29101.1X PKZ Ultra Micro Polecat BNF manual

29101.1X PKZ Ultra Micro Polecat BNF manual
Ultra Micro Pole Cat
Instruction Manual
Bedienungsanleitung
Manuel d’utilisation
Manuale di Istruzioni
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole
discretion of Horizon Hobby, Inc. For up-to-date product literature, visit
www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of
potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical
property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical
property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property
damage, collateral damage and serious injury OR create a high probability of
superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features
of the product before operating. Failure to operate the product correctly can result in
damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense
and requires some basic mechanical ability. Failure to operate this Product in a safe and
responsible manner could result in injury or damage to the product or other property. This
product is not intended for use by children without direct adult supervision. Do not attempt
disassembly, use with incompatible components or augment product in any way without
the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the
manual prior to assembly, setup or use in order to operate correctly and avoid damage or
serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
2
EN
Thank you for purchasing the ParkZone® Ultra Micro Series Pole Cat. You’re just a battery charge
away from one of the most exciting Ultra Micro flying experiences available. This Pole Cat has
been specially designed to look like a full-scale Formula-1 air racer yet remain as forgiving as any
sport plane. Whether you’re banking and yanking at high speed around the pylons, or simply
shooting touch and go landings, the Pole Cat is a joy to fly at any speed.
Before you take that first flight though, please take some time to read through this manual. In
addition to instructions for binding it to your DSM2® or DSMX® transmitter, you’ll find control
setup and charging tips, as well as a handy troubleshooting guide. It’s all here so you can get the
most from your Pole Cat– first flight and every flight.
Table of Contents
Specifications .............................................................3
Charging the Battery ...............................................4
Charging Warnings ..................................................5
Low Voltage Cutoff (LVC) .......................................5
Transmitter and Receiver Binding ......................6
Installing the Flight Battery
and Arming the ESC ...............................................6
Preflight Checklist ....................................................7
Control Centering ....................................................7
Settings for Control Horns ....................................7
Control Rates..............................................................8
Model Decals .............................................................8
Adjusting Center of Gravity (CG).........................8
Control Direction Test .............................................9
Propeller and Propeller Shaft Maintenance....10
Flying Tips and Repairs ........................................ 11
Post Flight Checklist ............................................. 11
Additional Safety Precautions
and Warnings .......................................................... 12
Removing and Installing Landing Gear......... 12
Troubleshooting Guide ....................................... 13
Warranty and Repair Policy ................................ 14
Warranty and Service Information .................. 15
Compliance Information for
the European Union ............................................. 15
Parts Contact Information .................................. 58
Replacement Parts ................................................ 58
Optional Parts and Accessories ........................ 59
Specifications
15.4 in (391 mm)
16.1 in (409 mm)
Installed
SpektrumTM AR6410L Receiver/
Servos/Esc
Included
Battery: 150mAh 3.7 25C Li-Po
Included
Charger: 1S 3.7V Li-Po Battery
Charger
Needed to
Complete
DSM2/DSMX 4-Channel Transmitter
1.25 oz (35.3 g)
To register your product online, go to www.parkzone.com
EN
3
Charging the Battery
Your Pole Cat comes with a 1S 3.7V Li-Po
Battery Charger and a 1S Li-Po battery. You
should only charge your 1S Li-Po battery with
the included charger, or the E-flite® Celectra™
4-port Charger (EFLC1004). The flight battery
will be required to confirm proper aircraft
operation in future steps.
The Battery Charging Process
1. Charge only batteries that are cool to the touch and are not damaged. Look at the battery to
make sure it is not damaged e.g., swollen, bent, broken or punctured.
2. Remove the cover on the bottom of the charger and install four of the included AA batteries,
noting proper polarity. Replace the cover after the AA batteries are installed.
3. Slide the battery into the slot on the charger. The end cap of the battery is specifically designed
to allow the battery to fit into the slot one way (usually with the label on the battery facing
outward) to prevent reverse polarity connection. However, check for proper alignment and
polarity before proceeding to the next step.
4. Gently press the battery and its connector into the charge jack/connector located at the bottom
of the slot in the charger.
5. When you make the connection successfully, the LED on the charger turns solid red, indicating
charging has begun.
6. Charging a fully discharged (not over-discharged) 150mAh battery takes approximately 30–40
minutes. As the battery nears full charge, the LED begins to blink.
7. When the battery is fully charged, the LED blinks approximately every 20 seconds or goes out
entirely. Note: If the LED stays on when the battery is removed, the AA batteries in the charger
are low.
8. Always unplug the battery from the charger immediately upon completion of charging.
CAUTION: Overcharging a battery can cause a fire.
CAUTION: Only use a charger specifically designed to charge a Li-Po battery. Failure
to do so could result in a fire, causing injury or property damage.
CAUTION: Only use an E-flite 6V power supply (EFLC1005) with this charger. DO NOT
use a 12V power supply or property damage and injury could occur.
4
EN
Charging Warnings
The Battery Charger (EFLC1000) included
with your aircraft has been designed to safely
charge the Li-Po battery.
CAUTION: All instructions and warnings
must be followed exactly. Mishandling of
Li-Po batteries can result in a fire, personal
injury and/or property damage.
• By handling, charging or using the included
Li-Po battery, you assume all risks associated
with lithium batteries.
• If at any time the battery begins to balloon
or swell, discontinue use immediately. If
charging or discharging, discontinue and
disconnect. Continuing to use, charge or
discharge a battery that is ballooning or
swelling can result in fire.
• Always store the battery at room
temperature in a dry area for best results.
• Always transport or temporarily store the
battery in a temperature range of 40–120º F
(5–49° C). Do not store battery or model in
a car or direct sunlight. If stored in a hot car,
the battery can be damaged or even catch
fire.
• Always charge batteries away from
flammable materials.
• Always inspect the battery before charging
and never charge dead or damaged
batteries.
• Always disconnect the battery after
charging, and let the charger cool between
charges.
• Always constantly monitor the temperature
of the battery pack while charging.
• ONLY USE A CHARGER SPECIFICALLY
DESIGNED TO CHARGE LI-PO BATTERIES.
Failure to charge the battery with a
compatible charger may cause a fire
resulting in personal injury and/or property
damage.
• Never discharge Li-Po cells to below 3V
under load.
• Never cover warning labels with hook and
loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside
recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the
charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot
or cold places (recommended between
40–120° F or (5–49° C) or place in direct
sunlight.
Low Voltage Cutoff (LVC)
When a Li-Po battery is discharged below
3V, it will not hold a charge. The Pole Cat ESC
protects the flight battery from over-discharge
using Low Voltage Cutoff (LVC). Before the
battery charge decreases too much, LVC
removes power supply from the motor. Power
to the motor quickly decreases and increases,
showing some battery power is reserved for
flight control and safe landing.
When the motor power pulses, land the
aircraft immediately and recharge the
flight battery.
Disconnect and remove the Li-Po battery from
the aircraft after use to prevent trickle
discharge. Fully charge your Li-Po battery
before storing it. During storage, make sure
battery charge does not fall below 3V per cell.
For your first flights, set your transmitter timer
or a stopwatch to 4 minutes. Adjust your
timer for longer or shorter flights once you
have flown the model. Flights of 6 minutes or
more are achievable if using proper throttle
management.
NOTICE: Repeated flying to LVC will damage
the battery.
EN
5
Transmitter and Receiver Binding
Binding is the process of programming the receiver of the control unit to recognize the GUID
(Globally Unique Identifier) code of a single specific transmitter. You need to “bind”your chosen
SpektrumTM DSM® technology equipped aircraft transmitter to the receiver for proper operation.
For a list of compatible DSM2/DSMX transmitters, please visit www.bindnfly.com.
CAUTION: When using a Futaba transmitter with a Spektrum DSM module, you must
reverse the throttle channel and rebind. Refer to your Spektrum module manual for
binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions
on reversing the throttle channel.
9 Binding Procedure Reference Table
1. Refer to your transmitter’s unique instructions for binding to a receiver.
2. Make sure the flight battery is disconnected from the airplane.
3. Power off the transmitter.
4. Connect the flight battery to the aircraft. The receiver LED will begin to flash (typically after 5
seconds).
5. Make sure transmitter controls are neutral and that throttle and throttle trim are in low position.
6. Put your transmitter into bind mode. Refer to your transmitter’s manual for binding button or
switch instructions.
7. After 5 to 10 seconds, the receiver status LED will become solid, indicating that the receiver is
bound to the transmitter.
Note: If the LED does not go to a solid light, refer to Troubleshooting Guide at back of manual.
Installing the Flight Battery
and Arming the ESC
Arming the ESC also occurs after binding
as previously described, but subsequent
connection of a flight battery requires the
following steps.
CAUTION: Always keep hands away
from propeller. When armed, the
motor will turn the propeller in response to
any throttle movement.
Lower throttle 1
and throttle
trim to lowest
settings.
Power on
the transmitter, then
wait 5 seconds
Connect the
flight battery
and attach to
the hook and
loop strip.
2
Series of
tones
3
Continuous
LED
6
EN
Preflight Checklist
9
9
1. Charge flight battery.
6. Adjust center of gravity.
2. Install flight battery in aircraft
(once it has been fully charged).
7. Perform a radio system Range
Check.
3. Bind aircraft to transmitter.
8. Find a safe and open area.
4. Make sure linkages move freely.
9. Plan flight for flying field conditions.
5. Perform Control Direction Test with
transmitter.
Control Centering
Before first flights, or in the event of an
accident, make sure the flight control surfaces
are centered. Adjust linkages mechanically if
control surfaces are not centered.
Use of the transmitter trims may not correctly
center the aircraft control surfaces due to the
mechanical limits of linear servos.
1. Make sure control surfaces are neutral
when the transmitter controls and trims
are centered. Where possible, transmitter
sub-trim must be set to zero.
2. When needed, use a pair of pliers to
carefully bend the metal of the linkage
(see illustration).
3. Make the U-shape narrower to make the
connector shorter. Make the U-shape
wider to make the linkage longer.
NOTICE: When using a programmable
transmitter, do not use Sub-Trim to adjust the
center position of the servo.
NOTICE: Never set Travel Adjust above
100%. Ultra Micro servos are unique in that
they are calibrated to reach maximum travel
at 100% travel adjust. Increasing the value
above 100% will NOT result in more travel, but
can cause the servo to lock and will result in
a crash.
Settings for Control Horns
Elevator
Rudder
The illustration shows factory settings for
linkages on control horns. After flying, if you
want more control throw, carefully adjust
linkage positions for desired control response.
EN
7
Control Rates
We recommend using a DSM2/DSMX aircraft
transmitter. Adjust according to individual
preferences after initial flight.
It is normal for linear servos to make noise.
The noise is not an indication of a faulty servo.
To achieve the proper Low Rate settings when
using a programmable DSM2/DSMX aircraft
transmitter, set the Low Rate value to 70% for
aileron, elevator and rudder.
High Rate
Low Rate
Aileron
6mm up/down
4mm up/down
Elevator
5mm up/down
4mm up/down
Rudder
9mm left/right
6mm left/right
Note: All control surfaces are measured at the
widest point.
Model Decals
An additional decal sheet has been included
in the box to personalize your model with
your favorite racing number.
Apply these decals in any location you may
choose.
NOTICE: Be sure to balance your model and
find the correct center of gravity after applying the decals. Decal application can affect
center of gravity.
Adjusting Center of Gravity (CG)
The CG location is 22–25mm back from the
leading edge of the wing at the fuselage.
This CG location has been determined with
the included 1S 150mAh 3.7V Li-Po battery
installed in the front of the battery cavity.
The battery cavity is oversized to allow for
Center of Gravity adjustment. Start by placing
the battery in the front of the cavity and
adjust as needed.
22–25mm
8
EN
Control Direction Test
Bind your aircraft and transmitter before doing these tests (see Binding). Move the controls on
the transmitter to make sure aircraft control surfaces move correctly (Mode 2 shown).
Up
Elevator
Down
Elevator
Left
Aileron
Right
Aileron
Left
Rudder
Right
Rudder
EN
9
Propeller and Propeller Shaft Maintenance
CAUTION: DO NOT handle propeller
parts while the flight battery is
connected. Personal injury could result.
Diassembly
1. Carefully cut tape and decals on fuselage
and turtle deck (top of fuselage behind
canopy) and remove top of fuselage.
Note: Removing tape or decals will remove
paint from the fuselage.
2. Hold the prop shaft using needle-nose
pliers or hemostats.
3. Turn propeller counterclockwise
(looking from front of model) to remove.
Turn propeller clockwise to install.
4. Carefully remove a damaged spinner
and glue from propeller.
5. Hold nut on end of prop shaft using
needle-nose pliers or hemostats.
6. Turn gear on shaft clockwise (looking
from front of model) to remove nut.
Remove
Install
7. Cut a small amount of foam from fuselage
before removing prop shaft.
8. Gently pull shaft (A) from gearbox (B)
and make sure washer (C) and
two bushings (D) are not lost.
9. Disconnect motor from ESC/receiver.
10. Gently push motor out of gearbox and
remove motor through top of fuselage
behind the ESC/receiver.
A
D
C
NOTICE: DO NOT remove gearbox from
model. Damage to model will result.
B
Assembly
Assemble model using instructions above,
in reverse order.
• Correctly align prop shaft gear with
pinion gear on motor.
• Correctly connect motor to ESC/receiver
so that powered motor turns propeller
clockwise (looking from front of model).
• Attach spinner to propeller using CA or
foam-compatible CA.
• Assemble fuselage using clear tape.
10
EN
Flying Tips and Repairs
Flying
We recommend only flying your Pole Cat in
light winds. Always avoid flying near houses,
trees, wires and buildings. You should also be
careful to avoid flying in areas where there are
many people, such as busy parks, schoolyards
or soccer fields. Consult local laws and ordinances before choosing a location to fly
your aircraft.
Failure to lower the throttle
stick and trim to the lowest
possible position during a
crash could result in damage
to the ESC in the receiver
unit, which may require
replacement.
NOTICE: Crash damage is not
covered under warranty.
CAUTION:
Always
decrease throttle at
propeller strike.
Place the Pole Cat in position for takeoff
(facing into the wind if flying outdoors).
Gradually increase the throttle to ¾ to full, and
steer with the rudder. Pull back gently with
the elevator and climb to check trim. Once
the trim is adjusted, begin exploring the flight
envelope of the Pole Cat.
Repairs
Due to the large propeller on the Pole Cat, it is
possible to hit the prop on the ground while
landing. Make sure to flare when landing and
try to land as smoothly as possible to minimize
hitting the prop. While this does not damage
the airplane, it is possible to wear down the
tips of the propeller if flying from an abrasive
surface such as concrete or asphalt.
For a listing of all replacement and optional
parts, refer to the list at the back of this
manual.
Repair the Pole Cat using foam-compatible
CA (cyanoacrylate) glue or clear tape. Only
use foam-compatible CA glue, as other types
of glue can damage the foam. When parts are
not repairable, see the Replacement Parts List
for ordering by item number.
NOTICE: Use of foam-compatible CA accelerant on your model can damage paint. DO NOT
handle model until accelerant fully dries.
Post Flight Checklist
9
9
1. Disconnect flight battery from ESC
(Required for Safety and battery life).
5. Store flight battery apart from
aircraft and monitor the battery
charge.
2. Power off transmitter.
6. Make note of flight conditions and
flight plan results, planning for
future flights.
3. Remove flight battery from aircraft.
4. Recharge flight battery
EN
11
Additional Safety Precautions and Warnings
• Never place any portion of the model in your
mouth as it could cause serious injury or even
death.
• Never operate your model with low transmitter
batteries.
Always keep a safe distance in all directions
• Always keep aircraft in sight and under control.
around your model to avoid collisions or injury.
• Always use fully charged batteries.
This model is controlled by a radio signal subject • Always keep transmitter powered on while
to interference from many sources outside your
aircraft is powered.
control. Interference can cause momentary loss
•
Always
remove batteries before disassembly.
of control.
•
Always
keep
moving parts clean.
Always operate your model in open spaces away
• Always keep parts dry.
from full-size vehicles, traffi c and people.
• Always let parts cool after use before touching.
Always carefully follow the directions and
• Always remove batteries after use.
warnings for this and any optional support
equipment (chargers, rechargeable battery
• Always ensure failsafe is properly set before
packs, etc.).
flying.
Always keep all chemicals, small parts and
• Never operate aircraft with damaged wiring.
anything electrical out of the reach of children.
• Never touch moving parts.
Always avoid water exposure to all equipment
not specifi cally designed and protected for
this purpose. Moisture causes damage to
electronics.
As the user of this product, you are solely
responsible for operating in a manner that
does not endanger yourself and others
or result in damage to the product or the
property of others.
•
•
•
•
•
Removing and Installing Landing Gear
To Remove:
1. Press together the sides of the landing gear
to make the center loop thinner.
2. Pull the landing gear from the fuselage of
the model.
To Install:
1. Press together the sides of the landing
gear to make the center loop thinner.
2. Push the center loop in the slot in the
bottom of the fuselage.
3. Release the landing gear, then pull gently
on the landing gear to make sure it is
fully installed.
12
EN
Troubleshooting Guide
Problem
Aircraft will not respond
to throttle but responds to
other controls
Possible Cause
Throttle stick and/or throttle trim too high
Throttle channel is reversed
Solution
Reset controls with throttle stick and throttle trim at
lowest setting
Reverse throttle channel on transmitter
Motor unplugged from receiver
Extra propeller noise or
extra vibration
Reduced flight time or
aircraft underpowered
Open fuselage and ensure the plug for the motor is
properly installed
Damaged propeller, spinner, prop shaft or motor Replace damaged parts
Nut on prop shaft is too loose
Tighten the prop shaft nut 1/2 turn
Flight battery charge is low
Completely recharge flight battery
Propeller installed backwards
Install propeller with numbers facing forward
Flight battery damaged
Replace flight battery and follow flight battery
instructions
Flight conditions may be too cold
Make sure battery is warm before use
Battery capacity too low for flight conditions
LED on receiver flashes and Transmitter too near aircraft during binding
aircraft will not bind to
process
transmitter (during binding)
LED on receiver flashes
rapidly and aircraft will
not respond to transmitter
(after binding)
Control surface does
not move
Bind switch or button not held while transmitter
was powered on
Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter
Less than a 5-second wait between first
powering on transmitter and connecting flight
battery to aircraft
Aircraft bound to different model memory
(ModelMatchTM radios only)
Flight battery/transmitter battery charge is too
low
Transmitter may have been bound to a different
model (or with a different DSM Protocol)
Aircraft or transmitter is too close to large metal
object, wireless source or another transmitter
Replace battery or use a larger capacity battery
Power off transmitter, move transmitter a larger
distance from aircraft, disconnect and reconnect flight
battery to aircraft and follow binding instructions
Power off transmitter and repeat bind process
Move aircraft and transmitter to another location and
attempt binding again
Leaving transmitter on, disconnect and reconnect flight
battery to aircraft
Select correct model memory on transmitter and
disconnect and reconnect flight battery to aircraft
Replace/recharge batteries
Select the right transmitter or bind to the new one
Move aircraft and transmitter to another location and
attempt linking again
Control surface, control horn, linkage or
servo damage
Replace or repair damaged parts and adjust controls
Wire damaged or connections loose
Do a check of wires and connections; connect or replace
as needed
Flight battery charge is low
Fully recharge flight battery
Control linkage does not move freely
Make sure control linkage moves freely
Controls reversed
Transmitter settings reversed
Motor loses power
Damage to motor, propeller shaft or power
components
Nut on prop shaft is too tight
Do the Control Direction Test and adjust controls on
transmitter appropriately
Do a check of motor, prop shaft and power components
for damage (replace as needed)
Loosen prop shaft nut until propeller shaft turns freely
Motor power quickly
decreases and increases
then motor loses power
Battery power is down to the point of receiver/
ESC Low Voltage Cutoff (LVC)
Recharge flight battery or replace battery that is no
longer performing
Servo locks or freezes at
full travel
Travel adjust value is set above 100% overdriving Set Travel adjust to 100% or less
the servo
EN
13
Limited Warranty
What this Warranty Covers
Horizon Hobby, Inc. (“Horizon”) warrants to the original purchaser
that the product purchased (the “Product”) will be free from defects in
materials and workmanship at the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation
or maintenance, (iii) modification of or to any part of the Product, (iv)
attempted service by anyone other than a Horizon Hobby authorized
service center, (v) Product not purchased from an authorized Horizon
dealer, or (vi) Product not compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO
OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS
ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE
PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy
shall be that Horizon will, at its option, either (i) service, or (ii) replace,
any Product determined by Horizon to be defective. Horizon reserves
the right to inspect any and all Product(s) involved in a warranty
claim. Service or replacement decisions are at the sole discretion of
Horizon. Proof of purchase is required for all warranty claims. SERVICE
OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL
OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH
CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT
LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no
event shall the liability of Horizon exceed the individual price of the
Product on which liability is asserted. As Horizon has no control over
use, setup, final assembly, modification or misuse, no liability shall be
assumed nor accepted for any resulting damage or injury. By the act of
use, setup or assembly, the user accepts all resulting liability. If you as
the purchaser or user are not prepared to accept the liability associated
with the use of the Product, purchaser is advised to return the Product
immediately in new and unused condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of
law principals). This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. Horizon
reserves the right to change or modify this warranty at any time
without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product
has been started, you must contact your local distributor or Horizon
directly. This will enable Horizon to better answer your questions and
service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.
com, submit a Product Support Inquiry, or call 877.504.0233 toll free
to speak to a Product Support representative.
14
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in
the country you live and use the Product in, please use the Horizon
Online Service Request submission process found on our website or
call Horizon to obtain a Return Merchandise Authorization (RMA)
number. Pack the Product securely using a shipping carton. Please
note that original boxes may be included, but are not designed to
withstand the rigors of shipping without additional protection. Ship
via a carrier that provides tracking and insurance for lost or damaged
parcels, as Horizon is not responsible for merchandise until it arrives
and is accepted at our facility. An Online Service Request is available at
http://www.horizonhobby.com/content/_service-center_render-service-center. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for
submitting your product for service. When calling Horizon, you will be
asked to provide your complete name, street address, email address
and phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA number,
a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have
any issue with a LiPo battery, please contact the appropriate
Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be serviced or
replaced free of charge. Service or replacement decisions are at the
sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be
completed and payment will be required without notification
or estimate of the expense unless the expense exceeds 50%
of the retail purchase cost. By submitting the item for service you
are agreeing to payment of the service without notification. Service
estimates are available upon request. You must include this request
with your item submitted for service. Non-warranty service estimates
will be billed a minimum of ½ hour of labor. In addition you will be
billed for return freight. Horizon accepts money orders and cashier’s
checks, as well as Visa, MasterCard, American Express, and Discover
cards. By submitting any item to Horizon for service, you are agreeing
to Horizon’s Terms and Conditions found on our website http://www.
horizonhobby.com/content/_service-center_render-service-center.
NOTICE: Horizon service is limited to Product compliant in the
country of use and ownership. If non-compliant product is
received by Horizon for service, it will be returned unserviced
at the sole expense of the purchaser.
EN
Warranty and Service Information
Country of Purchase
Horizon Hobby
Address
Phone Number/Email Address
United States
of America
Horizon Service
Center (Electronics
and engines)
Horizon Product
Support (All other
products)
United Kingdom
Horizon Hobby
Limited
Germany
Horizon Technischer
Service
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom
Christian-Junge-Straße 1
25335 Elmshorn, Germany
877-504-0233
Online Repair Request visit:
www.horizonhobby.com/service
France
Horizon Hobby SAS
11 Rue Georges Charpak
77127 Lieusaint, France
+33 (0) 1 60 18 34 90
infofrance@horizonhobby.com
China
Horizon Hobby –
China
Room 506, No. 97
Changshou Rd.
Shanghai, China, 200060
+86 (021) 5180 9868
info@horizonhobby.com.cn
877-504-0233
productsupport@horizonhobby.com
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
+49 (0) 4121 2655 100
service@horizonhobby.de
Compliance Information for the European Union
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2011052704
Product(s):
Item Number(s):
Equipment class:
PKZ Ultra Micro Pole Cat BNF
PKZU1480
1
The object of declaration described above is in conformity with the requirements of the
specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC
and EMC Directive 2004/108/EC
EN 301 489-1 V1.7.1: 2006
EN 301 489-17 V1.3.2: 2008
EN55022: 2006,
EN55024: 1998+A1: 2001+A2: 2003
(EN61000-4-2: 2001, EN61000-4-3: 2006, EN61000-4-8: 2001)
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
May 27, 2011
Steven A. Hall
Executive Vice President and Chief Operating Officer
International Operations and Risk Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s
responsibility to dispose of their waste equipment by handing it over to a
designated collections point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the
time of disposal will help to conserve natural resources and ensure that it is recycled
in a manner that protects human health and the environment. For more information
about where you can drop off your waste equipment for recycling, please contact your local city
office, your household waste disposal service or where you purchased the product.
EN
15
Parts Contact Information • Kontaktinformationen für Ersatzteil
• Coordonnées (pièces) • Recapiti dei distributori
Country of Purchase Horizon Hobby
Address
United States
Sales
4105 Fieldstone Rd
800-338-4639
Champaign, Illinois, 61822 USA sales@horizonhobby.com
Phone Number/Email Address
United Kingdom
Horizon Hobby Limited
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
Germany
Horizon Hobby GmbH
Christian-Junge-Straße 1
25335 Elmshorn, Germany
+49 (0) 4121 2655 100
service@horizonhobby.de
France
Horizon Hobby SAS
11 Rue Georges Charpak
77127 Lieusaint, France
+33 (0) 1 60 18 34 90
infofrance@horizonhobby.com
China
Horizon Hobby –
China
Room 506, No. 97
Changshou Rd.
Shanghai, China, 200060
+86 (021) 5180 9868
info@horizonhobby.com.
cn
Replacement Parts • Ersatzteile • Pièces de rechange
• Pezzi di ricambio
Part # • Nummer
Description
Numéro • Codice
Beschreibung
Description
Descrizione
PKZU1402
Decal Sheet: Ultra
Micro Pole Cat
Dekorbogen: Ultra
Micro Pole Cat
Planche de
décalcomanies :
Ultra Micro Pole Cat
Foglio con
decalcomanie:
Ultra Micro Pole Cat
PKZU1403
Landing Gear: Ultra
Micro Pole Cat
Parkzone Fahrwerk:
Ultra Micro Pole Cat
Train d’atterrissage :
Ultra Micro Pole Cat
Carrello di atterraggio:
Ultra Micro Pole Cat
PKZU1407
Tail Wheel: Ultra
Micro Pole Cat
Parkzone Spornrad:
Ultra Micro Pole Cat
Roulette de queue :
Ultra Micro Pole Cat
Ruotino di coda: Ultra
Micro Pole Cat
PKZU1408
Spinner (3): Ultra
Micro Pole Cat
Spinner (3): Ultra
Micro Pole Cat
Cône d’hélice (3) :
Ultra Micro Pole Cat
Spinner (3): Ultra
Micro Pole Cat
PKZU1420
Main Wing: Ultra
Micro Pole Cat
Tragfläche : Ultra
Micro Pole Cat
Aile principale : Ultra
Micro Pole Cat
Ala Principale: Ultra
Micro Pole Cat
PKZU1422
Aileron Pushrod
Linkage: UM Pole Cat
Querruderanlenkung
: Ultra Micro Pole Cat
Liaison de biellette
d’aileron : UM Pole Cat
Asta di spinta e
leveraggi dell’alettone:
UM Pole Cat
PKZU1425
Complete Tail w/
Accessories: UM
Pole Cat
Leitwerk m. Zubehör:
Ultra Micro Pole Cat
Queue complète
avec accessoires :
UM Pole Cat
Coda completa di
accessori: UM Pole Cat
PKZU1426
Pushrod Set: Ultra
Micro Pole Cat
Gestängeset: Ultra
Micro Pole Cat
Jeu de biellettes
mécaniques : Ultra
Micro Pole Cat
Set asta di spinta: Ultra
Micro Pole Cat
PKZU1467
Fuselage: Ultra Micro
Pole Cat
Rumpf: Ultra Micro
Pole Cat
Fuselage : Ultra Micro
Pole Cat
Fusoliera: Ultra Micro
Pole Cat
HBZ4929
Gearbox (No Motor):
Champ, UM T28,
Corsair
Getriebe (ohne Motor): Champ, UM T28,
Corsair
Réducteur (sans
moteur) : Champ,
UM T28, Corsair
Riduttore (senza
motore): Champ,
UM T28, Corsair
PKZ3528
Propeller Shaft:
Sukhoi Su-26m,
Micro P-51
Luftschraubenwelle:
Micro Sukhoi, Micro
P51
Arbre d’hélice :
Sukhoi Su-26m,
Micro P-51
Albero dell’elica:
Sukhoi Su-26m,
Micro P-51
EFL9052
Motor: UMX 4site/
Extra 300 3D
Motor: UMX 4site/
Extra 300 3D
Moteur : UMX 4site/
Extra 300 3D
Motore UMX 4site/
Extra 300 3D
EFLC1000
AC/DC 3.7V Li-Po
Charger
AC/DC-3,7V-Li-PoLadegerät
Chargeur Li-Po
CA/DC 3,7V
Caricabatterie Li-Po
CA/CC da 3,7V
58
Part # • Nummer
Description
Numéro • Codice
Beschreibung
Description
Descrizione
EFLB1501S25
1S 3.7V 150mAh
Li-Po Battery
1S-3,7V-150mAh-LiPo-Akku
Batterie Li-Po
150 mAh 3,7V 1S
Batteria Li-Po 1S
da 3,7V, 150 mAh
EFLH1067
Replacement Servo
Retaining Collars
Ersatzsicherung
für Servo
Bagues de maintien
de servo de rechange
Collarini di fissaggio
del servo di ricambio
EFLH1066
Replacement Servo
Mechanics: Short
Throw
Ersatzeinheit Servomechanik: kleiner
Ausschlag
Pièces de rechange
mécaniques servo :
course courte
Servo di ricambio
Meccanica: corta
Escursione
EFL9051
Prop and Spinner
130 x 70 (2): UM
4-Site/Champ
Propeller und Spinner
130 x 70 (2): UM
4-Site/Champ
Hélice et cône
d’hélice 130 x 70 (2) :
UM 4-Site/Champ
Elica e ogiva 130 x 70
(2): UM 4-Site/Champ
EFL9054
Prop Shaft with Gear
(2): UMX 4Site
Luftschraubenwelle
mit Getriebe (2): UMX
4Site
Arbre d’hélice avec
réducteur (2) : UMX 4Site
Albero dell’elica con
riduttore (2): UMX 4Site
SPMAR6410L
AR6410L DSM2/
DSMX 6-Channel
Ultra Micro Receiver/
ESC
AR6410L-DSM2/
DSMX-6-Kanal UltraMikro-Empfänger/ESC
Récepteur/ESC DSM2/
DSMX AR6410L
6 voies Ultra Micro
Ricevitore/ESC
AR6410L a 6 canali
Ultra Micro DSM2/
DSMX
2.3-Gram Performance Linear Long
Throw Servo
Spektrum 2;3-Gram
Performance Linear
Servo m. langem
Ruderweg
Servo linéaire 2.3g
longue course
Servo lineare a corsa
lunga 2.3-Gram
Replacement Servo
Mechanics: 2.3Gram 2030L
Spektrum
Ersatzgetriebe Servo:
2.3-Gram 2030L
Mécanique de
remplacement pour
servo 2.3g 2030L
Meccanica di ricambio
per servo: 2.3- Gram
2030L
SPMSA2030L
SPM6836
Optional Parts and Accessories • Optionale Bauteile und Zubehör •
Pièces et accessoires optionnels • Componenti e accessori opzionali
Part # | Nummer
Description
Numéro | Codice
Beschreibung
Description
Descrizione
EFLC1004
Celectra 4-Port 1S
3.7V 0.3 A DC Li-Po
Charger
E-flite E-flite 4 Port
Ladegerät 1S 3;7V
0;3A
Chargeur Li-Po
CC 0,3 A 3, 7V 1S
4 ports Celectra
Caricabatterie Li-Po
1S da 3,7V 0,3 A CC,
a 4 porte, Celectra
EFLC1005/AU/
EU/UK
AC to 6V DC 1.5
amp Power Supply
(Based upon your
sales Region)
AC zu 6V DC 1,5
Ampere Netzstecker
(Basierend nach
Vertriebsregion)
Alimentation CA
vers 6 V CC, 1,5 A
(En fonction de
votre région)
Alimentatore da CA
a 6 V CC, 1,5 Amp (in
base al Paese di vendita)
DX4e DSMX
4-channel
Transmitter
Spektrum DX4e
DSMX 4 Kanalsender
ohne Empfänger
Emetteur DX4e
DSMX 4 voies
DX4e DSMX
Trasmettitore 4 canali
DX5e DSMX
5-channel
Transmitter
Spektrum DX5e
DSMX 5 Kanalsender
ohne Empfänger
Emetteur DX5e
DSMX 5 voies
DX5e DSMX
Trasmettitore 5 canali
DX6i DSMX 6-Channel Transmitter
DX6i DSMX 6-Kanal
Sender
Emetteur DX6i
DSMX 6 voies
DX6i DSMX
Trasmettitore 6 canali
DX7s DSMX
7-Channel
Transmitter
Spektrum DX7s
7 Kanal Sender
Emetteur DX7s
DSMX 7 voies
DX7s DSMX
Trasmettitore 7 canali
DX8 DSMX
Transmitter
Spektrum DX8 nur
Sender
Emetteur DX8 DSMX
8 voies
DX8 DSMX Solo
trasmettitore
59
© 2012 Horizon Hobby, Inc.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
ParkZone, E-flite, JR, Celectra, DSM, ModelMatch
are trademarks or registered trademarks of Horizon Hobby, Inc.
Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.
US D578,146. PRC ZL 200720069025.2. US 7,898,130 Other patents pending.
www.parkzone.com
Created 10/12 29101.1X
60
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising