1/10 Electric Stadium Truck ECX1000S|ECX1000SA|ECX1000SEU ECX1100S |ECX1100SA |ECX1100SEU Instruction Manual Bedienungsanleitung Manuel d’utilisation MANUALE Congratulations on your purchase of the ECX™ Circuit™ Stadium Truck. This 1/10 scale model introduces you to the sport of RC driving. Herzlichen Glückwunsch zum Kauf des ECX™ Circuit™ Stadium Truck. Dieses 1/10 Scale Model öffnet Ihnen die Welt des RC Car Sports. Nous vous félicitons pour l'achat du ECX™ Circuit™ Stadium Truck. Ce modèle 1/10 vous introduit au sport de la conduite RC. Congratulazioni per l’acquisto di questo Circuit™ Stadium Truck ECX. Questa vettura in scala 1/10 vi introdurrà nel mondo dei modelli RC. EN NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit http://www.horizonhobby.com and click on the support tab for this product. Meaning of Special Language: The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury. CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury. Age Recommendation: Not for children under 14 years. This is not a toy. • Keep all chemicals, small parts and anything electrical out of the Safety Precautions and Warnings reach of children. As the user of this product, you are solely responsible for operating • Never lick or place any portion of the model in your mouth as it in a manner that does not endanger yourself and others or result in could cause serious injury or even death. damage to the product or property of others. • Exercise caution when using tools and sharp instruments. This model is controlled by a radio signal subject to interference from • Take care during maintenance as some parts may have sharp edges. many sources outside your control. This interference can cause • Immediately after using your model, do NOT touch equipment momentary loss of control, so it is advisable to always keep a safe such as the motor, electronic speed control and battery, because distance in all directions around your model as this margin will help they generate high temperatures. You may burn yourself seriously avoid collisions or injury. touching them. • Do not put fingers or any objects inside rotating and moving parts, • Never operate your model with low transmitter batteries. as this may cause damage or serious injury. • Always operate your model in an open area away from cars, traffic • Always turn on your transmitter before you turn on the receiver in or people. the car. Always turn off the receiver before turning your transmitter • Never operate the model in the street or in populated areas for any off. reason. • Keep the wheels of the model off the ground when checking the • Carefully follow the directions and warnings for this and any operation of the radio equipment. optional support equipment (chargers, rechargeable battery packs, etc.) you use. Table of Contents Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Motor Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Vehicle Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Setting the Gear Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Charging the vehicle Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Electronic Speed Control (ESC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Charging Warnings and Precautions. . . . . . . . . . . . . . . . . . . . . . . . . 4 Electrical Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing Transmitter Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Shock Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Transmitter Battery safety precautions. . . . . . . . . . . . . . . . . . . . . . . 5 Fasteners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Removing the Vehicle Body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Installing the Battery in the Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Transmitter Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 FCC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Installing the Vehicle Body. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Compliance Information for the European Union. . . . . . . . . . . . . . 14 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 When You are Finished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 circuit EN Water-resistant Vehicle with Waterproof Electronics Your new Horizon Hobby vehicle has been designed and built with a combination of waterproof and water-resistant components to allow you to operate the product in many “wet conditions”, including puddles, creeks, wet grass, snow and even rain. While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle should NOT be treated like a submarine. The various electronic components used in the vehicle, such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most of the mechanical components are water-resistant and should not be submerged. Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after running in wet conditions. To maximize the long-term performance of your vehicle and to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance” section below must be performed regularly if you choose to run in wet conditions. If you are not willing to perform the additional care and maintenance required, then you should not operate the vehicle in those conditions. CAUTION: Failure to exercise caution while using this product and complying with the following precautions could result in product malfunction and/or void the warranty. General Precautions • Read through the wet conditions maintenance procedures and make sure that you have all the tools you will need to properly maintain your vehicle. • Not all batteries can be used in wet conditions. Consult the battery manufacturer before use. Do not use Li-Po batteries in wet conditions. • Most transmitters are not water-resistant. Consult your transmitter’s manual or the manufacturer before operation. • Never operate your transmitter or vehicle where lightning may be present. • Do not operate your vehicle where it could come in contact with salt water (ocean water or water on salt-covered roads), contaminated or polluted water. Salt water is very conductive and highly corrosive, so use caution. • Even minimal water contact can reduce the life of your motor if it has not been certified as water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle until the water is mostly removed from the motor. Running a wet motor at high speeds may rapidly damage the motor. • Driving in wet conditions can reduce the life of the motor. The additional resistance of operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or any wet conditions that will increase the load on the motor for an extended period of time. Wet Conditions Maintenance • Drain any water that has collected in the tires by spinning them at high speed. With the body removed, place the vehicle upside down and pull full throttle for a few short bursts until the water has been removed. CAUTION: Always keep hands, fingers, tools and any loose or hanging objects away from rotating parts when performing the above drying technique. • Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of compressed air, blow out any water that may be inside the recessed connector housing. • Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a garden hose. Avoid rinsing the bearings and transmission. NOTICE: Never use a pressure washer to clean your vehicle. • Use an air compressor or a can of compressed air to dry the vehicle and help remove any water that may have gotten into small crevices or corners. • Spray the bearings, drive train, fasteners and other metal parts with WD-40® solvent or any other water-displacing light oil. Do not spray the motor. • Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours. • Increase the frequency of disassembly, inspection and lubrication of the following: • Front and rear axle hub assembly bearings. • All transmission cases, gears and differentials. • Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight motor oil. Specifications Transmitter Electronic Speed Control (ESC) Frequency2.4GHz Input Voltage Battery Electric Capacity (FET) Forward 38 A cont./380 A peak Electric Capacity (FET) 19 A cont./190 A peak AA x 4 Servo Power Supply Output Torque Operating Speed Size 4.8V~6V (shared with receiver) 41.66 oz (3 kg-cm) at 6V 0.20 sec/60 degrees of travel 55.6 x 20 x 43.2mm 4.9–8.4V PWM Frequency 1kHz BEC Voltage 5.6V/1 A max at 7.2V Size (L x W x H) 66.8 x 57.6 x 48.3mm Weight 72 g circuit 3 EN Components 3 1.ECX™ Circuit™ 1/10-scale Short Course Truck 2.ECX™ 2.4GHz Transmitter 3. AA (4) Batteries 4. 2A Peak Battery Charger (DYN4113) 5.Dynamite® Speedpack™ 7.2V Ni-MH battery (DYN1050EC) 4 2 1 5 Vehicle Preparations Charging the vehicle Battery 1. Connect the AC power cord to the power slot on the charger, then connect the other end of the power cord to an AC power source. 2. The Power LED and Charging LED will turn GREEN when the charger is connected to the AC power source. 3. Connect the battery pack connector to the charge connector. 4. Press the On/Off button to charge the battery. The Charging LED turns RED. 5. When the battery pack is fully charged, the Charging LED will turn GREEN. 6. Press the On/Off button to stop charging. Disconnect the battery pack connector from the charge connector. CAUTION: If at any time during the charge process the battery pack(s) becomes hot to the touch, unplug the battery immediately and discontinue the charge process. The vehicle battery charger produces 2000 milliAmps (2 Amps) per hour. Divide the mAh capacity on the label of a battery by 2000 to know how long battery charging will require. For example, an 1800mAh battery requires 0.9 hours (54 minutes) to charge. 4 circuit Charging Warnings and Precautions • Read all safety precautions and literature prior to use of this product. • Never allow minors to charge battery packs. • Never attempt to charge dead or damaged batteries. • Never charge a battery if the cable has been pinched or shorted. • Never allow batteries or chargers to come into contact with moisture at any time. • Never charge batteries in extremely hot or cold places (recommended between 50–80°F or 10–26°C) or place in direct sunlight. • Always use only Ni-MH rechargeable batteries. This charger cannot charge batteries such as “heavy duty”, “alkaline”, “mercury” or “lithium" battery. • Always connect the positive red lead (+) and negative black lead (-) terminals of the battery to the charger terminals correctly. • Always disconnect the battery and charger after charging and let them cool between charges. • Always inspect the battery before charging. • Always terminate all processes and contact Horizon Hobby if the product malfunctions. • Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger. • Never connect more than one battery pack to this charger at a time. • Always constantly monitor the temperature of the battery pack while charging. • Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process. EN Installing Transmitter Batteries AUTION: If using rechargeable batteries, charge only C rechargeable batteries. Charging non-rechargeable batteries may cause the batteries to burst, resulting in injury to persons and/or damage to property. NEVER install damaged batteries, batteries of mixed types or batteries of different ages in the transmitter. Remove exhausted batteries. NEVER store the transmitter with batteries installed. Install 4 AA alkaline batteries into the transmitter, following the instructions provided for your radio system. We recommend using only alkaline AA batteries in the transmitter, however, it is possible to use rechargeable Ni-MH batteries. Transmitter Battery safety precautions • Never install damaged batteries. • Never install batteries of mixed types or of different ages in the transmitter. • Always remove exhausted batteries. • Always remove batteries before storing the transmitter. • Low battery power can result in loss of control of the RC vehicle. Removing the Vehicle Body Installing the Battery in the Vehicle A B 1. Turn the battery clips (A) clockwise to remove the battery strap (B). 2. Install a fully charged battery. 3. Install the battery strap. 4. Turn the battery clips counterclockwise to secure the battery strap. If desired, you can put foam blocks (ECX2015) in front of the battery so the weight of the battery increases rear traction or in back of the battery to increase steering response. circuit 5 EN Transmitter Controls Reverse Switch Battery Level Indicator Solid Red and Green: Battery voltage is good (Above 4V). Solid Red: Battery voltage is critically low (below 4V). Replace transmitter batteries. Throttle Dual Rate Adjusts the maximum amount of throttle the vehicle can be given Steering Rate Adjusts the amount the front wheels move when the steering wheel is turned left or right Throttle Trim Adjusts the neutral point of the electronic speed control Steering Trim Adjust to make the vehicle drive straight with no input at the steering wheel 6 circuit Allows you to change the direction of steering (ST. REV) and throttle (TH. REV) controls. (Default setting for steering and throttle is “REV”) Power Switch Power on or off the transmitter Steering Wheel Control steering. Right and Left steering with ST. REV Switch on REV (See Reverse Switch) Throttle Trigger Controls power to the motor for forward or reverse Reverse (See TH. REV (when TH. switch) REV switch on R) Forward Stop (when TH. REV switch on R) EN Getting Started 1. Power on the transmitter. 3. Do a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground. 2. Power on the ESC. 4. Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter. NOTICE: Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Properly seating the motor brushes will increase the life and performance of the motor. Installing the Vehicle Body circuit 7 EN Operation • ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off. • ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result. When You are Finished 1. Power off the Electronic Speed Control (ESC). 2. Disconnect the battery. 4. Remove the battery from the vehicle. 3. Power off the transmitter. 5. Recharge the battery. Motor Care • Seat the motor brushes by driving smoothly on a flat surface during use of the first battery charge. Failing to do so can greatly reduce motor peroformance and functional life. • Prolong motor life by preventing overheating conditions. Undue motor wear results from frequent turns, stops and 8 circuit starts, pushing objects, driving in deep sand and tall grass, and driving continuously up hill. • Over-temperature protection is installed on the ESC to prevent circuit damage, but cannot protect the motor from driving against heavy resistance. EN Maintenance Setting the Gear Mesh B The gear mesh has already been set at the factory. Setting the gear mesh is only necessary when changing motors or gears. C You must remove the vehicle’s gear cover (A) to make this adjustment. Proper gear mesh (how the gear teeth meet) is important to the performance of the vehicle. When the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat. Set the gear mesh by following these simple steps: A 1. Loosen the 2 motor screws (B). 2. Put a small piece of paper (C) between the pinion and spur gears. 3 Push the gears together while tightening the motor screws. 4. Rotate the gears to remove the paper. The gearing should move a small amount. 5. Reinstall the gear cover. Electronic Speed Control (ESC) Low voltage cutoff (LVC) protects the battery from overdischarge by activating when the battery reaches 1V per cell under load. The ESC will reset after approximately 10 seconds. The vehicle can then be driven slowly back to the driver for battery recharge. Important: When the motor is disconnected or damaged, the beep may not be heard. Notice: Continually driving to LVC may damage the battery. LED Color LED Status Flashing Green ON Li-Po at Power ON Flashing Red ON NORMAL Operation Ni-MH at Power ON Stop Solid Green ON Forward All OFF Forward (full speed) Red ON Reverse All OFF Reverse (full speed) Green ON Brake All Solid ON Sound Overheat All LEDs LEDs alternately flashing 1 beep per second Motor Stalled Red LED Flashing quickly 3 times, stopping, then repeating 1 beep per second Battery Over Voltage (over 10V) All LEDs Solid Red LED. Green LED flashing once per second 1 beep per second Battery Depleted/Discharged Red Flashing once per second 1 beep per second circuit 9 EN Electrical Layout Part # Description A DYN1171 Motor B DYN1050EC Battery 7.2V C DYN3900 Steering Servo D ECX9011 Receiver E DYN4925WP Electronic Speed Control (ESC) F Channel 1 G Channel 2 A E B EC3 EC3 D C G F For correct operation, Channels 1 and 2 must be used as shown in the wiring diagram. The motor can be disconnected from the ESC at the connectors in the wiring. Shock Cleaning Rear shock Rear Shock Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3 to 5 hours of use, depending on the conditions that the vehicle is used in. ECX1043 • Remove the shock from the vehicle. • Remove the cap from the shock body and dispose of fluid. • Disassemble the shock. Clean thoroughly with DYN5505. Dry parts before assembly. • Re-assemble the shock and refill the shock body with silicone fluid (30 weight recommended). • Slowly move the shaft and piston up and down to remove air bubbles. • Move the piston to the midway point of the body and install the cap. • Wipe off any overflowing fluid. • When properly filled, the piston should rebound about 3/8 in (9.5mm) after being pushed in fully. • Re-install the shock on the vehicle. Ride Height Adjustment Ride height is an adjustment that affects the way the vehicle jumps, turns and goes over bumps. Drop one end of the vehicle from approximately 6 inches (152 mm) in height onto a flat surface. When dropping the front of the vehicle, after the vehicle settles, make sure the front arms are equal and parallel to the flat surface. Do the same with the rear to make sure both arms are parallel with the flat surface. Lowering the front ride height increases steering, but decreases traction. Lowering the rear ride height increases traction, but decreases steering. 10 circuit front shock Front Shock ECX1037 ECX1057 ECX1038 ECX1036 ECX1038 ECX1043 ECX1037 ECX1037 ECX1043 ECX1037 ECX1038 ECX1036 ECX1038 ECX1043 ECX1037 ECX1040 ECX1039 ECX1041 ECX1042 ECX1038 ECX1037 ECX1057 ECX1037 Part # Description ECX1036 Shock Body Set ECX1037 Shock Caps, Pistons ECX1038 Shock Parts Set ECX1039 Front Shock Shaft (2) ECX1040 Rear Shock Shaft (2) ECX1041 Front Shock Springs (2) ECX1042 Rear Shock Springs (2) ECX1043 Shock O-Ring Set ECX1038 EN Fasteners No. Description No. Description No. Description TAPPING BINDER HEAD M3x10mm BINDER HEAD M3x20mm SETSCREW M3x3mm TAPPING BINDER HEAD M3x12mm BINDER HEAD M3x25mm SETSCREW M3x12mm TAPPING BINDER HEAD M3x16mm BUTTON HEAD M3x30mm SET SHAFT SCREW M3x13mm TAPPING BINDER HEAD M3x18mm BUTTON HEAD M2x6mm WASHER 5x7x0.5mm TAPPING FLAT HEAD M3x10mm TAPPING BUTTON HEAD M3x10mm WASHER 3x8x0.5mm TAPPING FLAT HEAD M3x12mm BUTTON HEX M2.5x4mm WASHER 2x7x0.5mm TAPPING FLAT HEAD M3x15mm BUTTON HEX M2.5x8mm FLANGED LOCK NUT M4 TAPPING FLAT HEAD M2x16mm STEP SCREW M3x0.5x7.4mm LOCK NUT M3 BINDER HEAD M3x8mm STEP SCREW M3x0.5x13.4mm E-CLIP E2.5 BINDER HEAD M3x12mm STEP SCREW M3x0.5x10.5mm LOCK WASHER Binding Failsafe A In the unlikely event the radio connection is lost during use, the receiver will reduce the throttle to idle. The steering channel holds the last input command. If you power on the receiver before powering on the transmitter, the receiver enters failsafe mode with throttle at idle. When you power on the transmitter, normal control resumes. Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. The included transmitter and receiver are bound at the factory. If you need to rebind, follow the instructions below. 1. Power off the transmitter and ESC. 2. Connect a fully charged battery pack to the ESC. 3. Power on the ESC. 4. Remove the front cover. Press the bind button (A) on the receiver. The RED LED on the receiver flashes rapidly. 5. Power on the transmitter. 6. The RED LED on the receiver turns solid when the system is bound. Replace the front cover. You must rebind when you want to use a different transmitter. circuit 11 EN Troubleshooting Guide Problem Possible Cause Solution Short Run Time • Battery damaged/not charged • Motor dirty or brushes worn • Check/change battery • Check/clean/replace Sluggish Action • Motor dirty or brushes worn • Bind in drivetrain • Vehicle battery is not charged • Check/clean/replace • Clean/adjust • Replace/recharge Controls Reversed • ST. REV or TH. REV • Change switch position Motor/ESC overheat • Over-geared • Install smaller pinion Doesn’t Operate • Transmitter batteries low • Transmitter powered off • ESC powered off • Vehicle battery is not charged • Replace/recharge • Power On • Power On • Replace/recharge Poor Range • Transmitter batteries low • Transmitter antenna is damaged or loose • Receiver antenna damaged • Replace/recharge • Check/tighten • Check/repair/replace The system will not connect • Transmitter and receiver too near each other • Transmitter and receiver too near large metal objects (vehicles, etc.) • Transmitter accidentally put in bind mode; receiver is no longer bound • Move transmitter 8–12 feet (2.4–3.6m) from receiver • Move away from large metal objects (vehicles, etc.) • Rebind transmitter and receiver The receiver goes into • Check the receiver antenna to ensure failsafe mode a short it is not cut or damaged distance away from the transmitter • Contact Horizon Product Support • Make sure receiver antenna is in an antenna tube and is above vehicle The receiver quits responding during operation • Completely recharge battery • Do a check of the wires and connection between battery and receiver. Repair or replace wires and/or connectors • Low battery voltage • Loose or damaged wires or connectors between battery and receiver Limited Warranty What this Warranty Covers - Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser that the product purchased (the "Product") will be free from defects in materials and workmanship at the date of purchase. What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations. OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE. Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all war- 12 circuit ranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase. Law - These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice. WARRANTY SERVICES Questions, Assistance, and Repairs - Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact EN your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call 877.504.0233 toll free to speak to a Product Support representative. Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_servicecenter_render-service-center. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office. Warranty Requirements - For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon. Non-Warranty Repairs - Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/_service-center_ render-service-center. NOTICE: Horizon service is limited to Product compliant in the country of use and ownership. If non-compliant product is received by Horizon for service, it will be returned unserviced at the sole expense of the purchaser. Contact Information Country of Purchase Horizon Hobby Address Phone Number/Email Address United States of America Horizon Service Center (Electronics and engines) 4105 Fieldstone Rd Champaign, Illinois 61822 USA 877-504-0233 firstname.lastname@example.org United Kingdom Horizon Hobby Limited Units 1-4 Ployters Rd, Staple Tye, Harlow, Essex, CM18 7NS, United Kingdom +44 (0) 1279 641 097 email@example.com Germany Horizon Technischer Service Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 firstname.lastname@example.org France Horizon Hobby SAS 14 Rue Gustave Eiffel, Zone d’Activité du Réveil Matin, 91230 Montgeron +33 (0) 1 60 47 44 70 email@example.com China Horizon Hobby - China Room 506, No. 97 Changshou Rd. Shanghai, China 200060 +86 (021) 5180 9868 firstname.lastname@example.org Horizon Product Support FCC Information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. circuit 13 EN Compliance Information forthe European Union Declaration of Conformity Instructions for disposal of WEEE by users in the European Union (in accordance with ISO/IEC 17050-1) No. HH2012090203 Product(s): ECX 1/10th Circuit V2.0 Item Number(s): ECX1000SEU/ECX1100SEU Equipment class: 1 The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC, EMC Directive 2004/108/ EC and LVD Directive 2006/95/EC: EN 300-328 V1.7.1: 2006 EN 301 489-1 V1.7.1: 2006 EN 301 489-17 V1.3.2: 2008 This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product. EN 60950-1:2006+A12: 2011 EN55022: 2010 EN55024: 2010 EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 Signed for and on behalf of: Horizon Hobby, Inc. Champaign, IL USA Steven A. Hall Sep 02, 2012 Executive Vice President and Chief Operating Officer International Operations and Risk Management Horizon Hobby, Inc. 14 circuit Parts Diagram | explosionszeichnung | vue éclatée des Piéces | esploso del modello con referenza pezzi Recommended Items Empfohlene Werkzeuge Outils Recommandés Attrezzi raccomandati M3x25 M3x12 M3x10 9 M3x10 M3x10 M3x25 46 11 3 4 7 11 M4.3x13 5 20 7 2 10 M4.3x13 1 8 45 2 2 46 8 M3 32 M3x18 12 7 M3x8 2 M3x12 M3x18 M3x12 44 47 30 32 17 M3x25 49 M3x12 M3x12 18 M3x13 32 M3x12 20 19 M2.5x4 16 20 M3x12 M3x16 M3x16 7 18 31 8 23 M4.3x13 53 M2x8 21 2 31 5 M4.3x13 M4.3x13 M3x18 22 M2.5x4 16 13 19 52 circuit Parts Diagram | explosionszeichnung | vue éclatée des Piéces | esploso del modello con referenza pezzi The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut. Then loosen the nut two full turns. Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060). Ziehen Sie die Mutter an und drehen Sie dann volle zwei Umdrehungen zurück. Il est possible d’ajuster l’embrayage “patinant” par action sur cet écrou de blocage (ECX1060). Veillez à serrer l’écrou de blocage à fond. Ensuite, devissez l’écrou de trois tours complets. La frizione può essere regolata con questo dado autobloccante (ECX1060). Prima avvitate complet-amente il dado, poi svitatelo 2 giri. 43 M3X3 33 M2.5X8 33 M2.5X4 42 22 35 35 35 35 35 15 M2.5X8 6 34 48 48 15 15 36 15 34 15 37 25 39 36 34 M3X18 38 M2X16 34 36 40 41 34 37 M3X12 40 34 34 36 34 36 34 M2X16 39 25 M3X12 M3x20 M3x20 44 M3x12 M3x16 M3x12 17 25 49 M3x16 28 32 M3x16 20 27 26 32 M3x12 M3x18 M3x12 26 30 27 28 15 11 31 24 3 M2.5x4 29 19 M2.5x4 21 M3x12 M3x12 14 14 M3x10 When installing wheel, make sure drive hex is aligned with the drive pin. When the drive hex is removed, the drive pin can fall out of the axle. Bitte achten Sie bei der Radmontage darauf, dass die Radachse im Radmitnehmer sitzt und dass der der Querstift nicht heraus fällt. Lors de l’installation de la roue, assurez-vous que l’écrou hexagonal est aligné avec la broche de l’axe d’entraînement. En cas de démontage de l’écrou hexagonal, la broche de l’axe d’entraînement peut sortir de l’axe et tomber. Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfilarsi dal mozzo. 22 circuit 53 54 Part # | Nummer Description Numéro | Codice Beschreibung Description Descrizione 1 ECX1017 Main Chassis Chassis Châssis principal Telaio principale 2 ECX1028 Servo Saver Set Servo Saver Set Jeu de sauvegarde de servo Set salvaservo 3 ECX1092 Rear Suspension Mount Set Querlenkerhalter hinten Jeu de renfort de suspension arriére Supporti braccetti sosp. posteriori 4 ECX1050 Setscrew M3x12 (4) Schrauben Set M3x12 (4) Jeu de vis M3x12 (4) Grani M3x12 (4) 5 ECX1053 Foam Block Schaum Block Bloc de mousse Spugna distanziale batteria 6 ECX1052 Motor Screw/Washer Set Motor Screw/Washer Set Vis Moteur/Set Rondelles Viti per il motore/ set di rondelle 7 ECX1058 Ball Stud (6) Kugelkopf (6) Rondelle (6) Sfere Uniball (6) 8 ECX1065 Shoulder Screw Set (8) Passschrauben Set (8) Jeu de vis d’épaulement (8) Set viti a doppio stadio (8) 9 ECX9011 Receiver Empfänger Récepteur Ricevente 10 DYN3900 Servo Servo Servo Servo 11 ECX1088 Battery Hold Down Akkuhalter Fixation pour batterie Piastra fermabatteria Set paraurti ant/post 12 ECX1091 Front/Rear Bumper Set Stoßstange vorne hinten Jeu de pare-chocs avant/ arrière 13 ECX1005 Chrome Wheel Ribbed Tire (2) Front Chrom Räder mit Rillenreifen (2) Pneu strié pour jante chromée (2) Gomme rigate su cerchi cromati (2) 14 ECX1006 Chrome Wheel Spiked Tire (2) Rear Chrom Räder mit Noppenreifen (2) Pneu á crampons pour jante chromée (2) Gomme Off Road su cerchi cromati (2) 15 ECX1015 Wheel Bearing Set Radlagersatz Set Jeu de roulement de roue Set cuscinetti ruote Braccetti delle sospensioni anteriori 16 ECX1018 Front Suspension Arm Set Querlenker Set vorne Jeu de bras de suspension avant 17 ECX1020 Shock Tower Set Dämpferbrücke Jeu de support d’amortisseur Supporto ammortizzatori posteriori 18 ECX1035 Front Axle (2) Radachse vorne (2) Axe avant (2) Mozzi ruota anteriori (2) 19 ECX1044 Hinge Pin Set Querlenkerbolzen Set Jeu de broche d’axe Set perni sospensioni Set tiranteria Camber e convergenza 20 ECX1046 Camber, Toe Link Set Spur- Sturzstangenset Jeu de biellette de cambrure, de pincement 21 ECX1049 Wheel Pins (4) Radmitnehmerstifte (4) Broches de roue (4) Spine trascinatori ruote (4) 22 ECX1060 M4 Locknut (4) M4 Stopmutter (4) Ecrou de blocage M4 (4) Dadi autobloccanti M4 (4) 23 ECX1089 Steering Block Set Lenkhebel Set Jeu de bloc de direction Fuselli sterzo Braccetti delle sospensioni posteriori 24 ECX1019 Rear Suspension Arm Set Querlenker Set hinten Jeu de bras de suspension arrière 25 ECX2100 Transmission Case Set Getriebegehäuse Ensemble carter de transmission Set scatola trasmissione 26 ECX230000 Driveshaft Set Antriebswellen Set Ensemble arbre de transmission Set semiassi 28 ECX230001 Rear Axle (2) Wellenmitnehmer hinten (2) Axe arrière (2) Mozzi ruota anteriori (2) 29 ECX1045 Hinge Pin Screws (8) Querlenkerbolzen Schrauben (8) Vis de broche d’axe (8) Viti per perni sospensioni (8) 30 ECX1070 ESC Regler/ESC CEV Variatore elettronico (ESC) 31 ECX1090 Rear Hub Carrier Set Hinterer Rad Träger Set Jeu de porte-moyeu arrière Portamozzi posteriori Obturateurs d’amortisseur, pistons Set tappi e pistoni ammortizzatori 32 ECX1037 Shock Caps, Pistons Stoßdmämpferkappen Kolben 33 ECX1027 Gear Cover Gear Cover Carter de Réducteur Copertura per ingranaggi 34 ECX1022 Transmission Gear Set Getriebe Ensemble couronne de transmission et ingranaggi trasmissione 35 ECX1024 Slipper Clutch Plates, Pads, Spring Rutschkupplung Teilesatz Plateaux d’embrayage Piattelli frizione, disco, patinant, plaquettes, ressort molla circuit Part # | Nummer Description Numéro | Codice Beschreibung Description Descrizione Hauptgetriebewelle Set Arbre secondaire de transm-ission, axes d’entraînement Alberino intermedio con spina 36 ECX1025 Transmission Idler Shaft, Drive Pins 37 ECX1026 Transmission Drive Shaft (2) Getreibeausgangswelle (2) Axe d’arbre de transmission Mozzi Differenziale (2) (2) 38 ECX1052 Washer Set Unterlegscheiben Set Jeu de rondelles Set rondelle 39 ECX1055 Bearings 10x15x4 (2) Lager 10x15x4 (2) Roulements 10x15x4 (2) Cuscinetti 10x15x4 (2) 40 ECX1059 M3 Locknut (4) M3 Stopmutter (4) Ecrou de blocage M3 (4) Dadi autobloccanti M3 (4) 41 ECX1076 Spur Gear Hauptzahnrad Couronne Corona 42 ECX1073 19-Tooth Pinion Gear 19-Tooth Pinion Gear Pignon 10 dents Pignone a 19 denti 43 DYN1171 Motor Motor Moteur Motore 44 ECX1048 Body Clip Body Clip Clips Carrosserie Clippe per carrozzeria 45 ECX1056 Bushing 3x6x2.8mm (2) Buchse 3x6x2.8mm (2) Bague 3x6x2,8mm (2) Boccole 3x6x2.8mm (2) 46 ECX1029 Top Plate Chassioberteil Plque frontale Piastra superiore 47 ECX1093 Body Mount Set Body Mount Set Set Montage Carrosserie Set di montaggio per la carrozzeria 48 ECX1023 Top Shaft/Spacer Top Shaft/Spacer Set de Goupilles Set di spessori 49 ECX1033 Setscrew M3x10 Sicherungsschrauben (4) Vis (4) Viti (4) circuit 55 ECX1000S, ECX1000SA, ECX1000SEU | ECX1100S, ECX1100SA, ECX1100SEU www.ecxrc.com 33331.1 Revised 8/2012 © 2012 Horizon Hobby, Inc. Horizon Hobby, ECX, Boost, Dynamite and Speedpack are trademarks or registered trademarks of Horizon Hobby, Inc. WD-40 is a registered trademark of WD-40 Manufacturing Company.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project