BCS-727 BCS-323 BCS-HW929 BCS-HF828 BCS-SB626

BCS-727 BCS-323 BCS-HW929 BCS-HF828 BCS-SB626
FRANÇAIS
Blu-ray Disc receiver
Système Home-Cinéma Blu-ray Disc
Blu-ray Disc Receiver
Sintoamplificatore con predisposizione Blu-ray Disc
Blu-ray Disc receiver
receptor de Blu-ray Disc
S-BD421
S-BD121
S-BD921HW
S-BD821HF
S-BD621FS
S-BD521FS
Speaker System
Enceintes acoustiques
Lautsprechersystem
Sistema di diffusori
Luidsprekersysteem
Sistemas de parlantes
ESPAÑOL
S-BD921SW
Subwoofer / Enceinte d’extrêmes graves / Subwoofer /
Subwoofer / Subwoofer / Altavoz de subgraves
Operating Instructions / Mode d’emploi / Bedienungsanleitung /
Istruzioni per l’uso / Handleiding / Manual de instrucciones
NEDERLANDS
XV-BD421W
XV-BD121W
XV-BD921FSW
XV-BD821FSW
XV-BD621FSW
XV-BD521FSW
ITALIANO
DEUTSCH
Blu-ray Disc surround system
Système Home-Cinéma Blu-ray Disc
Blu-ray Disc Mehrkanal-System
Sistema surround con lettore Blu-ray Disc
Blu-ray Disc multikanaals systeem
sistema surround de Blu-ray Disc
ENGLISH
BCS-727
BCS-323
BCS-HW929
BCS-HF828
BCS-SB626
BCS-FS525
Safety Information
Thank you for buying this Pioneer product.
Please read through these operating instructions so you will know how to operate your model properly.
After you have finished reading the instructions, put them away in a safe place for future reference.
IMPORTANT
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_A1_En
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007.
CLASS 1 LASER PRODUCT
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 10 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
D58-5-2-2a_A1_En
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower pot)
or expose it to dripping, splashing, rain or moisture.
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
D3-4-2-1-7c*_A1_En
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
CAUTION
The STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-2-2a*_A1_En
D3-4-2-1-7a_A1_En
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
Symbol examples
for batteries
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
Pb
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
K058a_A1_En
Cautions on 3D Viewing
• If you should experience any fatigue or discomfort while viewing 3D images, stop viewing them.
• Children, particularly those under 6, may be more prone to sensitivity, so guardians should watch
for any signs of fatigue or discomfort.
• When viewing 3D images, rest periodically.
Extended viewing of 3D images without rest periods could cause fatigue or discomfort.
For Wireless product European Union Notice
Notes on Copyrights
PIONEER hereby declares that
this/these product(s) is/are in
compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC, 2004/108/EC, 2006/95/EC
and 2009/125/EC.
• Because AACS (Advanced Access Content
System) is approved as content protection
system for Blu-ray Disc format, similar to use
of CSS (Content Scramble System) for DVD
format, certain restrictions are imposed on
playback, analog signal output, etc., of AACS
protected contents. The operation of this
product and restrictions on this product may
vary depending on your time of purchase
as those restrictions may be adopted and/
or changed by AACS after the production of
this product.
Indoor Use Only
RF Radiation Exposure Statement
This equipment should be installed and
operated with minimum distance 20 cm
between the radiator and your body.
WARNING
Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: THE MANUFACTURER IS NOT
RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
• Furthermore, BD-ROM Mark and BD+ are
additionally used as content protection
systems for Blu-ray Disc format, which
imposes certain restrictions including
playback restrictions for BD-ROM Mark
and/or BD+ protected contents. To obtain
additional information on AACS, BD-ROM
Mark, BD+, or this product, please contact
an authorized Customer Service Center.
• Many BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should
only connect your player directly to your TV,
not to a VCR. Connecting to a VCR results
in a distorted picture from copy-protected
discs.
• This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
• Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized
recording, use, display, distribution, or
revision of television programs, videotapes,
BD-ROM discs, DVDs, CDs and other
materials may subject you to civil and/or
criminal liability.
Important Notice for TV colour
system
The colour system of this player differs
according to currently playing discs.
For example, when the player plays the disc
recorded in the NTSC colour system, the image
is output as an NTSC signal.
Only the multi system colour TV can receive all
signals output from the player.
• If you have a PAL colour system TV, you will
see just distorted images when using discs
or video contents recorded in NTSC.
• The multi system colour TV changes the
colour system automatically according to
input signals. In case that the colour system
is not changed automatically, turn it off and
then on to see normal images on screen.
• Even if the disc recorded in NTSC colour
system are well displayed on your TV, these
may not be recorded correctly on your
recorder.
Table of Contents
1
Before you start
8Introduction
8
– Supplied accessories
8
– Accessories of speaker box (BCS-727)
8
– Accessories of speaker box (BCS-323)
8
– Accessories of speaker box (BCS-HW929)
9
– Accessories of speaker box (BCS-HF828)
9
– Accessories of speaker box (BCS-SB626)
9
– Accessories of speaker box (BCS-FS525)
10 – Putting the batteries in the remote control
10 – Software update
11 – Types of discs/files that can be played
17 – Trademarks and licenses
18 Remote control
20 Front panel
21 Rear panel
21 – BCS-727/BCS-323
21 – BCS-HW929/BCS-HF828/BCS-SB626/BCSFS525
2Connecting
22
22
23
24
24
25
25
26
26
27
28
29
29
30
32
33
33
34
35
Assemble the speakers
– Speaker setup for BCS-727
– Wall mounting the speaker for BCS-727
– Additional notes on speaker for BCS-727
– Positioning the system for BCS-727
– Speaker setup for BCS-323
– Wall mounting the speaker for BCS-323
– Additional notes on speaker for BCS-323
– Positioning the system for BCS-323
– Speaker setup for BCS-HW929
– Wall mounting the speaker for BCS-HW929
– Additional notes on speaker for BCS-HW929
– Positioning the system for BCS-HW929
– Speaker setup for BCS-HF828
– Wall mounting the speakers for BCS-HF828
– Additional notes on speaker for BCS-HF828
– Positioning the system for BCS-HF828
– Speaker setup for BCS-SB626
– Wall mounting the speaker for BCS-SB626
36
40
41
41
42
42
43
43
43
44
44
45
45
46
46
47
47
49
51
51
51
– Additional notes on speaker placement for
BCS-SB626
– Positioning the system for BCS-SB626
– Speaker setup for BCS-FS525
– Wall mounting the speakers for BCS-FS525
– Additional notes on speaker placement for
BCS-FS525
– Positioning the system for BCS-FS525
Connecting to Your TV
– HDMI connection
– ARC (Audio Return Channel) function
– Video connection
Antenna connection
Connections with external device
– AUX connection
– PORTABLE IN connection
– OPTICAL IN 1/2 connection
– HDMI IN 1/2 connection
– Connecting optional Bluetooth® ADAPTER
Connecting to your Home Network
– Wired network connection
– Wireless network connection
– Wireless network setup
– WPS setup (Wi-Fi Protected Setup)
USB device connection
– About USB devices
– Connecting the USB device
3
Getting Started
52
Making settings using the Setup Navigator
menu
Operating the TV with the player’s remote
control
– TV preset code list
36
37
39
40
53
54
4Playback
55
56
56
56
56
56
56
56
Playing discs or files
– Forward and reverse scanning
– Playing specific chapters, tracks or files
– Skipping content
– Playing in slow motion
– Step forward and step reverse
– Playing a specific section within a title or
track repeatedly (A-B Repeat)
– Playing repeatedly (Repeat Play)
57
– Playing in the desired order (Programmed
Play)
57 – Making bookmarks
57 – Zoom
58 – Playing photos as slideshows
58 – Switching the camera angles
58 – Switching the subtitles
59 – Switching the audio
59 – Switching the CD/SACD playback area
59 – Displaying the disc information
60 – Enjoying BONUSVIEW or BD-LIVE
61 – Playback functions
62 Using the TOOLS menu
62 – Playing from a specific time (Time Search)
63 – Playing a specific title, chapter, track or file
(Search)
63 – Playing specified range of discs, titles or
chapter (track/file) in random order
63 – Continuing playback from a specified
position (Continued Viewing Playback)
72
72
72
72
72
73
– Listening to the radio
– Presetting the radio stations
– Deleting all the saved stations
– Improving poor FM reception
– Seeing information about a radio station
Bluetooth® ADAPTER for Wireless Enjoyment
of Music
73 – Wireless music play
73 – Listen to music on a Bluetooth wireless
technology enabled device
74Karaoke
75Sound
8
Advanced settings
76
76
83
84
Changing the settings
– Operating the initial setup screen
– Software updating
– Restoring all the settings to the factory
default settings
– Language code table and country/area
code table
85
5
Playback from Home Media
Gallery
64
64
66
66
66
67
67
67
67
About Home Media Gallery
– About network playback
Playback file on the network
Disc/USB playback
– Playing back image files
Playing in the desired order (Playlist)
– Adding tracks/files
– Playing the playlist
– Deleting tracks/files from the playlist
6
Playing the web contents
68
68
Available web contents
Playing the items
7
Other Operating
69
70
70
71
72
Recording Audio CD to a USB device
iPod/iPhone playback
– Connecting your TV
– Playing your iPod/iPhone
Radio Operations
1
2
3
4
5
9Troubleshooting
86
87
87
88
88
90
– Picture
– Sound
– Playback
– Control function
– Network
– Others
10Appendix
91Specifications
95Maintenance
95 – Handling the unit
95 – Notes on discs
96 Important Information Relating to Network
Services
6
7
8
9
10
8
En
Before you start
Chapter 1
Before you start
1
Accessories of speaker box
(BCS-727)
Before you start
Introduction
Supplied accessories
Non-skid pads (2)
Screws M4 x 16 (16)
(They are used to fix to the
base and lower cabinet.)
Video cable (1)
Remote control (1)
Screws M4 x 12 (8)
(They are used to fix the
upper and lower cabinet.)
Battery (2)
FM antenna (1)
iPod cradle (1)
Power cord
• Warranty card (1)
• Operating instructions (This document)
Accessories of speaker box
(BCS-323)
Non-skid pads (6)
Screws M3.5x12
[Taping type] (4)
(These screws are used
to fix the speakers to the
stands.)
Accessories of speaker box
(BCS-HW929)
Bracket (2)
Large non-skid pads (1)
• Wire stays (4)
Non-skid pads (1)
Before you start
Accessories of speaker box
(BCS-HF828)
9
En
Accessories of speaker box
(BCS-FS525)
1
Stand arm (2)
Bracket (2)
Large non-skid pads (1)
Large non-skid pads (1)
Small non-skid pads (1)
Large poles (2)
Small poles (2)
Large screws (4)
Small screws (8)
• Screw (Bind head) (2)
• Screw (Flat head) (4)
• Hexagonal nut (2)
• Seal (1)
Accessories of speaker box
(BCS-SB626)
Speaker stand bases (2)
Screws (2)
Speaker stand bases (2)
WARNING
Small non-skid pads (1)
Store small parts out of the reach of
children and infants. If accidentally
swallowed, contact a doctor immediately.
Before you start
Base (2)
10
En
Before you start
Putting the batteries in the
remote control
1
1. Open the rear cover.
WARNING
Before you start
• Do not use or store batteries in direct sunlight or
other excessively hot place, such as inside a car
or near a heater. This can cause batteries to leak,
overheat, explode or catch fire. It can also reduce
the life or performance of batteries.
Caution
Press lightly on
this part and slide
into the direction
of the arrow.
2. Insert the batteries (AAA/R03 x 2).
Insert as indicated by the +/* marks into
the battery compartment.
Insert the
negative (*)
side first.
3. Close the rear cover.
Close securely (a click should be heard).
• Do not use any batteries other than the ones
specified. Also, do not use a new battery together
with an old one.
• When loading the batteries into the remote control,
set them in the proper direction, as indicated by
the polarity marks (+ and *).
• Do not heat batteries, disassemble them, or throw
them into flames or water.
• Batteries may have different voltages, even if they
look similar. Do not use different kinds of batteries
together.
• To prevent leakage of battery fluid, remove the
batteries if you do not plan to use the remote
control for a long period of time (1 month or more).
If the fluid should leak, wipe it carefully off the
inside of the case, then insert new batteries. If a
battery should leak and the fluid should get on your
skin, flush it off with large quantities of water.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public institution’s rules that apply in your country/
area.
Software update
Product information on this player is provided
on the Pioneer website. Check this website for
update and service information on your Blu-ray
disc player.
The batteries included with the player
have been provided to allow you to check
product operation and may not last long. We
recommend using alkaline batteries that have
a longer life.
IN Europe:
http://www.pioneer.eu/
IN U.K.:
http://www.pioneer.eu/
http://www.pioneer.co.uk/
IN Russia:
http://www.pioneer.eu/
http://www.pioneer-rus.ru/
IN Hong Kong:
http://www.pioneerhongkong.com.hk/
IN Singapore:
http://www.pioneer.com.sg/firmwaredownload
IN Australia:
http://www.pioneer.com.au/
Before you start
11
En
Types of discs/files that can be played
Playable discs
1
Discs with the logo marks below indicated on the disc label, package or jacket can be played.
Disc type
BD2
Logo
Application format
DVDCD-DA
DVD VR
Video
DTS-CD
DATADISC1
BDMV
BDAV
BD-ROM
BD-R
BD-RE
1
1
1
1
1
1












DVD-ROM
1

1


1
DVD-R2,3,4
1
6
1
7
1
1

1
DVD-RW3,7
1
6
1
7
1
1

1
DVD
DVD+R2,3
1

1


1
DVD+RW3
1

1


1
CD-DA
(Audio CD)8




1

CD-R3




1
1
CD-RW3
CD-ROM








1
1
1
1
CD
1. Discs on which video, image or audio files are recorded. This player does not support multisession discs or multiborder
recording.
2 Including dual-layered discs.
3. Finalize them before playing them on this player.
4 DVD-R for Authoring discs (3.95 and 4.7 GB) cannot be played.
5. Including the AVCHD format.
6. Including the AVCREC format.
7. Version 1.0 DVD-RW discs cannot be played.
8. Including Video CDs.
Before you start
Caution
• Only the discs that have been finalized can be played.
12
En
Before you start
• "Blu-ray Disc", "Blu-ray" and "Blu-ray Disc" logo
are trademarks of Blu-ray Disc Association.
1
•
is a trademark of DVD Format/Logo
Licensing Corporation.
Before you start
 Discs that cannot be played
• HD DVDs
• DVD-RAM discs
It is possible that some discs other than the
ones listed above may not be playable either.
Note
• Some discs cannot be played, even if one of the
logo marks on the previous page is indicated.
• To play 8 cm discs, set the disc in the 8 cm disc
depression in the center of the disc tray. No
adapter is necessary. 8 cm BD-ROMs cannot be
played.
 About playback of unauthorized
copies
Cinavia Notice
This product uses Cinavia technology to
limit the use of unauthorized copies of some
commercially-produced film and videos and
their soundtracks. When a prohibited use of an
unauthorized copy is detected, a message will
be displayed and playback or copying will be
interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com.
To request additional information about Cinavia
by mail, send a postcard with your mailing
address to: Cinavia Consumer Information
Center, P.O. Box 86851, San Diego, CA, 92138,
USA.
Copyright 2004-2010 Verance Corporation.
Cinavia™ is a Verance Corporation trademark.
Protected by U.S. Patent 7,369,677 and
worldwide patents issued and pending under
license from Verance Corporation. All rights
reserved.
 About audio formats
The following audio formats are supported on
this player:
• Dolby TrueHD
• Dolby Digital Plus
• Dolby Digital
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• MPEG audio (AAC)
• Linear PCM
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535;
7,392,195; 7,272,567; 7,333,929; 7,212,872 &
other U.S. and worldwide patents issued &
pending. DTS-HD, the Symbol, & DTS-HD and
the Symbol together are registered trademarks &
DTS-HD Master Audio | Essential is a trademark
of DTS, Inc. Product includes software. © DTS,
Inc. All Rights Reserved.
 Playing BDs
• BDs (BDMV) compatible with the formats
below can be played.
–– Blu-ray Disc Read-Only (ROM) Format
Version 2
–– Blu-ray Disc Recordable (R) Format
Version 2
–– Blu-ray Disc Rewritable (RE) Format
Version 3
This player supports BD-ROM Profile 5.
"Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of Blu-ray Disc Association.
BONUSVIEW functions such as playback
of secondary video (Picture-in-Picture) and
secondary audio can be used. The data
used with the BONUSVIEW functions (the
secondary video (Picture-in-Picture) and
secondary audio data) may be stored in the
storage. For details on secondary video and
secondary audio playback, refer to the disc’s
instructions.
Before you start
13
En
 Playing DVDs
"BONUSVIEW" is trademark of Blu-ray Disc
Association.
This label indicates playback compatibility with
DVD-RW discs recorded in VR format (Video
Recording format). However, for discs recorded
with a record-only-once encrypted program,
playback can only be achieved using a CPRM
compatible device.
The AVCHD is a high definition (HD) digital
video camera recorder format recording highdefinition onto certain media by using highly
efficient codec technologies.
"AVCHD" and the "AVCHD" logo are trademarks
of Panasonic Corporation and Sony Corporation.
"BD-LIVE" logo is trademark of Blu-ray Disc
Association.
With BD-ROMs, it is possible to use
BD-J (Java) applications to create highly
interactive titles, for example including
games.
 About region numbers
Blu-ray Disc Player and BD-ROM or DVD-Video
discs are assigned region numbers according
to the region in which they are sold.
This player’s region numbers are:
• BD-ROM:
–– Europe, Australia and New Zealand
models: B
–– Russia models: C
–– Others: A
• DVD-Video:
Oracle and Java are registered trademarks of
Oracle and/or its affiliates. Other names may
be trademarks of their respective owners.
• BDs (BDAV) compatible with the formats
below can be played.
–– Blu-ray Disc Recordable (R) Format
Version 1
–– Blu-ray Disc Rewritable (RE) Format
Version 2
–– Europe models: 2
–– Australia and New Zealand models: 4
–– Russia models: 5
–– Others: 3
Discs not including these numbers cannot be
played. Discs playable on this player are as
shown below.
• BDs:
–– Europe, Australia and New Zealand
models: B (including B) and ALL
–– Russia models: C (including C) and ALL
–– Others: A (including A) and ALL
• DVDs:
–– U.K. models: 2 (including 2) and ALL
–– Australia and New Zealand models: 4
(including 4) and ALL
–– Russia models: 5 (including 5) and ALL
–– Others: 3 (including 3) and ALL
1
Before you start
BD-LIVE functions such as downloading
movie trailers or additional audio and
subtitle languages and playing on-line
games can be enjoyed over the Internet. The
data downloaded with the BD-LIVE function
(trailers, etc.) is stored in the storage. Refer
to the disc’s instructions for details about
BD-LIVE functions.
14
En
Before you start
 Playing CDs
1
Before you start
Regarding copy protected CDs: This player
is designed to conform to the specifications
of the Audio CD format. This player does not
support the playback or function of discs that
do not conform to these specifications.
 DualDisc playback
A DualDisc is a two-sided disc, one side of
which contains DVD content - video, audio,
etc. - while the other side contains non-DVD
content such as digital audio material.
The DVD side of a DualDisc can be played on
this player.
The non-DVD, audio side of the disc is not
compatible with this player.
It is possible that when loading or ejecting
a DualDisc, the opposite side to that being
played will be scratched. Scratched discs may
not be playable.
For more detailed information on the DualDisc
specification, please refer to the disc
manufacturer or disc retailer.
 Playing discs created on computers or
BD/DVD recorders
• It may not be possible to play discs recorded
using a computer due to the application
settings or computer’s environment settings.
Record discs in a format playable on this
player. For details, contact the dealer.
• It may not be possible to play discs
recorded using a computer or a BD/DVD
recorder, if burn quality is not good due to
characteristics of the disc, scratches, dirt on
the disc, dirt on the recorder’s lens, etc.
 About video, audio, and image files
and folders
Audio and image files can be played on this
player when the folders on the disc or USB
device are created as described below.
Example of folder structure:
Root
001.jpg/001.mp3
*
xxx.jpg/xxx.mp3
01 Folder
*
Folder
001.jpg/001.mp3
xxx.jpg/xxx.mp3
001.jpg/001.mp3
XX Folder
xxx.jpg/xxx.mp3
*
001.jpg/001.mp3
*
xxx.jpg/xxx.mp3
* The number of folders and files within a
single folder (including the root directory) is
limited to a maximum of 256. Also, keep the
number of folder layers to a maximum of 5.
Note
• The file and folder names displayed on this player
may differ from those displayed on a computer.
Before you start
Playable files
Video, image and audio files recorded on
DVDs, CDs or USB devices can be played.
• In DVD, only the one recorded by the ISO 9660 file
system can be played.
• Some files may not be playable.
• For some files, it may not be possible to use certain
functions during playback.
• It may not be possible to play some files, even if
they have the extension of a file playable on this
player.
• Files protected by DRM (Digital Rights
Management) cannot be played (not including
DivX VOD files).
 Supported video file formats
• DivX Plus HD
DivX Certified® to play DivX® and DivX
PlusTM HD (H.264/MKV) video up to 1080p
HD including premium content.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX
Certified® device that plays DivX video. Visit
divx.com for more information and software
tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order
to play purchased DivX Video-on-Demand
(VOD) movies. To obtain your registration
code, locate the DivX VOD section in your
device setup menu. Go to vod.divx.com for
more information on how to complete your
registration.
DivX®, DivX Certified®, DivX PlusTM HD and
associated logos are trademarks of Rovi
Corporation or its subsidiaries and are used
under license.
En
Note
• This DivX® Certified device must be registered
in order to play DivX Video-on-Demand (VOD)
content. First generate the DivX VOD registration
code for your device and submit it during the
registration process. Important: DivX VOD content
is protected by a DivX DRM (Digital Rights
Management) system that restricts playback to
registered DivX Certified devices. If you try to play
DivX VOD content not authorized for your device,
the message Authorization Error will be displayed
and your content will not be played. Learn more at
www.divx.com/vod.
–– This player’s DivX VOD registration code can
be checked at HOME MENU d Initial Setup d
Playback d DivX(R) VOD DRM d Registration
Code (page 78).
–– The number of views is restricted for some
DivX VOD files. When such files are played on
this player, the remaining number of views is
displayed. Files for which the remaining number
of views has reached 0 cannot be played (This
DivX rental has expired is displayed). Files for
which the number of views is not restricted
can be played as many times as you like (the
remaining number of views is not displayed).
1
Before you start
Caution
15
16
En
Before you start
 Table of Playable Files
Playable media
1
Before you start
BD-R/RE/-R DL/
Playable files
RE DL/-R LTH,
(Extensions) DVD-R/RW/-R DL/
+R/+RW/+R DL,
CD-R/RW
USB devices1
Network2
File specifications
MP3
(.mp3)
1
1
1
Sampling frequencies: Up to 48 kHz
Bit rate: Up to 320 kbps
Audio type: MPEG-1 Audio Layer 3
WMA
(.wma)
1
1
1
Sampling frequencies: Up to 48 kHz
Bit rate: Up to 192 kbps
Audio type: WMA version 9
LPCM
(.wav)
1
1
1
Sampling frequencies: Up to 192 kHz
Quantization bitrate: 16 bit
Channel: 2ch
FLAC
(.flac)
1
1

Sampling frequencies: Up to 192 kHz
Quantization bitrate: 16 bit, 24 bit
Channel: 2ch
JPEG
(.jpg/.jpeg)
1
1
1
Maximum resolution: 4 000 x 3 000 pixels
DivX
(.avi/.divx/.mkv)
1
1
1
Supported versions: Through DivX® PLUS HD
Maximum resolution:
Up to 1 920 x 1 080 (DivX® PLUS HD)
Up to 1 280 x 720 (MKV)
MP4
(.mp4)
1
1
1
Maximum resolution: Up to 1 920 x 1 080
Video: MPEG4, MPEG-4 AVC (level 4.1)
Audio: AAC, MP3
WMV
(.wmv)
1
1
1
Maximum resolution: Up to 1 280 x 720
Video: WMV9, WMV9AP (VC-1)
Audio: WMA
AVI
(.avi)
1
1
1
Maximum resolution: Up to 1 920 x 1 080
Video: MPEG4
Audio: MP3, AAC, AC-3
1. This unit supports FAT16, FAT32 and NTFS file systems.
2. A requirement for playing files as a DMP. For details, see page 64.
Note
• Depending on the file structure and server capacity, it may not be possible to play certain files, even for files
indicated on the table of playable files above.
• Copyright-protected files and contents recorded from digital broadcasts (satellite, cable or digital terrestrial)
cannot be played via LAN.
• Files protected by DRM (Digital Rights Management) cannot be played.
• AVCHD contents cannot be played via LAN.
Before you start
17
En
Trademarks and licenses
1
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,226,616; 6,487,535;
7,392,195; 7,272,567; 7,333,929; 7,212,872 &
other U.S. and worldwide patents issued &
pending. DTS-HD, the Symbol, & DTS-HD and
the Symbol together are registered trademarks
& DTS-HD Master Audio | Essential is a
trademark of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
DLNA®, the DLNA Logo and DLNA CERTIFIED®
are trademarks, service marks, or certification
marks of the Digital Living Network Alliance.
The Wi-Fi CERTIFIED Logo is a certification
mark of the Wi-Fi Alliance.
The Wi-Fi Protected Setup Mark is a trademark
of the Wi-Fi Alliance.
“x.v.Colour”,
and
trademarks of Sony Corporation.
are
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod, or
iPhone, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod or
iPhone may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod
touch are trademarks of Apple Inc., registered in
the U.S. and other countries.
YouTube™ is a trademark of Google Inc.
Picasa™ Web Albums is a trademark of
Google Inc.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
Before you start
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other
countries.
18
En
Before you start
Remote control
• • • • • • • • • 1• • • • • • • • • 1
Before you start
1
 (STANDBY/ON): Press to turn the power on
and off.
FUNCTION: Changes the input source or
function.
2
3
4
When switching while viewing the display window
on the player
1. The input source switches every time the
FUNCTION is pressed.
2. Select the desired input source and press
ENTER.
When switching while viewing the TV monitor
1.Press FUNCTION to display the [Source Menu].
2. The input source switches every time the
FUNCTION is pressed. You can also use the
cursor / to switch the input source.
3. Select the desired input source and press
ENTER.
* The Source Menu screen can also be displayed
by [HOME MENU]  [Source Menu] and
pressing ENTER.
The FUNCTION button switches the input source
for the [Source Menu]. Select Home Media Gallery
to playback disc. (page 55)
5
 OPEN/CLOSE: Opens and closes the disc
tray.
• • • • • • • • • 2• • • • • • • • • TV Control Buttons: See page 53.
6
HOME MEDIA GALLERY: See page 64.
KARAOKE: Press to display the Karaoke
Settings screen.
7
RESOLUTION: Sets the output resolution for
HDMI (See page 77).
NET CONTENTS: Enhances the picture quality
of network video contents.
KEY LOCK: See page 19.
MIC VOLUME: Adjust mic volume.
DIMMER: Dims the light on the unit.
SLEEP: Sets a certain period of time after which
the unit will switch to off.
EXIT: See page 68.
Before you start
19
En
• • • • • • • • • 3• • • • • • • • • • • • • • • • • • 6• • • • • • • • • VIRTUAL 3D SOUND: Switch VIRTUAL 3D
SOUND effects (See page 75).
0-9 numerical buttons: Selects numbered
options in a menu or inputs letters in the
keypad menu.
AUDIO: See page 59.
VOL +/– : Adjusts speaker volume.
SUBTITLE: See page 58.
SOUND RETRIEVER: Switches Sound Retriever
setting (See page 75).
ANGLE: See page 58.
CD/SACD: See page 59.
 USB REC: Records an audio.
DISPLAY: Displays or exits On- Screen Display.
MUTE: Mute the unit.
• • • • • • • • • 4• • • • • • • • • TOP MENU: Press to display the top menu of
the BD-ROM or DVD-Video.
POPUP MENU/MENU: Press to display the BDROM or DVD-Video menus.
/ / / (up/ down/ left/ right): Used to navigate
on-screen displays.
ENTER: Acknowledges menu selection.
HOME MENU: Displays or exits the [Home
Menu].
RETURN: Press to return to the previous
screen.
• • • • • • • • • 5• • • • • • • • • REPLAY: Press to jump back 10 seconds when
REPLAY is pressed during playback.
TOOLS: See page 62.
CONTINUED: Use to continue playback from a
specified position.
SKIP SEARCH: Press to skip 30 seconds ahead
SKIP SEARCH is pressed during
when
playback.
//, //: See page 56.
PLAY (): Starts playback.
REV/FWD (): See page 56.
PAUSE (): Pauses playback.
STOP (): Stops playback or recording.
• • • • • • • • • 7• • • • • • • • • CLEAR: Press to clear the numeric number, etc.
REPEAT: See page 56.
A-B: See page 56.
Color buttons: Use these to navigate BD-ROM
menus.
PROGRAM: Registers FM radio stations.
BOOKMARK (RDS): Create a BOOKMARK
(See page 57). When FM TUNER is selected,
switches RDS information (See page 72).
ZOOM (PTY): Will zoom in or zoom out. When
this button is pressed while the FM tuner is
selected, the PTY value will switch.
INDEX: Slideshow playback (See page 58).
 Keylock function
You can set the keylock to prevent accidental
operations.
This function allows TVs compatible with
control function with HDMI to also perform a
Key Lock on the player.
Press and hold KEYLOCK for more than 2
seconds.
• Each time you perform this operation, the
function is activated or deactivated.
• If you try to operate the player while the
keylock function is set, LOCK lights on the
front panel display.
1
Before you start
SOUND: Switches to Sound settings (See page
75).
20
En
Before you start
Front panel
1
Before you start
2
1
3
4
9
1 Disc tray
2 Operation buttons
 (STANDBY/ON)
Switches the unit ON or OFF.
Note
If the power does not turn OFF, pressing the
 (STANDBY/ON) button for more than 5 seconds
reboots the unit and the operation becomes
possible.
 (OPEN/CLOSE)
FUNCTION
Changes the input source or function.
When switching while viewing the display
window using the button on the front panel
1. The input source switches every time the
FUNCTION is pressed.
2. Select the desired input source and press
 (PLAY/PAUSE).
The FUNCTION button switches the input
source for the [Source Menu]. Select Home
Media Gallery to playback disc. (page 55)
 (STOP)
 (SKIP)
– TUNE + (Radio tuning)
8
7
6
5
3 MIC
4 PORTABLE IN
5  (PLAY/PAUSE)
6 USB port
7 Volume control
8 Remote control sensor
Point the remote control to this, then
operate it within approximately 7 m. The
player may have trouble capturing remote
control signals if there is a fluorescent light
nearby. If this happens, move the player
away from the fluorescent light.
9 Display Window
Before you start
21
En
Rear panel
BCS-727/BCS-323
2
3
6
7 8
9 a 5 4b c
BCS-HW929/BCS-HF828/BCS-SB626/BCS-FS525
1
2
3
6
7 8
9 a 5 4b c
1 AC IN
Plug into the power source.
8 iPod
Connect to the furnished iPod cradle.
2 SPEAKERS connectors
3 Cooling Fan
9 OPTICAL IN 1/2
a HDMI OUT
4 VIDEO OUT
5 AUX IN (L/R)
b HDMI IN 1/2
c LAN port
6 ADAPTER PORT
7 Antenna Connector
Before you start
1
1
22
En
Connecting
Chapter 2
3. Mount the front/surround speaker.
Connecting
1 Insert the lower cabinet to the base so that
the cable hole is positioned at the backside.
Assemble the speakers
2
Speaker setup for BCS-727
Connecting
Preparing the speakers
1. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
2 Fix the base to the lower cabinet from the
underside, using the four screws (M4 x 16).
Caution
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Do not connect any speakers other than those
supplied to this system.
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
2. Attach the non-skid pads to the base of
each speaker.
Non-skid pads
3 Insert the upper cabinet to the lower
cabinet.
Connecting
4 Fix the upper cabinet and the lower cabinet
from the backside of the speaker using the
two screws (M4 x 12).
23
En
Wall mounting the speaker for
BCS-727
The center speaker have a mounting hole
which can be used to mount the speaker on
the wall.
Before mounting
• Do not stand on the speaker stand base of the tall
speaker to push or swing the speaker. The speaker
may fall and break, or someone may be injured.
Pay special attention to children.
Mounting screws are not supplied. Use screws
suitable for the wall material and support the
weight of the speaker.
Caution
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
5 mm
10 mm
.
Mounting screw
(not supplied)
5 mm to 7 mm
2
Connecting
Caution
• Be careful not to tighten screws excessively.
If excessive force is used to tighten screws, the
threads of screw and/or nut may be damaged. Use
a middle-sized manual screwdriver during assembly.
Do not use power screwdrivers or oversized
screwdrivers that may exert excessive force on the
screws and nuts. Confirm that no foreign matter
is stuck to the base or the lower cabinet during
assembly. If the unit is assembled with foreign matter
stuck between the base and lower cabinet, the unit
may not be assembled securely, resulting in tipping
or falling.
Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speakers on is strong enough to support
them. Do not mount on plywood or soft surface
walls.
A
C
A
A
A
A
24
Connecting
En
F
D
F
A
A
A
A
G B
F
C
C
B
A
A
C
D G
G A
B
A
A
A
A
A
A
Additional
notes onGspeaker
A
F
D
A
for BCS-727
A
A
A
A
A
Precautions:
A
2
A
A
A
AB
C
Connecting
G with this system
The center speaker supplied
F
A
are magnetically
shielded.
However, depending
A
A B
D
on the installation location,AcolorA distortion
A
A B C
A
may occur if the speaker is installed extremely
close to the screen of a television set. If this
case happens, turn the power switch of the A
A B C D
television set OFF, and turn it ONAafter
15 min.
to 30 min. If the problem persists, place the
speaker system away
from the television set.
A
C
D
E
D
The subwoofer is not magnetically shielded and
so should not be placed near a TV or monitor.
Magnetic storage media (such as floppy discs
B
and tape or video
cassettes) should also not be
kept close to the subwoofer. A A B C D E
E
B C left
E F (L)/
G
Front
E D speaker
A
B Front
C E D right
E speaker
F G
(R):
A
Place
the front speakers to
A
the sides of the
monitor or screen and as flush with the screen
surface as possible.
A
Install the main front left and right speakers at
A B
an equal distance from Dthe TV.
D
E
E
F
E
D E speaker:
F G
Center
Place the center speaker below or in front of
the monitor or screen.
C
E F G left speaker (L)/
Surround
F G
Surround
right speaker (R):
Place these speakers behind your listening
Eposition, facing slightly inwards.
D
E
F Subwoofer:
G
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it
slightly toward the center of the room to reduce
the wall reflections.
G
Unit
C
attach
Do not
the front/surround speakers and
G to a wall or ceiling. They may fall off
subwoofer
and cause injury.
A
F
A
A
Positioning the system for
E
BCS-727
A
A
D
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from
A
the actual unit for explanation purposes. For
the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position ( A ). A B C D E F G
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• Place the centre speaker at a safe distance from
the child’s reach.
Otherwise it may result in the speaker falling
down and causing personal injury and/or property
damage.
• The speakers contain magnet parts, so color
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
Connecting
Speaker setup for BCS-323
Preparing the speakers
1. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
25
En
Wall mounting the speaker for
BCS-323
All speakers have a mounting hole which can
be used to mount the speaker on the wall.
Before mounting
Mounting screws are not supplied. Use screws
suitable for the wall material and support the
weight of the speaker.
Caution
Caution
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
• Do not connect any speakers other than those
supplied to this system.
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
2. Attach the non-skid pads to the base of
each speaker.
Mounting screw
(not supplied)
5 mm
10 mm
5 mm to 7 mm
Non-skid pads
This hole is used to fix the
unit to the speaker stand.
Caution: Do not use this hole
to mount on walls or ceilings.
The speaker may fall resulting
in injury.
2
Connecting
Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speakers on is strong enough to support
them. Do not mount on plywood or soft surface
walls.
A
C
A
A
A
26
En
A
Connecting
F
D
F
A
A
C
C
B
A
A
C
D G
G A
B
A
A
A
A
A
A
A
A
A
Precautions:
2
A
A
A
AB
C
Connecting
TheA center speaker supplied
G with this system
F
are magnetically
shielded.
However, depending
A
A
A B
D
on the installation location,AcolorA distortion
A
A B C
A
may occur if the speaker is installed extremely
close to the screen of a television set. If this
case happens, turn the power switch of the A
A 15
B min.
C D
television set OFF, and turn it ONAafter
to 30 min. If the problem persists, place the
speaker system away from the television set.
C
D
E
A
The subwooferD is not magnetically shielded and
so should not be placed near a TV or monitor.
B
Magnetic storage
media (such as floppy discs
and tape or video cassettes) should also not be
A B C D E
kept close
C to the subwoofer. A
A
G
Do not attach
the subwoofer to a wall or
ceiling. They may fall off and cause injury.
F
A
A
Positioning the system for
E
BCS-323
A
A
D
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from
A
the actual unit for explanation purposes. For
the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position ( A ). A B C D E F G
E
B C left
E F (L)/
G
Front
E D speaker
A
B Front
C E D right
E speaker
F G
(R):
A
Place
the front speakers to
A
the sides of the
monitor or screen and as flush with the screen
surface as possible.
A
Install the main front left and right speakers at
A B
an equal distance from Dthe TV.
D
E
E
A
Additional
notes onGspeaker
A
F
D
for BCS-323
A
A
A
A
G B
F
F
E
D E speaker:
F G
Center
Place the center speaker below or in front of
the monitor or screen.
C
E F G left speaker (L)/
Surround
F G
Surround
right speaker (R):
Place these speakers behind your listening
Eposition, facing slightly inwards.
D
E
F Subwoofer:
G
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it
slightly toward the center of the room to reduce
the wall reflections.
G
Unit
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• Place the centre speaker at a safe distance from
the child’s reach.
Otherwise it may result in the speaker falling
down and causing personal injury and/or property
damage.
• The speakers contain magnet parts, so color
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
Connecting
Speaker setup for BCS-HW929
Preparing the speakers
27
En
2. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
1. Attach the non-skid pads to the base of
each speaker.
For front speaker:
Use the supplied adhesive to attach six
pads to the base (bottom) of speaker.
2
Connecting
Non-skid pad
(for front)
Affix to
three locations
Caution
• Do not connect any speakers other than those
supplied to this system.
Non-skid pad
(for front)
For subwoofer:
Use the supplied adhesive to attach four
large pads to the base of subwoofer.
Large non-skid pads
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
• Please connect the speaker cable of subwoofer
(purple) to orange of the player.
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
28
En
Connecting
Wall mounting the speaker for
BCS-HW929
3. Using the two screws removed in step 1,
fasten the wall mounting fixtures to the
speaker.
Before mounting
2
Connecting
• Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speaker on is strong enough to support
them. Do not mount on plywood or soft
surface walls.
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
Caution
4. Affix the supplied wire stays to the top of the
unit as shown and collect the cable there.
Press until a “click” is
heard.
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
1. Remove the base plates.
The base plates are held in position by the
use of 2-sided tape. While holding the leg in
place, strongly press the base plate in the
direction indicated by the arrow to remove
the base plate. Be careful not to damage
the front speaker while doing this.
Base plate
5. Mount on wall.
Wall
mounting
screws
(available
commercially)*
Leg
6 mm to 8 mm
2. Use a Phillips screwdriver to remove the
two screws holding the legs to the speaker.
* Wall mounting screws are not included. Purchase
appropriate screws taking into consideration the
type of wall and the weight of the speaker system.
Open two holes in the wall 818 mm apart.
B
C
A
C
F
A
AG
D
F
A
A
G
A
A
A
Connecting
A
Additional notes on speaker
for BCS-HW929
B
C
D E
Unit
B
C
D
E F G position
Listening
The front speaker and subwoofer are not
magnetically shielded and so should not be
placed near a TV or monitor. Magnetic storage
media (such as floppy discs and tape or video
cassettes) should also not be kept close to the
front speaker and subwoofer.
Do not attach the subwoofer to a wall or
ceiling. They may fall off and cause injury.
Positioning the system for
BCS-HW929
B
C
G
B
A
A
A
C
E
A
D
D
Pioneer logo
A
A
A
B C speaker
D E
Front
F
G
The front speaker should be installed so as to
reflect sound off the television screen, thus
producing the Sound Wing’s characteristic
breadth of sound. When installing the speaker,
orient the unit so that front speaker’s top
edge is pointed up, then bring it closer to the
television screen so that the Pioneer logo
is oriented as shown in the accompanying
illustration.
B
F
G
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• The speakers contain magnetic parts, so colour
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
• Do not stand on the speaker, nor hang it from
another object, since it may fall or be otherwise
damaged. Be especially careful if infants are
present, and do not allow them to hold to or lean
on the unit.
2
Connecting
Make sure that all the bare speaker wire is A
twisted together and inserted fully into the
A
A
speaker terminal. If any of the bare speaker
wire touches the back panel it may cause the
power to cut off as a safety measure.
A
A
Precautions:
En
C D EE F G
Subwoofer:
TheAposition of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place
the subwoofer near the front speaker. Turn it
slightly toward the center of the room to reduce
the wall reflections.
A
A
29
E
A
D
Install the front speaker below
the TV, in the
A
center position.
D
A
E
A
B
30
En
Connecting
Speaker setup for BCS-HF828
Preparing the speakers
2. Fasten the speaker to the base use the
horizontal mounting screw from the back
side of the base.
For subwoofer:
Use the supplied adhesive to attach four large
pads to the base of subwoofer.
2
Horizontal mount
screw
Connecting
Large non-skid pads
For vertical installation
Caution
For front speakers:
Assembling the speaker stands and securing
your front speakers.
For horizontal installation:
Caution
1. Align the vertical mounting stay with the
hole in the base.
2. Fasten the vertical mount stay to the base
using the vertical mount bolt and hex nut.
Be sure the hex nut fits into the hexagonal
groove in the bottom of the base.
Vertical mount screw
1. Align the rotation stop lug with the hole in
the base.
Rotation stop
lug
Vertical mount
hexnut
Connecting
3. Affix the seal on the screw head.
31
En
Caution
• Do not connect any speakers other than those
supplied to this system.
Seal
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
• Please connect the speaker cable of subwoofer
(purple) to orange of the player.
Rotation
stop lug
5. Fasten the speaker to the vertical stay, using
the vertical mount screw.
Vertical mount screw
6. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
2
Connecting
4. Align the speaker’s rotation stop lug with
the hole in the vertical stay.
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
32
En
Connecting
Wall mounting the speakers
for BCS-HF828
2. Attach to wall.
Before mounting
2
Connecting
• Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speakers on is strong enough to support
them. Do not mount on plywood or soft
surface walls.
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
Caution
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
Wall mounting
screws
(available
commercially)*
6 mm to 8 mm
* Wall mounting screws are not included.
Purchase appropriate screws taking into
consideration the type of wall and the
weight of the speaker system.
Open two holes in the wall 95 mm apart.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
1. Use the vertical mounting screw to fasten
the wall mounting fixture to the speaker
system.
When mounting the unit on speaker stand
Use the accessory bracket when mounting the
unit on any speaker stand or base other than
those provided.
Use M5 screws for installation. Mounting
screws are not provided.
Follow the instructions accompanying your
selected speaker stand or base.
B
C
A
Connecting
G
F
33
En
A
A
A
Positioning the system for
E
BCS-HF828
A
Install the main front left and right speakers at
equal distance from the TV.
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from
A
the actual unit for explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position ( A ). A B C D E F G
D
Precautions:
Make sure that all the bare speaker wire is
twisted together and inserted fully into the
speaker terminal. If any of the bare speaker
wire touches the back panel it may cause the
power to cut off as a safety measure.
B
B
C
The front speakers and subwoofer are not
A
magnetically shielded and so should not beC BG
F
placed near a TV or Amonitor. Magnetic
storage
G
media (such as floppy discsF and tape or Cvideo A
A
A
cassettes) should
A also not be kept close to the
A
G
A
front speakers and subwoofer.
F
Do not attach the subwoofer to a wall orA
A
ceiling. They may fall off and cause
injury.
D
AC
D
A
A
AG
D
F
A
A
D
A
D
A
A
A
B
E
A
A
E
E
E
A
A
A
A
A
A
A
B C left
D speaker
E F (L)/
G
Front
A
C D right
E speaker
F G
Front
(R):
Can be mounted
vertically or horizontally.
E
A
B
D EE F G
Subwoofer:
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it
slightly toward the center of the room to reduce
the wall reflections.
A
A
A
A
A
D
C
G
C
F
A
B
B
A
B
C
A
A
A
A
B
C
D
E F
Unit
A
B
C
D
E
F G
Listening
position
G
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• The speakers contain magnetic parts, so colour
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
2
Connecting
Additional notes on speaker
for BCS-HF828
34
En
Connecting
Speaker setup for BCS-SB626
2. Attach the speaker stand bases to the
speaker.
Preparing the speakers
For subwoofer:
Use the supplied adhesive to attach four large
pads to the base of subwoofer.
2
Attach both right and left speaker stands
to the rear of the speaker. The height of
the speaker stands can be adjusted in two
levels; select the height you prefer, and fix in
position
Connecting
Large non-skid pads
Caution
For front speaker:
Assembling the speaker stands and securing
your front speaker.
1. Use the supplied adhesive to attach three
small pads to the base (bottom) of each
speaker stand.
• Be careful not to tighten screws excessively.
• If excessive force is used to tighten screws, the
threads of screw may be damaged. Use a middlesized manual screwdriver during assembly.
• Do not use power screwdrivers or oversized
screwdrivers that may exert excessive force on the
screws.
• Confirm that no foreign matter is stuck to the stand
or the speaker during assembly.
Small non-skid pads
If you decide not to use the speaker stands,
use the supplied adhesive to attach four small
pads to the base of the speaker.
Small non-skid pads
• If the unit is assembled with foreign matter stuck
between the stand and the speaker the unit may
not be assembled securely, resulting in tipping or
falling.
Connecting
3. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
35
En
Wall mounting the speaker for
BCS-SB626
The speaker have the mounting holes which
can be used to mount the speaker on the wall.
Before mounting
Caution
• Do not connect any speakers other than those
supplied to this system.
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
• Please connect the speaker cable of subwoofer
(purple) to orange of the player.
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
Caution
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
• When mounting the speaker on a wall, install it so
that it is parallel to the floor.
• When mounting the speaker on a wall, do not
attach the accessory speaker stands.
Mounting screw
(not supplied)
4 mm to 5 mm
2
Connecting
• Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speaker on is strong enough to support
them. Do not mount on plywood or soft
surface walls.
36
En
Connecting
Additional notes on speaker
placement for BCS-SB626
Positioning the system for
BCS-SB626
B
Install the speaker below the TV, in the center
position.
Precautions:
2
A
G
C
F
A
C
B
G
Do not rest the speaker on Fthe TV itself.
B
A
A
Connecting
A
Make sure that all the bare speaker wire
is A
A
twisted together and inserted fully into
the
speaker terminal. If any of the bare speaker B
wire touches the back panel it may cause the
B
power to cut off as a safety measure.
C
A
A
C
A
A
E
E
D
A and subwoofer are not
The front speaker
A
D C G
magneticallyAshielded and
F so should not be
AG
D
A
placed near a TV or monitor.
Magnetic
storage
A
F
media (such as floppy discs andAtape or video
A
A
cassettes) should also not beAkept close to the
front speaker and subwoofer.
A
A
A
A
A
B
C
D E
Unit
A
B
C
D
E F G position
Listening
Do not attach the subwoofer to a wall or
ceiling. They may fall off and cause injury.
A
D
D
A
A
A
B C speaker
D EE
Front
A
F
G
C D EE F G
Subwoofer:
TheAposition of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place
the subwoofer near the front speaker. Turn it
slightly toward the center of the room to reduce
the wall reflections.
B
F
G
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• The speakers contain magnet parts, so colour
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
Connecting
Speaker setup for BCS-FS525
37
En
3. Pass the speaker wire through the hole on
the pole.
Preparing the speakers
For subwoofer:
Use the supplied adhesive to attach four large
pads to the base of subwoofer.
2
4. Secure the speaker and the pole with 2
screws. Ensure that the speaker wire does
not get pinched between the speaker and
the pole.
For front speakers:
Assembling the speaker stands and securing
your front speakers.
For vertical installation
1. Use the supplied adhesive to attach 4 small
pads to the speaker stand base.
Small non-skid pads
For horizontal installation
1. Use the supplied adhesive to attach 4 small
pads to the speaker stand base.
Small non-skid pads
2. Insert the large pole from the holes behind
the base and secure with the 4 screws.
2. Insert the small pole from the holes behind
the base and secure with the 4 screws.
Connecting
Large non-skid pads
38
En
Connecting
3. Secure the speaker and the pole with 2
screws. Ensure that the speaker wire does
not get pinched between the speaker and
the pole. The height of the speaker stands
can be adjusted in two levels; select the
height you prefer, and fix in position.
For direct installation
Use the supplied adhesive to attach 4 pads to
the base of the front speakers.
2
Connecting
Caution
4. Connect the wires to the player.
Insert the cables connected to the player to
the same colored connector on the speaker.
• Do not connect any speakers other than those
supplied to this system.
• Do not connect the supplied speakers to any
amplifier other than the one supplied with this
system. Connection to any other amplifier may
result in malfunction or fire.
• Please connect the speaker cable of subwoofer
(purple) to orange of the player.
• These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Connecting
Wall mounting the speakers
for BCS-FS525
Before mounting
En
Attaching the speakers
The front speaker can be hung vertically or
horizontally on the wall. Use one hole to hang it
vertically and two holes to hang it horizontally.
The illustration below shows the front right
speaker.
Vertical set up
Hole
2
Connecting
• Remember that the speaker system is heavy
and that its weight could cause the screws
to work loose, or the wall material to fail to
support it, resulting in the speaker falling.
Make sure that the wall you intend to mount
the speakers on is strong enough to support
them. Do not mount on plywood or soft
surface walls.
39
110
Horizontal set up
• Mounting screws are not supplied. Use
screws suitable for the wall material and
support the weight of the speaker.
Hole
Caution
• If you are unsure of the qualities and strength of
the wall, consult a professional for advice.
• Pioneer is not responsible for any accidents or
damage that result from improper installation.
When installing the speaker horizontally, set
it up so that the speaker wire position on the
back side of the speaker is on the outside on
the end of the surface, farthest away from the
other speaker.
Speaker wire position
Mounting screw
(not supplied)
5 mm to 7 mm
Front right
Speaker wire position
Front left
B
40
En
C
A
Connecting
G
F
Additional notes on speaker
placement for BCS-FS525
Positioning the system for
E
BCS-FS525
A
Install the main front left and right speakers at
an equal distance from the TV.
The following illustration shows an example
of positioning the system. Note that the
illustrations in these instructions differ from
A
the actual unit for explanation purposes.
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed
at the same distance from the listening
B
position ( A ). A B C D E F G
D
Precautions:
2
A
A
A
Connecting
Make sure that all the bare speaker wire is
twisted together and inserted fully into the
speaker terminal. If any of the bare speaker
wire touches the back panel it may cause the
power to cut off as a safety measure.
C
A
B
The front speakers and subwoofer is not
C G
F
A and so should
magnetically shielded
not be G
F Magnetic storage A
placed near a TV or monitor.
B
A
A
media (such as floppy discs and tape or video
A
A
cassettes) should also not be kept close
to the
C
front speakers and
A subwoofer.
B
A
D
A
G
F
Do not attach the subwoofer
to a wall or
ceiling. They may fall off and cause injury.
A
A
A
E
EA
A
A
A
D
A
D
C
A
B
E
A
C
A
G
F
A
D
A
A
D
C D right
E speaker
F G
Front
(R):
Place the front speakers to the sides of the
monitor or screen and as flush with the screen
surface asE possible.
A
A
B
D E F G
Subwoofer:
The position of the subwoofer is not so
critical, because low bass sounds are not
highly directional. But it is better to place the
subwoofer near the front speakers. Turn it
slightly toward the center of the room to reduce
the wall reflections.
A
B
C
A
A
B C left
D speaker
E F (L)/
G
Front
A
A
A
A
A
B
C
D
A
E F
Unit
G
Caution
• Be careful to make sure children do not put their
hands or any objects into the *subwoofer duct.
*subwoofer duct: A hole for plentiful bass sound
on subwoofer cabinet (enclosure).
• The speakers contain magnetic parts, so colour
irregularity may occur on the TV screen (CRT) or
PC monitor screen. Please use the speakers away
from the TV screen (CRT) or PC monitor screen.
Connecting
Connecting to Your TV
Make one of the following connections,
depending on the capabilities of your existing
equipment.
• HDMI connection (page 41)
41
En
HDMI connection
If you have a HDMI TV or monitor, you can
connect it to this player using a HDMI cable
(High Speed HDMI®/™ Cable). Connect the
HDMI terminal on the player to the HDMI
terminal on a HDMI compatible TV or monitor.
• Video connection (page 42)
Note
• Please refer to the manuals of your TV, stereo
system or other devices as necessary to make the
best connections.
• Make sure the player is connected directly to the
TV. Tune the TV to the correct video input channel.
• Do not connect your player via your VCR. The
image could be distorted by the copy protection
system.
HDMI
cable
TV
Set the TV’s source to HDMI (refer to TV’s
Operating Instructions).
Caution
Connecting the player and the TV using the
HDMI cable alone does not enable you to hear
the audio from the devise. Please also connect
by either the optical cable (page 44) or the
analog audio cable (page 43).
When connected to a DVI device
• It is not possible to connect DVI devices
(computer displays, for example) that are
not compatible with HDCP. HDCP is a
specification to protect audiovisual content
across the DVI/HDMI interface.
• No audio signals are output. Connect using
an audio cable, etc.
• This player is designed for connection with
HDMI compatible devices. When connected
to a DVI device, it may not operate properly
depending on the DVI device.
2
Connecting
Rear of the unit
• Depending on your TV and other equipment you
wish to connect, there are various ways you could
connect the player. Use only one of the connections
described in this manual.
42
En
Connecting
ARC (Audio Return Channel)
function
The ARC function enables an HDMI capable TV
to send the audio stream to HDMI OUT of this
player.
Video connection
Connect the VIDEO OUT terminal on the player
to the video in terminal on the TV using a video
cable. You can hear the sound through the
system’s speakers.
To use this function:
2
-- Your TV must support the ARC function.
Connecting
-- The setting method of ARC may differ
depending on the TV. For details about ARC
function, refer to your TV manual.
Rear of the unit
-- You must use the HDMI cable (High Speed
HDMI®/™ Cable).
-- You must connect with the HDMI IN of TV
that supports the ARC function using the
HDMI OUT on this player.
-- You can connect only one Home Theater to
TV compatible with ARC.
Video cable
-- The ARC function does not warrant that the
function works in all cases even if the above
conditions are satisfied.
-- When you use the ARC function, CEC
(Consumer Electronics Control) may work.
If you do not want to use CEC, you can stop
it work by setting [Control: Off] on HDMI. In
this case, it is needed to connect TV and this
player by an optical cable to send the audio
stream to this player.
-- Power on the unit when using CEC function.
-- CEC does not operate during Standby mode.
TV
Connecting
Antenna connection
Connect the supplied antenna for listening to
the radio.
43
En
Connections with
external device
AUX connection
You can enjoy the sound from an external
component through the speakers of this
system.
Rear of the unit
Rear of the unit
Note
• After connecting the FM wire antenna, keep it as
horizontal as possible. Be sure to fully extend the
FM wire antenna.
White
Red
To the audio output
terminals of your
component
(TV, VCR, etc.)
2
Connecting
Connect the analog audio output terminals of
your component into the AUX L/R (INPUT) on
this unit. And then select the [AUX] option by
pressing FUNCTION and ENTER.
44
En
2
Connecting
PORTABLE IN connection
OPTICAL IN 1/2 connection
You can enjoy the sound from your portable
audio player through the speakers of this
system.
You can enjoy the sound from your component
with a digital optical connection through the
speakers of this system.
Connect the headphones (or line out ) terminal
of the portable audio player into the PORTABLE
IN socket of this unit. And then select the
[Portable In] option by pressing FUNCTION and
ENTER.
Connect the optical output terminal of your
component into the OPTICAL IN 1 or 2 terminal
on the unit. And then select the [Optical IN 1/2]
option by pressing FUNCTION and ENTER.
Connecting
Rear of the unit
To the digital optical
output terminal of
your component
MP3 Player, etc...
Note
• When inserting the PORTABLE IN terminal, support
the top of the unit with your hand to prevent it from
moving.
Connecting
HDMI IN 1/2 connection
You can enjoy the pictures and sound from
your component through this connection.
Connect the HDMI OUT terminal of your
component into the HDMI IN 1 or 2 terminal
on this unit. And then select the [HDMI IN 1/2]
option by pressing FUNCTION and ENTER.
Rear of the unit
45
En
Connecting optional
Bluetooth® ADAPTER
When the Bluetooth ADAPTER (Pioneer Model
No. AS-BT100 or AS-BT200) is connected to
this unit, a product equipped with Bluetooth
wireless technology (portable cell phone,
digital music player, etc.) can be used to listen
to music wirelessly.
*For instructions on playing the Bluetooth
wireless technology device, see Pairing the
Bluetooth ADAPTER and Bluetooth wireless
technology device on page 73.
To the HDMI OUT
terminal of your
component
(set-top box, digital
satellite receiver,
video game
machine, etc.)
Rear of the unit
Note
• You cannot change the video resolution in the
HDMI IN 1/2 mode. Change the video resolution of
the connected component.
• If the video output signal is abnormal when your
personal computer is connected to HDMI IN 1/2
terminal, change the resolution of your personal
computer to 576p, 720p, 1080i or 1080p.
• The video signal from the HDMI input cannot be
output from the component or composite video
outputs.
• You may not able to output 3D images depending
on the type of the 3D output signal of the
connected device.
Bluetooth® ADAPTER
Note
• Do not move the unit while the Bluetooth ADAPTER
is connected. Doing so could cause damage or
faulty contact.
2
Connecting
Connect a Bluetooth ADAPTER to the
ADAPTER PORT terminal on the rear panel.
46
En
Connecting
Connecting to your
Home Network
2
Connecting
This player can be connected to a local area
network (LAN) via the LAN port on the rear
panel or the internal wireless module.
By connecting the unit to a broadband home
network, you have access to services such
as BD-LIVE interactivity and Online content
services.
Broadband
service
Router
Wired network connection
Using a wired network provides the best
performance, because the attached devices
connect directly to the network and are not
subject to radio frequency interference.
Please refer to the documentation for your
network device for further instructions.
Connect the player’s LAN port to the
corresponding port on your Modem or Router
using a commercially available LAN or Ethernet
cable.
PC and/or DLNA certified server
Note
• When plugging or unplugging the LAN cable, hold
the plug portion of the cable. When unplugging,
do not pull on the LAN cable but unplug while
pressing down on the lock.
• Do not connect a modular phone cable to the LAN
port.
• Since there are various connection configurations,
please follow the specifications of your
telecommunication carrier or internet service
provider.
• If you want to access content from PCs or DLNA
servers, this player must be connected to the same
local area network with them via a router.
Rear of the unit
Connecting
47
En
Wireless network connection
Wireless network setup
Another connection option is to use an
Access Point or a wireless router. The network
configuration and connection method may vary
depending on the equipment in use and the
network environment.
For the wireless network connection, the player
needs to be set up for network communication.
This adjustment can be done from the [Setup]
menu. Adjust the [NETWORK] setting as follow.
Setting up the access point or the wireless
router is required before connecting the player
to the network.
Preparation
Before setting the wireless network, you need
to:
-- connect the broadband internet to the
wireless home network.
-- set the access point or wireless router.
-- note the SSID and security code of the
network.
Wireless
Communication
1.Select [Initial Setup]  [Network] 
[Interface]  [Wireless] and press ENTER.
PC and/or
DLNA certified server
Access Point or
Wireless Router
Broadband
service
Refer to the setup instructions supplied with
your access point or wireless router for detailed
connection steps and network settings.
For best performance, a direct wired connection
from this player to your home network’s router
or cable/DSL modem is always the best option.
If you do chose to use the wireless option, note
that performance can sometimes be affected
by other electronic devices in the home.
2.Select [Initial Setup]  [Network] 
[Wireless Setting]  [Next Screen] and
press ENTER.
3.Select [Yes] and press ENTER to continue.
The new connection settings reset the
current network settings.
4. [Wireless Setting] menu is displayed.
Use / to select [Scan]. Then select [Next]
using the / and press ENTER.
5. The player scans the all available access
points or wireless routers within range and
display them as a list. Use / to select an
access point or wireless router on the list,
and then press ENTER.
If you have security on your access point
or wireless router, verify that the WEP or
WPA key that was entered into the player
matches the router’s information exactly.
You need to input the security code as
necessary.
6. How to enter the security code.
1 Select the security code section using
/ / / and press ENTER to start the
software keyboard.
2Use / / / to select characters and
items, and then press ENTER to input.
3Select [abc], [ABC], or [!@#$] using /
/ / to switch to lower case characters,
upper case characters, or symbols.
2
Connecting
This player is equipped with an IEEE 802.11n
(Single band, 2.4 GHz band) wireless module,
which also supports the 802.11b/g standards.
For the best wireless performance, we
recommend using a IEEE 802.11n certified WiFi network (access point or wireless router).
48
En
Connecting
4 Finish entering the security code by
selecting [Enter] using / / / and
pressing ENTER.
7.Select [Next] using / / / and press
ENTER. If it connects success, it will display
connection success and IP is obtained.
8.Pressing ENTER ends [Wireless Setting].
2
Note
Connecting
yy WEP security mode generally have 4 keys
available on an access point or wireless
router’s setting. If your access point or wireless
router use WEP security, enter the security
code of the key “No.1” to connect on your home
network.
yy An Access Point is a device that allows you to
connect to your home network wirelessly.
[Scan] – The player scans the all available
access points or wireless routers within
range and display them as a list.
[Manual] – Your access point may not
be broadcasting its access point name
(SSID). Check your router settings through
your computer and either set your router
to broadcast SSID, or manually enter the
access point name (SSID) in [Manual].
[Auto] – If your access point or wireless
router that supports the Push Button
Configuration method, select this option
and press the Push Button on your access
point or wireless router within 120 counts.
You do not need to know the access point
name (SSID) and security code of your
access point or wireless router.
Note
yy If there is no DHCP server on the network and
you want to set the IP address manually, Please
refer to “Setting the IP address”. (Page 80)
Connecting
WPS setup
(Wi-Fi Protected Setup)
WPS connection setting
This unit supports push-button configuration
and PIN code configuration.
PBC (Push Button Configuration)
Connection settings are made automatically
simply by pressing the WPS buttons on the
WPS compatible wireless LAN device. This is
the simplest way of making the settings, and
is possible when the WPS compatible wireless
LAN device is equipped with WPS button.
PIN Input
Connection settings are made by inputting the
8-digit PIN code shown on the main display to
the access point to which you selected. Follow
the instructions shown in Connecting using
PIN code configuration on the right.
When performing wireless settings set [Initial
Setup]  [Network]  [Interface] to [Wireless].
1. Press HOME MENU.
The HOME MENU screen is displayed.
2. Use cursor buttons to select [Initial
Setup] and press ENTER.
The Initial Setup screen is displayed.
3. Select [Initial Setup]  [Network] 
[Wireless Setting]  [Next Screen] and
press ENTER.
A confirmation screen is displayed.
4.Use / to select Yes, then press
ENTER.
The Wireless Setting screen is displayed.
5.Use / to select Auto, then press
ENTER.
The WPS (Wi-Fi Protected Setup) screen is
displayed.
6.Use / to switch between [PBC] or
[PIN] screens.
When connecting using PBC go to step 7.
When connecting using PIN go to step 8.
En
7. When connecting using PBC (Push
Button), on the [PBC] screen use /
to select NEXT, then press ENTER.
Then press the WPS button on the access
point within 120 seconds.
8. When connecting using PIN confirm
the PIN Code on the [PIN] screen. Use
cursor / to select NEXT, then press
ENTER.
9. Enter into the access point the PIN
Code that you confirmed in step 8
above.
The PIN Code input method differs
depending on the LAN device used. For
details, consult the operating instructions
accompanying your LAN device.
Notes on Network Connection:
• Many network connection problems during
set up can often be fixed by re-setting the
router or modem. After connecting the player
to the home network, quickly power off and/
or disconnect the power cord of the home
network router or cable modem. Then power
on and/or connect the power cord again.
• Depending on the internet service provider
(ISP), the number of devices that can
receive internet service may be limited by
the applicable terms of service. For details,
contact your ISP.
• Our company is not responsible for any
malfunction of the player and/or the internet
connection feature due to communication
errors/malfunctions associated with your
broadband internet connection, or other
connected equipment.
• The features of BD-ROM discs made
available through the Internet Connection
feature are not created or provided by
our company, and our company is not
responsible for their functionality or
continued availability. Some disc related
material available by the Internet Connection
may not be compatible with this player. If you
have questions about such content, please
contact the producer of the disc.
2
Connecting
WPS is abbreviation of Wi-Fi Protected Setup.
A standard established by the Wi-Fi Alliance
industry group for a function allowing settings
related to interconnection of WPS compatible
wireless LAN devices and encryption to be
made with simple operations.
49
50
En
Connecting
• Some internet contents may require a higher
bandwidth connection.
• Even if the player is properly connected and
configured, some internet contents may
not operate properly because of internet
congestion, the quality or bandwidth of your
internet service, or problems at the provider
of the content.
2
Connecting
• Some internet connection operations may not
be possible due to certain restrictions set by
the Internet service provider (ISP) supplying
your broadband Internet connection.
• Any fees charged by an ISP including,
without limitation, connection charges are
your responsibility.
• A 10 Base-T or 100 Base-TX LAN port is
required for wired connection to this player.
If your internet service does not allow for
such a connection, you will not be able to
connect the player.
• You must use a Router to use xDSL service.
• xDSL modem is required to use xDSL service
and a cable modem is required to use cable
modem service. Depending on the access
method of and subscriber agreement with
your ISP, you may not be able to use the
internet connection feature contained in this
player or you may be limited to the number
of devices you can connect at the same time.
(If your ISP limits subscription to one device,
this player may not be allowed to connect
when a PC is already connected.)
• The use of a “Router” may not be allowed
or its usage may be limited depending on
the policies and restrictions of your ISP. For
details, contact your ISP directly.
• The wireless network operate at 2.4 GHz
radio frequencies that are also used by
other household devices such as cordless
telephone, Bluetooth® devices, microwave
oven, and can be affected by interference
from them.
• Turn off all unused network equipment in
your local home network. Some devices may
generate network traffic.
• For the purpose of the better transmission,
placing the player from the access point as
close as possible.
• In some instances, placing the access point
or wireless router at least 0.45 m above the
floor may improve the reception.
• Move closer to the access point if possible
or re-orient the player so there is nothing
between it and the access point.
• The reception quality over wireless depends
on many factors such as type of the access
point, distance between the player and
access point, and the location of the player.
• Set your access point or wireless router to
Infrastructure mode. Ad-hoc mode is not
supported.
Connecting
51
En
USB device connection
This player can play movie, music and photo
files contained in the USB device.
About USB devices
1. Insert a USB device to the USB port until it
fits into place.
The USB devices that can be connected to the
player are as shown below.
• USB 2.0-compatible memory devices
• FAT16 or FAT32 file system, minimum 1 GB
capacity (2 GB or more recommended)
2
Connecting
Note
• Devices formatted with a file system other than the
above cannot be used.
• USB devices may not be recognized if they contain
multiple partitions.
• Some USB devices may not operate with this
player.
• Operation of USB devices is not guaranteed.
Connecting the USB device
Caution
• Be sure to turn the player’s power off before
connecting or disconnecting USB devices.
• Use empty USB devices (on which nothing is
stored).
• When using an external hard disk as the external
storage device, be sure to turn on the hard disk’s
power before turning on the player’s power.
• If the USB device is write-protected, be sure to
disable the write-protection.
• When connecting the USB cable, hold onto the
plug, set the plug in the proper direction for the
port and insert it horizontally.
• Placing excessive loads on the plug may result in
poor contact, making it impossible to write data on
the USB device.
• When a USB device is connected and the player’s
power is turned on, do not unplug the power cord.
• USB Port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
• If more than one USB device is connected, the
number displayed for the USB device may change
depending on the type of device connected or
circumstance. To confirm USB device number, go
to [HOME MENU]  [Home Media Gallery].
Note
• Devices may not work if connected to the USB port
via a memory card reader or USB hub.
• Use a USB cable with a length of 2 meters or less.
• When inserting the USB terminal, support the
top of the unit with your hand to prevent it from
moving.
52
En
Getting Started
Capter 3
Getting Started
Making settings using
the Setup Navigator
menu
Be sure to perform these settings when using
the player in the following situations.
• When you use the player for the first time.
3
• After Initial Setup format.
Getting Started
• After updating the player’s software.
Caution
• Before turning on the power, check that the
connections between the player and other devices
are correct. Also, turn on the power of the devices
connected to the player before turning on the
player’s power.
• When using a Pioneer Flat Screen TV or front
projector compatible with the Control function,
set Control to On on the connected device before
turning on the player’s power.
Note
• When a Pioneer Flat Screen TV or front projector
compatible with the Control function is connected
to the player using an HDMI cable, the player is
automatically set to the optimum picture quality for
the connected device.
1. Turn on the TV’s power and switch the
input.
See the TV’s operating instructions for the
details of operating the TV.
2. Turn on the player’s power.
Press  STANDBY/ON.
Check that the Setup Navigator menu is
displayed.
If the Setup Navigator menu is not
displayed
HOME MENU to display the
 Press
Home Menu, select Initial Setup  Setup
Navigator  Start, then press ENTER.
3. Start Setup Navigator.
Press ENTER.
yy Setup Navigator starts.
4. Select the OSD language.
Use / to select, then press ENTER.
When a Pioneer Flat Screen TV that
is compatible with Control function is
connected to this player’s HDMI OUT
terminal, language settings are imported
from the Pioneer Flat Screen TV’s language
settings before Setup Navigator begins.
5. Select the appropriate output resolution
for the connected TV.
Use / to select, then press ENTER.
6. Select the appropriate aspect for the
connected TV.
Use / to select, then press ENTER.
7. Close the Setup Navigator menu.
Press ENTER.
yy Setup Navigator finishes and the setting
is stored.
RETURN to go back to the
yy Press
previous screen.
Getting Started
53
En
Operating the TV with
the player’s remote
control
When the manufacturer code for your brand
of TV is set on the player’s remote control, the
TV can be operated using the player’s remote
control.
Caution
• For some models it may not be possible to operate
the TV with the player’s remote control, even for
TVs of brands listed on the manufacturer code list.
3
1. Input the 2-digit manufacturer code.
Press the number buttons (0 to 9) to input
the code while pressing TV CONTROL u.
Note
yy The factory default setting is 00 (PIONEER).
yy If you make a mistake when inputting the code,
release TV CONTROL u then start over from the
beginning.
yy When there are multiple codes for a
manufacturer, try inputting them in the
indicated order until the TV can be operated.
2. Check that the TV can be operated.
Operate the TV using TV CONTROL.
u – Press to turn the TV’s power on and off.
INPUT SELECT – Press to switch the TV’s
input.
CH +/– –Press to select the TV channel.
VOL +/– –Press to adjust the volume.
Getting Started
• The setting may be restored to the default after the
batteries are replaced. If this happens, reset it.
54
En
Getting Started
TV preset code list
Manufacturer Code(s)
3
Getting Started
PIONEER 00, 31, 32, 07, 36,
42, 51, 22
ACURA 44
ADMIRAL 31
AIWA 60
AKAI 32, 35, 42
AKURA 41
ALBA 07, 39, 41, 44
AMSTRAD 42, 44, 47
ANITECH 44
ASA 45
ASUKA 41
AUDIOGONIC 07, 36
BASIC LINE 41, 44
BAUR 31, 07, 42
BEKO 38
BEON 07
BLAUPUNKT 31
BLUE SKY 41
BLUE STAR 18
BPL 18
BRANDT 36
BTC 41
BUSH 07, 41, 42, 44, 47, 56
CASCADE 44
CATHAY 07
CENTURION 07
CGB 42
CIMLINE 44
CLARIVOX 07
CLATRONIC 38
CONDOR 38
CONTEC 44
CROSLEY 32
CROWN 38, 44
CRYSTAL 42
CYBERTRON 41
DAEWOO 07, 44, 56
DAINICHI 41
DANSAI 07
DAYTON 44
DECCA 07, 48
DIXI 07, 44
DUMONT 53
ELIN 07
ELITE 41
ELTA 44
EMERSON 42
ERRES 07
FERGUSON 07, 36, 51
FINLANDIA 35, 43, 54
FINLUX 32, 07, 45, 48, 53,
54
FIRSTLINE 40, 44
FISHER 32, 35, 38, 45
FORMENTI 32, 07, 42
FRONTECH 31, 42, 46
FRONTECH/PROTECH 32
FUJITSU 48
FUNAI 40, 46, 58
GBC 32, 42
GE 00, 01, 08, 07, 10, 11,
17, 02, 28, 18
GEC 07, 34, 48
GELOSO 32, 44
GENERAL 29
GENEXXA 31, 41
GOLDSTAR 10, 23, 21, 02,
07, 50
GOODMANS 07, 39, 47, 48,
56
GORENJE 38
GPM 41
GRAETZ 31, 42
GRANADA 07, 35, 42, 43,
48
GRADIENTE 30, 57
GRANDIN 18
GRUNDIG 31, 53
HANSEATIC 07, 42
HCM 18, 44
HINARI 07, 41, 44
HISAWA 18
HITACHI 31, 33, 34, 36, 42,
43, 54, 06, 10, 24, 25, 18
HUANYU 56
HYPSON 07, 18, 46
ICE 46, 47
IMPERIAL 38, 42
INDIANA 07
INGELEN 31
INTERFUNK 31, 32, 07, 42
INTERVISION 46, 49
ISUKAI 41
ITC 42
ITT 31, 32, 42
JEC 05
JVC 13, 23
KAISUI 18, 41, 44
KAPSCH 31
KENDO 42
KENNEDY 32, 42
KORPEL 07
KOYODA 44
LEYCO 07, 40, 46, 48
LIESENK&TTER 07
LOEWE 07
LUXOR 32, 42, 43
M-ELECTRONIC 31, 44, 45,
54, 56, 07, 36, 51
MAGNADYNE 32, 49
MAGNAFON 49
MAGNAVOX 07, 10, 03, 12,
29
MANESTH 39, 46
MARANTZ 07
MARK 07
MATSUI 07, 39, 40, 42, 44,
47, 48
MCMICHAEL 34
MEDIATOR 07
MEMOREX 44
METZ 31
MINERVA 31, 53
MITSUBISHI 09, 10, 02, 21,
31
MULTITECH 44, 49
NEC 59
NECKERMANN 31, 07
NEI 07, 42
NIKKAI 05, 07, 41, 46, 48
NOBLIKO 49
NOKIA 32, 42, 52
NORDMENDE 32, 36, 51,
52
OCEANIC 31, 32, 42
ORION 32, 07, 39, 40
OSAKI 41, 46, 48
OSO 41
OSUME 48
OTTO VERSAND 31, 32, 07,
42
PALLADIUM 38
PANAMA 46
PANASONIC 31, 07, 08, 42,
22
PATHO CINEMA 42
PAUSA 44
PHILCO 32, 42
PHILIPS 31, 07, 34, 56, 68
PHOENIX 32
PHONOLA 07
PROFEX 42, 44
PROTECH 07, 42, 44, 46, 49
QUELLE 31, 32, 07, 42, 45,
53
R-LINE 07
RADIOLA 07
RADIOSHACK 10, 23, 21,
02
RBM 53
RCA 01, 10, 15, 16, 17, 18,
61, 62, 09
REDIFFUSION 32, 42
REX 31, 46
ROADSTAR 41, 44, 46
SABA 31, 36, 42, 51
SAISHO 39, 44, 46
SALORA 31, 32, 42, 43
SAMBERS 49
SAMSUNG 07, 38, 44, 46,
69, 70
SANYO 35, 45, 48, 21, 14,
91
SBR 07, 34
SCHAUB LORENZ 42
SCHNEIDER 07, 41, 47
SEG 42, 46
SEI 32, 40, 49
SELECO 31, 42
SHARP 02, 19, 27, 67, 90
SIAREM 32, 49
SIEMENS 31
SINUDYNE 32, 39, 40, 49
SKANTIC 43
SOLAVOX 31
SONOKO 07, 44
SONOLOR 31, 35
SONTEC 07
SONY 04
SOUNDWAVE 07
STANDARD 41, 44
STERN 31
SUSUMU 41
SYSLINE 07
TANDY 31, 41, 48
TASHIKO 34
TATUNG 07, 48
TEC 42
TELEAVIA 36
TELEFUNKEN 36, 37, 52
TELETECH 44
TENSAI 40, 41
THOMSON 36, 51, 52, 63
THORN 31, 07, 42, 45, 48
TOMASHI 18
TOSHIBA 05, 02, 26, 21, 53
TOWADA 42
ULTRAVOX 32, 42, 49
UNIDEN 92
UNIVERSUM 31, 07, 38, 42,
45, 46, 54
VESTEL 07
VICTOR 13
VOXSON 31
WALTHAM 43
WATSON 07
WATT RADIO 32, 42, 49
WHITE WESTINGHOUSE 07
YOKO 07, 42, 46
ZENITH 03, 20
Playback
Chapter 4
Playback
Playing discs or files
This section describes the player’s main
operations.
2.Press h OPEN/CLOSE to open the disc
tray and load the disc.
For some discs, the disc menu is displayed
automatically when playback starts. The
contents of the disc menu and the way to
operate depend on the disc.
 Resuming playback from where it was
stopped (resume playback function)
yy When g STOP is pressed during
playback, the point at which the disc
stopped is stored in the memory. When
d PLAY is pressed after that, playback
resumes from that point.
yy To cancel the resume playback function,
press g STOP while playback is stopped.
Note
yy Load the disc with the printed side facing up.
yy Several dozen seconds are required to read
the disc. Once reading is completed, the type
of disc is displayed on the player’s front panel
display.
yy When a BD with usage restrictions set by a BD
recorder is loaded, the PIN code input screen
appears. In this case, input your PIN code.
3.Press d PLAY to play the disc.
yy To pause, press e PAUSE during playback.
yy To stop, press g STOP during playback.
Note
yy Some discs start playing automatically when
the disc tray is closed.
yy DVD-Video discs have parental lock features.
Input the password registered in the player’s
settings to unlock the parental lock. For details,
see page 82.
Note
yy The resume playback function is canceled
automatically in the following cases:
–– When the disc tray is opened.
–– When the file list window is switched.
–– When the power is turned off. (For BDs
and DVDs this does not cancel the resume
playback function.)
yy When you want to continue playback from a
position you specify to be played next time, see
Continuing playback from a specified position
(Continued Viewing Playback) on page 63.
yy The resume playback function cannot be used
for some discs.
 Playback disc/file when selecting
other functions
1.Press h OPEN/CLOSE to open the disc
tray and load the disc.
2. Press HOME MEDIA GALLERY to
display the Home Media Gallery.
3. Select disc type (BDMV/BDAV/DVD
etc.).
4
Playback
En
 If the disc menu is displayed
For the types of discs and files that can be
played, see page 11. Video, image and audio
files recorded on discs are played with the
Home Media Gallery (page 64).
1.Press u STANDBY/ON to turn on the
power.
Turn the TV’s power on and switch its input
beforehand.
55
56
En
Playback
Forward and reverse scanning
Step forward and step reverse
 During playback, press mREV or
nFWD.
yy The scanning speed switches each time
the button is pressed. The speed steps
depend on the disc or file (the speed is
displayed on the TV screen).
 While playback is paused, press q/
or /r.
yy The picture moves a step forward or
reverse each time the button is pressed.
 To resume normal playback
 Press d PLAY.
 Press d PLAY.
Playing specific chapters,
tracks or files
4
Playback
 During playback, input the number
of the chapter/track/file you want to
select.
yy Use the number buttons (0 to 9) to input
the number, then press ENTER.
yy Press CLEAR to clear the values you have
input.
Skipping content
 During playback, press o or p.
yy When p is pressed, the playback
skips ahead to the beginning of the next
chapter/track/file.
yy When o is pressed while a video or
audio file is playing, the playback skips
back to the beginning of the currently
playing chapter/track/file. Press twice to
skip back to the beginning of the previous
chapter/track/file.
yy When o is pressed while an image
file is playing, playback returns to the
previous file.
Playing in slow motion
 While playback is paused, press and
hold q/ or /r.
yy The speed switches each time the button
is pressed (the speed is displayed on the
TV screen).
 To resume normal playback
 Press d PLAY.
 To resume normal playback
Playing a specific section
within a title or track
repeatedly (A-B Repeat)
Use this procedure to play a specific section
within a title or track repeatedly.
1 During playback, press A-B to select the
starting point.
yy A- is displayed on the TV screen.
2. During playback, press A-B to select the
ending point.
yy A-B Repeat playback starts.
 To cancel A-B Repeat play
yy Press A-B during the A-B Repeat play.
Note
yy A-B Repeat play is canceled in the following
cases:
–– When you search outside of the repeat
range.
–– When you start other Repeat Play or
Random Play.
Playing repeatedly
(Repeat Play)
Use this procedure to play the currently playing
disc, title, chapter, track or file repeatedly.
 During playback, press REPEAT.
yy Each time you press REPEAT the type of
repeat modes changes as shown below.
BD
Current chapter d Current title
DVD
Current chapter d Current title d All
titles
CD/Video file/Audio file/Image file
Current track/file d All tracks/All files in
folder
Playback
 To cancel Repeat Play
yy Press REPEAT several times during
Repeat Play.
Note
yy Repeat Play is canceled in the following cases:
–– When you search outside the repeat range.
–– When you start other Repeat Play or
Random Play.
57
En
Making bookmarks
You can make bookmarks on the video
currently playing and play back the scene later.
 During playback, press BOOKMARK.
yy The bookmark is made.
yy Maximum number of bookmarks are 12.
 Playing the bookmarked scene
Playing in the desired order
(Programmed Play)
1. Press and hold BOOKMARK for a few
seconds.
yy The list of bookmarks is displayed.
1 During playback, press PROGRAM.
yy The program screen is displayed.
2. Select the bookmark you want to play.
Use / to select, then press ENTER.
2. Select the program number.
Use / to select, then press ENTER.
 Deleting the bookmark
4. Select the chapter you want to play.
Use / to select, then press ENTER.
5.Press d PLAY.
yy Playback starts.
 Editing the program
1. Select the program number you want to
edit, then press ENTER.
2. Select title/chapter, then press ENTER.
 Deleting the program
 Select the program number you want to
delete, then press CLEAR.
yy To delete all the programs, press
RETURN.
Note
yy When you use audio CDs for Programmed Play,
enter the track number in step 3.
yy This function does not work with BDs.
 Select the bookmark you want to
delete, then press CLEAR.
yy Bookmarks may not be allowed to make
for some discs.
yy Bookmarks are canceled in the following
cases:
–– When the player’s power turned off.
–– When the disc tray is opened.
Zoom
 During playback, press ZOOM.
yy Each time you press ZOOM, the zoom
level changes as shown below.
Zoom 2x d Zoom 3x d Zoom 4x d
Zoom 1/2 d Zoom 1/3 d Zoom 1/4 d
Normal (not displayed)
Note
yy This function does not work with some discs.
4
Playback
3. Select the title you want to play.
Use / to select, then press .
58
En
Playback
Playing photos as slideshows
Switching the subtitles
This function plays the photos, switching them
automatically.
For discs or files on which multiple subtitles
are recorded, the subtitles can be switched
during playback.
 During playback, press INDEX.
yy Display the thumbnail of image files. The
maximum number is 12 at once.
yy If you select one of the image and press
ENTER, slideshow will start from the
image you selected.
 Rotating/inverting photos
When a slideshow is playing or paused, the
display switches as shown below when the /
/ / buttons are pressed.
4
button: Rotates 90° clockwise
button: Rotates 90° counterclockwise
button: Flips horizontally
button: Flips vertically
Playback
Switching the camera angles
For BD-ROM and DVD-Video discs on which
multiple angles are recorded, the angles can
be switched during playback.
 During playback, press ANGLE.
yy The current angle and total number of
recorded angles are displayed on the TV
screen.
To switch the angles, press ANGLE again.
yy The angles can also be switched by
selecting Angle from the TOOLS menu.
yy If the angles are not switched when
ANGLE is pressed, switch them from the
disc menu screen.
Caution
yy The subtitles cannot be switched for discs
recorded by a DVD or BD recorder. Also refer to
the operating instructions for the device used
for recording.
 During playback, press SUBTITLE.
yy The current subtitle and total number of
recorded subtitles are displayed on the
TV screen.
To switch the subtitle, press SUBTITLE
again.
yy The subtitles can also be switched by
selecting Subtitle from the TOOLS menu.
yy If the subtitles are not switched when
SUBTITLE is pressed, switch them from
the disc menu screen.
 Turning the subtitles off
 Press SUBTITLE several times or select
Subtitle from the TOOLS menu to
switch the setting to Off.
 About displaying external subtitle
files while playing DivX media files
In addition to the subtitles recorded in DivX
media files, this player also supports the
display of external subtitle files. If a file has the
same name as that of a DivX media file aside
from the file extension and the extension is one
of the extensions listed below, the file is treated
as an external subtitle file. Note that DivX
media files and external subtitle files must be
located in the same folder.
Only one external subtitle file can be displayed
on this player. Use a computer, etc., to delete
any external subtitle files you do not want to
display from the disc.
Note
yy Depending on the file, the external subtitles
may not be displayed properly.
Playback
Switching the audio
For discs or files on which multiple audio
streams/channels are recorded, audio streams/
channels can be switched during playback.
 During playback, press AUDIO.
yy The current audio and total number of
recorded audio streams are displayed on
the TV screen. To switch the audio, press
AUDIO again.
yy The audio can also be switched by
selecting Audio from the TOOLS menu.
yy If the audio is not switched when AUDIO
is pressed, switch it from the disc menu
screen.
Switching the CD/SACD
playback area
2. Open the disc tray.
Press the  OPEN/CLOSE button.
3 Close the disc tray.
Press the  OPEN/CLOSE button. Once the
disc is loaded, the playback area switches.
En
Displaying the disc
information
 Press DISPLAY.
The disc information appears on the TV screen.
To switch off the information display, press
DISPLAY again.
The information display differs between during
playback and when playback is stopped.
4
Playback
1. Select the area you want to play.
In the stop mode, press CD/SACD. The
playback area switches on the front panel
display window each time the button is
pressed.
[CD AREA]  [SACD 2CH]  [SACD MCH]
 (back to beginning)
yy During playback, press  STOP twice to
cancel continuous play before selecting
the playback area.
59
60
En
Playback
Enjoying BONUSVIEW or
BD-LIVE
This player is compatible with BD-Video
BONUSVIEW and BD-LIVE.
When using BD-Video discs compatible with
BONUSVIEW, you can enjoy such functions
as secondary video (picture in picture) (page
62) and secondary audio (page 62). With BDVideo discs supporting BD-LIVE, special video
images and other data can be downloaded
from the Internet.
4
Data recorded on BD video and downloaded
from BD-LIVE is stored on the USB flash drive
(external memory). To enjoy these functions,
connect a USB flash drive (minimum 1 GB
capacity, 2 GB or greater recommended)
supporting USB 2.0 High Speed (480 Mbit/s) to
the USB port.
Playback
• When you insert or remove a USB flash
drive, be sure to turn the player’s power off.
• To recall data stored in the USB flash drive,
first insert the disc media that was being
used at the time the data was downloaded (if
a different disc is loaded, the data stored on
the USB flash drive cannot be played).
• If a USB flash drive containing other data
(previously recorded) is used, the video and
audio may not play back properly.
• Do not disconnect the USB flash drive while
playback is in progress.
• Some time may be required for the data to
load (read/write).
Caution
• It may not be possible to use the BONUSVIEW and
BD-LIVE functions if there is insufficient space on
the USB flash drive. In this case, refer to Erasing
data that has been added to BDs and application
data on page 81 for erasing the Virtual Package
data and the BD-LIVE data in the USB flash drive.
Note
• Operation of USB flash drives is not guaranteed.
• Playback of BD-LIVE function data differs
depending on the disc used. For details, consult
the user instructions supplied with the disc.
• To enjoy the BD-LIVE function, a network
connection and settings are required (pages 46
and 80).
• BD-LIVE is a function that provides for connection
to the Internet. Discs supporting the BD-LIVE
function may send ID codes identifying this player
and the disc to the contents provider via the
Internet.
Playback
61
En
Playback functions
The functions that can be used differ according to the type of disc and file. In some cases, some of
the functions cannot be used. Check the usable functions on the table below.
Disc/file type
Function1
BDROM
BD-R
/-RE
DVD-R
Video
DVD/-RW
AVCREC AVCHD
file
Video
(VR
format)
Image
file
Audio
file
Audio
CD
Forward and
reverse scanning2
1
3
1
3
1
3
1
3
1
3
1
3
1

1
1
Playing specific
titles, chapters or
tracks
1
1
1
1
1
1



1
3
4
4
Skipping content
1
1
1
1
1
1
1
1
1
1
Slow motion play2,5
1
1
1
1
1
1
1
6
1


Step forward and
step reverse2
1
1
1
1
1
1
1
7
1


2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

A-B Repeat play
Zoom
1
1
1
1
1
1
1
1

Angle8
1

1







Subtitle9
1
1
1
1
1
1
1



Audio10
1
1
1
1
1
1
1



Disc information
1
1
1
1
1
1
1
1
1
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
Some functions may not work for some discs or files, even if indicated [1] on the table.
For some discs, normal playback resumes automatically when the chapter switches.
No sound is produced during forward and reverse scanning.
Sound is produced during forward and reverse scanning.
• No sound is output during slow motion playback.
• It is not possible to switch the speed during reverse slow motion playback.
Reverse slow motion playback is not possible.
Reverse step playback is not possible.
Angle mark is displayed for scenes at which multiple angles are recorded if Angle Mark is set to On (page 78).
• The types of recorded subtitles depend on the disc and file.
• In some cases, the subtitle may switch or the switching screen provided on the disc may be displayed
immediately, without the current subtitle or the total number of subtitles recorded on the disc being displayed.
10.The types of recorded audio streams depend on the disc and file.
4
Playback
1
Repeat Play
62
Playback
En
Using the TOOLS menu
Item
Description
Various functions can be called out according
to the player’s operating status.
Still off
Switch off the BD-ROM’s still picture.
Ins Search
Skip forward 30 seconds.
Ins Replay
Skip backward 10 seconds.
Slide Show
Switch the playback speed while
playing the picture slide show.
Transition
Change the style of the slide show
while playing the picture slide show.
1. Display the TOOLS menu.
Press TOOLS during playback.
2. Select and set the item.
Use / to select, then press ENTER.
Note
yy Items that cannot be changed are displayed in
gray. The items that can be selected depend on
the player’s status.
 To change the setting of the selected
item
Use
4
/
to change.
 To close the TOOLS menu
Press TOOLS.
Playback
 TOOLS menu item list
Item
Description
Title
Display the title information for
the currently playing disc and total
number of titles on the disc. Also
select the title you want to play. (See
the following description.)
Chapter
(track/file)1
Display the information for the
currently playing chapter (track/
file) and total number of chapters
in the disc. Also select the chapter
(track/file) you want to play. (See the
following description.)
Time
Display the elapsed or remaining
time.
Also enter the time from which you
want to start playback. (See the
following description.)
Mode
Switch the play mode (page 63).
Audio
Switch the audio.
Angle
Switch the BD-ROM/DVD-Video
disc’s camera angle.
Subtitle
Switch the subtitle language.
Code Page
Switch the subtitle code page.
Secondary
Video2
Switch the BD-ROM’s secondary
video (Picture-in-Picture).
Secondary
Audio3
Switch the BD-ROM’s secondary
audio.
Bitrate
Display the bitrate of the audio/video/
secondary video/secondary audio.
1. One of these types of information is displayed,
depending on the type of disc.
2. Secondary video mark is displayed for scenes at
which secondary video is recorded if PIP Mark is
set to On (page 78).
3. Secondary audio mark is displayed for scenes at
which secondary audio is recorded if Secondary
Audio Mark is set to On (page 78).
Note
yy Selectable items depend on the type of disc.
yy The types of recorded secondary audio streams
depend on the disc and file.
yy Some discs do not include secondary audio/
secondary video.
yy In some cases, the secondary audio/secondary
video may switch or the switching screen
provided on the disc may be displayed
immediately, without the current secondary
audio/secondary video or the total number
of secondary audio/secondary video streams
recorded on the disc being displayed.
Playing from a specific time
(Time Search)
1. Select Time.
Use / to select, then press ENTER.
2. Input the time.
Use the number buttons (0 to 9) to input the
time.
yy To play from 45 minutes, input 0, 0, 4, 5, 0
and 0, then press ENTER.
yy To play from 1 hour 20 minutes, input 0, 1,
2, 0, 0 and 0, then press ENTER.
yy Press CLEAR to clear the values you have
input.
3. Starting playback from the specified
time.
Press ENTER.
Playback
Playing a specific title, chapter,
track or file (Search)
1. Select Title or Chapter (track/file).
Use / to select, then press ENTER.
2. Input the Title or Chapter (track/file)
number.
Use the number buttons (0 to 9) or / to
input the number.
yy To search for title 32, input 3 and 2, then
press ENTER.
yy Press CLEAR to clear the values you have
input.
3. Starting playback from the specified
title, chapter or track.
Press ENTER.
You can select from 2 types of random
playback.
1. Select Mode.
Use / to select, then press ENTER.
2. Select the playing mode.
Use / to select, then press ENTER.
 Random play
The specified range of discs, titles or chapter
(track/file) is played in random order. The same
item may be played consecutively.
 Shuffle play
The specified range of discs, titles or chapter
(track/file) is played in random order. Each item
is played once.
En
Continuing playback from a
specified position (Continued
Viewing Playback)
This function allows you to continue playback
from a position you specify to be played next
time, even after turning the power off.
Setting
 During playback, press CONTINUED
at the position from which you want to
start continued viewing playback.
The elapsed playing time at the specified
position is displayed on the TV screen.
Playing
1.Press d PLAY to play the title for
which you have set continued viewing
playback.
The continued viewing playback
confirmation screen appears.
2.Use / to select Yes, then press
ENTER.
Playback starts from the specified position.
Note
yy The continued viewing playback setting is
canceled when h OPEN/CLOSE is pressed.
yy Continued viewing playback may not work
properly with some discs.
4
Playback
Playing specified range of
discs, titles or chapter (track/
file) in random order
63
64
En
Playback from Home Media Gallery
Chapter 5
Playback from Home
Media Gallery
About Home Media
Gallery
Note
• The Home Media Gallery allows you to play files on
media servers connected to the same Local Area
Network (LAN) as the unit.
• The following files are allowed to be played from
Home Media Gallery:
–– PCs running Microsoft Windows Vista or XP
with Windows Media Player 11 installed
–– PCs running Microsoft Windows 7 with
Windows Media Player 12 installed
–– DLNA-compatible digital media servers (on PCs
or other components)
Files stored in a PC or DMS (Digital Media Server)
as described above can be played by Digital Media
Player (DMP). The player supports the use of such
DMP.
• To play back audio files stored on components
on the network, you must turn on the DHCP
server function of your router. In case your router
does not have the built-in DHCP server function,
it is necessary to set up the network manually.
Otherwise, you cannot play back files stored on
components on the network. See page 80.
About network playback
5
Playback from Home Media Gallery
The network playback function of this unit uses
the following technologies:
 Windows Media Player
This player’s Home Media Gallery function
allows you to display a list of input sources and
start playback. This chapter describes setup and
playback procedures required to enjoy these
features. When you play the files stored on your
computer or the components on the network, it
is advisory that you also refer to the operation
manual supplied with your network component.
See Windows Media Player 11/Windows Media
Player 12 above for more on this.
DLNA
The input sources that can be played from
Home Media Gallery are as shown below.
• BD-R/RE (BDAV format) discs
DLNA CERTIFIED® Audio Player
• DVD-R/RW (VR format) discs
The Digital Living Network Alliance (DLNA)
is a cross-industry organization of consumer
electronics, computing industry and mobile
device companies. Digital Living provides
consumers with easy sharing of digital media
through a wired or wireless network in the
home.
• Audio CDs (CD-DA, SACD and DTS CDs)
• DVD/CDs on which only data files of video,
image or audio files, etc. are recorded.
• USB device
• Files on the network servers (on the PCs or
components connected to the player via LAN
interface.)
Playback from Home Media Gallery
The DLNA certification logo makes it easy
to find products that comply with the DLNA
Interoperability Guidelines. This unit complies
with DLNA Interoperability Guidelines v1.5.
When a PC running DLNA server software or a
DLNA compatible device is connected to this
player, some setting changes of software or
other devices may be required. Please refer to
the operating instructions for the software or
device for more information.
DLNA®, the DLNA Logo and DLNA CERTIFIED®
are trademarks, service marks, or certification
marks of the Digital Living Network Alliance.
 Content playable over a network
• Even when encoded in a compatible format,
some files may not play correctly.
• Some functions may not be supported
depending on the server type or version
used.
 Disclaimer for Third Party Content
Access to content provided by third parties
requires a high speed Internet connection and
may also require account registration and a
paid subscription.
Third party content services may be changed,
suspended, interrupted, or discontinued at any
time without notice, and Pioneer disclaims any
liability in connection with such occurrences.
Pioneer does not represent or warrant that
content services will continue to be provided
or available for a particular period of time,
and any such warranty, express or implied, is
disclaimed.
En
 About playback behavior over a
network
• Playback may stall when the PC is switched
off or any media files stored on it are deleted
while playing content.
• If there are problems within the network
environment (heavy network traffic, etc.)
content may not be displayed or played
properly (playback may be interrupted or
stalled). For best performance, a 10BASE-T/
100BASE-TX connection between the player
and the PC is recommended.
• If several clients are playing simultaneously,
as the case may be, playback is interrupted
or stalled.
• Depending on the security software installed
on a connected PC and the setting of such
software, network connection may be
blocked.
Pioneer is not responsible for any malfunction
of the player and/or the Home Media
Gallery features due to communication
errors/malfunctions associated with your
network connection and/or your PC, or other
connected equipment. Please contact your PC
manufacturer or Internet service provider.
Windows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
Microsoft®, Windows®7, Windows®Vista,
Windows®XP, Windows®2000,
Windows®Millennium Edition, Windows®98, and
WindowsNT® are either registered trademarks
or trademarks of Microsoft Corporation in the
United States and/or other countries.
5
Playback from Home Media Gallery
• Supported file formats vary by server. As
such, files not supported by your server
are not displayed on this unit. For more
information check with the manufacturer of
your server.
65
66
En
Playback from Home Media Gallery
Playback file on the
network
1. Press HOME MEDIA GALLERY to
display the Home Media Gallery.
The Home Media Gallery can also be
displayed by selecting [Home Media Gallery]
from Home Menu, then pressing ENTER.
2. Select the server which contains the file
you want to play.
3. Select the file you want to play.
Use / to select, then press ENTER.
 To end Home Media Gallery
Press HOME MEDIA GALLERY.
Note
• If you are unable to display the servers on the
Home Media Gallery screen, select [DLNA Search]
and press ENTER.
5
Disc/USB playback
1. Press HOME MEDIA GALLERY to
display the Home Media Gallery.
The Home Media Gallery can also be
displayed by selecting Home Media Gallery
from Home Menu, then pressing ENTER.
2. Select Disc or USB.
Use / to select, then press ENTER.
3. Select Photo/Music/Video/AVCHD.
Use / to select, then press ENTER.
yy This step is not for the discs that have
been recorded with BDAV/VR/AVCREC
format.
yy To play files in AVCHD format on a USB
device, create a folder named "AVCHD"
on the USB device, then copy the "BDMV"
folder containing which the files to be
played into the "AVCHD" folder.
Playback from Home Media Gallery
4. Select the title/track or file you want to
play.
Use / to select, then press ENTER.
Playback starts from the selected title/track
or file.
yy If the file you want to play is in the folder,
select the folder that contains the file
first.
Playing back image files
 About Slideshow
A display of the files on the disc or in the folder
switches automatically.
Note
• When playing an audio CD (CD-DA/SACD/DTSCD), the Now Playing screen is displayed.
• Some BD-R/-RE discs have playback protection. To
cancel the protection, input the password set for
the disc.
• It may take a few seconds before playback starts.
This is normal.
• It may not be possible to play some files properly.
• The number of views may be restricted.
• Depending on the connected devices and
conditions, some time may be required for
playback to start and for the image to switch.
Playback from Home Media Gallery
Playing in the desired
order (Playlist)
The discs that can add tracks and files to the
Playlist are as shown below.
• DVDs/CDs/USB devices on which audio files
are recorded
Adding tracks/files
Use this procedure to add tracks and files, and
create the Playlist.
1. Press HOME MEDIA GALLERY to
display the Home Media Gallery.
The Home Media Gallery can also be
displayed by selecting Home Media Gallery
from Home Menu, then pressing ENTER.
2. Select Disc or USB.
Load the disc beforehand.
Use / to select, then press ENTER.
67
En
Playing the playlist
1. Press HOME MEDIA GALLERY to
display the Home Media Gallery.
The Home Media Gallery can also be
displayed by selecting Home Media Gallery
from Home Menu, then pressing ENTER.
2. Select Playlist.
Use / to select, then press ENTER.
3. Select the track/file to be played.
Use / to select, then press ENTER.
Playback starts from the selected track/
file and continues until the end of the list is
reached. Use o/p to play the previous
or next track/file. The Now Playing screen is
displayed.
Deleting tracks/files from the
playlist
1. Select the track/file to be deleted, then
press POP UP MENU to display the
POP UP MENU menu.
4. Press POP UP MENU to display the
POP UP MENU menu.
2.Use / to select Remove from Playlist,
then press ENTER.
5. Select Add to Playlist to add to Playlist.
Use / to select, then press ENTER.
The track or file selected in step 3 is added
to the Playlist.
yy To add more tracks or files, repeat steps 3
to 5.
5
Playback from Home Media Gallery
3. Select the track/file to be added.
Use to select.
68
En
Playing the web contents
Chapter 6
Playing the web contents
You can enjoy some streaming contents on the
Internet with the player.
Available web contents
Playing the items
Caution
You must connect the player to the Internet
beforehand. See Connecting to your Home Network on
page 46 for the details.
• YouTube (MPEG4 AVC H.264)
• Picasa
Note
About YouTube
• YouTube videos of the following sizes can be played.
–– Standard quality (400 x 226 pixels, 200 kbps)
–– Medium quality (480 x 360 pixels, 512 kbps)
–– High quality (854 x 480 pixels, 900 kbps)
–– HD (720p) (1280 x 720 pixels, 2 Mbps)
–– HD (1080p) (1920 x 1080 pixels, 4 Mbps)
• This player supports the YouTube Leanback service.
The Youtube Leanback service is only available in
English for now.
Refer to YouTube Help at http://www.google.com/
support/youtube/ for further information.
• YouTube videos for mobile phones cannot be played.
• Some YouTube videos cannot be played.
6
Playing the web contents
About Picasa
• Picasa is available only in English. Refer to
instructions at http://picasa.google.com/support/
for details.
–– Register your user name and password on the
PC before you use Picasa Web Albums.
–– When you access Picasa from this player for the
first time, select the New User icon and enter
your registered user name and password.
• Depending on the Internet connection environment,
it may not be possible to play web contents properly.
• To access to web contents, this player requires a
broadband Internet connection. A contract with
an Internet provider is required for a broadband
Internet connection.
• Access to content provided by third parties requires
a high speed Internet connection and may also
require account registration and a paid subscription.
Third party content services may be changed,
suspended, interrupted, or discontinued at any time
without notice, and Pioneer disclaims any liability in
connection with such occurrences.
Pioneer does not represent or warrant that content
services will continue to be provided or available for
a particular period of time, and any such warranty,
express or implied, is disclaimed.
• Disc playback and this function cannot be used at
the same time.
1. Display the selection screen.
The selection screen can be selected by
HOME MENU then selecting
pressing
Web Contents d Desired web content.
2. Select the type of web contents.
Use / to select, then press ENTER.
3.Press / to select the item you want
to play, then press ENTER.
To stop playback, press EXIT. Playback of
the video stops and the Home Menu screen
reappears.
Other Operating
Chapter 7
Other Operating
Recording Audio CD to a
USB device
You can record audio CD to a USB device using
this player.
1. Insert an USB device into the USB port
on the front panel.
Note
yy Please connect only one USB device.
2. Open the disc tray and place an Audio
CD on the tray.
Press  OPEN/CLOSE.
69
En
7. Start recording.
Use / / / to select [Start] and press
ENTER to start recording.
8. Exit CD recording display.
Use / / / to select [Cancel] then press
ENTER after recording has finished.
Note
• Use cursor / / / to select [Bitrate] then press
ENTER to change the Bitrate setting.
The set speed will change each time [Bitrate] is
pressed. The set value can be selected from those
shown below.
[64kbps]  [96kbps]  [128kbps]  [192kbps]
 [256kbps]  [320kbps]
• A folder will be created on the USB device when
recording starts. The maximum number of folders
that can be created is 100.
3. Close disc tray.
When  OPEN/CLOSE is pressed, playback
will start automatically.
yy If playback does not start automatically,
press the  PLAY on the remote or /
(PLAY/PAUSE) on the device to start
playback.
4. Press USB REC during CD playback.
[CD RIP] will be displayed.
yy If there are more than one Track you want
to record, repeat the step for 5.
yy If you want to delete a selected Track use
/ / / to select [Select None] and
press ENTER.
6. Set the recording speed
Use / / / to select [Speed] and press
ENTER.
yy The recording speed will change each
time ENTER is pressed. The recording
speed will change as shown below.
Normal: when recording while listening
to the music.
Fast: will record at approx 4x speed. You
cannot listen to the music.
7
Other Operating
5. Select the song or the Track No. you
want to record.
If you are recording all the songs on the CD
use / / / to select [Select all] and press
ENTER.
If you are selecting a Track to record use
/ / / to select the Track No. and press
ENTER.
70
En
Other Operating
iPod/iPhone playback
Rear of the unit
Merely by connecting your iPod/iPhone to this
unit, you can enjoy high-quality sound from
your iPod/iPhone. You can also enjoy images
with this unit.
Playback and volume level setting for iPod/
iPhone music and images can be performed
from this unit or the iPod/iPhone itself.
Supported iPod and iPhone models:
– iPod touch (4th/3rd/2nd/1st generation)
– iPod classic
– iPod nano (6th/5th/4th/3rd/2nd generation)
– iPhone 4S/4/3GS/3G
TV
• The iPod nano 6G cannot play back video,
but can play slide shows only.
• This system has been developed and tested
for the software version of iPod/iPhone
indicated on the website of Pioneer (http://
pioneer.jp/homeav/support/ios/eu/).
• Installing software versions other than
indicated on the website of Pioneer to your
iPod/iPhone may result in incompatibility
with this system.
• When using an iPod/iPhone not supported
by this unit, use a commercially available
cable to connect the iPod/iPhone to the
PORTABLE IN connector of this unit.
• Before connecting the iPod, turn this unit
off and reduce the volume of this unit to its
minimum.
7
Other Operating
1. Connect the cradle so that the mark  is
downwards. Put your iPod/iPhone on it.
Connect the iPod/iPhone firmly.
If you turn this unit on, your iPod/iPhone
is automatically turned on and recharging
starts.
2. Connecting to the TV.
To enjoy displaying images from the iPod/
iPhone on the TV, connect the VIDEO OUT of
the iPod cradle and the video input terminal
on your TV. You will need the video cable
which comes with this unit to connect. If
you are already using the video cable which
comes with this unit to connect this unit
and the TV, use a commercially available
video cable.
Note
• Some iPod allow the TV output setting to be
changed while connected.
• When the iPod/iPhone is disconnected from this
unit, the iPod/iPhone’s TV output setting returns to
its original state.
• Some functions may be restricted depending on
the model or software version.
• iPod/iPhone is licensed for reproduction of noncopyrighted materials or materials the user is
legally permitted to reproduce.
• Features such as the equalizer cannot be controlled
using this system, and we recommend switching
the equalizer off before connecting.
• Pioneer cannot under any circumstances accept
responsibility for any direct or indirect loss arising
from any inconvenience or loss of recorded
material resulting from iPod/iPhone failure.
• For detailed instructions on using the iPod/iPhone,
please refer to the manual supplied with the iPod/
iPhone.
Other Operating
Playing your iPod/iPhone
Caution
• When your iPod/iPhone is connected to this unit
and you wish to operate the iPod/iPhone directly,
be sure to hold the iPod/iPhone steady with the
other hand to prevent malfunctions due to faulty
contacts.
1. Connect your iPod/iPhone.
To connect your iPod/iPhone, see
Connecting your iPod/iPhone on page 70.
2. Press FUNCTION to select iPod as the
input source and press ENTER.
Button
What it does
 PLAY
Starts normal playback.
 PAUSE
Pauses playback.
 STOP
Pauses playback.
 PREV
Press to skip to the start of the
current file, then previous files.
 NEXT
Press to skip to the next file.

Press to start fast reverse scanning.

Press to start fast forward scanning.
MENU
Use to access the iPod/iPhone menu.
/ /ENTER
71
En
Important
• If this unit cannot play your iPod/iPhone,
perform the following troubleshooting
checks:
–– Check whether the iPod/iPhone is
supported by this unit.
–– Reconnect the iPod/iPhone to the unit. If
this doesn’t seem to work, try resetting
your iPod/iPhone.
–– Check the iPod/iPhone software is
supported by this unit.
• If the iPod/iPhone cannot be operated, check
the following items:
–– Is the iPod/iPhone connected correctly?
Reconnect the iPod/iPhone to the unit.
–– Is the iPod/iPhone experiencing a
hangup? Try resetting the iPod/iPhone,
and reconnect it to the unit.
Note
• When input is switched from iPod to another
function, iPod/iPhone playback is temporarily
stopped.
Use to control the iPod/iPhone
menu.
7
Other Operating
72
En
Other Operating
Radio Operations
Improving poor FM reception
Be sure that FM aerial is connected. (Refer to
the page 43)
Listening to the radio
1.Press FUNCTION until FM appears in the
display window and press ENTER.
The last received station is tuned in.
2. Scanning will start when either the  or
the  button is pressed.
or
Press
/
repeatedly.
or
Press TUNE –/+ on the front panel of the
player repeatedly.
3. Adjust the volume by rotating VOLUME on
the front panel or by pressing VOL + or
VOL – on the remote control repeatedly.
Presetting the radio stations
You can preset 50 stations for FM.
Before tuning, make sure that you have turned
down the volume.
1.Press FUNCTION until FM appears in the
display window and press ENTER.
The last received station is tuned in.
2. Select the desired frequency by using
7
/ .
3.Press PROGRAM a preset number will flash
in the display window.
Other Operating
4.Press
want.
/
to select the preset number you
5.Press PROGRAM.
The station is stored.
6. Repeat the steps 2 to 5 to store other
stations.
7. You can select the stored station by
pressing / .
Deleting all the saved stations
1. Press and hold g STOP for two seconds.
[ERASE ALL] will flash up on the display
window.
2.Press g STOP to erase all of the saved radio
stations.
Press AUDIO on the remote control. This will
change the tuner from stereo to mono and
usually improve the reception.
Seeing information about a
radio station
The FM tuner is supplied with the RDS (Radio
Data System) facility. This shows information
about the radio station being listened to. Press
BOOKMARK (RDS) repeatedly to cycle through
the various data types:
PS
(Programme Service Name)
The name of the channel will appear
in the display.
PTY
(Programme Type Recognition)
The programme type (e.g. Jazz or
News) will appear in the display.
RT
(Radio Text)
A text message contains special
information from the broadcast
station. This text may scroll across
the display.
You can search the radio stations by
programme type by pressing BOOKMARK (RDS).
The display will show the last PTY in use. Press
ZOOM (PTY) one or more times to select your
preferred programme type. Press and hold /
. The tuner will search automatically. When a
station is found the search will stop.
Other Operating
73
En
Bluetooth® ADAPTER for
Wireless Enjoyment of
Music
Listen to music on a Bluetooth
wireless technology enabled
device
• Bluetooth wireless technology enabled
device: cell phone
Pairing of the unit and a Bluetooth
wireless technology enabled device.
(Initial registration)
• Bluetooth wireless technology enabled
device: Digital music player
• Device not equipped with Bluetooth wireless
technology: Digital music player + Bluetooth
audio transmitter (sold commercially)
Wireless music play
When the Bluetooth ADAPTER (Pioneer Model
No. AS-BT100 or AS-BT200) is connected to
this unit, a product equipped with Bluetooth
wireless technology (portable cell phone, digital
music player, etc.) can be used to listen to
music wirelessly. Also, by using a commercially
available transmitter supporting Bluetooth
wireless technology, you can listen to music on
a device not equipped with Bluetooth wireless
technology. The AS-BT100 and AS-BT200 model
supports SCMS-T contents protection, so music
can also be enjoyed on devices equipped with
SCMS-T type Bluetooth wireless technology.
• With the AS-BT100, some functions may not
be available on this unit.
• It must be necessary that the Bluetooth
wireless technology enabled device supports
A2DP profiles.
• Pioneer does not guarantee proper connection and
operation of this unit with all Bluetooth wireless
technology enabled devices.
• About one minute is required between turning the
power on and completion of startup.
1. Press FUNCTION and change input to
BLUETOOTH and press ENTER.
After [BLUETOOTH] is displayed in the
unit’s display window, [READY] will then be
displayed.
2. Operate the Bluetooth wireless
technology enabled device and perform
pairing.
When a Bluetooth wireless technology
enabled device searches for this unit, some
Bluetooth wireless technology enabled
devices will display a list of supported
devices on their display section. This unit
will be displayed as Bluetooth ADAPTER
[AS-BT100] or [AS-BT200].
3. Enter the PIN code.
Pin code: 0000
This unit cannot be set with any PIN code
other than 0000.
4. When the unit and a Bluetooth
wireless technology enabled device
are successfully paired, [SINK] will be
displayed in the unit’s display window.
Note
yy The pairing method may differ depending
on the type of Bluetooth wireless technology
enabled device.
5. Playback music using the Bluetooth
wireless technology enabled device.
Please see the user manual of your
Bluetooth wireless technology enabled
device for details on how to playback music.
7
Other Operating
Note
Prior to starting pairing, make sure that the
Bluetooth function on your Bluetooth wireless
technology enabled device is turned on. Please
see the user manual of your Bluetooth wireless
technology enabled device for more details. The
pairing operation only needs to be performed
once, and then is not required again.
74
En
Other Operating
Note
• This unit does not support AVRCP.
• This unit does not support Mono Headset Profile
(Hands Free Profile).
• A Bluetooth wireless technology enabled device
cannot be operated by this unit.
• This unit cannot be used to listen to one seg
sounds on a Bluetooth wireless technology enabled
device. Music contents protected by SCMS-T
cannot be listened to.
• Only one Bluetooth wireless technology enabled
device may be paired with this unit; multiple
pairing is not possible.
• You may be unable to use the Bluetooth function,
depending on the type of Bluetooth wireless
technology enabled device.
• When not connected by Bluetooth, [READY] will be
displayed in the unit’s display window.
• If a Bluetooth adapter is not connected, [NO DEV]
will be displayed on the display window of the
player.
• Other electro-magnetic waves may cause
interference with the connection, causing the
sound to cut out.
• If medical equipment, microwaves, wireless
LAN routers etc. on the same frequency cause
malfunction to occur, the Bluetooth connection will
be lost.
• Even if the distance between the Bluetooth wireless
technology enabled device and the unit is less than
10 meters, if there are other obstacles in between
the two of them then you will be unable to connect
the Bluetooth wireless technology enabled device.
7
Other Operating
• If an obstacle comes between the Bluetooth
wireless technology enabled device and the unit to
interrupt communication, the Bluetooth connection
will be lost.
• If the Bluetooth wireless technology enabled device
and the unit move apart then sound quality will fall,
and if they move beyond the operating range the
Bluetooth connection will be lost.
• If the power to the unit is cut or the Bluetooth
wireless technology enabled device is moved
more than 10 meters from the unit, the Bluetooth
connection will be lost.
Karaoke
1. Press KARAOKE on the remote control.
Karaoke Setup under Initial Setup will be
displayed on the TV screen.
2. Turn the Karaoke Switch on.
Select [Karaoke Setup]  [Karaoke Switch]
 [On] using cursor and press ENTER.
3. Adjust microphone volume.
Select [Karaoke Setup]  [Microphone
Setup]  [Mic Volume] using cursor and
press ENTER.
Use / to adjust the microphone volume.
Press RETURN to finish.
4. Adjust microphone echo.
Select [Karaoke Setup]  [Microphone
Setup]  [Mic Echo] using cursor and press
ENTER.
Use cursor / to adjust the microphone
echo.
Press RETURN to finish.
5. Switch Vocal Cancel on or off.
Use cursor to select [Karaoke Setup] 
[Vocal Cancel]  [On] or [Off] and press
ENTER.
Note
• Karaoke can only be used with disc playback or
USB playback.
• Depending on the song, Vocal Cancel may not be
effective.
• When inserting the MIC terminal, support the
top of the unit with your hand to prevent it from
moving.
• The microphone volume can also be adjusted using
the MIC VOL +/– button on the remote control.
• If you turn on Vocal Cancel, the sound setting is
turned off. If you turn on the sound setting when
Vocal Cancel is on, Vocal Cancel is turned off.
Other Operating
75
En
Sound
Press SOUND on the remote control to display the sound select menu on the TV screen.
Use cursor button to make a selection, then press ENTER.
Press SOUND to exit the Sound Menu.
Note
• When HDMI IN 1 or HDMI IN 2 is selected, the Sound Menu cannot be displayed. Switch to other input source
and then switch the Sound.
• When HDMI IN 1 or HDMI IN 2 is selected, VIRTUAL 3D SOUND and SOUND RETRIEVER buttons do not
function.
• When disc/file is paused, SOUND menu cannot be displayed. Please switch SOUND when disc/file is being
played.
Setting
Options
Explanation
Sound Retriever
Off
A WMA or MP3 file is played with high sound quality. This is only
valid for files with the extension “.wma” or “.mp3”.
The effect depends on the file. Try different settings, and choose the
one providing the best effect.
Low
High
Equalizer
Add a variety of effects to the output sound. Select a mode that suits your personal tastes.
Off
Surround
News
This mode is suited to the news.
Gaming
This mode is suited to video games.
Movie
This mode is suited to movies.
Music
This mode is suited to music.
Off
Virtual 3D Min
Effect is minimum
Virtual 3D Mid
Effect is moderate
Virtual 3D Max
Effect is maximum
Virtual 3D Sound: Has the effect of
creating a 3D sound space.
5 Speaker Mode1
The sound from the front speakers will also be output by the rear
(BCS-727/BCS-323) speakers. This mode is valid in both 2 channel audio source and 5.1
channel audio source.
Dolby PL II Movie
Dolby Pro Logic II enables you to play stereo source on 5.1-channel.
(BCS-727/BCS-323) This mode is valid in 2 channel audio source.
Dolby PL II Music
(BCS-727/BCS-323)
Sound Wing Mode
(BCS-HF828 Only)
Off
HVT speakers make it possible to enjoy a broader-ranging sound.
Audio Sync
Adjust the delay between image and sound. Use
On
/
to adjust.
7
Other Operating
5 Speaker Mode2
The same sound will be output from the 5 speakers other than the
(BCS-727/BCS-323) sub woofer. This mode is valid in both 2 channel audio source and 5.1
channel audio source.
76
En
Advanced settings
Advanced settings
Operating the initial setup
screen
Changing the settings
1. When playback is stopped, display the
Home Menu screen.
HOME MENU.
Press
Chapter 8
2. Select and set Initial Setup.
Use / to select, then press ENTER.
3. Select the item and change the setting.
Use / / / to select, then press ENTER.
 Closing the Initial Setup screen
Press
HOME MENU or
RETURN.
Note
• The items that can be selected depend on the player’s status.
• In Options, the factory default settings are indicated in bold.
Display Setting
Advanced settings
Setting
Options
Explanation
TV Screen
16:9 Full
Select this when connecting to a wide (16:9) TV.
16:9 Normal
Select this when connected to a wide (16:9) TV. 4:3 pictures are displayed
with vertical black bars along the sides.
4:3 Pan&Scan
Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
video will be played with the left and right sides of the image cut off to display
on the 4:3 screen. (This function works if the disc is labeled for 4:3PS.)
4:3 Letterbox
Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
video will be played with black bands at the top and bottom.
Video Adjust
Sharpness
8
The quality of the playback picture can be adjusted according to the TV you are using (page 80).
High
Choose the level of sharpness.
Middle
Low
Video Mode
Standard
Choose the video output mode.
Vivid
Cinema
Custom
• CTI (Color Transient Improvement): Provides images with clearer color contours.
Noise Reduction
0
Choose the level of noise reduction.
1
2
3
Net Contents Mode
Off
On
Select this to automatically correct compressed video files on the network, a
disc or a USB device and play them with a more natural picture quality.
Advanced settings
77
En
Audio Output
Setting
Options
Explanation
DRC (Dynamic Range
Control)
Off
Select this to output audio signals without using the DRC function.
On
Select this to adjust the range between the loudest and softest sounds
(dynamic range) for playback at average volume. Use this when it is hard to
hear dialog or when watching movies at midnight.
Auto
Select to switch the DRC setting On/Off automatically according to the input
audio signal from the disc. This only affects Dolby TrueHD signals.
• This affects such audio signals as Dolby Digital, Dolby TrueHD, and Dolby Digital Plus.
• Depending on the disc, the effect may be weak.
Speaker Setup
Adjust the Trim (output level) and Delay (distance from viewers) of the speakers.
Please see "Adjust speaker settings" for more details (page 80).
HDMI
Test Tone
Output a test tone from the speakers.
Color Space
RGB
Select this to output the video signals as RGB signals. Choose this if the
colors seem too faint and the black seems too bright.
YCbCr
Select this to output the video signals as YCbCr 4:4:4 signals.
YCbCr 422
Select this to output the video signals as YCbCr 4:2:2 signals.
Full RGB
Select this to output the video signals as RGB signals. Choose this if the
colors seem too dense and all the dark colors are displayed in a uniform
black.
Auto
Select this to choose the resolution of the video signals output from the
HDMI OUT terminal automatically.
480I/576I
Output the video signals from the HDMI OUT terminal with the selected
resolution.
The resolution can be changed by pressing RESOLUTION, but Auto cannot be
selected.
Resolution
480P/576P
720P
1080I
1080P
HDMI Audio Out
HDMI Deep Color
HDMI 1080P 24Hz
HDMI 3D
3D Notice
Select this to output HDMI audio signals directly.
Select this to output HDMI audio signals converted to 2-channel audio
signals.
Reencode
When a BD containing secondary audio and interactive audio is played, the
two audio signals are mixed and converted to DTS audio for output.
Off
Select this when you do not want to output the audio signal from the HDMI
output terminal.
On
Select this to control the player with the remote control of the connected AV
device using an HDMI cable. Also refer to page 41.
Off
Select this when you do not want to control the player with the remote
control of the connected AV device using an HDMI cable.
30bits
Select this when outputting the video signals with 30-bit color.
36bits
Select this when outputting the video signals with 36-bit color.
Off
Select this when outputting the video signals with normal 24-bit color.
On
Select this when Resolution is set to Auto or 1080P and outputting 1080p/24
video signals to a TV compatible with 1080p/24.
Off
Select this when Resolution is set to 1080P and outputting 1080p/60 video
signals to a TV compatible with 1080p/60.
Auto
With 3D discs, the disc is played with 3D images.
Off
3D images are not played.
Yes
This sets whether or not to display the 3D notice when playing 3D images.
No
Advanced settings
Control
Bitstream
PCM
8
78
En
Advanced settings
Network
Setting
Options
IP Setting
Select this to set the IP address of the player and DNS server (page 80).
Proxy Server
Only set the proxy server if so instructed by your Internet service provider (page 81).
Information
Displays the values of the MAC address, IP address, subnet mask, default gateway, DNS server
(primary) and DNS server (secondary).
Connection Test
Select this to test the network connection (page 81).
Internet Connection
BD-Live Connection
DLNA
Interface
Explanation
Enable
Select this when connecting to the Internet.
Disable
Select this when not connecting to the Internet.
Permitted
All discs are allowed to connect to BD-LIVE.
Partial Permitted
Only discs whose safety has been confirmed are allowed to connect to BDLIVE.
Prohibited
No disc is allowed to connect to BD-LIVE.
Enable
Select this when connecting to DLNA server.
Disable
Select this when not connecting to DLNA server.
Ethernet
Select when using a LAN cable to connect to the network.
Wireless
Select when connecting wirelessly to the network.
Language
Wireless Setting
Perform settings for a wireless network connection. (page 47).
OSD
available languages Choose a language for the on-screen displays from the listed languages.
Audio
available languages Choose a language from the listed languages to set the default audio
* For some discs, it may
language for BD-ROM and DVD-Video playback.
not be possible to change
to the selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
available languages Choose a language from the listed languages to set the default subtitle
Subtitle
language for BD-ROM and DVD-Video playback.
* For some discs, it may
not be possible to change
to the selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Playback
Advanced settings
available languages Choose a language from the listed languages to set the default language for
Menu
* For some discs, it may
BD-ROM and DVD-Video menus.
not be possible to change
to the selected language.
On
Select this to display the angle mark on the TV screen (page 58).
Off
Select this if you do not want to display the angle mark on the TV screen.
On
Select this to display the PIP mark on the TV screen.
Off
Select this if you do not want to display the PIP mark on the TV screen.
On
Select this to display the secondary audio mark on the TV screen (page 62).
Off
Select this if you do not want to display the secondary audio mark on the TV
screen.
DivX(R) VOD DRM
Registration Code
Displays the player’s registration code required to play DivX VOD files (page 15).
Internet Setting
Permitted
Web contents can be watched without entering the password.
Angle Mark
PIP Mark
Secondary Audio Mark
8
Disc Auto Playback
Last Memory
PBC (Play Back Control)
Partial Permitted
The password must be entered to watch web contents.
Prohibited
No web contents can be watched.
On
Discs are played automatically after they are loaded.
Off
Loaded discs do not start playing automatically.
On
Select this to save the point at which you last stopped playback, even after
the disc tray is opened or you switch to the standby mode.
Off
Select this when you want to use only Continue Viewing Play (page 63).
On
Select this to play Video-CDs (version 2.0) compatible with PBC using the
disc menu.
Off
Select this to play Video-CDs (version 2.0) compatible with PBC without using
the disc menu.
Advanced settings
Setting
Options
79
En
Explanation
Setup Navigator
Start making the settings using the Setup Navigator menu. For details, see page 52.
Security
Register (change) the password for parental lock settings or for unlocking to play DVD-Videos with
the parental lock feature (page 82).
Change Password
Options
Parental Control
Change the player’s parental lock level (page 82).
Country Code
Change the Country/Area code (page 82).
Screen Saver
Off
The screen saver is not activated.
1 min
The screen saver will be activated if no operation has been performed for
more than one minute/two minutes/three minutes. Operating the remote
control can deactivate the screen saver.
2 min
3 min
Auto Power Off
Off
Select this if you do not want the power to turn off automatically.
10 min
The power will be automatically turned off if no operation has been performed
for more than 10 minutes/20 minutes/30 minutes.
20 min
30 min
Quick Start
Update
On
Select to shorten the required time to boot up.
Off
Select to perform normal bootup.
Disc
Select the method of software updating. (page 83)
USB Storage
Network
Load Default
Restore the settings to the factory default.
System Information
Check the system version number.
Disc Auto Update
On
Display the software update screen when the disc with the player’s update
file is loaded.
Off
The software update screen must be displayed manually. (page 83)
BUDA Information
Display and set up the BUDA data on the connected USB device.
BUDA
BUDA Setup
Microphone Setup
Vocal Cancel
Off
Select when not using Karaoke.
On
Select when using Karaoke.
Mic Volume
Select to adjust the volume of your microphone.
Use / to perform the adjustment on the mic volume adjustment screen.
Mic Echo
Select to adjust the level of microphone echo.
Use / to perform the adjustment on the mic echo adjustment screen.
Off
Select when you want Vocal Cancel off.
On
Select when you want Vocal Cancel on.
Advanced settings
Karaoke Setup
Karaoke Switch
8
80
En
Advanced settings
 Adjusting the video
 Setting the IP address
1. Select and set Display Setting d Video
Adjust d Next Screen.
Use / to select, then press ENTER.
1. Select and set Network d IP Setting d
Next Screen.
Use / to select, then press ENTER.
2. Select the item and change the setting.
Use / to select the item, then use /
to change the setting. Once the setting is
RETURN to close the
completed, press
settings screen.
2. Set IP address.
Use / / / to set the IP address of the
player or DNS server, then press ENTER.
yy Auto Set IP Address
Item
Description
Brightness
Select this to adjust the TV screen’s
brightness.
Contrast
Select this to adjust the TV screen’s
contrast.
Hue
Select this to adjust the color (green
and red) balance of the TV screen.
Saturation
Select this to adjust the TV screen’s
saturation.
 Adjust speaker settings
1. Select and set Audio Output d Speaker
Setup d Next Screen.
Use / / / to select, then press ENTER.
Advanced settings
8
2. A picture of speakers will be shown on
the screen. Select the speaker using
cursor and press ENTER.
3.Use / to select Trim or Delay and
then press ENTER.
4. Use cursor / to adjust the setting,
then press ENTER.
 Adjust speaker settings while listening
to a sound
1. Select and set Audio Output d Test
Tone d Next Screen.
Use / / / to select, then press ENTER.
2. A test tone will be output. The speakers
will switch automatically.
3. A picture of speakers will be shown
on the screen. Press ENTER when
the speaker you wish to adjust to is
focused.
4.Use / to select Trim or Delay and
then press ENTER.
5Use / to adjust the setting, then press
ENTER.
*1ms = 30 cm
On – The player’s IP address is obtained
automatically. Select this when using
a broadband router or broadband
modem that has a DHCP (Dynamic Host
Configuration Protocol) server function.
This player’s IP address will automatically
be allocated from the DHCP server.
Off – The player’s IP address must be set
manually. Use the number buttons (0 to 9)
to input the IP address, subnet mask and
default gateway.
Note
yy For information on the DHCP server function,
refer to the operating instructions for the
network device.
yy You may need to contact your Internet service
provider or network administrator when
inputting the IP address manually.
Advanced settings
81
 Setting the proxy server
 Testing the network connection
Only set the proxy server if so instructed by
your Internet service provider.
 Select and set Network d Connection
Test d Start.
Use / to select, then press ENTER.
[Network is OK.] is displayed once the
test is completed. If any other message is
displayed, check the connections and/or
settings (pages 46 and 80).
1. Select and set Network d Proxy Server
d Next Screen.
Use / to select, then press ENTER.
2. Select and set Use or Not use at Proxy
Server.
Use / to change, then press .
yy Use – Select this when using a proxy
server.
yy Not use – Select this when not using a
proxy server.
If you have selected Use, proceed to step 3.
3. Select and set Server Select Method.
Use / to change, then press .
yy IP Address – Input the IP address.
yy Server Name – Input the server name.
5. Input Port Number.
Press , then use the number buttons (0 to
9) to input the number.
6. Press ENTER to set.
 Displaying the network settings
 Select and set Network d Information
d Next Screen.
Use / to select, then press ENTER.
The MAC address, IP address, subnet mask,
default gateway and DNS server (primary
and secondary) settings are displayed.
When Auto Set IP Address is set to On, the
values obtained automatically are displayed.
Note
yy [0.0.0.0] is displayed when each IP address has
not been set.
 Changing to other language at
language setting
1. Select and set Language.
Use / to select, then press ENTER.
2. Select and set OSD, Audio, Subtitle or
Menu
Use / to select, then press ENTER.
3. Select and set the desired language.
Use / to select, then press ENTER.
Note
yy If a language not recorded on the BD/DVD
is set, one of the recorded languages is
automatically selected and played.
 Erasing data that has been added to
BDs and application data
Use this procedure to erase data that has
been added to BDs (data downloaded with
the BD-LIVE function and data used with
the BONUSVIEW function) and application
data.
Caution
yy Some time is required to erase the data.
yy Do not unplug the power cord while data is
being erased.
1. Select and set BUDA d BUDA Setup.
Use / to select, then press ENTER.
2. Select and set Fmt buda.
Press ENTER.
Advanced settings
4. Input IP Address or Server Name.
Use the number buttons (0 to 9) to input the
number if you select IP address in step 3.
Use / to move the cursor.
When Server Name is selected in step 3,
use the number buttons (0 to 9) to launch
the software keyboard. Now use / / /
to select characters and items, then press
ENTER to input.
En
8
82
En
Advanced settings
 Registering or Changing the password
Use this procedure to register or change
the code number required for the Parental
Lock settings.
About default password of this unit
The default password is [0000].
yy This unit might ask you to enter a
password when you change the
password.
yy If you reset this unit, your password is
simultaneously changed to the default
setting.
1. Select and set Security d Change
Password d Next Screen.
Use / to select, then press ENTER.
2. Input the password.
Use the number buttons (0 to 9) to input the
number, then press ENTER to set.
Use / to move the cursor.
3. Re-input the password.
Use the number buttons (0 to 9) to input the
number, then press ENTER to set.
Use / to move the cursor.
yy To change the password, input the
previously registered password, then
input the new password.
Advanced settings
8
Note
yy We recommend making a note of the password.
yy If you have forgotten the password, reset
the player to the factory default setting, then
register the password again (page 84).
 Changing the Parental Lock level for
viewing DVDs/BD-ROMs
Some DVD-Video discs containing scenes
of violence, for example, have Parental Lock
levels (check the indications on the disc’s
jacket or elsewhere). To restrict viewing
these discs, set the player’s level to the level
lower than the discs.
1. Select and set Security d Parental
Control d Next Screen.
Use / to select, then press ENTER.
2. Input the password.
Use the number buttons (0 to 9) to input the
number, then press ENTER to set.
Use / to move the cursor.
3. Change the level.
Use / to change, then press ENTER to
set.
Note
yy The level can be set to Off or between Level1
and Level8. When set to Off, viewing is not
restricted.
 Changing the Country/Area code
1. Select and set Security d Country
Code d Next Screen.
Use / tto select, then press ENTER.
2. Input the password.
Use the number buttons (0 to 9) to input the
number, then press ENTER to set.
Use / to move the cursor.
3. Change the country/area code.
Use / to change, then press ENTER to
set. Refer to page 85.
Advanced settings
Software updating
 Updating connecting to the Internet
The player’s software can be updated using
one of the methods shown below.
• Connecting to the Internet.
• Using a disc.
• Using a USB flash drive.
Product information on this player is provided
on the Pioneer website. Check the website
shown on page 10 for update and service
information on your Blu-ray disc player.
Caution
• Do not unplug the power cord or remove the USB
flash drive/disc during software updating. Also, do
not reboot by pressing the u STANDBY/ON button
for 5 seconds or longer. Otherwise, the updating
will be aborted and malfunction may occur with
the player.
• There are two processes for software updating,
downloading and updating. Both processes may
take a certain period of time.
• Other operations are defeated during software
updating. Furthermore, updating process cannot
be canceled.
83
En
Note
yy Depending on the Internet connection
conditions, downloading may take a long time.
yy Steps 1 to 5 are the operations performed by
the user (they are intended to download the
software from the Internet).
yy Steps 6 to 8 are the operations performed
(automatically) by the player (they are intended
to update the software).
1. Connect to the Internet.
2. When playback is stopped, display the
Home Menu screen.
HOME MENU.
Press
3. Select and set Initial Setup.
Use / to select, then press ENTER.
4. Select and set Options d Update d
Network d Start.
Use / to select, then press ENTER.
5. Select and set Start.
Press ENTER.
7. Updating starts.
yy Software updating may take a certain
period of time.
8. Updating completes.
This unit automatically restarts.
Advanced settings
6. Downloading of the software start.
The software download status is displayed
on the screen.
yy Depending on the Internet connection
conditions, software downloading may
take a certain period of time.
8
84
En
Advanced settings
 Updating using a USB flash drive/disc
Note
Advanced settings
yy When an update file is provided on the Pioneer
website, use your computer to download it
onto a USB flash drive or disc. Carefully read
the instructions on downloading update files
provided on the Pioneer website.
yy Store the update file in the root directory of the
USB flash drive or disc. Do not store it within a
folder.
yy Do not put any files other than the update file
on the USB flash drive or disc.
yy To update using a disc, use a CD-R or CD-RW
disc.
yy The player supports USB flash drive formatted
in FAT32/16. When formatting a USB flash
drive on your computer, do so with the settings
below.
–– File system: FAT32
–– Allocation unit size: Default allocation size
yy Only store the most recent update file on the
USB flash drive or disc.
yy Do not use a USB extension cable to connect
a USB flash drive to the player. Using a USB
extension cable may prevent the player from
performing correctly.
yy Steps 1 to 5 are the operations performed by
the user.
yy Steps 6 to 7 are the operations performed
(automatically) by the player (they are intended
to update the software).
1. Plug in the USB flash drive or load the
disc on which the update file is stored.
2. When playback is stopped, display the
Home Menu screen.
HOME MENU.
Press
3. Select and set Initial Setup.
Use / to select, then press ENTER.
8
4. Select and set Options d Update d
Disc or USB Storage d Start.
Use / to select, then press ENTER.
5. Select and set Yes.
Use / / / to select Yes, then press
ENTER.
6. Updating starts.
yy Software updating may take a certain
period of time.
7. Updating completes.
Restoring all the settings to
the factory default settings
1. Check that the player’s power is turned
on.
2. When playback is stopped, display the
Home Menu screen.
HOME MENU.
Press
3. Select and set Initial Setup.
Use / to select, then press ENTER.
4. Select and set Options d Load Default
d Next Screen.
Use / to select, then press ENTER.
5. Select and set OK.
Use / to select, then press ENTER.
6.Press  STANDBY/ON to turn off the
power.
7.Press  STANDBY/ON to turn on the
power.
Note
yy After restoring all the settings to the factory
default settings, use Setup Navigator to reset
the player (page 52).
Advanced settings
85
En
Language code table and
country/area code table
 Language code table
Language name, language code, input code
French, fr/fra, 0618
Galician, gl/glg, 0712
Georgian, ka/kat, 1101
German, de/deu, 0405
Greek, el/ell, 0512
Guarani, gn/grn, 0714
Gujarati, gu/guj, 0721
Hausa, ha/hau, 0801
Hebrew, iw/heb, 0923
Hindi, hi/hin, 0809
Hungarian, hu/hun, 0821
Icelandic, is/isl, 0919
Indonesian, in/ind, 0914
Interlingua, ia/ina, 0901
Interlingue, ie/ile, 0905
Inupiaq, ik/ipk, 0911
Irish, ga/gle, 0701
Italian, it/ita, 0920
Japanese, ja/jpn, 1001
Javanese, jw/jav, 1023
Kalaallisut, kl/kal, 1112
Kannada, kn/kan, 1114
Kashmiri, ks/kas, 1119
Kazakh, kk/kaz, 1111
Kinyarwanda, rw/kin, 1823
Kirghiz, ky/kir, 1125
Korean, ko/kor, 1115
Kurdish, ku/kur, 1121
Lao, lo/lao, 1215
Latin, la/lat, 1201
Latvian, lv/lav, 1222
Lingala, ln/lin, 1214
Lithuanian, lt/lit, 1220
Macedonian, mk/mkd, 1311
Malagasy, mg/mlg, 1307
Malay, ms/msa, 1319
Malayalam, ml/mal, 1312
Maltese, mt/mlt, 1320
Maori, mi/mri, 1309
Marathi, mr/mar, 1318
Mongolian, mn/mon, 1314
Moldavian, mo/mol, 1315
Nauru, na/nau, 1401
Nepali, ne/nep, 1405
Norwegian, no/nor, 1415
Occitan, oc/oci, 1503
Oriya, or/ori, 1518
Oromo, om/orm, 1513
Panjabi, pa/pan, 1601
Persian, fa/fas, 0601
Polish, pl/pol, 1612
Portuguese, pt/por, 1620
Pushto, ps/pus, 1619
Quechua, qu/que, 1721
Romanian, ro/ron, 1815
Romansch, rm/roh, 1813
Rundi, rn/run, 1814
Russian, ru/rus, 1821
Samoan, sm/smo, 1913
Sango, sg/sag, 1907
Sanskrit, sa/san, 1901
Scottish Gaelic, gd/gla, 0704
Serbian, sr/srp, 1918
Serbo-Croatian, sh/---, 1908
Shona, sn/sna, 1914
Sindhi, sd/snd, 1904
Sinhalese, si/sin, 1909
Slovak, sk/slk, 1911
Slovenian, sl/slv, 1912
Somali, so/som, 1915
Sotho, Southern, st/sot, 1920
Spanish, es/spa, 0519
Sundanese, su/sun, 1921
Swahili, sw/swa, 1923
Swati, ss/ssw, 1919
Swedish, sv/swe, 1922
Tagalog, tl/tgl, 2012
Tajik, tg/tgk, 2007
Tamil, ta/tam, 2001
Tatar, tt/tat, 2020
Telugu, te/tel, 2005
Thai, th/tha, 2008
Tibetan, bo/bod, 0215
Tigrinya, ti/tir, 2009
Tonga (Tonga Islands), to/ton, 2015
Tsonga, ts/tso, 2019
Tswana, tn/tsn, 2014
Turkmen, tk/tuk, 2011
Turkish, tr/tur, 2018
Twi, tw/twi, 2023
Ukrainian, uk/ukr, 2111
Urdu, ur/urd, 2118
Uzbek, uz/uzb, 2126
Vietnamese, vi/vie, 2209
Volapük, vo/vol, 2215
Welsh, cy/cym, 0325
Western Frisian, fy/fry, 0625
Wolof, wo/wol, 2315
Xhosa, xh/xho, 2408
Yiddish, ji/yid, 1009
Yoruba, yo/yor, 2515
Zulu, zu/zul, 2621
Luxembourg, lu, 1221
Macedonia, the Former
Yugoslav Republic of, mk, 1311
Malaysia, my, 1325
Malta, mt, 1320
Mexico, mx, 1324
Moldova, Republic of, md, 1304
Monaco, mc, 1303
Montserrat, ms, 1319
Netherlands, nl, 1412
New Zealand, nz, 1426
Norway, no, 1415
Pakistan, pk, 1611
Peru, pe, 1605
Philippines, ph, 1608
Poland, pl, 1612
Portugal, pt, 1620
Puerto Rico, pr, 1618
Romania, ro, 1815
Russian Federation, ru, 1821
Saint Kitts and Nevis, kn, 1114
Saint Lucia, lc, 1203
Saint Vincent and the
Grenadines, vc, 2203
San Marino, sm, 1913
Singapore, sg, 1907
Slovakia, sk, 1911
Slovenia, si, 1909
Spain, es, 0519
Suriname, sr, 1918
Sweden, se, 1905
Switzerland, ch, 0308
Taiwan, Province of China, tw,
2023
Tajikistan, tj, 2010
Thailand, th, 2008
Trinidad and Tobago, tt, 2020
Tunisia, tn, 2014
Turkey, tr, 2018
Turkmenistan, tm, 2013
Turks and Caicos Islands, tc,
2003
Ukraine, ua, 2101
United Kingdom, gb, 0702
United States, us, 2119
Uruguay, uy, 2125
Uzbekistan, uz, 2126
Venezuela, ve, 2205
Virgin Islands, British, vg, 2207
 Country/area code table
Country/Area name, Country/Area code, input code
Anguilla, ai, 0109
Antigua and Barbuda, ag, 0107
Argentina, ar, 0118
Armenia, am, 0113
Australia, au, 0121
Austria, at, 0120
Azerbaijan, az, 0126
Bahamas, bs, 0219
Barbados, bb, 0202
Belarus, by, 0225
Belgium, be, 0205
Belize, bz, 0226
Bermuda, bm, 0213
Brazil, br, 0218
Bulgaria, bg, 0207
Canada, ca, 0301
Cayman Islands, ky, 1125
Chile, cl, 0312
China, cn, 0314
Colombia, co, 0315
Croatia, hr, 0818
Cyprus, cy, 0325
Czech Republic, cz, 0326
Denmark, dk, 0411
Dominica, dm, 0413
Dominican Republic, do, 0415
Estonia, ee, 0505
Finland, fi, 0609
France, fr, 0618
Georgia, ge, 0705
Germany, de, 0405
Greece, gr, 0718
Greenland, gl, 0712
Grenada, gd, 0704
Guyana, gy, 0725
Haiti, ht, 0820
Hong Kong, hk, 0811
Hungary, hu, 0821
Iceland, is, 0919
India, in, 0914
Indonesia, id, 0904
Ireland, ie, 0905
Israel, il, 0912
Italy, it, 0920
Jamaica, jm, 1013
Japan, jp, 1016
Kazakhstan, kz, 1126
Korea, Republic of, kr, 1118
Kyrgyzstan, kg, 1107
Latvia, lv, 1222
Liechtenstein, li, 1209
Lithuania, lt, 1220
Advanced settings
Abkhazian, ab/abk, 0102
Afar, aa/aar, 0101
Afrikaans, af/afr, 0106
Albanian, sq/sqi, 1917
Amharic, am/amh, 0113
Arabic, ar/ara, 0118
Armenian, hy/hye, 0825
Assamese, as/asm, 0119
Aymara, ay/aym, 0125
Azerbaijani, az/aze, 0126
Bashkir, ba/bak, 0201
Basque, eu/eus, 0521
Belarusian, be/bel, 0205
Bengali, bn/ben, 0214
Bihari, bh/bih, 0208
Bislama, bi/bis, 0209
Breton, br/bre, 0218
Bulgarian, bg/bul, 0207
Burmese, my/mya, 1325
Catalan, ca/cat, 0301
Central Khmer, km/khm, 1113
Chinese, zh/zho, 2608
Corsican, co/cos, 0315
Croatian, hr/hrv, 0818
Czech, cs/ces, 0319
Danish, da/dan, 0401
Dutch, nl/nld, 1412
Dzongkha, dz/dzo, 0426
English, en/eng, 0514
Esperanto, eo/epo, 0515
Estonian, et/est, 0520
Finnish, fi/fin, 0609
Fijian, fj/fij, 0610
Faroese, fo/fao, 0615
8
86
En
Troubleshooting
Chapter 9
Troubleshooting
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something
wrong with this component, check the points below. Sometimes the trouble may lie in another
component. Inspect the other components and electrical appliances being used. If the trouble
cannot be rectified even after checking the points below, ask your nearest Pioneer authorized
service center or your dealer to carry out repair work.
Picture
Problem
No picture is displayed
or the picture is not
displayed properly.
No picture is displayed
or picture is not output
in high definition when
playing BDs.
yyPicture is disturbed
during playback.
yyPicture is dark.
Troubleshooting
9
Check
Is the video cable properly
connected?
Remedy
yyConnect the cable properly according to the connected devices (page
41).
yyDisconnect the cable (video/audio cable or HDMI cable), then reinsert
it firmly and all the way in.
If the cable is damaged, replace it with a new one.
Read the operating instructions for the connected components and
switch to the proper input.
Press RESOLUTION to switch the video resolution output from the HDMI
OUT terminal (page 18).
1080p or Deep Color video signals may not be output properly,
depending on the HDMI cable being used or the player’s settings. If you
wish to output the video signals with 1080p or Deep Color, connect the
TV using a High Speed HDMI®/™ Cable without a built-in equalizer, then
reset the player using the Setup Navigator (page 52).
Is the video cable damaged?
Is the input setting on the
connected TV right?
Is the output video resolution
properly set?
yyIs the player connected with
an HDMI cable other than a
High Speed HDMI®/™ Cable
(with a Standard HDMI®/™
cable)?
yyAre you using an HDMI cable
with a built-in equalizer?
Is a DVI device connected?
The picture may not be displayed properly if a DVI device is connected.
Is Color Space properly set?
Change the Color Space setting (page 77).
With some discs, it may not be possible to output the video signals from
the VIDEO output terminal. In this case, connect using an HDMI cable
(page 41).
yyThis player supports Rovi analog copy protection technology. With
some TVs (such as with built-in video deck), the picture will not be
displayed properly when the copy protected DVD title is played. This is
not a malfunction.
yyIf the player and TV are connected via a DVD recorder/video deck,
etc., the picture will not be displayed properly due to analog copy
protection. Connect the player and TV directly.
Is the TV’s aspect ratio properly Read the operating instructions for the TV and set the TV’s aspect ratio
yyPicture is stretched.
set?
properly.
yyPicture is cropped.
Set TV Screen properly (page 76).
yyAspect ratio cannot be Is TV Screen properly set?
switched.
When video signals with a resolution of 1080/50i, 1080/50p, 720/50p,
1080/24p, 1080/60i, 1080/60p or 720/60p are being output from the
HDMI OUT terminal, they may be output with an aspect ratio of 16:9
even if TV Screen is set to 4:3 Pan&Scan (page 76).
Picture is interrupted.
The picture may be interrupted when the resolution of the recorded
video signal switches. Press RESOLUTION to select a setting other than
Auto (page 77).
Blu-ray 3D disc playback
yyConnect the player to your TV with HDMI cable (High Speed HDMI®/™
does not output 3D views.
Cable).
yyYour TV may not support “HDMI 3D mandatory format”.
Troubleshooting
87
En
Sound
Problem
yyNo sound is output.
yySound is not output
properly.
Multi-channel sound is
not output.
No sound from surround
or center speaker.
No sound from the subwoofer.
Excessive noise during
radio reception.
Check
yyIs the disc played back in
slow motion?
yyIs the disc played back in fast
forward or fast reverse?
Are the cables properly
connected?
Remedy
No sound is output during slow motion play and forward and reverse
scanning.
Check
Is the disc one that is playable
on this player?
Is the file one that is playable
on this player?
Remedy
Check whether the disc is one that can be played on this player
(page 11).
yyCheck whether the file is one that can be played on this player (page 15).
yyCheck whether or not the file is damaged.
It may not be possible to play scratched discs.
Clean the disc (page 95).
The disc may be warped and unplayable.
yyConnect the cable properly according to the connected devices
(page 41).
yyInsert the cable firmly and all the way in.
Is the audio cable damaged?
If the cable is damaged, replace it with a new one.
Is Audio Output properly set? Set Audio Output properly, according to the connected device
(page 77).
Are the connected components Read the operating instructions for the connected components and
properly set?
check the volume, input, speaker settings, etc.
Is multi-channel sound
Use the menu screen or AUDIO to switch the disc’s sound to multiselected?
channel.
yyCheck to confirm that the speakers are connected properly.
yyCheck the volume setting in the Speaker Setup for Audio Menu menu
(page 77).
When the audio signal being played has no bass component, no sound
will come from the sub-woofer.
Check the volume setting in the Speaker Setup for Audio Menu (page 77).
yyConnect an antenna and set to the best reception position.
yySet an FM antenna outside the house.
yyTurn power off the electric devices that may be causing the noise or
move these devices away from this unit.
Playback
Problem
yyDisc does not play.
yyDisc tray opens
automatically.
Is the disc scratched?
Is the disc dirty?
Is there a piece of paper or
sticker attached to the disc?
Is the region number correct?
Picture freezes and the
front panel and remote
control buttons stop
working.
The subtitles cannot be
switched.
After a disc is inserted,
Are there too many files
Loading stays displayed recorded on the disc?
and playback does not
start.
(g) is displayed in file
names, etc.
A message indicating low
memory appears while
playing a BD-ROM disc.
yySet the disc with the printed side facing up.
yySet the disc properly in the depression in the disc tray.
See page 13 for the region numbers of discs that can be played on this
player.
yyPress (g) STOP to stop playback, then restart playback.
yyIf the playback cannot be stopped, press u STANDBY/ON on the
player’s front panel to turn off the power, then turn the power back on.
yyPress  STANDBY/ON on the player for more than 5 seconds. The unit
reboots, and the operation becomes possible.
The subtitles cannot be switched for discs recorded on a DVD or BD
recorder.
When a disc on which files are recorded is inserted, depending on the
number of files recorded on the disc, loading may take several dozen
minutes.
The characters that cannot be displayed on this player are displayed in
(g).
yyConnect a USB device (page 51).
yyErase the data stored on the connected USB device from BUDA Setup
(page 81).
Troubleshooting
Is the disc properly set in the
disc tray?
9
88
En
Troubleshooting
Control function
Problem
Check
Control function does not Is the HDMI cable properly
work.
connected?
Is the HDMI cable you are
using a High Speed HDMI®/™
Cable?
Is this player connected to the
TV using an HDMI cable to
watch the picture?
Does the connected device
support the Control function?
Is Control set to On on the
connected device?
Remedy
To use the Control function, connect the Flat Screen TV to the HDMI
OUT terminal (page 41).
Use a High Speed HDMI®/™ Cable. The Control function may not work
properly if an HDMI cable other than a High Speed HDMI®/™ Cable is
used.
If video signals are being output from a terminal other than the HDMI
OUT terminal, the Control function does not work. Connect to the TV
using an HDMI cable (page 41).
yyThe Control function will not work with devices of other brands that
do not support the Control function, even when connected using an
HDMI cable.
yyThe Control function will not work if devices that do not support the
Control function are connected between the Control-compatible
device and the player.
yySee page 16.
yyEven when connected to a Pioneer product compatible with the
Control function, some of the functions may not work.
Also refer to the operating instructions for the connected device.
Set Control to On on the connected device. The Control function
operates when Control is set to On for all devices connected to the
HDMI OUT terminal.
Once connections and settings of all the devices are finished, be sure
to check that the player’s picture is output to the Flat Screen TV. (Also,
check after changing the connected devices and connecting and/or
disconnecting HDMI cables.) If the player’s picture is not being output
to the Flat Screen TV, the Control function may not work properly.
For details, refer to the operating instructions of the connected device.
Network
Troubleshooting
Problem
Check
yyBD-LIVE function
(connection to the
Internet) cannot be
used.
yy"No valid id file found!"
is displayed when I try
to update the software.
Software updating is slow.
A message other than
"Networks is OK."
is displayed when
Connection Test is
performed.
Is "Network is FAILED."
displayed?
9
Is the Ethernet hub (or router
with a hub functionality)
operating properly?
Cannot access to the
component or PC
connected via network.
Internet security software
is currently installed in the
connected component.
The audio component on
the network which has been
switched off is switched on.
Remedy
Perform Connection Test (page 81). If "Networks is OK." is displayed,
check the proxy server settings (page 81). Also, there may be a problem
with the Internet connection. Contact your Internet service provider.
Depending on the Internet connection and other conditions, some time
may be required to update the software.
yyCheck that this player and the Ethernet hub (or router with a hub
functionality) are properly connected.
yyIf the IP address is obtained using the DHCP server function, check
the setting is correct at the Information (page 78). For details on the
DHCP server function, see the operating instructions for the Ethernet
hub (or router with a hub functionality).
yySet the IP address manually.
yyCheck the operation and settings of the DHCP server function of the
Ethernet hub (or router with hub functionality). For details on the
DHCP server function, see the operating instructions for the Ethernet
hub (or router with a hub functionality).
yyIf this player has been set manually, reset the IP address of this player
or other components.
yyCheck the settings and operation the Ethernet hub (or router with a
hub functionality). For details, see the operating instructions for the
Ethernet hub.
yyReboot the Ethernet hub (or router with a hub functionality).
There are cases where a component with Internet security software
installed cannot be accessed.
Switch on the audio component on the network before switching on
this unit.
Troubleshooting
89
En
Problem
Troubleshooting
Check
Remedy
The component connected to If the client is automatically authorized, you need to enter the
the network is not properly set. corresponding information again. Check whether the connection status
is set to “Do not authorize”.
There are no playable audio
Check the audio files stored on the component connected to the
files on the component
network.
connected to the network.
Check whether the component is properly connected to this unit or the
Playback does not start. The component is currently
disconnected from this unit or power supply.
the power supply.
The PC is not properly
The corresponding IP address Switch on the built-in DHCP server function of your router, or set up the
operated.
is not properly set.
network manually according to your network environment.
The IP address is being
The automatic configuration process takes time. Please wait.
automatically configured.
The audio files stored
Windows Media Player 11 or
Install Windows Media Player 11 or Windows Media Player 12 on your
on components on the
Windows Media Player 12 is not PC.
network, such as a PC,
currently installed on your PC.
cannot be played back.
Audio files were recorded in
Play back audio files recorded in MP3, WAV (LPCM only), MPEG-4 AAC,
formats other than MP3, WAV FLAC, or WMA. Note that some audio files recorded in these formats
(LPCM only), MPEG-4 AAC,
may not be played back on this unit.
FLAC, and WMA.
Audio files recorded in MPEG-4 Audio files recorded in MPEG-4 AAC or FLAC cannot be played back
AAC or FLAC are being played on Windows Media Player 11 or Windows Media Player 12. Try using
back on Windows Media Player another server. Refer to the operation manual supplied with your server.
11 or Windows Media Player 12.
The component connected
Check whether the component is affected by special circumstances or
to the network is not properly
is in the sleep mode. Try rebooting the component if necessary.
operated.
The component connected to Try changing the settings for the component connected to the network.
the network does not permit
file sharing.
The folder stored on the
Check the folder stored on the component connected to the network.
component connected to the
network has been deleted or
damaged.
Network connections could be Check the computer’s network settings, security settings, etc.
restricted due to the
computer’s network settings,
security settings, etc.
Cannot access Windows In case of Windows Media Player Instead of logging onto the domain, log onto the local machine.
Media Player 11 or
11: You are currently logged onto
Windows Media Player 12. the domain through your PC
with Windows XP or Windows
Vista installed.
In case of Windows Media Player
12: You are currently logged onto
the domain through your PC
with Windows 7 installed.
Audio playback is
The audio file currently being
yyCheck whether the audio file was recorded in a format supported by
undesirably stopped or
played back was not recorded
this unit.
disturbed.
in a format playable on this
yyCheck whether the folder has been damaged or corrupted.
unit.
Even audio files listed as playable on this unit may sometimes not be
played back or displayed.
The LAN cable is currently
Connect the LAN cable properly.
disconnected.
There is heavy traffic on the
Use 100BASE-TX to access the components on the network.
network with the Internet being
accessed on the same network.
There is a connection routed
yyThere may be a shortage of bandwidth on the 2.4 GHz band used by
through a wireless LAN on the
the wireless LAN. Make wired LAN connections not routed through a
same network.
wireless LAN.
yyInstall away from any devices emitting electromagnetic waves on the
2.4 GHz band (microwave ovens, game consoles, etc.). If this does not
solve the problem, stop using other devices that emit electromagnetic
waves.
9
90
En
Troubleshooting
Others
Problem
Power does not
turned on.
Power turns OFF without
warning
The player’s power turns
off automatically.
The player’s power turns
on automatically.
Check
Is the power cord properly
connected?
Is Control set to On?
Is Control set to On?
Cannot be operated with
the remote control.
Are you operating the remote
control from a point too far
away from the player?
Are the batteries dead?
Settings I have made have yyHave you disconnected the
been cleared.
power cord while the player’s
power was on?
yyHas there been a power
failure?
USB (external storage)
Is the USB device properly
device does not work with connected?
this player properly.
Is the USB device connected
via an extension cable?
Is the external storage device
connected to the USB port via
a memory card reader or USB
hub?
Does the external storage
device contain multiple
partitions?
Troubleshooting
9
Display window is dark
Remedy
yyPlug the power cord securely into the power outlet.
yyUnplug the power cord, wait several seconds, then plug the power
cord back in.
Auto Power Off is set. The display will move to screen saver mode in 1
minutes and will automatically power OFF in about 30 minutes.
The player’s power may turn off together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn off when the TV’s power is turned off, set Control to Off
(page 77).
The player’s power may turn on together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn on when the TV’s power is turned on, set Control to Off
(page 77).
Operate from within 7 m of the remote control sensor.
Replace the batteries (page 10).
Always press u STANDBY/ON on the player’s front panel or u
STANDBY/ON on the remote control, check that POWER OFF has turned
off from the player’s front panel display and wait for more than 10
seconds before disconnecting the power cord. Be particularly careful
when the power cord is connected to the AC outlet on another device
because the player turns off in conjunction with the device.
yyTurn the player’s power off, then turn the power back on.
yyTurn the player’s power off, then reconnect the external storage device
(page 51).
Do not use an extension cable. The player may not work properly with it.
External storage device may not work if connected to the USB port via a
memory card reader or USB hub.
External storage devices may not be recognized if they contain multiple
partitions.
Some external storage devices may not operate.
Is the external storage device
Turn the player’s power off, then disable the write-protection.
write-protected?
Is the external storage device’s Only external storage devices with a FAT16 or FAT32 file system can be
file system FAT16 or FAT32?
used.
Turn the player’s power off, then turn the power back on.
Press the DIMMER on the remote and select the desired display
brightness.
Appendix
91
En
Chapter 10
Appendix
Specifications
General for BCS-727/BCS-323
Power requirements
AC 110 V to 240 V, 50 Hz/60 Hz
Power consumption
190 W (In Standby mode: Less than 0.5 W)
Dimensions (W x H x D)
Approx. 430 mm x 345 mm x 62 mm
Net Weight (Approx.)
3.4 kg
Operating temperature
5 °C to 35 °C
Operating humidity
5 % to 85 %
General for BCS-HW929/BCS-HF828/BCS-SB626/BCS-FS525
Power requirements
AC 110 V to 240 V, 50 Hz/60 Hz
Power consumption
105 W (In Standby mode: Less than 0.5 W)
Dimensions (W x H x D)
Approx. 430 mm x 345 mm x 62 mm
Net Weight (Approx.)
3.3 kg
Operating temperature
5 °C to 35 °C
Operating humidity
5 % to 85 %
Inputs/Outputs
VIDEO OUT
1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI IN/OUT (video/audio)
19 pin (HDMI®/™ Connector)
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
3 V (p-p), Optical jack x 2 (48 kHz, 96 kHz sampling)
PORTABLE IN
0.5 Vrms (3.5 mm stereo jack)
ADAPTER PORT
5 V, 100 mA
MIC
Mic jack x 1
USB
4 pin A Type x 2
iPod
12 V, 500 mA
Appendix
ANALOG AUDIO IN
DIGITAL IN (OPTICAL)
Tuner
FM Tuning Range
87.5 MHz to 108.0 MHz
Antenna input
75 Ω unbalanced
10
92
En
Appendix
Amplifier for BCS-727/BCS-323
Power output (RMS) THD 30 %
Total
1100 W
Front
150 W × 2 (4 Ω)
Center
250 W (3 Ω)
Rear
150 W × 2 (4 Ω)
Sub-Woofer
250 W (3 Ω)
Amplifier for BCS-HW929/BCS-HF828/BCS-SB626/BCS-FS525
Power output (RMS) THD 30 %
Total
550 W
Front
150 W × 2 (4 Ω)
Sub-Woofer
250 W (3 Ω)
System
Laser
Semiconductor laser
Signal system
Standard PAL/NTSC colour TV system
LAN port
Ethernet jack x 1, 10BASE-T / 100BASE-TX
Wireless LAN (internal
antenna)
Integrated IEEE 802.11n (2.4 GHz band) wireless networking
access, compatible with 802.11b/g Wi-Fi networks.
Bus Power Supply (USB)
DC 5 V
500 mA
Speakers for BCS-727
S-BD421
• Front (Left/ Right)
Type
2 Way
Net Dimensions
(W x H x D)
250 mm x 1110 mm x 250 mm
Impedance Rated
4Ω
Net Weight
3.5 kg
• Surround speaker (Left/ Right)
Appendix
10
Type
1 Way
Net Dimensions
(W x H x D)
250 mm x 1110 mm x 250 mm
Impedance Rated
4Ω
Net Weight
3.4 kg
Type
1 Way
Net Dimensions
(W x H x D)
230 mm x 80 mm x 90 mm
Impedance Rated
3Ω
Net Weight
0.7 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
• Center speaker
• Subwoofer
Appendix
93
En
Speakers for BCS-323
S-BD121
• Front/Surround speaker (Left/Right)
Type
1 Way
Net Dimensions
(W x H x D)
95 mm x 80 mm x 90 mm
Impedance Rated
4Ω
Net Weight
0.3 kg
Type
1 Way
Net Dimensions
(W x H x D)
230 mm x 80 mm x 90 mm
Impedance Rated
3Ω
Net Weight
0.7 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
• Center speaker
• Subwoofer
Speakers for BCS-HW929
S-BD921HW
• Front speaker
Type
2 Way
Net Dimensions
(W x H x D)
900 mm x 66 mm x 93 mm
Impedance Rated
4Ω
Net Weight
1.6 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
S-BD921SW
• Subwoofer
Speakers for BCS-HF828
S-BD821HF
• Front speaker (Left/Right)
Type
2 Way
Impedance Rated
4Ω
Net Weight
0.4 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
100 mm x 225 mm x 100 mm
(side putting)
Appendix
207 mm x 100 mm x 100 mm
(lengthwise putting)
Net Dimensions
(W x H x D)
• Subwoofer
10
94
En
Appendix
Speakers for BCS-SB626
S-BD621FS
• Front speaker
Type
1 Way
Net Dimensions
(W x H x D)
800 mm x 100 mm x 88 mm
Impedance Rated
4Ω
Net Weight
1.9 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
S-BD921SW
• Subwoofer
Speakers for BCS-FS525
S-BD521FS
• Front speaker (Left/ Right)
Type
Impedance Rated
1 Way
Net Dimensions
(W x H x D)
380 mm x 97 mm/
87 mm x 110 mm
(lengthwise putting)
110 mm x 412 mm x 110 mm
(side putting)
4Ω
Net Weight
0.9 kg
Type
1 Way
Net Dimensions
(W x H x D)
130.5 mm x 420 mm x 375 mm
Impedance Rated
3Ω
Net Weight
4.4 kg
• Subwoofer
• Design and specifications are subject to change without notice.
Appendix
10
Appendix
Maintenance
Notes on discs
Handling the unit
Handling discs
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit,
for maximum protection, re-pack the unit as it
was originally packed at the factory.
95
En
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints
do not get on the surface. Never stick paper or
tape on the disc.
Storing discs
• Do not use volatile liquids such as insecticide
spray near the unit.
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed
to direct sunlight.
• Wiping with strong pressure may damage
the surface.
Cleaning discs
• Do not leave rubber or plastic products in
contact with the unit for a long period of
time.
Fingerprints and dust on the disc can cause
poor picture quality and sound distortion.
Before playing, clean the disc with a clean
cloth. Wipe the disc from the center to out.
Keeping the exterior surfaces clean
Cleaning the unit
To clean the player, use a soft, dry cloth. If
the surfaces are extremely dirty, use a soft
cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as
alcohol, benzine, or thinner, as these might
damage the surface of the unit.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available
cleaners, or anti-static spray intended for older
vinyl records.
Maintaining the unit
The unit is a high-tech, precision device. If
the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality could be
diminished. For details, please contact your
nearest authorized service center.
Appendix
10
96
En
Appendix
Important Information
Relating to Network
Services
All information, data, documents,
communications, downloads, files, text,
images, photographs, graphics, videos,
webcasts, publications, tools, resources,
software, code, programs, applets, widgets,
applications, products and other content
(“Content”) and all services and offerings
(“Services”) provided or made available by
or through any third party (each a “Service
Provider”) is the sole responsibility of the
Service Provider from whom it originated.
The availability of and access to Content and
Services furnished by the Service Provider
through the PIONEER Device are subject
to change at any time, without prior notice,
including, but not limited to the suspension,
removal or cessation of all or any part of the
Content or Services.
Should you have any inquiry or problem related
to the Content or Services, you may refer to
the Service Provider’s website for the most
up-to-date information. PIONEER is neither
responsible nor liable for customer service
related to the Content and Services. Any
question or request for service relating to the
Content or Services should be made directly to
the respective Content and Service Providers.
Please note that PIONEER is not responsible
for any Content or Services provided by the
Service Provider or any changes to, removal of,
or cessation of such Content or Services and
does not warrant or guaranty the availability of
or access to such Content or Services.
Appendix
10
© 2012 PIONEER CORPORATION.
All rights reserved.
Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC
Manufacturer:
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku,
Kawasaki-shi, Kanagawa
212-0031, Japan
EU Representative’s:
Pioneer Europe NV
Haven 1087, Keetberglaan 1,
9120 Melsele, Belgium
http://www.pioneer.eu
[*] XV-BD421W, XV-BD121W,
XV-BD921FSW, XV-BD821FSW,
XV-BD621FSW, XV-BD521FSW
English:
Dansk:
Suomi:
Deutsch:
Nederlands:
Ελληνικά:
Français:
Italiano:
Svenska:
Español:
Hereby, Pioneer, declares that this [*]
is in compliance with the essential
requirements and other relevant
provisions of Directive 1999/5/EC.
Pioneer vakuuttaa täten että [*]
tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen
mukainen.
Hierbij verklaart Pioneer dat het toestel
[*] in overeenstemming is met de
essentiële eisen en de andere
relevante bepalingen van richtlijn
1999/5/EG
Par la présente Pioneer déclare que
l’appareil [*] est conforme aux
exigences essentielles et aux autres
dispositions pertinentes de la directive
1999/5/CE
Härmed intygar Pioneer att denna [*]
står I överensstämmelse med de
väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår
av direktiv 1999/5/EG.
Undertegnede Pioneer erklærer herved,
at følgende udstyr [*] overholder de
væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF
Hiermit erklärt Pioneer, dass sich
dieses [*] in Übereinstimmung mit den
grundlegenden Anforderungen und den
anderen relevanten Vorschriften der
Richtlinie 1999/5/EG befindet". (BMWi)
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Pioneer ΔΗΛΩΝΕΙ
ΟΤΙ [*] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ
ΟΔΗΓΙΑΣ 1999/5/ΕΚ
Con la presente Pioneer dichiara che
questo [*] è conforme ai requisiti
essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva
1999/5/CE.
Por medio de la presente Pioneer
declara que el [*] cumple con los
requisitos esenciales y cualesquiera
otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE
Português:
Pioneer declara que este [*] está
conforme com os requisitos essenciais
e outras disposições da Directiva
1999/5/CE.
Pioneer izjavlja, da je ta [*] v skladu z
bistvenimi zahtevami in ostalimi
relevantnimi določili direktive
1999/5/ES.
Pioneer tímto prohlašuje, že tento [*] je
ve shodě se základními požadavky a
dalšími příslušnými ustanoveními
směrnice 1999/5/ES
Prin prezenta, Pioneer declara ca acest
[*] este in conformitate cu cerintele
esentiale si alte prevederi ale Directivei
1999/5/EU.
Eesti:
Käesolevaga kinnitab Pioneer seadme
[*] vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele
sätetele.
Magyar:
Alulírott, Pioneer nyilatkozom, hogy a [*]
megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Ar šo Pioneer deklarē, ka [*] atbilst
Direktīvas 1999/5/EK būtiskajām
prasībām un citiem ar to saistītajiem
noteikumiem.
Šiuo Pioneer deklaruoja, kad šis [*]
atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Malti:
Hawnhekk, Pioneer jiddikjara li dan [*]
jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm
fid-Dirrettiva 1999/5/EC
Pioneer týmto vyhlasuje, že [*] spĺňa
základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
С настоящето, Pioneer декларира, че
този [*] отговаря на основните
изисквания и други съответни
постановления на Директива
1999/5/EC.
Polski:
Niniejszym Pioneer oświadcza, że [*]
jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi
postanowieniami Dyrektywy 1999/5/EC
Norsk:
Pioneer erklærer herved at utstyret [*] er
i samsvar med de grunnleggende krav
og øvrige relevante krav i direktiv
1999/5/EF.
Íslenska:
Hér með lýsir Pioneer yfir því að [*] er í
samræmi við grunnkröfur og aðrar
kröfur, sem gerðar eru í tilskipun
1999/5/EC
Hrvatski:
Ovime tvrtka Pioneer izjavljuje da je
ovaj [*] u skladu osnovnim zahtjevima i
ostalim odredbama Direktive
1999/5/EC.
R-TTE-24L_B1_En
http://www.pioneer.fr
http://www.pioneer.de
http://www.pioneer.it
http://www.pioneer.nl
http://www.pioneer.be
http://www.pioneer.es
http://www.pioneer.eu
© 2012 PIONEER CORPORATION.
All rights reserved.
© 2012 PIONEER CORPORATION.
Tous droits de reproduction et de
traduction réservés.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404
PIONEER ELECTRONICS OF CANADA, INC.
340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada TEL: 1-877-283-5901, 905-479-4411
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.
5 Arco Lane, Heatherton, Victoria, 3202, Australia, TEL: (03) 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico, D.F. 11000 TEL: 55-9178-4270
K002_B3_En
Printed in China / Imprimé en Chine
72-BD121W-EU0B3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising