A-20-K/-S A-30-K/-S A-10-K/-S
A30_SYXE8_cover_anki.fm
1 ページ
2012年2月21日 火曜日 午後1時42分
Operating Instructions | Mode d’emploi | Bedienungsanleitung |
Istruzioni per I’uso | Handleiding | Manual de instrucciones |
Инструкции по эксплуатации
AME06
30
20
10
AIntegrated Amplifier | Amplificateur Intégré |
Eingebauter Verstärker | Amplificatore Integrato |
Geïntegreerde versterker | Amplificador integrado |
A-
-K/-S
-K/-S
-K/-S
A30_SYXE8.book
2 ページ
2012年2月16日 木曜日 午前8時58分
WARNING
IMPORTANT
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
D3-4-2-1-1_A1_En
European model only
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
Symbol examples
for batteries
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
Pb
K058a_A1_En
D3-4-2-1-3_A1_En
WARNING
Before plugging in for the first time, read the following
section carefully.
The voltage of the available power supply differs
according to country or region. Be sure that the
power supply voltage of the area where this unit
will be used meets the required voltage (e.g., 230 V
or 120 V) written on the rear panel.
D3-4-2-1-4*_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space
around the unit for ventilation to improve heat radiation
(at least 30 cm at top, 10 cm at rear, and 10 cm at each
side).
WARNING
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product,
and to protect it from overheating. To prevent fire
hazard, the openings should never be blocked or
covered with items (such as newspapers, table-cloths,
curtains) or by operating the equipment on thick carpet
or a bed.
D3-4-2-1-7b*_A1_En
A30_SYXE8.book
3 ページ
2012年2月16日 木曜日 午前8時58分
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
locations exposed to high humidity or direct sunlight (or
strong artificial light)
This product is for general household purposes. Any
failure due to use for other than household purposes
(such as long-term use for business purposes in a
restaurant or use in a car or ship) and which requires
repair will be charged for even during the warranty
period.
K041_A1_En
D3-4-2-1-7c*_A1_En
If the AC plug of this unit does not match the AC
outlet you want to use, the plug must be removed
and appropriate one fitted. Replacement and
mounting of an AC plug on the power supply cord of
this unit should be performed only by qualified
service personnel. If connected to an AC outlet, the
cut-off plug can cause severe electrical shock. Make
sure it is properly disposed of after removal.
The equipment should be disconnected by removing
the mains plug from the wall socket when left unused
for a long period of time (for example, when on
vacation).
D3-4-2-2-1a_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S002*_A1_En
CAUTION
The /I STANDBY/ON switch on this unit will not
completely shut off all power from the AC outlet.
Since the power cord serves as the main disconnect
device for the unit, you will need to unplug it from the
AC outlet to shut down all power. Therefore, make
sure the unit has been installed so that the power
cord can be easily unplugged from the AC outlet in
case of an accident. To avoid fire hazard, the power
cord should also be unplugged from the AC outlet
when left unused for a long period of time (for
example, when on vacation).
D3-4-2-2-2a*_A1_En
Thank you for buying this Pioneer
product.
Please read through these operating instructions so that
you will know how to operate your model properly. After
you have finished reading the instructions, put them in a
safe place for future reference.
Contents
01 Before you start
What’s in the box. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Loading the batteries in the remote control
(Except A-10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Using the remote control. . . . . . . . . . . . . . . . . . . . .4
Installing the amplifier . . . . . . . . . . . . . . . . . . . . . . 4
02 Connecting up
Making cable connections. . . . . . . . . . . . . . . . . . . 5
About “Bi-wiring” . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connecting speaker cables . . . . . . . . . . . . . . . . . . 6
Connecting audio cables . . . . . . . . . . . . . . . . . . . . 6
Using centralized control with other Pioneer
components (Except A-10) . . . . . . . . . . . . . . . . . . . 6
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
03 Controls and displays
(A-30 only)
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal
heatsink may become hot when
operating this product continuously.
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote control (Except A-10) . . . . . . . . . . . . . . . . 9
04 Operation
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Set the power to Standby. . . . . . . . . . . . . . . . . . . .10
When using the unit as a power amplifier
(A-30 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Making an audio recording . . . . . . . . . . . . . . . . . 11
To set for automatic standby status
(Auto Power Down) . . . . . . . . . . . . . . . . . . . . . . . 11
Restoring all the settings to the factory default
settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
05 Additional information
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning the unit . . . . . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3
A30_SYXE8.book
01
4 ページ
2012年2月16日 木曜日 午前8時58分
Before you start
Chapter 1:
Before you start
2 Insert the new batteries, matching the
polarities as indicated inside the case.
What’s in the box
Please confirm that the following accessories are in the
box when you open it.
• Remote control (Except A-10)
• AAA/IEC R03 dry cell batteries x2 (Except A-10)
• Power cord
• Warranty card
• Operating instructions (This document)
A-30
A-20
Note
• Illustrations featured in the Operating Instructions
may have been modified or simplified for ease of
explanation, and may therefore differ from the
actual product appearance.
• The illustrations used here are mainly of the A-30.
3
Using the remote control
Close the rear lid.
A-30
• Do not use any batteries other than the ones
specified. Also, do not use a new battery together
with an old one.
• When loading the batteries into the remote control,
set them in the proper direction, as indicated by the
polarity marks ( and ).
• Do not heat batteries, disassemble them, or throw
them into flames or water.
• Batteries may have different voltages, even if they
are the same size and shape. Do not use different
types of batteries together.
• To prevent leakage of battery fluid, remove the
batteries if you do not plan to use the remote
control for a long period of time (1 month or more).
If the fluid should leak, wipe it carefully off the
inside of the case, then insert new batteries. If a
battery should leak and the fluid should get on your
skin, flush it off with large quantities of water.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public institution’s rules that apply in your country/
area.
A-20
The remote has a range of about 7 m at an angle of about
30º from the remote sensor.
Loading the batteries in the remote
control (Except A-10)
1
Open the rear lid.
A-30
30 °
30 °
A-20
The batteries included with the unit have been provided
to allow you check product operation and may not last
long. We recommend using alkaline batteries that have
a longer life.
WARNING
• Do not use or store batteries in direct sunlight or
other excessively hot place, such as inside a car or
near a heater. This can cause batteries to leak,
overheat, explode or catch fire. It can also reduce
the life or performance of batteries.
Caution
Incorrect use of batteries may result in such hazards as
leakage and bursting. Observe the following
precautions:
• When inserting the batteries, make sure not to
damage the springs on the battery’s  terminals.
4
En
7m
Keep in mind the following when using the remote
control:
• Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
• Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
• Remote controllers for different devices can
interfere with each other. Avoid using remotes for
other equipment located close to this unit.
• Replace the batteries when you notice a fall off in
the operating range of the remote.
Installing the amplifier
When installing this unit, make sure to put it on a level
and stable surface.
• Don’t install it on the following places:
– on a color TV (the screen may distort)
– near a cassette deck (or close to a device that
gives off a magnetic field). This may interfere with
the sound.
– in direct sunlight
– in damp or wet areas
– in extremely hot or cold areas
– in places where there is vibration or other
movement
– in places that are very dusty
– in places that have hot fumes or oils (such as a
kitchen)
• Do not mount the unit on a sofa or other object or
material with absorbent qualities, since sound
quality may be adversely affected.
A30_SYXE8.book
5 ページ
2012年2月16日 木曜日 午前8時58分
Connecting up
02
Caution
Connecting up
Caution
• Before making or changing the connections, switch off the power and disconnect the power cord from the AC
outlet.
• Connect the power cord after all the connections between devices have been completed.
Speaker system B
Left
Right
Network audio player
LOW
LOW
A-30’s rear
panel
Deutsch
PRE OUT jacks on preamplifier or AV amplifier
SACD/CD player
Speaker system
Speaker system
Left
Right
Remove the shorting
bar between the +
and – terminals.
HIGH
HIGH
Français
Making cable connections
• The SIGNAL GND terminal is provided to reduce
noise when connecting the unit to components
such as an analog turntable.
• Do not connect the PHONO (MM) terminals to any
component other than a turntable; also, do not
connect to a turntable equipped with built-in
equalizer. An excessively high sound output may be
produced, resulting in damage to your speakers or
other devices.
• The unit’s PHONO (MM) terminals are designed to
be used with turntables equipped with MM
(moving-magnet) type cartridges. Turntables
equipped with MC (moving-coil) cartridges cannot
be used.
• Make sure not to bend the cables over the top of
this unit (as shown in the illustration). If this
happens, the magnetic field produced by the
transformers in this unit may cause a humming
noise from the speakers.
• During playback, be sure that both the SPEAKERS
A button and SPEAKERS B button are set to ON
(page 7).
English
Chapter 2:
PRE OUT
R
R
L
L
R
Italiano
A-30 only
L
R
L
A-30’s rear panel
R
L
L
R
• The unit’s POWER AMP DIRECT terminals should
never be connected to any other component’s
connectors except PRE-AMP OUT.
• If your turntable has a grounding wire, secure it to
the ground terminal on this amplifier.
R
Note
R
L
R
L
R
L
R
L
Power cord
(included)
L
R
AUDIO
OUTPUT
R
L
OUTPUT
L
R
R
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
PLAY REC
L
L
L
R
R
R
About “Bi-wiring”
MENU



Turntable
Tuner
iPod dock, etc
CD recorder or
tape deck
Left
Right
Speaker system A
This unit can be used with speakers that support biwiring. Be sure to connect the high-frequency and
low-frequency connections correctly.
Русский
L
Español
L
R
• When connecting a tape cassette deck, playback
noise may be heard, depending on the installation
location. This noise is caused by leakage flux from
the amplifier’s transformer. In this event, change
the installation location, or move the deck farther
from the amplifier.
• iPod is a trademark of Apple Inc., registered in the
U.S. and other countries.
Caution
• When using bi-wiring to connect speakers, avoid
adverse affects on the amplifier by being sure to
remove the HIGH and LOW short bars provided
with the speakers. For detailed information, consult
the instructions provided with the speakers.
• When using speakers with removable network
circuits, note that if the network is removed, no
effect will be produced and damage may be caused
to the speaker.
• Another method of connection is to connect the
SPEAKERS A terminals to HIGH and the
SPEAKERS B terminals to LOW (reverse that shown
in the illustration).
Nederlands
L
5
En
02_connecting_up.fm
02
6 ページ
2012年6月21日 木曜日 午後2時1分
Connecting up
Connecting speaker cables
Connecting audio cables
1
Connect the white plug to the left (L) jack, and the red
plug to the right (R) jack. Be sure to insert the plugs fully
into the jacks.
Twist the cable cores.
2 Loosen the nut on the SPEAKERS
terminal, and insert the speaker cable into
the exposed hole in the terminal shaft.
3
Left (white)
Retighten the terminal nut.
Right (red)
1
2
Using centralized control with other
Pioneer components (Except A-10)
Plugging in
Multiple Pioneer components equipped with CONTROL
IN/OUT jacks can be connected to the A-30/A-20 unit,
allowing centralized control of the components via the
remote sensor on the A-30/A-20. This also allows remote
control of components not equipped with a remote
sensor, or installed in places where the component’s
remote sensor cannot be accessed.
Important
• When going on a trip or otherwise not using the
unit for an extended period, always disconnect the
power cord from its outlet. Note that various
internal settings will not be lost even if the power
cord is disconnected from its outlet for an extended
time.
• If it is necessary to detach the power cord, first be
sure to press the /I STANDBY/ON button on the
front panel of the unit so the A-30/A-20 is turned
OFF or the A-10 is in standby mode before
detaching the cord.
3
10 mm
IN
OUT
CONTROL
Caution
• When using only one set of speaker terminals
(SPEAKERS A or SPEAKERS B), or when utilizing
bi-wiring connections, the speaker used should
have a nominal impedance between 4 Ω and
16 Ω. When using both sets of terminals, the
connected speakers should have nominal
impedance between 8 Ω and 32 Ω. Consult the
instructions accompanying your speakers for
details regarding the impedance value.
• Make sure the positive and negative (+/–) terminals
on the amplifier match those on the speakers.
• These speaker terminals carry HAZARDOUS live
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
• Make sure that all the bare speaker wire is twisted
together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the
back panel it may cause the power to cut off as a
safety measure.
6
En
To other Pioneer
component
equipped with
CONTROL IN jack
Other Pioneer
component equipped
with CONTROL IN/
OUT jacks
A-30/A-20
A-30/A-20
remote
control
Caution
• The use of a power cord other than the one provided
will invalidate the warranty, since Pioneer will not
be responsible for any damage incurred. (The
power cord provided with the model A-30 has a
rated current capacity of 10 A, while the cord
provided with the A-20/A-10 has a rated current
capacity of 2.5 A.)
• Do not use any power cord other than the one
supplied with this unit.
• Do not use the supplied power cord for any purpose
other than that described below.
After you’ve finished making all connections, plug the
unit into an AC outlet.
Aim remote control
at the sensor on the
A-30/A-20.
A-30’s rear panel
Note
• For connections use a commercially available
monaural miniplug cord (without resistor).
• When connecting the CONTROL IN/OUT jacks,
commercially available audio cords must also be
used to make analog connections. Merely
connecting the CONTROL IN/OUT jacks alone will
not allow proper system control.
• When a control cord is connected to the A-30/A20’s CONTROL IN jack, the unit cannot be
controlled by pointing the remote control at the A30/A-20 (the remote sensor is automatically
disabled).
To AC outlet
Power cord
1 Plug the supplied power cord into the
AC IN socket on the rear panel of the unit.
2
Plug the other end into an AC outlet.
A30_SYXE8.book
7 ページ
2012年2月16日 木曜日 午前8時58分
Controls and displays
03
6
Remote sensor (Except A-10)
Front panel
8
1
2
4
3
7
Use to connect headphones. No sound is produced
when the POWER AMP DIRECT button is ON.
5
A-30
8
9
10
STANDBY/APD indicator
When power is set to standby, the indicator lights red.
When the Auto Power Down (APD) function is on, the
indicator lights green (page 11).
3
SPEAKERS A button/indicator
14
SPEAKERS B button/indicator
Use this button to listen to the speaker system
connected to SPEAKERS B terminals.
On : The indicator lights. Sound is heard from the
speaker system. (Sound will also be produced from the
PHONES jack.)
Off : The indicator goes off. No sound is heard from the
speaker system. Set to this position when listening with
headphones.
5
LOUDNESS button/indicator
Use when listening at low volume levels.
On : The indicator lights: Boosts low and high
frequencies to give added punch to playback even at a
low volume level.
Off : The indicator goes off: Should normally be left in
this position.
• This button does not operate when the DIRECT
button is in the on position.
• When sound volume is raised, the amount of
change produced by the LOUDNESS circuit is
reduced.
10 TREBLE tone control
Use to adjust the high-frequency tone. The center
position is the flat (normal) position. When turned to the
right, high-frequency tones are emphasized; when
turned to the left, high-frequency tones are deemphasized.
• This button does not operate when the DIRECT
button is in the on position.
11 BALANCE control
Should normally be left in the center position. Adjust
balance if the sound is louder from one of the speakers.
If the right side is louder, turn toward the L (left) position
and if the left side is louder, turn toward the R (right)
position.
• This button does not operate when the DIRECT
button is in the on position.
12 VOLUME control
Español
Use this button to listen to the speaker system
connected to SPEAKERS A terminals.
On : The indicator lights. Sound is heard from the
speaker system. (Sound will also be produced from the
PHONES jack.)
Off : The indicator goes off. No sound is heard from the
speaker system. Set to this position when listening with
headphones.
4
13
Press this button when the A-30 is to be used as a power
amplifier (page 10).
Nederlands
2
12
14 POWER AMP DIRECT button/indicator
(A-30 only)
Italiano
/I STANDBY/ON
Switches the amplifier between off and on.
When power is turned on, the power indicator in the
center of the button will light.
• On the A-10 model, this switches the amplifier
between standby and on.
11
BASS tone control
Use to adjust the low-frequency tone. The center position
is the flat (normal) position. When turned to the right,
low-frequency tones are emphasized; when turned to the
left, low-frequency tones are de-emphasized.
• This button does not operate when the DIRECT
button is in the on position.
Turn the knob clockwise or counterclockwise so that the
indicator lights for your desired input source. Turning
the knob clockwise causes the lit indicator to right.
Turning counterclockwise causes it to left. When the
remote control’s MUTE button is pressed to mute the
sound, the indicator for the input source selected with
the INPUT SELECTOR knob flashes.
Deutsch
1
7
DIRECT button/indicator
On : The indicator lights: When this button is set to ON,
sound signals are output directly, without being passed
through the various adjustment circuits (BASS, TREBLE,
BALANCE, LOUDNESS). This allows reproduction of the
signals with greater fidelity, but it disables any settings
made with the BASS, TREBLE, BALANCE or LOUDNESS
controls.
Off : The indicator goes off: The signal passes through
the various frequency adjusting circuits. When the
indicator is OFF, adjustments can be made with the
BASS, TREBLE, BALANCE, and LOUDNESS controls.
9
6
PHONES jack
13 INPUT SELECTOR knob/indicators
Français
Controls and displays
Receives the signals from the remote control (page 4).
English
Chapter 3:
Use to adjust the volume level. (Also allows adjustment
of the headphone sound volume.)
Русский
7
En
A30_SYXE8.book
03
8 ページ
2012年2月16日 木曜日 午前8時58分
Controls and displays
Rear panel
See pages 5-6 for details regarding connections.
2
1
8
2
7
1
10
2
9
3
2
En
5
2
6
A-30
12
2
11
13
GND (Turntable ground) terminal
14
10 AUX IN terminals
This ground terminal is designed to help reduce noise
when a turntable is connected. It is not a safety ground.
11 NETWORK IN terminals
2
SPEAKERS A terminals (Right channel)
12 RECORDER IN/OUT terminals
3
SPEAKERS B terminals (Right channel)
4
SPEAKERS B terminals (Left channel)
13 POWER AMP DIRECT IN terminals (A-30
only)
5
SPEAKERS A terminals (Left channel)
6
AC IN jack
Connect power cord to here and an AC wall socket.
8
4
2
7
PHONO (MM) IN terminals
8
TUNER IN terminals
9
SACD/CD IN terminals
When using the A-30 as a power amplifier, connect the
pre-amplifier here (page 10).
14 CONTROL IN/OUT jack (Except A-10)
A30_SYXE8.book
9 ページ
2012年3月6日 火曜日 午前11時13分
Controls and displays
03
A-30
STANDBY/ON
DIMMER
TUNER
PHONO
AUX
1
8
3
RECORDER
OPTION
9
INPUT
SACD PLAYER
2
7
FUNC
NETWORK AUDIO PLAYER FUNC
4
3
10
3
11
4
4 NETWORK AUDIO PLAYER control
buttons
Use to control Pioneer network audio player.
5
LOUDNESS
Use to set the loudness circuit ON/OFF (page 7).
LOUDNESS VOLUME
5
A
6
10
B
11
12
4
3
12
SOUND
4
ENTER
DIRECT
4
3
RETURN
APD
13
3
DIRECT
Press to access Direct listening (page 7).
DIMMER
This button allows the illumination of the unit's front
panel indicators to be set in three levels (does not affect
the STANDBY indicator).
9
INPUT +/–
Use to change the input source. The source changes as
below.
SACD/CD  NETWORK  PHONO  TUNER 
AUX  RECORDER  Return to the beginning.
10 SPEAKERS A button/indicator
11 SPEAKERS B button/indicator
Use this button to listen to the speaker system
connected to SPEAKERS B terminals.
12 VOLUME +/–
Español
Use this button to listen to the speaker system
connected to SPEAKERS A terminals.
Nederlands
HOME MENU
7
8
NETWORK AUDIO PLAYER
SETUP
MUTE
Italiano
6
6
Mutes/unmutes the sound.
SPEARKERS
MUTE
7
SACD PLAYER control buttons
Use to control Pioneer SACD player.
(Cannot be used to perform playback/pause on the
PD-D6/PD-D6MK2/PD-D9/PD-D9MK2 models.)
Deutsch
3
5
Input selector buttons
Press to select an input source. These select the
component connected to the corresponding input on the
rear panel.
• When the A-30 is connected, the OPTION button is
disabled.
Français
8
SACD/CD NETWORK
2
2
A-20
1
 STANDBY/ON
Switches the amplifier between standby and on.
English
1
Remote control (Except A-10)
Use to set the listening volume.
Use to set the Auto Power Down function to ON/OFF
(page 11).
Русский
13 APD
9
En
A30_SYXE8.book
04
10 ページ
2012年2月16日 木曜日 午前8時58分
Operation
Chapter 4:
Set the power to Standby
Operation
1 Press the remote control’s  STANDBY/
ON button.
iPod dock, etc
Turntable
SACD/CD player
NETWORK AUDIO PLAYER
FUNCTION
STANDBY
PURE AUDIO




CD recorder or
tape deck
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
Network audio player
/I STANDBY/ON
Tuner
MENU
N-50


Hi-Bit 32

iPod/USB
5V 2.1A
2
6
The next time you wish to turn on the power, press the
remote control’s  STANDBY/ON button.
• In the case of the A-30/A-20, If the front panel’s
 STANDBY/ON button is pressed, the power will
be turned off. In this case, if the power is off,
pressing the remote control’s  STANDBY/ON
button will not turn on the power. To turn on the
power again, press the front panel’s  STANDBY/
ON button.
Note
Playback
Playback
6
6
3
4 Start playback of the component you
selected in step 1.
2
5 Adjust playback volume with VOLUME
control.
Turn power ON to the unit.
VOLUME
Select the source you want to playback.
SACD/CD NETWORK
TUNER
AUX
PHONO
RECORDER
Select the playback component.
• When using the A-30’s remote control, the INPUT
+/– button can be used to select the component.
• When using the front panel controls, rotate the
INPUT SELECTOR knob.
En
5
1 Turn on the power of the playback
component.
• If the unit is in the standby mode, press the remote
control’s  STANDBY/ON button.
10
When a pre-amplifier is connected to the unit’s POWER
AMP DIRECT terminals, the unit can be used as a power
amplifier.
1 Press the POWER AMP DIRECT button
on the front panel of the unit.
Playback
3
When using the unit as a power amplifier
(A-30 only)
6 Adjust the tone to your preference using
the BASS and TREBLE controls, and
LOUDNESS button.
If the DIRECT button has been set to ON, these controls
are disabled.
• If the power cord is disconnected when the unit is
in the standby mode the unit will turn off, but when
the cord is then reconnected, the unit will not
automatically turn on. After reconnecting the
power cord, press the remote control’s
 STANDBY/ON button to turn the power on.
The POWER AMP DIRECT indicator will light.
Caution
• When the POWER AMP DIRECT indicator is
lighted, operations change as follows:
– The unit’s front-panel VOLUME, BASS, TREBLE,
and BALANCE controls are disabled. These
adjustments are controlled by the component
connected to the unit’s POWER AMP DIRECT
terminals.
– When the POWER AMP DIRECT indicator is
lighted, sound volume from the A-30 will
automatically be fixed at its maximum output.
When using this unit as a power amplifier,
check the output level of the component
connected to the POWER AMP DIRECT
terminals and set it to a low level as appropriate
before turning on the POWER AMP DIRECT
indicator. If the sound volume of the component
connected to the POWER AMP DIRECT
terminals is initially set to a high output level,
loud sound may suddenly be output when the
POWER AMP DIRECT indicator lights.
– Sound is not produced from the PHONES jack
and RECORDER OUT terminals.
• For more information, consult the operating
instructions for the component connected to the A30’s POWER AMP DIRECT terminals.
A30_SYXE8.book
11 ページ
2012年3月6日 火曜日 午前11時13分
Operation
04
To set for automatic standby status (Auto Power Down)
You can make an audio recording from any audio source connected to the amplifier.
iPod dock, etc
Turntable
SACD/CD player
iPod
Music>
Extras>
Settings>
Shuffle Songs
Backlight
Network audio player
FUNCTION
STANDBY
PURE AUDIO




N-50
MENU

1 If the unit’s power is ON, hold the unit’s front-panel DIRECT button and LOUDNESS
button depressed simultaneously for three seconds.
Français
NETWORK AUDIO PLAYER
/I STANDBY/ON
Tuner
When this condition is set, if no input signal is detected for 30 minutes, the unit will automatically enter standby
status.

Hi-Bit 32

iPod/USB
5V 2.1A
Playback
1
Note
1
Select the source you want to record.
SACD/CD NETWORK
1 When power is in standby mode, hold the front-panel’s DIRECT button and
SPEAKERS A button depressed simultaneously for five seconds.
AUX
2 Start recording, then start playback of
the source component.
Turn power ON to the unit.
Español
2
Nederlands
TUNER
PHONO
Restoring all the settings to the factory default settings
Italiano
• Depending on the device connected, excessive noise produced by the device may be interpreted as an audio
signal, thus preventing the Automatic Power-Down function from operating.
Audio recording component
(CD recorder, tape deck, etc.)
Deutsch
When this condition is set to ON, the STANDBY/APD indicator on the unit’s front panel will light green. Press the
buttons again to disable the setting.
• This condition can also be set by means of the APD button on the A-30’s remote control.
• The factory default setting is ON.
Recording
English
Making an audio recording
Русский
11
En
A30_SYXE8.book
05
12 ページ
2012年2月16日 木曜日 午前8時58分
Additional information
Chapter 5:
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
Problem
Remedy
The power does not turn on.
• Is the power plug disconnected from the power outlet? Connect the power plug
correctly to its outlet (page 6).
•Is the power cord disconnected from the AC IN connector? Connect the power cord
correctly (page 6).
Power turns off.
•Is the Auto Power Down function turned ON? If you do not want the power to turn off
automatically, disable the Auto Power Down function (page 11).
During playback, sound stops, and
the STANDBY/APD indicator flashes
red at about 1 second intervals.
•The unit’s internal temperature has risen and the safety circuit has operated.
- Turn power OFF, and allow the unit to cool before turning the power ON again.
- Install the unit in a location with better ventilation.
- Confirm that the unit is installed correctly; if the unit is turned on again without
being allowed to cool, the same symptoms may appear (page 4).
During playback, sound stops, and
the STANDBY/APD indicator flashes
red at about 2 second intervals.
•Are you using speakers with impedance values not supported by this unit? Confirm
the speaker’s nominal impedance value (page 6).
•Are any speaker cables loose from the SPEAKERS terminals and touching other
wires or the surface of the rear panel? Disconnect the power cord and reconnect the
speaker cables correctly (page 6).
When power is turned on, the
STANDBY/APD indicator flashes at
irregular intervals.
•The unit’s circuitry is damaged. Disconnect the power cord and consult your dealer
or nearest Pioneer authorized service center.
No sound is output when a function is •A connection cable is disconnected or connected improperly. Check your
selected.
connections (page 5).
•Connectors or pin plugs on a cable are dirty. Wipe off any dirt from connectors and
pin plugs.
•Confirm that the unit’s input selector is set to the desired playback component. Set
selector correctly (page 10).
•In the case of the A-30/A-20, press MUTE on the remote control to turn muting off
(page 9).
No sound from one speaker.
12
En
•Are the connection cables or speaker cables disconnected on one side? Reconnect
securely (page 5).
Problem
Remedy
Can’t operate the remote
control.
•Replace the battery (page 4).
•Operate within 7 m, 30° of the remote sensor on the front panel (page 4).
•Remove the obstacle or operate from another position.
•Avoid exposing the remote sensor on the front panel to direct light.
•Is the control cord for one component connected improperly? Confirm correct
connections (page 6).
Can’t change input source on A-30.
•Check whether POWER AMP DIRECT function is ON. If so, press the front panel’s
POWER AMP DIRECT button to turn the function OFF (page 10).
Cleaning the unit
• Use a polishing cloth or dry cloth to wipe off dust
and dirt.
• When the surface is dirty, wipe with a soft cloth
dipped in some neutral cleanser diluted five or six
times with water, and wrung out well, and then
wipe again with a dry cloth. Do not use furniture
wax or cleansers.
• Never use thinners, benzine, insecticide sprays or
other chemicals on or near this unit, since these
will corrode the surface.
A30_SYXE8.book
13 ページ
2012年2月16日 木曜日 午前8時58分
Additional information
Amplifier section
Power output specification is for when power supply is 230 V.
A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 W + 70 W
A-20, A-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W + 50 W
(THD 0.1 %, 4 Ω)
A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 W+40 W
A-20, A-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 W+30 W
(THD 0.05 %, 8 Ω)
•
Input (Sensitivity/Impedance)
SACD/CD, NETWORK, TUNER, AUX, RECORDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/50 kΩ
POWER AMP DIRECT (A-30 only) . . . . . . . . . . . 1 V/10 kΩ
PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . 2.8 mV/50 kΩ
•
Output (Level/Impedance)
•
Frequency response
SACD/CD, NETWORK, TUNER, AUX, RECORDER
Remote control (Except A-10) . . . . . . . . . . . . . . . . . . . . . 1
AAA/IEC R03 dry cell batteries (Except A-10) . . . . . . . . 2
Power cord
Warranty card
Operating instructions (This document)
Note
• Specifications and the design are subject to
possible modifications without notice, due to
improvements.
• Corporation and product names mentioned herein
are trademarks or registered trademarks of the
respective corporations.
Nederlands
. . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Hz to 100 kHz
dB*
PHONO (MM) . . . . . . . . . . . . . .20 Hz to 20 kHz ±0.5 dB*
* Measured with DIRECT button switched on.
Accessories
Italiano
RECORDER OUT . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kΩ
PHONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 mV/32 Ω
Power requirements
. . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V to 230 V, 50 Hz
Power consumption
A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 W
A-20/A-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 W
In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3 W
Dimensions
. . . . . . . . . . . . . 435 mm (W) x 128 mm (H) x 360 mm (D)
Weight (without package)
A-30 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 kg
A-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 kg
A-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 kg
Deutsch
Audio section
Miscellaneous
Français
• Continuous power output (both
channels driven at 20 Hz to 20 kHz)
English
Specifications
05
• Tone control
(When VOLUME is set to -30 dB)
Bass. . . . . . . . . . . . . . . . . . . . . . . . . . . . .± 10 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . . . . . . .± 10 dB (10 kHz)
• Signal-to-Noise Ratio (IHF SHORTED,
A-NETWORK)
•
Español
SACD/CD, NETWORK, TUNER, AUX, RECORDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 dB*
PHONO (MM, 2.8 mV input) . . . . . . . . . . . . . . . . . 77 dB*
* Measured with DIRECT button switched on.
Speaker load impedance
A, B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω to 16 Ω
A+B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω to 32 Ω
Bi-wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ω to 16 Ω
Русский
© 2012 PIONEER CORPORATION.
All rights reserved.
13
En
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising