Time
or Size.
Press the button 7 to open the Edit menu. This menu allows accessing the
following functions by entering the number: rename 4, copy 5, delete 6, create
folder 7.
One step back or leave the folder and quit the function.
Press 2 to enter a new name for the selected recording.
Highlight the recording that you want to lock. After pressing 3 you will be
asked to input your PIN code. DEFAULT PIN: 1234. After entering your PIN
code, the recording is locked. If you want to unlock the recording again, press
3 again.
Press 4 to mark the recording you want to delete. By selecting the same
recording and pressing 4 again you can remove the delete marker again.
Press EXIT to delete.
PART 1 • English
Music:
4:
5:
6:
7:
2:
INFO:
EXIT:
Image:
4:
5:
6:
7:
2:
INFO:
3:
EXIT:
One step back or leave the folder and quit the function.
ress 4 to open a previously created play list. Then you can select the music
P
file that you want to add your play list by pressing 5 (a single file will be added
to the play list) or 6 (all files of this directory/folder will be added to the play
list).
Press 5 to add a file to the playlist. A favourite icon will be shown next to
the file.
Press 6 to add all files of this directory/folder to the play list. Press 6 again to
delete all files from the play list.
Press 7 to open the Edit menu. This menu allows accessing the following
functions by entering the number: rename 4, copy 5, delete 6, create folder 7.
Press button 2 to open the sort window. You can sort by Name/Time/Size
and Favourite.
Press the INFO button to set repeat mode. The option is Repeat Folder/
Random Folder/Repeat One.
One step back or leave the folder and quit the function.
ress 4 to open a previously created play list. Then you can select the image
P
file that you want to add your play list by pressing 5 (a single file will be added
to the play list) or 6 (all files of this directory/folder will be added to the play
list).
Press 5 to add a file to the play list. A favourite icon will be shown next to
the file.
Press 6 to add all files of this directory/folder to the play list. Press 6 again to
delete all files from the play list.
Press 7 to open the Edit menu. This menu allows you to accessing the
following functions by entering the desired number: rename 4, copy 5, delete
6, create folder 7.
Press button 2 to open the sort window. You can sort by Name/Time/Size
and Favourite.
Press INFO to access slideshow settings. You can change the slide time and
slideshow repetition.
Press 3 to show the files in a preview of 3x3 pictures.
One step back or leave the folder and quit the function.
7.6.2 HDD Information
This option shows relevant information about the connected USB device. In this menu you can also
format your USB storage device and setup the recording type.
Select HDD Information in the Media menu and press OK to enter.
Now you will see all details as Free and used Recording Sizes and used file system.
Press the YELLOW button Format to format the connected USB device.
Please, enter your PIN code to access this menu and press OK to start formatting.
17
English
EXIT:
PART 1 • English
Warning!Formatting will permanently delete ALL data stored on the connected device.
Please make a backup copy of all data you wish to keep before entering the
HDD Format menu. STRONG cannot be held responsible for loss of data
from USB devices used with this receiver.
Press OK to proceed, select FAT or Cancel, or press EXIT to leave without formatting.
It is possible to use USB storage devices already formatted in NTFS.
Press EXIT to leave this menu.
7.6.3 DVR Setting
This menu allows you to configure settings for Timeshift, recording and playback.
Select DVR Setting in the Media menu and press OK to enter.
Use pq to move the highlight and tu to change settings.
Timeshift:
Select between Auto, Pause or Off. When Timeshift is set to Auto it will
automatically start every time after tuning to a channel. When Timeshift is set
to Pause it will start only after pressing the YELLOW/2 button. Select Off to
deactivate Timeshift.
Step to:
30 sec to 30 min. Set the time step you like to jump forward by pressing 4
during playback of recorded files. This will only work when the info banner is
displayed on screen. If it is not, press INFO.
Time Shift to Record: If set to On the timeshifted part will be included in your recording when you
start to record the current programme.
PS Record:
Select between On or Off. When Off is selected, recordings will also
include subtitles and Teletext (when available). Record to PS mode On
allows recordings without these extras which will need less space on your
USB device.
Press EXIT to leave this menu.
7.6.4 Remove USB device safely
Select Remove USB device safely from the tools menu and press OK. The receiver will display a
message indicating that you can safely remove your storage device from the receiver.
Note:After performing this function, the USB device is no longer accessible from
your receiver. To gain access to your storage device again, re-insert it or switch
the receiver to standby and on again.
8.0 Troubleshooting
There may be various reasons for abnormal operation of the receiver. Check the receiver according to
the procedures shown below. If the receiver does not work properly after checking it, please contact
your dealer or the local Service Hotline. Do NOT try to open or disassemble the receiver. It may cause
a dangerous situation and warranty will be void.
Problem
Possible cause
LED indicator not lit
Mains lead unplugged
18
What to do
Check mains plug
PART 1 • English
Possible cause
What to do
Aerial is disconnected
Aerial is damaged/misaligned
Out of digital signal area
Active antenna requires to
switch ON antenna power/
external power
Check aerial lead
Check aerial
Check with dealer
Switch receiver’s Antenna
Power ON/connect external
power
No picture or sound on TV or
amplifier
HDMI or SCART is not
selected on your TV or
amplifier or the unit is set to
higher resolution as the TV
supports.
TV/amplifier is not switched on
Switch to correct TV/amplifier
input
Select lower resolution on
receiver
Switch TV/amplifier on.
Check if S / PDIF connection
is used.
Scrambled channel
Message
Channel is scrambled
Select alternative channel
No response to remote control
Receiver off
Remote not aimed correctly
Front panel obstructed
Remote batteries exhausted
Plug in and turn on plug
Aim remote at front panel
Check for obstructions
Replace remote batteries
Forgotten PIN code
Forgotten channel lock code
English
Problem
No signal found
Default PIN is 1234
Contact local Service Hotline
or send email to our Support
via www.strong.tv
After moving the receiver to
another room/area you are no
longer able to receive digital
reception
Antenna signals are too weak
The signal strength/quality
might be less than before, if
using an indoor antenna.
The receiver switches off
automatically.
Auto Standby function enabled. Disable auto standby. See
section 7.3.7 for details.
Playback of video (or
Timeshift) is causing picture
freeze/macro blocks or similar
distortion, especially on HD
content.
Read/write speed of your USB
device could be too low.
Press the INFO button on
remote 3x to call up signal
bars and adjust antenna for
(maximum) reception
or rescan channels
When using an active antenna,
check antenna power.
Try to use an outdoor antenna.
Make sure to use a USB
storage device with sufficient
speed and space. Pen drives
(‘USB sticks’) may not support
sufficient speed.
19
PART 1 • English
9.0 Technical Specifications
Demodulator
Demodulator:
Transmission mode:
Video Decoder
Profile level:
Video resolutions:
Decoding & Video out:
Aspect ratio:
OFDM; 16 QAM/64 QAM, QPSK
C
2 K - 8 K
MPEG-2 MP@ML, AVC/H264 HP@L4.1, MPEG4 ASP supported
4 80i / 480p / 576i / 576p / 720p / 1080i / 1080p / By Native TV /
By source
PAL
4:3 Letterbox, 4:3 Pan & Scan, 16:9, Auto
Audio Decoder
Audio support:
MPEG MusiCam Layer 2
Sampling rate:
Audio mode:
32, 44.1, 48 KHz
tereo, Mono
S
Tuner
Front End:
Input frequency range:
Loop through frequency range:
Input signal level:
VB-T, UHF & VHF Tuner
D
174 – 230 MHz (VHF) and 470 - 862 MHz (UHF)
47 - 862 MHz
-20 ~ -84 dBm
Memory and System
Flash memory:
SDRAM:
4 Mbytes
6 4 Mbytes
AAC/DD+*/AC3/PCM
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories
Multimedia
Video playback:
Audio playback:
Picture view:
PEG-1 and MPEG-2 encoded (mpg), VOB, AVI, MKV, TS, M2T,
M
M2TS, MPEG-4 and MOV*
MP3 and OGG *
BMP and JPEG *
STRONG cannot guarantee the playback of video files although extensions are listed, as it depends on codec used, data bit rate and resolution (all
MPEG codec formats are supported).
Connectors
ANT IN - IEC Female
ANT OUT - IEC Male
TV SCART (RGB, CVBS, Audio L&R)
HDMI 1.3
S / PDIF (coax.)
3.5 mm stereo audio jack (audio left/right)
USB 2.0 port: 5 V/800 mA (max.) supported
20
PART 1 • English
2 20 - 240 V AC (SMPS), 50/60 Hz
3.40 W (typ.), 12.00 W (max)
0.32 W
0 ~ +40° C
-30 ~ +80° C
10~85%, RH, Non-condensing
138 x 112 x 40
0.33 kg
English
General Data
Supply Voltage:
Power Consumption:
Power consumption in Standby:
Operating Temperature:
Storage Temperature:
Operating Humidity Range:
Size (WxDxH) in mm:
Net-weight:
21
PART 1 • English
22
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising