Adventure 4 Plus Adventure 5 Plus
Adventure 4 Plus
Adventure 5 Plus
TREADMILL OWNER’S MANUAL
Read the treadmill guide before using this owner’s manual.
ASSEMBLY
WARNING
There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly
instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the
treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage
to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken.
Before proceeding, find your treadmill’s serial number located on the front stabilizer tube and enter it in the space provided
below. Also locate the model name which is next to the serial number.
ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:
SERIAL NUMBER:
MODEL NAME:
2
Horizon
TREADMILL
3
IPOD/MP3 PLAYER POCKET
SPEAKERS
ALL
MODELS
READING RACK
TOUCH PAD PANEL AND DISPLAY WINDOWS
CONSOLE
FF
FF
FF
FF
6 mm T-Wrench
5 mm L-Wrench
4 mm L-Wrench
4 mm T-Wrench
CONSOLE FAN
WATER BOTTLE HOLDER
SUPPORT BAR
GRIP PULSE HANDRAILS
SAFETY KEY PLACEMENT
ON/OFF SWITCH
CIRCUIT BREAKER
CONSOLE MAST
FOOT LOCK LATCH (UNDERNEATH DECK)
MOTOR COVER
POWER CORD
SIDE RAIL
ROLLER END CAP
RUNNING BELT / RUNNING DECK
PARTS INCLUDED:
FF
FF
FF
FF
FF
FF
FF
FF
1 Console Assembly
2 Console Masts
2 Socket
1 Support Bar
5 Hardware Bags
1 Safety Key
1 Audio Adapter Cable
1 Bottle of Silicone Lubricant
(for 2 applications)
FF 4 iPod® Dock Inserts (Adventure5 only)
FF 1 iPod® Dock Rubber Plug (Adventure5 only)
FF 1 Power Cord
PRE ASSEMBLY
UNPACKING
Place the treadmill carton on a level flat surface. It is recommended that you place a
protective covering on your floor. Take CAUTION when handling and transporting this
unit. Never open box when it is on its side. Once the banding straps have been removed,
do not lift or transport this unit unless it is fully assembled and in the upright folded
position, with the lock latch secure. Unpack the unit where it will be used. The enclosed
treadmill is equipped with high-pressure shocks and may spring open if mishandled.
Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill.
ALL
MODELS
WARNING
DO NOT ATTEMPT TO LIFT THE TREADMILL! Do not move or lift treadmill
from packaging until specified to do so in the assembly instructions. You may
remove the plastic wrap from console masts.
WARNING
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY!
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and
partially threaded in before completely tightening any ONE bolt.
TRANSPORT WHEEL
4
TOOLS INCLUDED:
NOTE: A light application of grease may aid in the installation of hardware. Any grease,
such as lithium bike grease is recommended.
REAR ROLLER
ADJUSTMENT BOLTS
5
ASSEMBLY STEP 1
ASSEMBLY STEP 2
A
HARDWARE BAG 1 CONTENTS :
ALL
MODELS
SOCKET BOLT
10 mm
Qty: 8
B
Cut the yellow banding straps and lift the
running deck upward until the foot
latch locks. Remove all contents from
underneath the running deck.
HARDWARE BAG 2 CONTENTS :
BOLT (A)
20 mm
Qty: 4
Open hardware bag 1.
C Attach the LEFT SOCKET to the LEFT
console mast using 4 SOCKET bolts
(a).
D
SPRING WASHER (B)
15 mm
Qty: 4
Attach the RIGHT SOCKET to the RIGHT
console mast using 4 SOCKET bolts
(a).
FLAT WASHER (C)
15 mm
Qty: 4
A
Open hardware bag 2.
B
With the running deck in the raised
position, attach the left console mast
to the base frame using 4 bolts (a),
4 spring washers (b) and 4 flat
washers (c).
ALL
MODELS
RUNNING DECK
LEFT
CONSOLE
MAST
CONSOLE MAST
FOOT LATCH
SOCKET BOLT
BASE FRAME
SOCKET
FLAT WASHERS (C)
SPRING WASHERS (B)
BOLTS (A)
6
7
ASSEMBLY STEP 3
ASSEMBLY STEP 4
HARDWARE BAG 3 CONTENTS :
ALL
MODELS
BOLT (A)
20 mm
Qty: 4
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (C)
15 mm
Qty: 4
A
Open hardware bag 3.
B
Pull lead wire through right console
mast. After pulling the lead wire through the
mast, the top of the console cable should
be located at the top of the mast. Detach and
discard the lead wire.
HARDWARE BAG 4 CONTENTS :
BOLT (D)
15 mm
Qty: 4
SPRING WASHER (B)
15 mm
Qty: 4
FLAT WASHER (C)
15 mm
Qty: 4
A
Disengage the deck lock latch with your
foot to lower the running deck.
B
Open hardware bag 4.
C Gently place the console on top of the
console masts. Attach the left side first
using 2 bolts (d), 2 spring washers (b)
and 2 flat washers (c).
CONSOLE
C With the running deck in the raised
LEAD WIRE
RUNNING DECK
position, attach the right console
mast to the base frame using 4 bolts
(a), 4 spring washers (b) and 4 flat
washers (c).
CONSOLE CABLES
CONSOLE CABLE
RIGHT CONSOLE MAST
BOLTS (A)
SPRING WASHERS (B)
FLAT WASHERS (C)
Note: Be careful not to pinch any wires
while assembling the right console mast.
ALL
MODELS
ASSEMBLE
LEFT SIDE
FIRST
BOLTS (D)
D
Connect the console cables, carefully
tucking wires in masts to avoid damage.
E
Attach the right side of the console
using 2 bolts (d), 2 spring washers
(b) and 2 flat washers (c).
Note: Be careful not to pinch any wires
while assembling the masts.
SPRING WASHERS (B)
FLAT WASHERS (C)
CONSOLE MAST
BASE FRAME
8
9
ASSEMBLY STEP 5
HARDWARE BAG 5 CONTENTS :
ALL
MODELS
BOLT (A)
15 mm
Qty: 4
ASSEMBLY STEP 6
A
Open hardware bag 5.
B
Align SUPPORT BAR with holes in CONSOLE
MASTS.
ALL
MODELS
C Insert BOLTS (A) into all 4 holes of the
SUPPORT BAR.
D
Tighten all console bolts (Step 3) and support
bar bolts (Step C above) completely.
SUPPORT BAR
BOLT (A)
CONSOLE MAST
YOU ARE FINISHED!
10
11
TREADMILL OPERATION
This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the
treadmill guide has instructions for the following:
• LOCATION OF THE TREADMILL
• Using the SAFETY KEY
• FOLDING the treadmill
• MOVING the treadmill
• LEVELING the treadmill
• ­TENSIONING THE RUNNING BELT
• CENTERING THE RUNNING BELT
• Using the HEART RATE function
13
U
C
D
A
O
B
E
M
w
Q
N
Adventure 4 PLUS CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) Display windows: time, distance, calories, heart rate, speed, incline and workout profiles.
P
P
S
B) Alphanumeric display: displays goal and program information.
C) Select target: press to select your desired target.
Adventure
4 Plus
D) Select workout: press to select your desired workout.
ZEIT
E) Goal center™: press to set or view your goal.
ENTFERNUNG
HEART RATE
F) Start: press to begin exercising, start your workout, or resume exercising after pause.
ENERGY SAVER
HERZFREQUENZ
ENERGIESPARMODUS
K ALORIEN
STEIGUNG
G) Stop: press to pause/end your workout. Hold for 3 seconds to reset the console.
GESCHWINDIGKEIT
H) Incline
I)
km/h
MPH
km/h
MPH
km/h
MPH
km/h
MPH
km/h
MPH
MPH
WARNUNG!
Besuchen Sie einen Arzt, bevor Sie das Gerät benutzen. Falls Sie während des Trainings
Übelkeit, Brustschmerzen, Schwindelanfälle oder Atemnot verspüren, beenden Sie Ihr
Training sofort und suchen Sie einen Arzt auf.
Nur für den Heimgebrauch.
Befestigen Sie den Sicherheitsclip an Ihrer Kleidung, bevor Sie das Gerät starten. Um das Risiko von Verletzungen einzudämmen, stellen Sie sich auf die
seitlichen Trittflächen, bevor Sie das Laufband starten. Lesen Sie vor der Erstbenutzung die Bedienungsanleitung. Halten Sie Kinder von dem Gerät
fern. Entfernen Sie den Sicherheitsschlüssel nach dem Training, um ein ungewolltes Einschalten durch Kinder vorzubeugen.
SELECT TARGET
SELECT WORKOUT
ZIEL AUSWÄHLEN
PROGRAMM AUSWÄHLEN
ENTER
EINGABE
km/h
MPH
T
km/h
FAN
MPH
VENTILATOR
AKTUELLES TRAINING
GOAL
keys: used to adjust incline in small increments (0.5% increments).
K) Speed quick keys: used to reach desired speed more quickly.
MPH
ACHTUNG!
/
Speed + / - keys: used to adjust speed in small increments (0.1 Mph or 0.1 KMph increments).
J) Incline quick keys: used to reach desired incline more quickly.
km/h
km/h
T
Adventure
4 Plus
L) Change display: press to change display feedback during workout.
M) Enter: used to confirm target and workout settings.
km/h
CENTER
MPH
N) Fan key: press to turn fan on and off.
FÜR ZIELAUSWAHL ODER ZIELANSICHT DRÜCKEN
km/h
MPH
ADVENTURE 4 PLUS
O) Fan: personal workout fan.
km/h
MPH
P) Speakers: music plays through speakers when your cd / mp3 player is connected to the console.
Q) Audio in jack: plug your cd / mp3 player into the console using the included audio adaptor cable.
R) Audio out / headphone jack: plug your headphones into this jack to listen to your music through the headphones.
Note: when headphones are plugged into the headphone jack the sound will no longer come out through the speakers.
ANZEIGENWECHSEL
GESCHWINDIGKEIT
STEIGUNG
HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCK T HALTEN
V
S) MP3 player pocket: used to store your mp3 player.
T) Water bottle pockets: holds personal workout equipment.
J
14
H
F
L
R
G
I
K
U) Reading rack: holds reading material.
V) Safety key position: enables treadmill when safety key is inserted.
W) Energy saver: after entering stand-by mode for 10 mins energy saver will run automatically to minimize energy consumption.
* Maximum user’s body weight = 147 kg / 325 lbs.
15
U
C
D
A
O
P
B
E
Y
M
Q
W
P
S
Adventure
5 Plus
STEIGUNG
K ALORIEN
HERZFREQUENZ
GESCHWINDIGKEIT
ENERGY SAVER
ENERGIESPARMODUS
ZEIT
ENTFERNUNG
km/h
MPH
km/h
MPH
km/h
MPH
km/h
km/h
MPH
MPH
km/h
MPH
km/h
MPH
ACHTUNG!
WARNUNG!
Besuchen Sie einen Arzt, bevor Sie das Gerät benutzen. Falls Sie während des Trainings
Übelkeit, Brustschmerzen, Schwindelanfälle oder Atemnot verspüren, beenden Sie Ihr
Training sofort und suchen Sie einen Arzt auf.
Nur für den Heimgebrauch.
Befestigen Sie den Sicherheitsclip an Ihrer Kleidung, bevor Sie das Gerät starten. Um das Risiko von Verletzungen einzudämmen, stellen Sie sich auf die
seitlichen Trittflächen, bevor Sie das Laufband starten. Lesen Sie vor der Erstbenutzung die Bedienungsanleitung. Halten Sie Kinder von dem Gerät
fern. Entfernen Sie den Sicherheitsschlüssel nach dem Training, um ein ungewolltes Einschalten durch Kinder vorzubeugen.
T
SELECT TARGET
SELECT WORKOUT
ZIEL AUSWÄHLEN
PROGRAMM AUSWÄHLEN
ENTER
EINGABE
km/h
MPH
T
km/h
CUSTOM
1 or 2
MPH
BENUTZER 1 oder 2
AKTUELLES TRAINING
km/h
GOAL
MPH
CENTER
FÜR ZIELAUSWAHL ODER ZIELANSICHT DRÜCKEN
km/h
MPH
ADVENTURE 5 PLUS
km/h
CHANGE
DISPLAYS
FAN
VENTILATOR
MPH
ANZEIGENWECHSEL
Controls
iPod ®
ZURÜCK
AUSWÄHLEN
STEIGUNG
GESCHWINDIGKEIT
HOLD TO RESET
FÜR NULLSTELLUNG
GEDRÜCK T HALTEN
V
J
16
N
H
F
X
R
G
I
L
K
Adventure 5 PLUS CONSOLE OPERATION
Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.
A) Display windows: time, distance, calories, heart rate, speed, incline and workout profiles.
B) Alphanumeric display: displays goal and program information.
C) Select target: press to select your desired target.
D) Select workout: press to select your desired workout.
E) Goal center™: press to set or view your goal.
F) Start: press to begin exercising, start your workout, or resume exercising after pause.
G) Stop: press to pause/end your workout. Hold for 3 seconds to reset the console.
H) Incline / keys: used to adjust incline in small increments (0.5% increments).
I) Speed + / - keys: used to adjust speed in small increments (0.1 Mph or 0.1 KMph increments).
J) Incline quick keys: used to reach desired incline more quickly.
K) Speed quick keys: used to reach desired speed more quickly.
L) Change display: press to change display feedback during workout.
M) Enter: used to confirm target and workout settings.
N) Fan key: press to turn fan on and off.
O) Fan: personal workout fan.
P) Speakers: music plays through speakers when your cd / mp3 player is connected to the console.
Q) Audio in jack: plug your cd / mp3 player into the console using the included audio adaptor cable.
R) Audio out / headphone jack: plug your headphones into this jack to listen to your music through the headphones.
Note: when headphones are plugged into the headphone jack the sound will no longer come out through the speakers.
S) iPod® docking station: used to dock and charge your iPod (not included).
T) Water bottle pockets: holds personal workout equipment.
U) Reading rack: holds reading material.
V) Safety key position: enables treadmill when safety key is inserted.
W) Custom 1 OR 2 key: press to select Custom 1 or Custom 2 program.
X) iPod® controls: press to adjust your attached iPod audio settings.
Y) Energy saver: after entering stand-by mode for 10 mins energy saver will run automatically to minimize energy consumption.
* Maximum user’s body weight = 160 kg / 350 lbs.
Adventure
5 Plus
17
Display windows
• TIME: Shown as minutes : seconds. View the time
remaining or the time elapsed in your workout.
ZEIT
• DISTANCE: Shown as miles or kms. Indicates
distance traveled or distance remaining during your
workout.
1) Check to make sure no objects are placed on the
belt that will hinder the movement of the treadmill.
ENTFERNUNG
HEART RATE
K ALORIEN
STEIGUNG
ENERGIESPARMODUS
• Targets:
Target will be displayed in the alphanumeric window
on the bottom of the display.
• Workouts:
Workout will be displayed in the alphanumeric window
on the bottom of the display.
18
CHANGING YOUR TARGET MID-WORKOUT
3) Stand on the side rails of the treadmill.
You can change your Target “on-the-fly” without losing your
current workout stats.
5) Insert the safety key into the safety keyhole in the
console.
Adventure 5 Plus DISPLAYS
6) You have two options to start your workout:
STEIGUNG
K ALORIEN
HERZFREQUENZ
GESCHWINDIGKEIT
A) Quick start up
ENERGY SAVER
ENERGIESPARMODUS
• PROGRAM PROFILES: Represents the profile of
the program being used (speed during speed based
programs and incline during incline based programs).
2) Plug in the power cord and turn the treadmill ON.
4) Attach the safety key clip to part of your clothing
making sure that it is secure and will not become
detached during operation.
GESCHWINDIGKEIT
• CALORIES: Total calories burned or calories
remaining left to burn during your workout.
• HEART RATE: Shown as BPM (beats per minute).
Used to monitor your heart rate (displayed when
contact is made with both pulse grips).
NOTE: If no target or workout is selected, the program
will function as a manual program. All changes in speed
and incline will need to be from the user in this setting.
ENERGY SAVER
HERZFREQUENZ
• SPEED: Shown as MPH or KMPH. Indicates how
fast your walking or running surface is moving.
• INCLINE: Shown as percent. Indicates the incline of
your walking or running surface.
GETTING STARTED
Adventure 4 Plus DISPLAYS
ZEIT
ENTFERNUNG
Simply press the go/START key to begin working out.
Time, distance, and calories will all count up from zero.
OR...
B) Select a target and workout
1) Select a target using the select target key.
2) Adjust the target settings using the arrow keys.
3) Press enter to advance.
4) Select a workout using the select
workout key.
5) Press go/start to begin workout.
Anytime during your workout, press the SELECT TARGET key
until you have selected the new TARGET you would like.
Use the / or + / – keys to enter in the value of your new
TARGET and press enter. All previous workout statistics will
be rolled into the new TARGET, so you’ll never miss a beat.
NOTE: If you accidentally press the SELECT TARGET key
during a workout, do not press any button till the setting
mode disappears, the current target will resume.
CHANGING YOUR workout MID-WORKOUT
You can change your Workout “on-the-fly”.
Anytime during your workout, press the SELECT WORKOUT
key until you have selected the new WORKOUT you would like.
Press ENTER.
New workout will begin at the first segment after warm up
and all workout statistics will roll over.
NOTE: HRC is not available for workout changing. If you
accidentally press the SELECT WORKOUT button during
a workout, do not press any button till the setting mode
disappears, the current target will resume.
19
TARGET PROFILES
TARGET 1 – TIME: Allows user to set a target based on how long they would like to workout. Time targets can range
from 15:00 – 99:00. TIME will count down. DISTANCE and CALORIES will count up from zero.
TARGET 2 – DISTANCE: Allows user to set a target based on distance they would like to complete. Distance target
can range from 0.25 – 26.25 MILE or 0.4-42 KM. DISTANCE will count down. TIME and CALORIES will count up
from zero.
Target 3 – calories: Allows user to set a target based on the number of calories they would like to burn. Calories
target can range from 20 – 980 calories. CALORIES will count down. TIME and DISTANCE will count up from zero.
NO TARGET: Allows user to select a workout profile that has no specified time, distance, or calorie target.
TIME, DISTANCE, and CALORIES will all count up from zero.
WORKOUT PROFILES
1) manual: Allows ‘on the fly’ manual speed and incline changes.
2) intervals: Improves your strength, speed and endurance by increasing and decreasing the speed throughout your workout to
involve your heart and other muscles.
Segment
Warm Up
1
2
Time
2:00 Mins
2:00 Mins
90 sec
30 sec
Speed
1
1.5
2
4
Incline
1
1.5
0.5
1.5
Segments 1 & 2
repeat until target is
complete
3) HILLS: Simulates running up and down hills to improve stamina.
Segment
Warm Up
1
2
3
4
5
6
7
8
Time
4:00 Mins
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
2
2.5
3
3.5
4
3.5
3
2.5
Level 1
Incline
1
1.5
Segments 1–8
repeat until target
is complete
4) weight loss: Promotes weight loss by increasing and decreasing the speed, while keeping you in your fat burning zone.
Segment
Warm Up
1
2
3
4
5
6
7
8
Time
4:00 Mins
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
30 sec
Level 1
Incline
0
0.5
1.5
1.5
1
0.5
0.5
0.5
1
1.5
Speed
1
1.5
2
2.5
3
3.5
4
3.5
3
2.5
Segments 1–8
repeat until target
is complete
5) HRC: Once the HRC program is selected, press ‘enter’. To adjust your target heart rate, press the plus (+) or minus (-) incline
buttons.
Your target heart rate should be set at a number that you will be able to exercise at throughout the majority of your workout.
Once you have chosen your target heart rate, press the ‘Start’ button and begin your workout.
After the 4 minute warm up period, the elevation level will increase gradually to get the user to the entered target heart rate
zone. Once the user is at the target heartrate zone, plus or minus 5 beats, the elevation level will remain at the currentresistance
level.
If the user is more than 25 beats per minute above the target heart rate zone, the console will shut down for safety reasons.
NOTE:The chest strap is required to use the HRC program, with HRC program you can only choose time as your workout target.
20
21
Using custom workouts (Adventure 5 Plus only)
1) Select User by using the
/
or + / – keys and press enter
2) Press the CUSTOM 1 OR 2 key to select a custom workout.
3) Press select target key to select a time, distance, or calories target. Press enter to select desired target.
4) Set each speed profile by using the
/
or + / – keys and press enter. Repeat for all 15 speed profiles.
5) Set each incline profile by using the
/
or + / – keys and press enter. Repeat for all 15 incline profiles.In
6) Press start to begin.
Goal center™
Research shows that those who create and track their fitness goals, on average, achieve greater success than those who do not.
Because your new treadmill is equipped with Horizon’s exclusive goal center™ Performance Tracker, you’ve taken an important
step towards achieving your fitness goals. Goal center™ is innovative new software, integrated into your treadmill console, that
will allow you to track your fitness goals over time, without the need for paper journals or logs. Read further to learn about how goal
center™ can help motivate you to enhance your performance.
Goal center™ setup
1) Select user 1 or user 2 using the
/
or + / – keys and press enter.
2) Press and hold goal center™ for approximately five seconds.
3) Press select target key to select time, distance or calorie goal.
4) Use
5) Use the
/
or + / – keys to select goal value and press enter.
/
or + / – keys to select the number of days to complete the goal.
6) Press enter again to exit the setup mode.
NOTE: These steps can also be used to erase an existing goal and set a new one.
Viewing goal progress
When logged into your user profile, you can view progress toward your goal by pressing the goal center™ key. The console will scroll
the remaining time, distance or calories, depending on the goal selected and will also scroll the time remaining to achieve that goal.
NOTE: For workout data to accumulate towards a user’s goal, you must first select that user before beginning a workout.
22
23
IPOD® DOCKING STATION
To reset the console
Hold stop key for 3 seconds.
Finishing your workout
When your workout is complete, the monitor display will flash “FINISHED” and beep. Your workout information will stay displayed on
the console for 30-45 seconds and then reset.
Clear current selection
To clear the current program selection or screen, hold the stop button for 3-5 seconds.
Using your CD / MP3 player
1) Connect the included audio adaptor cable to the audio in jack on the top right of the console and the headphone
jack on your cd / mp3 player.
2) Use your cd / mp3 player buttons to adjust song settings.
3) Remove the audio adaptor cable when not in use.
4) If you don’t want to use the speakers, you can plug your headphones into the audio out jack at the bottom of the
console.
iPod docking station
(Adventure 5 Plus only)
®
RUBBER PLUG
The iPod docking station is the entertainment solution for your workouts.
Various iPod models with a dock connector can fit this dock. IPhone is not
compatible.
Using the iPod docking station
(ipod not included)
1) Remove the rubber plug from bottom of the docking station.
2) Plug in your iPod by matching the dock connector pin on the
treadmill with the dock connector on your iPod. NOTE: Once you
have connected the iPod to the docking station, please allow 2
minutes for the iPod and docking station to sync up before it will be
fully functional.
3) You can use your iPod dial to adjust volume and song settings.
Or you can adjust your volume and song settings using the iPod
control keys on the treadmill console. NOTE: If you don’t want to
use the speakers, you can plug your headphones into the audio out
jack at the bottom of the console.
Replace the rubber plug into the bottom of the docking station when the
station is not in use.
DOCK
INSERT
DOCK CONNECTOR PIN
AUDIO IN JACK FOR NON-IPOD PLAYERS
IPOD® DOCKING STATION
RUBBER PLUG
DOCK CONNECTOR PIN
AUDIO IN JACK FOR NON-IPOD PLAYERS
IPOD® CONTROLS
Controls
iPod ®
Back
NOTE: iPod audio will not play through speakers if audio adaptor cable is
plugged in while iPod is in the docking station.
Select
AUDIO OUT JACK
iPod® Dock Inserts
Note: Dock insert sizes
vary for each iPod.
24
Universal MP3 Player
Dock Insert
IPOD® CONTROLS
Controls
iPod ®
Back
25
TREADMILL OWNER’S MANUAL
Adventure 4 Plus & Adventure 5 Plus Treadmill Owner’s Manual 052011 Rev1.0 © 2011 Horizon Fitness
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising