Tauris CMW 297 flat panel wall mount Instruction manual

CMW - 297

Professional Installer Highly Recommended - The bracket manufacturer will not warrant any faulty installations, and damage to panels or any other fixtures / fittings as a result of incorrect installation.

STEP 1

Attach bracket to the wall.

STEP 2

Attach face plate to bracket.

1

IMPORTANT: PRE-DRILL HOLES

Make sure bracket is secured to stud, or anchors are used for brick or concrete.

9

5

6

Find stud and select position for bracket (1) on the wall.

Level bracket and mark holes with a pencil then drill pilot holes.

Using a socket wrench fix arm bracket to the wall with hex head screws

(5) and washers (9).

If fixing to brick or concrete use plastic anchors (7).

Cover screw with plastic cap (6).

11

1

13

4

10

Attach face plate (2) to arm bracket using the allen key (13), bolt (4) and black washers (10).

Securely tighten nut (4) using the wrench provided (12).

Clip cable saddle (11) onto base of arm.

10

10

4

9

12

2

5 10

6

STEP 3

Attach railings to back of the TV.

(M5, M6, M8)

3

Locate screw fixtures in the back of your TV and attach railings (3) using the screws provided.

The screw size required will vary on each TV so we have provided you with a range to choose from (M5, M6, M8).

Optional:

Insert spacers (8) or additional washers (9) if back of TV is not a flat.

(M5, M6, M8)

STEP 4

Hook TV onto face plate

Once the railings (3) are firmly attached to the TV, hook the railings onto the face plate (2) and secure into place using locking screws provided.

2

STEP 5

Adjusting tilt and roll.

ADJUST TILT HERE

3

3

You can easily adjust the tilt and roll of the TV by simply loosening the bolts in the centre of the face plate with the allen key provided (14).

Secure bolts tightly for a fixed position or leave slightly loosened for an adjustable platform.

ADJUST ROLL HERE

Note: Make sure all screws are firmly tightened after adjusting tilt and roll.

w w w . t a u r i s . c o m . a u

DISTRIBUTED BY RVM AUSTRALIA t: (08) 9417 9944 e: [email protected]

Mar 2012

CMW - 297

4.

5.

7.

11.

12.

13.

14.

10.

6.

8.

9.

PARTS DRAWN TO SCALE 1:1

M5 M6 M8

Spring

Washer x4

Spring

Washer x4

Spring

Washer x4

NOTE: Use spring washers when securing bolts. This will reduce the risk of bolts coming loose.

ADDITIONAL TOOLS REQUIRED

A drill will be required to drill pilot holes for the arm bracket.

Masonry Wall - 9mm bit

Studded Wall - 5mm bit

A socket wrench will be required wherever you see this icon.

Hex Socket - 13mm or 1/2”��

PARTS LIST

No. Part

1 Wall Bracket With Arm

2 Face Plate

3 Railings

4

5

Pivot Bolt & Nut

Hex Screw

6

7

Plastic Cap

Masonry Anchors

Qty

1

1

2

1

2

2

2

No. Part

8 Plastic Spacer L12.5

9

10

11

12

13

14

Washer Silver ø8 ø18

Washer Black ø6 ø18

Cable Saddle

Wrench

Allen No. 6

Allen No. 5

Qty

4

10

4

2

1

1

1 w w w . t a u r i s . c o m . a u

DISTRIBUTED BY RVM AUSTRALIA t: (08) 9417 9944 e: [email protected]

Mar 2012