Digital Wireless Security System
Digital Wireless Security System
Models: 1DVRDIG502 / 1DVRDIG1502
EU Environmental Protection
Waste electrical products should not
be disposed of with household waste.
Please recycle where facilities exist.
Check with your local authority or
retailer for recycling advice.
Version 1.8
Welcome
Contents
Welcome
Features
Packing List
Structure
Installation
Operations
- Basic Operations
- Video Recording
- Playback
- Deleting Footage
- Outputting Video to TV/Monitor
System Setting
- Setting Date/Time
- Language
- Record Mode
- Formatting SD/USB
- Storage Device
- Display Preferences
- TV Standard
- System Information
- Firmware Update
- Scan Mode Period
- Mute
- Restore Defaults
- Brightness
- Volume
- Alarm Volume
- Power Saving Mode
Record
- Timer Recording
- Motion Detection
- PIR Detection
Playback
Camera
- Pairing
- Enable/Disable
- Picture in Picture
Alarm Settings
Specifications
FAQ
FCC Information
02
02
02
03
04
05
05
07
09
09
10
10
11
11
12
12
12
13
13
13
13
13
14
14
14
14
14
15
15
15
15
16
16
16
17
18
18
18
19
20
20
This product is a home/small office monitoring and recording device. It consists of
four cameras and one DVR (Digital Video Recorder) built in to a 7 inch LCD
monitor, which allows for split-screen view of all 4 cameras simultaneously.
Features
• 1-4 x Weather Resistant Digital Wireless Cameras
• 7 Inch LCD display with Digital Video Recording
• Simple Installation – No cables required!
• Encrypted connection between cameras and DVR for maximum privacy
• SD card support for up to 32GB (Class 6-10 SD)
• USB HDD support up to 1TB (Powered external drive required)
• 24/7 recording non-stop with overwrite function
• Supports Manual, Scheduled, or Motion Triggered recording
• Up to 30FPS video recording (10fps with 4 cameras)
• Video output to TV/Monitor
• Up to 300m range (assumes no interference and unobstructed line of sight)
Packing List
1.
2.
3.
4.
5.
1x Digital Wireless Camera
7” LCD Monitor
Camera PSU
Monitor PSU
TV Out Cable
Structure
Installation
1.
Install the camera at the desired location. The camera can be installed
in one of 2 ways:
2.
Connect the receiver at a central location if using multiple cameras, or
in the case of a single camera setup connect it as close to the camera as
possible.
3.
Insert the SD card or connect an external storage device. In the case of
USB hard drives, please ensure you are using an external power supply
(not a USB powered disk).
Notes:
1.
The monitor does not support ‘hot plugging’ of storage devices / SD
Cards. When you connect a new device, please reboot the monitor by
shutting it down and booting up again.
2.
The format used by the device is FAT32. Please ensure your devices are
formatted appropriately.
3.
Please ensure any connected storage devices are reformatted in the
monitor if they have been used with other devices.
Operations
5.
After successful pairing, the monitor should display an image similar to
the below:
6.
Press the
7.
Press the
button to enter cyclic display mode. The interval
between picture cycles can be set in the System menu (Page 13).
Basic Operation
1.
Connect the camera to a power supply. The power indicator should
light up:
2.
Connect the receiver to a power supply:
3.
Press the power button on the receiver (or remote if you purchased
one) for 2 seconds. The power indicator should light up and a loading
screen should appear on the screen.
4.
Pair the camera to the receiver. If you purchased a single camera
system, pairing should already be configured. For more information on
pairing, please refer to page 16 of this manual.
button to select between one of three display modes:
Video Recording
4.
Manual Recording:
1.
2.
3.
From the default monitoring screen (where you see the image coming
in from the cameras), press the left and right buttons to select the
camera you wish to record.
Press the record button on the device. A small recording icon
will appear, indicating that recording has started.
Press the record button again to finish recording.
Timer Recording:
Set the recording start/stop time in the “Timer Recording” menu (more info on
page 15). The device will automatically record during the times you have
configured and will save the footage to the storage device you have inserted.
Specific steps are as follows:
1.
2.
3.
Press the Menu button to access the main menu. Press the left or right
buttons to select “Record” and press the OK button.
Press the up or down buttons to select “Timer Recording” and press
OK.
Press the up or down buttons to select “New Schedule” and press OK:
After setting the record times the device will automatically record
accordingly. You can press the record button to stop the scheduled
recording if you choose.
PIR Recording:
This mode can be used to capture human or animal movement within 5m of the
camera. The specific steps are as follows:
1.
2.
3.
4.
5.
Press the Menu button to enter the recording interface. Press the left
and right buttons to select “Record” and press the OK button.
Press the up or down buttons to select “PIR Recording” and press OK.
Press the up or down buttons to select the camera.
Press the left or right button to switch PIR on/off.
Press the OK button to confirm and exit.
Motion Detection Recording:
This mode can be used to capture any movement within visual range of the
camera. The specific steps are as follows:
1.
2.
3.
4.
5.
Press the MENU button to enter the main menu, then press left or right
to select “Record” and press the OK button.
Press the left or right buttons to select “Motion Detection” and press
OK.
Press the up or down buttons to select a camera and press OK.
Press the up or down button to select an item, and the left or right
button to adjust the setting.
Press the OK button to confirm and exit.
Note: When “Off” is set for sensitivity, motion detection recording is off.
Press up or down to select
Press left or right to adjust
Press OK to confirm and exit
Please note that in all modes, recordings are broken down into 5 minute segments.
Playback
1.
2.
3.
Video Output
From the main viewing screen, press the Playback button on the
monitor to access the playback interface.
Press up or down to select the folder (footage is stored by date, with a
separate folder for each day).
Press the OK button to enter the selected folder:
The monitor can be connected to a larger TV/Monitor using the supplied AV cable:
Press the
button from the main view screen to switch between the built in
display and connected TV/Monitor. Please note you cannot receive an image on
both simultaneously.
4.
Press up or down to select the video you want to play, and press OK to
see it. During playback, you can use the left and right buttons to rewind
or fast forward, OK to pause, and Menu to end playback.
System Settings
From the main viewing screen, press the Menu button to enter the system
settings menu:
Deleting Footage
1.
2.
3.
4.
From the main viewing screen, press the Playback button on the
remote to access the playback interface.
Press Up or Down to select the folder (footage is stored by date, with a
separate folder for each day).
Press the OK button to enter the selected folder.
Press up or down to select the piece of footage you want to remove,
and press the
button to delete it.
Please note that folders can be deleted too using the same button, but only when
they are empty (all contained footage must be deleted first).
From here, press the left and right buttons to select an option and press OK.
Language
System
Date/Time
Language
Record Mode
Format USB/USB
Storage for
Recording
Display Items
TV System
System
Information
System Update
Scan mode period
Mute
Load Default
Brightness
Volume
Alarm Volume
Power Saving
Mode
Sets the system date and time.
Sets the system language.
Sets whether recording continues to record over old footage
when storage device is full, or stops.
Formats the selected storage device.
Selects the storage device to be used.
Sets which information elements appear on recorded
footage.
Switch between NTSC/PAL for external monitor.
Views information about the system.
1.
2.
Record Mode
1.
2.
3.
Used for updating firmware.
Sets the delay before switching to the next camera in cycle
mode.
Turns off the speaker.
Restores default configuration for all settings.
Adjust display brightness.
Sets speaker volume for camera microphones.
Set the volume for alarm notifications.
Sets whether to disable screen during inactive periods.
Press the up and down buttons to select a menu element, and OK to adjust.
Press OK to enter.
Press the Up or Down buttons to select language, then OK to confirm.
Press OK to enter.
Press the Up or Down buttons to select “Normal” (which stops
recording when storage device is full) or “Overwrite” (which
automatically records footage over the oldest stored recordings if the
storage device is full).
Press the OK button to confirm and exit.
Format SD/USB
1.
2.
3.
Press OK to enter.
Press the up or down buttons to select “SD Card”, “USB Device” or
“Cancel”:
SD Card: Formats the SD card
USB Device: Formats the connected USB device
Cancel: Exits the formatting menu
Press the OK button to begin formatting:
Date/Time
4.
Once formatting is complete, the monitor will read “Format Successful”
and will return you to the previous menu.
Storage for Recording
1.
2.
3.
Scan Mode Period
Press OK to enter.
Press the Up or Down buttons to select “SD Card” or “USB Device”.
Press the OK button to confirm and exit.
Display Items
1.
2.
3.
Press OK to enter.
Press the Up or Down buttons to select an item
Click the OK button to confirm whether or not to display this item. If
the following items are enabled, the icons below will appear:
When you have selected the items you want to see, press the MENU
button to confirm and exit.
TV System
1.
2.
1.
2.
3.
Press OK to enter.
Press Left or Right to set on or off.
Press OK to confirm and exit.
Load Defaults
1.
2.
3.
Press OK to enter.
Press Left or Right to select “Cancel” or “OK” – cancel makes no
changes, OK restores all of the device’s settings to their defaults.
Press OK to confirm your selection and exit.
Brightness
Press OK to enter.
Press Up or Down to select, then press OK to confirm and exit. Use PAL
for UK monitors.
System Information
1.
2.
Press OK to enter.
Press Left or Right to change the setting.
Press OK to confirm and exit.
Mute
Signal intensity
SD/USB status: Shows SD/USB connection status
Camera: Camera name
4.
1.
2.
3.
Press OK to enter and view the information.
Press Menu to exit.
System Update
Please contact technical support for information on firmware availability and
installation instructions.
1.
2.
3.
Press OK to enter.
Press Left or Right to decrease or increase the brightness.
Press OK to confirm and exit.
Volume
1.
2.
3.
Press OK to enter.
Press Left or Right to decrease or increase the speaker volume.
Press OK to confirm and exit.
Alarm Volume
1.
2.
3.
Press OK to enter.
Press Left or Right to decrease or increase the alarm output volume.
Press OK to confirm and exit.
Power Saving Mode
1.
2.
3.
4.
5.
Press OK to enter.
Press Up or Down to select “Time Interval” or “Wake up on Motion”.
Press OK to select.
Press Up or Down to change the setting.
Press OK to confirm and exit.
Record Settings
Motion Detection
Enable this mode to trigger recording based on movement. Please note that this
mode should not be used at the same time as PIR or Timer based recordings. For
more information, please refer to page 8.
PIR Recording
Enable this mode to trigger recording based on human/animal movement within
5m of the camera. Please note this mode should not be used at the same time as
Motion or Timer based recording. For more information, please refer to page 8.
Playback
From the main menu, use the Left and Right arrow buttons to select Playback, and
press OK to enter. For more information on using this feature, please refer to page
9.
From the main menu, press Left or Right to select “Record” and press OK:
Camera
From the main menu, use the left and right arrow buttons to select Camera, and
press OK:
Timer Recording
Use this mode to set the start/stop times for automatic recording. Please note
that these settings should not be used at the same time as PIR or Motion
recording (which are both 24/7 modes). For more information, please refer to
pages 7 & 8.
Pairing
Activation
1.
Press the Up or Down buttons to select “Pairing” and press the OK
button to enter:
2.
Press Up or Down to select a camera, and press OK to begin pairing.
Within 60 seconds, push the pairing button on the camera in for 2
seconds:
1.
Press the OK button to enter:
2.
3.
Press the Up or Down buttons to select a camera.
Press the Left or Right button to select On or Off (Off will disable the
camera view/recording/alarms on the system for that camera)
Press OK to confirm and exit.
4.
PIP Setting
Use this to set the resolution for display and for recording for each camera.
1. Press Up or Down to select a camera and press OK.
2. Use the Left and Right buttons to select Resolution or Quality.
3. Use Up or Down to adjust the selected setting.
4. Press OK to confirm.
5. Press Menu to exit.
3.
After successful pairing, the monitor displays the following information:
Alarm Setting
From the main menu, use the Left and Right buttons to select “Alarm” and press
OK. These settings are used to make an audible alarm sound when movement is
detected by Motion or PIR (depending on whether these are enabled in the record
settings).
If pairing fails, you will be notified on the monitor. Please try again.
Camera
Specifications
Imaging Sensor
Video Resolution
Power Supply
Viewing Angle
Consumption Current (Max.)
Waterproof Capacity
Night Vision Distance
Monitor
Dimensions (W x D x H)
Approx. Weight
LCD Screen Type
LCD Screen Resolution
SD Card
Hard Disk
Video Frame Rate (Max.)
Video Resolution
Video Format
Date Output
Power Supply
Consumption Current (Max.)
Dimensions (W x D x H)
Approx. Weight
Unobstructed Effective Range
Operating Temperature
Operating Humidity
Frequently Asked Questions
1DVRDIG502
1DVRDIG1502
1/5 inch colour CMOS
656 x 488
5V DC
50°
50°
400mA
600mA
IP54
IP66
5m (Max.)
15m (Max.)
132 x 64 x 57mm
164 x 81 x 172mm
(exc bracket)
(inc bracket)
300g
615g
7"TFT LCD
800 x 480
Supports up to 32GB
Supports up to 1TB
30fps
CIF/VGA
AVI
USB 2.0
5V DC
700mA
214 x 157 x 26 mm
510g
200m
-10°C - +50°C
15 - 85% RH
Warnings



“Why doesn’t the screen display an image from my camera after it is paired?”

Please ensure the camera channel is set to “Active”, see page 18.

“No Signal” could indicate that the camera is out of range.

“No Video” indicates that the monitor is detecting a signal from the
camera, but it is not strong enough to display an image.
“The screen looks scratched/scuffed, but it is brand new out of the box!”

There is a plastic film attached to the front of the screen to protect it
from damage in transit. This can be peeled off to reveal a pristine
screen.
“I can hear a rough sound from the microphone but nobody is around”

The microphone is very sensitive and often picks up atmospheric noise
like wind. Turn down the volume on the monitor.
“Motion detection keeps recording, but nobody is there”

Motion detection looks for movement from any source. Please ensure
there are no trees blowing in the wind or other movement.

High sensitivity levels can create ‘false positives’, try reducing the
sensitivity level.
“The PIR did not detect someone moving past”

The PIR has a maximum range of 5m on both the 5m and 15m night
vision camera models. In warm weather the range can be reduced.
FCC Information
This product should not be exposed to water unless otherwise stated.
Turn off the product if it is not in use.
Do not attempt to use any other power sources for this product other
than those provided.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following conditions:

This device may not cause harmful interference

This device must accept any interference received, including
interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement