Professional dual cd player
.
Professional dual cd player
PROFESSIONAL CD PLAYER WITH ANTI-SHOCK MEMORY
USER MANUAL
IMPORTANT
Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CD Player function :
1. POWER BUTTON
Press the power switch to turn the unit on. To switch the POWER off press the POWER switch
again.
2. JOG & SHUTTLE WHEELS
Shuttle : Use the dial to select the scanning direction and speed. The disc is scanned in the
forward direction when the shuttle dial is turned clockwise from the neutral position, in the reverse
direction when the shuttle dial is turned counterclockwise. The scanning speeds up when the
shuttle dial is turned faster.
Jog : In pause mode, if you turn the jog, the point at which the sound is being produced moves by
a number of frames corresponding to the number of clicks. Clockwise moves the point forward,
counterclockwise moves the point backward. In play mode, the jog increases or decreases the
speed of the song( clockwise : increase , counterclockwise : decrease ).
3. TIME BUTTON
Use this knob to choose the time mode : Elapsed time, remaining time or total remaining time.
4. REPEAT BUTTON
Use this button to repeat one track or all the track of the CD.
5. A BUTTON ( LOOP SYSTEM )
This button sets the beginning of the loop. The Loop indicator on the display flashes.
6. CONT. / SINGLE BUTTON
Press these to switch between the SINGLE and CONTINUOUS play mode. The selected mode is
indicated on the LCD. In SINGLE mode, after each track, the unit stops the reading. In
CONTINOUS mode, the unit reads all track and stops.
2
7. PROG BUTTON
In STOP mode, you can program several tracks ( 20 tracks max ) :
- Press the STOP button to enter in the stop mode
- Press the PROG button to enter in the program mode
- Use the skip track buttons to choose the track you want to listen then press the PROG button to
enter your choice
- Use one more time the skip track buttons to choose the track you want to listen then press the
PROG button to enter your choice
- Repeat the operation to select all the track you want to listen
- Press the PLAY/PAUSE button to start the playback
8. B BUTTON ( LOOP BUTTON )
When you press this button, you set the end point of the seamless loop and you start the loop. To
finish the loop, press again this button.
9. EJECT BUTTON
Press to load or eject disk. Each press will open or close the disk tray.
NOTE: disc holder will not open unless stop or pause button has been pushed fir.
10. RELOOP BUTTON ( LOOP SYSTEM )
This button is used to start the last saved loop. To finish the loop, press the reloop button.
11. SKIP I<< BUTTON
Use this switch to re-start the track or to select the last track.
12. CUE BUTTON
Pressing the CUE button during play provides a return to the position at which play was started.
13. +10 BUTTON
Use this button to jump of 10 tracks in one press.
14. PLAY / PAUSE BUTTON
Each time you press the PLAY/PAUSE button, the operation changes from play to pause or from
pause to play.
15. SKIP >>I BUTTON
Use this knob to select the next track.
16. PITCH CONTROL
Use this fader to increase or decrease the speed of the track.
17. PITCH BEND + BUTTON
The pitch will automatically rise when the + button is pressed and return to the original pitch when
it is released.
18. PITCH BUTTON
If you push this button, the adjustement of the pitch potentiometer is available.
19. DISPLAY
20. STOP BUTTON
Press this button to stop the playback.
21. PITCH BEND - BUTTON
The pitch will drop while the - button is pressed and return to the original pitch when it is released.
22. DISC-TRAY
To enter the disc, please refer to the explanations under 6.2 CD-tray.
3
Connection :
23. LINE OUT 1-2
The audio for each CD player is an output for these jacks. Connect to the line input of the mixer.
24. POWER SUPPLY SWITCH
Use this selector to choose the good Power supply. (several countries have another power supply)
25. AC CORD
Use this cable to connect the AC mains power to the unit.
26. DIN SOCKET 1-2
Connect on all this sockets the mini-din cable provide with the CD player. Connect the player 1
with the part 1 of the controller and the player 2 with the part 2 of the controller.
4
WARRANTY CONDITIONS
MISTUBA equipment is covered by a 1-year warranty on parts and labour except for Crossfaders (90
days).
The following rules apply from the day the equipment leaves the factory:
The date on the invoice is considered to be the date the warranty begins.
Only companies approved by MISTUBA are allowed to work on the equipment. Warranty becomes
void when other service technicians open the equipment.
During warranty period, defective equipment must be sent by pre-paid mail in the original box.
MISTUBA will return the goods by pre-paid mail during the first year of warranty; thereafter the mailing
cost is to be paid by the recipient
Potentiometers have a limited lifetime and are not covered by the manufacturer for more than normal
use.
For all service enquiries, refer to your local distributor, as he is best able to help you.
SPECIFICATIONS :
Anti-Shock Buffer Memory :
Range of adjustments :
Power supply :
Dimensions :
40 seconds
+/- 12%
110/230V 50/60Hz
Player :482x90x255mm
Controller :482x90x80mm
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement