VCB-3442P - Multicare Electronics Ltd

VCB-3442P - Multicare Electronics Ltd
L73Q2/XE GB 2001, 5, 10
I
index
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
VCB-3442P
B/W CCD Camera
CCD-Schwarzweißkamera
Caméra CCD Noir et Blanc
CCD
About this manual
A propos de ce manuel
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Avant d’installer et d’utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
L73Q2/XE GB 2001, 5, 10
Depending on the conditions of use, installation and environment,
please be sure to make the appropriate settings and adjustments. If
you need help with installation and/or settings, please consult your
dealer.
CONTENTS
FEATURES
• Built-in interline transfer method 1/3" CCD, approx. 320,000
picture elements
• Low smear, anti-blooming, low lag, no burning and no geometric
distortion using the CCD solid state image device.
PRECAUTIONS..................................................................................... 2
PARTS NAMES..................................................................................... 3
MOUNTING THE LENS ........................................................................ 6
CONNECTIONS .................................................................................... 8
SETTINGS............................................................................................. 9
TROUBLESHOOTING........................................................................... 12
SPECIFICATIONS.................................................................................. 13
ACCESSORIES ...................................................................................... 14
English
1
• 100% solid state components giving excellent immunity to shock
and vibration
• Not subject to interference from magnetic or electrostatic fields
• High sensitivity, minimum required illumination of 0.05 lux with
F1.2 lens
• Horizontal resolution, more than 400 TV lines
• Backlight compensation function (Active when using an auto-iris
lens)
• Externally adjustable flange back (mechanical focus)
• Low power consumption and quick start
• 12 V DC operation
L73Q2/XE GB 2001, 5, 10
PRECAUTIONS
In case of problem
Do not use the camera if smoke or a strange odour comes from the
unit, or if it seems not to function correctly. Disconnect the power
cord immediately, and consult your dealer (or a Sanyo Authorized
Service Centre).
Do not open or modify
Do not open the cabinet, as it may be dangerous and cause damage
to the unit. For internal settings and repairs, consult your dealer (or a
Sanyo Authorized Service Centre).
Do not put objects inside the unit
Make sure that no metal objects or flammable substance get inside
the camera. If used with a foreign object inside, it could cause a fire,
short-circuits or damages.
If water or a liquid gets inside the camera, disconnect the power cord
immediately, and consult your dealer (or a Sanyo Authorized Service
Centre). Be careful to protect the camera from rain, sea water, etc.
Install away from electric or magnetic fields
If installed close to a TV, radio transmitter, magnet, electric motor,
transformer, audio speakers the magnetic field they generate will
distort the image.
Protect from high temperatures
Do not install close to stoves, or other heat generating devices, such
as spotlights, etc., or where it could be subject to direct sunlight, as
that could cause deformation, discoloration or other damages.
Be careful when installing close to the ceiling, in a kitchen or boiler
room, as the temperature may raise to high levels.
Install where the temperature range will stay between –10˚C and 50˚C.
(no condensation)
Cleaning
• Dirt can be removed from the cabinet by wiping it with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a
soft detergent solution and wrung dry, then wipe dry with dry soft
cloth.
• Do not use benzine, thinner or other chemical product on the
cabinet, as that may cause deformation and paint peeling. Before
using a chemical cloth, make sure to read all accompanying
instructions. Make sure that no plastic or rubber material comes in
contact with the cabinet for a long period of time, as that may
cause damage or paint peeling.
ENGLISH
Be careful when handling the unit
To prevent damages, do not drop the camera or subject it to strong
shock or vibration.
Protect from humidity and dust
To prevent damages to the camera, do not install it where there is
greasy smoke or steam, where the dampness may get too high, or
where there is a lot of dust.
2 English
L73Q2/XE GB 2001, 5, 10
PARTS NAMES
1 Camera setup section
4 5
1
2
SHUTTER
EI
AI
BLC
AGC
OFF
OFF
• Electronic iris (EI)/Auto iris (AI) setting
• Backlight compensation (BLC) setting
• Automatic gain control (AGC) setting
VIDEO OUT
2 Power indicator (POWER)
Comes on when the power to the camera is on.
POWER
DC12V
+
_
3 12 V DC input terminal (12 V DC, GND)
GND
4 High speed electronic shutter switch (SHUTTER)
3
5 Video output connector (VIDEO OUT: BNC type)
Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.
6
6 Lens iris level volume (LEVEL)
8
7
English
3
7 Auto-iris lens switch (DC/VIDEO)
8 Lens iris output connector (LENS)
L73Q2/XE GB 2001, 5, 10
PARTS NAMES
9 Flange-back lock screw
F Lens mount cap
9
The cap is installed to protect the lens mount section.
Remove the lens mount cap before installing a lens (sold separately).
F
G Camera installation bracket
The bracket can be fixed at the top or bottom of the camera.
A Camera mounting screw hole: 1/4"-20 UNC
CAUTION:
When installing the camera support, select a location that can support the total weight of the
camera and accessories.
G
A
4 English
L73Q2/XE GB 2001, 5, 10
PARTS NAMES
Concerning auto-iris lenses
DC type auto-iris lens
A lens without amplifier circuit that operates only on a DC power source. In general, this type of lens is
referred to as DC type coil lens or DC type non-amplifier lens.
(Set the Auto-iris lens switch to the DC position.)
H
LEVEL
L
DC
VIDEO
LENS
VIDEO type auto-iris lens
A lens with amplifier circuit that operates on video signal and DC power source. In general, this type of lens is
referred to as EE amplifier type lens.
ALC and LEVEL volume level controls are available on the lens for iris adjustments.
(Set the Auto-iris lens switch to the VIDEO position.)
Compatible auto-iris lenses
1/3 inch Sanyo DC type lens
VCL-CS8LY: Standard angle, f= 8 mm
VCL-CS4LY: Wide angle, f= 4 mm
VCL-CS2LY: Ultra-wide angle, f= 2.8 mm
VIDEO type lens
Standard angle, f= 9 mm
Telephoto angle, f= 12 mm
More telephoto angle, f= 16 mm
If using a VIDEO type auto-iris lens
• Set the ALC and LEVEL controls on the lens to adjust the iris. Normally the ALC volume should be turned
all the way to Av (Average).
• Depending on the type of lens used, the lens may not perform properly. In such a case, adjust the LEVEL
volume on the lens casing to correct.
English
5
L73Q2/XE GB 2001, 5, 10
MOUNTING THE LENS
Please use a DC type auto-iris lens (sold separately).
Checking the lens mount
Do not use a lens if length “L” is more than 9 mm. If not, that may damage the camera and prevent
proper installation.
L
1
2
1
C mount type lens 2
3
Remove the lens mount cap from the camera.
Install the auto-iris lens.
CS mount type lens
Carefully align the lens mount with the camera opening, then turn the lens slowly to install it.
C mount type lens
To allow for flange-back adjustment, install the C-mount adaptor (option) on the lens mount, then
carefully align the lens mount with the camera opening and turn the lens slowly to install it.
Connect the lens plug to the lens iris output connector (LENS) on the side of the camera.
When using lenses from other makers, the plug shape may not correspond to the terminal on the camera.
In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug
according to the diagram. (Refer to page 7.)
3
2
CS mount type lens
6 English
L73Q2/XE GB 2001, 5, 10
MOUNTING THE LENS
Rewiring the lens cable in the lens iris plug
1
1
2
2
Prepare the lens cable.
Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire.
Install the lens iris plug.
Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close
the plug cover.
Pin layout
2
1
3
4
2
1
4
3
1
2
3
4
DC type lenses
Brake coil (–)
Brake coil (+)
Drive coil (+)
Drive coil (–)
VIDEO type lenses
+10 V DC (50 mA max.)
Not used
Video output (1.0 Vp-p, high impedance)
Ground (for video signal and DC power)
Flange-back adjustment
1
If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus
(in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back
position as described below.
1
2
1, 3
English
7
2
3
4
5
Before installing the lens, check that the two flange-back lock screws have been tightened.
If the flange-back lock screws are loose, the CS mount ring will not be secured and it will not be possible to
adjust the flange-back.
Fully install the lens, then loosen the two flange-back lock screws.
Set the zoom lens to the maximum telephoto position (TELE), then set the focus using the focus ring on the lens.
Set the zoom lens to the maximum wide angle position (WIDE), then set the focus by turning the CS mount ring.
Repeat steps 3 and 4 until the image stays in focus when changing from a telephoto shot to a wide angle shot.
When the setting is complete, tighten the two flange-back lock screws.
L73Q2/XE GB 2001, 5, 10
CONNECTIONS
Basic connection for monitoring or recording
1
The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately.
1
2
(A)
2
Make the video signal connection between the camera and the monitor or time lapse VCR.
Connect DC connecting cord from the AC adaptor to the 12 V DC IN terminal on the camera.
WARNING:
• This AC adaptor is specially conceived for this camera. Never use another type of AC adaptor with this
camera, and do not use this AC adaptor to power other types of cameras.
• Not for use with toys.
• Never try to disassemble or modify the AC adaptor.
3
3
Insert the plug of this power cord into a wall outlet.
The POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast
controls.
Coaxial cable type and maximum length
• Cable type RG-59U (3C-2V), 250 m maximum.
• Cable type RG-6U (5C-2V), 500 m maximum.
• Cable type RG-11U (7C-2V), 600 m maximum.
CAUTION:
(Video signal connections)
: VIDEO IN
: VIDEO OUT
• The RG-59U type cable should not be run through electrical conduits or through the air.
• Using CCTV/Video-grade coaxial cable.
8 English
L73Q2/XE GB 2001, 5, 10
SETTINGS
Camera setup section
EI
BLC
AGC
AI
OFF
OFF
• Electronic iris (EI)/Auto iris (AI) setting
• Backlight compensation (BLC) setting
• Automatic gain control (AGC) setting
Electronic iris function setting
Use a manual or fixed iris lens and set the lens
aperture to the shortest F stop. Set the EI/AI
switch to EI position.
EI
AI
☞ When using an auto-iris lens (for indoor/outdoor use)
Set the EI/AI switch to the AI position.
Note:
• The electronic iris is suitable for normal indoor use. When the
EI/AI switch is set to the EI position, do not use an auto-iris lens.
• If used under fluorescent light, the image may flicker. In such a
case, change to incandescent lighting or set the EI/AI switch to
the AI position and use an auto-iris lens.
• When shooting bright subjects, pay attention to the light angle in
order to avoid or minimize the smear phenomenon effect.
• If conditions are outside the electronic iris operation range or more
than the maximum illumination, it will cause saturation of the CCD.
In that case, use a manual iris lens.
English
9
L73Q2/XE GB 2001, 5, 10
SETTINGS
Lens iris adjustment
If using a DC type auto-iris lens, you will need to set the LEVEL
volume when shooting in the conditions described below.
L (counterclockwise): To decrease the contrast
H (clockwise): To increase the contrast
• If shooting simultaneously in a dark room
and through a bright window.
• If the subject background is extremely
LEVEL
bright or dark.
• If the brightness of the picture on the
monitor is not correct.
Backlight compensation setting
Use an auto-iris lens and set the BLC switch to
the ON position, to engage the backlight
compensation function.
H
L
BLC
OFF
If using a VIDEO type auto-iris lens
• The ALC volume on the lens should be turned all the way to Av
(Average).
• If the backlight compensation function does not compensate
properly for the conditions, set using the LEVEL volume on the
lens.
AGC setting
AGC (Automatic gain control) can be turned ON or OFF.
AGC (ON): Auto gain control
AGC
OFF: Fixed gain
OFF
10 English
L73Q2/XE GB 2001, 5, 10
SETTINGS
High speed electronic shutter setting
Normally, the speed setting switch for the high
speed electronic shutter set to the 0 position.
This sets the electronic shutter speed to 1/50 sec.
The switch can be set as indicated in table A to
select one of the 8 speeds available.
0 1
7 6 5
2
3
4
CAUTION:
• When using the high speed electronic shutter, the EI/AI switch
must be set to the AI position.
• Using the high speed electronic shutter indoors with low lighting,
will give darker pictures. In such a case, add some lights to make
sure the lighting is sufficient. If the lighting is very bright, pay
attention to the light angle in order to avoid or minimize the
smear phenomenon effect.
Table A
0
1/50
1
1/120
2
1/250
3
4
5
6
7
1/500 1/1000 1/2000 1/4000 1/10000
(Unit: sec.)
English
11
L73Q2/XE GB 2001, 5, 10
TROUBLESHOOTING
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly,
please consult your dealer or a Sanyo Authorized Service Centre.
No picture on the monitor screen
Is the power turned on to all connected devices? Is the voltage correct?
Are all the signal connecting cables correctly connected?
Is the lighting sufficient?
Has the lens cap been removed?
Is the lens type (DC or VIDEO) correctly selected?
Depending on the type of lens, the A. I. LENS switch must be set accordingly.
• Is the iris control correctly set?
A: When using a DC type lens, the LEVEL volume should be adjusted.
B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted.
•
•
•
•
•
•
•
•
•
The picture is not clear
Is the monitor correctly adjusted?
Is the flange-back position correctly set?
Is the lens focus correctly adjusted?
Are the lens surfaces clean?
If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens
cleaning set.
12 English
L73Q2/XE GB 2001, 5, 10
SPECIFICATIONS
Scanning system
: CCIR standard (625 TV lines,
25 frames/sec.)
Interlace
: 2:1 interlace
Image device
: 1/3 inch solid state image device CCD
Picture elements
: 542 (H) x 584 (V)
Effective picture elements : 512 (H) x 582 (V)
Synchronizing system
: Internal sync
Resolution
: 400 TV lines horizontally, 400 TV lines
vertically
Video output level
: 1.0 Vp-p/75 ohms, composite
Video S/N ratio
: More than 50 dB
Minimum required
: Approx. 0.05 lux with a F 1.2 lens,
illumination
approx. 0.07 lux with a F 1.4 lens
(incandescent lighting)
Backlight compensation
: Manual ON/OFF switching, zone light
measuring system
(Active when using an auto-iris lens)
Electronic iris function
: Manual ON/OFF switching
High speed electronic
: 8 speeds, selectable by switch:
shutter
(1/50, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10000 sec.)
Electronic iris range
: 0.07 lux to 42,000 (F 1.4, lens)
0.05 lux to 30,000 (F 1.2, lens)
Flange-back
: 12.5 mm ± 0.8 mm
Gamma correction
: γ = 0.45
Lens mount
: CS mount
Environmental conditions : Temperature: –10˚C ~ +50˚C
Humidity: less than 90% (no
condensation)
Power supply
: 12 V DC
English
13
Power consumption
Weight
: 12 V DC/190 mA (with auto iris lens)
12 V DC/140 mA (without auto iris lens)
: Approx. 370 g (without lens)
AC Adaptor:
Environmental conditions : Temperature: –10˚C ~ +50˚C
Humidity: less than 90%
(no condensation)
Power requirement
: 220 – 230 V AC 50Hz
Power consumption
: 4.3 W (with auto iris lens)
3.7 W (without auto iris lens)
Weight
: Approx. 480 g
SERVICE
This camera is a precision instruments and if treated with care, will
provide years of satisfactory performance. However, in the event of a
problem, the owner is advised not to attempt to make repairs or open
the cabinet. Servicing should always be referred to your dealer or
Sanyo Authorized Service Centre.
L73Q2/XE GB 2001, 5, 10
ACCESSORIES
SPECIFICATIONS
Dimensions
135
123
7
1 Lens iris plug (4-pin)..................................................................1 pc.
2 AC adaptor ...............................................................................1 pc.
3 Hexagonal wrench....................................................................1 pc.
60
1
SHUTTER
3
AI
EI
60
2
VIDEO OUT
BLC
AGC
OFF
OFF
POWER
DC12V
29
40
+
_
GND
11
1/4”–20 UNC
28
81.4
48.9
1,830
1,830
58.5
Features and specifications are subject to change without prior
notice or obligations.
14 English
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising