Use, Care, and Installation Guide Guide d`utilisation, d`entretien et d

Use, Care, and Installation Guide Guide d`utilisation, d`entretien et d
Use, Care, and Installation Guide
Guide d’utilisation, d’entretien et d’installation
Guía de instalación, uso y mantenimiento
READ AND SAVE THESE INSTRUCTIONS
LISEZ CES INSTRUCTIONS ET CONSERVEZ-LES
LEA Y GUARDE ESTAS INSTRUCCIONES
READ AND SAVE THESE INSTRUCTIONS
Important safety Notice
WARNING
CAUTION
TO REDUCE THE RISK OF INJURY TO PERSONS, IN
THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING:
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet,
or other metal tray, then turn off the gas burner or the
electric element. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - you may be burned.
c) DO NOT USE WATER, including wet dishcloths or
towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a class ABC extinguisher, and you
already know how to operate it.
2) The fire is small and contained in the area where it
started.
3) The fire department is being called.
4) You can fight the fire with your back to an exit.
FOR GENERAL VENTILATING USE ONLY. DO NOT USE
TO
EXHAUST
HAZARDOUS
OR
EXPLOSIVE
MATERIALS OR VAPOURS.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the
manufacturer.
If you have questions, contact the
manufacturer.
B. Before servicing or cleaning the unit, switch power off at
service panel and lock service panel disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
C. Installation Work and Electrical Wiring Must Be Done By
Qualified Person(s) In Accordance With All Applicable
Codes & Standards, Including Fire-rated Construction.
D. Sufficient air is needed for proper combustion and
exhausting of gases through the flue (Chimney) of fuel
burning equipment to prevent back- drafting. Follow the
heating equipment manufacturers guideline and safety
standards such as those published by the National Fire
Protection Association (NFPA), the American Society for
Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
E. When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
F. Ducted systems must always be vented to the outdoors.
The manufacturer declines all responsibility in the event of
failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The
manufacturer further declines all responsibility for injury due
to negligence and the warranty of the unit automatically
expires due to improper maintenance.
CAUTION
CAUTION
To reduce risk of fire and to properly exhaust air, be
sure to duct air outside - do not vent exhaust air into
spaces within walls, ceilings, attics, crawl spaces, or
garages.
Automatically Operated Device - To Reduce The Risk Of
Injury Disconnect From Power Supply Before Servicing.
OPERATION
a. Always leave safety grills and filters in place. Without
these components, operating blowers could catch onto hair,
fingers and loose clothing.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL
DUCT WORK.
Install this hood in accordance with all requirements
specified.
WARNING
To Reduce The Risk Of Fire Or Electric Shock, Do Not
Use This Hood With Any External Solid State Speed
Control Device.
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE.
a) Never leave surface units unattended at high settings.
Boilovers cause smoking and greasy spillovers that may
ignite. Heat oils slowly on low or medium settings.
b) Always turn hood ON when cooking at high heat or when
flambeing food (I.e. Crepes Suzette, Cherries Jubilee,
Peppercorn Beef Flambe’).
c) Clean ventilating fans frequently. Grease should not be
allowed to accumulate on fan or filter.
d) Use proper pan size. Always use cookware appropriate
for the size of the surface element.
3
Electrical & Installation requirements
Electrical requirements
Before installing the hood
IMPORTANT
1. For the most efficient air flow exhaust, use a straight run
or as few elbows as possible.
CAUTION: Vent unit to outside of building, only.
Observe all governing codes and ordinances.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
— latest edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.0-M91 - latest
edition** and all local codes and ordinances.
2. At least two people are necessary for installation.
3. Fittings material is provided to secure the hood to most
types of walls/ceilings, consult a Qualified Installer,
check if they perfectly fit with your cabinet/wall.
4. Do not use flex ducting.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
5. COLD WEATHER installations should have an additional
backdraft damper installed to minimize backward cold air
flow and a nonmetallic thermal break to minimize
conduction of outside temperatures as part of the
ductwork. The damper should be on the cold air side of
the thermal break.
The break should be as close as possible to where the
ducting enters the heated portion of the house.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure range
hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
IMPORTANT
6. Make up air: Local building codes may require the use of
Make-Up Air Systems when using Ducted Ventilation
Systems greater than specified CFM of air movement.
The specified CFM varies from locale to locale. Consult
your HVAC professional for specific requirements in your
area.
Removing the packaging
Save Installation Instructions for electrical inspector’s use.
The range hood must be connected with copper wire only.
The range hood should be connected directly to the fused
disconnect (Or circuit breaker) box through metal electrical
conduit.
CAUTION!
Remove carton carefully, Wear gloves to protect against
sharp edges.
Wire sizes must conform to the requirements of the National
Electrical Code ANSI/NFPA 70 — latest edition*, or CSA
Standards C22.1-94, Canadian Electrical Code Part 1 and
C22.2 No. 0-M91 - latest edition** and all local codes and
ordinances.
WARNING!
Remove the protective film covering the product before
putting into operation.
A U.L.- or C.S.A.-listed conduit connector must be provided
at each end of the power supply conduit (at the range hood
and at the junction box).
Copies of the standards listed may be obtained from:
* National Fire Protection Association Batterymarch Park Quincy,
Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road Cleveland,
Ohio 44131-5575
4
List of Materials
Parts supplied
Parts not supplied
Removing the packaging
Optional Accessories
CAUTION!
Remove carton carefully, Wear gloves to protect against
sharp edges.
WARNING!
Remove the protective film covering the product before
putting into operation.
• Hood canopy assembly with blower, transition.
• Lamp already installed.
• Grease filter.
• Duct cover.
• Hardware bag with:
• Template.
• Duct cover support bracket (1 piece)
• Use, care and installation guide
• Wood screws (6 pieces - 3/16" x 1" 3/4)
• Hood attachment anchors screws (6 pieces - 1/8" x
3/8")
• Assembly screws (8 pieces)
•
Ductless Recirculating Kit
To be used only in the Ductless (Recirculating)
version
includes: charcoal filter, charcoal filter support and
fixing bracket, deflector
•
Professional Stainless Steel Grease filter
Tools/Materials required
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
Wire nuts
Tape to mount template
8" rounded metal duct length to suit installation
Measuring tape
Pliers
Gloves
Knife
Safety glasses
Electric drill with 5/16” and 3/8” Bits
Strain relief
Spirit level
Duct tape
Screwdrivers:
Phillips (Posidrive) # 2
Torx # 2
Wire cutter/stripper
Masking tape
Hammer
Saw, jig saw or reciprocating saw
Dimensions and Clearances
*Ductless (Recirculating) version Only
**Ducting version Only
6
Ducting Options and Examples
Closely follow the instructions set out in this manual.
All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this
manual, is declined.
Venting methods
The hood is equipped with a transition B for discharge of fumes to the outside (Ducting version).
Should it not be possible to discharge cooking fumes and vapour to the outside, the hood can be used in the Ductless
(Recirculating) version. Attach a charcoal filter and the deflector F on the duct cover support bracket G. Fumes and vapours
are recycled through the top grille H by means of a duct connected to the transition B and the transition mounted on the
deflector F.
NOTE: For ductless (Recirculating) version only: purchase the Ductless Recirculating Kit.
Minimum Duct Size (Ducting/Ductless version): 8" Round Pipe.
Preparation
Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be
constructed.
Fittings material is provided to secure the hood to most types of walls/ceilings.
However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling.
Before making cutouts, make sure there is proper clearance within the ceiling or wall for exhaust vent.
Hood installation height above cooktop is the users preference. The lower the hood is above the cooktop, the more efficient the
capturing of cooking odors, grease and smoke.
CAUTION: FOR GAS RANGES INSTALLATION: MOUNT THIS HOOD SO THAT THE BOTTOM EDGE IS AT 30" (76,2 CM)
ABOVE THE COOKING SURFACE.
FOR ELECTRIC RANGES INSTALLATION: MOUNT THIS HOOD SO THAT THE BOTTOM IS NOT LESS THAN 24" (61 CM)
AND NOT MORE THAT 30" (76,2 CM) ABOVE THE COOKING SURFACE.
HOUSEHOLD USE. PLEASE, READ INSTALLATION MANUAL FOR SPECIFIC APPLICATION.
Check your ceiling height and the hood height maximum before you select your hood.
7
Installation
Installation - Ducting version
•
If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall. Otherwise put a thick, protective covering over
countertop, cooktop or range to protect from damage
and debris. Select a flat surface for assembling the unit.
Cover that surface with a protective covering and place
all canopy hood parts and hardware in it.
•
Determine and mark the centerline on the wall where the
canopy hood will be installed.
•
Select a mounting height comfortable for the user and
mark on wall.
•
Tape template, matching center-line and hood bottom.
Ceiling ducting
If the duct will vent straight up to the ceiling:
• Use level to draw a line straight up, from the centerline
on the template to the ceiling.
• Measure at least 4 -5/8 ” from the back wall to the circle
center of an 8-½” hole on the ceiling.
Wall ducting
If ductwork will vent to rear:
Note: for minimum duct cover extension we suggest to use
a round to rectangle duct adapter.
• Use a level to draw a line straight up from the centerline
on the template.
• Measure at least 26 - 1/2" (the measure might vary
dependig on the elbow used) above the pencil line that
indicates the bottom installation height, to the circle
center of an 8-½” diameter duct hole (Hole may be
elongated for duct elbow).
Mounting the duct cover bracket
The duct bracket should be installed against the back wall
and flush with the ceiling.
This bracket will hold the telescopic duct cover in place at
the top.
House wiring location
• The junction box is located on the top left side of the
hood.
• Wiring should enter the back wall at least 20 - 1/4"
above the bottom of the installation height, and within 75/8" and 4-7/8"of the left side of the centerline.
Secure the bracket to the wall:
• Align the marked centerline on the bracket with the
centerline on the wall.
• Mark 2 screw hole locations in the wall.
• Drill 5/16" pilot holes in the marked locations.
• Install wall fastener anchors.
• Drive wood screws, by hand, into the fastener to allow
anchors to expand. Remove the screws.
• Secure the bracket to the wall with wood screws and/or
fasteners.
8
Install framing for hood support
•
If drywall is present, mark the screw hole locations.
Remove the template.
• Cut away enough drywall to expose 2 vertical studs at
the holes location indicated by the template.
Install two horizontal supports at least 4" X 2" between
two wall studs at the bottom and upper mounting holes
installation location.
• The horizontal support must be flush with the room side
of the studs.
Use cleats behind both sides of the support to secure to
wall studs.
• Reinstall drywall and refinish.
IMPORTANT- Framing must be capable of supporting
100 lbs.
•
Mark “lower” wood
screw holes locations
in the wall using a
pencil.
•
•
•
•
•
Remove the hood.
Drive “lower” wood screws, by hand. Remove screws.
Mount the hood onto the “upper” screws.
Drive and tighten the “upper” wood screws, by hand.
Drive and tighten the “lower” wood screws, by hand.
Mounting the hood
Install the 8” round transition as shows the image below.
The installation screws and the 8” round transition are
included on the hood package.
8”
Connecting the ductwork
• Install ductwork, making connections in the direction of
airflow as illustrated.
• Push duct over the exhaust outlet.
• Wrap all duct joints and the flange connections with duct
tape for an airtight seal.
• Make the same connection in the wall or ceiling vent exit.
WARNING: 2 people are require d to lift and position the
hood onto the mounting screws.
• Place the template on the wall along the horizontal line,
make sure the template is leveled and centered with the
centerline.
• Mark “upper” screw holes locations in the wall.
• IMPORTANT. Check to be sure that hole locations are
leveled and correctly centered by the vertical centerline.
• Drive “upper” wood screws by hand. Leave ¼ “ of
distance between the screw head and the wall.
• Remove the grease filter and mount the hood onto the
“upper” screws.
9
Electrical connection
Mounting the duct cover
Note: Upper Duct Cover may be placed upside down to
hide (or unhide) louver holes.
• Position the duct cover over the mounted hood.
• Slide the bottom of the duct into the canopy area.
• Position the top of the duct over the duct mounting
bracket. If a telescopic duct cover is used, grab the
upper part of the telescopic duct cover, pull it and place
it in the duct cover mounting bracket.
• Secure the top of the duct with 2 assembly screws
provided.
WARNING
Electrical Shock Hazard
Warning: Turn off power circuit at the service panel
before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE
MUST BE CONNECTED TO THE GROUNDING WIRE
IN YOUR HOME ELECTRICAL SYSTEM, AND IT
MUST UNDER NO CIRCUMSTANCES BE CUT OR
REMOVED.
Failure to do so can result in death or electrical
shock.
Facing the front of the range hood, remove the left
knockout and the Junction box cover and install the
conduit connector (cULus listed) in junction box.
Knockout
Junction box
cover
•
Secure the bottom of the duct with 2 assembly screws
provided.
• If not already done, install 1/2” conduit connector in j-box.
Metal electrical
conduit
Install the grease filter and turn power on at service panel.
Check operation of the hood.
House
wiring
If range hood does not operate:
UL listed
wire nut
•
•
Check that the circuit breaker is not tripped or the house
fuse blown.
Disconnect power supply. Check that wiring is correct.
To get the most efficient use from your new range hood,
read the “Use and Care Information” section.
Keep your Installation Instructions and Use and Care
Guide close to range hood for easy reference.
10
Installation - Ductless (Recirculating) version
House wiring location
The junction box is located on the top left side of the
hood.
Wiring should enter the back wall at least 20 - 1/4"
above the bottom of the installation height, and within 75/8" and 4-7/8"of the left side of the centerline.
CAUTION
To install the hood in this version, first purchase the
Ductless Recirculating Kit.
includes: charcoal filter and deflector
If possible, disconnect and move freestanding or slide-in
range from cabinet opening to provide easier access to
rear wall. Otherwise put a thick, protective covering over
countertop, cooktop or range to protect from damage
and debris. Select a flat surface for assembling the unit.
Cover that surface with a protective covering and place
all canopy hood parts and hardware in it.
Install framing for hood support
If drywall is present, mark the screw hole locations.
Remove the template.
Cut away enough drywall to expose 2 vertical studs at
the holes location indicated by the template.
Install two horizontal supports at least 4" X 2" between
two wall studs at the bottom and upper mounting holes
installation location.
The horizontal support must be flush with the room side
of the studs.
Use cleats behind both sides of the support to secure to
wall studs.
Reinstall drywall and refinish.
IMPORTANT- Framing must be capable of supporting
100 lbs.
Determine and mark the centerline on the wall where the
canopy hood will be installed.
Select a mounting height comfortable for the user and
mark on wall.
Tape template, matching center-line and hood bottom.
Mounting the duct cover bracket
The duct bracket should be installed against the back wall
and flush with the ceiling.
This bracket will hold the telescopic duct cover in place at
the top.
Secure the bracket to the wall:
Align the marked centerline on the bracket with the
centerline on the wall.
Mark 2 screw hole locations in the wall.
Drill 5/16" pilot holes in the marked locations.
Install wall fastener anchors.
Drive wood screws, by hand, into the fastener to allow
anchors to expand. Remove the screws.
Secure the bracket to the wall with wood screws and/or
fasteners.
Mounting the hood
Install the 8” round transition as shows the image below.
The installation screws and the 8” round transition are
included on the hood package.
8”
11
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
12
Mounting the duct cover
Note: Upper Duct Cover may be placed upside down to
hide (or unhide) louver holes.
Position the duct cover over the mounted hood.
Slide the bottom of the duct into the canopy area.
Position the top of the duct over the duct mounting
bracket. If a telescopic duct cover is used, grab the
upper part of the telescopic duct cover, pull it and place
it in the duct cover mounting bracket.
Secure the top of the duct with 2 assembly screws
provided.
Electrical connection
WARNING
Electrical Shock Hazard
Warning: Turn off power circuit at the service panel
before wiring this unit.
120 VAC, 15 or 20 Amp circuit required.
ELECTRICAL GROUNDING INSTRUCTIONS
THIS APPLIANCE IS FITTED WITH AN ELECTRICAL
JUNCTION BOX WITH 3 WIRES, ONE OF WHICH
(GREEN/YELLOW) SERVES TO GROUND THE
APPLIANCE. TO PROTECT YOU AGAINST
ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE
MUST BE CONNECTED TO THE GROUNDING WIRE
IN YOUR HOME ELECTRICAL SYSTEM, AND IT
MUST UNDER NO CIRCUMSTANCES BE CUT OR
REMOVED.
Failure to do so can result in death or electrical
shock.
Facing the front of the range hood, remove the left
knockout and the Junction box cover and install the
conduit connector (cULus listed) in junction box.
Knockout
Junction box
cover
Secure the bottom of the duct with 2 assembly screws
provided.
If not already done, install 1/2” conduit connector in j-box.
Metal electrical
conduit
Install the charcoal filter on the back side of the grease filter,
install both on the range hood and turn power on at service
panel. Check operation of the hood.
House
wiring
If range hood does not operate:
UL listed
wire nut
Check that the circuit breaker is not tripped or the house
fuse blown.
Disconnect power supply. Check that wiring is correct.
To get the most efficient use from your new range hood,
read the “Use and Care Information” section.
Keep your Installation Instructions and Use and Care
Guide close to range hood for easy reference.
13
14
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
15
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
‡
16
Maintenance
ATTENTION! Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the
connector and removing the connector fuse.
Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.
Cleaning
Replacing the light bulb
Do not spray cleaners directly to the control while
cleaning the Hood.The cooker hood should be cleaned
regularly (at least with the same frequency with which you
carry out maintenance of the fat filters) internally and
externally. Clean using the cloth dampened with neutral
liquid detergent. Do not use abrasive products. DO NOT
USE ALCOHOL!
WARNING:
Failure to carry out the basic cleaning recommendations of
the cooker hood and replacement of the filters may cause
fire risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage
to the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
CAUTION
Before replacing the lamps, switch power off at service
panel and lock service panel disconnecting means to
prevent power from being switched on accidentally.
NOTE: Turn off the lights and fan. Allow the lights to
cool before handling. If new lights do not operate be
sure lights are inserted correctly before calling service.
Grease Filter
Traps cooking grease particles.
This must be cleaned once a month using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle. When
washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Bulb
Replace Lights
Remove the inner lamp lens cover by inserting a small
flat blade screwdriver into each of the three slots and
gently prying it free.
NOTE: Do not remove the outer trim ring (lamp
assembly).
Grasp the bulb and pull it straight out.
Replace with 120 volt, 40 watt halogen bulbs with a G9
base SUITABLE FOR USE IN OPEN LUMINAIRES.
Follow package directions, wear gloves, do not
touch bulb with your bare fingers.
Replace inner cover by inserting the three retaining tabs
into the three slots and pressing them firmly in place.
17
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement