- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- MULTIPLEX
- Multicharger Ln 3008 Equ
- Owner's manual
advertisement
MULTIcharger
LN-3008
Anleitung
Instructions
Instructions
Instrucciones
Istruzioni
2 – 6
11
16
21
26
Rev.: 07.04.08
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Bedienungsanleitung MULTIcharger LN-3008 EQU
1. Einleitung
Wir freuen uns, dass Sie sich für unseren
MULTIPLEX MULTIcharger LN-3008 EQU,
# 9 2540, entschieden haben.
Mit dem MULTIcharger LN-3008 EQU sind
Sie im Besitz eines hochleistungsfähigen
12 Volt Ladegeräts mit einfachster Bedienung und in dieser Klasse einzigartigen Features, wie dem integrierten EQUALIZER zum
Abgleich der Einzelzellenspannungen bei
LiXX Akkus.
Die wichtigsten Merkmale des MULTIcharger
LN-3008 EQU sind:
• Von 2 bis 3S Zellen LiPo / LiIo / LiFe Akkus und von 4 bis 8 Zellen NiMH / NiCd Akkus ladbar
• Integrierter EQUALIZER (mit FlightPower
/ Thunder Power kompatiblem Stecksystem)
Æ MULTIPLEX Li-BATT BX Akkus können direkt an den EQUALIZER Port des
LN-3008 EQU angeschlossen werden – für Akkus mit anderen Stecksystemen gibt es separate Adaptersätze, siehe Kapitel 8. - Zubehör
• Einfachste Bedienung
Wir sind sicher, dass Sie Ihren MULTIPLEX
MULTIcharger LN-3008 EQU nach einer kurzen Kennenlernphase, durch die Sie diese
Bedienungsanleitung begleiten soll, bald zu schätzen wissen.
Ihr MULTIPLEX-Team
2. Technische Daten
Eingangsspannung 11 - 15 V
Akkutypen und
Zellenzahlen
LiPo/LiIo/LiFe: 2 - 3S Zellen
NiMH/NiCd: 4 - 8 Zellen
Ladestrom
(Ladeleistung)
0,1 - 3 A
(max. 30 W)
Erhaltungsladestrom 0 - 100 mA
Integrierter für 2 bis 3S LiXX Akkus
EQUALIZER
Ausgleichsstrom des EQUALIZERS max. 42 mA
Abgleichgenauigkeit des EQUALIZERS ca. 32,5 mV
Abschaltverfahren Delta-Peak Abschaltung für
NiMH-Akkus (-3 mV/Zelle) und für
NiCd-Akkus (-5 mV/Zelle)
Ladung mit Konstantstrom/Konstantspannung für
LiXX-Akkus
Ladeanschluss zwei 4 mm Buchsen
EQUALIZER-
Anschlüsse ein MULTIPLEX /
FlightPower / Thunder
Power kompatibler Anschluss
Anschlüsse für Anschluss an ein stabilisiertes Netzteil oder an eine Autobatterie
Abmessungen zwei Anschlusskabel mit
4 mm Bananenstecker für direkten Anschluss an ein
Netzgerät. Krokodilklemmen mit 4 mm Buchse für Anschluss an Autobatterie beiliegend ca. 120 x 80 x 25 mm
• Automatische Erkennung der Zellenzahl des angeschlossenen Akkus
• Laden von Lithium-Akkus mit und ohne
EQUALIZER Funktion
• Laden von Nickel-Akkus
2.2. Sicherheitsfunktionen des Laders
• Verpolschutz an Ein- und Ausgang
• Schutz vor zu niedriger und zu hoher Eingangsspannung
• Integrierter Safety Timer
• LEDs zur Statusanzeige
• Buzzer zur Benutzereingabebestätigung
• Anzeige von Fehlermeldungen über integrierten Buzzer und über LEDs
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Seite 2/29
Bedienungsanleitung MULTIcharger LN-3008 EQU
3. Sicherheitshinweise
! Diese Bedienungsanleitung ist Bestand- teil des Produktes. Sie beinhaltet wichtige
Informationen und Sicherheitshinweise.
Sie ist deshalb jederzeit griffbereit aufzubewahren und beim Verkauf des Produktes an Dritte weiterzugeben.
! Anleitung sorgfältig lesen! Sicherheits- hinweise beachten!
Gerät nicht in Betrieb nehmen, bevor Sie diese Bedienungsanleitung und die folgenden (bzw. in der Anleitung enthaltenen oder separat beiliegenden) Sicherheitshinweise sorgfältig und vollständig gelesen haben.
! Gerät nicht öffnen. Nehmen Sie unter keinen Umständen technische Veränderungen vor. Verwenden Sie ausschließlich
Originalzubehör und Originalersatzteile.
! Falls Sie das Gerät im Zusammenspiel mit Produkten anderer Hersteller betreiben, vergewissern Sie sich über deren
Qualität und Funktionstüchtigkeit. Jede neue bzw. veränderte Konstellation ist vor
Inbetriebnahme einem sorgfältigen Funktionstest zu unterziehen. Gerät nicht in Betrieb nehmen, wenn etwas nicht in Ordnung zu sein scheint. Zuerst Fehler suchen und beheben.
! Beachten Sie stets die Ladehinweise des Akkuherstellers.
! Schützen Sie das Ladegerät vor Staub,
Feuchtigkeit, Regen, Hitze und Vibrationen.
! Das Ladegerät kann während des Be- triebs sehr warm werden.
Vorsicht beim Anfassen!
Die Schlitze im Gehäuse dienen der Kühlung des Gerätes und dürfen nicht abgedeckt oder verschlossen werden. Das Gerät muss zum Laden frei stehen, damit die
Luft ungehindert zirkulieren kann. Des
Weiteren darf es nicht direkter Sonneneinstrahlung ausgesetzt werden.
! Das Ladegerät und der zu ladende Akku müssen während des Betriebes auf einem nicht brennbaren, hitzebeständigen und elektrisch nicht leitenden Untergrund stehen. Ladegerät, Akku und Ladekabel niemals direkt auf die Auto-Karosserie stellen! Das Gerät auch nicht in der Nähe leicht brennbarer Materialien betreiben.
! Schließen Sie immer nur einen Akku an den Ladeanschluss und den EQUALIZER
Port Ihres Ladegerätes an. Versuchen Sie niemals, mehrere Akkupacks gleichzeitig zu laden.
! Laden Sie Ihre Akkus stets unter Auf- sicht und lassen Sie das Ladegerät auch nicht unbeaufsichtigt an der Stromversorgung angeschlossen!
! Laden Sie nur Zellen gleichen Typs und mit derselben Kapazität im Verbund (Akkupack).
! Laden Sie Ihre Akkus erst, nachdem diese auf Umgebungstemperatur abgekühlt sind.
! Achten Sie beim Anschluss des Lade- gerätes an die Kfz-Batterie oder ein stabilisiertes Netzteil stets auf die korrekte Polung. Niemals verpolt anschließen.
! Anschlusskabel und Ladeausgänge dürfen niemals untereinander verbunden werden. Lade- und Anschlusskabel dürfen während des Betriebs nicht aufgewickelt sein.
! Trennen Sie Ihren Akku unmittelbar nach Ende des Ladevorgangs vom MULTIcharger LN-3008 EQU.
4. Allgemeine Ladehinweise
• Beachten Sie den maximal zulässigen Ladestrom Ihres Akkus.
• Das verwendete Ladekabel muss einen ausreichenden, großzügig dimensionierten
Kabelquerschnitt aufweisen und darf nicht länger als 30 cm sein. Ein zu dünnes und
/oder zu langes Kabel kann den Ladevorgang durch seinen Widerstand negativ beeinflussen.
• Achten Sie auf sicheren Kontakt aller Verbindungen. Alle Verbindungen müssen frei von Wackelkontakten sein.
• Prüfen Sie vor dem Start des Ladevorgangs, dass Akku und gewählter Akku Modus zusammenpassen und alle zum verwendeten
Akkutyp notwendigen Einstellungen korrekt vorgenommen wurden.
• Laden Sie Ihre Akkus niemals unbeauf- sichtigt.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Seite 3/29
Bedienungsanleitung MULTIcharger LN-3008 EQU
5. Das Ladegerät
Sicherung
Stromeinstelldrehknopf
Lüftungsschlitze
Bedientasten
6. Inbetriebnahme des
EQUALIZER
Port
Ladeanschluss
MULTIcharger LN-3008 EQU
• Beachten Sie bei der Durchführung der folgenden Arbeitsschritte die Sicherheitshin-
weise und die allgemeinen Ladehinweise.
• Schließen Sie den MULTIcharger LN-3008
EQU mit den beiliegenden Krokodilklemmen an Ihre Autobatterie an. Alternativ können
Sie das Ladegerät an ein stabilisiertes Netzteil (unter Verwendung der 4 mm Bananenstecker) mit einer Ausgangsspannung von
11 V bis 15 V anschließen. Achten Sie auf korrekte Polung (rot = Pluspol, schwarz =
Minuspol). Das Ladegerät befindet sich nun im Standby Modus und die POWER LED leuchtet.
• Verbinden Sie Ihr Ladekabel mit dem Lader
(
Æ NiXX/LiXX Charge) und danach Ihren
Akku mit dem Ladekabel. Polarität beachten
(rot = Pluspol, schwarz = Minuspol)!
• Wenn Sie einen Lithium Akku (LiPo, LiIo oder LiFe) mit 2S oder 3S Zellen laden möchten, so verbinden Sie dessen Balancer
Anschluss zusätzlich auch mit dem EQUA-
LIZER Port des MULTIcharger LN-3008
EQU. Achten Sie stets auf die korrekte Polung. (Passende Adaptersätze zum Anschluss Ihres Lithium Akkus mit Graupner / robbe oder Polyquest Balancer Anschluss, finden Sie im Kapitel 8. - Zubehör).
• Funktion des eingebauten EQUALIZER:
Nutzen Sie diese Funktion, um eine Spannungsdifferenz der Einzelzellen Ihres LiXX
Akkus bereits beim Laden durch den MUL-
TIcharger LN-3008 EQU ausgleichen zu lassen. Somit stellen Sie sicher, dass alle
Einzelzellen Ihres Akkus beim Beenden des
Ladevorgangs dieselbe Ladeschlussspannung besitzen.
• Beispiel: Ladung eines 3S LiPo Akkus ohne
Nutzung des eingebauten EQUALIZER:
Die Einzelzellenspannungen liegen gegen
Ende des Ladevorgangs bei 4,0 V, 4,2 V und
4,4 V. Dies entspricht einer Gesamtspannung von 12,6 V, bei der das Ladegerät den
Ladevorgang beenden würde.
Die Zelle mit 4,4 V wäre in diesem Beispiel jedoch bereits überladen und beschädigt, wobei die Zelle mit 4,0 V noch nicht vollständig geladen wäre.
Bei Nutzung des eingebauten EQUALIZER des MULTIcharger LN-3008 EQU gleicht dieser die Spannungsdifferenzen bereits während des Ladevorgangs aus. Er sorgt dafür, dass alle drei Zellen gleichzeitig eine
Ladeschlussspannung von 4,2 V erreichen und somit optimal geladen sind.
• Durch Drücken der Taste BATT TYPE wechseln Sie den Akkutyp, der aktuell eingestellte Akkutyp wird über die entsprechende LED angezeigt.
• Der MULTIcharger LN-3008 EQU kann folgende Akkutypen laden:
- Lithium-Polymer (LiPo)
Æ 3,7 V / Zelle
- Lithium-Ionen (LiIo) Æ 3,6 V / Zelle
- Lithium-Ferrit (LiFe) Æ 3,3 V / Zelle
- Nickel-Metal-Hydrid (NiMH)
- Nickel-Cadmium (NiCd) Akkus
• Mit dem Drehknopf CHARGE CURRENT stellen Sie den Ladestrom für Ihren Akku ein. Vorsicht: Verstellen Sie den Lade- strom während des Ladevorgangs nicht
unbeabsichtigt!
• Laden Sie Ihre LiPo und LiIo Akkus stets
mit 1C (C = Kapazität / Stunde). D.h. einen
Akku mit einer Kapazität von 2.100 mAh laden Sie mit ca. 2,1 A! LiFe Akkus laden Sie maximal mit dem Strom, den der Herstel-
ler angibt.
Der Lader lädt nach dem Konstantstrom/Konstantspannungsverfahren, beendet den Ladevorgang jedoch spätestens nach 3 Stunden (Safety Timer).
• Laden Sie NiMH und NiCd Akkus eben- falls mit 1C. Laden Sie jedoch nur ausdrücklich als schnellladefähig gekennzeichnete NiMH und NiCd Akkus mit dem
MULTIcharger LN-3008 EQU. Der Lader beendet den Ladevorgang automatisch nach
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Seite 4/29
Bedienungsanleitung MULTIcharger LN-3008 EQU dem Delta-Peak Abschaltverfahren, jedoch spätestens nach 1,5 Stunden (Safety Timer).
• Durch langes Drücken der Taste START/
STOP starten Sie den Ladevorgang. Der
Lader ermittelt nun automatisch die Zellenzahl Ihres Akkus und lädt diesen. Während des Ladevorgangs leuchten die CHARGE
LED und die LED des eingestellten Akkutyps. Haben Sie den Balancer Anschluss Ihres LiXX Akkus am EQUALIZER Port angeschlossen, zeigt der Lader den gleichzeitigen EQUALIZE Vorgang durch Blinken der
LED des eingestellten LiXX Akkutyps an.
• Sobald der Akku voll geladen ist, beendet der Lader den Ladevorgang automatisch und zeigt dies durch mehrmaliges Piepsen und durch Aufleuchten der CHARGE END
LED an.
• Bevor Sie den nächsten Akku laden, müssen
Sie die Taste START/STOP erneut drücken.
Anschließend befinden Sie sich wieder im
Standby Modus.
• Während des Ladevorgangs können Sie diesen durch Drücken der Taste
START/STOP unterbrechen, bevor Ihr Akku voll geladen ist.
6.2. Lithium Akkus equalizen
Nutzen Sie diese Funktion zum Abgleich der
Einzelzellenspannungen Ihres LiXX Akkus, ohne den Akku zu laden.
• Verbinden Sie Ihr Ladekabel mit dem Lader
( Æ NiXX/LiXX Charge) und danach Ihren
Lithium Akku mit dem Ladekabel. Polarität beachten (rot = Pluspol, schwarz = Minuspol)!
• Verbinden Sie den Balancer Anschluss des
LiXX Akkus zusätzlich auch immer mit dem
EQUALIZER Port des Laders. Achten Sie stets auf die korrekte Polung!
• Wählen Sie den gewünschten Lithium Akkutyp durch Drücken der Taste BATT TYPE, der aktuell eingestellte Akkutyp wird über die entsprechende LED angezeigt.
• Die Stellung des Drehknopf CHARGE
CURRENT ist unbedeutend während des
EQUALIZE Vorgangs.
• Durch kurzes Drücken der Taste START/
STOP starten Sie den EQUALIZE Vorgang.
Während des EQUALIZE Vorgangs blinkt
nur die LED des eingestellten LiXX Akkutyps. Die CHARGE LED bleibt aus.
• Sobald die Spannungen der Einzelzellen
Ihres LiXX Akkus abgeglichen sind, zeigt der
Lader dies durch mehrmaliges Piepsen und durch Aufleuchten der CHARGE END LED an.
• Während des EQUALIZE Vorgangs können
Sie diesen durch Drücken der Taste
START/STOP unterbrechen, bevor der Abgleich der Einzelzellenspannungen abgeschlossen ist.
7. Fehlermeldungen
Die Fehler werden über Piepsen und über das mehrmalige Blinken der CHARGE und der
CHARGE END LED ausgegeben.
Fehlerursache
LED
Blinkrhythmus
Eingangsspannung unter 11 V oder über 15 V
1mal
Kein Akku am Ladegerät angeschlossen oder Fehler in der Verbindung zwischen Ladegerät und Akku
Akku verpolt am Ladegerät angeschlossen
2mal
3mal
NiXX Akku mit weniger als 4 oder mehr als 8 Zellen oder LiXX Akku mit weniger als 2S oder mehr als 3S Zellen am Lader angeschlossen
Balancer Anschluss eines LiXX Akkus war während des Startens des
EQUALIZE Vorgangs nicht am
EQUALIZER Port angeschlossen
oder Balancer Anschluss eines LiXX
Akkus wurde während des Lade-
/EQUALIZE Vorgangs vom EQUALI-
ZER Port abgezogen oder Balancer-
Anschluss eines LiXX Akkus ist mit
EQUALIZER Port verbunden, der
Lader befindet sich jedoch im NiXX
Modus oder Einzelzellenspannung eines LiXX Akkus ist zu niedrig:
- LiPo Akkus: unter 2,75 V pro Zelle
- LiIo Akkus: unter 2,75 V pro Zelle
- LiFe Akkus: unter 2,00 V pro Zelle oder zu hoch:
- LiPo Akkus: über 4,30 V pro Zelle
- LiIo Akkus: über 4,20 V pro Zelle
- LiFe Akkus: über 3,90 V pro Zelle
Problem innerhalb des Laders oder bei überschreiten des Safety Timers
(1,5 Stunden bei NiXX und 3 Stunden bei LiXX Akkus)
4mal
5mal
6mal
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Seite 5/29
Bedienungsanleitung MULTIcharger LN-3008 EQU
8. Zubehör
Von der Gewährleistung ausgeschlossen sind
Defekte und Fehlfunktionen, die verursacht
Sender-Ladekabel (Diodenstecker) # 8 6020 wurden durch:
• Unsachgemäßen Betrieb, falsche Anschlüs-
Sender-Ladekabel PROFI-CAR
Direktladekabel Senderakku
# 8 6022
# 8 6021 se, Verpolung
• Verwendung von nicht originalem
Empfängerakku-Ladekabel MP-RC # 8 5106
MULTIPLEX-Zubehör
• Veränderungen / Reparaturen, die nicht von
Empfängerakku-Ladekabel (UNI) # 8 5094
MULTIPLEX oder einer autorisierten MUL-
Ladekabel für Akkus mit M6-
# 9 2516
Anschluss
Adaptersatz Polyquest
Adaptersatz Graupner / robbe
9. CE Konformitätserklärung
# 8 6001
# 8 6002
TIPLEX-Service-Stelle ausgeführt wurden
• Versehentliche oder absichtliche Beschädigung
• Defekte auf Grund normaler Abnutzung
• Betrieb außerhalb der technischen Spezifikationen
Die Bewertung des Gerätes erfolgt nach europäisch harmonisierten Richtlinien.
Sie besitzen daher ein Produkt, das hinsichtlich der Konstruktion die Schutzziele der Europäischen Gemeinschaft zum sicheren Betrieb der Geräte erfüllt.
Die Konformitätserklärung des Gerätes kann bei Bedarf bei MULTIPLEX unter den in der
Fußzeile aufgeführten Kontaktdaten angefordert werden.
10. Haftungsausschluss
Die MULTIPLEX Modellsport GmbH & Co.KG
übernimmt keine Haftung für Verluste, Schäden oder Kosten, die sich aus einer fehlerhaften Verwendung und dem Betrieb des Produkts ergeben oder damit zusammenhängen.
Die Verpflichtung zum Schadenersatz, gleich aus welchem Rechtsgrund, ist auf den Rechnungswert der am Schadenereignis unmittelbar beteiligten MULTIPLEX-Produkte begrenzt, soweit das gesetzlich zulässig ist.
Dies gilt nicht, wenn eine Haftung nach zwingenden gesetzlichen Vorschriften wegen Vorsatzes oder grober Fahrlässigkeit vorliegt.
Weiterhin übernimmt die MULTIPLEX Modellsport GmbH & Co.KG keine Gewähr für die Vollständigkeit und Richtigkeit der Unterlagen, die dem Ladegerät beiliegen.
11. Gewährleistung
Für unsere Produkte leisten wir entsprechend den derzeit geltenden gesetzlichen Bestimmungen Gewähr. Wenden Sie sich mit Gewährleistungsfällen an den Fachhändler, bei dem Sie das Gerät erworben haben.
12. Beratung / Service
Wir haben uns sehr bemüht diese Bedienungsanleitung so zu gestalten, dass Sie darin auf jede Frage schnell und einfach eine
Antwort finden. Sollte trotzdem eine Frage zu
Ihrem neuen Ladegerät offen bleiben, wenden
Sie sich an Ihren Fachhändler, der Ihnen gerne mit Rat und Tat zur Seite steht.
Die Anschriften unserer Servicepartner finden
Sie auf unserer Homepage: www.multiplex-rc.de unter
KONTAKT / SERVICE-ADR oder HÄNDLER-
LISTE / HÄNDLERLISTE
13. Entsorgung
Elektrogeräte, die mit der durchgestrichenen
Mülltonne gekennzeichnet sind, zur Entsorgung nicht in den Hausmüll geben, sondern einem geeigneten Entsorgungssystem zuführen.
In Ländern der EU (Europäische Union) dürfen Elektrogeräte nicht durch den Haus- bzw. Restmüll entsorgt werden (WEEE - Waste of Electrical and Electronic Equipment, Richtlinie
2002/96/EG). Sie können Ihr Altgerät bei öffentlichen Sammelstellen Ihrer Gemeinde bzw. Ihres Wohnortes (z.B. Recyclinghöfe) abgeben. Das Gerät wird dort für Sie fachgerecht und kostenlos entsorgt.
Mit der Rückgabe Ihres Altgerätes leisten Sie einen wichtigen Beitrag zum Schutz der Umwelt!
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Seite 6/29
Operating Instructions - MULTIcharger LN-3008 EQU
1. Introduction
Congratulations on choosing the MULTIPLEX
MULTIcharger LN-3008 EQU, # 9 2540.
With the MULTIcharger LN-3008 EQU you own a high-performance 12 Volt battery charger which offers ultra-simple operation and unique features in this class, such as an integral EQUALIZER for balancing the individual cell voltages of LiXX batteries.
These are the essential feature of the
MULTIcharger LN-3008 EQU:
• Charges batteries containing 2 to 3S LiPo /
LiIo / LiFe cells and 4 to 8 NiMH / NiCd cells
• Integral EQUALIZER (with FlightPower /
Thunder Power-compatible connector system)
Æ MULTIPLEX Li-BATT BX batteries can be connected directly to the EQUALIZER port of the LN-3008 EQU. Separate adaptor sets are available for batteries with different connector systems: see
Chapter 8. - Accessories
• Ultra-simple to operate
We are sure that you will learn to appreciate your MULTIPLEX MULTIcharger LN-3008
EQU after a brief period of getting to know the machine; these Operating Instructions are intended to help you through this phase.
Yours - the MULTIPLEX Team
2. Specification
Input voltage
Battery types and cell count
Charge current
(charging power)
Trickle charge current
Weight
11 - 15 V
LiPo/LiIo/LiFe: 2 - 3S cells
NiMH/NiCd: 4 - 8 cells
0.1 - 3 A
(max. 30 W)
0 - 100 mA
Integral
EQUALIZER for 2 to 3S LiXX batteries
EQUALIZER compensating current
EQUALIZER matching accuracy max. 42 mA approx. 32.5 mV
Charge termination methods
Delta-Peak cut-off for
NiMH batteries (-3 mV / cell) and for
NiCd batteries (-5 mV / cell)
Constant current/constant voltage for LiXX batteries
Charge connectors Two 4 mm sockets
EQUALIZER connectors
Sockets for connection to a stabilised mains
PSU or a car battery
Dimensions
One MULTIPLEX /
FlightPower / Thunder
Power compatible socket
Two leads terminating in 4 mm banana plugs for direct connection to a mains PSU.
Crocodile clips with 4 mm sockets for connection to car battery also supplied approx. 120 x 80 x 25 mm approx. 170 g
2.1. The charger’s software functions
• Automatic cell count detection of the battery connected to the charger
• Charging of Lithium batteries with and without EQUALIZER function
• Charging of Nickel batteries
2.2. The charger’s safety functions
• Reverse polarity guard at input and output
• Protection from inadequate and excessive input voltage
• Integral safety timer
• Status indicator LEDs
• User input confirmation buzzer
• Integral buzzer and LEDs for error display
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 7/29
Operating Instructions - MULTIcharger LN-3008 EQU
3. Safety Notes
! These operating instructions are an in- tegral part of the product. They contain important information and safety notes, and should be kept in a safe place at all times. Be sure to pass them on to the new owner if you ever dispose of the product.
! Read the instructions carefully, and be sure to observe the safety notes.
Do not operate the charger until you have carefully read right through these operating instructions and the safety notes, which may be included in these instructions or supplied separately.
! Do not open the charger, and on no account carry out technical modifications of any kind. Use genuine accessories and replacement parts exclusively.
! If you are obliged to operate the charger in conjunction with other makes of equipment, it is up to you to ensure that they are of proper quality and work correctly. Every new or revised system must be checked carefully before it is used
“in anger”. Do not use the charger if anything appears not to be in order; first seek out the fault and eliminate it.
! Always observe the charging notes supplied by the battery manufacturer.
! Protect the charger from dust, damp, rain, heat and vibration.
! The charger may become hot when it is operating.
Take care when touching the hot surfaces!
The slots in the case are designed for cooling the charger, and must not be covered or obstructed. The unit must not be enclosed when operating, as this would prevent cooling air flowing round it. The charger should never be subjected to direct sunshine.
! When operating, the charger and the battery to be charged must be placed on a non-inflammable, heat-resistant surface, which is not electrically conductive. The charger, battery and charge lead must not be placed directly on the car’s bodywork.
Never operate the charger in the vicinity of highly inflammable materials.
! Never connect more than one battery to the charger’s charge sockets and
EQUALIZER port. Do not attempt to recharge multiple battery packs simultaneously.
! Always supervise your batteries when they are on charge. Never leave the charger connected to its power supply when you are not in the vicinity.
! Cells which are charged together as a battery must be of the same make, type and capacity.
! Always allow your batteries to cool down to ambient temperature before recharging them.
! When connecting the charger to the car battery or a stabilised mains PSU, take great care to connect it correctly. Never connect the unit with reversed polarity.
! Connecting leads and charge outputs must never be connected to each other.
Charge and connecting leads must not be left coiled up when the charger is in use.
! Disconnect the battery from the
MULTIcharger LN-3008 EQU immediately when the charge process is concluded.
4. General Charging Notes
• Always keep within the maximum stated permissible charge current for your battery.
• The charge lead used must consist of cable of generous cross-sectional area, and must not be longer than 30 cm. The resistance of leads which are too thin or too long may have an adverse effect on the charge process.
• Ensure that all electrical connections are firm and sound. There must be no danger of intermittent contact in the connections.
• Before you initiate the charge process check that the selected battery mode matches the battery type connected to the unit. Check also that the settings are correct for the type of battery in use.
• Never leave your batteries on charge unsupervised.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 8/29
Operating Instructions - MULTIcharger LN-3008 EQU
5. The charger
Fuse
Ventilation slots
Rotary currentsetting knob
Operating buttons
6. Using the MULTIcharger
EQUALIZER
Port
Charge sockets
LN-3008 EQU for the first time
When carrying out the following procedures be sure to observe the Safety Notes and the
General Charging Notes.
• Connect the MULTIcharger LN-3008 EQU to your car battery using the crocodile clips provided. Alternatively connect the unit to a stabilised mains PSU using the 4 mm banana plugs. The output voltage of the
PSU must be between 11 V and 15 V.
Maintain correct polarity: red = positive terminal, black = negative terminal. The charger is now in stand-by mode, and the
POWER LED glows.
• Connect the charge leads to the charger (Æ
NiXX/LiXX Charge), and then connect the battery to the charge lead. Maintain correct polarity: red = positive terminal, black = negative terminal.
• If you wish to charge a Lithium battery (LiPo,
LiIo or LiFe) consisting of 2S or 3S cells, you should also connect its balancer plug to the
EQUALIZER Port of the MULTIcharger LN-
3008. Remember to maintain correct polarity. Suitable adaptor sets for connecting
Lithium batteries with Graupner / robbe or
Polyquest balancer plugs are listed in
Chapter 8. – Accessories.
• How the integral EQUALIZER works: this function is used to compensate for voltage variations in the individual cells of your LiXX battery while it is being charged by the
MULTIcharger LN-3008 EQU. This ensures that all the cells of your battery will be at the same voltage when the charge process is complete.
• Example: charging a 3S LiPo battery without using the integral EQUALIZER:
Towards the end of the charge process the individual cell voltages are 4.0 V, 4.2 V and
4.4 V. This equates to a total voltage of 12.6
V, and the charger would terminate the charge process at this point.
In this example the 4.4 V cell would already be overcharged and damaged, whereas the
4.0 V cell would not yet be fully charged.
If you use the integral EQUALIZER of the
MULTIcharger LN-3008 EQU, the unit compensates for the voltage differences during the charge process, ensuring that all three cells reach the final charge voltage of
4.2 V at the same time, and are therefore perfectly charged.
• Press the BATT TYPE button to change the battery type; the currently set type is indicated by the appropriate LED.
• The MULTIcharger LN-3008 EQU is capable of charging the following battery types:
- Lithium-Polymer (LiPo) Æ 3.7 V / cell
- Lithium-Ionen (LiIo)
Æ 3.6 V / cell
- Lithium-Ferrit (LiFe)
Æ 3.3 V / cell
- Nickel-Metal-Hydride (NiMH)
- Nickel-Cadmium (NiCd) batteries
• The rotary knob marked CHARGE
CURRENT is used to select the appropriate charge current for your battery. Caution: take care not to alter the charge current accidentally while the battery is on
charge!
• Always charge your LiPo and LiIo
batteries at the 1C rate (C = capacity / hour). This means: if your battery has a capacity of 2100 mAh, charge it at 2.1 A.
LiFe batteries should be charged at a rate no higher than the charge current stated
by the manufacturer.
The charger charges the pack using the constant current / constant voltage method, but in any case terminates the charge process after a maximum of three hours
(Safety Timer).
• NiMH and NiCd batteries should also be charged at the 1C rate. However, the
MULTIcharger LN-3008 EQU should only be used to charge NiMH and NiCd batteries which are expressly marked as
fast charge capable. The charger
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 9/29
Operating Instructions - MULTIcharger LN-3008 EQU automatically terminates the charge process using the Delta-Peak cut-off method, but in any case after a maximum of one and a half hours (Safety Timer).
• Hold the START/STOP button pressed in to initiate the charge process. The unit now automatically detects the cell-count of your battery, and charges the pack. During the charge process the CHARGE LED and the
LED for the set battery type light up. If you have connected the Balancer socket of your
LiXX battery to the EQUALIZER Port, the
LED for the set LiXX battery type flashes to indicate that the EQUALIZE process is running simultaneously.
• As soon as the battery is fully charged, the unit automatically terminates the process and beeps repeatedly to warn you of this. At the same time the CHARGE END LED lights up.
• You must press the START/STOP button again before you charge the next battery; this action returns the charger to stand-by mode.
• You can interrupt the charge process at any time, i.e. before the battery is fully charged, by pressing the START/STOP button.
6.2. Equalizing Lithium batteries
This function is used to match the individual cell voltages of your LiXX battery without charging the pack at the same time.
• Connect your charge lead to the charger (Æ
NiXX/LiXX Charge), then connect your
Lithium battery to the charge lead. Take care to maintain correct polarity (red = positive terminal, black = negative terminal)!
• Always connect the Balancer socket of the
LiXX battery to the charger’s EQUALIZER
Port at the same time, again taking care over correct polarity.
• Select the desired Lithium battery type by pressing the BATT TYPE button; the associated LED lights up to indicate the currently set battery type.
• The position of the CHARGE CURRENT rotary knob has no effect during the
EQUALIZE process.
• A brief press on the START/ STOP button initiates the EQUALIZE process. During the
EQUALIZE process only the LED for the set
LiXX battery type flashes; the CHARGE LED remains off.
• As soon as the voltages of the individual cells of your LiXX battery are properly matched (balanced), the charger indicates this by emitting multiple beeps; at the same time the CHARGE END LED lights up.
• During the EQUALIZE process you can press the START/STOP button to interrupt the process before the balancing of the individual cell voltages is complete.
7. Error indicators
Errors are indicated by the charger beeping, and by the CHARGE and CHARGE END
LEDs flashing repeatedly.
Error type
LED flash rhythm
Input voltage below 11 V or above 15 V
1 x
No battery connected to the charger,
or error in the connection between charger and battery
2 x
Battery connected to the charger with reversed polarity
3 x
NiXX battery with fewer than 4 or more than 8 cells, or LiXX battery with fewer than 2S or more than 3S cells connected to the charger
The balancer connector of an LiXX battery was not connected to the
EQUALIZER PORT when the
EQUALIZE process was initiated
or the Balancer socket of an LiXX battery was disconnected from the
EQUALIZER Port during the charge or EQUALIZE process, or the balancer plug of a LiXX battery is connected to the EQUALIZER port, but the charger is currently in NiXX mode, or the voltage of one individual
LiXX battery cell is too low:
- LiPo packs: below 2.75 V per cell
- LiIo packs: below 2.75 V per cell;
- LiFe packs: below 2.00 V per cell;
Or too high:
- LiPo packs: above 4.30 V per cell
- LiIo packs: above 4.20 V per cell
- LiFe packs: above 3.90 V per cell
Problem within the charger, or the
Safety Timer has tripped (1.5 hours with NiXX batteries; 3 hours with LiXX batteries)
4 x
5 x
6 x
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 10/29
Operating Instructions - MULTIcharger LN-3008 EQU
8. Accessories
We guarantee our products in accordance with the currently valid statutory regulations. If
Tx charge lead (diode plug)
PROFI-CAR Tx charge lead
Tx battery direct charge lead
MP-RC Rx battery charge lead
UNI Rx battery charge lead
Charge lead for batteries with M6 socket
Polyquest adaptor set
Graupner / robbe adaptor set
# 8 6020
# 8 6022
# 8 6021
# 8 5106
# 8 5094
# 9 2516
9. CE Conformity Declaration
The device has been assessed and approved in accordance with European harmonised directives.
This means that you possess a product whose design and construction fulfil the protective aims of the European Community designed to ensure the safe operation of equipment.
If required, you can request MULTIPLEX to supply a copy of the unit’s Conformity
Declaration. Please contact the company using the contact details at the foot of the page.
MULTIPLEX Modellsport GmbH & Co. KG accepts no liability for loss, damage or costs which arise from the incorrect use and operation of the product, or are connected with such usage in any way.
Unless the law states otherwise, the liability on the part of MULTIPLEX to pay damages, regardless of the legal argument employed, is limited to the invoice value of those
MULTIPLEX products which were directly involved in the event in which the damage occurred. This does not apply if liability is incurred according to statutory law on account of intentional or gross negligence.
MULTIPLEX Modellsport GmbH & Co. KG does not guarantee that the documents supplied with the charger are complete and correct in every respect.
11. Guarantee
# 8 6001
# 8 6002 your initial course of action should be to contact the dealer from whom you purchased the equipment.
The guarantee does not cover faults and malfunctions which are caused by the following: reversed polarity
• The use of accessories other than genuine
MULTIPLEX items
Modifications or repairs which were not carried out by MULTIPLEX or by an authorised MULTIPLEX Service Centre
• Accidental or intentional damage
• Defects due to normal wear and tear
• Operation of the unit outside the limits stated in the Specification
12. Advice Service
We have taken great care to design these
Operating Instructions in such a way that you can quickly and easily find the answer to any question you may have. However, if you are still in any doubt, please contact your local model shop in the first instance, where you will usually find expert advice, freely given.
The addresses of our Service Centre partners can be found on our website: www.multiplex-rc.de at:
CONTACT / SERVICE PARTNERS or
DEALERS LIST / DEALERS LIST
13. Disposal
Electrical equipment marked with the cancelled waste bin symbol must not be discarded in the standard household waste; instead it should be taken to a suitable specialist disposal system.
In the countries of the EU (European
Union) electrical equipment must not be discarded via the normal domestic refuse system (WEEE - Waste of
Electrical and Electronic Equipment, Directive
2002/96/EG). You can take unwanted equipment to your nearest local authority waste collection point or recycling centre.
There the equipment will be disposed of correctly and at no cost to you.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 11/29
Operating Instructions - MULTIcharger LN-3008 EQU
By returning your unwanted equipment you can make an important contribution to the protection of the environment.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 12/29
Notice d’utilisation MULTIcharger LN-3008 EQU
1. Introduction
Nous vous remercions pour l’achat de notre chargeur MULTIPLEX MULTIcharger LN-
3008 EQU, # 9 2540.
Avec ce MULTIcharger LN-3008 EQU vous venez de faire l’acquisition d’un chargeur 12
Volt de haute qualité, d’une utilisation simple avec EQUALIZER, pour équilibrer la tension de chaque élément LiXX de l’accu.
Les caractéristiques principales du
MULTIcharger LN-3008 EQU sont les suivantes :
• Capable de charger les accus LiPo / LiIo /
LiFe de 2 à 3 éléments et les accus NiMH /
NiCd de 4 à 8 éléments.
• EQUALIZER intégré (avec prises compatibles Flight / Thunder Power)
Æ Les accus MULTIPLEX Li-BATT BX peuvent directement être branchés sue le port EQUALIZER du LN-3008 EQU – pour les accus avec d’autres prises, il existe des adaptateurs que l’on peut obtenir séparément, voir chapitre 8 - Accessoires
• Utilisation, on ne pleut plus simple
Nous sommes persuadés que votre chargeur
MULTIPLEX MULTIcharger LN-3008 EQU vous donnera entièrement satisfaction après une rapide prise en main, facilitée par la notice.
Votre Team- MULTIPLEX
Alimentation 11 - 15 V
Type d’accus et nombre d’élém.
Courant de charge
(Rendement)
Courant de la charge de maintien
LiPo/LiIo/LiFe: 2 - 3S élém.
NiMH/NiCd: 4 - 8 élém.
0,1 - 3 A
(max. 30 W)
0 - 100 mA
EQUALIZER intégré pour accus LiXX 2 à 3S
Courant d’équilibrage de l’EQUALIZER max. 42 mA
Précision d’équilibrage de l’EQUALIZER env. 32,5 mV
Prise de charge
Branchement
EQUALIZER
Prises pour branchement sur une batterie de voiture ou sur une alimentation stabilisée
Dimensions
Accus NiMH (-3 mV/élém.) et pour Accus NiCd
(-5 mV/élément)
Charge avec tension et intensité constante pour accus LiXX deux fiches de 4 mm
MULTIPLEX / FlightPower /
Thunder Power compatibles
Deux cordons de branchement avec fiches bananes de 4 mm pour branchement direct sur une alim. stabilisée. Pinces crocos. avec fiches de 4 mm pour le branchement sur une batterie de voiture, sont fournis avec le chargeur
120 x 80 x 25 mm
2.1. Fonctions du chargeur
• Reconnaissance automatique du nombre d’éléments de l’accu branché
• Charge des accus Lithium avec ou sans fonction d’ EQUALIZER
• Charge des accus Nickel
2.2. Fonctions de sécurité du chargeur
• Détrompeurs (pour éviter l’inversion de polarité) sur l’entré et la sortie
• Protection contre une tension d’alimentation trop élevée ou trop basse
• Safety Timer intégré
• LEDs pour afficher l’état
• Buzzer pour l’autorisation utilisateur
• Affichage d’erreurs par Buzzer et LEDs intégrés
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 13/29
joint).
Notice d’utilisation MULTIcharger LN-3008 EQU
! Cette notice fait partie intégrante du produit. Elle contient d’importantes informations et des conseils de sécurité.
Gardez-là à portée de main, car elle doit
être fournie avec le produit en cas de revente à un tiers.
! Lisez attentivement la notice!
Respectez les consignes de sécurité!
N’utilisez le chargeur qu’après avoir lu attentivement la notice et les différents conseils de sécurité (qui figurent dans la notice même ou sur un feuillet séparé
! Ne pas ouvrir le boîtier. Ne faites des modifications sous aucun prétexte.
N’utilisez que des accessoires originaux ou des pièces de rechanges originales.
! Si vous utilisez cet appareil avec d’autres éléments, de marque différente, assurez-vous de la qualité et de la compatibilité de ces derniers. Toute nouvelle configuration est à tester avant sa mise en service. Ne pas mettre l’appareil en fonction si vous remarquez une chose anormale. Recherchez l’erreur et solutionnez-la .
! Respectez les consignes de charge du fabricant de l’accu.
! Protégez le chargeur de la poussière, de l’humidité de la pluie, de la chaleur et des vibrations.
! En cours d’utilisation, le chargeur peut devenir très chaud.
Attention lorsque vous posez la main dessus !
Les fentes (ouvertures) sur le boîtier sont destinées au refroidissement. En aucun cas les recouvrir ou les boucher. Pour la charge, le chargeur doit être placé dans un endroit dégagé pour faciliter la circulation de l’air. Par ailleurs, évitez de le mettre en plein soleil.
! Pendant l’utilisation, le chargeur et l’accu doivent être placés sur une surface ignifugée, résistante à la température, et non conductrice. Ne jamais les mettre sur une carrosserie de voiture! . Ne pas se servir du chargeur à proximité de matériaux inflammables.
! Ne branchez qu’un seul accu à la fois au chargeur et sur le port EQUALIZER
N’essayez jamais de brancher et de charger plusieurs accus en même temps.
! Ne jamais laisser la charge de vos accus sans surveillance ainsi d’ailleurs que le chargeur lorsqu’il est branché à son alimentation!
! Ne chargez que des packs constitués d’éléments de même nature et de même capacité.
! Ne chargez vos accus que lorsque ceux-ci sont revenus à température ambiante.
! Lorsque vous branchez le chargeur à une batterie de voiture ou à une alimentation stabilisée, respectez la polarité, ne jamais inverser la polarité.
! Les cordons de branchement et les sorties chargeur ne doivent jamais être reliés entre eux. Durant la charge, les cordons ne doivent pas être enroulés.
! En fin de charge ou de décharge, débranchez l’accu de votre MULTIcharger
LN-3008 EQU.
charge
• Respectez l’intensité maximale de charge tolérée par votre accu.
• Le cordon de charge utilisé doit être de section suffisante et ne doit pas être plus long que 30 cm. Un cordon de charge trop fin et/ou trop long peut agir sur la charge de manière négative.
• Veillez à ce que les contacts se fassent correctement, à tous les niveaux, évitez le jeu ou les contacts aléatoires au niveau des branchements.
• Avant de lancer la procédure de charge, vérifiez si le programme de charge choisi est compatible avec votre accu et que tous les paramètres de réglages qui correspondent à votre accu ont été effectués.
• Ne laissez jamais votre accu en charge sans surveillance.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 14/29
Notice d’utilisation MULTIcharger LN-3008 EQU
Fusible
Bouton de réglage du courant
6.1.
Ouies de refroidissement
Touches de fonctions
MULTIcharger LN-3008 EQU
Charge des accus
Port
EQUALIZE
Prise de charge
• En effectuant les étapes ci-dessous,
respectez les Conseils de sécurité et les
Recommandations pour la charge.
• Branchez le MULTIcharger LN-3008 EQU sur la batterie de votre voiture avec les pinces crocos fournies. Vous pouvez
également brancher le chargeur sur une alimentation stabilisée avec une sortie de
11V à 15 V, en utilisant les fiches bananes de 4 mm. Attention à la polarité (rouge
= Plus, noir = Moins). Le chargeur est maintenant en mode Standby et la LED
POWER est allumée.
• Branchez le cordon de charge au chargeur
(
Æ NiXX/LiXX Charge), puis l’accu au cordon de charge. Attention à la polarité
(rouge = Plus, noir = Moins)!
• Si vous voulez charger un accu Lithium
(LiPo, LiFe ou LiIo), branchez également sa prise Balancer sur le EQUALIZER Port du
MULTIcharger LN-3008 EQU. Attention à la polarité ! Vous trouverez des adaptateurs correspondants à votre accu Lithium avec prises Balancer Graupner, Robbe ou
Polyquest au chapitre 8 – Accessoires
• Fonction de l’ EQUALIZER intégré:
Utilisez cette fonction pour équilibrer les différents éléments LiXX de votre pack d’accu lors de la charge avec le
MULTIcharger LN-3008 EQU. En fin de charge, vous serez sûrs que tous les
éléments de votre pack ont été chargés à la même tension..
• Exemple : Charge d’un accu LiPo 3S sans utilisation de l’ EQUALIZER intégré:
En fin de charge la tension des différents
éléments est de 4,0 V, 4,2 V et 4,4 V. Cela correspond à une tension totale de 12,6 V, tension qui interromprait la procédure de charge à ce moment là.
L’élément avec 4,4 V serait dans ce cas surchargé et endommagé, alors que celui avec 4,0 V ne serait pas encore complètement chargé.
En utilisant l’ EQUALIZER intégré du
MULTIcharger LN-3008 EQU la tension de chaque élément est équilibrée durant la charge. Il veille à ce que les trois éléments soient chargés à la même tension de 4,2 V , donc une charge optimale.
• En appuyant sur la touche BATT TYPE vous changez de type d’accu, et le type d’accu choisi est signalé par la LED correspondante.
• Le MULTIcharger LN-3008 EQU peut charger les accus suivants:
- Lithium-Polymère (LiPo)
Æ 3,7 V / élém.
- Lithium-Ion (LiIo) Æ 3,6 V / élém.
- Lithium-Ferrite (LiFe) Æ 3,3 V / élém.
- Nickel-Metal-Hydrid (NiMH)
- Nickel-Cadmium (NiCd)
• Avec le bouton de réglage CHARGE
CURRENT vous réglez la tension de charge de votre accu. Attention: Ne déréglez pas la tension de charge par inadvertance durant la charge!
• Ne chargez vos accus LiPo et Lilo qu‘à
1C (C=capacité/heure). Cela signifie qu’un accu d’une capacité de 2.100 mAh ne doit
être chargé qu’à 2,1 A! Ne chargez les accus LiFe qu’à l’intensité indiquée par le
fabricant.
Le chargeur interrompt la procédure de charge dès que l’accu est plein selon le principe de la tension/intensité constante ou au plus tard au bout de 3 heures (Safety
Timer).
• Avec le MULTIcharger LN-3008 EQU, ne chargez que des accus NiMH et NiCd à 1
C, capables d’absorber la charge rapide.
Le chargeur est équipé du système Delta-
Peak qui coupe automatiquement la charge lorsque l’accu est plein ou au plus tard au bout de 1h30 (Safety Timer).
• En appuyant plus longuement sur la touche
START/STOP vous lancez la procédure de charge. Le chargeur vous indique
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 15/29
Notice d’utilisation MULTIcharger LN-3008 EQU automatiquement le nombre d’éléments de votre pack et l’enregistre. Pendant la charge, la LED CHARGE et la LED du type d´accu choisi sont allumées. Si vous avez branché la fiche d´équilibrage de votre accu LiXXX sur le EQUALIZER Port, le chargeur montre le processus d´équilibrage simultané par le clignotement de la LED du type d´accu LiXX choisi.
• Dès que l’accu est chargé, la procédure de charge s’interrompt automatiquement et le chargeur signale cela par plusieurs Bips sonores et la LED CHARGE END s’allume.
• Avant de recharger le prochain accu, il faut ré appuyer sur la touche START/STOP.
Vous vous retrouvez ensuite de nouveau en mode Standby.
• Durant la charge, et avant que l’accu ne soit plein, vous pouvez interrompre la charge en appuyant sur la touche START/STOP.
Les erreurs sont signalées par des Bips sonores et par des clignotements des LEDs
CHARGE et CHARGE END.
Causes d’erreurs
Alimentation inférieure à
11 V ou supérieure à 15 V
Aucun accu branché au chargeur ou erreur dans la connexion entre chargeur et accu
L’accu est mal branché au chargeur, inversion de polarité
Clignotement LED
1 fois
2 fois
3 fois
6.2. Equilibrage des accus Lithium
Utilisez cette fonction pour équilibrer la tension de charge des éléments individuels de votre accu LiXX sans le charger.
• Branchez votre cordon de charge sur le chargeur ( Æ NiXX/LiXX Charge) et ensuite votre accu Lithium sur le cordon de charge.
Attention de ne pas inverser la polarité
(rouge = Plus, noir = Moins)!
• Branchez toujours en plus la fiche d´équilibrage de l´accu LiXX sur le
EQUALIZER Port du chargeur. Prenez toujours garde de ne pas inverser la polarité!
• Choisissez le type d´accu correct en appuyant sur la touche BATT TYPE, la LED correspondante montre le type d´accu choisi.
• La position du bouton de réglage CHARGE
CURRENT n´est pas importante pendant le processus d´équilibrage.
• Mettez en route le processus d´équilibrage en appuyant brièvement sur la touche
START/STOP. Pendant l´équilibrage, seule la LED du type d´accu choisi clignote. La
LED CHARGE est éteinte.
• Dès que la tension des éléments individuels de votre accu LiXX est équilibrée, le chargeur émet un signal sonore répété et la
LED CHARGE END s´allume.
• Vous pouvez interrompre l´équilibrage en appuyant sur la touche START/STOP avant la fin du processus d´équilibrage.
Accu NiXX Accu avec moins de 4
éléments ou plus de 8 ou accu LiXX avec moins de 2 éléments ou plus de
3 éléments branchés au chargeur
La prise Balancer de l'accu LiXX n'était pas branchée au EQUALIZER
Port lors du démarrage de la procédure d'équilibrage ou La fiche
équilibrage d´un accu LiXX a été retirée du EQUALIZER Port pendant le processus de charge/d´équilibrage
ou la prise Balancer de l’accu LiXX est branchée sur le EQUALIZER
Port mais le chargeur est en mode
NiXX ou la tension d’un des éléments de l’accu LiXX est trop basse:
- Accu LiPo : inf.à 2,75 V par élément
- Accu LiIo: inf.à 2,75 V par élément
- Accu LiFe: inf.à 2,00 V par élément ou trop élevée:
- Accu LiPo:sup.à 4,30 V par élément
- Accu LiIo: sup.à 4,20 V par élément
- Accu LiFe:sup.à 3,90 V par élément
Problème interne au chargeur ou
Dépassement du temps Safety Timer
(1,5 heures pour accu NiXX et 3 heures pour accus LiXX )
4 fois
5 fois
6 fois
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 16/29
Notice d’utilisation MULTIcharger LN-3008 EQU
8. Accessoires
Articles Référence.
Cordon de charge émetteur (fiche mâle)
# 8 6020
Cordon de charge émetteur
PROFI-CAR
Cordon de charge direct pour accu d’émission
Cordon de charge pour accu de réception MP-RC
# 8 6022
# 8 6021
# 8 5106
Cordon de charge pour accu de réception (UNI)
Cordon de charge pour accu avec prise M6
Adaptateurs Polyquest
Adaptateurs Graupner / robbe
# 8 5094
# 9 2516
# 8 6001
# 8 6002
9. Déclaration de conformité CE
Ce produit est conforme aux normes européennes.
Vous êtes en possession d’un produit, qui, de par sa conception, notamment des éléments de sécurité, correspond aux normes européennes, pour permettre une utilisation fiable de l’appareil.
En cas de nécessité, cette déclaration peut
être fournie par MULTIPLEX sur simple demande écrite à l’adresse en pied de page.
10. Exclusion de responsabilité
La société MULTIPLEX Modellsport GmbH &
Co.KG ne pourra pas être tenu responsable pour les éventuelles pertes, dégâts ou coûts, dus à une utilisation non conforme du produit.
L’obligation de dédommagement, quelqu’un soit le motif juridique, se limite au montant approximatif de la facture, dans la mesure ou celle-ci est légalement applicable. Ceci n’est pas applicable si la responsabilité est flagrante.
Par ailleurs, MULTIPLEX Modellsport GmbH
& Co.KG ne peut pas être tenu pour responsable quant au contenu et l’exactitude des documents fournis avec le chargeur.
11. Garantie
Nous accordons une garantie sur nos produits selon les conditions légales en vigueur à ce jour. En cas de problème, adressez-vous à votre détaillant qui vous a vendu le produit.
Sont exclus de la garantie, les dysfonctionnements dus à:: branchement, inversion de polarité
• Utilisation des composants ou accessoires autres que les originaux MULTIPLEX
• Modifications / Réparations, effectuées par un service non agrée MULTIPLEX
• Dégradation volontaire ou non
• Dysfonctionnement lié à une usure normale
• Utilisation en dehors des spécifications techniques
12. Assistance / Service
Nous nous sommes efforcés de faire cette notice de telle manière à ce que vous trouviez rapidement réponses à vos questions. Si toutefois vous deviez encore avoir des questions concernant ce chargeur, n’hésitez pas à contacter votre vendeur qui saura vous conseiller utilement.
Vous trouverez les adresses de nos partenaires sur notre site: www.multiplex-rc.de sous
CONTACTS / ADRESSES SAV ou POINTS
PILOTES / POINTS PILOTES
13. Recycling
Les appareils électriques qui sont marqués du sigle ci-contre (poubelle) doivent être recyclés par des organismes appropriés et ne doivent pas être mis avec les déchets ménagers.
Dans les pays de la communauté européenne, vous n’avez pas le droit de vous débarrasser de vos appareillages électriques et les jetant aux ordures ménagères (WEEE - Waste of
Electrical and Electronic Equipment, Directive
2002/96/EG). Vous pouvez déposer vos vieux appareils dans une collecte de votre commune par exemple, qui veillera à ce que ces appareils soient recyclés correctement.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 17/29
Notice d’utilisation MULTIcharger LN-3008 EQU
En amenant ces appareils dans ces centres, vous participez à la protection de l’environnement!
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Page 18/29
Instrucciones del MULTIcharger LN-3008 EQU
1. Introducción
Nos alegramos de que haya elegido nuestro
MULTIPLEX MULTIcharger LN-3008 EQU,
# 9 2540.
Con el MULTIcharger LN-3008 EQU, Usted posee un cargador de 12 V y de altas prestaciones, cuyo manejo es de lo más sencillo y que dispone de características
únicas en su clase, como el ECUALIZADOR integrado para igualar el voltaje de los elementos individuales que forman sus baterías de Litio.
Las características más notables del
MULTIcharger LN-3008 EQU son:
• Puede cargar baterías LiPo / LiIon / LiFe con 2 y 3 elementos en serie y baterías
NiMh / NiCad de entre 4 y 8 elementos.
• Equilibrador (ecualizador) integrado
(compatible con conectores FlightPower
/ Thunder Power)
Æ Las baterías MULTIPLEX Li-BATT BX pueden conectarse directamente al puerto de equilibrado del 3008 EQU – existen adaptadores para baterías con otros tipos de conectores, consulte el apartado 8. - Accesorios
• Manejo muy sencillo
Estamos convencidos de que, tras un breve aprendizaje, se habrá familiarizado con sus instrucciones y apreciará el cómodo manejo de su MULTIPLEX MULTIcharger LN-3008
EQU.
Su equipo MULTIPLEX
Voltaje de entrada 11 - 15 V
Tipos de baterías y número de elem.
Corriente de carga
(potencia de carga)
LiPo/LiFe/LiIo: 2 - 3S elem.
NiCad/NiMH: 4 - 8 elem.
0,1 - 3 A
(máx. 30 W)
Corriente de mantenimiento
EQUILIBRADOR integrado
Corriente del
EQUILIBRADOR
Exactitud de equilibrado
Sistema de corte
(finalización de procesos)
0 - 100 mA para baterías Litio de 2 o 3 elementos en serie máx. 42 mA aprox. 32,5 mV
Con. carga
Conexiones del equilibrador
Tomas para conectarlo a una batería de automóvil o fuente de alimentación estabilizada
Dimensiones
Desconexión por Delta-
Peak para baterías NiMH
(-3 mV/elem.) y NiCad (-5 mV/elem.). Carga con corriente y tensión constante para baterías
LiXX
Dos hembras de 4 mm.
Conector para sistemas
MULTIPLEX / FlightPower /
Thunder Power
Dos cables de conexión con conectores banana de 4 mm para su conexión directa a una fuente de alimentación.
Pinzas de cocodrilo con hembras de 4 mm para batería de coche, incluidas.
aprox. 120 x 80 x 25 mm
Peso aprox. 170 g
2.1. Funciones software del cargador
• Detección automática del número de elementos de la batería conectada.
• Carga y descarga de baterías Litio con y sin función de equilibrado.
• Carga de baterías de Níquel
2.2. Funciones de seguridad del cargador
• Entrada y salida protegidas contra inversión de polaridad
• Protección ante voltaje demasiado bajo o alto en la entrada.
• Contador de tiempo de seguridad
• Indicador de estado mediante LEDs
• Notificación mediante avisador acústico
• Indicación de mensajes de error vía LEDs y avisador acústico
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Página 19/29
Instrucciones del MULTIcharger LN-3008 EQU
3. Consejos de seguridad
! Estas instrucciones forman parte del producto. Contienen información muy importante y recomendaciones de seguridad. Téngalas siempre al alcance de la mano y entréguelas si vende el producto a un tercero.
! ¡Lea detenidamente el manual de instrucciones! ¡Respete los consejos de seguridad!
No ponga en funcionamiento el aparato antes de haber leído atentamente y asimilado este manual de instrucciones y las siguientes recomendaciones de seguridad (bien incluidas en el manual o en su caso como documento anexo).
! No abra el dispositivo. No haga modificaciones técnicas bajo ningún concepto. Utilice exclusivamente recambios y accesorios originales.
! En caso de usar este equipo con dispositivos de otros fabricantes, asegúrese de su compatibilidad y calidad.
Cada vez que modifique la configuración, deberá realizar una exhaustiva prueba de funcionamiento. Si observa alguna anomalía no lo ponga en funcionamiento.
Deberá encontrar el problema y solucionarlo.
! Siga las recomendaciones de carga del fabricante de las baterías.
! Proteja el cargador del polvo, humedad, lluvia, vibraciones o golpes.
! El cargador puede calentarse bastante durante el funcionamiento.
¡Tenga cuidado al tocarlo!
Las ranuras de la carcasa sirven para la ventilación del dispositivo y no deben bloquearse o taparse en ningún momento.
Use el cargador en una zona despejada para que el aire pueda circular sin problemas. Además, no debería exponer directamente el cargador a los rayos solares.
! Durante la carga, tanto la batería como el cargador deben estar colocados sobre una superficie no inflamable, ignífuga y no conductora de la electricidad. ¡Nunca deje el cargador, la batería o el cable de carga directamente sobre la carrocería del coche! Nunca utilice el cargador cerca de materiales inflamables o volátiles.
! Conecte una sola batería a la toma del cargador o a la del EQUALIZADOR. Nunca debe intentar cargar más de una batería al mismo tiempo.
! ¡Monitorice la batería en carga en todo momento y nunca deje el cargador conectado a la alimentación sin vigilancia!
! Cargue solo baterías compuestas por elementos del mismo tipo (composición química) y capacidad.
! Cargue las baterías solo cuando estas estén a temperatura ambiente (déjelas enfriar).
! Cuando conecte el cargador a la batería del coche o a una fuente de alimentación estabilizada, compruebe la polaridad.
Nunca invierta la polaridad.
! Nunca deben cortocircuitarse los cables de carga o conexión. Los cables de alimentación y de carga no deben estar enrollados durante el funcionamiento.
! Al terminar el proceso de carga debe desconectar, inmediatamente, la batería del MULTIcharger LN-3008 EQU.
4. Generalidades sobre la carga
• Respete la corriente máxima autorizada para sus baterías.
• El cable de carga debe tener una sección suficiente, dimensionada en exceso y no debe exceder los 30 cm. de longitud. Un cable demasiado delgado o largo puede influir negativamente en el proceso de carga debido a su resistencia.
• Compruebe que todas las uniones presentan unos contactos perfectos.
Ninguna conexión debe sufrir falsos contactos.
• Antes de comenzar la carga debe comprobar que la batería y el programa elegido son compatibles y que todos los ajustes necesarios para ese tipo de baterías han sido configurados en el cargador.
• Nunca cargue sus baterías sin monitorizar el proceso.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Página 20/29
Instrucciones del MULTIcharger LN-3008 EQU
Fusible
Configuración de corriente
Ranuras de ventilación
Teclas
6. Puesta en marcha del
Puerto de
EQUILIBRADO
Conector de carga
MULTIcharger LN-3008 EQU
• Llevando a cabo los siguientes pasos cumplirá con los consejos de seguridad y las generalidades sobre la carga.
• Conecte el MULTIcharger LN-3008 EQU a la batería del coche usando las pinzas de cocodrilo suministradas. Como alternativa puede conectar el cargador a una fuente de alimentación estabilizada (usando los conectores banana de 4 mm) con una tensión entre 11 y 15 V. Compruebe que la polaridad sea correcta (rojo = positivo, negro
= negativo). El cargador estará en modo
Stand By (reposo) y el led POWER encendido.
• Conecte el cable de carga al cargador (Æ
NiXX/LiXX Charge) y, después, la batería al cable. Compruebe la polaridad
( rojo = positivo, negro = negativo).
• Si desea cargar una batería de Litio (LiPo,
LiIon o Life) con 2 o 3 elementos en serie, conecte su cable de equilibrado al conector de equilibrado (EQUALIZER Port) del
MULTIcharger LN-3008 EQU. Compruebe que la polaridad sea correcta. (En el apartado 8 – Accesorios, encontrará los adaptadores apropiados para conectar sus baterías de Litio equipadas con conectores
Graupner / robbe o Polyquest).
• Función del EQUILIBRADOR:
Use esta función para permitir que el
MULTIcharger LN-3008 EQU iguale la diferencia de voltaje entre los elementos individuales que componen su batería de
Litio. De esta manera tendrá la seguridad de que al terminar el proceso de carga los elementos individuales tendrán el mismo voltaje.
• Ejemplo: Carga de una LiPo 3S sin utilizar el EQUILIBRADOR incorporado:
Al terminar el proceso de carga el voltaje de los elementos podría ser de 4,0, 4,2 y 4,4V.
En total sumarían un voltaje de 12,6 V, haciendo que el cargador finalice la carga.
El elemento con 4,4 voltios estaría, en el ejemplo, sobrecargado y posiblemente estropeado, mientras que el elemento con
4,0 V no estaría cargado por completo.
Utilizando el EQUILIBRADOR integrado en el MULTIcharger LN-3008 EQU se igualará esta diferencia de voltaje mientras que se carga la batería. Para ello, el equilibrador se encargará de que todos los elementos tengan una tensión de 4,2 V al terminar la carga, consiguiendo una carga óptima.
• Pulsando la tecla BATT TYPE cambiará el tipo de batería, el tipo en uso actualmente se indica mediante el LED correspondiente.
• El MULTIcharger LN-3008 EQU puede cargar los siguientes tipos de batería:
- Polímeros de Litio(LiPo) Æ 3,7 V / elem.
- Iones de Litio (LiIo)
Æ 3,6 V / elem.
- Litio Hierro (LiFe)
Æ 3,3 V / elem.
- Níquel-Metal-Hidruro (NiMH)
- Níquel-Cadmio (NiCd)
• Con el potenciómetro CHARGE CURRENT podrá ajustar la corriente de carga de su batería. Precaución: ¡Tenga cuidado de no modificar la corriente durante la carga!
• Por regla general, cargue sus baterías
LiPo y Li-Ion a 1 C ( C= Capacidad / hora).
¡Por ejemplo, una batería de 2.100 mAh debe cargarse a 2,1 A aprox.! Las baterías
LiFe deben cargarse a la corriente máxima estipulada por el fabricante.
El dispositivo llevará a cabo la carga usando corriente y tensión constantes, finalizando este proceso en un plazo máximo de 3 horas (Intervalo de seguridad).
• Cargue sus baterías NiMh y NiCad siempre a 1C. Cargue con su
MULTIcharger LN-3008 EQU exclusivamente las baterías que estén identificadas como baterías NiMh o
NiCad capaces de soportar cargas
rápidas. El cargador dará por finalizado el proceso de carga al detectar el Delta-Peak o
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Página 21/29
Instrucciones del MULTIcharger LN-3008 EQU tras haber transcurrido 1,5 horas (Intervalo de seguridad).
• El proceso de carga comenzará si mantiene pulsada la tecla START/STOP. El cargador detectará automáticamente el número de elementos y cargará su batería. Durante el proceso de carga, el LED CHARGE y el
LED del tipo de batería seleccionada se encenderán. Si ha conectado el cable de equilibrado de su batería LiXX al puerto del
ECUALIZADOR, el cargador le indicará el proceso simultáneo de equilibrado haciendo parpadear el led del tipo de batería LiXX seleccionado.
• Tan pronto como la batería esté cargada, el cargador terminará el proceso de carga automáticamente y lo notificará emitiendo varios pitidos e iluminando el led CHARGE
END.
• Antes de cargar la siguiente batería, deberá pulsar de nuevo la tecla START/STOP. Una vez hecho, volverá a estar en el modo de
Stand By (reposo).
• Para interrumpir el proceso de carga antes de que su batería esté cargada, puede pulsar la tecla START/STOP.
6.2. Equilibrado de baterías de Litio
Utilice esta función para equilibrar el voltaje de individual de los elementos de su batería de Litio sin cargar la batería.
• Una el cable de carga al cargador (Æ
NiXX/LiXX Charge) y, después, la batería de Litio con el cable. Compruebe la polaridad ( rojo = positivo, negro = negativo).
• Además, deberá unir la conexión de equilibrado de su batería LiXX con el puerto
de equilibrado del cargador. ¡Compruebe que la polaridad sea correcta!
• Seleccione el tipo de batería deseado pulsando la tecla BATT TYPE , el tipo configurado actualmente se indica mediante el LED correspondiente.
• La posición del interruptor giratorio
CHARGE CURRENT no es significativa durante el proceso de EQUILIBRADO.
• El proceso de equilibrado comenzará si pulsa brevemente la tecla START/STOP.
Durante el proceso de equilibrado solo parpadeará el LED del tipo de batería LiXX que haya seleccionado. El led CHARGE se quedará apagado.
• Tan pronto como el voltaje de los elementos de su batería LiXX se hayan igualado, el cargador se lo hará saber emitiendo múltiples pitidos y encendiendo el led
CHARGE END.
• Si quiere interrumpir el proceso de equilibrado antes de que el voltaje de los elementos de su batería hayan sido igualados, puede hacerlo pulsando la tecla
START/STOP.
Los errores se indican mediante pitidos y destellos: leds CHARGE y CHARGE END.
Causa del error
Tensión de entrada inferior a 11 V o superior a 15 V.
No hay batería conectada al cargador o fallo en la conexión entre el cargador y la batería
Batería conectada al cargador con la polaridad invertida
Se ha conectado al cargador una batería NiXX con menos de 4 o más de 8 elementos o una batería LiXX con menos de 2 o más de 3 elementos.
La conexión de equilibrado de una batería LiXX no estaba conectada al
puerto de equilibrado al comenzar un proceso para equilibrarla o el conector de equilibrado de una batería
LiXX se ha desconectado durante el proceso de equilibrado del puerto de
equilibrado del cargador, o al utilizarse el puerto de equilibrado de su cargador
éste se encuentra en modo NiXX, o el voltaje de un elemento Litio es demasiado bajo.
- Bat. LiPo: menos de 2,75 V / elem.
- Bat. LiIo: menos de 2,75 V / elem.
- Bat. LiFe: menos de 2,00 V / elem. o muy alta:
- Bat. LiPo: más de 4,30 V / elem.
- Bat. LiIo: más de 4,20 V / elem.
- Bat LiFe: más de 3,90 V / elem.
Problema interno del cargador o se ha sobrepasado el tiempo de seguridad (1,5 horas para NiXX y 3 horas para LiXX).
8. Accesorios
Artículo
Cable de carga para emisoras
(Con diodo)
Cable de carga PROFI CAR
Parpade o de los leds
1 vez
2 veces
3 veces
4 veces
5 veces
6 veces
Referen- cia:
# 8 6020
# 8 6022
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Página 22/29
Instrucciones del MULTIcharger LN-3008 EQU
Cable de carga directa para baterías de emisora
Cable de carga para baterías de receptor MP-RC
Cable de carga para baterías de receptor (UNI)
Cable de carga para baterías con conectores M6
Adaptador Polyquest
Adaptador Graupner / robbe responsabilidad. que forman parte del cargador
# 8 6021
# 8 5106
# 8 5094
# 9 2516
# 8 6001
# 8 6002
9. Declaración de conformidad CE
El dispositivo ha sido probado según las directivas armonizadas de la Unión
Europea:
Por tanto, posee un producto que ha sido diseñado para cumplir con las regulaciones respecto la operatoria segura de dispositivos de la Unión Europea.
Puede solicitar la declaración de conformidad del dispositivo solicitándola a MULTIPLEX, utilizando los datos que aparecen en el pié de página para contactar.
10. Exclusión de responsabilidad
La empresa MULTIPLEX Modelltechnik
GmbH & Co. KG no se responsabiliza de pérdidas, daños o costes ocasionados por un uso incorrecto y/o manejo del producto, ya sea de manera directa o indirecta.
La responsabilidad sobre los daños causados, por cualquier motivo, queda limitada al valor de compra del producto
MULTIPLEX involucrado en el suceso, según la legislación actual. Quedan excluidos de este supuesto, los casos en los que se demuestre negligencia o falta de
La empresa MULTIPLEX Modellsport GmbH
& Co. KG no se responsabiliza de la integridad y exactitud de los componentes
11. Garantía
Aplicamos para nuestros productos la garantía legalmente establecida en cada momento. En caso necesario, diríjase al distribuidor autorizado donde haya comprado el producto para reclamar la garantía.
La garantía no cubrirá los posibles desperfectos o fallos ocasionados por:
• Manejo inadecuado, conexiones erróneas o inversión de polaridad.
• Uso de accesorios no originales de
MULTIPLEX,
• Modificaciones o reparaciones no llevadas a cabo por MULTIPLEX o un servicio técnico
MULTIPLEX, ,
• Daños ocasionados por el usuario con y sin intención de causarlos
• Desgaste por el uso
• Funcionamiento fuera de los márgenes técnicos especificados
12. Asesoramiento / Servicio
Nos hemos esforzado mucho a la hora de confeccionar estas instrucciones para que cada pregunta que se haga encuentre una pronta respuesta. Si a pesar de ello, sigue teniendo alguna pregunta sobre su nuevo cargador, por favor, consulte a su distribuidor que le atenderá gustosamente.
Encontrará las direcciones de nuestros puntos de Servicio Técnico en nuestro sitio
Web: www.multiplex-rc.de bajo
CONTACTO / DIRECCION SERVICIO o
PUNTOS DE VENTA / PUNTOS DE VENTA
13. Reciclado
Los dispositivos electrónicos señalizados con una papelera bajo una cruz, no deben ser arrojados a la basura normal, sino que se han de depositar en un contenedor para su reciclaje.
En los países de la UE (Unión
Europea) los dispositivos eléctricoselectrónicos no deben ser eliminados arrojándolos en el cubo de la basura doméstica. (WEEE Es el acrónimo de
Reciclado de equipos eléctricos y electrónicos en inglés. Directiva CE/96/2002). Seguro que dispone en su comunidad, o en su población, de un punto de reciclado donde depositar estos dispositivos cuando no le sean útiles.
Todos los dispositivos serán recogidos gratuitamente y reciclados o eliminados de manera acorde a la normativa.
¡Con la entrega para el reciclado de sus antiguos aparatos, contribuirá enormemente al cuidado del medio ambiente!
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Página 23/29
Istruzioni d’uso MULTIcharger LN-3008 EQU
1. Introduzione
Grazie per aver dato la preferenza al nostro caricabatterie MULTIPLEX MULTIcharger
LN-3008 EQU, # 9 2540.
Il MULTIcharger LN-3008 EQU è un caricabatterie a 12 Volt, ad alte prestazioni, facile da usare e con caratteristiche uniche per questa categoria. Il MULTIcharger LN-
3008 EQU dispone inoltre di un equalizzatore integrato che permette di bilanciare le tensioni dei singoli elementi dei pacchi batteria LiXX.
Le caratteristiche più importanti del
MULTIcharger LN-3008 EQU sono:
• Possibilità di caricare pacchi batteria LiPo /
LiIo / LiFe con 2 fino a 3 elementi (in serie) o pacchi batteria NiMH / NiCd con 4 fino a 8 elementi
• EQUALIZZATORE integrato (con connettore compatibile FlightPower /
Thunder Power)
Æ i pacchi batteria MULTIPLEX Li-BATT
BX possono essere collegati direttamente alla porta EQUALIZER del LN-3008 EQU – per pacchi batteria, con altri sistemi di connessione, sono disponibili a parte gli adattatori dedicati vedi capitolo 8.
Accessori
• Facile utilizzo
Siamo certi, che dopo un breve apprendimento, con l’aiuto delle presenti istruzioni, riuscirà a sfruttare fino in fondo tutte le potenzialità del MULTIPLEX
MULTIcharger LN-3008 EQU, per il massimo divertimento nel modellismo.
Il suo team MULTIPLEX
2. Dati tecnici
Alimentazione 11 - 15 V
Tipo pacchi batterie e numero elementi
Corrente di carica
(potenza di carica)
Corrente carica mantenimento
EQUALIZZATORE integrato
Corrente di bilanciamento dell’
EQUALIZZATORE
Precisione di bilanciamento dell’
EQUALIZZATORE
Rilevamento fine carica
LiPo/LiIo/LiFe:2-3S elementi
NiMH/NiCd: 4 - 8 elementi
0,1 - 3 A
(max. 30 W)
0 - 100 mA per pacchi batteria LiXX con
2 fino a 3 elementi (in serie) max. 42 mA ca. 32,5 mV
Delta-Peak per pacchi batteria NiMH (-3 mV/elemento) e per pacchi batteria NiCd
(-5 mV/elemento)
Carica con corrente / tensione costante per pacchi batteria LiXX
Connettori di carica due prese da 4 mm
Connettore un connettore compatibile
EQUALIZZATORE MULTIPLEX / FlightPower /
Thunder Power
Connettori per il collegamento ad un alimentatore stabilizzato o alla batteria autovettura due cavi di collegamento con spine a banana 4 mm per il collegamento diretto ad un alimentatore. Pinze a coccodrillo con prese 4 mm per il collegamento alla batteria dell’autovettura
Dimensioni ca. 120 x 80 x 25 mm
2.1. Funzioni Software del caricabatterie
• Riconoscimento automatico del numero di elementi del pacco batteria collegato
• Carica di pacchi batteria al litio, con o senza funzione EQUALIZZATORE
• Carica di pacchi batteria al nichel
2.2. Funzioni di sicurezza del caricabat.
• Protezione inversione di polarità in entrata e uscita
• Protezione da tensione d’alimentazione troppo bassa/elevata
• Temporizzatore di sicurezza
• Indicazione di stato tramite LED
• Segnale acustico per conferma impostazioni
• Indicazione errori tramite segnale acustico e
LED
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 24/29
Istruzioni d’uso MULTIcharger LN-3008 EQU
3. Avvertenze
! Queste istruzioni sono parte integrante del prodotto e contengono informazioni importanti. Per questo motivo è indispensabile conservarle con cura. In caso di vendita del prodotto, consegnarle all’acquirente.
! Leggere attentamente le istruzioni!
Rispettare le avvertenze!
Prima di mettere in funzione l’apparecchio, leggere attentamente le presenti istruzioni d’uso e le seguenti avvertenze (e/o le avvertenze allegate a parte al prodotto).
! Non aprire l’apparecchio. In nessun caso apportare modifiche tecniche. Usare esclusivamente accessori e parti di ricambio originali.
! Se l’apparecchio viene usato con prodotti di altri produttori, controllare la qualità e la compatibilità con il caricabatterie. Prima di mettere in funzione, controllare in ogni caso il corretto funzionamento dell’apparecchio.
Non mettere in funzione, se non si è certi della compatibilità dei componenti. Prima di mettere in funzione, cercare e risolvere eventuali problemi.
! Rispettare le indicazioni di carica caso tentare di caricare contemporaneamente più pacchi batteria.
! Non lasciare incustodito il caricabatterie durante il suo funzionamento. Il caricabatterie deve essere tenuto sotto controllo fino a quando è collegato all’alimentazione!
! Caricare solo elementi dello stesso tipo e della stessa capacità, uniti in un pacco batteria.
! Non caricare pacchi batteria ancora caldi. Attendere che si raffreddino a temperatura ambiente.
! Collegando il caricabatterie alla batteria dell’autovettura o ad un alimentatore stabilizzato, controllare la corretta polarità della connessione. Non collegare con polarità invertita.
! In nessun caso collegare i cavi dell’alimentazione alle prese di carica del caricabatterie. Durante il funzionamento è importante che i cavi dell’alimentazione e quelli di carica non siano aggomitolati.
! A carica ultimata, scollegare il pacco batteria dal MULTIcharger LN-3008 EQU. allegate al pacco batterie.
! Proteggere il caricabatterie dalla polvere, umidità, pioggia, calore e vibrazioni.
! Durante il funzionamento, il caricabatterie può diventare molto caldo.
Fare attenzione quando si tocca il caricabatterie!
Le fessure sulla scatola del caricabatterie sono indispensabili per consentire un raffreddamento ottimale. Non coprire le fessure, non ostacolare il ricircolo d’aria attorno all’apparecchio. Non posizionare l’apparecchio sotto il sole.
! Durante il funzionamento, posizionare il caricabatterie ed il pacco batteria da caricare su una superficie ignifuga, resistente al calore e isolata (in nessun caso posizionare sulla carrozzeria dell’autovettura!). Non mettere in funzione, se nelle vicinanze si trovano materiali facilmente infiammabili.
! Collegare sempre un solo pacco
• Non superare la corrente di carica massima consentita per il pacco batteria.
• Il cavetto di carica utilizzato deve avere un diametro adeguato ed una lunghezza massima di 30 cm. L’elevata resistenza interna di un cavetto di carica troppo sottile e/o lungo può influenzare negativamente il processo di carica.
• Controllare tutte le connessioni.
• Prima di avviare il processo di carica, controllare che il pacco batteria e la modalità di carica corrispondano. Controllare l’esattezza delle impostazioni sul caricabatterie.
• Non lasciare incustodito il pacco batteria durante il processo di carica. batteria alla presa di carica e alla porta
EQUALIZER del caricabatterie. In nessun
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 25/29
Istruzioni d’uso MULTIcharger LN-3008 EQU
Fusibile
Potenziometro per impostare la corrente
Fessure di raffreddamento
Tasti impostazion
6. Messa in funzione del
6.1.
MULTIcharger LN-3008 EQU
Caricare i pacchi batteria
Porta
EQUALIZER
Prese di carica
• Rispettare assolutamente quanto riportato nelle avvertenze e nelle informazioni
generali riguardanti la carica.
• Collegare il MULTIcharger LN-3008 EQU, con le pinze a coccodrillo, alla batteria dell’autovettura. In alternativa, il caricabatterie può essere collegato (con i connettori a banana 4 mm) ad un alimentatore stabilizzato, con una tensione in uscita da 11 V fino a 15 V. Controllare la polarità (rosso = polo positivo, nero = polo negativo). Il LED POWER si accende.
Adesso il caricabatterie si trova in modalità
Standby.
• Collegare il cavetto di carica, prima al caricabatteria (
Æ NiXX/LiXX Charge), poi al pacco batteria da caricare. Controllare la polarità (rosso = polo positivo, nero = polo negativo)!
• Se si vuole caricare un pacco batteria al litio
(LiPo, LiIo o LiFe) con 2 o 3 elementi (in serie), collegare anche il connettore di equalizzazione alla EQUALIZER Port del
MULTIcharger LN-3008 EQU. Controllare che la polarità sia corretta. (I cavi adattatori, necessari per collegare pacchi batteria al litio Graupner / robbe o Polyquest alla porta
EQUALIZER, sono disponibili a parte (vedi capitolo 8. – Accessori).
• Funzionamento dell’ EQUALIZZATORE integrato:
L’equalizzatore integrato MULTIcharger LN-
3008 EQU permette di bilanciare le tensioni dei singoli elementi dei pacchi batteria al
LiXX. A fine carica tutti gli elementi del pacco batteria avranno la stessa tensione.
• Esempio: caricare un pacco batteria LiPo con 3 elementi (in serie) senza usare l’
EQUALIZZATORE integrato:
Verso la fine del processo di carica le tensioni dei singoli elementi sono 4,0 V, 4,2
V e 4,4 V. La tensione totale del pacco batteria è quindi 12,6 V - il caricabatterie termina il processo di carica.
L’elemento con 4,4 V, riportato nell’esempio, sarebbe in questo caso già sovraccaricato e quindi danneggiato, mentre l’elemento con
4,0 V non sarebbe ancora completamente carico.
Usando l’ EQUALIZZATORE integrato del
MULTIcharger LN-3008 EQU le tensioni dei singoli elementi vengono bilanciate già durante il processo di carica. A fine carica ogni elemento avrà una tensione di 4,2 V – il pacco batteria adesso è stato caricato in modo ottimale.
• Con la pressione del tasto BATT TYPE è possibile scegliere il tipo di pacco batteria. Il tipo di pacco batteria attualmente impostato viene indicato con il LED corrispondente.
• Con il MULTIcharger LN-3008 EQU si possono caricare i seguenti pacchi batteria:
- Litio-Polimeri (LiPo) Æ 3,7 V / elem.
- Litio-Ioni (LiIo) Æ 3,6 V / elem.
- Litio-Ferrite (LiFe) Æ 3,3 V / elem.
- Nichel-Metal-Hydrid (NiMH)
- Nichel-Cadmio (NiCd)
• Con il potenziometro CHARGE CURRENT impostare la corrente di carica. Fare atten- zione a non spostare inavvertitamente il potenziometro di regolazione durante il
processo di carica!
• Caricare i pacchi batteria LiPo e LiIo
sempre con 1C (C= capacità / ora). P.es. caricare un pacco batteria con una capacità di 2.100 mAh con ca. 2,1 A! Caricare i pacchi batteria LiFe facendo attenzione a non superare la corrente di carica
consigliata dal produttore.
Il caricabatteria effettua la carica con il procedimento con corrente e tensione costanti, e termina il processo di carica al più tardi dopo 3 ore (Safety Timer).
• Caricare i pacchi batteria NiMH e NiCd anche con 1C. Con il MULTIcharger LN-
3008 EQU caricare esclusivamente pacchi batteria NiMh e NiCd che
permettono la carica veloce. Il
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 26/29
Istruzioni d’uso MULTIcharger LN-3008 EQU caricabatterie termina automaticamente il processo di carica con il rilevamento di fine carica Delta-Peak, e comunque al più tardi dopo 1,5 ore (Safety Timer).
• Con la pressione lunga del tasto
START/STOP si avvia il processo di carica.
Adesso il caricabatterie rileva automaticamente il numero di elementi del pacco batteria collegato ed inizia con il processo di carica. Durante il processo di carica rimangono accesi il LED CHARGE ed il LED del tipo batteria attualmente scelto.
Se alla EQUALIZER Port è collegato un connettore di bilanciamento di un pacco batteria LiXX, il caricabatterie segnala il processo di bilanciamento con il lampeggio del LED corrispondente al pacco batteria
LiXX impostato..
• Quando il pacco batteria è carico, il caricabatterie interrompe automaticamente il processo di carica – il caricabatterie emette un segnale acustico multiplo, il LED
CHARGE END si accende.
• Prima di caricare un nuovo pacco batteria, premere nuovamente il tasto START/STOP- il caricabatterie passa alla modalità Standby.
• La pressione del tasto START/STOP, durante il processo di carica, arresta anticipatamente il processo di carica in corso.
LED del tipo batteria LiXX impostato. Il LED
CHARGE non si accende.
6.2. Bilanciare i pacchi batteria al litio
Utilizzare questa funzione per bilanciare le tensioni dei singoli elementi di un pacco batteria LiXX, senza effettuare la carica.
• Collegare il cavo di carica al caricabatterie
( Æ NiXX/LiXX Charge), poi collegare il pacco batteria al litio. Rispettare la polarità
(rosso = polo positivo, nero = polo negativo)!
• Collegare infine il connettore di bilanciamento, del pacco batteria LiXX, alla
EQUALIZER Port del caricabatterie.
Controllare assolutamente che la polarità sia corretta!
• Premere il tasto BATT TYPE, per impostare il tipo di pacco batteria al litio. Il LED indica il tipo batteria attualmente impostato.
• La posizione del potenziometro CHARGE
CURRENT è indifferente per il processo di bilanciamento.
• Premere brevemente il tasto START/STOP per avviare il processo di bilanciamento.
Durante il bilanciamento lampeggia solo il
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 27/29
• Una volta terminato il bilanciamento delle tensioni degli elementi LiXX, il caricabatterie emette un segnale acustico multiplo ed il
LED CHARGE END si accende.
• Il processo di bilanciamento può essere interrotto in qualsiasi momento, premendo semplicemente il tasto START/STOP.
Gli errori vengono indicati con un segnale acustico e con il lampeggio multiplo dei LED
CHARGE e CHARGE END.
Errore
Istruzioni d’uso MULTIcharger LN-3008 EQU
Alimentazione inferiore a 11 V
o superiore a 15 V
Nessun pacco batteria collegato al caricabatterie o errore nella connessione fra caricabatterie e pacco batteria
Pacco batteria collegato al caricabatterie con polarità invertita
Lamp.
LED
1 volta
2 volte
3 volte
Pacco batteria NiXX con meno di 4 o più di 8 elementi o pacco batteria LiXX con meno di 2 o più di 3 elementi (in serie) collegato al caricabatterie
4 volte
Il connettore di bilanciamento di un pacco batteria LiXX non era collegato alla
EQUALIZER Port all'avvio del processo di EQUALIZZAZIONE o il connettore di un pacco batteria LiXX è stato scollegato dalla EQUALIZER Port mentre era in corso il processo di carica/bilanciamento
o connettore di bilanciamento di un pacco batteria LiXX collegato alla porta
EQUALIZER con caricabatterie in modalità NiXX o tensione di un elemento del pacco batteria LiXX troppo bassa:
5 volte
- Batt. LiPo: inferiore a 2,75 V per el.
- Batt. LiIo: inferiore a 2,75 V per el.
- Batt: LiFe: inferiore a 2,00 V per el. oppure troppo alta:
- Batt. LiPo: superiore a 4,30 V per el.
- Batt. LiIo: superiore a 4,20 V per el.
- Batt. LiFe: superiore a 3,90 V per el.
Problema interno del caricabatterie o superamento del tempo massimo di carica (1,5 ore per pacchi batteria NiXX e
3 ore per pacchi batteria LiXX)
6 volte
8. Accessori
Articolo Art.nr.
Cavetto di carica per radio (spina a diodi)
Cavetto di carica PROFI-CAR
9. Dichiarazione di conformità CE
La valutazione degli apparecchi avviene secondo le normative europee.
Lei è quindi in possesso di un apparecchio che rispetta i requisiti di costruzione e sicurezza stabiliti dall’Unione Europea.
La dichiarazione di conformità per l’apparecchio può essere richiesta alla
MULTIPLEX all’indirizzo riportato a fondo pagina.
10. Responsabilità
La MULTIPLEX Modellsport GmbH & Co.KG declina qualunque responsabilità per danni diretti o indiretti o costi dovuti ad un utilizzo improprio o erroneo di questo apparecchio.
Se stabilito dalla legge vigente, noi ci impegniamo solo al risarcimento del danno per un importo non superiore al valore dei prodotti MULTIPLEX coinvolti nell’evento.
Questo non vale, se dal punto di vista giuridico siamo tenuti a rispondere dei danni per colpa grave o comportamento doloso.
Inoltre la MULTIPLEX Modellsport GmbH &
Co.KG non garantisce la correttezza e la completezza delle informazioni e delle istruzioni allegate al caricabatterie.
# 8 6020
# 8 6022
Cavetto carica diretto per batt. Tx # 8 6021
Cavetto di carica batt. Rx MP-RC # 8 5106
Cavetto di carica batt. Rx (UNI) # 8 5094
Cavetto di carica per pacchi batteria con connettore M6
# 9 2516
Set adattatore Polyquest # 8 6001
Set adattatore Graupner / robbe # 8 6002
11. Garanzia
I nostri prodotti sono coperti da garanzia, come stabilito dalle leggi vigenti. Nel caso si renda necessaria una riparazione in garanzia, il caricabatterie può essere consegnato al rivenditore, presso il quale l’apparecchio è stato acquistato
La garanzia non copre i difetti dovuti a:
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 28/29
Istruzioni d’uso MULTIcharger LN-3008 EQU
• uso improprio dell’apparecchio, collegamenti errati o con polarità invertita
• utilizzo di accessori non originali
MULTIPLEX
• modifiche / riparazioni non eseguite dalla
MULTIPLEX o da un centro assistenza autorizzato MULTIPLEX
• danneggiamento involontario/volontario
• difetti dovuti a normale usura
• funzionamento aldifuori delle specifiche tecniche
12. Assistenza
Con le presenti istruzioni abbiamo cercato di dare una risposta veloce e semplice a tutte le domande che potrebbero sorgere durante l’utilizzo del caricabatterie. Se nonostante ciò dovesse avere bisogno di altre informazioni o supporto tecnico, non esiti a contattare il suo rivenditore.
Gli indirizzi dei nostri centri di assistenza sono elencati sul nostro sito: www.multiplex-rc.de cliccando su:
CONTATTI / INDIRIZZO DI SERVIZIO o
LISTA NEGOZI / LISTA NEGOZI
13. Smaltimento
Apparecchi elettrici, contrassegnati con il bidone della spazzatura depennato, non possono essere smaltiti nella normale spazzatura di casa, ma devono essere riciclati opportunamente.
Nei paesi UE (Unione Europea) gli apparecchi elettrici non possono essere smaltiti nella spazzatura domestica (WEEE - Waste of Electrical and Electronic Equipment, normativa
2002/96/EG). I vecchi apparecchi possono essere portati ai punti di raccolta del comune o di zona (p.es. centri di riciclaggio), dove l’apparecchio verrà smaltito in modo idoneo e gratuito.
Lo smaltimento adeguato dei vecchi apparecchi elettrici aiuta a salvaguardare l’ambiente!
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de Pagina 29/29
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project