capitoltm bike rack
CAPITOL BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
7/32" hex bit for
tamper-resistant
screws
a
5/16" hex bit for
tamper-resistant
screws
b
TOOLS NEEDED
steel
wire brush
pencil
c
d
epoxy
STEP BY STEP
e
1/4", 1/2" & 7/8" drill
bits for concrete
hammer drill
epoxy gun
Loctite
FOR ALL CAPITOL BIKE RACKS
a
Mark hole locations
Drill holes
Fill holes & insert anchors
• Place base plate in desired location. Mark
center of each hole location with a pencil.
• Use hammer drill to drill 5" deep x 7/8"
diameter anchor hole at each marked
location using a 7/8" drill bit suitable for
concrete drilling.
• Use compressed air and steel wire brush
to clean each anchor hole in accordance
with epoxy instructions.
NOTE: Forms+Surfaces recommends
starting holes with 1/4" diameter drill
bit followed by 1/2" and finally 7/8" for
maximum accuracy.
• Use epoxy in epoxy gun to fill each anchor
hole 5/8 of the hole depth in accordance
with epoxy instructions.
• Insert 1/2"-13 x 5" epoxy anchor (a) into
each anchor hole so anchor top is flush
with ground. Allow proper curing time
according to cure schedule on epoxy
instructions before moving on to Step 4.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 3 | 09-02-15
CAPITOL BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL CAPITOL BIKE RACKS
b
c
d
e
Position base plate
Attach base plate
Attach bike rack & tighten screws
• Position base plate so that mounting
holes line up with anchors.
• Slide 1/2" stainless steel lock washer (c),
then 1/2" stainless steel flat washer (d)
onto each 1/2"-13 x 1-1/2" tamperresistant button head cap screw (b).
• Slide bike rack over base plate.
• Insert screws into mounting holes in base
plate and thread into anchors using
provided 5/16" hex bit for tamperresistant screws.
• Thread 5/16"-18 x 1" tamper-resistant
flat head cap screw (e) through each hole
using 7/32" hex bit for tamper-resistant
screws.
• Tighten all screws.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 3 | 09-02-15
CAPITOL BIKE RACK
TM
SURFACE MOUNT INSTALLATION INSTRUCTIONS
wall
wall
36" min
48" min
96" (72" min)
CAPITOL BIKE RACK
60" (48" min)
36"
(24" min)
36" min
96" (72" min)
wall
wall
RECOMMENDED BICYCLE RACK SPACING PER ASSOCIATION OF PEDESTRIAN AND BICYCLE PROFESSIONALS (APBP) GUIDELINES FOR ALL CAPITOL BIKE RACKS
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 3 | 09-02-15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement