Instruction Manual Bedienungsanleitung Manuel d

Instruction Manual Bedienungsanleitung Manuel d
RTF
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di istruzioni
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of
Horizon Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this
product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little
or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral
damage, and serious injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product, personal
property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury
or damage to the product or other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or augment product in any way
without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup
or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
• Always keep a safe distance in all directions around
your model to avoid collisions or injury. This model
is controlled by a radio signal subject to interference
from many sources outside your control. Interference
can cause momentary loss of control.
• Always use fully charged batteries.
• Always operate your model in open spaces away
from full-size vehicles, traffic and people.
• Always keep moving parts clean.
• Always carefully follow the directions and warnings
for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
• Always let parts cool after use before touching.
• Always keep all chemicals, small parts and anything
electrical out of the reach of children.
• Always keep transmitter powered on while aircraft is
powered.
• Always remove batteries before disassembly
• Always keep parts dry.
• Always remove batteries after use.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
• Always avoid water exposure to all equipment not
specifically designed and protected for this purpose.
Moisture causes damage to electronics.
• Never place any portion of the model in your mouth
as it could cause serious injury or even death.
• Never operate your model with low transmitter
batteries.
• Always keep aircraft in sight and under control.
• Always engage throttle hold at rotor strike.
EN
2
Introduction
As you are about to see, the Blade Nano CP X is an ultra micro heli experience unlike any other. The agility of the
advanced AS3X® (Artificial Stabilization – 3-aXis) Flybarless System and its feather-light airframe eclipse that of just
about every other heli its size. Inverted flight, loops, flips, rolls, funnels, hurricanes – the Nano CP X will do it all.
If you’re transitioning from a basic CCPM or fixed-pitched heli, you’ll find the Nano CP X is a great way to get comfortable
flying aerobatic CCPM helis without having to invest a lot in expensive equipment or repairs. Its AS3X Flybarless System
delivers a perfect balance of agility and stability that lets you explore your limits at your speed.
Before you start flying, though, please take time to read through this manual. It contains important pre-flight information
and useful tips that will help ensure your first flight, and every one after it, is the best it can be.
RTF
BLH3300
*Transmitter not included with BNF Version
BLH3380
Table of Contents
Charging Warnings............................................................4
Battery Charging ...............................................................4
AS3X Flybarless Helicopter Technology ...............................5
First Flight Preparation ......................................................5
Flying Checklist.................................................................5
Programming Your Transmitter ...........................................5
Transmitter and Receiver Binding .......................................7
Understanding the Primary Flight Controls ..........................8
Throttle Hold .....................................................................9
Stunt Mode.......................................................................9
Installing the Flight Battery ..............................................10
Low Voltage Cutoff (LVC) ..................................................10
Flying the Nano CP X.......................................................10
Troubleshooting Guide .....................................................11
Exploded View and Parts Listings .....................................12
Limited Warranty .............................................................14
Warranty and Service Contact Information ........................15
Customer Service Information ..........................................15
FCC Information ..............................................................16
Compliance Information for
the European Union .........................................................16
Blade Nano CP X Features
Airframe – Blade Nano CP X
Main and Tail Motors – Brushed
On-board Electronics – Flybarless 3n1 Control Unit, RX/ESCs/Gyros
Battery – 150mAh 1S 3.7V 25C LiPo Battery
Charger – 1-Cell 3.7V 0.3A DC Li-Po Charger
Transmitter – Requires a DSM2 ®/DSMX ® Compatible Transmitter
Transmitter Batteries – 4 AA
Ready To Fly
Included
Installed
Bind-N-Fly
Included
Installed
Installed
Installed
Included
Included
Included
Included
DX4e Included
Sold Separately
Included
Sold Separately
Blade Nano CP X Specifications
Length
Height
Flying Weight
7.75 in (197mm)
3.10 in (79mm)
1.00 oz (29 g)
Main Rotor Diameter
Tail Rotor Diameter
7.75 in (197mm)
1.60 in (40mm)
Visit www.bladehelis.com to register your helicopter
3
EN
Charging Warnings
The Battery Charger (EFLC1000) included with your
helicopter has been designed to safely charge the Li-Po
battery.
CAUTION: All instructions and warnings must be
followed exactly. Mishandling of Li-Po batteries can
result in a fire, personal injury and/or property damage.
• By handling, charging or using the included
Li-Po battery, you assume all risks associated
with lithium batteries.
• If at any time the battery begins to balloon or
swell, discontinue use immediately. If charging or
discharging, discontinue and disconnect. Continuing to
use, charge or discharge a battery that is ballooning or
swelling can result in fire.
• Always store the battery at room temperature in a dry
area for best results.
• Always transport or temporarily store the battery in a
temperature range of 40–120º F (5–49° C). Do not store
battery or model in a car or direct sunlight. If stored in a
hot car, the battery can be damaged or even catch fire.
• Always charge batteries away from
flammable materials.
• Always inspect the battery before charging
• Always disconnect the battery after charging, and let
the charger cool between charges.
• Always constantly monitor the temperature of the
battery pack while charging.
• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO
CHARGE LI-PO BATTERIES. Failure to charge the battery
with a compatible charger may cause a fire resulting in
personal injury and/or property damage.
• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places
(recommended between 40–120° F or (5–49° C) or
place in direct sunlight.
WARNING: For optional AC operation, only use an E-flite 6V power supply with this charger.
DO NOT use a 12V power supply or property damage and injury could occur.
Battery Charging
E-flite ® 1-Cell 3.7V Rate 0.3A DC Li-Po Charger
(EFLC1000) Instructions:
1. Charge only batteries that are cool to the touch and are
not damaged. Look at the battery to make sure it is not
damaged e.g., swollen, bent, broken or punctured.
2. Remove the cover on the bottom of the charger and
install four of the included AA batteries, noting proper
polarity. Replace the cover after the AA batteries are
installed.
3. Slide the battery into the slot on the charger. The end
cap of the battery is specifically designed to allow the
battery to fit into the slot one way (usually with the label
on the battery facing outward) to prevent reverse polarity connection. However, check for proper alignment
and polarity before proceeding to the next step.
4. Gently press the battery and its connector into the
charge jack/connector located at the bottom of the slot
in the charger.
5. When you make the connection successfully, the LED
on the charger turns solid red, indicating charging has
begun.
6. Charging a fully
discharged (not
over-discharged)
150mAh battery
takes approximately 20–30
minutes. As the
battery nears full
charge, the LED
begins to blink.
7. When the battery
is fully charged,
the LED blinks
approximately
every 20 seconds or goes out entirely.
If the LED stays on when the battery is removed, the
AA batteries in the charger are low.
8. Always remove the battery from the charger immediately upon completion of charging.
NOTICE: Only use the included charger. For DC charger
operation (AA batteries): only use alkaline AA batteries to
power the charger. Do not use rechargable AA batteries.
CAUTION: NEVER attempt to power the charger from an AC outlet without the use of a proper AC to DC
adapter/power supply.
WARNING: For AC operation, only use an E-flite 6V power supply with this charger. DO NOT use a 12V power
supply or property damage and injury could occur.
EN
4
AS3X Flybarless Helicopter Technology
The Blade® Nano CP X features on-board AS3X flybarless technology. AS3X® technology combines 3-axis gyro
stabilization with a new flybarless colective pitch rotor
head, resulting in less drag, fewer parts and increased
performance.
The AS3X technology also improves tracking, stability and
cyclic response for intermediate and advanced pilots.
However, the AS3X flybarless system is not a flying aid for
beginners.
First Flight Preparation
Flying Checklist
• Remove and inspect contents
• Charge the flight battery
• Install the four AA batteries in the transmitter
(RTF ONLY)
• Install the fully charged flight battery in the helicopter
• Program your computer transmitter (BNF ONLY)
• Test the controls
• Familiarize yourself with the controls
• Find a suitable area for flying
❏ Always turn the transmitter on first
❏ Plug the flight battery into the lead of the
3-in-1 control unit
❏ Allow the 3-in-1 control unit to initialize and
arm properly
❏ Fly the model
❏ Land the model
❏ Unplug the flight battery from the 3-in-1 control unit
❏ Always turn the transmitter off last
®
Programming Your Transmitter (Computer Transmitters Only)
Program your transmitter before attempting to bind or fly the helicopter. If the throttle and pitch programming
values are incorrect, the helicopter will not respond. Transmitter programming values are shown below for the
SpektrumTM DX6i, DX7, DX7s, DX8, and DX18. The Spektrum DX8, DX7s, and DX18 model files are also available for
download online at the Spektrum DX8 Community.
NOTICE: When using a Futaba® transmitter with a Spektrum DSM module, you must reverse the throttle channel
and rebind. Refer to your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba
transmitter manual for instructions on reversing the throttle channel.
DX6i
SETUP LIST
ADJUST LIST
Model Type
HELI
D/R & Expo
0-AILE
0-ELEV
0-RUDD
1-AILE
1-ELEV
1-RUDD
100%
100%
100%
85%
85%
85%
Travel Adj
THRO
AILE
ELEV
RUDD
GYRO
PITC
100%
100%
100%
100%
100%
100%
Reverse
THRO N
AILE N
ELEV N
RUDD N
GYRO N
PITC R
Swash Type
1 Servo 90
Timer
4:00
30%
30%
INH
30%
30%
INH
5
Thro Curve
NORM
STUNT
HOLD
0%
40% 60% 80% 100%
100% 100% 100% 100% 100%
10% 10% 10% 10% 10%
Pitc Curve
NORM
STUNT
HOLD
30%
0%
0%
40%
25%
25%
50%
50%
50%
75%
75%
75%
100%
100%
100%
EN
®
Programming Your Transmitter contd.
DX7/DX7se
SYSTEM LIST
FUNCTION MODE
Model Type
HELI
D/R & EXP
Swash Type
1 Servo 90
0-AILE
0-ELEV
0-RUDD
1-AILE
1-ELEV
1-RUDD
EXP
30%
30%
INH
30%
30%
INH
D/R
100%
100%
100%
85%
85%
85%
Travel Adj
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GEAR 100%
PIT.
100%
Thro Curve
NORM
ST-1
ST-2
HOLD
0%
100%
100%
0%
40%
INH
100%
0%
60%
80%
100%
0%
80%
INH%
100%
0%
100%
100%
100%
0%
Pitc Curve
NORM
ST-1
ST-2
HOLD
30%
0%
0%
0%
INH
INH
INH
INH
50%
50%
50%
50%
INH
INH
INH
INH
100%
100%
100%
100%
Reversing SW
THRO N
RUDD N
AILE N
GEAR N
ELEV N
PIT.
N
Timer
4:00
DX7s
SYSTEM SETUP
Model Type
HELICOPTER
Swash Type
1 Servo Normal
F-Mode Setup
Flight Mode: F Mode
Hold: Hold
Frame Rate
22ms
DSMX
FUNCTION LIST
D/R & Expo
0-AILE
100%
0-ELEV
100%
0-RUDD
100%
1-AILE
85%
1-ELEV
85%
1-RUDD
85%
SERVO SETUP
Travel
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GEAR 100%
PIT.
100%
30%
30%
0%
30%
30%
0%
Throttle Curve
NORM
0%
40% 60% 80% 100%
ST-1
100% 100% 100% 100% 100%
HOLD
0%
0%
0%
0%
0%
Pitch Curve
NOR
ST-1
HOLD
Timer
4:00
3:00
MODE
TIME
START
POS
Reverse
THRO N
AILE N
ELEV N
RUDD N
GEAR N
PIT.
N
30%
0%
0%
40%
25%
25%
50%
50%
50%
75%
75%
75%
100%
100%
100%
Basic Flying
Advanced Flying
Countdown
4:00 Tone/Vibe
Throttle Out
25
DX8/DX18
SYSTEM SETUP
Model Type
HELI
Swash Type
1 Servo Normal
F-Mode Setup
Flight Mode: F Mode
Hold: Hold
Frame Rate
22ms
DSMX
EN
FUNCTION LIST
D/R & Expo
0-AILE
100% 30%
0-ELEV
100% 30%
0-RUDD
100% 0%
1-AILE
85% 30%
1-ELEV
85% 30%
1-RUDD
85% 0%
2-AILE
85% 30%
2-ELEV
85% 30%
2-RUDD
85% 0%
SERVO SETUP
Travel
Reverse
THRO 100%
THRO N
AILE 100%
AILE N
ELEV 100%
ELEV N
RUDD 100%
RUDD N
GEAR 100%
GEAR N
PIT.
100%
PIT.
N
Throttle Curve
NORM
ST-1
ST-2
HOLD
Pitch Curve
NOR
ST-1
ST-2
HOLD
Timer
4:00
3:00
MODE
TIME
START
POS
6
0%
100%
100%
0%
40%
90%
100%
0%
60%
80%
100%
0%
80%
90%
100%
0%
100%
100%
100%
0%
30%
0%
0%
0%
40%
25%
25%
25%
50%
50%
50%
50%
75%
75%
75%
75%
100%
100%
100%
100%
Basic Flying
Advanced Flying
Countdown
4:00 Tone/Vibe
Throttle Out
25
®
Transmitter and Receiver Binding
If you purchased an RTF model, the transmitter is bound to the model at the factory.
To bind or re-bind your Nano CP X to your chosen transmitter, please follow the directions below:
Binding is the process of programming the receiver of the control unit to recognize the GUID (Globally Unique
Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2 ®/ DSMX ® technology equipped aircraft transmitter to the receiver for proper operation.
NOTICE: Use the Non-Computer Radio binding instructions if you are using a DX4e or DX5e transmitter
with the Nano CP X BNF.
9
Binding Procedure for Computer Radios:
1. Disconnect the flight battery from the helicopter.
2. Power off the transmitter and move all switches to the 0 position.
3. Connect the flight battery to the helicopter. The 3-in-1 Control unit LED flashes after 5 seconds.
4. Push the bind switch/button while powering on the transmitter.
5. After 2–3 seconds, release the bind switch/button.
6. Move the rudder control stick to full right. Continue to hold the rudder control stick to full right until the
blue LED on the 3-in-1 control unit is solid.
7. Release the rudder control stick.
8. Disconnect the flight battery and power the transmitter off.
NOTICE: The throttle will not arm if the transmitter’s throttle control is not put at the lowest position and the stunt
mode switch is not in the 0 position.
If you encounter problems, obey binding instructions and refer to the troubleshooting guide for other
instructions. If needed, contact the appropriate Horizon Product Support office.
For a list of compatible DSM2/DSMX transmitters, please visit www.bindnfly.com.
9
Binding Procedure for Non-Computer Radio (DX4e, DX5e)
1. Disconnect the flight battery from the helicopter.
2. Power off the transmitter and move all switches to the 0 position.
3. Connect the flight battery to the helicopter. The 3-in-1 Control unit LED flashes after 5 seconds.
4. Push the trainer switch or button while powering on the transmitter.
5. Move the rudder control stick to full left after the transmitter LED lights flash twice.
6. Release the trainer switch/button. Continue to hold the rudder control stick to full left until the blue LED
on the 3-in-1 control unit is solid.
7. Release the rudder control stick.
8. Push the trainer switch/button. The blue LED on the 3-in-1 control unit flashes to confirm the helicopter
is in non-computer mode.
9. Disconnect the flight battery and power the transmitter off.
NOTICE: If the swashplate moves up and down when the trainer switch is moved, the helicopter is in computer
transmitter mode; repeat binding procedure.
7
EN
Understanding the Primary Flight Controls
If you are not familiar with the controls of your Nano CP X, take a few minutes to familiarize yourself with them
before attempting your first flight.
Throttle (model viewed from left)
Mode 1
Mode 2
Descend
Ascend
Throttle up
Throttle down
Rudder (model viewed from top)
Mode 1
Nose Yaws Left
Rudder left
Mode 2
Nose Yaws Right
Rudder right
Elevator (model viewed from left)
Mode 1
Mode 2
Forward
Backward
Elevator up
Elevator down
Aileron (model viewed from back)
Mode 1
Left
Right
Aileron left
EN
Mode 2
Aileron right
8
Throttle Hold
Throttle hold is used to turn off the helicopter motors if the helicopter is out of control, in danger of crashing or
both. Activate throttle hold anytime the helicopter is in danger to reduce the chance of damaging the helicopter
in a crash. Throttle hold will stop the motor in normal or stunt mode.
Throttle Hold ON (DX4e)
Press the trainer button anytime to turn throttle hold ON after connecting the
battery to the helicopter. The blue LED flashes, indicating throttle hold is ON.
Throttle Hold OFF (DX4e)
1. Make sure the AUX switch is in the OFF position.
2. Lower the throttle stick.
3. Press the trainer button three times within 3 seconds. The blue LED is solid.
1.
2.
3.
X3
Throttle Hold ON (DX5e)
Pull the trainer switch anytime to turn throttle hold ON after connecting the
battery to the helicopter. The blue LED flashes, indicating throttle hold is ON.
Throttle Hold OFF (DX5e)
1. Make sure the Gear switch is in the (0) position.
2. Lower the throttle stick.
3. Pull the trainer switch three times within 3 seconds. The blue LED is solid.
1.
2.
3.
X3
Stunt Mode
Stunt Mode allows the helicopter to fly inverted and perform aerobatics. The throttle runs continuously when Stunt Mode
is ON, regardless of throttle stick position. Turn Stunt Mode OFF to return control to the throttle stick.
Use the AUX/ACT switch on the DX4e transmitter or Gear switch on the DX5e transmitter to activate Stunt Mode.
DX4e – AUX/ACT OFF – Normal Mode
AUX/ACT ON – Stunt Mode
DX5e – Ch 5 (0) – Normal Mode
DX5e – Ch 5 (1) – Stunt Mode
9
EN
Installing the Flight Battery
1. Lower the throttle and throttle trim to the lowest
settings.
2. Power on the transmitter.
3. Install the flight battery in the battery holder. Connect
the battery cable to the 3-in-1 control unit.
NOTICE: Do not allow the helicopter to move until the
blue LED on the 3-in-1 control unit is solid.
NOTICE: Always disconnect the Li-Po battery from the
3-in-1 control unit of the aircraft when not flying. Failure
to do so will render the battery unusable.
Low Voltage Cutoff (LVC)
Low voltage cutoff (LVC) protects the Li-Po battery from overdischarge in flight and activates when the battery reaches 3V
per cell under load. Set your transmitter timer for 4 minutes and land when the timer expires.
LVC Precautions and Guidelines
• Repeatedly activating LVC damages the flight battery and you will need to replace the battery.
• Always unplug the Li-Po battery from the flybarless unit at the end of each flight. Failure to unplug the Li-Po battery
during storage will over-discharge the battery and will prevent it from charging in the future.
• LVC does not protect the battery from over-discharge during storage.
• The warranty does not cover crash damage or battery damage.
Flying the Nano CP X
Consult local laws and ordinances before choosing a location to fly your aircraft. Select a large, open area
away from people and objects. The Blade Nano CP X can fly outdoors on a calm day or indoors in a gymnasium.
CAUTION: Please take a few minutes to familiarize yourself with the Blade Nano CP X primary controls before attempting your first flight. The Blade Nano CP X is more responsive than other Blade micro helicopters
like the Blade mSR. Seek help from an experienced pilot if you are new to collective pitch helicopters.
Takeoff
Gradually increase the throttle to allow the helicopter time to increase rotor head speed.
NOTICE: Do not give any aileron, elevator or rudder commands before takeoff or the helicopter may crash.
Flying
The helicopter lifts off the ground when the rotor head reaches a suitable speed, and you apply collective pitch.
Establish a low-level hover to verify proper operation of your helicopter.
For pilots new to collective pitch helicopters, familiarize yourself with your Nano CP X in normal mode and at low
rate. As you become more familiar with the helicopter’s response, adjust the rates, expo, pitch and throttle curves to
suit your flying style.
NOTICE: Always fly the helicopter with your back to the sun to prevent loss of flight control.
Landing
Establish a low level hover. Slowly lower the throttle until the helicopter lands. Make only small control corrections
during this time to avoid rotor blade strikes or other damage.
NOTICE: To minimize damage, always activate throttle hold in preparation for or during a crash.
EN
10
Troubleshooting Guide
Problem
Possible Cause
Reset controls with throttle stick and throttle
trim at center or lowest setting
Throttle at high position
Helicopter will not
initialize
Helicopter will not
spool up
Motor power decreases
during flight
Cannot turn off
throttle hold
Switches not in normal position
Pitch or throttle servo reversing improperly configured
Throttle hold on
Low battery voltage
Receiver uses default soft Low
Voltage Cutoff (LVC)
Stunt Mode switch still on
Throttle not at low position
Powers off when flying
upside down (inverted)
Stunt Mode off
Will not bind properly to
non-computer radio
Helicopter binds differently to
non-computer radios
Poor tail authority
Climb out rate is greatly
reduced
LED on receiver flashes
rapidly and aircraft will not
bind to transmitter (during
binding)
LED on receiver flashes
rapidly and aircraft will not
respond to transmitter (after
binding)
Tail boom is cracked
The tail rotor blade is warped
or bent.
Main gear has slipped on the main
shaft.
Transmitter is too near aircraft during
binding process
Bind switch or button was not held
while transmitter was powered on
Aircraft or transmitter is too close to
large metal object, wireless source or
another transmitter
Less than a 5-second wait between
first powering on transmitter and connecting flight battery to aircraft
Aircraft is bound to a different model
memory (ModelMatchTM radios only)
Flight battery/transmitter battery
charge is too low
Transmitter may have been bound to
a different model (or with a different
DSM Protocol)
Aircraft or transmitter is too close to
large metal object, wireless source or
another transmitter
Helicopter vibrates or
shakes in flight
Solution
Set flight mode to OFF/0 and exit throttle hold.
Reset servo reversing
Refer to “Programming your Transmitter”
Turn off HOLD with throttle low and trim centered or low.
Refer to “Throttle Hold”
Completely recharge flight battery
Recharge flight battery or replace battery that
is no longer performing
Set flight mode to OFF/ 0 and exit throttle hold.
Reset controls with throttle stick and throttle
trim at center or lowest setting
When flying, switch stunt mode to ON/1 before
flying inverted.
Release bind button/ switch after
applying left rudder. Do not hold the bind button/ switch after applying left rudder.
Replace tail boom
Twist rotor blade back into position
or replace.
Push main gear back into position.
Power off transmitter, move transmitter a larger
distance from aircraft, disconnect and reconnect flight battery to aircraft and follow binding
instructions
Power off transmitter and repeat bind process
Move aircraft and transmitter to another location and attempt binding again
Leaving transmitter on, disconnect and reconnect flight battery to aircraft
Select correct model memory on transmitter
and disconnect and reconnect flight battery to
aircraft
Replace/recharge batteries
Select the right transmitter or bind to the new
one
Move aircraft and transmitter to another location and attempt connecting again
Check main rotor blades and blade grips for
Damaged rotor blades, spindle or blade
cracks or chips. Replace damaged parts. Regrips
place bent spindle.
11
EN
Exploded View and Parts Listings
M
L
S
K
M
S
L
L
H
J
I
H
G
C
N
T
U
A
N
E
F
P
D
EN
T
R
12
V
J
O
Optional Parts
B
Part #
Description
BLH3318A
Blue Canopy Set: Nano CP X
BLH3320A
Blue Vertical Fin: Nano CP X
EFLC1004
CelectraTM 4 port charger
EFLC1005
AC to 6VDC 1.5-Amp Power Supply
DX6i Transmitter
DX7S Transmitter
P
DX8 Transmitter
Q
DX18 Transmitter
Part #
Description
Description
L BLH3313
Flybarless 3n1 Control Unit, RX/ESCs/
Gyros: Nano CP X
Feathering Spindle w/O-Rings &
Hardware: Nano CP X
M BLH3314
B BLH3302
Tail Boom Assembly w/Tail Motor/
Rotor/Mount: Nano CP X
Main Blade Grips with Bearings:
Nano CP X
N BLH3315
2x5x2 Bearing (2)
C BLH3303
Main Motor with Pinion: Nano CP X
O BLH3603
Tail Rotor: mCP X/2, Nano CP X
D BLH3304
Landing Skid and Battery Mount:
Nano CP X
P BLH3318
Yellow Canopy Set: Nano CP X
Q BLH3320
Vertical Fin with Decal: Nano CP X
E BLH3305
Main Frame with Hardware:
Nano CP X
R BLH3521
Canopy grommets (8)
F BLH3306
Main Gear: Nano CP X, Scout CX
S BLH3322
Rotor Head Linkage Set (4):
Nano CP X
G BLH3307
Carbon Fiber Main Shaft w/Collar &
Hardware: Nano CP X
H BLH3308
Servo Pushrod Set with ball link,
3pcs: Nano CP X
I
Complete Precision Swashplate:
Nano CP X
Part #
A BLH3301
BLH3309
J BLH3310
Main Rotor Blade Set w/Hardware:
Nano CP X
K BLH3312
Main Rotor Hub with Hardware:
Nano CP X
BLH3323
Hardware Set: Nano CP X
T SPMSH2025L 2.0 g Linear Long, 15mm Lead
U SPMSH2026L 2.1 g Linear Long, 38mm Lead
SPMR4400
DX4e DSMX 4-Channel Full Range Tx
EFLC1000
1-Cell 3.7V 0.3A DC Li-Po Charger
V EFLB1501S25 150mAh 1S 3.7V 25C Li-Po Battery
13
SPM6836
Servo Mechanics: 2.3 g 2030L
BLH3324
Spindle Tool Set: Nano CP X
EN
Limited Warranty
What this Warranty Covers
Horizon Hobby, Inc., (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be
free from defects in materials and workmanship at the date
of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i)
cosmetic damage, (ii) damage due to acts of God, accident,
misuse, abuse, negligence, commercial use, or due to
improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted
service by anyone other than a Horizon Hobby authorized
service center, (v) Product not purchased from an authorized
Horizon dealer, or (vi) Product not compliant with applicable
technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON
MAKES NO OTHER WARRANTY OR REPRESENTATION, AND
HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE
DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE
REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive
remedy shall be that Horizon will, at its option, either (i)
service, or (ii) replace, any Product determined by Horizon to
be defective. Horizon reserves the right to inspect any and all
Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof
of purchase is required for all warranty claims. SERVICE OR
REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED
IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF
HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of Horizon
exceed the individual price of the Product on which liability
is asserted. As Horizon has no control over use, setup,
final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury.
By the act of use, setup or assembly, the user accepts all
resulting liability. If you as the purchaser or user are not
prepared to accept the liability associated with the use of the
Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific
legal rights, and you may also have other rights which vary
from state to state. Horizon reserves the right to change or
modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup or
use of the Product has been started, you must contact your
local distributor or Horizon directly. This will enable Horizon
EN
to better answer your questions and service you in the event
that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com,
submit a Product Support Inquiry, or call 877.504.0233 toll
free to speak to a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is
compliant in the country you live and use the Product in,
please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack the
Product securely using a shipping carton. Please note that
original boxes may be included, but are not designed to
withstand the rigors of shipping without additional protection.
Ship via a carrier that provides tracking and insurance for
lost or damaged parcels, as Horizon is not responsible for
merchandise until it arrives and is accepted at our facility.
An Online Service Request is available at Horizon Hobby
Service Center. If you do not have internet access, please
contact Horizon Product Support to obtain a RMA number
along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your
complete name, street address, email address and phone
number where you can be reached during business hours.
When sending product into Horizon, please include your RMA
number, a list of the included items, and a brief summary
of the problem. A copy of your original sales receipt must
be included for warranty consideration. Be sure your name,
address, and RMA number are clearly written on the outside
of the shipping carton.
Notice: Do not ship LiPo batteries to Horizon. If you
have any issue with a LiPo battery, please contact the
appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your
original sales receipt verifying the proof-of-purchase
date. Provided warranty conditions have been met, your
Product will be serviced or replaced free of charge. Service
or replacement decisions are at the sole discretion of
Horizon.
Non-Warranty Service
Should your service not be covered by warranty service will be completed and payment will be required
without notification or estimate of the expense unless
the expense exceeds 50% of the retail purchase
cost. By submitting the item for service you are agreeing to payment of the service without notification. Service
estimates are available upon request. You must include this
request with your item submitted for service. Non-warranty
service estimates will be billed a minimum of ½ hour of
labor. In addition you will be billed for return freight. Horizon
accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website
Horizon Hobby Service Center.
NOTICE: Horizon service is limited to Product compliant in the country of use and ownership. If noncompliant product is received by Horizon for service,
it will be returned unserviced at the sole expense of
the purchaser.
14
Warranty and Service Contact Information
Country of
Purchase
Horizon Hobby
Address
4105 Fieldstone Rd
Horizon Service Center
Champaign, Illinois
(Electronics and engines)
61822 USA
United States of
America
4105 Fieldstone Rd
Horizon Product Support
Champaign, Illinois
(All other products)
61822 USA
Units 1-4 Ployters Rd
Staple Tye
United Kingdom Horizon Hobby Limited
Harlow, Essex
CM18 7NS
United Kingdom
Christian-Junge-Straße 1
Horizon Technischer
25337 Elmshorn
Germany
Service
Germany
14 Rue Gustave Eiffel
France
Horizon Hobby SAS
Zone d’Activité du Réveil Matin
91230 Montgeron
China
Horizon Hobby – China
Phone Number/Email Address
877-504-0233
Online Repair Request:
visit www.horizonhobby.com/service
877-504-0233
productsupport@horizonhobby.com
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
+49 (0) 4121 2655 100
service@horizonhobby.de
+33 (0) 1 60 47 44 70
infofrance@horizonhobby.com
Room 506, No. 97 Changshou Rd. +86 (021) 5180 9868
Shanghai, China 200060
info@horizonhobby.com.cn
Customer Service Information
Country of
Purchase
Horizon Hobby
Address
Phone Number/Email Address
Sales
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
(800) 338-4639
sales@horizonhobby.com
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
Germany
Horizon Hobby GmbH
Christian-Junge-Straße 1
25337 Elmshorn
Germany
+49 (0) 4121 2655 100
service@horizonhobby.de
France
Horizon Hobby SAS
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
+33 (0) 1 60 47 44 70
infofrance@horizonhobby.com
China
Horizon Hobby – China
Room 506, No. 97 Changshou Rd. +86 (021) 5180 9868
Shanghai, China 200060
info@horizonhobby.com.cn
United States of
America
15
EN
FCC Information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be
compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
Antenna Separation Distance
When operating your transmitter, please be sure to maintain a separation distance of at least 5 cm between your body
(excluding fingers, hands, wrists, ankles and feet) and the antenna to
meet RF exposure safety requirements as determined by
FCC regulations.
These illustrations show the approximate 5 cm RF exposure area and
typical hand placement when operating your transmitter.
Compliance Information for the European Union
AT
DE
HU
LV
RO
BE
DK
IE
MT
SE
BG
ES
IT
NL
SI
CZ
FI
LT
PL
SK
CY
GR
LU
PT
UK
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2012081003
Product(s):
Nano CP X RTF (Spektrum DX4e transmitter included)
Item Number(s):
BLH3300
Equipment class:
2
The object of declaration described above is in conformity with the requirements of the specifications listed below,
following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive
2006/95/EC:
EN 300-328 V1.7.1: 2006
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN 60950-1:2006+A12: 2011
EN55022: 2010
EN55024: 2010
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Aug 10, 2012
EN
Steven A. Hall
Executive VP – Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
16
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2012081002
Product(s):
Nano CP X BNF
Item Number(s):
BLH3380
Equipment class:
1
The object of declaration described above is in conformity with the requirements of the specifications listed below,
following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive
2006/95/EC:
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN 60950-1:2006+A12: 2011
EN55022: 2010
EN55024: 2010
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Aug 10, 2012
Steven A. Hall
Executive VP – Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of
their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and make sure that it is recycled in a manner that protects
human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you
purchased the product.
17
EN
©2012 Horizon Hobby, Inc
Blade, E-flite, AS3X, Celectra, Bind-N-Fly, DSM2, DSMX, and ModelMatch are trademarks or registered trademarks of Horizon Hobby, Inc.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.
D578,146. US 7,898,130. PRC ZL 200720069025.2. Other patents pending.
Created 5/12 35294 BLH3300/BLH3380
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising