advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Small Secure Storage Shelf for Carts and Stands
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC730A/B/C
PAC730A/B/C
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
Installation Instructions
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components stored within or on the PAC730 does not exceed 25 lbs (11.3 kg).
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
2
Installation Instructions
DIMENSIONS
PAC730A/B/C
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
MEASUREMENTS: [MILLIMETERS]
INCHES
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
3
PAC730A/B/C
TOOLS FOR INSTALLATION / PARTS
5/32"
(Included)
A (1)
[Storage Shelf]
Installation Instructions
B (1)
[Pole Attachment Plate]
C (1)
[Upper Bracket] D (1)
[Hole Plug]
G (8)
[Bumper]
E (1)
5/32"
F (4)
1/4-20 x 3/8"
H (4)
1/4-20 x 3/4"
J (1)
[Key]
4
Installation Instructions
INSTALLATION
NOTE: The PAC730 may be mounted on the Chief cart or stand either by being attached mid-column on the cart or stand column, or to the top of the cart or stand column.
Mid-Column Attachment
1.
Attach pole attachment plate (B) around the cart or stand column to the storage shelf (A) using four 1/4-20 x 3/8" button head cap screws (F). (See Figure 1)
2.
Proceed to Adding Bumpers section.
(A)
1 (F) x 4
(B)
Hole
Pattern
PAC730A/B/C
1 (H) x 4
Cart/Stand
Column
Figure 1
Top of Column Attachment
1.
Attach upper bracket (C) to storage shelf (A) using four
1/4-20 x 3/4" button head cap screws (H). (See Figure 2)
NOTE: The upper bracket (C) may be attached in two different ways using the two hole patterns on the storage shelf bottom. (See Figure 2)
Figure 2
2.
Remove display from faceplate following instructions in the cart or stand installation instructions.
5
PAC730A/B/C
3.
Remove and save four button head cap screws from top of cart or stand column. (See Figure 3)
4.
Place upper bracket with PAC730 onto top of cart or stand column. (See Figure 3)
5.
Fasten PAC730 to cart or stand using four button head cap screws removed in Step 3. (See Figure 3)
3
5
Faceplate x 4
(A)
4
4
Cart/Stand
Column
(G) x 8
Cable
Management
Opening
Installation Instructions
Figure 4
[Bottom View]
Figure 3
6.
Re-attach display to faceplate following installation instructions included with cart or stand.
Adding Bumpers
Add eight bumpers (G) to fill the unused PEM nuts (inside the
PAC730) to protect the stored equipment. They can be added to the unused PEM nuts in the circled areas. (See Figure 4)
Cable Management
1.
Run cables from components in storage shelf through the cable management opening at the back of the storage shelf.
(See Figure 4)
2.
If cable management opening is not used, close the hole with the hole plug (D).
6
Installation Instructions PAC730A/B/C
7
PAC730A/B/C Installation Instructions
Chief Manufacturing, a products division of Milestone AV Technologies
8807-002013 Rev01
2009 Milestone AV Technologies, a
Duchossois Group Company www.chiefmfg.com
10/09
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
Europe
F 877.894.6918 / 952.894.6918
A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
Asia Pacific
F +31 (0)40 2668615
A Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F +86-755-8996 9217
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project