Peavey Nashville 112 80-Watt 1x12 Pedal Steel Guitar Amp Operation Manual


Add to my manuals
12 Pages

advertisement

Peavey Nashville 112 80-Watt 1x12 Pedal Steel Guitar Amp Operation Manual | Manualzz

Nashville

112 Operation Manual

For more information on other great Peavey products, go to your local Peavey dealer or online at www.peavey.com.

Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

C AU TIIO N:: Risk of electrical shock — DO NOT OPEN!

C AU TIIO N:: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.

Refer servicing to qualified service personnel.

W AR NIIN G:: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture.

Before using this appliance, read the operating guide for further warnings.

Este símbolo tiene el propósito, de alertar al usuario de la presencia de “(voltaje) peligroso” sin aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para constituir riesgo de descarga eléctrica.

Este símbolo tiene el propósito de alertar al usario de la presencia de instruccones importantes sobre la operación y mantenimiento en la información que viene con el producto.

P RE AU

P RE AU dentro. Deje todo mantenimiento en manos del personal técnico cualificado.

A DV ER TE A:: Para evitar descargas eléctricas o peligro de incendio, no deje expuesto a la lluvia o humedad este aparato Antes de usar este aparato, Iea más advertencias en la guía de operación.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur la présence d’une tension dangereuse pouvant être d’amplitude suffisante pour constituer un risque de choc électrique.

Ce symbole est utilisé dans ce manuel pour indiquer à l’utilisateur qu’il ou qu’elle trouvera d’importantes instructions concernant l’utilisation et l’entretien de l’appareil dans le paragraphe signalé.

A TT EN TIIO

A TT EN TIIO l’intérieur aucune pièce pouvant être reparée par l’utilisateur. Confiez I’entretien et la réparation de l’appareil à un réparateur Peavey agréé.

A VE SS ME T: Afin de prévenir les risques de décharge électrique ou de feu, n’exposez pas cet appareil à la pluie ou à l’humidité. Avant d’utiliser cet appareil, lisez attentivement les avertissements supplémentaires de ce manuel.

Dieses Symbol soll den Anwender vor unisolierten gefährlichen Spannungen innerhalb des Gehäuses warnen, die von Ausreichender Stärke sind, um einen elektrischen Schlag verursachen zu können.

Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.

V OR SIIC T:: Risiko — Elektrischer Schlag! Nicht öffnen!

V OR SIIC T:: Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es befinden sich keine Teile darin, die vom Anwender repariert werden könnten. Reparaturen nur von qualifiziertem Fachpersonal durchführen lassen.

A CH UN

Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

2

IIM PO TA NT AFFE Y IIN RU TIIO S

W AR NIIN G:: When using electrical products, basic cautions should always be followed, including the following:

1.

Read these instructions.

2.

Keep these instructions.

3.

4.

5.

6.

7.

8.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

9.

Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.

11.

12.

13.

Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.

Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚ proceed as follows: a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚ colored green or colored green and yellow.

b) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black.

c) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

Only use attachments/accessories provided by the manufacturer.

Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

14.

15.

16.

17.

18.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.

If this product is to be mounted in an equipment rack, rear support should be provided.

Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:

Duration Per Day In Hours

4

3

8

6

2

1 1⁄2

1

1⁄2

1⁄4 or less

Sound Level dBA, Slow Response

90

92

95

97

100

102

105

110

115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.

S AV E T HE E IIN RU TIIO S!!

3

E NG H

Congatulations on your purchase of the Peavey Nashville 112. As the leader in steel guitar amplification, we are proud to offer you this smaller, more portable, lightweight cousin to the popular Nashville 1000 amplifier. This amp has all of the same front panel features as the 1000 along with a newly designed 80

Watt power section, an added headphone jack, and a CD input which makes it an ideal choice for practice or small venues. The Nashville 112 also features a long-pan Accutronics reverb and a newly designed 12"

Blue Marvel speaker that has been carefully voiced for steel guitar applications.

We know you are anxious to start playing, so we’ve included a “Quick Start” section and a

“Recommended Settings” section. These are certain to get you on your way. However, iitt iiss iim po ntt tth y ou d tth e ssa these safety icons: ecca uttiio

Each safety icon is followed by a warning. Read that warning carefully before continuing. Once you have read all of the warnings ,refer to the “Quick Start” section below if you so desire. It is recommended that you read this manual in its entirety to fully understand the functions of each feature.

Q uiicck arrtt -- II jju stt w nn plla y!!

The following section takes a “jump in and get your feet wet” approach. If any part seems confusing, refer to the more detailed sections that follow.

Step 1. Insure that you have read and understand all safety warnings noted through-out the manual. It is imperative that you follow these precautions for the safety of yourself and your amp.

Step 2. With the amp turned off, plug the power cord into the proper voltage supply indicated on the back of the unit near the cord retainer.

Step 3. Plug your guitar into either the High or Low Gain input and turn all knobs counterclockwise to their “0” position.

Step 4. Using the “Recommended Settings” on page 8, find the type of tone that most closely resembles the tone you wish to obtain.

Step 5. Set the knobs on the front of the unit to match the setting you have selected.

Step 6. Turn your guitar volume down and turn the amp on via the power switch on the back of the unit.

Step 7 Gradually turn the volume of your guitar all the way up or until you are comfortable with the level/tone.

Step 8 To adjust the overall level, use the Master Gain control.

Step 9. To adjust out any undesirable distortion, use the Pre Gain knob. Turning the knob counter-clockwise results in a decreased level, thus reducing the overdriven signal. Any external effects units can also cause the signal to overdrive.

Step 10. You should be able to play at this time. Vary the Reverb and/or EQ knobs to get a feel for their effect on your tone. Most importantly....R

EA D T HE RE ST OFF T HIIS NU ALL.

4

1 2 3

FFrro ntt P ell

4 5 6 5 7 8 9 10 11

Hiig h G n IIn utt

High Gain Input used for most electric guitars. It is 10 dB louder than the Low Gain input.

2)) LLo w G

Low Gain is provided for instruments that have extremely high outputs, which can result in overdriving (distorting) the High Gain input. If both inputs are used simultaneously, the output levels are the same (Both are low gain.).

Pre Gain controls the input level of the Nashville 112. Adjusting this control clockwise will increase the input level resulting in a hotter, more responsive signal.

e E Q P h ((V ollu Pe da

These 1/4" mono jacks allow for Pre EQ effects patching. Connect a quality shielded instrument cable between the “send” jack and the input of your external effects unit. Connect another quality shielded instrument cable from the output of your effects unit to the “return” jack. Pay attention to the external effects unit levels (input and output) to avoid distortion. Consult the owner’s manual for your effects unit. It should be noted that too strong a signal at the return jack can overdrive the EQ section of the Nashville 112. If this happens, the effects unit output should be reduced.

5)) LLo w,, M an d H h E

This section is an active tone control. Adjusting these knobs clockwise from the center (0) position will amplify the low, mid, or high frequency content. Adjusting counterclockwise from the center (0) position will attenuate the low, mid, or high frequency content.

6)) S hiifftt

The Shift knob changes the center frequency of the Mid EQ (5), allowing you to tailor the Nashville 112 EQ to accommodate your tone requirements. The center frequency can be adjusted from 150 Hz to 1.5 kHz. Keep in mind that the further you turn the knob away from a frequency, the less affect the Mid EQ will have on that frequency.

N e:: The shift and MID controls interact in determining the preferred mid-range settings.

esse e

Presence is an active tone control that boosts the extreme high frequencies up to 15 dB.

8)) P osstt E Q P h

Similar to the Pre EQ Patch(4), these jacks are post EQ. The same connections apply. The return level should still be monitored for its strength. In addition, the Post EQ Patch can be taken in and out of the signal path via the footswitch (not included).

9)) M asstte evve

Adjusting this control clockwise will result in more reverb content in the output of the amp. The reverb can be defeated by rotating the control counterclockwise or via the footswitch (not included).

5

12

M asstte aiin

The Master Gain controls the overall volume level of the amplifier. The final adjustment to this control should be made after the desired sound/tone has been achieved.

P ow err LLE D ((1111))

The Power LED illuminates when power is supplied to the amp. If this LED is lit, the amp is on.

R ea ne

13 14 15 16 17

2)) P ow err S h

Placing this switch in the “On” position will result in power being supplied to the unit. The Power LED (11) will illuminate when the amp is on.

3)) P ow err A mp

This mono 1/4" jack provides an input to the power amplifier. When used in conjunction with the Preamp Out jack

(14), an effects loop is formed allowing the use of external equalizers and effects.

Prre am p O utt // C D IIn utt

This mono 1/4" jack provides an output from the preamp. When used in conjunction with the Power Amp In jack

(13), an effects loop is formed allowing the use of external equalizers and effects. This jack can also be used to connect the output of a CD or tape player to the power amp for “play along” practicing. A shielded stereo cable should be used to connect to the CD input.

5)) LLiin e O

The Line Out XLR jack offers you a balanced, low impedance output to go to a mixing board or snake. This can help to eliminate mics on stage as well as loud levels. This results in less chance of feedback as well. Use quality mic cables to make this patch.

6)) H ea ho ne

A headphone jack is provided for stereo headphones. This switching jack disengages the internal speaker when plugged in.

7)) R em e S h

This jack is provided for the connection of the optional footswitch (part #90001791). The footswitch is a multifunction type, allowing you to to defeat the Reverb and/or the Post EQ Patch loop. To use the footswitch, insure that the footswitch plug is inserted fully into the jack.

R em ovva blle C P err C d

This receptacle is for the IEC line cord (included), which provides AC power to the unit. Connect the line cord to this connector and to a properly grounded AC supply. Damage to the equipment may occur if an improper line voltage is used (see voltage marking on unit). Never remove or cut the ground pin of the line cord plug. This unit is supplied with a properly rated line cord. When lost or damaged, replace this cord with one of the proper ratings.

6

Post-EQ Effects Loop

Switch Logic

Line Out

Pre Gain

7

4 Ohm Speaker

Master Gain

N AS E

S ET TIIN EX AM PL S

8

Left Mono Output

Left Mono Input

9

Signal From Instrument

N as e

S PE FIIC AT S

P ow err a mp eccttiio n::

R atte d p ow err a d llo d::

80 Watts RMS into 4 Ohms (with DDT ™ compression) eq ue essp on

+0, -3 dB, 20 Hz to 20 kHz @ 80 Watts

RMS into 4 Ohms

T otta arrm on orrttiio n::

Less than 0.3%, 1 Watt to 80 Watts RMS,

20 Hz to 20 kHz, 4 Ohms

D T d yn miicc rra

Greater than 20 dB e::

DD T m axxiim um D::

Below 0.8% THD for 6 dB overload

Below 3.5% THD for 20 dB overload

H um nd e::

Greater than 83 dB below rated power

P ow err cco um pttiio

200 Watts, 50/60 Hz, 120 VAC (domestic)

Prre am eccttiio n::

The following specs are measured @ 1kHz with the controls preset as follows:

Master gain @ 10

Low EQ @ 0 dB

Mid EQ @ 0 dB

Mid Shift @ 600 Hz

High EQ @ 0 dB

Presence EQ @ 0 dB

Reverb @ 0

Nominal levels are with pre gain @ 5

Minimum levels are with pre gain @ 10

Prre am hiig h g np utt ((n o p d))::

Impedance: High Z, 220 k Ohms

Nominal input level: -29.9 dBV, 32 mV RMS

Minimum input level: -53.2 dBV, 2.2 mV RMS

Maximum input level: 8 dBV, 2.5 V RMS

Prre am p LLo w G n IIn pu 0 d B p d))::

Impedance: High Z, 68k Ohms

Nominal input level: -19.9 dBV, 101 mV RMS

Minimum input level: -43.2 dBV, 6.9 mV RMS

Maximum input level: 18 dBV, 8 V RMS e E Q p en d::

Load impedance: 10k Ohms or greater

Nominal output level: -18.6 dBV, 117 mV RMS e E Q p

Impedance: High Z, 220 k Ohms

Designed Input Level: -18.6 dBV, 117 mV RMS

(Switching jack provides send to return connection when not used)

P osstt E Q p attcch en d::

Load impedance: 10 k Ohms or greater

Nominal output level: -14.1 dBV, 198 mV RMS

P osstt E Q p attcch

Impedance: High Z, 1 m Ohms

Designed Input Level: -14.1 dBV, 198 mV RMS

(Switching jack provides send to return connection when not used)

R lliin e o uttp utt::

Load impedance: 5 k Ohms or greater

Nominal output level: -3.1 dBV, 0.7 V RMS

Prre am p o uttp D iin utt::

Load impedance: 10 k Ohms or greater

Nominal output level: -3.1 dBV, 0.7 V RMS

Nominal CD Input Level: -3.1 dBV, 0.7 V RMS

(Stereo cable must be used for CD Input to function)

P ow err a mp utt::

Impedance: High Z, 27 k Ohms

Designed Input Level: -3.1 dBV, 0.7 V RMS

(Switching jack provides preamp output to power amp input connection when not used)

S ysstte m h um nd oiisse @ n om np utt

(20 Hz to 20 kHz unweighted)

Greater than 75 dB below rated power

E qu attiio n::

Low: +/-15 dB @ 45 Hz, shelving

Mid: +/-15 dB @ Mid Shift frequency, boost/cut

Mid Shift: 150 Hz to 1.5 kHz

High: +/-15 dB @ 6 kHz (special EQ)

Presence: +/-15 dB @ 10 kHz, shelving errn all ffo h ((p arrtt # 00 0117 911,, n ott iin de d)) ffu nccttiio

Select effects: Post EQ effects Loop defeat

Reverb: Reverb defeat

Diim en nss ((H

18.125" x 21.375" x 10.250" eiig htt::

42.3 lbs.

10

PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY

Effective Date: July 1, 1998

W ha s W arrrra y C ov

Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada.

W ha s W arrrra y D oe s N ott C err

The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer.

W ho s W arrrra

This Warranty protects only the original retail purchaser of the product.

H ow on g T hiis arrrra y L as

The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows:

Product Category

Guitars/Basses, Amplifiers, Pre-Amplifiers, Mixers, Electronic

Crossovers and Equalizers

Duration

Drums

Enclosures

Digital Effect Devices and Keyboard and MIDI Controllers

Microphones

2 years *(+ 3 years)

2 years *(+ 1 year)

3 years *(+ 2 years)

1 year *(+ 1 year)

2 years

Speaker Components (incl. speakers, baskets, drivers, diaphragm replacement kits and passive crossovers) and all Accessories 1 year

Tubes and Meters 90 days

[*Denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase.]

W ha ea ve y W o

We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to

Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges.

H ow o G ett W arrrra y S errv

((11)) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center.

OR

Canada Ltd., 95 Shields Court, Markham, Ontario, Canada L3R 9T5. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage. Also provide a complete return address.

attiio n o plliie d W arrrra nttiie s

ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE

LENGTH OF THIS WARRANTY.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

E xccllu Da ma ge s

PEAVEY'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PEAVEY'S OPTION. IF WE ELECT TO

REPLACE THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PEAVEY SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF

USE, LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL,

CONSEQUENTIAL OR OTHERWISE, EVEN IF PEAVEY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service Center, please contact the Peavey

International Service Center at (601) 483-5365 / Peavey Canada Ltd. at (905) 475-2578.

Features and specifications subject to change without notice.

11

©2003

Features and specifications subject to change without notice.

Peavey Electronics Corporation • 711 A Street • Meridian, MS 39301

(601) 483-5365 • FAX (601) 486-1278 • www.peavey.com

80304961

Printed in the U.S.A. 5/03

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 80 watts of power
  • 2 channels with dedicated EQ
  • Built-in reverb
  • 12-inch speaker
  • Compact and lightweight
  • Durable construction
  • Affordable price

Related manuals

Frequently Answers and Questions

What is the power output of the Nashville 112?
80 watts
How many channels does the Nashville 112 have?
2
Does the Nashville 112 have reverb?
Yes
What is the speaker size of the Nashville 112?
12 inches
Is the Nashville 112 portable?
Yes, it is compact and lightweight
Is the Nashville 112 durable?
Yes, it has a durable construction
Is the Nashville 112 affordable?
Yes, it is priced affordably

advertisement