HP Virtual Connect Flex-10 10Gb Ethernet Module for c

Add to my manuals
19 Pages

advertisement

HP Virtual Connect Flex-10 10Gb Ethernet Module for  c | Manualzz
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Overview
Simplify and make your data center change-ready. The HP Virtual Connect Flex-10 10Gb Ethernet Module for the c-Class
BladeSystem is the simplest, most flexible connection to your networks. The Virtual Connect Flex-10 Ethernet Module is a new class
of blade interconnect that simplifies server connections by cleanly separating the server enclosure from LAN, simplifies networks by
reducing cables without adding switches to manage, allows you to change servers in just minutes, not days, and tailors network
connections and speeds based on application needs. HP Flex-10 technology significantly reduces infrastructure costs by increasing
the number of NICs per connection without adding extra blade I/O modules, and reducing cabling uplinks to the data center
network. The HP Virtual Connect Flex-10 10Gb Ethernet Module for c-Class BladeSystem is an innovative, new class of integrated
interconnects from HP.
1.
2.
3.
4.
5.
Figure 1 Virtual Connect Ethernet Module Front Bezel
Module locator UUID
6.
Link indicator
Module status indicator
7.
Active mulitplexed port indicator
10Gb CX4 Backlit port number and status indicator
8.
Backlit port number and status indicator LED
10Gb CX4 link indicator
9.
Backlit port number and status indicator LED
Link indicator
10. Active mulitplexed port indicator
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 1
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Overview
What's New
Virtual Connect v3.15 highlights for the Virtual Connect Flex-10 Module
Supports new HP ProLiant BL2x220c G7 Server Blades, HP NC551m Dual Port FlexFabric 10Gb Converged Network
Adapter, HP NC552m 10Gb 2-port Flex-10 Ethernet Adapter; HP NC542m Dual Port Flex-10 10GbE BL-c Adapter
Virtual Connect v3.10 highlights for the Virtual Connect Flex-10 Module
Supports full TCP and iSCSI offload when connected to HP NC551i/m or NC553i FlexFabric adapters (Consult adapter
QuickSpecs for operating system and hypervisor support)
Removes VC Manager requirement for Primary/Secondary VC Interconnect modules placement in I/O bays 1 & 2
Supports for new HP ProLiant BL460c G7 Server Blade, HP NC553i 10Gb 2-port FlexFabric Converged Network
Adapter and HP NC522m Dual Port Flex-10 10GbE Multifunction BL-c Adapter
Displays Ethernet port statistics via the VCM CLI
Virtual Connect v3.01:
Support for new HP ProLiant BL465c G7 Server Blade, HP ProLiant BL685c G7 Server Blade, and HP NC550m 10Gb
2-port PCIe x8 Flex-10 Ethernet Adapter
IE8 support in IE7 compatibility mode
Expanded Direct Attach Cable support
At A Glance
Performance
16 x 10Gb downlinks to server NICs
2 x 10Gb cross connects for redundancy and stacking
1 x 10Gb copper uplinks CX-4 for stacking to Virtual Connect Modules or uplinking to data center switches
8 x 10Gb SR, LR, or LRM fiber and copper SFP+ uplinks
Supports up to 4 FlexNICs per 10Gb server connections.
Each FlexNIC is recognized by the server as a PCI-e physical function device with customizable speeds from 100Mb to 10Gb.
Line Rate, full-duplex 240Gbps bridging fabric
1.5 µs latency
MTU up to 9216 Bytes - Jumbo Frames
Configurable up to 8192 MAC addresses and 1000 IGMP groups
VLAN Tagging, Pass-Thru and Link Aggregation supported on all uplinks
Management
Virtual Connect Manager is included with every module
HTTP and a secure, scriptable CLI interface is ready out of the box. Easy setup and management via the Onboard
Administrator interface
SNMP v.1 and v.2, provide ease of administration and maintenance.
Role-based security for network and server administration with LDAP compatibility
Port Mirroring on any uplink provides network troubleshooting support with Network Analyzers
IGMP Snooping optimizes network traffic and reduces bandwidth for multicast applications such as streaming applications
Recognizes and directs Server-Side VLAN tags
Appears as a Pass-Thru device to the LAN Manager
Remotely update Virtual Connect firmware on multiple modules using Virtual Connect Support Utility 1.5.0 (Firmware update
is no longer accomplished via GUI or CLI with VC v3.01)
Virtual Connect Server Profiles
Create up to 4 individual FlexNICs with their own dedicated, customized bandwidth per 10Gb downlink connection.
Set FlexNIC speeds from 100Mb to 10Gb per connection
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 2
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Overview
Allows setup of server connectivity prior to server installation for easy deployment
Ability to move, add, or change server network connections on the fly
Once defined, LAN and SAN administrators don't have to be involved in server changes
Options
Stack multiple Virtual Connect Ethernet modules together in an enclosure to allow any server Ethernet port to connect to any
uplink
The Fibre Channel Virtual Connect Module provides a complete LAN and SAN Virtual Connect solution
HP CX4 Ethernet cables are available in .5m, 1m, 3m, and 15m lengths
Optional HP SFP+ SR, LR, and LRM modules and SFP+ Copper cables in 0.5m, 1m, 3m, and 7m lengths
Supports all 1Gb Server NICs including LOM and Mezzanine card options and the latest 10Gb KR NICs
Models
HP Virtual Connect Flex-10 10Gb Ethernet Module for the c-Class BladeSystem
HP Virtual Connect Flex-10 10Gb Enterprise Edition for BL-c7000, No Media, 1-Enclosure License including 1
year of 24x7 Technical Support and Updates
NOTE: Includes 2 x HP Virtual Connect Flex-10 10Gb Ethernet modules plus 1 x VCEM BL-c7000 enclosure
license. Customer will receive a printed license entitlement certificate and 2 Virtual Connect modules as a single
deliverable. The license entitlement certificate must be redeemed online or via fax to obtain the VCEM license
activation key.
DA - 13127
Worldwide — Version 13 — February 11, 2011
455880-B21
591973-B21
Page 3
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
Compatibility
HP ProLiant and Integrity NOTE: The HP BladeSystem c-Class Virtual Connect Firmware v3.X supports the following hardware.
Servers and Network
(HP Integrity BL8x0c i2 servers require VC FW 3.0 or higher) For the HP Virtual Connect Manager
options
Release Notes and Compatibility Matrix and the full listing of recommended and minimum firmware
versions, see the HP website.
Virtual Connect Modules
HP 1/10Gb Virtual Connect Ethernet Module
HP 1/10Gb-F Virtual Connect Ethernet Module
HP Virtual Connect FlexFabric 10Gb/24-port Module
HP 4Gb Virtual Connect Fibre Channel Module
HP Virtual Connect 8Gb 24-Port Fibre Channel Module
HP Virtual Connect 8Gb 20-Port Fibre Channel Module
Server blades and workstation blades
HP ProLiant BL2x220c G5 Server Blade or greater
HP ProLiant BL260c G5 Server Blade
HP ProLiant BL280c G6 Server Blade or greater
HP ProLiant BL460c Server Blade
HP ProLiant BL460c G5 Server Blade or greater
HP ProLiant BL465c Server Blade
HP ProLiant BL465c G5 Server Blade or greater
HP ProLiant BL480c Server Blade
HP ProLiant BL495c G5 Server Blade or greater
HP ProLiant BL680c G5 Server Blade or greater
HP ProLiant BL685c Server Blade
HP ProLiant BL685c G5 Server Blade or greater
HP Integrity BL860c Server Blade
HP Integrity BL860c i2 Server series
HP Integrity BL870c Server Blade
HP Integrity BL870c i2 Server series
HP Integrity BL890c i2 Server series
HP ProLiant xw460c Blade Workstation
HP ProLiant xw2x220c Blade Workstation
HP ProLiant WS460c G6 Workstation or greater
Enclosures
HP BladeSystem c-Class c7000 Enclosure with Onboard Administrator
HP BladeSystem c-Class c3000 Enclosure with Onboard Administrator
Integrated Network Interfaces and mezzanine cards
HP NC360m Dual Port 1GbE BL-c Adapter (supported by v1.21)
HP NC364m Quad Port 1GbE BL-c Adapter (supported by v1.21)
HP NC325m PCI Express Quad Port 1Gb server adapter
HP NC326i Integrated Dual Port PCI Express Gigabit Server Adapter
HP NC326m PCI Express Dual Port Multifunction Gigabit Server Adapter
HP NC360m Dual Port 1GbE BL-c Adapter
HP NC364m Quad Port 1GbE BL-c Adapter
HP NC370i Dual Port Multifunction Gigabit Network Adapter
HP NC373i Dual Port Multifunction Gigabit Network Adapter
HP NC373m Dual Port Multifunction Gigabit Network Adapter
HP NC382i Integrated Dual Port PCI Express Gigabit Server Adapter
HP NC382m Integrated Dual Port PCI Express Gigabit Server Adapter
HP NC532i Dual Port Flex-10 10GbE Multifunction BL-c Adapter
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 4
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
QuickSpecs
Supported Products
HP NC532m Dual Port Flex-10 10GbE Multifunction BL-c Adapter
HP NC542m Dual Port Flex-10 10GbE BL-c Adapter
HP NC550m 10Gb 2-port PCIe x8 Flex-10 Ethernet Adapter
HP NC522m Dual Port Flex-10 10GbE Multifunction BL-c Adapter
HP NC551i Dual Port FlexFabric 10Gb Converged Network Adapter
HP NC551m Dual Port FlexFabric 10Gb Converged Network Adapter
HP NC553i 10Gb 2-port FlexFabric Converged Network Adapter
HP NC553m 10Gb 2-port FlexFabric Converged Network Adapter
NOTE: For optimal operation of HP Virtual Connect Manager, use the following recommended firmware
version for the Onboard Administrator and iLO.
NOTE: Some of the servers and/or options listed above may be discontinued.
iLO
Virtual Connect Firmware version Onboard Administrator
VC 3.15
For c7000 Enclosure,
HP ProLiant iLO2: Recommended
recommended version 3.11 or
version 2.0 or higher
higher
HP ProLiant iLO3: Recommended
For c3000 Enclosure,
version 1.10 or higher
recommended version 3.11 or
HP Integrity: Recommended
higher
version T.02.17 or higher
HP Integrity i2 Series:
Recommended version K15.05 or
higher
NOTE: For the HP Virtual Connect Manager Release Notes and Compatibility Matrix and the full listing
of recommended and minimum firmware versions, see the HP website.
NOTE: HP Integrity BL8x0c i2 Server Blades require OA FW 3.0 or later.
HP ProLiant and Integrity
The HP BladeSystem c3000 and c7000 Enclosure has been designed up front with the Virtual
BL c-Class
Connect Architecture in mind incorporating the HP Onboard Administrator, ILO Management,
Server Blade Enclosures
and HP Management tools inside the Virtual Connect framework.
Virtual Connect requires the following minimum firmware levels:
Supported Configurations
1. Upper Fan System
HP BladeSystem c7000 Enclosure - Rear View
5. Interconnect Bays 7 / 8
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 5
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
2. Interconnect Bays 1 /2
3. Interconnect Bays 3 / 4
4. Interconnect Bays 5 / 6
6. On Board Administrator
7. Lower Fan System
8. Rear Redundant Power Complex
HP BladeSystem c3000 Enclosure - Front View
1. Device Bays 1 thru 8
4. Insight Display
2. Enclosure DVD Drive
5. Active Onboard Administrator
3. Standby Onboard Administrator (reserved for Future)
1.
2.
3.
4.
HP BladeSystem c3000 Enclosure - Rear View
Local KVM interface (reserved for future)
7. iLO/Onboard Administrator Port
Interconnect Bay 1
8. iLO/Onboard Administrator Port 2 (reserved for future)
Active Cool Fans
9. Power Supplies
Interconnect Bay 2
10. Interconnect Bay 4
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 6
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
5. Enclosure Up-link and Service Port
6. Enclosure Down-link
11. Interconnect Bay 3
Mezzanines
c-7000 Port Mapping
Port mapping differs slightly between full height and half height server blades due to the support for
additional Mezzanine cards on the full height version.
HP has simplified the processes of mapping Mezzanine ports to switch ports by providing intelligent
management tools via the Onboard Administrator and HP Insight Manager Software. The Onboard
Administrator Guide, Enclosure Setup and Installation Guide provides detailed information on port
mapping.
Half Height Server Blade
c-3000 Port Mapping
Full Height Sever Blade
Port mapping differs slightly between full height and half height server blades due to the support for
additional Mezzanine cards on the full height version.
HP has simplified the processes of mapping Mezzanine ports to switch ports by providing intelligent
management tools via the Onboard Administrator and HP Insight Manager Software. The Onboard
Administrator Guide, Enclosure Setup and Installation Guide provides detailed information on port
mapping.
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 7
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
Half Height Server Blade
Full Height Sever Blade
The following are supported configurations for the Virtual Connect Flex-10 Ethernet Module. Please note that other interconnect
options can be installed in the enclosure, but they do not inherit the benefits of Virtual Connect. Switches and Pass-Thru modules will
operate per their default configurations. Any moves, adds, or changes to servers which are connected to non-Virtual Connect
modules will require reconfiguration on the LAN and/or SAN. The Virtual Connect Manager will only manage Virtual Connect
Modules.
HP BladeSystem c7000 Enclosure
NOTE: The following tables show a number of typical, supported configurations for an HP BladeSystem c7000 Enclosure.
[Bay 1] VC-Enet
[Bay 3] Other/empty
[Bay 5] Other/empty
[Bay 7] Other/empty
[Bay 2] Empty
[Bay 4] Other/empty
[Bay 6] Other/empty
[Bay 8] Other/empty
[Bay 1] VC-Enet
[Bay 3] Other/empty
[Bay 5] Other/empty
[Bay 7] Other/empty
[Bay 2] VC-Enet
[Bay 4] Other/empty
[Bay 6] Other/empty
[Bay 8] Other/empty
[Bay 1] VC-Enet
[Bay 3] VC-Enet
[Bay 5] Other/empty
[Bay 7] Other/empty
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 6] Other/empty
[Bay 8] Other/empty
[Bay 1] VC-Enet
[Bay 3] Other/empty
[Bay 5] VC-Enet
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] Other/empty
[Bay 6] VC-Enet
[Bay 8] Empty
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 8
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
[Bay 1] VC-Enet
[Bay 3] VC-Enet
[Bay 5] VC-Enet
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 6] VC-Enet
[Bay 8] Empty
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 5] Other/empty
[Bay 7] Other/empty
[Bay 2] Empty
[Bay 4] Empty
[Bay 6] Other/empty
[Bay 8] Other/empty
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 5] Other/empty
[Bay 7] Other/empty
[Bay 2] VC-Enet
[Bay 4] VC-FC
[Bay 6] Other/empty
[Bay 8] Other/empty
[Bay 1] VC-Enet
[Bay 3] VC-Enet
[Bay 5] VC-FC
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 6] VC-FC
[Bay 8] Empty
[Bay 1] VC-Enet*
[Bay 3] VC-Enet
[Bay 5] VC-FC
[Bay 7] VC-FC
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 6] VC-FC
[Bay 8] VC-FC
* This configuration is only applicable for enclosures with full-height servers.
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 5] VC-Enet
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] VC-FC
[Bay 6] VC-Enet
[Bay 8] Empty
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 5] VC-Enet
[Bay 7] VC-Enet
[Bay 2] VC-Enet
[Bay 4] VC-FC
[Bay 6] VC-Enet
[Bay 8] VC-Enet
[Bay 1] VC-Enet
[Bay 3] Other/empty
[Bay 5] VC-FC
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] Other/empty
[Bay 6] VC-FC
[Bay 8] Empty
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 9
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 5] VC-FC
[Bay 7] Empty
[Bay 2] VC-Enet
[Bay 4] VC-FC
[Bay 6] VC-FC
[Bay 8] Empty
[Bay 1] VC-Enet
[Bay 3] VC-Enet
[Bay 5] VC-Enet
[Bay 7] VC-Enet
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 6] VC-Enet
[Bay 8] VC-Enet
NOTE: When using VC Flex-10 Modules with Flex-10 NICs on server blades, only VC Ethernet modules
may be used for Ethernet connections in the same enclosure.
HP BladeSystem c3000 Enclosure
NOTE: The following tables show a number of typical, supported configurations for an HP BladeSystem c3000 Enclosure.
[Bay 1] VC-Enet
[Bay 3] Empty
[Bay 2] VC-Enet
[Bay 4] Empty
[Bay 1] VC-Enet
[Bay 3] Empty
[Bay 2] Empty
[Bay 4] Empty
[Bay 1] VC-Enet
[Bay 3] VC-Enet
[Bay 2] VC-Enet
[Bay 4] VC-Enet
[Bay 1] VC-Enet
[Bay 3] VC-FC
[Bay 2] VC-Enet
[Bay 4] VC-FC
NOTE: When using VC Flex-10 Modules with Flex-10 NICs on server blades, only VC Ethernet modules
may be used for Ethernet connections in the same enclosure.
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 10
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Supported Products
Required Cabling
10GBASE-CX4
Twinax CX4 (0.5 to 15m)
NOTE: For available cables; please see the "Options" section below of this QuickSpecs.
Maximum Distances
Multimode OM1
62.5/125 micron
2 - 26m/33m*
Multimode OM2
50/125 micron
2 - 82m
Multimode OM3
50/125 micron
2 - 300m
Singlemode
9 micron
SR
LR
2 -10km
LRM
0.5 - 220m
0.5 - 220m
0.5 - 220m
* 26m at 160MHz and 33m at 200MHz.
NOTE: For additional information on 10Gb cable specifications go to: http://www.hewlett-packard.com/rnd/pdfs/10gig_cabling_
technical_brief.pdf
Stacking Configuration
Stacking links are used to interconnect Virtual Connect Ethernet Modules when using more than one
enclosure or when using more than two Virtual Connect Ethernet Modules in a single enclosure.
All Virtual Connect Modules within the VC Domain must be interconnected. Any combination of 1Gb
and 10Gb cables can be used to interconnect the Virtual Connect Modules; however the following
provides recommended configurations (note that a built-in 10Gb link is provided between modules in
horizontally adjacent bays). Supported cable lengths on 10Gb uplinks are 3 to 15 meters and supported
10Gb stacking links (connecting between two HP Virtual Connect Ethernet Modules) are 0.5 to 7 meters.
Interconnecting the modules allows all Ethernet NICs on all server blades in the Virtual Connect domain
to have access to any Virtual Connect uplink port. By using these module-to-module links, a single pair
of uplinks can be used as the data center network connections for the entire Virtual Connect domain,
and allows any server blade to be connected to any Ethernet network.
NOTE: Supported module-to-module and multi-enclosure stacking configurations may be found in the
HP Virtual Connect for c-Class BladeSystem Setup and Installation Guide which can be downloaded at
the following address: HP Virtual Connect for c-Class BladeSystem and Installation Guide
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 11
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Service and Support, HP Care Pack and Warranty Information
Service and Support
This product is covered by a global limited warranty and supported by HP Services and a worldwide
network of HP Authorized Channel Partners. Hardware diagnostic support and repair is available for
three years from date of purchase. Support for software and initial setup is available for 90 days from
date of purchase. Additional support may be covered under the warranty or available for an additional
fee. Enhancements to warranty services are available through HP Care Pack services or customized
service agreements.
NOTE: Server Blade Interconnect Limited Warranty includes 1 year Parts, 1 year Labor, 1-year on-site
support. Additional information regarding worldwide limited warranty and technical support is available
at: http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
HP services provide total care and support expertise with committed response designed to meet your IT
and business needs.
To fully capitalize on your HP BladeSystem servers' capabilities requires a service partner who thoroughly
understands your server technology and systems environment. HP Services, an industry leader in
provision of multi vender support solutions provides a range of support services designed to meet the
varying needs of business. Whether an SMB or large global corporation HP has a HP BladeSystem server
support offer to help you speedily deploy and maximize system uptime.
Recommended Service - Simplify ProLiant solution implementation, maintenance and management.
Support Service - 4-Hour Response Coverage, 3-Year, 24 x 7, Same Business Day
Deployment Service - BladeSystem c3000/c7000 Infrastructure (ICE + OS) Installation &
Startup - Provides for the installation and startup of a BladeSystem c3000/c7000 Infrastructure in
a single blade enclosure including hardware and software (HP SIM, RDP, RDP deployment of OS,
PMP and VPM)
Enhanced Service - Optimize service level to increase IT performance and availability
Enhanced Network Installation & Startup for BladeSystem Switches - Provide for the
configuration and testing of BladeSystem Ethernet interconnect switches to facilitate proper
implementation of network protocols and access to advanced features. (This service has been
updated to include coverage for the VC FlexFabric features.)
Support Service- 3-Year, either 6 hour or 24 hour call to repair HP Hardware Support Onsite 6Hour or 24-hour Call-to-Repair Service provides you with a team of support specialists who will
quickly begin troubleshooting your system to ensure the hardware is operational within a
maximum of 6 hours or 24 hours from your initial service request
Support Service - 3-Year, 24x7 Same-Business-Day, On-site. 4-Hour response coverage,
including holidays Hardware Onsite Service delivers round the clock, fast reliable 4 hour
response-Get product expertise from HP for fast and accurate problem resolution with integrated
high quality remote monitoring and problem diagnosis, maintaining predictable service levels
reducing unplanned downtime
Proactive Select - A flexible way to purchase HP best-in-class consultancy and services. You can
buy Proactive Select Service Credits when you purchase your hardware then use the credits over
the next 12 months, or 3-5 years.
Installation & Start-Up service for HP BladeSystem Infrastructure plus HP BladeSystem Enhanced Network
Installation and Start-UP as per the Customer Description and/or Data Sheet. To be delivered on a
scheduled basis 8am-5pm, M-F, excluding HP holidays.
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 12
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Service and Support, HP Care Pack and Warranty Information
For a complete listing of service offerings and information visit:
http://www.hp.com/services/bladesystemservices
http://www.hp.com/go/proliant/carepack
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 13
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Related Options
Cabling and Transceiver HP .5m 10GbE CX4 Cable
Options
HP 1m 10GbE CX4 Cable
HP 3m 10GbE CX4 Cable
HP 15m 10GbE CX4 Cable
HP 0.5m SFP+ 10GbE Copper Cable
HP 1m SFP+ 10GbE Copper Cable
HP 3m SFP+ 10GbE Copper Cable
HP 5m SFP+ 10GbE Copper Cable
HP 7m SFP+ 10GbE Copper Cable
HP C-Series 10GB Copper Cable, 3m
NOTE: Equivalent to Cisco 3-m 10G SFP+Copper Twinax Cable (PN SFP-H10GBCU3M).
HP C-Series 10GB Copper Cable, 5m
NOTE: Equivalent to Cisco 5-m 10G SFP+Copper Twinax Cable (PN SFP-H10GBCU5M).
HP 1m B-series Active Copper SFP+ Cable
NOTE: Equivalent to Brocade 10Gbps Direct Attached SFP+Copper Cable - 1m (PN
XBR-TWX-0101).
HP 3m B-series Active Copper SFP+ Cable
NOTE: Equivalent to Brocade 10Gbps Direct Attached SFP+Copper Cable -3m (PN
XBR-TWX-0301).
HP 5m B-series Active Copper SFP+ Cable
NOTE: Equivalent to Brocade 10Gbps Direct Attached SFP+Copper Cable-5m (PN
XBR-TWX-0501).
Ethernet Optical Transceivers
HP BladeSystem 10Gb SR SFP+
HP BladeSystem 10Gb LR SFP+
HP BladeSystem 10Gb LRM SFP+
HP BladeSystem 1Gb SX SFP Opt Kit
HP BladeSystem 1Gb RJ-45 SFP Opt Kit
HP 2 m LC-LC Multi-Mode OM2 Fiber Optic Cable
HP 5 m LC-LC Multi-Mode OM2 Fiber Optic Cable
HP 15 m LC-LC Multi-Mode OM2 Fiber Optic Cable
HP 30 m LC-LC Multi-Mode OM2 Fiber Optic Cable
HP 50 m LC-LC Multi-Mode OM2 Fiber Optic Cable
HP .5 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 1 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 2 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 5 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 15 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 30 m LC-LC Multi-Mode OM3 Fiber Optic Cable
HP 50 m LC-LC Multi-Mode OM3 Fiber Optic Cable
NOTE: In addition to the supported HP and non-HP Copper Twinax and Active
DA - 13127
Worldwide — Version 13 — February 11, 2011
444477-B21
444477-B22
444477-B23
444477-B27
487649-B21
487652-B21
487655-B21
537963-B21
487658-B21
AP784A
AP785A
AP818A
AP819A
AP820A
455883-B21
455886-B21
455889-B21
453151-B21
453154-B21
221692-B21
221692-B22
221692-B23
221692-B26
221692-B27
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
Page 14
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Related Options
Copper SFP+ cables above, Virtual Connect provides "allowed" connections using
third party cables that meet the following criteria: connector=copper pigtail;
transceiver code=active cable or passive cable; speed equal or less than 10Gb;
length between 1m and 7m, inclusive. All "allowed" DACs are connected and logged.
Prior to requesting support from HP, a DAC from the supported list above must be
used to verify a cable issue is not involved.
Service and Support
Offerings
NOTE: The HP Care Pack service part numbers below for ProLiant BL c-Class server
blades, cover the server blade and all HP branded hardware options qualified for the
server, purchased at the same time or afterwards, internal to the server.
Hardware Services On-site Service
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
NOTE: HP Care Pack services for the c7000 and c3000 Enclosures cover the
enclosure, power supplies and fans. HP qualified rack options are covered by these
services when installed within the same rack. HP supported c-Class enclosure devices
including pass thru, Ethernet interconnect and virtual connect modules are also
covered by the c7000 and c3000 enclosures Care Pack services.
NOTE: SAN/Fabric switches for the HP c-Class BladeSystem are not covered under
the c7000 and c3000 enclosures Care Packs, SAN/Fabric switches carry separate
Care Packs. SAN/Fabric Switch Care Pack service level support should always be
uplifted to match existing storage or server service level.
Hardware Services On-site Service
Next Business Day On-site Service, 5-Day x 9-Hour Coverage, 3 Years, Electronic
NOTE: Uplifts the Ethernet devices to the same level of service as the c-class
enclosure.
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
Installation & Start-up Services
Hp BladeSystem c-Class Infrastructure Installation and Startup Service, Electronic
HP BladeSystem Enhanced Network Installation and Startup Service, Electronic
ProLiant BL c-Class Blade Server Hardware Installation, Electronic
ProLiant BL c-Class Enclosure and Server Blade Hardware Installation, Electronic
NOTE: For additional information; please visit:
http://www.hp.com/services/bladesystemservices
DA - 13127
Worldwide — Version 13 — February 11, 2011
UE458E
UE459E
UE460E
UE477E
UE478E
UE479E
UE480E
UE602E
UE603E
UE493E
UE494E
Page 15
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Technical Specifications
Shipping Dimensions
Shipping Weight
Product Specifications
Hardware
Length
Width
Height
13.88 in (352.55 mm)
10.63 in (270.00 mm)
4.75 in (120.65 mm)
4.4 lbs (2.0 kg)
Performance
Line Rate, full-duplex 240Gbps bridging fabric
Non-blocking architecture
Maximum transmission unit (MTU) of up to 9216 bytes (jumbo frames)
Connectors and Cabling 16 x 10Gb downlinks midplane
2 x 10Gb cross connect
1 x 10Gb copper uplinks CX-4
8 x 10Gb SR, LR, or LRM fiber uplinks SFP+
1 management USB port
1 internal interface to c-Class Onboard Administrator Module
Indicators
Recessed Momentary Reset Switch
Momentary Next/Step Switch
Backlit port number and status indicator LED, one per bulkhead port,
blue/amber/green
Module status indicator, amber/green
Module locator (UID), blue
Link indicator, one per CX4-port, green
Link indicator, one per SFP+-port, green/amber
USB port (covered)
Active multiplexed port indicator, green
Dimensions
Length
10.5 in (267.7 mm)
Width
7.5 in (92.79 mm)
Height
1.1 in (27.94 mm)
Weight
1.27Kg (2.8 Lbs)
Environmental Ranges
Temperature Range
Specification
10C to 35C (50F to 95F)
Range*
Temperature Range
Operating
10C to 35C (50F to 95F)
Shipping
Shipping -40C to 60C (-40F to 140F)
Storage
-20°C to 60°C (-4F to 140°F)
Maximum wet bulb
30C (80F)
temperature
Relative Humidity
(noncondensing)**
Operating
10% to 90%
Shipping
10% to 90%
Storage
10% to 95%
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 16
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Technical Specifications
* All temperature ratings shown are for sea level. An altitude derating of 1°C per 304.8 m (1.8°F per
1,000 ft) to 3048 m (10,000 ft) is applicable. No direct sunlight allowed. Upper operating limit is
3,048m (10,000 ft) or 70 Kpa/10.1 psia. Upper non-operating limit is 9,144 m (30,000 ft) or 30.3
KPa/4.4 psia.
** Storage maximum humidity of 95% is based on a maximum temperature of 45°C (113°F). Altitude
maximum for storage corresponds to a pressure minimum of 70 KPa.
12V @ 8.75A (105 W)
Power Specification
Product Specifications
Software
Security Features
Trunking and Failover
Features
HTTPS (HTTP exchanged over an SSL-encrypted session) is required for
access to the Virtual Connect Manager.
Access to the Virtual Connect Manager is via the system Onboard
Administrator
Each user account can be configured for a combination of four access
privileges to control and/or view elements in the Virtual Connect
Manager.
User verification by account name and password (Case Sensitive)
LDAP Authentication services provide role based security via an LDAP
SSL Directory Server connection.
Private VLAN's for secure connectivity between servers within a domain
Shared Uplink Sets using Link Aggregation Control Protocol (LACP) allows
the creation of Ethernet channeling with upstream switches that conform to
IEEE 802.3ad. Ports can alternatively be configured for failover only.
External ports within a Port Set can be on the same VC Ethernet module or
on multiple VC modules within the VC domain.
In the event of an uplink failure to a data center switch, the next highest
performance uplink connection or aggregation will become active.
Fast MAC Cache failover enables rapid recovery of network connections
when a standby module becomes active.
Smart Link network senses a failed upstream switch connection and allows
teamed NICs to properly failover.
VLAN Features
Configure uplink speeds to Auto, 1Gb,or10Gb on the associated uplinks
802.1Q VLAN supported on uplinks.
Uplink ports can be configured for VLAN tagging at egress or pass-thru of
tagged VLAN packets from Server ports.
Management Features
Native VLAN support for untagged packets on a shared uplink set. Packets
can be targeted to a specific server ports.
Simple and intuitive Graphical User Interface (GUI) for defining, configuring,
and managing all elements of the Virtual Connect Domain.
Setup Wizards for initial domain installation and configuration and network
configuration.
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 17
QuickSpecs
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
Technical Specifications
Comprehensive administration, definition, and management of Ethernet
Network, Shared Uplink Set, and Server Profiles
Embedded SNMP v1, v2 and SMI-S agents allow Network Management
applications to query Virtual Connect for statistics and trap information.
A robust, scriptable and secure Command Line Interface simplifies
management and enables macros to control common Virtual Connect tasks
Any uplink port can be used as a dedicated mirrored port for traffic analysis
and troubleshooting by a Network Analyzer or Sniffer.
Domain Management of user accounts, enclosure, Virtual Connect domain
settings, and firmware updates
The location and status of Virtual Connect Modules in the HP c-Class
Enclosure and Onboard Administrator can be viewed from the Hardware
Status page. Including at-a-glance detailed information of the hardware
elements via mouse-over pop-up windows.
MAC Address Administration allows local administration of predefined or
user-defined MAC address ranges.
VC manager runs as a high-availability pair when an HP 1/10Gb VC-Enet
Module is installed in adjacent bays. All configuration data is stored in flash
memory and checkpointed to the standby module. Configurations can also
be backed up to a workstation via the GUI.
Management and
Standards Support
Standards
802.1AB LLDP
802.1Q (VLAN, 1024 maximum, includes Native VLAN support and server
side VLAN tag mapping)
IEEE 802.2 LLC
802.3ad Link Aggregation
IEEE 802.3ae 10Gb Fiber Ethernet
IEEE 802.3ak 10Gb CX-4 Ethernet
IEEE 802.3aq 10Gb LRM Ethernet
SNMP v.1, v.2
IGMP v1, v2
Safety and
Compliance
Safety Certifications
UL/CUL Recognition to UL/CSA 60950-1
TUV to EN 60950-1
CB report and certificate to IEC 60950-1 with all country deviations
CE Marking
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 18
HP Virtual Connect Flex-10 10Gb Ethernet Module for
c-Class BladeSystem
QuickSpecs
Technical Specifications
Electromagnetic
Emissions Certifications
FCC Part 15 Class A
FCC Part 15 Class A
EN 55022 Class A (CISPR22 Class A)
VCCI Class A
AS/NZS 3548 Class A or AS/NZS CISPR22 Class A
MIC Class A
CE Marking
Environment-friendly
Products and Approach
End-of-life Management
and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to:
http://www.hp.com/go/green. To recycle your product, please go to:
http://www.hp.com/go/green or contact your nearest HP sales office.
Products returned to HP will be recycled, recovered or disposed of in a
responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green. These instructions may
be used by recyclers and other WEEE treatment facilities as well as HP OEM
customers who integrate and re-sell HP equipment.
© Copyright 2011 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
DA - 13127
Worldwide — Version 13 — February 11, 2011
Page 19

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement