HOW TO USE - The Home Depot

HOW TO USE - The Home Depot
22 HOW TO USE
ENGLISH
HOW TO USE
Before use
Clean the refrigerator.
Clean the refrigerator thoroughly and wipe off all dust that accumulated during
shipping.
Caution
yy Do not scratch the refrigerator with a sharp object or use a detergent that
contains alcohol, a flammable liquid or an abrasive when removing any tape
or adhesive from the refrigerator,.
yy Do not peel off the model or serial number label or the technical information
on the rear surface of the refrigerator.
Note
Remove adhesive residue by wiping it off with your thumb or dish detergent.
Open refrigerator and freezer doors to ventilate the interior.
The inside of the refrigerator may smell like plastic at first. Remove any adhesive
tape from inside the refrigerator and open the refrigerator and the freezer doors for
ventilation.
Connect the power supply.
Check if the power supply is connected before use.
Read the “Turning On The Power” section.
Turn off the icemaker if the refrigerator is not yet connected to the
water supply.
Turn off the automatic icemaker and then plug the power plug of the refrigerator
into the grounded electrical outlet.
* This is applicable only to certain models.
Caution
Running the automatic icemaker before connecting it to the water
supply may cause the refrigerator to malfunction.
Wait for the refrigerator to cool.
Allow your refrigerator to run for at least two to three hours before putting food in
it. Check the flow of cold air in the freezer compartment to ensure proper cooling.
Caution
Putting food in the refrigerator before it has cooled could cause the
food to spoil, or a bad odor could linger inside the refrigerator.
The refrigerator makes a loud noise after initial operation.
This is normal. The volume will decrease as the temperature lowers.
HOW TO USE 23
Wi-Fi Eclipse Display
ENGLISH
Depending on the model, some of the following functions may not be available.
Wi-Fi Eclipse Display Features
9
1
3
5
7
2
4
6
8
1 Smart Grid / Connect
Smart Grid
Press the Smart Grid button to turn the Smart
Grid function On/Off. When the function is on,
the icon illuminates. The Smart Grid function
automatically turns on when the refrigerator
is connected to the Wi-Fi network. When the
refrigerator is responding to a Demand Response
(DR) message from the electric company, the
Grid text illuminates.
Connect
The Connect button, when used with the LG
Electronics Smart Refrigerator smart phone app,
allows the refrigerator to connect to your home’s
Wi-Fi network. Refer to the Smart Features
section for information on the initial setup of the
application. The Connect icon indicates the status
of the refrigerator’s network connection. When
the refrigerator is connected to the network, the
Connect icon is illuminated. Press and hold the
Connect button for 3 seconds to connect to the
network. The icon will blink while the connection
is being made, then turn on once the connection
is successfully made. To disconnect, press and
hold the button again.
2 Lock
The Lock function disables every other button on
the display.
yy When power is initially connected to the
refrigerator, the Lock function is off.
yy To activate the Lock function, press and
hold the Lock button until the lock indicator
appears in the display. The other buttons are
now disabled.
yy To disable the Lock function, press and hold
the Lock button for approximately three
seconds.
3 Auto Open Door
The right refrigerator door opens automatically
if you place a foot near the motion sensor at the
bottom of the door. This is convenient when
you have both hands full of groceries and need
to open the refrigerator door. To set the Auto
Open Door function, press the button repeatedly
to toggle between the ON, Sound Off, and OFF
settings.
Using the Auto Open Door Function
111When the Auto Open Door Function is
enabled, text is displayed on the floor near
the motion sensor.
24 HOW TO USE
ENGLISH
2. Pass one foot in front of the motion sensor
and step on the displayed text. The right
door opens. If the door opens less than 20
degrees and is not opened further, it will
close automatically after 3 seconds.
Setting Auto Open Drawer
Press Auto Drawer to activate or deactivate the
function. When the function is activated, an icon
appears on the display.
Using Auto Open Drawer
Open the freezer door at least 85 degrees to
automatically open the drawers. Slowly close the
door to automatically close the drawers.
Note
Place your foot close enough to the
sensor that the text appears on top of
the foot, not just on the toes.
Caution
Disable the Auto Open Door function
if you have young children or people
lacking in cognitive ability in the home.
They could be injured if the door opens
unexpectedly while they are nearby.
Note
yyThe displayed text may not
be readable on some flooring
materials, but this will not affect the
performance of the Auto Open Door
function.
yyIf flooring material is highly reflective
(metal, glass tile), the motion sensor
may malfunction and the Auto Open
Door function may not work properly.
yyReflective objects placed in front of
the motion sensor may cause the text
to display, but the text disappears if
no movement is detected.
yyIf a pet passes by below when a
person stands in front of the product,
automatic door open function may be
operated.
4 Auto Open Drawer
More than 85°
Caution
yyDo not use excessive force to push or
pull the freezer drawers.
yyDo not slam the freezer door shut
while the drawers are open.
Failure to follow these warnings may
result in personal injury or damage to
the product.
5 Refrigerator/Door Alarm
Refrigerator
yy Indicates the set temperature of the
refrigerator compartment in Celsius (°C) or
Fahrenheit (°F). The refrigerator temperature
control ranges from 33°F to 46°F (1°C to 8°C).
The recommended temperature setting for the
refrigerator compartment is 37°F (3°C).
Door Alarm
yy The door alarm sounds when a refrigerator
or freezer door is left open for more than 60
seconds.
yy To stop the alarm, close the doors.
When Auto Open Drawer is enabled, the freezer
drawers automatically open when the freezer
door is opened. The drawers automatically close
when the freezer door is closed.
yy The door alarm is enabled by default. To disable
the door alarm, press and hold Door Alarm for
three seconds.
HOW TO USE 25
6 Freezer
To change the temperature mode from °F to °C
(or vice versa) press and hold the Refrigerator
and Freezer temperature buttons simultaneously
for approximately five seconds. The temperature
indication on the display window switches
between Celsius and Fahrenheit.
Note
The displayed temperature is the target
temperature, and not the actual temperature
of the refrigerator. The actual refrigerator
temperature depends on the food inside the
refrigerator.
7 Fresh Filter
The Fresh Air Filter helps remove odors from the
refrigerator. The Fresh Air Filter has two settings,
Auto and Power(PWR). In Auto mode, the Fresh
Air Filter will cycle on and off in increments of
ten minutes on and 110 minutes off. If set to the
Power(PWR) mode, the Fresh Air Filter will stay
on continuously for four hours, cycling on and off
in increments of ten minutes on and five minutes
off. After four hours, the Fresh Air Filter will
switch back to Auto mode.
yy Press the Fresh Air Filter button once for
Power(PWR) mode.
yy Press the Fresh Air Filter button again to
switch back to Auto mode.
8 Ice Plus
This function increases both ice making and
freezing capabilities.
yy Press Ice Plus to illuminate the icon in the
display and activate the function for 24 hours.
After 24 hours, the icon and the function
automatically turn off.
yy To deactivate the function manually, press Ice
Plus again.
The display indicates the current status of the
refrigerator. Press any button to display the
current setting for that function.
Using the Wi-Fi Eclipse Display
yy To turn the display on, open a refrigerator
or freezer door or knock twice on the
InstaView™Door-in-Door® to activate the
interior LED
yy The display turns off automatically five
seconds after all the doors are closed or five
seconds after you have knocked twice on
the InstaView™Door-in-Door®.
yy The display buttons operate using static
electricity. Wear gloves while cleaning to
avoid activating button functions.
yy Keep the display clean and free from foreign
substances. Skin must contact the buttons
directly for them to properly function.
yy Wipe any moisture off the display before
using it. Moisture on the display may
interfere with the functioning of the buttons.
Caution
Display Mode (For Store Use Only)
The Display Mode disables all cooling in the
refrigerator and freezer sections to conserve
energy while on display in a retail store. When
you turn on the interior display, “Demo Mode”
appears in the display.
To deactivate / activate:
With InstaView™Door-in-Door® opened, press
and hold the Refrigerator and Ice Plus buttons
at the same time for five seconds. When demo
mode is activated, the control panel will beep
and the temperature settings will display as
“Demo Mode” for five seconds and then return
to normal temperature display. Use the same
procedure to deactivate the Display Mode.
ENGLISH
Indicates the set temperature of the freezer
compartment in Celsius (°C) or Fahrenheit (°F).
The freezer temperature control ranges from
-6°F to 8°F (-21°C to -13°C). The recommended
temperature setting for the freezer compartment
is 0°F (-18°C).
9 Display
26 HOW TO USE
Smart Features
ENGLISH
To use the Smart Features on your refrigerator, you will need the following devices and apps:
1. a wireless router and home Wi-Fi network
2. the LG Smart Grid refrigerator
3. an Android-based smart phone
4. the LG Smart Refrigerator app from the Google Play Store.
Note
To use the Smart Grid feature, you must also register for the Smart Grid (Demand Response)
service with your local electric utility company. The company must provide Demand Response
service.
Setting Up the Smart App and Connecting the Refrigerator
1
Create an account at Smart ThinQ.
https://us.smartthinq.com/
You will use the ID and password from this
account in the smart phone application.
2
Download the smart phone app from the
Google Play Store. (LG Smart Refrigerator
app)
3
In the app, select the Smart Model.
4
Log in to the app using the Smart ThinQ ID
and password created in step 1.
5
When prompted, select the Non Touch
Screen Model.
6
Choose your home wireless router
from the list of routers in the app. Your
refrigerator and smart phone must both be
connected to the same Wi-Fi network.
Note
You must connect the refrigerator to the
internet using a wireless router on your
home network. Tethering to a mobile phone,
hotspot, or an unsecured network, for
example, will cause unstable functionality.
7
If necessary, enter the password for your
router and click the connect button in the
app.
8
Make sure the refrigerator display is active
by pressing any button. Press and hold the
Smart Grid button on the refrigerator for
three seconds. The Connect LED should
blink while the connection is being made.
9
The app will automatically go through the
process of registering your product on
the network, using the information you’ve
provided. This may take some time, and
the Connect LED will continue to blink
during this process. After the registration
process is completed, a message is
displayed and the app will proceed to the
Home screen.
10 Check that the Connect LED is illuminated
to confirm that the Wi-Fi network is
connected. You can now use the app
to control the Smart Features on your
refrigerator.
HOW TO USE 27
Food Manager
Allows you to keep track of items in your
refrigerator and freezer, so you can be alerted
when they are near their use-by dates, generate
grocery lists, and link to related recipes.
Recipes
Features recipes from the Food Channel,
searchable by ingredient, course, cuisine, total
time required, and the food in your refrigerator
(if entered in the Food Manager). Automatically
makes grocery lists from chosen recipes.
Grocery
Makes and manages grocery lists from items in
your refrigerator or recipes.
Refrigerator Manager
Allows you to control the refrigerator and freezer
temperature settings, air filter, water filter, Ice
Plus, Smart Saving, and Energy Monitoring from
your smart phone.
Smart Diagnosis
Allows you to diagnose and troubleshoot
problems with your refrigerator.
Settings
Allows you to set various options on the
refrigerator and in the app.
Smart Grid Function
When the refrigerator operates in Smart Grid
mode, the Smart Refrigerator function can control
energy usage or delay the operation of some
functions to save energy during peak usage
periods.
yy You can override the Smart Grid function
at any time (using the Smart Grid button or
application).
yy To use the Smart Grid function, you need to
register your appliance with your electric utility
company.
Using the Smart Grid Function
This feature responds to notification events
from your utility company to run high energyconsuming tasks during off-peak periods when
demand is lower. These notification events are
known as Demand Response signals.
If the refrigerator receives a Demand Response
signal from the utility company, the refrigerator
will turn on the Grid LED on the refrigerator
display and control its power consumption
according to the signal.
The refrigerator will respond to the signals
received from the utility company as long as
product performance is maintained.
If the refrigerator receives a Demand Response
signal, the refrigerator will operate in Delay
Appliance Load (DAL) or Temporary Appliance
Load Reduction (TALR) mode.
Delay Appliance Load (DAL): The refrigerator
responds to a DAL signal by providing a moderate
load reduction for the duration of the delay period.
This mode controls functions that consume a lot
of energy such as adjusting the cooling system,
running the defrost cycle, and making ice.
-W
hen the refrigerator operates in DAL mode,
the Grid LED is illuminated on the refrigerator
display.
-D
AL mode is automatically deactivated after it
lasts for the amount of time stipulated by the
DAL signal (max. 4 hours) or when you override
the Smart Grid function.
Temporary Appliance Load Reduction (TALR) :
The refrigerator responds to a TALR signal by
aggressively reducing the load for a short time
period, typically 10 minutes. This mode reduces
energy consumption by stopping the compressor
and controlling the functions that consume a lot
of energy such as the defrost cycle and fan.
-W
hen the refrigerator operates in TALR mode,
the Grid LED is illuminated on the refrigerator
display.
-T
ALR mode is automatically deactivated after it
lasts for the received duration (max. 10 minutes),
or when you override the Smart Grid function.
The mode is immediately deactivated and the
refrigerator returns to its normal state when the
door is opened or closed, or the dispenser is
used.
ENGLISH
LG Smart Refrigerator App - What’s
Included
28 HOW TO USE
ENGLISH
Smart Features (continued)
Smart Grid Application Features
Override Smart Grid Mode
1
You can lower energy usage based on
Demand Response (DR) signals from the
utility company.
If you want the refrigerator to ignore the Demand
Response signal from the utility company, you
can override the Smart Grid function by pushing
the Smart Grid button while the refrigerator is in
Smart Grid mode.
When you override the Smart Grid function, the
refrigerator ignores the Demand Response signal
and is no longer controlled by the utility company
until the next Demand Response signal is sent.
If the refrigerator is operating in Smart
Saving mode according to the DR signal,
you can see a pop up.
Smart Saving_Delay Defrost
Lower energy usage based on time period.
2
You can also override the Smart Grid function
using the smart phone app.
Open API
Energy monitoring
The refrigerator can check number of door
openings and power consumption.
3
Remote Control
You can control the Refrigerator
Temperature, Fresh Air Filter and Ice Plus
from the smart phone app.
LG Open API
You can manage Smart Grid features for the LG
Smart Refrigerator.
Smart Saving_Demand Response
4
Push messages.
Please check the detailed specifications on the
notice page on us.smartthinq.com.
- When the door is open over ten minutes,
you will receive a push message.
API list :
- When Ice Plus is finished, you will receive
a push message.
Demand response
- Send demand response signal
Power saving
- Set saving mode
- Get schedule of DR/Delay Defrost
Energy monitoring
- Get setting temperature
- Get door open event
- Get energy consumption
Delay defrost capability
- Insert a delay defrost schedule event
- Update a delay defrost schedule event
- Delete a delay defrost schedule event
- Get the delay defrost schedule
Open Source Software Notice
Information
To obtain the source code that is contained in
this product that was developed under GPL,
LGPL, MPL, and other open source licenses,
visit http://opensource.lge.com. In addition to the
source code, all referred license terms, warranty
disclaimers and copyright notices are available for
download.
LG Electronics will also provide open source code
on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost
of media, shipping, and handling) upon email
request to [email protected] This offer is
valid for three (3) years from the date on which
you purchased the product.
Wireless LAN module Specifications
Model
LCW-003
Frequency Range
2412 to 2462MHz
Output Power
(Max.)
IEEE 802.11b: 17.56 dBm
IEEE 802.11g: 25.53 dBm
IEEE 802.11n: 25.29 dBm
HOW TO USE 29
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
-R
eorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
-C
onnect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be colocated or operating in conjunction with any other
antenna or transmitter.
This equipment should be installed and operated
with minimum distance 20 cm (7.8 inches)
between the antenna and your body. Users must
follow the specific operating instructions for
satisfying RF exposure compliance.
Industry Canada Statement (For
transmitter module contained in this
product)
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
1) this device may not cause interference; and
2) t his device must accept any interference,
including interference that may cause undesired
operation of the device.
-C
onsult the dealer or an experienced radio/TV
technician for help.
IC Radiation Exposure Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed
and operated with minimum distance 20 cm
(7.8 inches) between the antenna & your body.
1) this device may not cause harmful interference
and
2) this device must accept any interference
received, including interference that may cause
undesired operation of the device.
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
Note
The manufacturer is not responsible
for any radio or TV interference caused
by unauthorized modifications to this
equipment. Such modifications could
void the user’s authority to operate the
equipment.
ENGLISH
FCC Notice (For transmitter module
contained in this product)
30 HOW TO USE
FCC Regulation Notice
Wireless Power Transfer Specifications
ENGLISH
This device complies with Part 18 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference
and
(2) this device must accept any interference
received, including interference that may
cause undesired operation of the device.
Frequency
350 kHz ± 20kHz
Rated voltage
DC 12V
Delivered power
Less than or equal to 1.2W
per shelf
Transmission
mode
Electromagnetic induction
Any changes or modifications in construction of
this device which are not expressly approved by
the party responsible for compliance could void
the user’s authority to operate the equipment.
This device has no serviceable parts.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Transmitter
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Model
FCC ID
LUPXS3186N
BEJF31GDA
LUPXC2386N
BEJF23GDA07
Industry Canada Statement
This device complies with Industry
Canada’slicense-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.
CAN RSS-216 / CNR-216
Receiver
Note
yy Installing the shelf on the right side will
disable the shelf light.
yy The shelf light turns on only when the
shelf is installed in the highest or lowest
positions.
yy Foreign objects and dirt between the shelf
and the inner cabinet wall could prevent
the shelf light from turning on.
yy The shelf light turns on when the door is
opened.
yy The shelf light turns off after seven
minutes or when the door is closed.
HOW TO USE
31
In-Door Ice Bin
2
Caution
To remove the in-door ice bin, grip the
front handle, slightly lift the lower part,
and slowly pull out the bin as shown.
yy Keep hands and tools out of the ice
compartment door and dispenser chute.
Failure to do so may result in damage or
personal injury.
yy The icemaker stops producing ice when the
in-door ice bin is full. If you need more ice,
empty the ice bin into the extra ice bin in
the freezer compartment. During use, ice
may build up higher around the sensor than
in the rest of the bin, causing the icemaker
to stop producing ice before the bin is full.
Shaking the ice bin to level the ice within it
can reduce this problem.
yy To avoid damaging the icemaker, do not
store cans or other items in the ice bin.
yy Keep the ice compartment door closed
tightly. If the ice compartment door is not
closed tightly, the cold air in the ice bin will
freeze food in the refrigerator compartment.
This could also cause the icemaker to stop
producing ice.
yy If the icemaker is turned OFF for
an extended period of time, the ice
compartment will gradually warm up
to the temperature of the refrigerator
compartment. To prevent ice cubes from
melting and leaking from the dispenser,
ALWAYS empty the ice bin when the
icemaker is set to Off for more than a few
hours.
Assembling the In-Door Ice Bin
1
Carefully insert the in-door ice bin while
slightly slanting it to avoid contact with the
icemaker.
2
Avoid touching the auto shutoff (feeler
arm) when replacing the ice bin. See the
label on the ice compartment door for
details.
Auto shutoff
(feeler arm)
Detaching the In-Door Ice Bin
1
Gently pull the handle to open the ice
compartment.
Caution
When handling the ice bin,
keep hands away from
the icemaker tray area to
avoid personal injury.
ENGLISH
Depending on the model, some of the
following functions may not be available.
32 HOW TO USE
Automatic Icemaker
ENGLISH
Depending on the model, some of the
following functions may not be available.
Ice is made in the automatic icemaker and sent
to the dispenser. The icemaker will produce
70-182 cubes in a 24-hour period, depending
on freezer compartment temperature, room
temperature, number of door openings and
other operating conditions.
Warning
Personal Injury Hazard
DO NOT place fingers or hands on the
automatic ice making mechanism while the
refrigerator is plugged in.
Icemaker
yy It takes about 12 to 24 hours for a newly
installed refrigerator to begin making ice. Wait
72 hours for full ice production to occur.
yy Ice making stops when the in-door ice bin
is full. When full, the in-door ice bin holds
approximately 6 to 8 (12-16 oz) glasses of ice.
yy Foreign substances or frost on the auto shutoff
(feeler arm) can interrupt ice production. Make
sure the feeler arm is clean at all times for
proper operation.
yy To increase ice production, use the Ice Plus
function. The function increases both ice
making and freezing capabilities.
Auto shutoff (feeler arm)
Turning the Automatic Icemaker
On or Off
To turn the automatic icemaker On/Off, press
and hold the Ice On/Off button on the control
panel for 3 seconds.
HOW TO USE 33
Caution
yy The first ice and water dispensed may
include particles or odor from the water
supply line or the water tank.
yy Throw away the first few batches of ice.
This is also necessary if the refrigerator has
not been used for a long time.
yy Never store beverage cans or other items in
the ice bin for the purpose of rapid cooling.
Doing so may damage the icemaker or the
containers may burst.
yy If discolored ice is dispensed, check the
water filter and water supply. If the problem
continues, contact a qualified service
center. Do not use the ice or water until the
problem is corrected.
yy Keep children away from the dispenser.
Children may play with or damage the
controls.
yy The ice passage may become blocked with
frost if only crushed ice is used. Remove the
frost that accumulates by removing the ice
bin and clearing the passage with a rubber
spatula. Dispensing cubed ice can also help
prevent frost buildup.
yy Never use thin crystal glass or crockery to
collect ice. Such containers may chip or
break resulting in glass fragments in the ice.
yy Dispense ice into a glass before filling it
with water or other beverages. Splashing
may occur if ice is dispensed into a glass
that already contains liquid.
yy Never use a glass that is exceptionally
narrow or deep. Ice may jam in the ice
passage and refrigerator performance may
be affected.
yy Keep the glass at a proper distance from
the ice outlet. A glass held too close to the
outlet may prevent ice from dispensing.
yy To avoid personal injury, keep hands out of
the ice door and passage.
yy Never remove the dispenser cover.
yy If ice or water dispenses unexpectedly, turn
off the water supply and contact a qualified
service center.
When You Should Turn the
Icemaker Off
yy When the water supply will be shut off
for several hours.
yy When the ice bin is removed for more
than one or two minutes.
yy When the refrigerator will not be used
for several days.
Note
The ice bin should be emptied when
the Ice On/Off button is set to the Off
mode.
Normal Sounds You May Hear
yy The icemaker water valve will buzz as
the icemaker fills with water. If the Ice
on/off button is set to On, the icemaker
will buzz even if it has not yet been
hooked up to water. To stop the buzzing,
press the Ice on/off button to set it to
the Off position.
Note
Keeping the icemaker on before the
water line is connected can damage the
icemaker.
yy You will hear the sound of cubes
dropping into the bin and water running
in the pipes as the icemaker refills.
Preparing for Vacation
Set the Ice On/Off button to Off and shut off
the water supply to the refrigerator.
Note
The ice bin should be emptied any time
the Ice On/Off button is turned Off.
If the ambient temperature is expected to drop
below freezing, have a qualified technician
drain the water supply system to prevent
serious property damage due to flooding
caused by ruptured water lines or connections.
ENGLISH
Automatic Icemaker
(continued)
34 HOW TO USE
Ice and Water Dispenser
ENGLISH
The measured fill function dispenses premeasured amounts of water automatically.
Caution
Keep children away from the dispenser
to prevent them from playing with or
damaging the controls.
Dispenser
Ice On/Off
Cubed
Water
Crushed
Hold 3sec
Using the Measured Fill
1
Select the desired amount from the
Measured Fill buttons on the dispenser
control panel.
2 Depress the dispenser switch with a
container.
3 To stop the measured fill, release the
dispenser switch.
Water Filter
Reset Hold 3sec
4 oz
8 oz
16 oz
32 oz
Note
Measured Fill
Ice and Water
switch
yy If discolored ice is dispensed, check
the water filter and water supply. If the
problem continues, contact a qualified
service center. Do not use the ice or
water until the problem is corrected.
Stand
yy The dispenser will not operate when
either of the refrigerator doors are open.
Using the Dispenser
yy If dispensing water or ice into a container
with a small opening, place it as close to
the dispenser as possible.
yy Some dripping may occur after
dispensing. Hold the cup beneath the
dispenser for a few seconds after
dispensing to catch all of the drops.
1 Turn the icemaker on or off by pressing
and holding Ice On/Off for three seconds.
2
Cleaning the Dispenser Stand
1
To dispense cold water or ice, press the
text on the dispenser control panel to select Cubed ice( ), Water( ), or Crushed
ice( ).
Raise up, holding both ends.
Ice On/Off
Cubed
Water
Crushed
Hold 3sec
Water Filter
Reset Hold 3sec
4 oz
8 oz
16 oz
32 oz
Measured Fill
Caution
Throw away the first few batches of ice
(about 24 cubes). This is also necessary
if the refrigerator has not been used for
a long time.
2
Wipe out dirty areas with a clean cloth.
Locking the Dispenser
Press and hold the Lock button on the interior
display for three seconds to lock the dispenser
and all of the display panel functions. Follow
the same instructions to unlock.
HOW TO USE 35
Storing Food
Each compartment inside the refrigerator is designed to store different types of food.
Store your food in the optimal space to enjoy the freshest taste.
Refrigerator Bin
Store beverages, water, etc.
Crisper
Preserve vegetables and
fruits.
Freezer Drawer (1)
Preserve small packaged
frozen food or frequently-used
foods.
Freezer Bin
Preserve small packaged
frozen food or frequentlyused foods.
Adjustable refrigerator
shelf
Adjustable shelves to
meet individual storage
needs.
InstaView™
Door-in-Door®
Store frequently
used items such as
condiments, beverages,
butter, or cheese.
Hidden Bar Tray
Store small items or
defrost frozen items.
Freezer Drawer(2)
Preserve frozen food for longer storage.
Caution
yy Do not store food with high moisture content toward the top of the refrigerator. The moisture could
come in direct contact with the cold air and freeze.
yy Wash food before storing it in the refrigerator. Vegetables and fruit should be washed, and food
packaging should be wiped down to prevent adjacent foods from being contaminated.
yy If the refrigerator is kept in a hot and humid place, frequent opening of the door or storing a lot of
vegetables in the refrigerator may cause condensation to form. Wipe off the condensation with a
clean cloth or a paper towel.
yy If the refrigerator door or freezer drawer is opened too often, warm air may penetrate the refrigerator
and raise its temperature. It can also increase the cost to run the appliance.
yy Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or
personal injury if items are removed with excessive force.
yy The temperature inside the FRESHSteel Container is slightly lower than in the shelf or door bin area.
Note
yy If you are leaving home for a short period of time, like a short vacation, the refrigerator should be left
on. Refrigerated foods that are able to be frozen will stay preserved longer if stored in the freezer.
yy If you are leaving the refrigerator turned off for an extended period of time, remove all food and unplug
the power cord. Clean the interior, and leave the door open to prevent fungi from growing in the
refrigerator.
ENGLISH
Food Preservation Location
36 HOW TO USE
Food Storage Tips
ENGLISH
The following tips may not be applicable
depending on the model.
Wrap or store food in the refrigerator in airtight
and moisture-proof material unless otherwise
noted. This prevents food odor and taste transfer
throughout the refrigerator. For dated products,
check date code to ensure freshness.
Food
How to
Butter or
Margarine
Keep opened butter in a covered
dish or closed compartment.
When storing an extra supply,
wrap in freezer packaging and
freeze.
Cheese
Store in the original wrapping
until you are ready to use it.
Once opened, rewrap tightly in
plastic wrap or aluminum foil.
Milk
Wipe milk cartons. For coldest
milk, place containers on
interior shelf.
Eggs
Store in original carton on
interior shelf, not on door shelf.
Fruit
Do not wash or hull the fruit
until it is ready to be used. Sort
and keep fruit in its original
container, in a crisper, or store
in a completely closed paper
bag on a refrigerator shelf.
Leafy
Vegetables
Remove store wrapping and
trim or tear off bruised and
discolored areas. Wash in cold
water and drain. Place in plastic
bag or plastic container and
store in crisper.
Vegetables
with skins
(carrots,
peppers)
Place in plastic bags or plastic
container and store in crisper.
Fish
Store fresh fish and shellfish
in the freezer section if they
are not being consumed the
same day of purchase. It is
recommended to consume
fresh fish and shellfish the
same day purchased.
Leftovers
Cover leftovers with plastic wrap
or aluminum foil, or store in
plastic containers with tight lids.
Storing Frozen Food
Note
Check a freezer guide or a reliable cookbook
for further information about preparing food
for freezing or food storage times.
Freezing
Your freezer will not quick-freeze a large
quantity of food. Do not put more unfrozen
food into the freezer than will freeze within
24 hours (no more than 2 to 3 lbs. of food per
cubic foot of freezer space). Leave enough
space in the freezer for air to circulate around
packages. Be careful to leave enough room at
the front so the door can close tightly.
Storage times will vary according to the quality
and type of food, the type of packaging or wrap
used (how airtight and moisture-proof) and
the storage temperature. Ice crystals inside a
sealed package are normal. This simply means
that moisture in the food and air inside the
package have condensed, creating ice crystals.
Note
Allow hot foods to cool at room temperature
for 30 minutes, then package and freeze.
Cooling hot foods before freezing saves
energy.
HOW TO USE 37
Detaching the Shelf
Packaging
Tilt up the front of the shelf and lift it straight
up. Pull the shelf out.
Successful freezing depends on correct
packaging. When you close and seal the
package, it must not allow air or moisture in or
out. If it does, you could have food odor and
taste transfer throughout the refrigerator and
could also dry out frozen food.
Packaging recommendations:
yy Rigid plastic containers with tight-fitting
lids
yy Straight-sided canning/freezing jars
yy Heavy-duty aluminum foil
yy Plastic-coated paper
yy Non-permeable plastic wraps
yy Specified freezer-grade self-sealing plastic
bags
Assembling the Shelf
Tilt the front of the shelf up and guide the rear
shelf hooks into the slots at the desired height.
Then, lower the front of the shelf so that the
hooks drop into the slots.
Follow package or container instructions for
proper freezing methods.
Do not use
yy Bread wrappers
yy Non-polyethylene plastic containers
yy Containers without tight lids
yy Wax paper or wax-coated freezer wrap
yy Thin, semi-permeable wrap
Adjusting the Refrigerator
Shelves
Caution
Make sure that shelves are level from
one side to the other. Failure to do so
may result in the shelf falling or food
spilling.
The shelves in the refrigerator are adjustable
to meet individual storage needs. Your model
may have either glass or wire shelves.
Adjusting the shelves to fit items of different
heights will make finding the exact item you
want easier. Doing so will also reduce the
amount of time the refrigerator door is open
which will save energy.
LEFT
Note
yy The left side shelf has "LEFT" marking.
yy If left and right side shelves are
switched, they will not be assembled.
ENGLISH
Storing Frozen Food (continued)
38 HOW TO USE
When Closing the Door
CustomChill™ Pantry
ENGLISH
This space is used to store meat, fish, dairy
products, beverages, and other items that
need to be kept chilled.
Setting the CustomChill™ Pantry
Choose a temperature setting for the
CustomChill™ pantry by pressing the Select
button repeatedly to toggle between Meat,
Deli, or Produce.
Caution
yy To reduce the risk of door scratches
and breaking the center door mullion,
make sure that the refrigerator door
mullion is always folded in.
yy The door alarm sounds every 30
seconds if the door remains open
longer than one minute. Ensure that
the folding mullion is folded in before
closing the left-hand door.
The temperature setting becomes
progressively colder from Produce → Deli →
Meat.
Caution
Vegetables or fruit may freeze if placed
in the CustomChill™ pantry when it is
set to Meat or Deli.
HOW TO USE 39
Assembling the Crisper Drawers
Removing the Crisper Drawers
1
Pull out the crisper drawer support until it
stops. Angle the crisper drawer into the
opening to place it on the support.
2
Slide the crisper drawer back on the
support until it drops into place and then
close the crisper drawer.
1
Pull the crisper drawer out until it stops.
2
Slightly lift the crisper drawer to remove it
from the support.
Caution
yy Always empty the crispers before
removing them, and use both hands
when removing and assembling them.
yy Make sure that the refrigerator doors
are fully open before removing and
assembling the crispers.
ENGLISH
Crisper Drawers
40 HOW TO USE
Removing the Crisper Support Box
ENGLISH
1
Fully open the fridge door and pull out all
the shelves.
Caution
yy To avoid injury, always empty the shelves
and crisper drawers before removing
them.
2
5
Slide one hand under the crisper support
box and tilt the box up slightly to remove
it.
Assembling the Crisper Support Box
1
Use one hand to support the bottom of the
crisper support box while aligning the inner
edge of the box with the groove inside the
refrigerator. Lower the box into place.
2
Angle the crisper cover into the refrigerator
and then lower it into place.
3
Slide the crisper cover back until it stops.
Lift the front of the crisper cover until you
hear a loud click.
3 Tilt the cover slightly and support it with
one hand while pulling it out.
4
Open the convertible pantry and lift the
front side of the crisper support box with
both hands.
HOW TO USE
InstaView™Door-in-Door®
Knock twice on the center of the glass panel
to reveal the contents of the door bins without
opening the door and allowing the cold air to
escape.
Remove the contents from the CustomChill™
pantry before removing the insert. To remove,
open the drawer to full extension, lift the front
of the insert, and pull it out.
Hidden Bar Tray
The Hidden Bar Tray compartment is slightly
cooler than the shelf or door bin areas, so it
is a convenient place to store dairy snacks or
other small items you want to keep especially
cold. It is also a handy place to defrost meat.
yy Knocking twice on the glass panel turns the
interior LED on or off.
yy The LED turns off automatically after
5 seconds.
yy The InstaView™ function is disabled when
the right refrigerator door is open, for two
seconds after closing the door, and when
the ice dispenser is in use.
Warning
Do not hit the glass door panel with
excessive force. Do not allow hard
objects like cookware or glass bottles
to hit the glass door panel. The glass
could break, resulting in a risk of
personal injury or product damage.
Note
To open cover, push handle toward
rear of bin to release catch.
To close cover, slide cover over bin
until catch clicks into place.
Caution
yy Be careful when handling and storing
larger eggs. They can be broken if the
cover is not completely closed and the
drawer above is pushed in.
yy Store foods like tofu, celery or lettuce
which have high water content or freeze
easily on the interior shelves at the front.
Note
yy Tapping the edges of the glass panel
may not activate the InstaView™
function.
yy The taps on the glass panel must be
hard enough to be audible.
yy Loud noises near the refrigerator
may activate the InstaView™
function.
yy The InstaView™Door-in-Door® will
not open if the right refrigerator door
is open.
ENGLISH
Removing the CustomChill™
Pantry Insert
41
42 HOW TO USE
ENGLISH
EasyLift Bin
Freezer Drawer
Move the EasyLift bin up and down easily and
conveniently as necessary.
Use the upper compartments to store
packaged frozen foods and frequently-used
foods.
yy Remove all items from the EasyLift bin before
moving it up or down.
Use the lower compartments for larger frozen
foods and items stored for longer periods.
yy Adjusting the EasyLift Bin allows taller food
items to be stored more conveniently.
1
2
To raise the EasyLift bin, hold the bottom
of the bin in the center and push the bin
up until it clicks into place.
To lower the EasyLift bin, press up to
release the levers at the bottom of the bin
and lower the bin until it clicks into place.
Caution
yyTo avoid personal injury or damage to the
bin or its contents, empty the EasyLift bin
before moving it up or down.
yy The sliding freezer drawers allow easy
access and convenience of use.
Removing the Freezer Drawer
1
Pull the freezer drawer out until it stops.
Empty all contents out of the drawer
before removing it.
2
Lift the empty freezer drawer slightly to
remove it from the support.
Caution
yyThe drawers are heavy. Always use two
hands when removing or assembling
the drawers to avoid product damage or
personal injury. Always empty drawers
before removing them.
yyAlways open the freezer doors completely
before removing or assembling the
drawers.
HOW TO USE 43
Removing the Drawer Support
1
Pull out the drawer support until it stops.
Angle the drawer into the space and set it
on the support.
1
Press the levers on either side of the
drawer support.
2
Slide the drawer back until it lowers into
place on the support. Close the drawer.
2
Keeping both levers pressed, lift the
drawer support slightly and remove it from
the rail system.
Caution
yyThe drawers are heavy. Always use two
hands when removing or assembling
the drawers to avoid product damage or
personal injury. Always empty drawers
before removing or assembling them.
yyAlways open the freezer doors completely
before removing or assembling the
drawers.
ENGLISH
Assembling the Freezer Drawer
44 HOW TO USE
ENGLISH
Assembling the Drawer Support
1. Left Refrigerator Door Bins
1
To remove the door bins, hold the bin with
both hands and lift up to remove it.
2
Pull both drawer rails out until they stop.
Line up the bottom edges on the sides
of the drawer support with the groove in
each rail and then lower the support until it
clicks into place.
To replace the freezer door bin, align both
sides of the bin with the guides and push the
bin down until it snaps into place.
Using the Door-in-Door Bin Bars
The metal bars attached to the Door-in-Door
bins can be used as either rails or dividers.
1
To keep tall items secure in the door bin,
unfold the bar and extend it upward from
the top of the bin as a rail.
2
To keep bin contents organized, unfold
the bar and extend it back into the bin as a
divider.
3
Fold the bar down into the front of the bin
when not in use.
Refrigerator/Freezer Door Bins
You can store small packaged frozen food
in the freezer door bins, or small packaged
refrigerated food or beverages in the
refrigerator door bins, such as milk, water,
juice, beer, etc.
Do not store ice cream or foods intended for
long-term storage in the freezer door bins.
1
3
2
2
HOW TO USE 45
2
Hold both ends of the bin and lift.
ENGLISH
2. Freezer Bins and Lower
InstaView™Door-in-Door® bin
To remove the door bins, tilt the front of the
bin up slightly while pulling the sides forward.
To replace,align the bottom bin tabs with the
rail slots then push the bin in until it clicks into
place.
Assembling
1
Make sure the bin latches are fully open.
Slightly tilt the front of the bin up to align
and insert the plastic tabs on the sides of
the bin into the indents in the rails. Hold
the sides of the bin and pull it slightly
forward to correctly position the latches.
2
Close the latches by rotating them toward
the sides of the bin.
3. Upper InstaView™Door-in-Door®
bin
Removing
1
Open the latches underneath the bin by
rotating them inwards. Tilt the front of
the bin up until the tabs on the top sides
clear the rails, then push the bin slightly
backward. (It may help to open the glass
InstaView™ door.)
46 MAINTENANCE
ENGLISH
MAINTENANCE
Cleaning
yy Both the refrigerator and freezer sections defrost automatically; however, clean both
sections about once a month to prevent odors.
yy Wipe up spills immediately.
yy Always unplug the refrigerator before cleaning.
General Cleaning Tips
yy Unplug refrigerator or disconnect power.
yy Remove all removable parts, such as
shelves, crispers, etc.
yy Use a clean sponge or soft cloth and a
mild detergent in warm water. Do not
use abrasive or harsh cleaners.
yy Hand wash, rinse and dry all surfaces
thoroughly.
Inside Walls (allow freezer to warm
up so the cloth will not stick)
To help remove odors, you can wash the inside
of the refrigerator with a mixture of baking
soda and warm water. Mix 2 tablespoons of
baking soda to 1 quart of water (26 g soda
to 1 liter water) Be sure the baking soda is
completely dissolved so it does not scratch the
surfaces of the refrigerator.
Door Liners and Gaskets
Exterior
Waxing external painted metal surfaces helps
provide rust protection. Do not wax plastic
parts. Wax painted metal surfaces at least
twice a year using appliance wax (or auto paste
wax). Apply wax with a clean, soft cloth.
For products with a stainless steel exterior,
use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use abrasive
or harsh cleaners. Dry thoroughly with a soft
cloth.
Caution
yy Do not use a rough cloth or sponge
when cleaning the interior and exterior
of the refrigerator.
yy Do not place your hand on the bottom
surface of the refrigerator when
opening and closing.
Warning
Use non-flammable cleaner. Failure to do
so can result in fire, explosion, or death.
Use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use cleaning
waxes, concentrated detergents, bleaches,
or cleaners containing petroleum on plastic
refrigerator parts.
Plastic Parts (covers and panels)
Use a clean sponge or soft cloth and a mild
detergent in warm water. Do not use glass
cleaners, abrasive cleansers, or flammable
fluids. These can scratch or damage the
material.
Condenser Coils
Use a vacuum cleaner with an attachment to
clean the condenser cover and vents. Do not
remove the panel covering the condenser coil
area.
MAINTENANCE 47
Replacing the Fresh Air Filter
yy Approximately every six months.
yy When the Fresh Filter LED blinks or the
Replace Filter icon is displayed.
Remove the old filter.
Insert the side tab of the new filter into
the slot on the side of the central cover
compartment. Snap the other side of
the filter down into place. It may help to
press the side of the central compartment
outward while pressing down on the filter.
Make sure the side of the filter labeled
"Back" is facing out. Snap the cover of the
filter back onto the filter compartment in
the refrigerator.
BACK
Remove the cover to the air filter
compartment. The air filter is on the inside
of the cover. Press outward on the sides
of the central cover compartment to
release the tabs of the air filter. Remove
the air filter.
Install a new air filter.
BACK
1
2
After changing the filter, push and hold the
Fresh Filter button for three seconds to
reset the filter sensor.
ENGLISH
Replace the air filter:
48 MAINTENANCE
Replacing the Water Filter
ENGLISH
Note
2
Replace with a new water filter.
This refrigerator does not require a filter
bypass plug when the filter is not in place.
Insert the new filter into the filter head and
rotate it clockwise until the arrow on the
new filter lines up with the arrow on the
filter head. Swing the filter back into the
compartment.
3
Assemble the door bin.
After changing the filter, push and hold the
Water Filter button for three seconds to reset
the filter.
Replace the water filter:
yy
yy
yy
yy
Approximately every six months.
When the water filter indicator blinks.
When the water dispenser output decreases.
When the ice cubes are smaller than normal.
1
Remove the old water filter.
Lift up and remove the lower door bin. Swing
the right end of the water filter out of the
compartment and then grasp and rotate the
filter counterclockwise to remove it from the
filter head.
Note
Replacing the water filter could cause a
small amount of water to drain. Place a cup
under the filter head to catch any water.
MAINTENANCE 49
Performance Data Sheet
The concentration of the indicated substances in water entering the system was reduced to a
concentration less than or equal to the permissible limit for water leaving the system as specified in
NSF/ANSI Standard 42 and Standard 53.
System tested and certified by NSF International against NSF/ANSI Standard 42
and Standard 53 for the reduction of substances listed below.
Capacity 200 Gallons (757 Liters) Contaminant Reduction Determined by NSF testing.
Max
Average
Avg %
Permissible
Product Water
Reduction
Product Water
Concentration
Concentration
Contaminant
Reduction
Average
Influent
NSF specified
Challenge
Concentration
Chlorine Taste and
Odor
2.0 mg/L
2.0 mg/L ± 10%
97.5%
0.05 mg/L
N/A
≥ 50%
Nominal Particulate
Class I, , ≥ 0.5 to <
1.0 µm
5,600,000 pts/
mL
At least 10,000 particles/
mL
99.3%
73,000 pts/ml
N/A
≥ 85%
Asbestos
170 MFL
107 to 108 MFL; fibers
greater than 10 µm in
length
>99%
< 1MLF
N/A
≥ 99%
Atrazine
0.0087 mg/L
0.009 mg/L ± 10%
94.2%
0.0005 mg/L
0.003 mg/L
N/A
Benzene
0.017 mg/L
0.015 mg/L ± 10%
97.0%
< 0.0005 mg/L
0.005 mg/L
N/A
Carbofuran
0.073 mg/L
0.08 mg/L ± 10%
98.8%
0.001 mg/L
0.04 mg/L
N/A
Lindane
0.002 mg/L
0.002 mg/L ± 10%
98.8%
0.00002 mg/L
0.0002 mg/L
N/A
P-Dichlorobenzene
0.263 mg/L
0.225 mg/L ± 10%
99.6%
0.001 mg/L
0.075 mg/L
N/A
Toxaphene
0.015 mg/L
0.015 mg/L ± 10%
93.5%
0.001 mg/L
0.003 mg/L
N/A
2,4-D
0.25 mg/L
0.210 mg/L ± 10%
99.5%
0.0012 mg/L
0.07 mg/L
N/A
Lead pH @6.5
0.150 mg/L
0.15 mg/L ± 10%
>99.3%
0.001 mg/L
0.010 mg/L
N/A
Lead pH @8.5
0.150 mg/L
0.15 mg/L ± 10%
>99.3%
0.001 mg/L
0.010 mg/L
N/A
Mercury @ pH 6.5
0.006 mg/L
0.006 mg/L ± 10%
96.5
0.0002 mg/L
0.002 mg/L
N/A
Mercury @ pH 8.5
0.0062 mg/L
0.006 mg/L ± 10%
86.9
0.0081 mg/L
0.002 mg/L
N/A
200,000
cysts/L
Minimum 50,000 cysts/L
>99.99%
<1 cyst/L
N/A
≥ 99.95%
Cyst*
* Based on the use of Cryptosporidium parvum oocysts.
NSF Reduction
equirements
ENGLISH
Use Replacement Cartridge: ADQ73613401
50 MAINTENANCE
Application Guidelines / Water Supply Parameters
ENGLISH
Note that while the testing was performed under
standard laboratory conditions, actual performance
may vary.
Service Flow
0.5 gpm (1.9 lpm)
Water Supply
Community or private well
— Potable Water
Water Pressure
20 -120 psi (138 - 827 kPa)
Water Temperature
33-100°F (0.6 -37.8°C)
Capacity
200 gallons (757 liters)
NSF System Trade Name Code : ADQ73613401-S
NSF Replacement Code : ADQ73613401
It is essential that the manufacturer’s
recommended installation, maintenance and filter
replacement requirements be carried out for the
product to perform as advertised.
Replacement Cartridge: ADQ73613401
For estimated costs of replacement elements
please call 1-877-714-7486 or visit our website at
www.lg.com
Refer to the “warranty” section of the
Refrigerator Owner’s Manual for Limited Warranty
information.
SAFETY INFORMATION
Read, understand, and follow all safety Information contained in these instructions prior to installation and
use of this product. Retain these instructions for future reference.
Warning
To reduce the risk associated with the ingestion of contaminants:
yy Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. Systems certified for cyst reduction may be used on
disinfected water that may contain filterable cysts.
Caution
Please note that water could leak while replacing the filter which could result in property damage.
To reduce the risk associated with property damage due to water leakage:
yy Read and follow Use Instructions before installation and use of this system.
yy Installation must comply with existing state or local plumbing codes.
yy Protect filter from freezing Drain filter when room temperature drops below 33°F (0.6°C).
yy Do not install if water pressure exceeds 120 psi (827 kPa). If your water pressure exceeds 80 psi,
you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how
to check your water pressure.
yy Do not install where water hammer conditions may occur. If water hammer conditions exist you
must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to
check for this condition.
yy Do not install on hot water supply lines. Install on cold water lines only. The maximum operating
water temperature of this filter system is 100°F (37.8°C).
yy Where a backflow prevention device is installed on a water system, a device for controlling pressure
due to thermal expansion must be installed.
yy The disposable filter cartridge must be replaced every six months, at the rated capacity or if a
noticeable reduction in flow rate occurs.
NSF is a trademark of NSF International. LG is a trademark of LG Corp. MCM Co..Ltd.
MAINTENANCE
51
ENGLISH
California Department of Public Health Certification 14-3015
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement