SFP130304F0D – SFP Dual fibre 1310nm / 30km

SFP130304F0D – SFP Dual fibre 1310nm / 30km
Datasheet
SFP130304F0D_RevA
SFP130304F0D – SFP Dual fibre
1310nm / 30km / 4x Fibre Channel.
For your product safety, please read the following information carefully before any manipulation of the transceiver:
ESD
This transceiver is specified as ESD threshold 1kV for SFI pins and 2kV for all others electrical input pins, tested per MIL-STD-883G, Method 3015.4
/JESD22-A114-A (HBM). However, normal ESD precautions are still required during the handling of this module.
LASER SAFETY
This is a Class1 Laser Product according to IEC 60825-1:2007. This product complies with 21 CFR 1040.10 and 1040.11 except for deviations
pursuant to Laser Notice No. 50, dated (June 24, 2007).
The optical ports of the module need to be terminated with an optical connector or with a dust plug in order to avoid contamination.
1.
Overview
SFP130304F0D is a high performance transceiver module for 4x Fibre Channel data links over a singlemode fiber pair.
The maximum reach1 is 30km, for a 18dB end of life (EOL) power budget. The emitter is a 1310nm DFB laser, the receiver
a PIN photodiode.
This transceiver module is compliant with the Small Form-factor Pluggable (SFP) Multisource Agreement (MSA) and hot
pluggable. Always contact Skylane Optics commercial agents for compatibility with different equipment platforms.
2.
Features
• SFP Multi-Source Agreement compliant [INF-8074]
• Hot pluggable SFP footprint
• Serial ID functionality supported according to [SFF-8472]
• Class 1 laser safety standard IEC 60825 compliant
• Dual LC connector
• 1310nm DFB transmitter
• 30km point-to-point transmission on singlemode fibre
• 4x Fibre Channel compliant
• 2x Fibre Channel compliant
Figure 1. SFP Dual Fiber 1310nm
(non-binding illustration)
• 1x Fibre Channel compliant
• Gigabit Ethernet compatible
• Operating temperature range 0°C to 70°C
• Low power dissipation (<1W)
• Digital diagnostic monitoring (DDM)
3.
Applications
• Storage
• Gigabit Ethernet
4.
Optical Interface
P/N
Wavelength
[nm]
Output Optical
Power2
[dBm]
Optical Receiver
Sensitivity3
[dBm]
Optical Receiver
Overload4
[dBm]
Power Budget2
[dB]
SFP130304F0D
1310nm
0 to 5
≤ -18
-3
≥ 18
1.
2.
3.
4.
Distance is estimated assuming typical optical losses after decent quality fiber deployment; Only optical budget value is guaranteed.
EOL, over operating temperature range
Measured at 4x Fibre Channel
The optical input to the receiver should not exceed this value. Transmitters must never be directly connected to receivers (optical loop back) before ensuring that
proper optical attenuation is used.
Specification subject to change without notice
1
Datasheet
SFP130304F0D_RevA
5.
Technical parameters
5.1. Recommended Operating Conditions
Parameter
Min
Max
Units
Storage temperature
-40
85
°C
Operating Case Temperature
0
70
°C
Relative Humidity
5
95
%
Power Supply Voltage
3.15
Typ
3.3
Power Supply Current
Notes
Non condensing
3.45
V
300
mA
Max
Units
Notes
5
dBm
5
1330
nm
5.2. Transmitter Optical Specifications (0 to 70°C, 3.3V +/-5%)
Parameter
Min
Average Output Power
Typ
0
Center Wavelength
1290
1310
Complies with ANSI FC-PI
specification
Optical Extinction Ratio ER
Spectral Width
6
1
nm
Max
Units
Notes
-18
dBm
6
5. Output power coupled into a 9/125 µm single-mode fiber
5.3. Receiver Optical Specifications ( 0 to 70°C, 3.3V +/- 5%)
Parameter
Min
Typ
Sensitivity
Receiver Overload
-3
Wavelength of Operation
1500
dBm
1550
1600
nm
6. With BER better than or equal to 1x10-12, measured in the center of the eye opening with 27-1 PRBS
6.
Transceiver Electrical Pad Layout
Towards BEZEL ←
1
2
3
4
5
6
7
8
9
10
VeeT
Tx_Fault
Tx_Disable
SDA
SCL
MOD_ABS
RS0
Rx_LOS
RS1
VeeR
VeeT
TDTD+
VeeT
VccT
VccR
VeeR
RD+
RDVeeR
20
19
18
17
16
15
→ Towards ASIC
14
13
12
11
Figure 2. Transceiver Electrical Pad Layout
Specification subject to change without notice
2
Datasheet
SFP130304F0D_RevA
7.
Pin Functions Definitions
Pin
Number
8.
Name
Function
1
VeeT
Transmitter Ground
2
TX_Fault
Transmitter Fault Indication
3
TX_ Disable
Transmitter Disable
4
SDA
2-Wire Serial Interface Data (SDA)
5
SCL
2-Wire Serial Interface Clock (SCL)
6
MOD_ABS
Function Not available
7
RS0
Rate Select 0 grounded
8
Rx_LOS
Loss of signal
9
RS1
Rate select 1 grounded
10
VeeR
Receiver Ground
11
VeeR
Receiver Ground
12
RD-
Inverted received data output
13
RD+
Received data output
14
VeeR
Receiver Ground
15
VccR
Receiver Power
16
VccT
Transmitter Power
17
VeeT
Transmitter Ground
18
TD+
Transmit data input
19
TD-
Inverted transmit data input
20
VeeT
Transmitter Ground
EEPROM
SFP MSA [INF-8074]
2 wire address
1010000x
0
Serial ID Defined by
SFP MSA (96 bytes)
95
Vendor Specifics
(32 bytes)
127
Reserved
(128 bytes)
255
A0h
Figure 3. EEPROM of a SFP
Specification subject to change without notice
3
Datasheet
SFP130304F0D_RevA
9.
Ordering information
Part Number
Description
SFP130304F0D
SFP dual fibre, Tx 1310nm (DFB), Rx (PIN), maximum distance 30km,
power budget 18dB, 4x Fibre Channel, LC connector, 0°C to 70°C, DDM
Skylane Optics® supplies a broad range of optical
transceivers. Our engineers work closely with our
customers to find the best solutions for every
application. We are committed to provide high
quality products and services to our customers.
For questions on this product please contact:
support@skylaneoptics.com
Beyond
Quality
Reliable
Alliance
Performing
Smartly
Specification subject to change without notice
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising