Part # 11054099 58-64 Impala Rear CoolRide Kit

Part # 11054099 58-64 Impala Rear CoolRide Kit
350 S. St. Charles St. Jasper, In. 47546
Ph. 812.482.2932 Fax 812.634.6632
www.ridetech.com
Part # 11054099
58-64 Impala Rear CoolRide Kit
For Use w/ Factory Lower Arms
Components:
2
90006873
Rear air spring
1
90000463
Driver side upper air spring bracket
1
90000464
Passenger side upper air spring bracket
2
90000465
Lower air spring bracket
2
90000472
1.5” O.D x 1.5” long aluminum bump stop spacer
2
90001082
Short bump stop
Hardware:
2
99435001
7/16” x 6” stud
Upper air spring bracket to frame
2
99433002
7/16” SAE flat washer
Upper air spring bracket to frame
2
99432001
7/16” USS Nylok nut
Upper air spring bracket to frame
4
99372002
3/8” USS Nylok nut
Upper air spring bracket
8
99373003
3/8” flat washer
Air spring mounting / Bump stop
2
99371003
3/8” x 1” USS bolt
Bump stop
2
99371001
3/8” x 3/4” USS bolt
Lower air spring bracket
4
99373005
3/8” lock washer
Lower air spring bracket / Bump stop
2
99311001
5/16”-18 x 1” USS bolt
Lower air spring bracket to arm
2
99312003
5/16” Nylok nut
Lower air spring bracket to arm
2
99313002
5/16” flat washer
Lower air spring bracket to arm
Installation Instructions
******Must be used w/ RideTech shock kit******
1. Raise and support vehicle at a safe and comfortable working height.
2. Support axle then remove coil spring, shock, and bump stop. Refer to service manual for proper
disassembly procedure.
3. Apply thread sealant to the air
fitting and screw it into the top of the
air spring.
4. Place the upper cup bracket on top
of the air spring and secure with two
3/8” Nylok nuts and flat washers.
5. Thread the 6” stud into the nut in
the bottom of the cup.
6. Place the air spring assembly into
the coil spring pocket with the tab on
the side of the cup aligning with the
factory bump stop mount.
7. The stud should poke through the
hole in the upper coil spring pocket.
Some cars may not have this hole and
it must be drilled. Fasten with a 7/16”
Nylok nut and flat washer.
8. Fasten the aluminum bump stop
spacer to the frame using a 3/8” x 1”
bolt, flat washer and lock washer.
9. Screw the bump stop into the
spacer.
10. Bolt the lower mount to the
bottom of the air spring using a 3/8” x
3/4" bolt, lock washer and flat washer.
Before tightening, make sure it aligns
with the lower arm.
11. The hole in the tab on the lower
mount will align with the parking brake
cable clamp. It will be held tight with
a 5/16” x 1” bolt, lock washer, and flat
washer.
12. Make sure that the air spring
cannot rub on anything at anytime.
This will result in air spring failure
and is a not a warrantable situation.
13. Ride height on this air spring is
approximately 5” tall, but may vary to
driver preference.
This is the driver bracket looking down
at the top of it.
The tab goes to the rear of the car.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement