Intel Quad-Core Xeon 5300 Series Datasheet

Quad-Core Intel® Xeon® Processor
5300 Series
Datasheet
September 2007
Order Number: 315569-003
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,
BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS
PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER,
AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING
LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY
PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Intel products are not intended for use in medical, life saving,
life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked “reserved” or “undefined.” Intel
reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to them.
The Quad-Core Intel® Xeon® Processor 5300 Series may contain design defects or errors known as errata which may cause the
product to deviate from published specifications. Current characterized errata are available on request.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Intel® 64 architecture requires a computer system with a processor, chipset, BIOS, OS, device drivers and applications enabled for
Intel® 64. Processor will not operate (including 32-bit operation) without an Intel EM64T-enabled BIOS. Performance will vary
depending on your hardware and software configurations. Intel EM64T-enabled OS, BIOS, device drivers and applications may not
be available. Check with your vendor for more information.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature may be
obtained by calling 1-800-548-4725 or by visiting Intel's website at http://www.intel.com.
Intel, Pentium, Intel Xeon, Enhanced Intel SpeedStep Technology, Intel NetBurst and the Intel logo are trademarks of Intel
Corporation in the U.S. and other countries.
* Other names and brands may be claimed as the property of others.
Copyright © 2005-2007, Intel Corporation
2
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Contents
1
Introduction............................................................................................................... 11
1.1
Terminology ..................................................................................................... 13
1.2
State of Data .................................................................................................... 15
1.3
References ....................................................................................................... 15
2
Electrical Specifications ............................................................................................... 17
2.1
Front Side Bus and GTLREF ................................................................................ 17
2.2
Power and Ground Lands.................................................................................... 18
2.3
Decoupling Guidelines ........................................................................................ 18
2.3.1 VCC Decoupling...................................................................................... 18
2.3.2 VTT Decoupling ...................................................................................... 18
2.3.3 Front Side Bus AGTL+ Decoupling ............................................................ 19
2.4
Front Side Bus Clock (BCLK[1:0]) and Processor Clocking ....................................... 19
2.4.1 Front Side Bus Frequency Select Signals (BSEL[2:0]) .................................. 20
2.4.2 PLL Power Supply ................................................................................... 21
2.5
Voltage Identification (VID) ................................................................................ 21
2.6
Reserved, Unused, or Test Signals ....................................................................... 23
2.7
Front Side Bus Signal Groups .............................................................................. 24
2.8
CMOS Asynchronous and Open Drain Asynchronous Signals .................................... 26
2.9
Test Access Port (TAP) Connection....................................................................... 26
2.10 Platform Environmental Control Interface (PECI) DC Specifications........................... 26
2.10.1 DC Characteristics .................................................................................. 26
2.10.2 Input Device Hysteresis .......................................................................... 27
2.11 Mixing Processors.............................................................................................. 27
2.12 Absolute Maximum and Minimum Ratings ............................................................. 28
2.13 Processor DC Specifications ................................................................................ 29
2.13.1 Flexible Motherboard Guidelines (FMB) ...................................................... 29
2.13.2 VCC Overshoot Specification .................................................................... 42
2.13.3 Die Voltage Validation ............................................................................. 43
2.14 AGTL+ FSB Specifications................................................................................... 43
3
Mechanical Specifications............................................................................................. 47
3.1
Package Mechanical Drawings ............................................................................. 47
3.2
Processor Component Keepout Zones................................................................... 51
3.3
Package Loading Specifications ........................................................................... 51
3.4
Package Handling Guidelines............................................................................... 52
3.5
Package Insertion Specifications.......................................................................... 52
3.6
Processor Mass Specifications ............................................................................. 52
3.7
Processor Materials............................................................................................ 52
3.8
Processor Markings............................................................................................ 53
3.9
Processor Land Coordinates ................................................................................ 53
4
Land Listing ............................................................................................................... 57
4.1
Quad-Core Intel® Xeon® Processor 5300 Series Pin Assignments ........................... 57
4.1.1 Land Listing by Land Name ...................................................................... 57
4.1.2 Land Listing by Land Number ................................................................... 69
5
Signal Definitions ....................................................................................................... 79
5.1
Signal Definitions .............................................................................................. 79
6
Thermal Specifications ................................................................................................ 87
6.1
Package Thermal Specifications ........................................................................... 87
6.1.1 Thermal Specifications ............................................................................ 87
6.2
...................................................................................................................... 95
6.2.1 Thermal Metrology ................................................................................. 97
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
3
6.3
6.4
Processor Thermal Features ................................................................................ 98
6.3.1 Thermal Monitor Features........................................................................ 98
6.3.2 Thermal Monitor (TM1) ........................................................................... 98
6.3.3 Thermal Monitor 2 .................................................................................. 99
6.3.4 On-Demand Mode ................................................................................ 100
6.3.5 PROCHOT# Signal ................................................................................ 101
6.3.6 FORCEPR# Signal................................................................................. 101
6.3.7 THERMTRIP# Signal ............................................................................. 102
Platform Environment Control Interface (PECI) .................................................... 102
6.4.1 Introduction ........................................................................................ 102
6.4.2 PECI Specifications ............................................................................... 103
7
Features.................................................................................................................. 105
7.1
Power-On Configuration Options........................................................................ 105
7.2
Clock Control and Low Power States .................................................................. 105
7.2.1 Normal State ....................................................................................... 106
7.2.2 HALT or Extended HALT State ................................................................ 106
7.2.3 Stop-Grant State.................................................................................. 108
7.2.4 Extended HALT Snoop or HALT Snoop State, Stop Grant
Snoop State ........................................................................................ 109
7.3
Enhanced Intel SpeedStep® Technology ............................................................ 109
8
Boxed Processor Specifications ................................................................................... 111
8.1
Introduction ................................................................................................... 111
8.2
Mechanical Specifications ................................................................................. 113
8.2.1 Boxed Processor Heat Sink Dimensions (CEK) .......................................... 113
8.2.2 Boxed Processor Heat Sink Weight.......................................................... 121
8.2.3 Boxed Processor Retention Mechanism and Heat Sink
Support (CEK) ..................................................................................... 121
8.3
Electrical Requirements .................................................................................... 121
8.3.1 Fan Power Supply (Active CEK) .............................................................. 121
8.3.2 Boxed Processor Cooling Requirements ................................................... 122
8.4
Boxed Processor Contents ................................................................................ 123
9
Debug Tools Specifications......................................................................................... 125
9.1
Debug Port System Requirements ..................................................................... 125
9.2
Target System Implementation ......................................................................... 125
9.2.1 System Implementation ........................................................................ 125
9.3
Logic Analyzer Interface (LAI) ........................................................................... 125
9.3.1 Mechanical Considerations ..................................................................... 126
9.3.2 Electrical Considerations........................................................................ 126
Figures
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
4
Input Device Hysteresis ..................................................................................... 27
Quad-Core Intel® Xeon® Processor E5300 Series Load Current versus Time............. 32
Quad-Core Intel® Xeon® Processor X5300 Series and
Load Current versus Time................................................................................... 32
Quad-Core Intel® Xeon® Processor X5365 Series Load Current versus Time ............ 33
Quad-Core Intel® Xeon® Processor L5300 Series Load Current versus Time ............. 33
Quad-Core Intel® Xeon® Processor L5318 Load Current versus Time ...................... 34
Quad-Core Intel® Xeon® Processor E5300 Series VCC Static and
Transient Tolerance Load Lines........................................................................... 35
Quad-Core Intel® Xeon® Processor X5300 Series VCC Static and
Transient Tolerance Load Lines ........................................................................... 36
Quad-Core Intel® Xeon® Processor L5300 Series VCC Static and
Transient Tolerance Load Lines........................................................................... 37
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
2-10 Quad-Core Intel® Xeon® Processor X5365 Series VCC Static and
Transient Tolerance Load Lines ........................................................................... 39
2-11 Quad-Core Intel® Xeon® Processor L5318 VCC Static and
Transient Tolerance Load Lines ........................................................................... 41
2-12 VCC Overshoot Example Waveform...................................................................... 43
2-13 Electrical Test Circuit ......................................................................................... 45
2-14 TCK Clock Waveform ......................................................................................... 45
2-15 Differential Clock Waveform................................................................................ 46
2-16 Differential Clock Crosspoint Specification............................................................. 46
3-1
Processor Package Assembly Sketch .................................................................... 47
3-2
Processor Package Drawing (Sheet 1 of 3) ............................................................ 48
3-3
Processor Package Drawing (Sheet 2 of 3) ............................................................ 49
3-4
Processor Package Drawing (Sheet 3 of 3) ............................................................ 50
3-5
Processor Top-side Markings (Example)................................................................ 53
3-6
Processor Land Coordinates, Top View.................................................................. 54
3-7
Processor Land Coordinates, Bottom View............................................................. 55
6-1
Quad-Core Intel® Xeon® Processor E5300 Series Thermal Profile ........................... 90
6-2
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profiles .......................... 91
6-3
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Profile ........................... 93
6-4
Quad-Core Intel® Xeon® Processor L5300 Series Thermal Profile............................ 95
6-5
Quad-Core Intel® Xeon® Processor L5318 Thermal Profile ..................................... 96
6-6
Case Temperature (TCASE) Measurement Location ................................................ 98
6-7
Thermal Monitor 2 Frequency and Voltage Ordering ............................................. 100
6-8
PECI Topology ................................................................................................ 102
6-9
Conceptual Fan Control Diagram For A PECI-Based Platform.................................. 103
7-1
Stop Clock State Machine ................................................................................. 108
8-1
Boxed Quad-Core Intel® Xeon® Processor 5300 Series 1U Passive/3U+
Active Combination Heat Sink (With Removable Fan) ........................................... 111
8-2
Boxed Quad-Core Intel® Xeon® Processor 5300 Series
2U Passive Heat Sink ....................................................................................... 112
8-3
2U Passive Quad-Core Intel® Xeon® Processor 5300 Series Processor
Thermal Solution (Exploded View) ..................................................................... 112
8-4
Top Side Board Keepout Zones (Part 1) .............................................................. 114
8-5
Top Side Board Keepout Zones (Part 2) .............................................................. 115
8-6
Bottom Side Board Keepout Zones..................................................................... 116
8-7
Board Mounting-Hole Keepout Zones ................................................................. 117
8-8
Volumetric Height Keep-Ins .............................................................................. 118
8-9
4-Pin Fan Cable Connector (For Active CEK Heat Sink) ......................................... 119
8-10 4-Pin Base Board Fan Header (For Active CEK Heat Sink)...................................... 120
8-11 Fan Cable Connector Pin Out for 4-Pin Active CEK Thermal Solution ....................... 122
Tables
1-1
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
Quad-Core Intel® Xeon® Processor 5300 Series Features ...................................... 12
Core Frequency to FSB Multiplier Configuration ..................................................... 20
BSEL[2:0] Frequency Table ................................................................................ 20
Voltage Identification Definition........................................................................... 22
Loadline Selection Truth Table for LL_ID[1:0] ....................................................... 23
Market Segment Selection Truth Table for MS_ID[1:0] ........................................... 23
FSB Signal Groups............................................................................................. 24
AGTL+ Signal Description Table........................................................................... 25
Non AGTL+ Signal Description Table .................................................................... 25
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
5
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
3-1
3-2
3-3
4-1
4-2
5-1
6-1
6-2
6-3
6-4
6-5
6-6
6-7
6-8
6-9
6-10
6-11
6-12
6-13
7-1
7-2
8-1
8-2
8-3
6
Signal Reference Voltages .................................................................................. 25
PECI DC Electrical Limits .................................................................................... 26
Processor Absolute Maximum Ratings................................................................... 28
Voltage and Current Specifications....................................................................... 29
VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
E5300 Series, Quad-Core Intel® Xeon® Processor X5300 Series,
Quad-Core Intel® Xeon® Processor L5300 Series ................................................. 34
VCC Static and Transient Tolerance for Quad-Core Intel® Xeon®
Processor X5365 Series...................................................................................... 37
VCC Static and Transient Tolerance for Quad-Core Intel® Xeon®
Processor L5318 Series ..................................................................................... 40
AGTL+ Signal Group Specifications ...................................................................... 41
CMOS Signal Input/Output Group and TAP Signal Group DC Specifications ................ 42
Open Drain Output Signal Group DC Specifications ................................................ 42
VCC Overshoot Specifications.............................................................................. 42
AGTL+ Bus Voltage Definitions ............................................................................ 44
FSB Differential BCLK Specifications..................................................................... 44
Package Loading Specifications ........................................................................... 51
Package Handling Guidelines............................................................................... 52
Processor Materials............................................................................................ 52
Land Listing by Land Name ................................................................................. 57
Land Listing by Land Number .............................................................................. 69
Signal Definitions .............................................................................................. 79
Quad-Core Intel® Xeon® Processor E5300 Series Thermal Specifications ................. 89
Quad-Core Intel® Xeon® Processor E5300 Series Thermal Profile Table ................... 90
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Specifications ................. 91
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile A Table ................ 92
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile B Table ................ 92
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Specifications ................. 93
Quad-Core Intel® Xeon® Processor X5365 Series
Thermal Profile (Sheet 1 of 2) ............................................................................ 94
Quad-Core Intel® Xeon® Processor L5300 Series Thermal Specifications ................. 94
Quad-Core Intel® Xeon® Processor L5300 Series Thermal Profile............................ 95
Quad-Core Intel® Xeon® Processor L5318 Thermal Specifications ........................... 95
Quad-Core Intel® Xeon® Processor L5318 Nominal Thermal Profile ......................... 97
Quad-Core Intel® Xeon® Processor L5318 Short Term Thermal Profile .................... 97
GetTemp0() and GetTemp1() Error Codes .......................................................... 104
Power-On Configuration Option Lands ................................................................ 105
Extended HALT Maximum Power........................................................................ 107
PWM Fan Frequency Specifications for 4-Pin Active CEK Thermal Solution ............... 122
Fan Specifications for 4-Pin Active CEK Thermal Solution ...................................... 122
Fan Cable Connector Pin Out for 4-Pin Active CEK Thermal Solution ....................... 122
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Revision History
Revision
001
Description
Date
Initial Release
November 2006
002
Added Quad-Core Intel® Xeon® Processor L5300 Series
003
Included the G-step information. Added the Quad-Core Intel® Xeon®
Processor L5318.
March 2007
September 2007
§
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
7
8
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Introduction
1
Introduction
The Quad-Core Intel® Xeon® Processor 5300 Series are 64-bit server/workstation
processors utilizing four Intel Core™ microarchitecture cores. These processors are
based on Intel’s 65 nanometer process technology combining high performance with
the power efficiencies of low-power Intel Core™ microarchitecture cores. The QuadCore Intel® Xeon® Processor 5300 Series consists of two die, each containing two
processor cores. All processors maintain the tradition of compatibility with IA-32
software. Some key features include on-die, 32 KB Level 1 instruction data caches per
core and 4 MB shared Level 2 cache per die (8 MB Total Cache per processor) with
Advanced Transfer Cache Architecture. The processor’s Data Prefetch Logic
speculatively fetches data to the L2 cache before an L1 cache requests occurs, resulting
in reduced bus cycle penalties and improved performance. The 1333 MHz Front Side
Bus (FSB) is a quad-pumped bus running off a 333 MHz system clock, which results in
10.6 GBytes per second data transfer. The 1066 MHz Front Side Bus is based on a 266
MHz system clock for an 8.5 GBytes per second data transfer rate. The Quad-Core
Intel® Xeon® Processor X5300 Series offers higher clock frequencies than the
Quad-Core Intel® Xeon® Processor E5300 Series for platforms that are targeted for
the performance optimized segment. The Quad-Core Intel® Xeon® Processor L5300
Series is a lower voltage, lower power processor intended for ultra dense platforms.
Enhanced thermal and power management capabilities are implemented including
Thermal Monitor 1 (TM1), Thermal Monitor 2 (TM2) and Enhanced Intel SpeedStep®
Technology. TM1 and TM2 provide efficient and effective cooling in high temperature
situations. Enhanced Intel SpeedStep® Technology provides power management
capabilities to servers and workstations.
The Quad-Core Intel® Xeon® Processor 5300 Series features include Advanced
Dynamic Execution, enhanced floating point and multi-media units, Streaming SIMD
Extensions 2 (SSE2) and Streaming SIMD Extensions 3 (SSE3). Advanced Dynamic
Execution improves speculative execution and branch prediction internal to the
processor. The floating point and multi-media units include 128-bit wide registers and a
separate register for data movement. SSE3 instructions provide highly efficient doubleprecision floating point, SIMD integer, and memory management operations.
The Quad-Core Intel® Xeon® Processor 5300 Series supports Intel® 64 architecture
as an enhancement to Intel's IA-32 architecture. This enhancement allows the
processor to execute operating systems and applications written to take advantage of
the 64-bit extension technology. Further details on Intel 64 architecture and its
programming model can be found in the Intel® 64 and IA-32 Architecture Software
Developer's Manual.
In addition, the Quad-Core Intel® Xeon® Processor 5300 Series supports the Execute
Disable Bit functionality. When used in conjunction with a supporting operating system,
Execute Disable allows memory to be marked as executable or non executable. This
feature can prevent some classes of viruses that exploit buffer overrun vulnerabilities
and can thus help improve the overall security of the system. Further details on
Execute Disable can be found at http://www.intel.com/cd/ids/developer/
asmo-na/eng/149308.htm.
The Quad-Core Intel® Xeon® Processor 5300 Series supports Intel® Virtualization
Technology for hardware-assisted virtualization within the processor. Intel Virtualization
Technology is a set of hardware enhancements that can improve virtualization
solutions. Intel Virtualization Technology is used in conjunction with Virtual Machine
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
11
Introduction
Monitor software enabling multiple, independent software environments inside a single
platform. Further details on Intel Virtualization Technology can be found at
http://developer.intel.com/technology/vt.
The Quad-Core Intel® Xeon® Processor 5300 Series are intended for high performance
server and workstation systems. The processors support a Dual Independent Bus (DIB)
architecture with one processor on each bus, up to two processor sockets in a system.
The DIB architecture provides improved performance by allowing increased FSB speeds
and bandwidth. The processors will be packaged in an FC-LGA6 Land Grid Array
package with 771 lands for improved power delivery. It utilizes a surface mount
LGA771 socket that supports Direct Socket Loading (DSL).
Table 1-1.
Quad-Core Intel® Xeon® Processor 5300 Series Features
# of Processor
Cores
L1 Cache (per
core)
L2 Advanced
Transfer Cache
Front Side Bus
Frequency
Package
4
32 KB instruction
32 KB data
4MB Shared L2
Cache per die
8MB Total Cache
1333 MHz
1066 MHz
FC-LGA6
771 Lands
Quad-Core Intel® Xeon® Processor 5300 Series based platforms implement
independent core voltage (VCC) power planes for each processor. FSB termination
voltage (VTT) is shared and must connect to all FSB agents. The processor core voltage
utilizes power delivery guidelines specified by VRM/EVRD 11.0 and its associated load
line (see Voltage Regulator Module (VRM) and Enterprise Voltage Regulator-Down
(EVRD) 11.0 Design Guidelines for further details). VRM/EVRD 11.0 will support the
power requirements of all frequencies of the processors including Flexible Motherboard
Guidelines (FMB) (see Section 2.13.1). Refer to the appropriate platform design
guidelines for implementation details.
The Quad-Core Intel® Xeon® Processor 5300 Series support 1333, or 1066 MHz Front
Side Bus operation. The FSB utilizes a split-transaction, deferred reply protocol and
Source-Synchronous Transfer (SST) of address and data to improve performance. The
processor transfers data four times per bus clock (4X data transfer rate, as in AGP 4X).
Along with the 4X data bus, the address bus can deliver addresses two times per bus
clock and is referred to as a ‘double-clocked’ or a 2X address bus. In addition, the
Request Phase completes in one clock cycle. Working together, the 4X data bus and 2X
address bus provide a data bus bandwidth of up to 10.66 GBytes (1333 MHz), or 8.5
GBytes (1066 MHz) per second. The FSB is also used to deliver interrupts.
Signals on the FSB use Assisted Gunning Transceiver Logic (AGTL+) level voltages.
Section 2.1 contains the electrical specifications of the FSB while implementation
details are fully described in the appropriate platform design guidelines (refer to
Section 1.3).
12
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Introduction
1.1
Terminology
A ‘#’ symbol after a signal name refers to an active low signal, indicating a signal is in
the asserted state when driven to a low level. For example, when RESET# is low, a
reset has been requested. Conversely, when NMI is high, a nonmaskable interrupt has
occurred. In the case of signals where the name does not imply an active state but
describes part of a binary sequence (such as address or data), the ‘#’ symbol implies
that the signal is inverted. For example, D[3:0] = ‘HLHL’ refers to a hex ‘A’, and
D[3:0]# = ‘LHLH’ also refers to a hex ‘A’ (H= High logic level, L= Low logic level).
Commonly used terms are explained here for clarification:
• Quad-Core Intel® Xeon® Processor 5300 Series – Intel 64-bit microprocessor
intended for dual processor servers and workstations. The Quad-Core Intel®
Xeon® Processor 5300 Series is based on Intel’s 65 nanometer process, in the
FC-LGA6 package with four processor cores. For this document, “processor” is used
as the generic term for the “Quad-Core Intel® Xeon® Processor 5300 Series”. The
term ‘processors’ and “Quad-Core Intel® Xeon® Processor 5300 Series” are
inclusive of Quad-Core Intel® Xeon® Processor E5300 Series, Quad-Core Intel®
Xeon® Processor X5300 Series and Quad-Core Intel® Xeon® Processor L5300
Series.
• Quad-Core Intel® Xeon® Processor E5300 Series – A mainstream
performance version of the Quad-Core Intel® Xeon® Processor 5300 Series. For
this document “Quad-Core Intel® Xeon® Processor E5300 Series” is used to call
out specifications that are unique to the Quad-Core Intel® Xeon® Processor E5300
Series SKU.
• Quad-Core Intel® Xeon® Processor X5300 Series – An accelerated
performance version of the Quad-Core Intel® Xeon® Processor 5300 Series. For
this document “Quad-Core Intel® Xeon® Processor X5300 Series” is used to call
out specifications that are unique to the Quad-Core Intel® Xeon® Processor X5300
Series SKU.
• Quad-Core Intel® Xeon® Processor X5365 Series– An ultra performance
version of the Quad-Core Intel® Xeon® Processor 5300 Series. For this document
“Quad-Core Intel® Xeon® Processor X5365 Series” is used to call out
specifications that are unique to the Quad-Core Intel® Xeon® Processor X5365
Series SKU.
• Quad-Core Intel® Xeon® Processor L5300 Series - Intel 64-bit
microprocessor intended for dual processor server blades and embedded servers.
The Quad-Core Intel® Xeon® Processor L5300 Series is a lower voltage, lower
power version of the Quad-Core Intel® Xeon® Processor 5300 Series. For this
document “Quad-Core Intel® Xeon® Processor L5300 Series” is used to call out
specifications that are unique to the Quad-Core Intel® Xeon® Processor L5300
Series.
• Quad-Core Intel® Xeon® Processor L5318 - Intel 64-bit microprocessor
intended for dual processor server blades and embedded servers requiring higher
case temperatures. The Quad-Core Intel® Xeon® Processor L5318 is a lower
voltage, lower power version of the Quad-Core Intel® Xeon® Processor 5300
Series. For this document “Quad-Core Intel® Xeon® Processor L5318” is used to
call out specifications that are unique to the Quad-Core Intel® Xeon® Processor
L5318 SKU.
• FC-LGA6 (Flip Chip Land Grid Array) Package – The Quad-Core Intel® Xeon®
Processor 5300 Series package is a Land Grid Array, consisting of a processor core
mounted on a pinless substrate with 771 lands, and includes an integrated heat
spreader (IHS).
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
13
Introduction
• LGA771 socket – The Quad-Core Intel® Xeon® Processor 5300 Series interfaces
to the baseboard through this surface mount, 771 Land socket. See the LGA771
Socket Design Guidelines for details regarding this socket.
• Processor core – Processor core with integrated L1 cache. L2 cache and system
bus interface are shared between the two cores on the die. All AC timing and signal
integrity specifications are at the pads of the processor die.
• FSB (Front Side Bus) – The electrical interface that connects the processor to the
chipset. Also referred to as the processor system bus or the system bus. All
memory and I/O transactions as well as interrupt messages pass between the
processor and chipset over the FSB.
• Dual Independent Bus (DIB) – A front side bus architecture with one processor
on each bus, rather than a FSB shared between two processor agents. The DIB
architecture provides improved performance by allowing increased FSB speeds and
bandwidth.
• Flexible Motherboard Guidelines (FMB) – Are estimates of the maximum
values the Quad-Core Intel® Xeon® Processor 5300 Series will have over certain
time periods. The values are only estimates and actual specifications for future
processors may differ.
• Functional Operation – Refers to the normal operating conditions in which all
processor specifications, including DC, AC, FSB, signal quality, mechanical and
thermal are satisfied.
• Storage Conditions – Refers to a non-operational state. The processor may be
installed in a platform, in a tray, or loose. Processors may be sealed in packaging or
exposed to free air. Under these conditions, processor lands should not be
connected to any supply voltages, have any I/Os biased or receive any clocks.
Upon exposure to “free air” (that is, unsealed packaging or a device removed from
packaging material) the processor must be handled in accordance with moisture
sensitivity labeling (MSL) as indicated on the packaging material.
• Priority Agent – The priority agent is the host bridge to the processor and is
typically known as the chipset.
• Symmetric Agent – A symmetric agent is a processor which shares the same I/O
subsystem and memory array, and runs the same operating system as another
processor in a system. Systems using symmetric agents are known as Symmetric
Multiprocessing (SMP) systems.
• Integrated Heat Spreader (IHS) – A component of the processor package used
to enhance the thermal performance of the package. Component thermal solutions
interface with the processor at the IHS surface.
• Thermal Design Power – Processor thermal solutions should be designed to meet
this target. It is the highest expected sustainable power while running known
power intensive real applications. TDP is not the maximum power that the
processor can dissipate.
• Intel® 64 Architecture – Instruction set architecture and programming
environment of Intel’s 64-bit processors, which are a superset of and compatible
with IA-32. This 64-bit instruction set architecture was formerly known as IA-32
with EM64T or Intel® EM64T.
• Enhanced Intel SpeedStep® Technology – Technology that provides power
management capabilities to servers and workstations.
• Platform Environment Control Interface (PECI) – A proprietary one-wire bus
interface that provides a communication channel between Intel processor and
chipset components to external thermal monitoring devices, for use in fan speed
control. PECI communicates readings from the processor’s Digital Thermal Sensor
(DTS). The replaces the thermal diode available in previous processors.
14
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Introduction
• Intel® Virtualization Technology (Intel® VT) – Processor virtualization which
when used in conjunction with Virtual Machine Monitor software enables multiple,
robust independent software environments inside a single platform.
• VRM (Voltage Regulator Module) – DC-DC converter built onto a module that
interfaces with a card edge socket and supplies the correct voltage and current to
the processor based on the logic state of the processor VID bits.
• EVRD (Enterprise Voltage Regulator Down) – DC-DC converter integrated onto
the system board that provides the correct voltage and current to the processor
based on the logic state of the processor VID bits.
• VCC – The processor core power supply.
• VSS – The processor ground.
• VTT – FSB termination voltage. (Note: In some Intel processor EMTS documents,
VTT is instead called VCCP.)
1.2
State of Data
The data contained within this document is the most accurate information available by
the publication date of this document.
1.3
References
Material and concepts available in the following documents may be beneficial when
reading this document:
Document
AP-485, Intel® Processor Identification and the CPUID Instruction
Intel®
Intel®
Intel®
Intel®
Intel®
64
64
64
64
64
and
and
and
and
and
IA-32
IA-32
IA-32
IA-32
IA-32
Architectures
Architectures
Architectures
Architectures
Architectures
Software
Software
Software
Software
Software
Developer’s
Developer’s
Developer’s
Developer’s
Developer’s
Manual,
Manual,
Manual,
Manual,
Manual,
Volume
Volume
Volume
Volume
Volume
IA-32 Intel® Architecture Optimization Reference Manual
Quad-Core Intel® Xeon® Processor 5300 Series Specification Update
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
1
2A
2B
3A
3B
Document
Number1
Notes
241618
2
253665
253666
253667
253668
253669
2
248966
2
3
15
Introduction
Document
Number1
Document
Notes
Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design
Guidelines
Clovertown Processor Boundary Scan Descriptive Language (BSDL) Model
Debug Port Design Guide for UP/DP Systems
10
1
Notes: Contact your Intel representative for the latest revision of these documents.
§
16
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
2
Electrical Specifications
2.1
Front Side Bus and GTLREF
Most Quad-Core Intel® Xeon® Processor 5300 Series FSB signals use Assisted
Gunning Transceiver Logic (AGTL+) signaling technology. This technology provides
improved noise margins and reduced ringing through low voltage swings and controlled
edge rates. AGTL+ buffers are open-drain and require pull-up resistors to provide the
high logic level and termination. AGTL+ output buffers differ from GTL+ buffers with
the addition of an active PMOS pull-up transistor to “assist” the pull-up resistors during
the first clock of a low-to-high voltage transition. Platforms implement a termination
voltage level for AGTL+ signals defined as VTT. Because platforms implement separate
power planes for each processor (and chipset), separate VCC and VTT supplies are
necessary. This configuration allows for improved noise tolerance as processor
frequency increases. Speed enhancements to data and address buses have made
signal integrity considerations and platform design methods even more critical than
with previous processor families. Design guidelines for the processor FSB are detailed
in the appropriate platform design guidelines (refer to Section 1.3).
The AGTL+ inputs require reference voltages (GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID and GTLREF_ADD_END) which are used by the receivers to
determine if a signal is a logical 0 or a logical 1. GTLREF_DATA_MID and
GTLREF_DATA_END are used for the 4X front side bus signaling group and
GTLREF_ADD_MID and GTLREF_ADD_END are used for the 2X and common clock front
side bus signaling groups. GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID, and GTLREF_ADD_END must be generated on the baseboard (See
Table 2-20 for GTLREF_DATA_MID, GTLREF_DATA_END, GTLREF_ADD_MID and
GTLREF_ADD_END specifications). Refer to the applicable platform design guidelines
for details. Termination resistors (RTT) for AGTL+ signals are provided on the processor
silicon and are terminated to VTT. The on-die termination resistors are always enabled
on the processor to control reflections on the transmission line. Intel chipsets also
provide on-die termination, thus eliminating the need to terminate the bus on the
baseboard for most AGTL+ signals.
Some FSB signals do not include on-die termination (RTT) and must be terminated on
the baseboard. See Table 2-7 and Table 2-8 for details regarding these signals.
The AGTL+ bus depends on incident wave switching. Therefore, timing calculations for
AGTL+ signals are based on flight time as opposed to capacitive deratings. Analog
signal simulation of the FSB, including trace lengths, is highly recommended when
designing a system. Contact your Intel Field Representative to obtain the applicable
signal integrity models, which includes buffer and package models.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
17
Electrical Specifications
2.2
Power and Ground Lands
For clean on-chip processor core power distribution, the processor has 223 VCC (power)
and 267 VSS (ground) inputs. All VCC lands must be connected to the processor power
plane, while all VSS lands must be connected to the system ground plane. The
processor VCC lands must be supplied with the voltage determined by the processor
Voltage IDentification (VID) signals. See Table 2-3 for VID definitions.
Twenty two lands are specified as VTT, which provide termination for the FSB and
provides power to the I/O buffers. The platform must implement a separate supply for
these lands which meets the VTT specifications outlined in Table 2-12.
2.3
Decoupling Guidelines
Due to its large number of transistors and high internal clock speeds, the processor is
capable of generating large average current swings between low and full power states.
This may cause voltages on power planes to sag below their minimum values if bulk
decoupling is not adequate. Larger bulk storage (CBULK), such as electrolytic capacitors,
supply current during longer lasting changes in current demand by the component,
such as coming out of an idle condition. Similarly, they act as a storage well for current
when entering an idle condition from a running condition. Care must be taken in the
baseboard design to ensure that the voltage provided to the processor remains within
the specifications listed in Table 2-12. Failure to do so can result in timing violations or
reduced lifetime of the component. For further information and guidelines, refer to the
appropriate platform design guidelines.
2.3.1
VCC Decoupling
Vcc regulator solutions need to provide bulk capacitance with a low Effective Series
Resistance (ESR), and the baseboard designer must assure a low interconnect
resistance from the regulator (EVRD or VRM pins) to the LGA771 socket. Bulk
decoupling must be provided on the baseboard to handle large current swings. The
power delivery solution must insure the voltage and current specifications are met (as
defined in Table 2-12). For further information regarding power delivery, decoupling
and layout guidelines, refer to the appropriate platform design guidelines.
2.3.2
VTT Decoupling
Bulk decoupling must be provided on the baseboard. Decoupling solutions must be
sized to meet the expected load. To insure optimal performance, various factors
associated with the power delivery solution must be considered including regulator
type, power plane and trace sizing, and component placement. A conservative
decoupling solution consists of a combination of low ESR bulk capacitors and high
frequency ceramic capacitors. For further information regarding power delivery,
decoupling and layout guidelines, refer to the appropriate platform design guidelines.
18
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
2.3.3
Front Side Bus AGTL+ Decoupling
The processor integrates signal termination on the die, as well as a portion of the
required high frequency decoupling capacitance on the processor package. However,
additional high frequency capacitance must be added to the baseboard to properly
decouple the return currents from the FSB. Bulk decoupling must also be provided by
the baseboard for proper AGTL+ bus operation. Decoupling guidelines are described in
the appropriate platform design guidelines.
2.4
Front Side Bus Clock (BCLK[1:0]) and Processor
Clocking
BCLK[1:0] directly controls the FSB interface speed as well as the core frequency of the
processor. As in previous processor generations, the processor core frequency is a
multiple of the BCLK[1:0] frequency. The processor bus ratio multiplier is set during
manufacturing. The default setting is for the maximum speed of the processor. It is
possible to override this setting using software (see the Conroe and Woodcrest
Processor Family BIOS Writer’s Guide). This permits operation at lower frequencies
than the processor’s tested frequency.
The processor core frequency is configured during reset by using values stored
internally during manufacturing. The stored value sets the highest bus fraction at which
the particular processor can operate. If lower speeds are desired, the appropriate ratio
can be configured via the CLOCK_FLEX_MAX Model Specific Register (MSR). For details
of operation at core frequencies lower than the maximum rated processor speed, refer
to the Intel® 64 and IA-32 Architectures Software Developer’s Manual.
Clock multiplying within the processor is provided by the internal phase locked loop
(PLL), which requires a constant frequency BCLK[1:0] input, with exceptions for spread
spectrum clocking. Processor DC specifications for the BCLK[1:0] inputs are provided in
Table 2-21. These specifications must be met while also meeting signal integrity
requirements as outlined in Table 2-21. The processor utilizes differential clocks.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
19
Electrical Specifications
Table 2-1.
Core Frequency to FSB Multiplier Configuration
Core Frequency
to FSB
Multiplier
Core Frequency with
333.333 MHz Bus
Clock
Core Frequency with
266.666 MHz Bus
Clock
Notes
1/6
2 GHz
1.60 GHz
1, 2, 3, 4
1/7
2.33 GHz
1.86 GHz
1, 2, 3
1/8
2.66 GHz
2.13 GHz
1, 2, 3
1/9
3 GHz
2.40 GHz
1, 2, 3
1/10
3.33 GHz
2.66 GHz
1, 2, 3
1/11
3.66 GHz
2.93 GHz
1, 2, 3
1/12
4 GHz
3.20 GHz
1, 2, 3
Notes:
1.
Individual processors operate only at or below the frequency marked on the package.
2.
Listed frequencies are not necessarily committed production frequencies.
3.
For valid processor core frequencies, refer to the Quad-Core Intel® Xeon® Processor 5300 Series
Specification Update.
4.
The lowest bus ratio supported is 1/6.
2.4.1
Front Side Bus Frequency Select Signals (BSEL[2:0])
Upon power up, the FSB frequency is set to the maximum supported by the individual
processor. BSEL[2:0] are CMOS outputs which must be pulled up to VTT, and are used
to select the FSB frequency. Please refer to Table 2-17 for DC specifications. Table 2-2
defines the possible combinations of the signals and the frequency associated with each
combination. The frequency is determined by the processor(s), chipset, and clock
synthesizer. All FSB agents must operate at the same core and FSB frequency. See the
appropriate platform design guidelines for further details.
Table 2-2.
20
BSEL[2:0] Frequency Table
BSEL2
BSEL1
BSEL0
Bus Clock Frequency
0
0
0
266.666 MHz
0
0
1
Reserved
0
1
0
Reserved
0
1
1
Reserved
1
0
0
333.333 MHz
1
0
1
Reserved
1
1
0
Reserved
1
1
1
Reserved
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
2.4.2
PLL Power Supply
An on-die PLL filter solution is implemented on the processor. The VCCPLL input is used
to provide power to the on chip PLL of the processor. Please refer to Table 2-12 for DC
specifications. Refer to the appropriate platform design guidelines for decoupling and
routing guidelines.
2.5
Voltage Identification (VID)
The Voltage Identification (VID) specification for the processor is defined by the Voltage
Regulator Module (VRM) and Enterprise Voltage Regulator-Down (EVRD) 11.0 Design
Guidelines. The voltage set by the VID signals is the reference VR output voltage to be
delivered to the processor Vcc pins. Please refer to Table 2-18 for the DC specifications
for these signals. A voltage range is provided in Table 2-12 and changes with
frequency. The specifications have been set such that one voltage regulator can
operate with all supported frequencies.
Individual processor VID values may be calibrated during manufacturing such that two
devices at the same core frequency may have different default VID settings. This is
reflected by the VID range values provided in Table 2-3.
The Quad-Core Intel® Xeon® Processor 5300 Series uses six voltage identification
signals, VID[6:1], to support automatic selection of power supply voltages. Table 2-3
specifies the voltage level corresponding to the state of VID[6:1]. A ‘1’ in this table
refers to a high voltage level and a ‘0’ refers to a low voltage level. The definition
provided in Table 2-3 is not related in any way to previous Intel® Xeon® processors or
voltage regulator designs. If the processor socket is empty (VID[6:1] = 111111), or
the voltage regulation circuit cannot supply the voltage that is requested, the voltage
regulator must disable itself. See the Voltage Regulator Module (VRM) and Enterprise
Voltage Regulator-Down (EVRD) 11.0 Design Guidelines for further details.
Although the Voltage Regulator Module (VRM) and Enterprise Voltage Regulator-Down
(EVRD) 11.0 Design Guidelines defines VID[7:0], VID[7] and VID[0] are not used on
the Quad-Core Intel® Xeon® Processor 5300 Series. Please refer to the Quad-Core
Intel® Xeon® Processor E5300 Series, Harpertown and Wolfdale-DP Processors
Compatibility Design Guide for details.
The Quad-Core Intel® Xeon® Processor 5300 Series provide the ability to operate
while transitioning to an adjacent VID and its associated processor core voltage (VCC).
This will represent a DC shift in the load line. It should be noted that a low-to-high or
high-to-low voltage state change may result in as many VID transitions as necessary to
reach the target core voltage. Transitions above the specified VID are not permitted.
Table 2-12 includes VID step sizes and DC shift ranges. Minimum and maximum
voltages must be maintained as shown in Table 2-13.
The VRM or EVRD utilized must be capable of regulating its output to the value defined
by the new VID. DC specifications for dynamic VID transitions are included in
Table 2-12. Refer to the Voltage Regulator Module (VRM) and Enterprise Voltage
Regulator-Down (EVRD) 11.0 Design Guidelines for further details.
Power source characteristics must be guaranteed to be stable whenever the supply to
the voltage regulator is stable.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
21
Electrical Specifications
Table 2-3.
HEX
VID6
400
mV
Voltage Identification Definition
VID5
200
mV
VID4
100
mV
VID3
50
mV
VID2
25
mV
VID1
12.5
mV
VCC_MAX
HEX
VID6
400
mV
VID5
200
mV
VID4
100
mV
VID3
50
mV
VID2
25
mV
VID1
12.5
mV
VCC_MAX
7A
1
1
1
1
0
1
0.8500
3C
0
1
1
1
1
0
1.2375
78
1
1
1
1
0
0
0.8625
3A
0
1
1
1
0
1
1.2500
76
1
1
1
0
1
1
0.8750
38
0
1
1
1
0
0
1.2625
74
1
1
1
0
1
0
0.8875
36
0
1
1
0
1
1
1.2750
72
1
1
1
0
0
1
0.9000
34
0
1
1
0
1
0
1.2875
70
1
1
1
0
0
0
0.9125
32
0
1
1
0
0
1
1.3000
6E
1
1
0
1
1
1
0.9250
30
0
1
1
0
0
0
1.3125
6C
1
1
0
1
1
0
0.9375
2E
0
1
0
1
1
1
1.3250
6A
1
1
0
1
0
1
0.9500
2C
0
1
0
1
1
0
1.3375
68
1
1
0
1
0
0
0.9625
2A
0
1
0
1
0
1
1.3500
66
1
1
0
0
1
1
0.9750
28
0
1
0
1
0
0
1.3625
64
1
1
0
0
1
0
0.9875
26
0
1
0
0
1
1
1.3750
62
1
1
0
0
0
1
1.0000
24
0
1
0
0
1
0
1.3875
60
1
1
0
0
0
0
1.0125
22
0
1
0
0
0
1
1.4000
5E
1
0
1
1
1
1
1.0250
20
0
1
0
0
0
0
1.4125
5C
1
0
1
1
1
0
1.0375
1E
0
0
1
1
1
1
1.4250
5A
1
0
1
1
0
1
1.0500
1C
0
0
1
1
1
0
1.4375
58
1
0
1
1
0
0
1.0625
1A
0
0
1
1
0
1
1.4500
56
1
0
1
0
1
1
1.0750
18
0
0
1
1
0
0
1.4625
54
1
0
1
0
1
0
1.0875
16
0
0
1
0
1
1
1.4750
52
1
0
1
0
0
1
1.1000
14
0
0
1
0
1
0
1.4875
50
1
0
1
0
0
0
1.1125
12
0
0
1
0
0
1
1.5000
4E
1
0
0
1
1
1
1.1250
10
0
0
1
0
0
0
1.5125
4C
1
0
0
1
1
0
1.1375
0E
0
0
0
1
1
1
1.5250
4A
1
0
0
1
0
1
1.1500
0C
0
0
0
1
1
0
1.5375
48
1
0
0
1
0
0
1.1625
0A
0
0
0
1
0
1
1.5500
46
1
0
0
0
1
1
1.1750
08
0
0
0
1
0
0
1.5625
44
1
0
0
0
1
0
1.1875
06
0
0
0
0
1
1
1.5750
42
1
0
0
0
0
1
1.2000
04
0
0
0
0
1
0
1.5875
40
1
0
0
0
0
0
1.2125
02
0
0
0
0
0
1
1.6000
3E
0
1
1
1
1
1
1.2250
00
0
0
0
0
0
0
OFF1
Notes:
1.
When the “111111” VID pattern is observed, the voltage regulator output should be disabled.
2.
Shading denotes the expected VID range of the Quad-Core Intel® Xeon® Processor 5300 Series.
3.
The VID range includes VID transitions that may be initiated by thermal events, assertion of the FORCEPR# signal (see
Section 6.3.3), Extended HALT state transitions (see Section 7.2.2), or Enhanced Intel SpeedStep® Technology transitions
(see Section 7.3). The Extended HALT state must be enabled for the processor to remain within its specifications.
4.
Once the VRM/EVRD is operating after power-up, if either the Output Enable signal is de-asserted or a specific VID off code is
received, the VRM/EVRD must turn off its output (the output should go to high impedance) within 500 ms and latch off until
power is cycled. Refer to Voltage Regulator Module (VRM) and Enterprise Voltage Regulator-Down (EVRD) 11.0 Design
Guidelines.
22
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Table 2-4.
Loadline Selection Truth Table for LL_ID[1:0]
LL_ID1
LL_ID0
0
0
Reserved
0
1
Dual-Core Intel® Xeon® Processor 5000 Series
Dual-Core Intel® Xeon® Processor 5100 Series
1
0
Reserved
1
1
Quad-Core Intel® Xeon® Processor 5300 Series
Note:
Table 2-5.
The LL_ID[1:0] signals are used by the platform to select the correct loadline slope for the processor.
Market Segment Selection Truth Table for MS_ID[1:0]
MS_ID1
MS_ID0
0
0
Dual-Core Intel® Xeon® Processor 5000 Series
0
1
Dual-Core Intel® Xeon® Processor 5100 Series
1
0
All Quad-Core Intel® Xeon® Processor 5300 Series
1
1
Reserved
Note:
2.6
Description
Description
The MS_ID[1:0] signals are provided to indicate the Market Segment for the processor and may be
used for future processor compatibility or for keying.
Reserved, Unused, or Test Signals
All Reserved signals must remain unconnected. Connection of these signals to VCC, VTT,
VSS, or to any other signal (including each other) can result in component malfunction
or incompatibility with future processors. See Section 4 for a land listing of the
processor and the location of all Reserved signals.
For reliable operation, always connect unused inputs or bidirectional signals to an
appropriate signal level. Unused active high inputs, should be connected through a
resistor to ground (VSS). Unused outputs can be left unconnected; however, this may
interfere with some TAP functions, complicate debug probing, and prevent boundary
scan testing. A resistor must be used when tying bidirectional signals to power or
ground. When tying any signal to power or ground, a resistor will also allow for system
testability. Resistor values should be within ± 20% of the impedance of the baseboard
trace for FSB signals, unless otherwise noticed in the appropriate platform design
guidelines. For unused AGTL+ input or I/O signals, use pull-up resistors of the same
value as the on-die termination resistors (RTT). For details see Table 2-20.
Some TAP, CMOS inputs and outputs do not include on-die termination. Inputs and
utilized outputs must be terminated on the baseboard. Unused outputs may be
terminated on the baseboard or left unconnected. Note that leaving unused outputs
unterminated may interfere with some TAP functions, complicate debug probing, and
prevent boundary scan testing. Signal termination for these signal types is discussed in
the appropriate platform design guidelines.
For each processor socket, connect the TESTIN1 and TESTIN2 signals together, then
terminate the net with a 51 Ω resistor to VTT.
Each of the TESTHI signals must be tied to the processor VTT individually using a
matched resistor, where a matched resistor has a resistance value within ± 20% of the
impedance of the board transmission line traces. For example, if the trace impedance is
50 Ω, then a value between 40 Ω and 60 Ω is required.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
23
Electrical Specifications
2.7
Front Side Bus Signal Groups
The FSB signals have been combined into groups by buffer type. AGTL+ input signals
have differential input buffers, which use GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID, and GTLREF_ADD_END as reference levels. In this document, the
term “AGTL+ Input” refers to the AGTL+ input group as well as the AGTL+ I/O group
when receiving. Similarly, “AGTL+ Output” refers to the AGTL+ output group as well as
the AGTL+ I/O group when driving. AGTL+ outputs can become active anytime and
include an active PMOS pull-up transistor to assist during the first clock of a low-to-high
voltage transition.
With the implementation of a source synchronous data bus comes the need to specify
two sets of timing parameters. One set is for common clock signals whose timings are
specified with respect to rising edge of BCLK0 (ADS#, HIT#, HITM#, etc.) and the
second set is for the source synchronous signals which are relative to their respective
strobe lines (data and address) as well as rising edge of BCLK0. Asynchronous signals
are still present (A20M#, IGNNE#, etc.) and can become active at any time during the
clock cycle. Table 2-6 identifies which signals are common clock, source synchronous
and asynchronous.
Table 2-6.
FSB Signal Groups (Sheet 1 of 2)
Signal Group
24
Signals1
Type
AGTL+ Common Clock Input
Synchronous to
BCLK[1:0]
BPRI#, DEFER#, RESET#, RS[2:0]#, RSP#,
TRDY#;
AGTL+ Common Clock Output
Synchronous to
BCLK[1:0]
BPM4#, BPM[2:1]#, BPMb[2:1]#
AGTL+ Common Clock I/O
Synchronous to
BCLK[1:0]
ADS#, AP[1:0]#, BINIT#2, BNR#2, BPM5#,
BPM3#, BPM0#, BPMb3#, BPMb0#, BR[1:0]#,
DBSY#, DP[3:0]#, DRDY#, HIT#2, HITM#2,
LOCK#, MCERR#2
AGTL+ Source Synchronous I/O
Synchronous to assoc.
strobe
Signals
Associated Strobe
REQ[4:0]#,A[16:3]#,
A[37:36]#3
ADSTB0#
A[35:17]#
ADSTB1#
D[15:0]#, DBI0#
DSTBP0#, DSTBN0#
D[31:16]#, DBI1#
DSTBP1#, DSTBN1#
D[47:32]#, DBI2#
DSTBP2#, DSTBN2#
D[63:48]#, DBI3#
DSTBP3#, DSTBN3#
AGTL+ Strobes I/O
Synchronous to
BCLK[1:0]
ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#
Open Drain Output
Asynchronous
FERR#/PBE#, IERR#, PROCHOT#, THERMTRIP#
CMOS Asynchronous Input
Asynchronous
A20M#, FORCEPR#, IGNNE#, INIT#, LINT0/
INTR, LINT1/NMI, PWRGOOD, SMI#, STPCLK#,
CMOS Asynchronous Output
Asynchronous
BSEL[2:0], VID[6:1]
FSB Clock
Clock
BCLK[1:0]
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Table 2-6.
FSB Signal Groups (Sheet 2 of 2)
Signal Group
Signals1
Type
TAP Input
Synchronous to TCK
TCK, TDI, TMS, TRST#
TAP Output
Synchronous to TCK
TDO
Power/Other
Power/Other
COMP[3:0], GTLREF_ADD_MID,
GTLREF_ADD_END, GTLREF_DATA_MID,
GTLREF_DATA_END, LL_ID[1:0], MS_ID[1:0],
PECI, RESERVED, SKTOCC#, TESTHI[11:10],
TESTHI[7:0], TESTIN1, TESTIN2, VCC,
VCC_DIE_SENSE, VCC_DIE_SENSE2, VCCPLL,
VID_SELECT, VSS_DIE_SENSE,
VSS_DIE_SENSE2, VSS, VTT, VTT_OUT,
VTT_SEL
Notes:
1.
Refer to Section 5 for signal descriptions.
2.
These signals may be driven simultaneously by multiple agents (Wired-OR).
3.
Not all Quad-Core Intel® Xeon® Processor 5300 Series support the additional signals A[37:36]#.
Processors that support these signals will be outlined in the Quad-Core Intel® Xeon® Processor 5300
Series NDA Specification Update.
Table 2-7 and Table 2-8 outline the signals which include on-die termination (RTT).
Table 2-7 denotes AGTL+ signals, while Table 2-8 outlines non AGTL+ signals including
open drain signals. Table 2-9 provides signal reference voltages.
Table 2-7.
AGTL+ Signal Description Table
AGTL+ signals with RTT
1
A[37:3]# , ADS#, ADSTB[1:0]#, AP[1:0]#,
BINIT#, BNR#, BPRI#, D[63:0]#, DBI[3:0]#,
DBSY#, DEFER#, DP[3:0]#, DRDY#, DSTBN[3:0]#,
DSTBP[3:0]#, HIT#, HITM#, LOCK#, MCERR#,
REQ[4:0]#, RS[2:0]#, RSP#, TRDY#
AGTL+ signals with no RTT
BPM[5:0]#, BPMb[3:0]#, RESET#, BR[1:0]#
Note:
1.
Not all Quad-Core Intel® Xeon® Processor 5300 Series support the additional signals A[37:36]#.
Processors that support these signals will be outlined in the Quad-Core Intel® Xeon® Processor 5300
Series NDA Specification Update.
Table 2-8.
Non AGTL+ Signal Description Table
Signals with RTT
FORCEPR#1,
PROCHOT#1
Signals with no RTT
A20M#, BCLK[1:0], BSEL[2:0], COMP[3:0], FERR#/
PBE#, GTLREF_ADD_MID, GTLREF_ADD_END,
GTLREF_DATA_MID, GTLREF_DATA_END, IERR#,
IGNNE#, INIT#, LINT0/INTR, LINT1/NMI, LL_ID[1:0],
MS_ID[1:0], PECI, PWRGOOD, SKTOCC#, SMI#,
STPCLK#, TCK, TDI, TDO, TESTHI[11:10], TESTHI[7:0],
TESTIN1, TESTIN2, THERMTRIP#, TMS, TRST#,
VCC_DIE_SENSE, VCC_DIE_SENSE2, VID[6:1],
VID_SELECT, VSS_DIE_SENSE, VSS_DIE_SENSE2,
VTT_SEL
Note:
1.
Signals that have a 50 Ω pullup to VTT on package.
Table 2-9.
Signal Reference Voltages
GTLREF
1
A[37:3]# , ADS#, ADSTB[1:0]#, AP[1:0]#,
BINIT#, BNR#, BPM[5:0]#, BPMb[3:0]#, BPRI#,
BR[1:0]#, D[63:0]#, DBI[3:0]#, DBSY#, DEFER#,
DP[3:0]#, DRDY#, DSTBN[3:0]#, DSTBP[3:0]#,
HIT#, HITM#, LOCK#, MCERR#, RESET#,
REQ[4:0]#, RS[2:0]#, RSP#, TRDY#
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
CMOS
A20M#, FORCEPR#, IGNNE#, INIT#, LINT0/INTR,
LINT1/NMI, PWRGOOD, SMI#, STPCLK#, TCK, TDI,
TMS, TRST#
25
Electrical Specifications
Note:
1.
Not all Quad-Core Intel® Xeon® Processor 5300 Series support the additional signals A[37:36]#.
Processors that support these signals will be outlined in the Quad-Core Intel® Xeon® Processor 5300
Series NDA Specification Update.
2.8
CMOS Asynchronous and Open Drain
Asynchronous Signals
Legacy input signals such as A20M#, IGNNE#, INIT#, SMI#, and STPCLK# utilize
CMOS input buffers. Legacy output signals such as FERR#/PBE#, IERR#, PROCHOT#,
and THERMTRIP# utilize open drain output buffers. All of the CMOS and Open Drain
signals are required to be asserted/deasserted for at least eight BCLKs in order for the
processor to recognize the proper signal state. See Section 2.13 for the DC
specifications. See Section 7 for additional timing requirements for entering and
leaving the low power states.
2.9
Test Access Port (TAP) Connection
Due to the voltage levels supported by other components in the Test Access Port (TAP)
logic, it is recommended that the processor(s) be first in the TAP chain and followed by
any other components within the system. A translation buffer should be used to
connect to the rest of the chain unless one of the other components is capable of
accepting an input of the appropriate voltage. Similar considerations must be made for
TCK, TDO, TMS, and TRST#. Two copies of each signal may be required with each
driving a different voltage level.
2.10
Platform Environmental Control Interface (PECI)
DC Specifications
PECI is an Intel proprietary one-wire interface that provides a communication channel
between Intel processor and external thermal monitoring devices. The Quad-Core
Intel® Xeon® Processor 5300 Series contains Digital Thermal Sensors (DTS)
distributed throughout the die. These sensors are implemented as analog-to-digital
converters calibrated at the factor for reasonable accuracy to provide a digital
representation of relative processor temperature. PECI provides an interface to relay
the highest DTS temperature within a die to external management devices for thermal/
fan speed control. More detailed information may be found in the Platform Environment
Control Interface (PECI) External Architecture Specification.
2.10.1
DC Characteristics
A PECI device interface operates at a nominal voltage set by VTT. The set of DC
electrical specifications shown in Table 2-10 is used with devices normally operating
from a VTT interface supply. VTT nominal levels will vary between processor families. All
PECI devices will operate at the VTT level determined by the processor installed in the
system. For VTT specifications, refer to Table 2-12.
Table 2-10. PECI DC Electrical Limits (Sheet 1 of 2)
Symbol
Vin
Vhysteresis
VN
26
Definition and Conditions
Min
Max
Units
Input Voltage Range
-0.150
VTT
V
Hysteresis
0.1 * VTT
N/A
V
Negative-edge threshold
voltage
0.275 * VTT
0.500 * VTT
V
Notes1
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Table 2-10. PECI DC Electrical Limits (Sheet 2 of 2)
Symbol
Notes1
Definition and Conditions
Min
Max
Units
Vp
Positive-edge threshold
voltage
0.550 * VTT
0.725 * VTT
V
Isource
High level output source
-6.0
N/A
mA
0.5
1.0
mA
N/A
50
µA
2
N/A
10
µA
2
Bus capacitance per node
N/A
10
pF
3
Signal noise immunity
above 300 MHz
0.1 * VTT
N/A
Vp-p
(VOH = 0.75 * VTT)
Low level output sink
Isink
(VOL = 0.25 * VTT)
Ileak+
High impedance state
leakage to VTT
(Vleak = VOL)
Ileak-
High impedance leakage
to GND
(Vleak = VOH)
Cbus
Vnoise
Note:
1.
VTT supplies the PECI interface. PECI behavior does not affect VTT min/max specifications.
2.
The leakage specification applies to powered devices on the PECI bus.
3.
One node is counted for each client and one node for the system host. Extended trace lengths might appear
as additional nodes.
2.10.2
Input Device Hysteresis
The input buffers in both client and host models must use a Schmitt-triggered input
design for improved noise immunity. Use Figure 2-1 as a guide for input buffer design.
Figure 2-1.
Input Device Hysteresis
VTT
Maximum VP
PECI High Range
Minimum VP
Minimum
Hysteresis
Valid Input
Signal Range
Maximum VN
Minimum VN
PECI Low Range
PECI Ground
2.11
Mixing Processors
Intel supports and validates dual processor configurations only in which both
processors operate with the same FSB frequency, core frequency, number of cores, and
have the same internal cache sizes. Mixing components operating at different internal
clock frequencies is not supported and will not be validated by Intel. Combining
processors from different power segments is also not supported.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
27
Electrical Specifications
Note:
Processors within a system must operate at the same frequency per bits [12:8] of the
CLOCK_FLEX_MAX MSR; however this does not apply to frequency transitions initiated
due to thermal events, Extended HALT, Enhanced Intel SpeedStep® Technology
transitions, or assertion of the FORCEPR# signal.
Not all operating systems can support dual processors with mixed frequencies. Mixing
processors of different steppings but the same model (as per CPUID instruction) is
supported. Details regarding the CPUID instruction are provided in the AP-485 Intel®
Processor Identification and the CPUID Instruction application note.
2.12
Absolute Maximum and Minimum Ratings
Table 2-11 specifies absolute maximum and minimum ratings only, which lie outside
the functional limits of the processor. Only within specified operation limits, can
functionality and long-term reliability be expected.
At conditions outside functional operation condition limits, but within absolute
maximum and minimum ratings, neither functionality nor long-term reliability can be
expected. If a device is returned to conditions within functional operation limits after
having been subjected to conditions outside these limits, but within the absolute
maximum and minimum ratings, the device may be functional, but with its lifetime
degraded depending on exposure to conditions exceeding the functional operation
condition limits.
At conditions exceeding absolute maximum and minimum ratings, neither functionality
nor long-term reliability can be expected. Moreover, if a device is subjected to these
conditions for any length of time then, when returned to conditions within the
functional operating condition limits, it will either not function or its reliability will be
severely degraded.
Although the processor contains protective circuitry to resist damage from static
electric discharge, precautions should always be taken to avoid high static voltages or
electric fields.
.
Table 2-11. Processor Absolute Maximum Ratings
Symbol
Parameter
Min
Max
Unit
VCC
Core voltage with respect to VSS
-0.30
1.55
V
VTT
FSB termination voltage with respect to
VSS
-0.30
1.55
V
TCASE
Processor case temperature
See
Section 6
See
Section 6
°C
TSTORAGE
Storage temperature
-40
85
°C
Notes1, 2
3, 4, 5
Notes:
1.
For functional operation, all processor electrical, signal quality, mechanical and thermal specifications must
be satisfied.
2.
Overshoot and undershoot voltage guidelines for input, output, and I/O signals are outlined in Section 3.
Excessive overshoot or undershoot on any signal will likely result in permanent damage to the processor.
3.
Storage temperature is applicable to storage conditions only. In this scenario, the processor must not
receive a clock, and no lands can be connected to a voltage bias. Storage within these limits will not affect
the long-term reliability of the device. For functional operation, please refer to the processor case
temperature specifications.
4.
This rating applies to the processor and does not include any tray or packaging.
5.
Failure to adhere to this specification can affect the long-term reliability of the processor.
28
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
2.13
Processor DC Specifications
The processor DC specifications in this section are defined at the processor die
(pads) unless noted otherwise. See Table 4-1 for the Quad-Core Intel® Xeon®
Processor 5300 Series land listings and Table 5-1 for signal definitions. Voltage and
current specifications are detailed in Table 2-12. For platform planning refer to
Table 2-13, which provides VCC Static and Transient Tolerances. This same information
is presented graphically in Figure 2-7, Figure 2-8 and Figure 2-9.
The FSB clock signal group is detailed in Table 2-21. The DC specifications for the
AGTL+ signals are listed in Table 2-16. Legacy signals and Test Access Port (TAP)
signals follow DC specifications similar to GTL+. The DC specifications for the
PWRGOOD input and TAP signal group are listed in Table 2-17.
Table 2-12 through Table 2-18 list the DC specifications for the processor and are valid
only while meeting specifications for case temperature (TCASE as specified in Section 6),
clock frequency, and input voltages. Care should be taken to read all notes associated
with each parameter.
2.13.1
Flexible Motherboard Guidelines (FMB)
The Flexible Motherboard (FMB) guidelines are estimates of the maximum values the
Quad-Core Intel® Xeon® Processor 5300 Series will have over certain time periods.
The values are only estimates and actual specifications for future processors may differ.
Processors may or may not have specifications equal to the FMB value in the
foreseeable future. System designers should meet the FMB values to ensure their
systems will be compatible with future processors.
Table 2-12. Voltage and Current Specifications (Sheet 1 of 3)
Symbol
Parameter
Min
Typ
Max
Unit
Notes 1,11
VID
VID range for Quad-Core Intel®
Xeon® Processor E5300 , QuadCore Intel® Xeon® Processor
X5300 Series, and Quad-Core
Intel® Xeon® Processor X5365
Series
1.0000
1.5000
V
VID
VID Range for Quad-Core Intel®
Xeon® Processor L5300 Series
1.1000
1.2500
V
VID
VID Range for Quad-Core Intel®
Xeon® Processor L5318
0.9000
1.2500
V
VCC
VCC for processor core
Launch - FMB
See Table 2-13, Figure 2-7,
Figure 2-8 and Table 2-9
V
2, 3, 4, 6, 9
VCC_BOOT
Default VCC Voltage for initial power
up
V
2
VVID_STEP
VID step size during a transition
VVID_SHIFT
Total allowable DC load line shift
from VID steps
VTT
FSB termination voltage (DC + AC
specification)
VCCPLL
PLL supply voltage (DC + AC
specification)
ICC
ICC for Quad-Core Intel® Xeon®
Processor E5300 core with multiple
VID
Launch - FMB
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
1.10
± 12.5
mV
450
mV
10
8,13
1.14
1.20
1.26
V
1.455
1.500
1.605
V
90
A
4,5,6,9
29
Electrical Specifications
Table 2-12. Voltage and Current Specifications (Sheet 2 of 3)
Symbol
ICC_RESET
ICC_RESET for Quad-Core Intel®
Xeon® Processor E5300 core with
multiple VID
Launch - FMB
ICC
ICC for Quad-Core Intel® Xeon®
Processor X5300 Series core with
multiple VID
Launch - FMB
ICC_RESET
ICC_RESET for Quad-Core Intel®
Xeon® Processor X5300 Series core
with multiple VID
Launch - FMB
ICC
ICC for Quad-Core Intel® Xeon®
Processor X5365 Series processor
core with multiple VID
Launch - FMB
ICC_RESET
ICC_RESET for Quad-Core Intel®
Xeon® Processor X5365 Series
processor core with multiple VID
Launch - FMB
ICC
ICC for Quad-Core Intel® Xeon®
Processor L5300 Series processor
core with multiple VID
Launch - FMB
ICC_RESET
ICC_RESET for Quad-Core Intel®
Xeon® Processor L5300 Series
processor core with multiple VID
Launch - FMB
ICC
ICC for Quad-Core Intel® Xeon®
Processor L5318 core with multiple
VID
Launch - FMB
ICC_RESET
ICC_RESET for Quad-Core Intel®
Xeon® Processor L5318 core with
multiple VID
Launch - FMB
ITT
ICC for VTT supply before VCC stable
ICC for VTT supply after VCC stable
ICC_TDC
Thermal Design Current (TDC)
Quad-Core Intel® Xeon® Processor
E5300
Launch - FMB
ICC_TDC
ICC_TDC
ICC_TDC
30
Parameter
Thermal Design Current (TDC)
Quad-Core Intel® Xeon® Processor
X5300 Series
Launch - FMB
Thermal Design Current (TDC)
Quad-Core Intel® Xeon® Processor
X5365 Series
Launch - FMB
Thermal Design Current (TDC)
Quad-Core Intel® Xeon® Processor
L5300 Series
Launch - FMB
Min
Typ
Max
Unit
Notes 1,11
90
A
17
125
A
4,5,6,9
125
A
17
150
A
4,5,6,9
150
A
17
60
A
4,5,6,9
60
A
17
50
A
4,5,6,9
50
A
17
8.0
A
15
7.0
A
70
A
6,14
110
A
6,14
130
A
6,14
50
A
6,14
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Table 2-12. Voltage and Current Specifications (Sheet 3 of 3)
Symbol
ICC_TDC
Parameter
Thermal Design Current (TDC)
Quad-Core Intel® Xeon® Processor
L5318
Launch - FMB
Min
Typ
Max
Unit
Notes 1,11
45
A
6,14
580
mA
16
200
µA
7
260
mA
12
90
A
ICC_VTT_OUT
DC current that may be drawn from
VTT_OUT per land
ICC_GTLREF
ICC for
GTLREF_DATA_MID,
GTLREF_DATA_END,
GTLREF_ADD_MID,
GTLREF_ADD_END
ICC_VCCPLL
ICC for PLL supply
ITCC
ICC for Quad-Core Intel® Xeon®
Processor E5300 during active
thermal control circuit (TCC)
ITCC
ICC for Quad-Core Intel® Xeon®
Processor X5300 Series during
active thermal control circuit (TCC)
125
A
ITCC
ICC for Quad-Core Intel® Xeon®
Processor X5365 Series during
active thermal control circuit (TCC)
150
A
ITCC
ICC for Quad-Core Intel® Xeon®
Processor L5300 Series during
active thermal control circuit (TCC)
60
A
ITCC
ICC for Quad-Core Intel® Xeon®
Processor L5318 during active
thermal control circuit (TCC)
50
A
Notes:
1.
Unless otherwise noted, all specifications in this table are based on final silicon characterization data.
2.
These voltages are targets only. A variable voltage source should exist on systems in the event that a
different voltage is required. See Section 2.5 for more information.
3.
The voltage specification requirements are measured across the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands with an oscilloscope set to 100 MHz
bandwidth, 1.5 pF maximum probe capacitance, and 1 MΩ minimum impedance. The maximum length of
ground wire on the probe should be less than 5 mm. Ensure external noise from the system is not coupled
in the scope probe.
4.
The processor must not be subjected to any static VCC level that exceeds the VCC_MAX associated with any
particular current. Failure to adhere to this specification can shorten processor lifetime.
5.
ICC_MAX specification is based on maximum VCC loadline Refer to Figure 2-12 for details. The processor is
capable of drawing ICC_MAX for up to 10 ms. Refer to Figure 2-5, Figure 2-2, and Figure 2-3 for further
details on the average processor current draw over various time durations.
6.
FMB is the flexible motherboard guideline. These guidelines are for estimation purposes only. See
Section 2.13.1 for further details on FMB guidelines.
7.
This specification represents the total current for GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID, and GTLREF_ADD_END.
8.
VTT must be provided via a separate voltage source and must not be connected to VCC. This specification is
measured at the land.
9.
Minimum VCC and maximum ICC are specified at the maximum processor case temperature (TCASE) shown
in Figure 6-1.
10. This specification refers to the total reduction of the load line due to VID transitions below the specified
VID.
11. Individual processor VID values may be calibrated during manufacturing such that two devices at the same
frequency may have different VID settings.
12. This specification applies to the VCCPLL land.
13. Baseboard bandwidth is limited to 20 MHz.
14. ICC_TDC is the sustained (DC equivalent) current that the processor is capable of drawing indefinitely and
should be used for the voltage regulator temperature assessment. The voltage regulator is responsible for
monitoring its temperature and asserting the necessary signal to inform the processor of a thermal
excursion. Please see the applicable design guidelines for further details. The processor is capable of
drawing ICC_TDC indefinitely. Refer to Figure 2-2, Figure 2-3, and Figure 2-5,for further details on the
average processor current draw over various time durations. This parameter is based on design
characterization and is not tested.
15. This is the maximum total current drawn from the VTT plane by only one processor with RTT enabled. This
specification does not include the current coming from on-board termination (RTT), through the signal line.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
31
Electrical Specifications
Refer to the appropriate platform design guide and the Voltage Regulator Design Guidelines to determine
the total ITT drawn by the system. This parameter is based on design characterization and is not tested.
16. ICC_VTT_OUT is specified at 1.2 V.
17. ICC_RESET is specified while PWRGOOD and RESET# are asserted. Refer to Table 2-26 for the PWRGOOD to
RESET# de-assertion time specification and Table 2-23 for the RESET# Pulse Width specification
.
Figure 2-2.
Quad-Core Intel® Xeon® Processor E5300 Series Load Current versus Time
Sustained Current (A)
10 0
95
90
85
80
75
70
65
60
0 .0 1
0 .1
1
10
10 0
10 0 0
Tim e Duration (s)
Notes:
1.
Processor or voltage regulator thermal protection circuitry should not trip for load currents greater than
ICC_TDC.
2.
Not 100% tested. Specified by design characterization.
Figure 2-3.
Quad-Core Intel® Xeon® Processor X5300 Series and Load Current versus
Time
Sustained Current (A)
13 0
12 5
12 0
115
110
10 5
10 0
0 .0 1
0 .1
1
10
10 0
10 0 0
Tim e Duration (s)
Notes:
1.
Processor or voltage regulator thermal protection circuitry should not trip for load currents greater than
ICC_TDC.
2.
Not 100% tested. Specified by design characterization.
32
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Figure 2-4.
Quad-Core Intel® Xeon® Processor X5365 Series Load Current versus Time
Sustained Current (A)
160
155
150
145
140
135
130
125
120
0.01
0.1
1
10
100
1000
Time Duration (s)
Notes:
1.
Processor or voltage regulator thermal protection circuitry should not trip for load currents greater than
ICC_TDC.
2.
Not 100% tested. Specified by design characterization.
Figure 2-5.
Quad-Core Intel® Xeon® Processor L5300 Series Load Current versus Time
65
Sustained Current (A)
60
55
50
45
40
0.01
0.1
1
10
100
1
T im e Du r atio n (s )
Notes:
1.
Processor or voltage regulator thermal protection circuitry should not trip for load currents greater than
ICC_TDC.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
33
Electrical Specifications
2.
Figure 2-6.
Not 100% tested. Specified by design characterization.
Quad-Core Intel® Xeon® Processor L5318 Load Current versus Time
Notes:
1.
Processor or voltage regulator thermal protection circuitry should not trip for load currents greater than
ICC_TDC.
2.
Not 100% tested. Specified by design characterization.
Table 2-13. VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
E5300 Series, Quad-Core Intel® Xeon® Processor X5300 Series, Quad-Core
Intel® Xeon® Processor L5300 Series (Sheet 1 of 2)
ICC (A)
34
VCC_Max (V)
VCC_Typ (V)
VCC_Min (V)
Notes
0
VID - 0.000
VID - 0.015
VID - 0.030
1, 2, 3
5
VID - 0.006
VID - 0.021
VID - 0.036
1, 2, 3
10
VID - 0.013
VID - 0.028
VID - 0.043
1, 2, 3
15
VID - 0.019
VID - 0.034
VID - 0.049
1, 2, 3
20
VID - 0.025
VID - 0.040
VID - 0.055
1, 2, 3
25
VID - 0.031
VID - 0.046
VID - 0.061
1, 2, 3
30
VID - 0.038
VID - 0.053
VID - 0.068
1, 2, 3
35
VID - 0.044
VID - 0.059
VID - 0.074
1, 2, 3
40
VID - 0.050
VID - 0.065
VID - 0.080
1, 2, 3
45
VID - 0.056
VID - 0.071
VID - 0.086
1, 2, 3
50
VID - 0.063
VID - 0.077
VID - 0.093
1, 2, 3
55
VID - 0.069
VID - 0.084
VID - 0.099
1, 2, 3
60
VID - 0.075
VID - 0.090
VID - 0.105
1, 2, 3
65
VID - 0.081
VID - 0.096
VID - 0.111
1, 2, 3, 4
70
VID - 0.087
VID - 0.103
VID - 0.118
1, 2, 3, 4
75
VID - 0.094
VID - 0.109
VID - 0.124
1, 2, 3, 4
80
VID - 0.100
VID - 0.115
VID - 0.130
1, 2, 3, 4
85
VID - 0.106
VID - 0.121
VID - 0.136
1, 2, 3, 4
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Table 2-13. VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
E5300 Series, Quad-Core Intel® Xeon® Processor X5300 Series, Quad-Core
Intel® Xeon® Processor L5300 Series (Sheet 2 of 2)
ICC (A)
VCC_Max (V)
VCC_Typ (V)
VCC_Min (V)
Notes
90
VID - 0.113
VID - 0.128
VID - 0.143
1, 2, 3, 4
95
VID - 0.119
VID - 0.134
VID - 0.149
1, 2, 3, 4
100
VID - 0.125
VID - 0.140
VID - 0.155
1, 2, 3, 4
105
VID - 0.131
VID - 0.146
VID - 0.161
1, 2, 3, 4
110
VID - 0.138
VID - 0.153
VID - 0.168
1, 2, 3, 4
115
VID - 0.144
VID - 0.159
VID - 0.174
1, 2, 3, 4
120
VID - 0.150
VID - 0.165
VID - 0.180
1, 2, 3, 4
125
VID - 0.156
VID - 0.171
VID - 0.186
1, 2, 3, 4
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for
VCC overshoot specifications.
2.
This table is intended to aid in reading discrete points on Figure 2-7 for Quad-Core Intel® Xeon®
Processor E5300 , Figure 2-8 for Quad-Core Intel® Xeon® Processor X5300 Series and Figure 2-9 for
Quad-Core Intel® Xeon® Processor L5300 Series.
3.
The loadlines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for
voltage regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE
lands and VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM)
and Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and
VR implementation. Please refer to the appropriate platform design guide for details on VR
implementation.
4.
Icc values greater than 90 A and 60 A are not applicable for the Quad-Core Intel® Xeon® Processor
E5300 and Quad-Core Intel® Xeon® Processor L5300 Series, respectively.
Figure 2-7.
Quad-Core Intel® Xeon® Processor E5300 Series VCC Static and
Transient Tolerance Load Lines
Icc [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
VID - 0.000
VID - 0.020
VCC
Maximum
VID - 0.040
Vcc [V]
VID - 0.060
VID - 0.080
VID - 0.100
VID - 0.120
VCC
Typical
VID - 0.140
VCC
Minimum
VID - 0.160
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
2.
Refer to Table 2-12 for processor VID information.
3.
Refer to Table 2-13 for VCCStatic and Transient Tolerance
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
35
Electrical Specifications
4.
Figure 2-8.
The load lines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation.
Quad-Core Intel® Xeon® Processor X5300 Series VCC Static and Transient
Tolerance Load Lines
Ic c [A ]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100 105 110 115 120 125
V ID - 0 .0 0 0
V ID - 0 .0 2 0
V ID - 0 .0 4 0
V CC
M a x im u m
V ID - 0 .0 6 0
Vcc [V]
V ID - 0 .0 8 0
V ID - 0 .1 0 0
V ID - 0 .1 2 0
V ID - 0 .1 4 0
V CC
T y p ic a l
V ID - 0 .1 6 0
V ID - 0 .1 8 0
V CC
M in im u m
V ID - 0 .2 0 0
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
2.
Refer to Table 2-12 for processor VID information.
3.
Refer to Table 2-13 for VCCStatic and Transient Tolerance
4.
The load lines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation.
36
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Figure 2-9.
Quad-Core Intel® Xeon® Processor L5300 Series VCC Static and
Transient Tolerance Load Lines
Icc [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
VID - 0.000
VID - 0.010
VCC
Maximum
VID - 0.020
VID - 0.030
Vcc [V]
VID - 0.040
VID - 0.050
VID - 0.060
VID - 0.070
VCC
Typical
VID - 0.080
VID - 0.090
VCC
Minimum
VID - 0.100
Notes:
1.
2.
3.
4.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
Refer to Table 2-12 for processor VID information.
Refer to Table 2-13 for VCCStatic and Transient Tolerance.
The load lines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation
Table 2-14. VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
X5365 Series (Sheet 1 of 2)
ICC (A)
VCC_Max (V)
VCC_Typ (V)
VCC_Min (V)
Notes
0
VID - 0.000
VID - 0.010
VID - 0.020
5
VID - 0.006
VID - 0.016
VID - 0.026
1,2,3
10
VID - 0.013
VID - 0.023
VID - 0.033
1,2,3
15
VID - 0.019
VID - 0.029
VID - 0.039
1,2,3
20
VID - 0.025
VID - 0.035
VID - 0.045
1,2,3
25
VID - 0.031
VID - 0.041
VID - 0.051
1,2,3
30
VID - 0.038
VID - 0.048
VID - 0.058
1,2,3
35
VID - 0.044
VID - 0.054
VID - 0.064
1,2,3
40
VID - 0.050
VID - 0.060
VID - 0.070
1,2,3
45
VID - 0.056
VID - 0.066
VID - 0.076
1,2,3
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
1,2,3
37
Electrical Specifications
Table 2-14. VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
X5365 Series (Sheet 2 of 2)
ICC (A)
VCC_Max (V)
VCC_Typ (V)
VCC_Min (V)
Notes
50
VID - 0.063
VID - 0.073
VID - 0.083
1,2,3
55
VID - 0.069
VID - 0.079
VID - 0.089
1,2,3
60
VID - 0.075
VID - 0.085
VID - 0.095
1,2,3
65
VID - 0.081
VID - 0.091
VID - 0.101
1,2,3
70
VID - 0.087
VID - 0.097
VID - 0.108
1,2,3
75
VID - 0.094
VID - 0.104
VID - 0.114
1,2,3
80
VID - 0.100
VID - 0.110
VID - 0.120
1,2,3
85
VID - 0.106
VID - 0.116
VID - 0.126
1,2,3
90
VID - 0.113
VID - 0.123
VID - 0.133
1,2,3
95
VID - 0.119
VID - 0.129
VID - 0.139
1,2,3
100
VID - 0.125
VID - 0.135
VID - 0.145
1,2,3
105
VID - 0.131
VID - 0.141
VID - 0.151
1,2,3
110
VID - 0.138
VID - 0.148
VID - 0.158
1,2,3
115
VID - 0.144
VID - 0.154
VID - 0.164
1,2,3
120
VID - 0.150
VID - 0.160
VID - 0.170
1,2,3
125
VID - 0.156
VID - 0.166
VID - 0.176
1,2,3
130
VID - 0.163
VID - 0.173
VID - 0.183
1,2,3
135
VID - 0.169
VID - 0.179
VID - 0.189
1,2,3
140
VID - 0.175
VID - 0.185
VID - 0.195
1,2,3
145
VID - 0.181
VID - 0.191
VID - 0.201
1,2,3
150
VID - 0.188
VID - 0.198
VID - 0.208
1,2,3
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
2.
This table is intended to aid in reading discrete points on Figure 2-10 for Quad-Core Intel® Xeon®
Processor X5365 Series
3.
The loadlines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE lands
and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation.
38
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Figure 2-10. Quad-Core Intel® Xeon® Processor X5365 Series VCC Static and Transient
Tolerance Load Lines
Icc [A]
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95 100 105 110 115 120 125 130 135 140 145 150
VID - 0.000
VCC
Maximum
VID - 0.050
Vcc [V]
VID - 0.100
VID - 0.150
VCC
Typical
VID - 0.200
VCC
Minimum
VID - 0.250
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
2.
Refer to Table 2-12 for processor VID information.
3.
Refer to Table 2-14 for VCCStatic and Transient Tolerance.
4.
The load lines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
39
Electrical Specifications
Table 2-15. VCC Static and Transient Tolerance for Quad-Core Intel® Xeon® Processor
L5318 Series
ICC (A)
VCC_Max (V)
VCC_Typ (V)
VCC_Min (V)
Notes
0
VID - 0.000
VID - 0.015
VID - 0.030
1,2,3
5
VID - 0.005
VID - 0.020
VID - 0.035
1,2,3
10
VID - 0.010
VID - 0.025
VID - 0.040
1,2,3
15
VID - 0.015
VID - 0.030
VID - 0.045
1,2,3
20
VID - 0.020
VID - 0.035
VID - 0.050
1,2,3
25
VID - 0.025
VID - 0.040
VID - 0.055
1,2,3
30
VID - 0.030
VID - 0.045
VID - 0.060
1,2,3
35
VID - 0.035
VID - 0.050
VID - 0.065
1,2,3
40
VID - 0.040
VID - 0.055
VID - 0.070
1,2,3
45
VID - 0.045
VID - 0.060
VID - 0.075
1,2,3
50
VID - 0.050
VID - 0.065
VID - 0.080
1,2,3
55
VID - 0.055
VID - 0.070
VID - 0.085
1,2,3
60
VID - 0.060
VID - 0.075
VID - 0.090
1,2,3
Notes:
1.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
2.
This table is intended to aid in reading discrete points on Figure 2-11 for Quad-Core Intel® Xeon®
Processor L5318
3.
The loadlines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE lands
and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation.
40
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Figure 2-11. Quad-Core Intel® Xeon® Processor L5318 VCC Static and Transient Tolerance
Load Lines
Notes:
1.
2.
3.
4.
The VCC_MIN and VCC_MAX loadlines represent static and transient limits. Please see Section 2.13.2 for VCC
overshoot specifications.
Refer to Table 2-12 for processor VID information.
Refer to Table 2-15 for VCCStatic and Transient Tolerance.
The load lines specify voltage limits at the die measured at the VCC_DIE_SENSE and VSS_DIE_SENSE
lands and the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Voltage regulation feedback for voltage
regulator circuits must also be taken from processor VCC_DIE_SENSE and VSS_DIE_SENSE lands and
VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Refer to the Voltage Regulator Module (VRM) and
Enterprise Voltage Regulator Down (EVRD) 11.0 Design Guidelines for socket load line guidelines and VR
implementation. Please refer to the appropriate platform design guide for details on VR implementation.
Table 2-16. AGTL+ Signal Group Specifications
Symbol
Parameter
Min
Typ
Max
Units
Notes1
VIL
Input Low Voltage
-0.10
0
GTLREF-0.10
V
2,4,6
VIH
Input High Voltage
GTLREF+0.10
VTT
VTT+0.10
V
3,6
VOH
Output High Voltage
VTT - 0.10
N/A
VTT
V
4,6
RON
Buffer On Resistance
10.00
11.50
13.00
Ω
5
ILI
Input Leakage Current
N/A
N/A
± 200
μA
7,8
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
VIL is defined as the maximum voltage level at a receiving agent that will be interpreted as a logical low
value.
3.
VIH is defined as the minimum voltage level at a receiving agent that will be interpreted as a logical high
value.
4.
VIH and VOH may experience excursions above VTT. However, input signal drivers must comply with the
signal quality specifications.
5.
This is the pull down driver resistance. Refer to processor I/O Buffer Models for I/V characteristics.
Measured at 0.31*VTT. RON (min) = 0.225*RTT. RON (typ) = 0.250*RTT. RON (max) = 0.275*RTT.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
41
Electrical Specifications
6.
7.
8.
GTLREF should be generated from VTT with a 1% tolerance resistor divider. The VTT referred to in these
specifications is the instantaneous VTT.
Specified when on-die RTT and RON are turned off. VIN between 0 and VTT.
This is the measurement at the pin.
Table 2-17. CMOS Signal Input/Output Group and TAP Signal Group DC Specifications
Symbol
Parameter
Min
Typ
Max
Units
Notes1
VIL
Input Low Voltage
-0.10
0.00
0.3*VTT
V
2,3
VIH
Input High Voltage
0.7*VTT
VTT
VTT+0.1
V
2
VOL
Output Low Voltage
-0.10
0
0.1*VTT
V
2
VOH
Output High Voltage
0.9*VTT
VTT
VTT+0.1
V
2
IOL
Output Low Current
1.70
N/A
4.70
mA
4
IOH
Output High Current
1.70
N/A
4.70
mA
5
ILI
Input Leakage Current
N/A
N/A
± 200
μA
6,7
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
The VTT referred to in these specifications refers to instantaneous VTT.
3.
Refer to the processor I/O Buffer Models for I/V characteristics.
4.
Measured at 0.1*VTT.
5.
Measured at 0.9*VTT.
6.
For Vin between 0 V and VTT. Measured when the driver is tristated.
7.
This is the measurement at the pin.
Table 2-18. Open Drain Output Signal Group DC Specifications
Symbol
Parameter
Min
VOL
Output Low Voltage
VOH
Output High Voltage
IOL
Output Low Current
16
ILO
Leakage Current
N/A
Typ
0.95 * VTT
Max
Units
Notes1
N/A
0.20
V
VTT
1.05 * VTT
V
N/A
50
mA
2
N/A
± 400
μA
4,5
3
Notes:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Measured at 0.2*VTT.
3.
VOH is determined by value of the external pullup resistor to VTT. Please refer to platform design guide for
details.
4.
For VIN between 0 V and VOH.
5.
This is the measurement at the pin.
2.13.2
VCC Overshoot Specification
Processors can tolerate short transient overshoot events where VCC exceeds the VID
voltage when transitioning from a high-to-low current load condition. This overshoot
cannot exceed VID + VOS_MAX (VOS_MAX is the maximum allowable overshoot above
VID). These specifications apply to the processor die voltage as measured across the
VCC_DIE_SENSE and VSS_DIE_SENSE lands and across the VCC_DIE_SENSE2 and
VSS_DIE_SENSE2 lands.
Table 2-19. VCC Overshoot Specifications
Symbol
42
Parameter
Min
Max
Units
Figure
VOS_MAX
Magnitude of VCC overshoot above VID
50
mV
2-12
TOS_MAX
Time duration of VCC overshoot above VID
25
µs
2-12
Notes
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
Figure 2-12. VCC Overshoot Example Waveform
Example Overshoot Waveform
VOS
Voltage [V]
VID + 0.050
VID - 0.000
TOS
0
5
10
15
20
25
Time [us]
TOS: Overshoot time above VID
VOS: Overshoot above VID
Notes:
1.
VOS is the measured overshoot voltage.
2.
TOS is the measured time duration above VID.
2.13.3
Die Voltage Validation
Core voltage (VCC) overshoot events at the processor must meet the specifications in
Table 2-19 when measured across the VCC_DIE_SENSE and VSS_DIE_SENSE lands
and across the VCC_DIE_SENSE2 and VSS_DIE_SENSE2 lands. Overshoot events that
are < 10 ns in duration may be ignored. These measurements of processor die level
overshoot should be taken with a 100 MHz bandwidth limited oscilloscope.
2.14
AGTL+ FSB Specifications
Routing topologies are dependent on the processors supported and the chipset used in
the design. Please refer to the appropriate platform design guidelines for specific
implementation details. In most cases, termination resistors are not required as these
are integrated into the processor silicon. See Table 2-7 for details on which signals do
not include on-die termination. Please refer to Table 2-20 for RTT values.
Valid high and low levels are determined by the input buffers via comparing with a
reference voltage called GTLREF_DATA_MID, GTLREF_DATA_END, GTLREF_ADD_MID,
and GTLREF_ADD_END. GTLREF_DATA_MID and GTLREF_DATA_END are the reference
voltage for the FSB 4X data signals, GTLREF_ADD_MID and GTLREF_ADD_END are the
reference voltage for the FSB 2X address signals and common clock signals. Table 2-20
lists the GTLREF_DATA_MID, GTLREF_DATA_END, GTLREF_ADD_MID, and
GTLREF_ADD_END specifications.
The AGTL+ reference voltages (GTLREF_DATA_MID, GTLREF_DATA_END,
GTLREF_ADD_MID, and GTLREF_ADD_END) must be generated on the baseboard
using high precision voltage divider circuits. Refer to the appropriate platform design
guidelines for implementation details.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
43
Electrical Specifications
Table 2-20. AGTL+ Bus Voltage Definitions
Symbol
Parameter
Min
Typ
Max
Unit
Notes1
GTLREF_DATA_MID
GTLREF_DATA_END
Data Bus
Reference
Voltage
0.98 * 0.67 * VTT
0.67 * VTT
1.02 * 0.67 * VTT
V
2, 3
GTLREF_ADD_MID
GTLREF_ADD_END
Address Bus
Reference
Voltage
0.98 * 0.67 * VTT
0.67 * VTT
1.02 * 0.67 * VTT
V
2, 3
RTT
Termination
Resistance
(pull up)
45
50
55
Ω
4
COMP
Resistance
49.4
49.9
50.4
Ω
5
COMP
Note:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
The tolerances for this specification have been stated generically to enable system designer to calculate the
minimum values across the range of VTT.
3.
GTLREF_DATA_MID, GTLREF_DATA_END, GTLREF_ADD_MID, and GTLREF_ADD_END is generated from VTT
on the baseboard by a voltage divider of 1% resistors. The minimum and maximum specifications account
for this resistor tolerance. Refer to the appropriate platform design guidelines for implementation details.
The VTT referred to in these specifications is the instantaneous VTT.
4.
RTT is the on-die termination resistance measured at VOL of the AGTL+ output driver. Measured at
0.31*VTT. RTT is connected to VTT on die. Refer to processor I/O Buffer Models for I/V characteristics.
5.
COMP resistance must be provided on the system board with +/- 1% resistors. See the applicable platform
design guide for implementation details.
Table 2-21. FSB Differential BCLK Specifications
Symbol
Notes
Parameter
Min
Typ
Max
Unit
Figure
VL
Input Low
Voltage
-0.150
0.0
N/A
V
2-15
VH
Input High
Voltage
0.660
0.710
0.850
V
2-15
VCROSS(abs)
Absolute
Crossing
Point
0.250
0.350
0.550
V
2-15,
2-16
3,9
VCROSS(rel)
Relative
Crossing
Point
0.250 +
0.5 * (VHavg - 0.700)
N/A
0.550 +
0.5 * (VHavg - 0.700)
V
2-15,
2-16
4,9,10
Δ VCROSS
Range of
Crossing
Points
N/A
N/A
0.140
V
2-15,
2-16
12
1,2
VOS
Overshoot
N/A
N/A
VH + 0.300
V
2-15
5
VUS
Undershoot
-0.300
N/A
N/A
V
2-15
6
VRBM
Ringback
Margin
0.200
N/A
N/A
V
2-15
7
VTR
Threshold
Region
VCROSS - 0.100
N/A
VCROSS + 0.100
V
2-15
8
ILI
Input
Leakage
Current
N/A
N/A
+/- 100
μA
11
Note:
1.
Unless otherwise noted, all specifications in this table apply to all processor frequencies.
2.
Rise and fall times are measured single-ended between 245 mV and 455 mV of the clock swing.
3.
Crossing Voltage is defined as the instantaneous voltage value when the rising edge of BCLK0 is equal to
the falling edge of BCLK1.
4.
VHavg is the statistical average of the VH measured by the oscilloscope.
5.
Overshoot is defined as the absolute value of the maximum voltage.
6.
Undershoot is defined as the absolute value of the minimum voltage.
44
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Electrical Specifications
7.
Ringback Margin is defined as the absolute voltage difference between the maximum Rising Edge Ringback
and the maximum Falling Edge Ringback.
8.
Threshold Region is defined as a region entered around the crossing point voltage in which the differential
receiver switches. It includes input threshold hysteresis.
9.
The crossing point must meet the absolute and relative crossing point specifications simultaneously.
10. VHavg can be measured directly using “Vtop” on Agilent and “High” on Tektronix oscilloscopes.
11. For VIN between 0 V and VH.
12. ΔVCROSS is defined as the total variation of all crossing voltages as defined in Note 3.
Figure 2-13. Electrical Test Circuit
Figure 2-14. TCK Clock Waveform
V2
TCK
V3
V1
Tp
Tp = T55: Period
V1, V2: For rise and fall times, TCK is measured between 20% and 80% points on the waveform.
V3: TCK is referenced to 0.5 * VTT
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
45
Electrical Specifications
Figure 2-15. Differential Clock Waveform
Overshoot
BCLK1
VH
Rising Edge
Ringback
Crossing
Voltage
Threshold
Region
Crossing
Voltage
Ringback
Margin
Falling Edge
Ringback,
BCLK0
VL
Undershoot
Tp
Tp = T1: BCLK[1:0] period
Figure 2-16. Differential Clock Crosspoint Specification
650
Crossing Point (mV)
600
550
550 mV
500
450
550 + 0.5 (VHavg - 700)
400
250 + 0.5 (VHavg - 700)
350
300
250
250 mV
200
660 670 680 690 700 710 720 730 740 750 760 770 780 790 800 810 820 830 840 850
VHavg (mV)
§
46
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Mechanical Specifications
3
Mechanical Specifications
The Quad-Core Intel® Xeon® Processor 5300 Series are packaged in a Flip Chip Land
Grid Array (FC-LGA6) package that interfaces to the baseboard via a LGA771 socket.
The package consists of two processor dies mounted on a pinless substrate with 771
lands. An integrated heat spreader (IHS) is attached to the package substrate and core
and serves as the interface for processor component thermal solutions such as a
heatsink. Figure 3-1 shows a sketch of the processor package components and how
they are assembled together. Refer to the LGA771 Socket Design Guidelines for
complete details on the LGA771 socket.
The package components shown in Figure 3-1 include the following:
• Integrated Heat Spreader (IHS)
• Thermal Interface Material (TIM)
• Processor Die
• Package Substrate
• Landside capacitors
• Package Lands
Figure 3-1.
Processor Package Assembly Sketch
IHS
Core (die)
TIM
Substrate
Package Lands
Capacitors
LGA771 Socket
System Board
Note:
3.1
This drawing is not to scale and is for reference only.
Package Mechanical Drawings
The package mechanical drawings are shown in Figure 3-2 through Figure 3-4. The
drawings include dimensions necessary to design a thermal solution for the processor
including:
• Package reference and tolerance dimensions (total height, length, width, and so
forth)
• IHS parallelism and tilt
• Land dimensions
• Top-side and back-side component keepout dimensions
• Reference datums
Note:
All drawing dimensions are in mm [in.].
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
47
Mechanical Specifications
Figure 3-2.
Note:
48
Processor Package Drawing (Sheet 1 of 3)
Guidelines on potential IHS flatness variation with socket load plate actuation and installation of the cooling solution is
available in the processor Thermal/Mechanical Design Guidelines.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Mechanical Specifications
Figure 3-3.
Processor Package Drawing (Sheet 2 of 3)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
49
Mechanical Specifications
Figure 3-4.
50
Processor Package Drawing (Sheet 3 of 3)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Mechanical Specifications
3.2
Processor Component Keepout Zones
The processor may contain components on the substrate that define component
keepout zone requirements. A thermal and mechanical solution design must not intrude
into the required keepout zones. Decoupling capacitors are typically mounted to either
the topside or landside of the package substrate. See Figure 3-4 for keepout zones.
3.3
Package Loading Specifications
Table 3-1 provides dynamic and static load specifications for the processor package.
These mechanical load limits should not be exceeded during heatsink assembly,
mechanical stress testing or standard drop and shipping conditions. The heatsink
attach solutions must not include continuous stress onto the processor with the
exception of a uniform load to maintain the heatsink-to-processor thermal interface.
Also, any mechanical system or component testing should not exceed these limits. The
processor package substrate should not be used as a mechanical reference or loadbearing surface for thermal or mechanical solutions.
Table 3-1.
Package Loading Specifications
Parameter
Static Compressive Load
Dynamic Compressive
Load
Board
Thickness
Min
Max
Unit
Notes
1.57 mm
0.062”
80
18
311
70
N
lbf
1,2,3,9
2.16 mm
0.085”
111
25
311
70
N
lbf
2.54 mm
0.100”
133
30
311
70
N
lbf
NA
NA
311 N (max
static
compressive
load) + 222 N
dynamic loading
N
70 lbf (max
static
compressive
load) + 50 lbf
dynamic loading
Transient Bend Limits
1.57 mm
0.062”
NA
750
1,3,4,5,6
lbf
me
1,3,7,8
Notes:
1.
These specifications apply to uniform compressive loading in a direction perpendicular to the IHS top
surface.
2.
This is the minimum and maximum static force that can be applied by the heatsink and retention solution
to maintain the heatsink and processor interface.
3.
These specifications are based on limited testing for design characterization. Loading limits are for the
LGA771 socket.
4.
Dynamic compressive load applies to all board thickness.
5.
Dynamic loading is defined as an 11 ms duration average load superimposed on the static load
requirement.
6.
Test condition used a heatsink mass of 1 lbm with 50 g acceleration measured at heatsink mass. The
dynamic portion of this specification in the product application can have flexibility in specific values, but the
ultimate product of mass times acceleration should not exceed this dynamic load.
7.
Transient bend is defined as the transient board deflection during manufacturing such as board assembly
and system integration. It is a relatively slow bending event compared to shock and vibration tests.
8.
For more information on the transient bend limits, please refer to the MAS document entitled
Manufacturing with Intel® Components using 771-land LGA Package that Interfaces with the Motherboard
via a LGA771 Socket.
9.
Refer to the Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for
information on heatsink clip load metrology.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
51
Mechanical Specifications
3.4
Package Handling Guidelines
Table 3-2 includes a list of guidelines on a package handling in terms of recommended
maximum loading on the processor IHS relative to a fixed substrate. These package
handling loads may be experienced during heatsink removal.
Table 3-2.
Package Handling Guidelines
Parameter
Maximum Recommended
Units
Notes
Shear
311
70
N
lbf
1,4,5
Tensile
111
25
N
lbf
2,4,5
Torque
3.95
35
N-m
LBF-in
3,4,5
Notes:
1.
A shear load is defined as a load applied to the IHS in a direction parallel to the IHS top surface.
2.
A tensile load is defined as a pulling load applied to the IHS in a direction normal to the IHS surface.
3.
A torque load is defined as a twisting load applied to the IHS in an axis of rotation normal to the IHS top
surface.
4.
These guidelines are based on limited testing for design characterization and incidental applications (one
time only).
5.
Handling guidelines are for the package only and do not include the limits of the processor socket.
3.5
Package Insertion Specifications
The Quad-Core Intel® Xeon® Processor 5300 Series can be inserted and removed 15
times from an LGA771 socket, which meets the criteria outlined in the LGA771 Socket
Design Guidelines.
3.6
Processor Mass Specifications
The typical mass of the Quad-Core Intel® Xeon® Processor 5300 Series is 21.5 g
(0.76 oz). This includes all components which make up the entire processor product.
3.7
Processor Materials
The Quad-Core Intel® Xeon® Processor 5300 Series are assembled from several
components. The basic material properties are described in Table 3-3.
Table 3-3.
Processor Materials
Component
52
Material
Integrated Heat Spreader (IHS)
Nickel over copper
Substrate
Fiber-reinforced resin
Substrate Lands
Gold over nickel
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Mechanical Specifications
3.8
Processor Markings
Figure 3-5 shows the topside markings on the processor. This diagram aids in the
identification of the Quad-Core Intel® Xeon® Processor 5300 Series.
Figure 3-5.
Processor Top-side Markings (Example)
GROUP1LINE1
GROUP1LINE2
GROUP1LINE3
GROUP1LINE4
GROUP1LINE5
LOT
ATPO
NO
S/N
S/N
Legend:
Mark Text (Production Mark):
GROUP1LINE1
GROUP1LINE2
GROUP1LINE3
GROUP1LINE4
GROUP1LINE5
2.66GHZ/8M/1333
Intel ® Xeon®
SXXX XXXXX
i (M) © ’05 x53XX
(FPO)
Legend:
Mark Text (Engineering Mark):
GROUP1LINE1
GROUP1LINE2
GROUP1LINE3
GROUP1LINE4
GROUP1LINE5
INTEL CONFIDENTIAL
QXXX ES XXXXX
i (M) © ‘05 HH80563KJ0678M
(FPO) e4
Notes:
1.
2D matrix is required for engineering samples only (encoded with ATPO-S/N)
3.9
Processor Land Coordinates
Figure 3-6 and Figure 3-7 show the top and bottom view of the processor land
coordinates, respectively. The coordinates are referred to throughout the document to
identify processor lands.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
53
Mechanical Specifications
Figure 3-6.
Processor Land Coordinates, Top View
VCC / VSS
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
6 5
4 3
2 1
AN
AM
AL
AN
AM
AL
AK
AJ
AH
AK
AJ
AH
AG
AF
AE
AG
AF
AE
AD
AC
AD
AC
AB
AA
Y
AB
AA
Y
Socket 771
Quadrants
Top View
W
V
U
T
R
P
W
V
U
T
R
P
N
M
L
N
M
L
K
J
H
K
J
H
G
F
G
F
E
D
C
E
D
C
B
A
B
A
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
VTT / Clocks
54
8 7
8 7
6 5
4 3
Address /
Common Clock /
Async
2 1
Data
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Mechanical Specifications
Figure 3-7.
Processor Land Coordinates, Bottom View
VCC / VSS
1
Address /
Common Clock /
Async
2 3
4
5 6
7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
AN
AM
AL
AK
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
AN
AM
AL
AK
AJ
AH
AG
AF
AE
AD
AC
AB
AA
Y
W
V
U
T
R
P
N
M
L
K
J
H
G
F
E
D
C
B
A
Socket 771
Quadrants
Bottom View
1
2 3
4
5 6
7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
Data
VTT / Clocks
§
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
55
Mechanical Specifications
56
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
4
Land Listing
4.1
Quad-Core Intel® Xeon® Processor 5300 Series
Pin Assignments
This section provides sorted land list in Table 4-1 and Table 4-2. Table 4-1 is a listing of
all processor lands ordered alphabetically by land name. Table 4-2 is a listing of all
processor lands ordered by land number.
4.1.1
Land Listing by Land Name
Table 4-1. Land Listing by Land Name
(Sheet 1 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
Table 4-1. Land Listing by Land Name
(Sheet 2 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
A03#
M5
Source Sync
Input/
Output
A20M#
K3
CMOS
Asynchronous
Input
A04#
P6
Source Sync
Input/
Output
A21#
AA4
Source Sync
Input/
Output
A05#
L5
Source Sync
Input/
Output
A22#
AD6
Source Sync
Input/
Output
A06#
L4
Source Sync
Input/
Output
A23#
AA5
Source Sync
Input/
Output
A07#
M4
Source Sync
Input/
Output
A24#
AB5
Source Sync
Input/
Output
A08#
R4
Source Sync
Input/
Output
A25#
AC5
Source Sync
Input/
Output
A09#
T5
Source Sync
Input/
Output
A26#
AB4
Source Sync
Input/
Output
A10#
U6
Source Sync
Input/
Output
A27#
AF5
Source Sync
Input/
Output
A11#
T4
Source Sync
Input/
Output
A28#
AF4
Source Sync
Input/
Output
A12#
U5
Source Sync
Input/
Output
A29#
AG6
Source Sync
Input/
Output
A13#
U4
Source Sync
Input/
Output
A30#
AG4
Source Sync
Input/
Output
A14#
V5
Source Sync
Input/
Output
A31#
AG5
Source Sync
Input/
Output
A15#
V4
Source Sync
Input/
Output
A32#
AH4
Source Sync
Input/
Output
A16#
W5
Source Sync
Input/
Output
A33#
AH5
Source Sync
Input/
Output
A17#
AB6
Source Sync
Input/
Output
A34#
AJ5
Source Sync
Input/
Output
A18#
W6
Source Sync
Input/
Output
A35#
AJ6
Source Sync
Input/
Output
A19#
Y6
Source Sync
Input/
Output
A36#
N4
Source Sync
Input/
Output
A20#
Y4
Source Sync
Input/
Output
A37#
P5
Source Sync
Input/
Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
57
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 3 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
Table 4-1. Land Listing by Land Name
(Sheet 4 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
ADS#
D2
Common Clk
Input/
Output
D01#
C5
Source Sync
Input/
Output
ADSTB0#
R6
Source Sync
Input/
Output
D02#
A4
Source Sync
Input/
Output
ADSTB1#
AD5
Source Sync
Input/
Output
D03#
C6
Source Sync
Input/
Output
AP0#
U2
Common Clk
Input/
Output
D04#
A5
Source Sync
Input/
Output
AP1#
U3
Common Clk
Input/
Output
D05#
B6
Source Sync
Input/
Output
BCLK0
F28
Clk
Input
D06#
B7
Source Sync
BCLK1
G28
Clk
Input
Input/
Output
BINIT#
AD3
Common Clk
Input/
Output
D07#
A7
Source Sync
Input/
Output
BNR#
C2
Common Clk
Input/
Output
D08#
A10
Source Sync
Input/
Output
BPM0#
AJ2
Common Clk
Input/
Output
D09#
A11
Source Sync
Input/
Output
BPM1#
AJ1
Common Clk
Output
D10#
B10
Source Sync
Input/
Output
BPM2#
AD2
Common Clk
Output
D11#
C11
Source Sync
BPM3#
AG2
Common Clk
Input/
Output
Input/
Output
D12#
D8
Source Sync
BPM4#
AF2
Common Clk
Output
Input/
Output
BPM5#
AG3
Common Clk
Input/
Output
D13#
B12
Source Sync
Input/
Output
BPMb0#
G1
Common Clk
Input/
Output
D14#
C12
Source Sync
Input/
Output
BPMb1#
C9
Common Clk
Output
D15#
D11
Source Sync
Input/
Output
D16#
G9
Source Sync
Input/
Output
D17#
F8
Source Sync
Input/
Output
BPMb2#
G4
Common Clk
Output
BPMb3#
G3
Common Clk
Input/
Output
BPRI#
G8
Common Clk
Input
BR0#
F3
Common Clk
Input/
Output
D18#
F9
Source Sync
Input/
Output
BR1#
H5
Common Clk
Input
D19#
E9
Source Sync
BSEL0
G29
CMOS
Asynchronous
Output
Input/
Output
D20#
D7
Source Sync
BSEL1
H30
CMOS
Asynchronous
Output
Input/
Output
D21#
E10
Source Sync
BSEL2
G30
CMOS
Asynchronous
Output
Input/
Output
D22#
D10
Source Sync
COMP0
A13
Power/Other
Input
Input/
Output
COMP1
T1
Power/Other
Input
D23#
F11
Source Sync
Input/
Output
COMP2
G2
Power/Other
Input
D24#
F12
Source Sync
COMP3
R1
Power/Other
Input
Input/
Output
D00#
B4
Source Sync
Input/
Output
D25#
D13
Source Sync
Input/
Output
D26#
E13
Source Sync
Input/
Output
58
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 5 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
Table 4-1. Land Listing by Land Name
(Sheet 6 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
D27#
G13
Source Sync
Input/
Output
D53#
B15
Source Sync
Input/
Output
D28#
F14
Source Sync
Input/
Output
D54#
C18
Source Sync
Input/
Output
D29#
G14
Source Sync
Input/
Output
D55#
B16
Source Sync
Input/
Output
D30#
F15
Source Sync
Input/
Output
D56#
A17
Source Sync
Input/
Output
D31#
G15
Source Sync
Input/
Output
D57#
B18
Source Sync
Input/
Output
D32#
G16
Source Sync
Input/
Output
D58#
C21
Source Sync
Input/
Output
D33#
E15
Source Sync
Input/
Output
D59#
B21
Source Sync
Input/
Output
D34#
E16
Source Sync
Input/
Output
D60#
B19
Source Sync
Input/
Output
D35#
G18
Source Sync
Input/
Output
D61#
A19
Source Sync
Input/
Output
D36#
G17
Source Sync
Input/
Output
D62#
A22
Source Sync
Input/
Output
D37#
F17
Source Sync
Input/
Output
D63#
B22
Source Sync
Input/
Output
D38#
F18
Source Sync
Input/
Output
DBI0#
A8
Source Sync
Input/
Output
D39#
E18
Source Sync
Input/
Output
DBI1#
G11
Source Sync
Input/
Output
D40#
E19
Source Sync
Input/
Output
DBI2#
D19
Source Sync
Input/
Output
D41#
F20
Source Sync
Input/
Output
DBI3#
C20
Source Sync
Input/
Output
D42#
E21
Source Sync
Input/
Output
DBR#
AC2
Power/Other
Output
DBSY#
B2
Common Clk
Input/
Output
DEFER#
G7
Common Clk
Input
DP0#
J16
Common Clk
Input/
Output
D43#
F21
Source Sync
Input/
Output
D44#
G21
Source Sync
Input/
Output
D45#
E22
Source Sync
Input/
Output
DP1#
H15
Common Clk
D46#
D22
Source Sync
Input/
Output
Input/
Output
DP2#
H16
Common Clk
D47#
G22
Source Sync
Input/
Output
Input/
Output
DP3#
J17
Common Clk
D48#
D20
Source Sync
Input/
Output
Input/
Output
DRDY#
C1
Common Clk
D49#
D17
Source Sync
Input/
Output
Input/
Output
DSTBN0#
C8
Source Sync
D50#
A14
Source Sync
Input/
Output
Input/
Output
DSTBN1#
G12
Source Sync
D51#
C15
Source Sync
Input/
Output
Input/
Output
DSTBN2#
G20
Source Sync
D52#
C14
Source Sync
Input/
Output
Input/
Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
59
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 7 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
Table 4-1. Land Listing by Land Name
(Sheet 8 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
DSTBN3#
A16
Source Sync
Input/
Output
REQ1#
J5
Source Sync
Input/
Output
DSTBP0#
B9
Source Sync
Input/
Output
REQ2#
M6
Source Sync
Input/
Output
DSTBP1#
E12
Source Sync
Input/
Output
REQ3#
K6
Source Sync
Input/
Output
DSTBP2#
G19
Source Sync
Input/
Output
REQ4#
J6
Source Sync
Input/
Output
DSTBP3#
C17
Source Sync
Input/
Output
RESERVED
A20
FERR#/PBE#
R3
Open Drain
Asynchronous
Output
RESERVED
A23
RESERVED
A24
FORCEPR#
AK6
CMOS
Asynchronous
Input
RESERVED
AC4
RESERVED
AE3
RESERVED
AE4
RESERVED
AE6
RESERVED
AH2
RESERVED
AH7
RESERVED
AJ3
RESERVED
AJ7
RESERVED
AK1
RESERVED
AK3
GTLREF_ADD_END
G10
Power/Other
Input
GTLREF_ADD_MID
F2
Power/Other
Input
GTLREF_DATA_END
H1
Power/Other
Input
GTLREF_DATA_MID
H2
Power/Other
Input
HIT#
D4
Common Clk
Input/
Output
HITM#
E4
Common Clk
Input/
Output
IERR#
AB2
Open Drain
Asynchronous
Output
IGNNE#
N2
CMOS
Asynchronous
Input
INIT#
P3
CMOS
Asynchronous
Input
CMOS
Asynchronous
Input
LINT0
K1
LINT1
L1
CMOS
Asynchronous
Input
LL_ID0
V2
Power/Other
Output
LL_ID1
AA2
Power/Other
Output
LOCK#
C3
Common Clk
Input/
Output
MCERR#
AB3
Common Clk
Input/
Output
RESERVED
AL1
RESERVED
AM2
RESERVED
AM6
RESERVED
AN5
RESERVED
AN6
RESERVED
B13
RESERVED
B23
RESERVED
C23
RESERVED
D1
RESERVED
D14
RESERVED
D16
RESERVED
E1
MS_ID0
W1
Power/Other
Output
RESERVED
E23
MS_ID1
V1
Power/Other
Output
RESERVED
E24
PECI
G5
Power/Other
Input/
Output
RESERVED
E29
RESERVED
E5
RESERVED
E6
RESERVED
E7
RESERVED
F23
RESERVED
F29
RESERVED
F6
PROCHOT#
AL2
Open Drain
Asynchronous
Output
PWRGOOD
N1
CMOS
Asynchronous
Input
REQ0#
K4
Source Sync
Input/
Output
60
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 9 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 10 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
RESERVED
G6
VCC
AC26
Power/Other
RESERVED
J2
VCC
AC27
Power/Other
RESERVED
J3
VCC
AC28
Power/Other
RESERVED
N5
VCC
AC29
Power/Other
RESERVED
T2
VCC
AC30
Power/Other
RESERVED
Y1
VCC
AC8
Power/Other
RESERVED
Y3
VCC
AD23
Power/Other
RESET#
G23
Common Clk
Input
VCC
AD24
Power/Other
RS0#
B3
Common Clk
Input
VCC
AD25
Power/Other
RS1#
F5
Common Clk
Input
VCC
AD26
Power/Other
RS2#
A3
Common Clk
Input
VCC
AD27
Power/Other
RSP#
H4
Common Clk
Input
VCC
AD28
Power/Other
SKTOCC#
AE8
Power/Other
Output
VCC
AD29
Power/Other
SMI#
P2
CMOS
Asynchronous
Input
VCC
AD30
Power/Other
CMOS
Asynchronous
Input
VCC
AD8
Power/Other
VCC
AE11
Power/Other
AE12
Power/Other
STPCLK#
M3
TCK
AE1
TAP
Input
VCC
TDI
AD1
TAP
Input
VCC
AE14
Power/Other
AE15
Power/Other
TDO
AF1
TAP
Output
VCC
TESTHI00
F26
Power/Other
Input
VCC
AE18
Power/Other
AE19
Power/Other
TESTHI01
W3
Power/Other
Input
VCC
TESTHI02
F25
Power/Other
Input
VCC
AE21
Power/Other
AE22
Power/Other
TESTHI03
G25
Power/Other
Input
VCC
TESTHI04
G27
Power/Other
Input
VCC
AE23
Power/Other
AE9
Power/Other
TESTHI05
G26
Power/Other
Input
VCC
TESTHI06
G24
Power/Other
Input
VCC
AF11
Power/Other
AF12
Power/Other
TESTHI07
F24
Power/Other
Input
VCC
TESTHI10
P1
Power/Other
Input
VCC
AF14
Power/Other
AF15
Power/Other
TESTHI11
L2
Power/Other
Input
VCC
TESTIN1
W2
Power/Other
Input
VCC
AF18
Power/Other
AF19
Power/Other
TESTIN2
U1
Power/Other
Input
VCC
THERMTRIP#
M2
Open Drain
Asynchronous
Output
VCC
AF21
Power/Other
VCC
AF22
Power/Other
VCC
AF8
Power/Other
VCC
AF9
Power/Other
VCC
AG11
Power/Other
VCC
AG12
Power/Other
VCC
AG14
Power/Other
VCC
AG15
Power/Other
VCC
AG18
Power/Other
TMS
AC1
TAP
Input
TRDY#
E3
Common Clk
Input
TRST#
AG1
TAP
Input
VCC
AA8
Power/Other
VCC
AB8
Power/Other
VCC
AC23
Power/Other
VCC
AC24
Power/Other
VCC
AC25
Power/Other
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Direction
61
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 11 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 12 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
VCC
AG19
Power/Other
VCC
AK12
Power/Other
VCC
AG21
Power/Other
VCC
AK14
Power/Other
VCC
AG22
Power/Other
VCC
AK15
Power/Other
VCC
AG25
Power/Other
VCC
AK18
Power/Other
VCC
AG26
Power/Other
VCC
AK19
Power/Other
VCC
AG27
Power/Other
VCC
AK21
Power/Other
VCC
AG28
Power/Other
VCC
AK22
Power/Other
VCC
AG29
Power/Other
VCC
AK25
Power/Other
VCC
AG30
Power/Other
VCC
AK26
Power/Other
VCC
AG8
Power/Other
VCC
AK8
Power/Other
VCC
AG9
Power/Other
VCC
AK9
Power/Other
VCC
AH11
Power/Other
VCC
AL11
Power/Other
VCC
AH12
Power/Other
VCC
AL12
Power/Other
VCC
AH14
Power/Other
VCC
AL14
Power/Other
VCC
AH15
Power/Other
VCC
AL15
Power/Other
VCC
AH18
Power/Other
VCC
AL18
Power/Other
VCC
AH19
Power/Other
VCC
AL19
Power/Other
VCC
AH21
Power/Other
VCC
AL21
Power/Other
VCC
AH22
Power/Other
VCC
AL22
Power/Other
VCC
AH25
Power/Other
VCC
AL25
Power/Other
VCC
AH26
Power/Other
VCC
AL26
Power/Other
VCC
AH27
Power/Other
VCC
AL29
Power/Other
VCC
AH28
Power/Other
VCC
AL30
Power/Other
VCC
AH29
Power/Other
VCC
AL9
Power/Other
VCC
AH30
Power/Other
VCC
AM11
Power/Other
VCC
AH8
Power/Other
VCC
AM12
Power/Other
VCC
AH9
Power/Other
VCC
AM14
Power/Other
VCC
AJ11
Power/Other
VCC
AM15
Power/Other
VCC
AJ12
Power/Other
VCC
AM18
Power/Other
VCC
AJ14
Power/Other
VCC
AM19
Power/Other
VCC
AJ15
Power/Other
VCC
AM21
Power/Other
VCC
AJ18
Power/Other
VCC
AM22
Power/Other
VCC
AJ19
Power/Other
VCC
AM25
Power/Other
VCC
AJ21
Power/Other
VCC
AM26
Power/Other
VCC
AJ22
Power/Other
VCC
AM29
Power/Other
VCC
AJ25
Power/Other
VCC
AM30
Power/Other
VCC
AJ26
Power/Other
VCC
AM8
Power/Other
VCC
AJ8
Power/Other
VCC
AM9
Power/Other
VCC
AJ9
Power/Other
VCC
AN11
Power/Other
VCC
AK11
Power/Other
VCC
AN12
Power/Other
62
Direction
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 13 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 14 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
VCC
AN14
Power/Other
VCC
L8
Power/Other
VCC
AN15
Power/Other
VCC
M23
Power/Other
VCC
AN18
Power/Other
VCC
M24
Power/Other
VCC
AN19
Power/Other
VCC
M25
Power/Other
VCC
AN21
Power/Other
VCC
M26
Power/Other
VCC
AN22
Power/Other
VCC
M27
Power/Other
VCC
AN25
Power/Other
VCC
M28
Power/Other
VCC
AN26
Power/Other
VCC
M29
Power/Other
VCC
AN8
Power/Other
VCC
M30
Power/Other
VCC
AN9
Power/Other
VCC
M8
Power/Other
VCC
J10
Power/Other
VCC
N23
Power/Other
VCC
J11
Power/Other
VCC
N24
Power/Other
VCC
J12
Power/Other
VCC
N25
Power/Other
VCC
J13
Power/Other
VCC
N26
Power/Other
VCC
J14
Power/Other
VCC
N27
Power/Other
VCC
J15
Power/Other
VCC
N28
Power/Other
VCC
J18
Power/Other
VCC
N29
Power/Other
VCC
J19
Power/Other
VCC
N30
Power/Other
VCC
J20
Power/Other
VCC
N8
Power/Other
VCC
J21
Power/Other
VCC
P8
Power/Other
VCC
J22
Power/Other
VCC
R8
Power/Other
VCC
J23
Power/Other
VCC
T23
Power/Other
VCC
J24
Power/Other
VCC
T24
Power/Other
VCC
J25
Power/Other
VCC
T25
Power/Other
VCC
J26
Power/Other
VCC
T26
Power/Other
VCC
J27
Power/Other
VCC
T27
Power/Other
VCC
J28
Power/Other
VCC
T28
Power/Other
VCC
J29
Power/Other
VCC
T29
Power/Other
VCC
J30
Power/Other
VCC
T30
Power/Other
VCC
J8
Power/Other
VCC
T8
Power/Other
VCC
J9
Power/Other
VCC
U23
Power/Other
VCC
K23
Power/Other
VCC
U24
Power/Other
VCC
K24
Power/Other
VCC
U25
Power/Other
VCC
K25
Power/Other
VCC
U26
Power/Other
VCC
K26
Power/Other
VCC
U27
Power/Other
VCC
K27
Power/Other
VCC
U28
Power/Other
VCC
K28
Power/Other
VCC
U29
Power/Other
VCC
K29
Power/Other
VCC
U30
Power/Other
VCC
K30
Power/Other
VCC
U8
Power/Other
VCC
K8
Power/Other
VCC
V8
Power/Other
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Direction
63
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 15 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 16 of 23)
Direction
Pin Name
Pin
No.
AA28
Signal
Buffer Type
VCC
W23
Power/Other
VSS
VCC
W24
Power/Other
VSS
AA29
Power/Other
VCC
W25
Power/Other
VSS
AA3
Power/Other
VCC
W26
Power/Other
VSS
AA30
Power/Other
VCC
W27
Power/Other
VSS
AA6
Power/Other
VCC
W28
Power/Other
VSS
AA7
Power/Other
VCC
W29
Power/Other
VSS
AB1
Power/Other
Power/Other
VCC
W30
Power/Other
VSS
AB23
Power/Other
VCC
W8
Power/Other
VSS
AB24
Power/Other
VCC
Y23
Power/Other
VSS
AB25
Power/Other
VCC
Y24
Power/Other
VSS
AB26
Power/Other
VCC
Y25
Power/Other
VSS
AB27
Power/Other
VCC
Y26
Power/Other
VSS
AB28
Power/Other
VCC
Y27
Power/Other
VSS
AB29
Power/Other
VCC
Y28
Power/Other
VSS
AB30
Power/Other
VCC
Y29
Power/Other
VSS
AB7
Power/Other
VCC
Y30
Power/Other
VSS
AC3
Power/Other
VCC
Y8
Power/Other
VSS
AC6
Power/Other
VCC_DIE_SENSE
AN3
Power/Other
Output
VSS
AC7
Power/Other
VCC_DIE_SENSE2
AL8
Power/Other
Output
VSS
AD4
Power/Other
VCCPLL
D23
Power/Other
Input
VSS
AD7
Power/Other
VID_SELECT
AN7
Power/Other
Output
VSS
AE10
Power/Other
VID1
AL5
Power/Other
Output
VSS
AE13
Power/Other
VID2
AM3
Power/Other
Output
VSS
AE16
Power/Other
VID3
AL6
Power/Other
Output
VSS
AE17
Power/Other
VID4
AK4
Power/Other
Output
VSS
AE2
Power/Other
VID5
AL4
Power/Other
Output
VSS
AE20
Power/Other
VID6
AM5
Power/Other
Output
VSS
AE24
Power/Other
VSS
A12
Power/Other
VSS
AE25
Power/Other
VSS
A15
Power/Other
VSS
AE26
Power/Other
VSS
A18
Power/Other
VSS
AE27
Power/Other
VSS
A2
Power/Other
VSS
AE28
Power/Other
VSS
A21
Power/Other
VSS
AE29
Power/Other
VSS
A6
Power/Other
VSS
AE30
Power/Other
VSS
A9
Power/Other
VSS
AE5
Power/Other
VSS
AA23
Power/Other
VSS
AE7
Power/Other
VSS
AA24
Power/Other
VSS
AF10
Power/Other
VSS
AA25
Power/Other
VSS
AF13
Power/Other
VSS
AA26
Power/Other
VSS
AF16
Power/Other
VSS
AA27
Power/Other
VSS
AF17
Power/Other
64
Direction
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 17 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 18 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
VSS
AF20
Power/Other
VSS
AJ30
VSS
AF23
Power/Other
VSS
AJ4
Power/Other
VSS
AF24
Power/Other
VSS
AK10
Power/Other
VSS
AF25
Power/Other
VSS
AK13
Power/Other
VSS
AF26
Power/Other
VSS
AK16
Power/Other
VSS
AF27
Power/Other
VSS
AK17
Power/Other
VSS
AF28
Power/Other
VSS
AK2
Power/Other
VSS
AF29
Power/Other
VSS
AK20
Power/Other
VSS
AF3
Power/Other
VSS
AK23
Power/Other
VSS
AF30
Power/Other
VSS
AK24
Power/Other
VSS
AF6
Power/Other
VSS
AK27
Power/Other
VSS
AF7
Power/Other
VSS
AK28
Power/Other
VSS
AG10
Power/Other
VSS
AK29
Power/Other
VSS
AG13
Power/Other
VSS
AK30
Power/Other
VSS
AG16
Power/Other
VSS
AK5
Power/Other
VSS
AG17
Power/Other
VSS
AK7
Power/Other
VSS
AG20
Power/Other
VSS
AL10
Power/Other
VSS
AG23
Power/Other
VSS
AL13
Power/Other
VSS
AG24
Power/Other
VSS
AL16
Power/Other
VSS
AG7
Power/Other
VSS
AL17
Power/Other
VSS
AH1
Power/Other
VSS
AL20
Power/Other
VSS
AH10
Power/Other
VSS
AL23
Power/Other
VSS
AH13
Power/Other
VSS
AL24
Power/Other
VSS
AH16
Power/Other
VSS
AL27
Power/Other
VSS
AH17
Power/Other
VSS
AL28
Power/Other
VSS
AH20
Power/Other
VSS
AL3
Power/Other
VSS
AH23
Power/Other
VSS
AM1
Power/Other
VSS
AH24
Power/Other
VSS
AM10
Power/Other
VSS
AH3
Power/Other
VSS
AM13
Power/Other
VSS
AH6
Power/Other
VSS
AM16
Power/Other
VSS
AJ10
Power/Other
VSS
AM17
Power/Other
VSS
AJ13
Power/Other
VSS
AM20
Power/Other
VSS
AJ16
Power/Other
VSS
AM23
Power/Other
VSS
AJ17
Power/Other
VSS
AM24
Power/Other
VSS
AJ20
Power/Other
VSS
AM27
Power/Other
VSS
AJ23
Power/Other
VSS
AM28
Power/Other
VSS
AJ24
Power/Other
VSS
AM4
Power/Other
VSS
AJ27
Power/Other
VSS
AM7
Power/Other
VSS
AJ28
Power/Other
VSS
AN1
Power/Other
VSS
AJ29
Power/Other
VSS
AN10
Power/Other
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Direction
Power/Other
65
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 19 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 20 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
VSS
AN13
Power/Other
VSS
E28
Power/Other
VSS
AN16
Power/Other
VSS
E8
Power/Other
VSS
AN17
Power/Other
VSS
F1
Power/Other
VSS
AN2
Power/Other
VSS
F10
Power/Other
VSS
AN20
Power/Other
VSS
F13
Power/Other
VSS
AN23
Power/Other
VSS
F16
Power/Other
VSS
AN24
Power/Other
VSS
F19
Power/Other
VSS
B1
Power/Other
VSS
F22
Power/Other
VSS
B11
Power/Other
VSS
F4
Power/Other
VSS
B14
Power/Other
VSS
F7
Power/Other
VSS
B17
Power/Other
VSS
H10
Power/Other
VSS
B20
Power/Other
VSS
H11
Power/Other
VSS
B24
Power/Other
VSS
H12
Power/Other
VSS
B5
Power/Other
VSS
H13
Power/Other
VSS
B8
Power/Other
VSS
H14
Power/Other
VSS
C10
Power/Other
VSS
H17
Power/Other
VSS
C13
Power/Other
VSS
H18
Power/Other
VSS
C16
Power/Other
VSS
H19
Power/Other
VSS
C19
Power/Other
VSS
H20
Power/Other
VSS
C22
Power/Other
VSS
H21
Power/Other
VSS
C24
Power/Other
VSS
H22
Power/Other
VSS
C4
Power/Other
VSS
H23
Power/Other
VSS
C7
Power/Other
VSS
H24
Power/Other
VSS
D12
Power/Other
VSS
H25
Power/Other
VSS
D15
Power/Other
VSS
H26
Power/Other
VSS
D18
Power/Other
VSS
H27
Power/Other
VSS
D21
Power/Other
VSS
H28
Power/Other
VSS
D24
Power/Other
VSS
H29
Power/Other
VSS
D3
Power/Other
VSS
H3
Power/Other
VSS
D5
Power/Other
VSS
H6
Power/Other
VSS
D6
Power/Other
VSS
H7
Power/Other
VSS
D9
Power/Other
VSS
H8
Power/Other
VSS
E11
Power/Other
VSS
H9
Power/Other
VSS
E14
Power/Other
VSS
J4
Power/Other
VSS
E17
Power/Other
VSS
J7
Power/Other
VSS
E2
Power/Other
VSS
K2
Power/Other
VSS
E20
Power/Other
VSS
K5
Power/Other
VSS
E25
Power/Other
VSS
K7
Power/Other
VSS
E26
Power/Other
VSS
L23
Power/Other
VSS
E27
Power/Other
VSS
L24
Power/Other
66
Direction
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 21 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Table 4-1. Land Listing by Land Name
(Sheet 22 of 23)
Direction
Pin Name
Pin
No.
Signal
Buffer Type
Direction
VSS
L25
Power/Other
VSS
V24
Power/Other
VSS
L26
Power/Other
VSS
V25
Power/Other
VSS
L27
Power/Other
VSS
V26
Power/Other
VSS
L28
Power/Other
VSS
V27
Power/Other
VSS
L29
Power/Other
VSS
V28
Power/Other
VSS
L3
Power/Other
VSS
V29
Power/Other
VSS
L30
Power/Other
VSS
V3
Power/Other
VSS
L6
Power/Other
VSS
V30
Power/Other
VSS
L7
Power/Other
VSS
V6
Power/Other
VSS
M1
Power/Other
VSS
V7
Power/Other
VSS
M7
Power/Other
VSS
W4
Power/Other
VSS
N3
Power/Other
VSS
W7
Power/Other
VSS
N6
Power/Other
VSS
Y2
Power/Other
VSS
N7
Power/Other
VSS
Y5
Power/Other
VSS
P23
Power/Other
VSS
Y7
Power/Other
VSS
P24
Power/Other
VSS_DIE_SENSE
AN4
Power/Other
Output
VSS
P25
Power/Other
VSS_DIE_SENSE2
AL7
Power/Other
Output
VSS
P26
Power/Other
VTT
A25
Power/Other
VSS
P27
Power/Other
VTT
A26
Power/Other
VSS
P28
Power/Other
VTT
B25
Power/Other
VSS
P29
Power/Other
VTT
B26
Power/Other
VSS
P30
Power/Other
VTT
B27
Power/Other
VSS
P4
Power/Other
VTT
B28
Power/Other
VSS
P7
Power/Other
VTT
B29
Power/Other
VSS
R2
Power/Other
VTT
B30
Power/Other
VSS
R23
Power/Other
VTT
C25
Power/Other
VSS
R24
Power/Other
VTT
C26
Power/Other
VSS
R25
Power/Other
VTT
C27
Power/Other
VSS
R26
Power/Other
VTT
C28
Power/Other
VSS
R27
Power/Other
VTT
C29
Power/Other
VSS
R28
Power/Other
VTT
C30
Power/Other
VSS
R29
Power/Other
VTT
D25
Power/Other
VSS
R30
Power/Other
VTT
D26
Power/Other
VSS
R5
Power/Other
VTT
D27
Power/Other
VSS
R7
Power/Other
VTT
D28
Power/Other
VSS
T3
Power/Other
VTT
D29
Power/Other
VSS
T6
Power/Other
VTT
D30
Power/Other
VSS
T7
Power/Other
VTT
E30
Power/Other
VSS
U7
Power/Other
VTT
F30
Power/Other
VSS
V23
Power/Other
VTT_OUT
AA1
Power/Other
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Output
67
Land Listing
Table 4-1. Land Listing by Land Name
(Sheet 23 of 23)
Pin Name
Pin
No.
Signal
Buffer Type
Direction
VTT_OUT
J1
Power/Other
Output
VTT_SEL
F27
Power/Other
Output
68
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
4.1.2
Land Listing by Land Number
Table 4-2. Land Listing by Land Number
(Sheet 1 of 20)
Pin
No.
A10
Pin Name
D08#
Signal
Buffer Type
Source Sync
Direction
Table 4-2. Land Listing by Land Number
(Sheet 2 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Input/Output
AA7
VSS
Power/Other
Input/Output
AA8
VCC
Power/Other
Direction
A11
D09#
Source Sync
A12
VSS
Power/Other
AB1
VSS
Power/Other
AB2
IERR#
Open Drain
Asynchronous
AB23
VSS
Power/Other
AB24
VSS
Power/Other
AB25
VSS
Power/Other
AB26
VSS
Power/Other
AB27
VSS
Power/Other
AB28
VSS
Power/Other
AB29
VSS
Power/Other
AB3
MCERR#
Common Clk
AB30
VSS
Power/Other
AB4
A26#
Source Sync
Input/Output
AB5
A24#
Source Sync
Input/Output
AB6
A17#
Source Sync
Input/Output
AB7
VSS
Power/Other
AB8
VCC
Power/Other
AC1
TMS
TAP
Input
AC2
DBR#
Power/Other
Output
AC23
VCC
Power/Other
AC24
VCC
Power/Other
AC25
VCC
Power/Other
AC26
VCC
Power/Other
AC27
VCC
Power/Other
AC28
VCC
Power/Other
AC29
VCC
Power/Other
AC3
VSS
Power/Other
AC30
VCC
Power/Other
AC4
RESERVED
AC5
A25#
Source Sync
AC6
VSS
Power/Other
A13
COMP0
Power/Other
Input
A14
D50#
Source Sync
Input/Output
A15
VSS
Power/Other
A16
DSTBN3#
Source Sync
Input/Output
A17
D56#
Source Sync
Input/Output
A18
VSS
Power/Other
A19
D61#
Source Sync
A2
VSS
Power/Other
A20
RESERVED
A21
VSS
Power/Other
A22
D62#
Source Sync
A23
RESERVED
A24
RESERVED
A25
VTT
Power/Other
A26
VTT
Power/Other
A3
RS2#
Common Clk
Input
A4
D02#
Source Sync
Input/Output
A5
D04#
Source Sync
Input/Output
A6
VSS
Power/Other
A7
D07#
Source Sync
Input/Output
A8
DBI0#
Source Sync
Input/Output
A9
VSS
Power/Other
AA1
VTT_OUT
Power/Other
Output
AA2
LL_ID1
Power/Other
Output
AA23
VSS
Power/Other
AA24
VSS
Power/Other
AA25
VSS
Power/Other
AA26
VSS
Power/Other
AA27
VSS
Power/Other
AA28
VSS
Power/Other
AA29
VSS
Power/Other
AA3
VSS
Power/Other
AA30
VSS
Power/Other
AA4
A21#
Source Sync
Input/Output
AA5
A23#
Source Sync
Input/Output
AA6
VSS
Power/Other
Input/Output
Input/Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Output
Input/Output
Input/Output
AC7
VSS
Power/Other
AC8
VCC
Power/Other
AD1
TDI
TAP
Input
AD2
BPM2#
Common Clk
Output
AD23
VCC
Power/Other
AD24
VCC
Power/Other
69
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 3 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 4 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
AD25
VCC
Power/Other
AE8
SKTOCC#
Power/Other
AD26
VCC
Power/Other
AE9
VCC
Power/Other
AD27
VCC
Power/Other
AF1
TDO
TAP
AD28
VCC
Power/Other
AF10
VSS
Power/Other
AD29
VCC
Power/Other
AF11
VCC
Power/Other
AD3
BINIT#
Common Clk
AF12
VCC
Power/Other
AD30
VCC
Power/Other
AF13
VSS
Power/Other
Input/Output
AD4
VSS
Power/Other
AF14
VCC
Power/Other
AD5
ADSTB1#
Source Sync
Input/Output
AF15
VCC
Power/Other
AD6
A22#
Source Sync
Input/Output
AF16
VSS
Power/Other
AD7
VSS
Power/Other
AF17
VSS
Power/Other
AF18
VCC
Power/Other
AF19
VCC
Power/Other
AD8
VCC
Power/Other
AE1
TCK
TAP
AE10
VSS
Power/Other
AF2
BPM4#
Common Clk
AE11
VCC
Power/Other
AF20
VSS
Power/Other
AE12
VCC
Power/Other
AF21
VCC
Power/Other
AE13
VSS
Power/Other
AF22
VCC
Power/Other
AE14
VCC
Power/Other
AF23
VSS
Power/Other
AE15
VCC
Power/Other
AF24
VSS
Power/Other
AE16
VSS
Power/Other
AF25
VSS
Power/Other
AE17
VSS
Power/Other
AF26
VSS
Power/Other
AE18
VCC
Power/Other
AF27
VSS
Power/Other
AE19
VCC
Power/Other
AF28
VSS
Power/Other
Input
Direction
Output
Output
Output
AE2
VSS
Power/Other
AF29
VSS
Power/Other
AE20
VSS
Power/Other
AF3
VSS
Power/Other
AE21
VCC
Power/Other
AF30
VSS
Power/Other
AE22
VCC
Power/Other
AF4
A28#
Source Sync
Input/Output
AE23
VCC
Power/Other
AF5
A27#
Source Sync
Input/Output
AE24
VSS
Power/Other
AF6
VSS
Power/Other
AE25
VSS
Power/Other
AF7
VSS
Power/Other
AE26
VSS
Power/Other
AF8
VCC
Power/Other
AE27
VSS
Power/Other
AF9
VCC
Power/Other
AE28
VSS
Power/Other
AG1
TRST#
TAP
AE29
VSS
Power/Other
AG10
VSS
Power/Other
AE3
RESERVED
AG11
VCC
Power/Other
AE30
VSS
AG12
VCC
Power/Other
AE4
RESERVED
AG13
VSS
Power/Other
AG14
VCC
Power/Other
AG15
VCC
Power/Other
AG16
VSS
Power/Other
AE5
VSS
AE6
RESERVED
AE7
VSS
70
Power/Other
Power/Other
Power/Other
Input
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 5 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 6 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
AG17
VSS
Power/Other
AH26
VCC
Power/Other
AG18
VCC
Power/Other
AH27
VCC
Power/Other
AG19
VCC
Power/Other
AH28
VCC
Power/Other
Input/Output
Direction
AG2
BPM3#
Common Clk
AH29
VCC
Power/Other
AG20
VSS
Power/Other
AH3
VSS
Power/Other
AG21
VCC
Power/Other
AH30
VCC
Power/Other
AG22
VCC
Power/Other
AH4
A32#
Source Sync
Input/Output
AG23
VSS
Power/Other
AH5
A33#
Source Sync
Input/Output
AG24
VSS
Power/Other
AH6
VSS
Power/Other
AG25
VCC
Power/Other
AH7
RESERVED
AG26
VCC
Power/Other
AH8
VCC
Power/Other
AG27
VCC
Power/Other
AH9
VCC
Power/Other
AG28
VCC
Power/Other
AJ1
BPM1#
Common Clk
AG29
VCC
Power/Other
AJ10
VSS
Power/Other
AG3
BPM5#
Common Clk
AJ11
VCC
Power/Other
AG30
VCC
Power/Other
AJ12
VCC
Power/Other
AG4
A30#
Source Sync
Input/Output
AJ13
VSS
Power/Other
AG5
A31#
Source Sync
Input/Output
AJ14
VCC
Power/Other
AG6
A29#
Source Sync
Input/Output
AJ15
VCC
Power/Other
AG7
VSS
Power/Other
AJ16
VSS
Power/Other
AG8
VCC
Power/Other
AJ17
VSS
Power/Other
AG9
VCC
Power/Other
AJ18
VCC
Power/Other
AH1
VSS
Power/Other
AJ19
VCC
Power/Other
AH10
VSS
Power/Other
AJ2
BPM0#
Common Clk
AH11
VCC
Power/Other
AJ20
VSS
Power/Other
AH12
VCC
Power/Other
AJ21
VCC
Power/Other
AH13
VSS
Power/Other
AJ22
VCC
Power/Other
AH14
VCC
Power/Other
AJ23
VSS
Power/Other
AH15
VCC
Power/Other
AJ24
VSS
Power/Other
AH16
VSS
Power/Other
AJ25
VCC
Power/Other
AH17
VSS
Power/Other
AJ26
VCC
Power/Other
AH18
VCC
Power/Other
AJ27
VSS
Power/Other
AH19
VCC
Power/Other
AJ28
VSS
Power/Other
Power/Other
Input/Output
Output
Input/Output
AH2
RESERVED
AJ29
VSS
AH20
VSS
Power/Other
AJ3
RESERVED
AH21
VCC
Power/Other
AJ30
VSS
Power/Other
AH22
VCC
Power/Other
AJ4
VSS
Power/Other
AH23
VSS
Power/Other
AJ5
A34#
Source Sync
Input/Output
AH24
VSS
Power/Other
AJ6
A35#
Source Sync
Input/Output
AH25
VCC
Power/Other
AJ7
RESERVED
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
71
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 7 of 20)
Pin
No.
AJ8
Pin Name
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 8 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
VCC
Power/Other
AL17
VSS
Power/Other
AJ9
VCC
Power/Other
AL18
VCC
Power/Other
AK1
RESERVED
AL19
VCC
Power/Other
AK10
VSS
Power/Other
AL2
PROCHOT#
AK11
VCC
Power/Other
Open Drain
Asynchronous
AK12
VCC
Power/Other
AL20
VSS
Power/Other
AK13
VSS
Power/Other
AL21
VCC
Power/Other
AK14
VCC
Power/Other
AL22
VCC
Power/Other
AK15
VCC
Power/Other
AL23
VSS
Power/Other
AK16
VSS
Power/Other
AL24
VSS
Power/Other
AK17
VSS
Power/Other
AL25
VCC
Power/Other
AK18
VCC
Power/Other
AL26
VCC
Power/Other
AK19
VCC
Power/Other
AL27
VSS
Power/Other
AK2
VSS
Power/Other
AL28
VSS
Power/Other
AK20
VSS
Power/Other
AK21
VCC
Power/Other
AK22
VCC
Power/Other
AK23
VSS
Power/Other
AK24
VSS
Power/Other
AK25
VCC
Power/Other
AK26
VCC
Power/Other
AK27
VSS
Power/Other
AK28
VSS
Power/Other
AK29
VSS
Power/Other
AK3
RESERVED
AK30
VSS
Power/Other
AK4
VID4
Power/Other
AK5
VSS
Power/Other
AK6
FORCEPR#
CMOS
Asynchronous
AK7
VSS
AK8
VCC
AK9
VCC
Power/Other
AL1
RESERVED
AL10
VSS
AL11
VCC
AL12
VCC
AL13
VSS
AL14
AL15
AL16
72
VCC
Power/Other
AL3
VSS
Power/Other
AL30
VCC
Power/Other
AL4
VID5
Power/Other
Output
AL5
VID1
Power/Other
Output
AL6
VID3
Power/Other
Output
VSS_DIE_SENSE2
Power/Other
AL8
VCC_DIE_SENSE2
Power/Other
AL9
VCC
Power/Other
AM1
VSS
Power/Other
AM10
VSS
Power/Other
AM11
VCC
Power/Other
AM12
VCC
Power/Other
AM13
VSS
Power/Other
AM14
VCC
Power/Other
AM15
VCC
Power/Other
Power/Other
AM16
VSS
Power/Other
Power/Other
AM17
VSS
Power/Other
AM18
VCC
Power/Other
AM19
VCC
Power/Other
Power/Other
AM2
RESERVED
Power/Other
AM20
VSS
Power/Other
Power/Other
AM21
VCC
Power/Other
Power/Other
AM22
VCC
Power/Other
VCC
Power/Other
AM23
VSS
Power/Other
VCC
Power/Other
AM24
VSS
Power/Other
VSS
Power/Other
AM25
VCC
Power/Other
Input
Output
AL29
AL7
Output
Direction
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 9 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 10 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
AM26
VCC
Power/Other
B11
VSS
Power/Other
AM27
VSS
Power/Other
B12
D13#
Source Sync
AM28
VSS
Power/Other
B13
RESERVED
AM29
VCC
Power/Other
B14
VSS
Power/Other
AM3
VID2
Power/Other
B15
D53#
Source Sync
Input/Output
AM30
VCC
Power/Other
B16
D55#
Source Sync
Input/Output
AM4
VSS
Power/Other
B17
VSS
Power/Other
AM5
VID6
Power/Other
B18
D57#
Source Sync
Input/Output
AM6
RESERVED
B19
D60#
Source Sync
Input/Output
AM7
VSS
Power/Other
B2
DBSY#
Common Clk
Input/Output
AM8
VCC
Power/Other
B20
VSS
Power/Other
Output
Output
Input/Output
AM9
VCC
Power/Other
B21
D59#
Source Sync
Input/Output
AN1
VSS
Power/Other
B22
D63#
Source Sync
Input/Output
AN10
VSS
Power/Other
B23
RESERVED
AN11
VCC
Power/Other
B24
VSS
Power/Other
AN12
VCC
Power/Other
B25
VTT
Power/Other
AN13
VSS
Power/Other
B26
VTT
Power/Other
AN14
VCC
Power/Other
B27
VTT
Power/Other
AN15
VCC
Power/Other
B28
VTT
Power/Other
AN16
VSS
Power/Other
B29
VTT
Power/Other
AN17
VSS
Power/Other
B3
RS0#
Common Clk
AN18
VCC
Power/Other
B30
VTT
Power/Other
AN19
VCC
Power/Other
B4
D00#
Source Sync
Input
Input/Output
AN2
VSS
Power/Other
B5
VSS
Power/Other
AN20
VSS
Power/Other
B6
D05#
Source Sync
Input/Output
AN21
VCC
Power/Other
B7
D06#
Source Sync
Input/Output
AN22
VCC
Power/Other
B8
VSS
Power/Other
AN23
VSS
Power/Other
B9
DSTBP0#
Source Sync
Input/Output
AN24
VSS
Power/Other
C1
DRDY#
Common Clk
Input/Output
AN25
VCC
Power/Other
C10
VSS
Power/Other
AN26
VCC
Power/Other
C11
D11#
Source Sync
Input/Output
AN3
VCC_DIE_SENSE
Power/Other
Output
C12
D14#
Source Sync
Input/Output
AN4
VSS_DIE_SENSE
Power/Other
Output
C13
VSS
Power/Other
AN5
RESERVED
C14
D52#
Source Sync
Input/Output
AN6
RESERVED
C15
D51#
Source Sync
Input/Output
AN7
VID_SELECT
Power/Other
C16
VSS
Power/Other
AN8
VCC
Power/Other
C17
DSTBP3#
Source Sync
Input/Output
Input/Output
Output
AN9
VCC
Power/Other
C18
D54#
Source Sync
B1
VSS
Power/Other
C19
VSS
Power/Other
B10
D10#
Source Sync
C2
BNR#
Common Clk
Input/Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Input/Output
73
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 11 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
C20
DBI3#
C21
C22
C23
RESERVED
C24
VSS
Power/Other
C25
VTT
C26
VTT
C27
C28
Direction
Table 4-2. Land Listing by Land Number
(Sheet 12 of 20)
Pin
No.
Pin Name
Direction
Source Sync
Input/Output
D3
D58#
Source Sync
Input/Output
D30
VTT
Power/Other
VSS
Power/Other
D4
HIT#
Common Clk
D5
VSS
Power/Other
D6
VSS
Power/Other
Power/Other
D7
D20#
Source Sync
Input/Output
Power/Other
D8
D12#
Source Sync
Input/Output
VTT
Power/Other
D9
VSS
Power/Other
VTT
Power/Other
E1
RESERVED
Power/Other
C29
VTT
Power/Other
E10
D21#
Source Sync
C3
LOCK#
Common Clk
E11
VSS
Power/Other
C30
VTT
Power/Other
E12
DSTBP1#
Source Sync
Input/Output
C4
VSS
Power/Other
E13
D26#
Source Sync
Input/Output
C5
D01#
Source Sync
Input/Output
E14
VSS
Power/Other
C6
D03#
Source Sync
Input/Output
E15
D33#
Source Sync
Input/Output
C7
VSS
Power/Other
E16
D34#
Source Sync
Input/Output
C8
DSTBN0#
Source Sync
Input/Output
E17
VSS
Power/Other
C9
BPMb1#
Common Clk
Output
E18
D39#
Source Sync
Input/Output
D1
RESERVED
E19
D40#
Source Sync
Input/Output
D10
D22#
Source Sync
Input/Output
E2
VSS
Power/Other
D11
D15#
Source Sync
Input/Output
E20
VSS
Power/Other
D12
VSS
Power/Other
E21
D42#
Source Sync
Input/Output
D13
D25#
Source Sync
E22
D45#
Source Sync
Input/Output
E23
RESERVED
E24
RESERVED
E25
VSS
Power/Other
E26
VSS
Power/Other
Input/Output
Input/Output
VSS
Signal
Buffer Type
Power/Other
D14
RESERVED
D15
VSS
D16
RESERVED
D17
D49#
Source Sync
D18
VSS
Power/Other
E27
VSS
Power/Other
D19
DBI2#
Source Sync
Input/Output
E28
VSS
Power/Other
D2
ADS#
Common Clk
Input/Output
E29
RESERVED
D20
D48#
Source Sync
Input/Output
E3
TRDY#
D21
VSS
Power/Other
E30
VTT
Power/Other
D22
D46#
Source Sync
Input/Output
E4
HITM#
Common Clk
D23
VCCPLL
Power/Other
Input
E5
RESERVED
D24
VSS
Power/Other
E6
RESERVED
D25
VTT
Power/Other
E7
RESERVED
D26
VTT
Power/Other
E8
VSS
Power/Other
D27
VTT
Power/Other
E9
D19#
Source Sync
D28
VTT
Power/Other
F1
VSS
Power/Other
D29
VTT
Power/Other
F10
VSS
Power/Other
74
Power/Other
Input/Output
Common Clk
Input/Output
Input/Output
Input
Input/Output
Input/Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 13 of 20)
Pin
No.
F11
Pin Name
D23#
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 14 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
Source Sync
Input/Output
G20
DSTBN2#
Source Sync
Input/Output
Input/Output
G21
D44#
Source Sync
Input/Output
G22
D47#
Source Sync
Input/Output
F12
D24#
Source Sync
F13
VSS
Power/Other
F14
D28#
Source Sync
Input/Output
G23
RESET#
Common Clk
Input
F15
D30#
Source Sync
Input/Output
G24
TESTHI06
Power/Other
Input
F16
VSS
Power/Other
G25
TESTHI03
Power/Other
Input
F17
D37#
Source Sync
Input/Output
G26
TESTHI05
Power/Other
Input
Input/Output
G27
TESTHI04
Power/Other
Input
G28
BCLK1
Clk
Input
G29
BSEL0
CMOS
Asynchronous
Output
G3
BPMb3#
Common Clk
Input/Output
G30
BSEL2
CMOS
Asynchronous
Output
F18
D38#
Source Sync
F19
VSS
Power/Other
F2
GTLREF_ADD_MID
Power/Other
Input
F20
D41#
Source Sync
Input/Output
F21
D43#
Source Sync
Input/Output
F22
VSS
Power/Other
F23
RESERVED
G4
BPMb2#
Common Clk
Output
F24
TESTHI07
Power/Other
Input
G5
PECI
Power/Other
Input/Output
F25
TESTHI02
Power/Other
Input
G6
RESERVED
F26
TESTHI00
Power/Other
Input
G7
DEFER#
Common Clk
Input
F27
VTT_SEL
Power/Other
Output
G8
BPRI#
Common Clk
Input
F28
BCLK0
Clk
Input
G9
D16#
Source Sync
Input/Output
F29
RESERVED
H1
GTLREF_DATA_END
Power/Other
Input
F3
BR0#
Common Clk
H10
VSS
Power/Other
F30
VTT
Power/Other
H11
VSS
Power/Other
F4
VSS
Power/Other
H12
VSS
Power/Other
F5
RS1#
Common Clk
H13
VSS
Power/Other
F6
RESERVED
H14
VSS
Power/Other
F7
VSS
Power/Other
H15
DP1#
Common Clk
Input/Output
F8
D17#
Source Sync
Input/Output
H16
DP2#
Common Clk
Input/Output
F9
D18#
Source Sync
Input/Output
H17
VSS
Power/Other
G1
BPMb0#
Power/Other
Input/Output
H18
VSS
Power/Other
G10
GTLREF_ADD_END
Power/Other
Input
H19
VSS
Power/Other
G11
DBI1#
Source Sync
Input/Output
H2
GTLREF_DATA_MID
Power/Other
G12
DSTBN1#
Source Sync
Input/Output
H20
VSS
Power/Other
G13
D27#
Source Sync
Input/Output
H21
VSS
Power/Other
G14
D29#
Source Sync
Input/Output
H22
VSS
Power/Other
G15
D31#
Source Sync
Input/Output
H23
VSS
Power/Other
G16
D32#
Source Sync
Input/Output
H24
VSS
Power/Other
G17
D36#
Source Sync
Input/Output
H25
VSS
Power/Other
G18
D35#
Source Sync
Input/Output
H26
VSS
Power/Other
G19
DSTBP2#
Source Sync
Input/Output
H27
VSS
Power/Other
G2
COMP2
Power/Other
Input
H28
VSS
Power/Other
Input/Output
Input
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Input
75
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 15 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
H29
VSS
Power/Other
H3
VSS
Power/Other
H30
BSEL1
CMOS
Asynchronous
Output
H4
RSP#
Common Clk
H5
BR1#
Common Clk
H6
VSS
H7
VSS
H8
H9
Table 4-2. Land Listing by Land Number
(Sheet 16 of 20)
Pin
No.
K1
Pin Name
LINT0
Signal
Buffer Type
CMOS
Asynchronous
Direction
Input
K2
VSS
Power/Other
K23
VCC
Power/Other
Input
K24
VCC
Power/Other
Input
K25
VCC
Power/Other
Power/Other
K26
VCC
Power/Other
Power/Other
K27
VCC
Power/Other
VSS
Power/Other
K28
VCC
Power/Other
VSS
Power/Other
K29
VCC
Power/Other
J1
VTT_OUT
Power/Other
K3
A20M#
J10
VCC
Power/Other
CMOS
Asynchronous
J11
VCC
Power/Other
K30
VCC
Power/Other
J12
VCC
Power/Other
K4
REQ0#
Source Sync
J13
VCC
Power/Other
K5
VSS
Power/Other
J14
VCC
Power/Other
K6
REQ3#
Source Sync
J15
VCC
Power/Other
K7
VSS
Power/Other
J16
DP0#
Common Clk
Input/Output
K8
VCC
Power/Other
J17
DP3#
Common Clk
Input/Output
L1
LINT1
CMOS
Asynchronous
Input
J18
VCC
Power/Other
L2
TESTHI11
Power/Other
Input
J19
VCC
Power/Other
L23
VSS
Power/Other
J2
RESERVED
L24
VSS
Power/Other
J20
VCC
Power/Other
L25
VSS
Power/Other
J21
VCC
Power/Other
L26
VSS
Power/Other
J22
VCC
Power/Other
L27
VSS
Power/Other
J23
VCC
Power/Other
L28
VSS
Power/Other
J24
VCC
Power/Other
L29
VSS
Power/Other
J25
VCC
Power/Other
L3
VSS
Power/Other
J26
VCC
Power/Other
L30
VSS
Power/Other
J27
VCC
Power/Other
L4
A06#
Source Sync
Input/Output
J28
VCC
Power/Other
L5
A05#
Source Sync
Input/Output
J29
VCC
Power/Other
L6
VSS
Power/Other
J3
RESERVED
L7
VSS
Power/Other
J30
VCC
Power/Other
L8
VCC
Power/Other
J4
VSS
Power/Other
M1
VSS
Power/Other
J5
REQ1#
Source Sync
Input/Output
M2
THERMTRIP#
J6
REQ4#
Source Sync
Input/Output
Open Drain
Asynchronous
J7
VSS
Power/Other
M23
VCC
Power/Other
J8
VCC
Power/Other
M24
VCC
Power/Other
M25
VCC
Power/Other
M26
VCC
Power/Other
J9
76
VCC
Power/Other
Output
Input
Input/Output
Input/Output
Output
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 17 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
Table 4-2. Land Listing by Land Number
(Sheet 18 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Direction
M27
VCC
Power/Other
P5
A37#
Source Sync
Input/Output
M28
VCC
Power/Other
P6
A04#
Source Sync
Input/Output
M29
VCC
Power/Other
P7
VSS
Power/Other
M3
STPCLK#
CMOS
Asynchronous
Input
M30
VCC
Power/Other
M4
A07#
Source Sync
Input/Output
M5
A03#
Source Sync
Input/Output
M6
REQ2#
Source Sync
Input/Output
M7
VSS
Power/Other
M8
VCC
Power/Other
N1
PWRGOOD
CMOS
Asynchronous
Input
Input
P8
VCC
Power/Other
R1
COMP3
Power/Other
R2
VSS
Power/Other
R23
VSS
Power/Other
R24
VSS
Power/Other
R25
VSS
Power/Other
R26
VSS
Power/Other
R27
VSS
Power/Other
R28
VSS
Power/Other
R29
VSS
Power/Other
R3
FERR#/PBE#
Open Drain
Asynchronous
VSS
Power/Other
N2
IGNNE#
CMOS
Asynchronous
N23
VCC
Power/Other
N24
VCC
Power/Other
R30
N25
VCC
Power/Other
R4
A08#
Source Sync
VSS
Power/Other
N26
VCC
Power/Other
R5
N27
VCC
Power/Other
R6
ADSTB0#
Source Sync
VSS
Power/Other
N28
VCC
Power/Other
R7
N29
VCC
Power/Other
R8
VCC
Power/Other
COMP1
Power/Other
N3
VSS
Power/Other
T1
N30
VCC
Power/Other
T2
RESERVED
Source Sync
T23
VCC
Power/Other
Output
Input/Output
Input/Output
Input
N4
A36#
N5
RESERVED
T24
VCC
Power/Other
N6
VSS
Power/Other
T25
VCC
Power/Other
N7
VSS
Power/Other
T26
VCC
Power/Other
T27
VCC
Power/Other
Input
T28
VCC
Power/Other
Input
T29
VCC
Power/Other
T3
VSS
Power/Other
T30
VCC
Power/Other
T4
A11#
Source Sync
Input/Output
T5
A09#
Source Sync
Input/Output
T6
VSS
Power/Other
T7
VSS
Power/Other
T8
VCC
Power/Other
U1
TESTIN2
Power/Other
Input
Input/Output
N8
VCC
Power/Other
P1
TESTHI10
Power/Other
P2
SMI#
CMOS
Asynchronous
P23
VSS
Power/Other
P24
VSS
Power/Other
P25
VSS
Power/Other
P26
VSS
Power/Other
P27
VSS
Power/Other
P28
VSS
Power/Other
P29
VSS
Power/Other
P3
INIT#
CMOS
Asynchronous
P30
VSS
Power/Other
P4
VSS
Power/Other
Input/Output
Input
Input
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
U2
AP0#
Common Clk
U23
VCC
Power/Other
U24
VCC
Power/Other
77
Land Listing
Table 4-2. Land Listing by Land Number
(Sheet 19 of 20)
Pin
No.
Pin Name
Signal
Buffer Type
Table 4-2. Land Listing by Land Number
(Sheet 20 of 20)
Pin
No.
Direction
Pin Name
Signal
Buffer Type
Direction
U25
VCC
Power/Other
W27
VCC
Power/Other
U26
VCC
Power/Other
W28
VCC
Power/Other
U27
VCC
Power/Other
W29
VCC
Power/Other
U28
VCC
Power/Other
W3
TESTHI01
Power/Other
U29
VCC
Power/Other
W30
VCC
Power/Other
U3
AP1#
Common Clk
W4
VSS
Power/Other
U30
VCC
Power/Other
W5
A16#
Source Sync
Input/Output
U4
A13#
Source Sync
Input/Output
W6
A18#
Source Sync
Input/Output
U5
A12#
Source Sync
Input/Output
W7
VSS
Power/Other
Input/Output
W8
VCC
Power/Other
Y1
RESERVED
Input/Output
U6
A10#
Source Sync
U7
VSS
Power/Other
U8
VCC
Power/Other
Y2
VSS
Power/Other
V1
MS_ID1
Power/Other
Output
Y23
VCC
Power/Other
V2
LL_ID0
Power/Other
Output
Y24
VCC
Power/Other
V23
VSS
Power/Other
Y25
VCC
Power/Other
V24
VSS
Power/Other
Y26
VCC
Power/Other
V25
VSS
Power/Other
Y27
VCC
Power/Other
V26
VSS
Power/Other
Y28
VCC
Power/Other
V27
VSS
Power/Other
Y29
VCC
Power/Other
V28
VSS
Power/Other
Y3
RESERVED
V29
VSS
Power/Other
Y30
VCC
Power/Other
V3
VSS
Power/Other
Y4
A20#
Source Sync
V30
VSS
Power/Other
Y5
VSS
Power/Other
V4
A15#
Source Sync
Input/Output
Y6
A19#
Source Sync
V5
A14#
Source Sync
Input/Output
Y7
VSS
Power/Other
V6
VSS
Power/Other
Y8
VCC
Power/Other
V7
VSS
Power/Other
V8
VCC
Power/Other
W1
MS_ID0
Power/Other
Output
W2
TESTIN1
Power/Other
Input
W23
VCC
Power/Other
W24
VCC
Power/Other
W25
VCC
Power/Other
W26
VCC
Power/Other
Input
Input/Output
Input/Output
§
78
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Signal Definitions
5
Signal Definitions
5.1
Signal Definitions
Table 5-1.
Signal Definitions (Sheet 1 of 7)
Name
Description
Notes
I/O
A[37:3]# (Address) define a 2 -byte physical memory address space. In sub-phase
1 of the address phase, these signals transmit the address of a transaction. In subphase 2, these signals transmit transaction type information. These signals must
connect the appropriate pins of all agents on the FSB. A[37:3]#4 are protected by
parity signals AP[1:0]#. A[37:3]#4 are source synchronous signals and are latched
into the receiving buffers by ADSTB[1:0]#.
On the active-to-inactive transition of RESET#, the processors sample a subset of the
A[37:3]#4 lands to determine their power-on configuration. See Section 7.1.
3,4
I
If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit 20
(A20#) before looking up a line in any internal cache and before driving a read/write
transaction on the bus. Asserting A20M# emulates the 8086 processor's address
wrap-around at the 1 MB boundary. Assertion of A20M# is only supported in real
mode.
A20M# is an asynchronous signal. However, to ensure recognition of this signal
following an I/O write instruction, it must be valid along with the TRDY# assertion of
the corresponding I/O write bus transaction.
2
ADS#
I/O
ADS# (Address Strobe) is asserted to indicate the validity of the transaction address
on the A[37:3]#4 lands. All bus agents observe the ADS# activation to begin parity
checking, protocol checking, address decode, internal snoop, or deferred reply ID
match operations associated with the new transaction. This signal must be connected
to the appropriate pins on all Quad-Core Intel® Xeon® Processor 5300 Series FSB
agents.
3
ADSTB[1:0]#
I/O
Address strobes are used to latch A[37:3]#4 and REQ[4:0]# on their rising and falling
edge. Strobes are associated with signals as shown below.
3,4
A[37:3]#
A20M#
AP[1:0]#
Type
I/O
38
Signals
Associated Strobes
REQ[4:0], A[16:3]#,
A[37:36]#4
ADSTB0#
A[35:17]#
ADSTB1#
AP[1:0]# (Address Parity) are driven by the request initiator along with ADS#,
A[37:3]#4, and the transaction type on the REQ[4:0]# signals. A correct parity signal
is high if an even number of covered signals are low and low if an odd number of
covered signals are low. This allows parity to be high when all the covered signals are
high. AP[1:0]# must be connected to the appropriate pins of all Quad-Core Intel®
Xeon® Processor 5300 Series FSB agents. The following table defines the coverage
model of these signals.
Request Signals
Subphase 1
Subphase 2
4
AP0#
AP1#
A[23:3]#
AP1#
AP0#
REQ[4:0]#
AP1#
AP0#
A[37:24]#
BCLK[1:0]
I
The differential bus clock pair BCLK[1:0] (Bus Clock) determines the FSB frequency.
All processor FSB agents must receive these signals to drive their outputs and latch
their inputs.
All external timing parameters are specified with respect to the rising edge of BCLK0
crossing VCROSS.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
3,4
3
79
Signal Definitions
Table 5-1.
Name
Signal Definitions (Sheet 2 of 7)
Type
Description
Notes
BINIT#
I/O
BINIT# (Bus Initialization) may be observed and driven by all processor FSB agents
and if used, must connect the appropriate pins of all such agents. If the BINIT# driver
is enabled during power on configuration, BINIT# is asserted to signal any bus
condition that prevents reliable future operation.
If BINIT# observation is enabled during power-on configuration (see Section 7.1) and
BINIT# is sampled asserted, symmetric agents reset their bus LOCK# activity and
bus request arbitration state machines. The bus agents do not reset their I/O Queue
(IOQ) and transaction tracking state machines upon observation of BINIT# assertion.
Once the BINIT# assertion has been observed, the bus agents will re-arbitrate for the
FSB and attempt completion of their bus queue and IOQ entries.
If BINIT# observation is disabled during power-on configuration, a priority agent may
handle an assertion of BINIT# as appropriate to the error handling architecture of the
system.
3
BNR#
I/O
BNR# (Block Next Request) is used to assert a bus stall by any bus agent who is
unable to accept new bus transactions. During a bus stall, the current bus owner
cannot issue any new transactions.
Since multiple agents might need to request a bus stall at the same time, BNR# is a
wired-OR signal which must connect the appropriate pins of all processor FSB agents.
In order to avoid wired-OR glitches associated with simultaneous edge transitions
driven by multiple drivers, BNR# is activated on specific clock edges and sampled on
specific clock edges.
3
BPM5#
BPM4#
BPM3#
BPM[2:1]#
BPM0#
I/O
BPM[5:0]# (Breakpoint Monitor) are breakpoint and performance monitor signals.
They are outputs from the processor which indicate the status of breakpoints and
programmable counters used for monitoring processor performance. BPM[5:0]#
should connect the appropriate pins of all FSB agents.
BPM4# provides PRDY# (Probe Ready) functionality for the TAP port. PRDY# is a
processor output used by debug tools to determine processor debug readiness.
BPM5# provides PREQ# (Probe Request) functionality for the TAP port. PREQ# is used
by debug tools to request debug operation of the processors.
BPM[5:4]# must be bussed to all bus agents. Please refer to the appropriate platform
design guidelines for more detailed information.
2
BPMb3#
BPMb[2:1]#
BPMb0#
I/O
O
I/O
BPMb[3:0]# (Breakpoint Monitor) are a second set of breakpoint and performance
monitor signals. They are additional outputs from the processor which indicate the
status of breakpoints and programmable counters used for monitoring processor
performance. BPMb[3:0]# should connect the appropriate pins of all FSB agents.
2
I
BPRI# (Bus Priority Request) is used to arbitrate for ownership of the processor FSB.
It must connect the appropriate pins of all processor FSB agents. Observing BPRI#
active (as asserted by the priority agent) causes all other agents to stop issuing new
requests, unless such requests are part of an ongoing locked operation. The priority
agent keeps BPRI# asserted until all of its requests are completed, then releases the
bus by deasserting BPRI#.
3
BR[1:0]#
I/O
The BR[1:0]# signals are sampled on the active-to-inactive transition of RESET#. The
signal which the agent samples asserted determines its agent ID. BR0# drives the
BREQ0# signal in the system and is used by the processor to request the bus.
These signals do not have on-die termination and must be terminated.
3
BSEL[2:0]
O
The BCLK[1:0] frequency select signals BSEL[2:0] are used to select the processor
input clock frequency. Table 2-2 defines the possible combinations of the signals and
the frequency associated with each combination. The required frequency is
determined by the processors, chipset, and clock synthesizer. All FSB agents must
operate at the same frequency. For more information about these signals, including
termination recommendations, refer to the appropriate platform design guideline.
COMP[3:0]
I
COMP[3:0] must be terminated to VSS on the baseboard using precision resistors.
These inputs configure the AGTL+ drivers of the processor. Refer to the appropriate
platform design guidelines for implementation details.
BPRI#
80
O
I/O
O
I/O
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Signal Definitions
Table 5-1.
Name
D[63:0]#
Signal Definitions (Sheet 3 of 7)
Type
Description
Notes
I/O
D[63:0]# (Data) are the data signals. These signals provide a 64-bit data path
between the processor FSB agents, and must connect the appropriate pins on all such
agents. The data driver asserts DRDY# to indicate a valid data transfer.
3
D[63:0]# are quad-pumped signals, and will thus be driven four times in a
common clock period. D[63:0]# are latched off the falling edge of both
DSTBP[3:0]# and DSTBN[3:0]#. Each group of 16 data signals correspond
to a pair of one DSTBP# and one DSTBN#. The following table shows the
grouping of data signals to strobes and DBI#.
Data Group
DSTBN#/
DSTBP#
DBI#
D[15:0]#
0
0
D[31:16]#
1
1
D[47:32]#
2
2
D[63:48]#
3
3
Furthermore, the DBI# signals determine the polarity of the data signals.
Each group of 16 data signals corresponds to one DBI# signal. When the
DBI# signal is active, the corresponding data group is inverted and
therefore sampled active high.
DBI[3:0]#
I/O
DBI[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity of
the D[63:0]# signals. The DBI[3:0]# signals are activated when the data on the data
bus is inverted. If more than half the data bits, within, within a 16-bit group, would
have been asserted electronically low, the bus agent may invert the data bus signals
for that particular sub-phase for that 16-bit group.
3
DBI[3:0] Assignment to Data Bus
Bus Signal
DBR#
Data Bus Signals
DBI0#
D[15:0]#
DBI1#
D[31:16]#
DBI2#
D[47:32]#
DBI3#
D[63:48]#
O
DBR# is used only in systems where no debug port connector is implemented on the
system board. DBR# is used by a debug port interposer so that an in-target probe can
drive reset. If a debug port connector is implemented in the system, DBR# is a noconnect on the Quad-Core Intel® Xeon® Processor 5300 Series package. DBR# is not
a processor signal.
DBSY#
I/O
DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on the
processor FSB to indicate that the data bus is in use. The data bus is released after
DBSY# is deasserted. This signal must connect the appropriate pins on all processor
FSB agents.
3
DEFER#
I
DEFER# is asserted by an agent to indicate that a transaction cannot be guaranteed
in-order completion. Assertion of DEFER# is normally the responsibility of the
addressed memory or I/O agent. This signal must connect the appropriate pins of all
processor FSB agents.
3
DP[3:0]#
I/O
DP[3:0]# (Data Parity) provide parity protection for the D[63:0]# signals. They are
driven by the agent responsible for driving D[63:0]#, and must connect the
appropriate pins of all processor FSB agents.
3
DRDY#
I/O
DRDY# (Data Ready) is asserted by the data driver on each data transfer, indicating
valid data on the data bus. In a multi-common clock data transfer, DRDY# may be
deasserted to insert idle clocks. This signal must connect the appropriate pins of all
processor FSB agents.
3
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
81
Signal Definitions
Table 5-1.
Signal Definitions (Sheet 4 of 7)
Name
DSTBN[3:0]#
DSTBP[3:0]#
Type
I/O
I/O
Description
Data strobe used to latch in D[63:0]#.
Signals
Associated Strobes
D[15:0]#, DBI0#
DSTBN0#
D[31:16]#, DBI1#
DSTBN1#
D[47:32]#, DBI2#
DSTBN2#
D[63:48]#, DBI3#
DSTBN3#
Data strobe used to latch in D[63:0]#.
Signals
Associated Strobes
D[15:0]#, DBI0#
DSTBP0#
D[31:16]#, DBI1#
DSTBP1#
D[47:32]#, DBI2#
DSTBP2#
D[63:48]#, DBI3#
DSTBP3#
Notes
3
3
FERR#/PBE#
O
FERR#/PBE# (floating-point error/pending break event) is a multiplexed signal and
its meaning is qualified by STPCLK#. When STPCLK# is not asserted, FERR#/PBE#
indicates a floating-point error and will be asserted when the processor detects an
unmasked floating-point error. When STPCLK# is not asserted, FERR#/PBE# is similar
to the ERROR# signal on the Intel 387 coprocessor, and is included for compatibility
with systems using MS-DOS*-type floating-point error reporting. When STPCLK# is
asserted, an assertion of FERR#/PBE# indicates that the processor has a pending
break event waiting for service. The assertion of FERR#/PBE# indicates that the
processor should be returned to the Normal state. For additional information on the
pending break event functionality, including the identification of support of the feature
and enable/disable information, refer to Vol. 3 of the Intel® 64 and IA-32 Intel®
Architecture Software Developer’s Manual and the AP-485 Intel® Processor
Identification and the CPUID Instruction application note.
FORCEPR#
I
The FORCEPR# (force power reduction) input can be used by the platform to cause
the Quad-Core Intel® Xeon® Processor 5300 Series to activate the Thermal Control
Circuit (TCC).
GTLREF_ADD_MID
GTLREF_ADD_END
I
GTLREF_ADD determines the signal reference level for AGTL+ address and common
clock input lands. GTLREF_ADD is used by the AGTL+ receivers to determine if a
signal is a logical 0 or a logical 1. Please refer to Table 2-20 and the appropriate
platform design guidelines for additional details.
GTLREF_DATA_MID
GTLREF_DATA_END
I
GTLREF_DATA determines the signal reference level for AGTL+ data input lands.
GTLREF_DATA is used by the AGTL+ receivers to determine if a signal is a logical 0 or
a logical 1. Please refer to Table 2-20 and the appropriate platform design guidelines
for additional details.
HIT#
HITM#
I/O
I/O
HIT# (Snoop Hit) and HITM# (Hit Modified) convey transaction snoop operation
results. Any FSB agent may assert both HIT# and HITM# together to indicate that it
requires a snoop stall, which can be continued by reasserting HIT# and HITM#
together.
3
IERR#
O
IERR# (Internal Error) is asserted by a processor as the result of an internal error.
Assertion of IERR# is usually accompanied by a SHUTDOWN transaction on the
processor FSB. This transaction may optionally be converted to an external error
signal (e.g., NMI) by system core logic. The processor will keep IERR# asserted until
the assertion of RESET#.
This signal does not have on-die termination.
2
82
2
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Signal Definitions
Table 5-1.
Name
Signal Definitions (Sheet 5 of 7)
Type
Description
Notes
IGNNE#
I
IGNNE# (Ignore Numeric Error) is asserted to force the processor to ignore a numeric
error and continue to execute noncontrol floating-point instructions. If IGNNE# is
deasserted, the processor generates an exception on a noncontrol floating-point
instruction if a previous floating-point instruction caused an error. IGNNE# has no
effect when the NE bit in control register 0 (CR0) is set.
IGNNE# is an asynchronous signal. However, to ensure recognition of this signal
following an I/O write instruction, it must be valid along with the TRDY# assertion of
the corresponding I/O write bus transaction.
2
INIT#
I
INIT# (Initialization), when asserted, resets integer registers inside all processors
without affecting their internal caches or floating-point registers. Each processor then
begins execution at the power-on Reset vector configured during power-on
configuration. The processor continues to handle snoop requests during INIT#
assertion. INIT# is an asynchronous signal and must connect the appropriate pins of
all processor FSB agents.
2
LINT[1:0]
I
LINT[1:0] (Local APIC Interrupt) must connect the appropriate pins of all FSB agents.
When the APIC functionality is disabled, the LINT0/INTR signal becomes INTR, a
maskable interrupt request signal, and LINT1/NMI becomes NMI, a nonmaskable
interrupt. INTR and NMI are backward compatible with the signals of those names on
the Pentium® processor. Both signals are asynchronous.
These signals must be software configured via BIOS programming of the APIC register
space to be used either as NMI/INTR or LINT[1:0]. Because the APIC is enabled by
default after Reset, operation of these pins as LINT[1:0] is the default configuration.
2
LL_ID[1:0]
O
The LL_ID[1:0] signals are used to select the correct loadline slope for the processor.
These signals are not connected to the processor die. A logic 0 is pulled to ground and
a logic 1 is a no-connect on the Quad-Core Intel® Xeon® Processor 5300 Series
package.
LOCK#
I/O
LOCK# indicates to the system that a transaction must occur atomically. This signal
must connect the appropriate pins of all processor FSB agents. For a locked sequence
of transactions, LOCK# is asserted from the beginning of the first transaction to the
end of the last transaction.
When the priority agent asserts BPRI# to arbitrate for ownership of the processor
FSB, it will wait until it observes LOCK# deasserted. This enables symmetric agents to
retain ownership of the processor FSB throughout the bus locked operation and
ensure the atomicity of lock.
MCERR#
I/O
MCERR# (Machine Check Error) is asserted to indicate an unrecoverable
error without a bus protocol violation. It may be driven by all processor
FSB agents.
3
MCERR# assertion conditions are configurable at a system level. Assertion
options are defined by the following options:
•
•
•
Enabled or disabled.
Asserted, if configured, for internal errors along with IERR#.
Asserted, if configured, by the request initiator of a bus transaction after it
observes an error.
• Asserted by any bus agent when it observes an error in a bus transaction.
For more details regarding machine check architecture, refer to the Intel® 64 and
IA-32 Intel® Architecture Software Developer’s Manual, Volume 3: System
Programming Guide.
MS_ID[1:0]
PECI
PROCHOT#
O
I/O
O
These signals are provided to indicate the Market Segment for the processor and may
be used for future processor compatibility or for keying. These signals are not
connected to the processor die. A logic 0 is pulled to ground and a logic 1 is a noconnect on the Quad-Core Intel® Xeon® Processor 5300 Series package.
PECI is a proprietary one-wire bus interface that provides a communication channel
between Intel processor and chipset components to external thermal monitoring
devices. See Section 6.4 for more on the PECI interface.
PROCHOT# (Processor Hot) will go active when the processor’s temperature
monitoring sensor detects that the processor has reached its maximum safe operating
temperature. This indicates that the Thermal Control Circuit (TCC) has been
activated, if enabled. The TCC will remain active until shortly after the processor
deasserts PROCHOT#. See Section 6.3.5 for more details.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
83
Signal Definitions
Table 5-1.
Name
Signal Definitions (Sheet 6 of 7)
Type
Description
Notes
PWRGOOD
I
PWRGOOD (Power Good) is an input. The processor requires this signal to be a clean
indication that all processor clocks and power supplies are stable and within their
specifications. “Clean” implies that the signal will remain low (capable of sinking
leakage current), without glitches, from the time that the power supplies are turned
on until they come within specification. The signal must then transition monotonically
to a high state. PWRGOOD can be driven inactive at any time, but clocks and power
must again be stable before a subsequent rising edge of PWRGOOD. It must also
meet the minimum pulse width specification in Table 2-19, and be followed by a 110 ms RESET# pulse.
The PWRGOOD signal must be supplied to the processor; it is used to protect internal
circuits against voltage sequencing issues. It should be driven high throughout
boundary scan operation.
2
REQ[4:0]#
I/O
REQ[4:0]# (Request Command) must connect the appropriate pins of all processor
FSB agents. They are asserted by the current bus owner to define the currently active
transaction type. These signals are source synchronous to ADSTB[1:0]#. Refer to the
AP[1:0]# signal description for details on parity checking of these signals.
3
RESET#
I
Asserting the RESET# signal resets all processors to known states and invalidates
their internal caches without writing back any of their contents. For a power-on Reset,
RESET# must stay active for at least 1 ms after VCC and BCLK have reached their
proper specifications. On observing active RESET#, all FSB agents will deassert their
outputs within two clocks. RESET# must not be kept asserted for more than 10 ms
while PWRGOOD is asserted.
A number of bus signals are sampled at the active-to-inactive transition of RESET#
for power-on configuration. These configuration options are described in the
Section 7.1.
This signal does not have on-die termination and must be terminated on the system
board.
3
RS[2:0]#
I
RS[2:0]# (Response Status) are driven by the response agent (the agent responsible
for completion of the current transaction), and must connect the appropriate pins of
all processor FSB agents.
3
RSP#
I
RSP# (Response Parity) is driven by the response agent (the agent responsible for
completion of the current transaction) during assertion of RS[2:0]#, the signals for
which RSP# provides parity protection. It must connect to the appropriate pins of all
processor FSB agents.
A correct parity signal is high if an even number of covered signals are low and low if
an odd number of covered signals are low. While RS[2:0]# = 000, RSP# is also high,
since this indicates it is not being driven by any agent guaranteeing correct parity.
3
SKTOCC#
O
SKTOCC# (Socket occupied) will be pulled to ground by the processor to indicate that
the processor is present. There is no connection to the processor silicon for this
signal.
SMI#
I
SMI# (System Management Interrupt) is asserted asynchronously by system logic.
On accepting a System Management Interrupt, processors save the current state and
enter System Management Mode (SMM). An SMI Acknowledge transaction is issued,
and the processor begins program execution from the SMM handler.
If SMI# is asserted during the deassertion of RESET# the processor will tri-state its
outputs. See Section 7.1.
2
STPCLK#
I
STPCLK# (Stop Clock), when asserted, causes processors to enter a low power StopGrant state. The processor issues a Stop-Grant Acknowledge transaction, and stops
providing internal clock signals to all processor core units except the FSB and APIC
units. The processor continues to snoop bus transactions and service interrupts while
in Stop-Grant state. When STPCLK# is deasserted, the processor restarts its internal
clock to all units and resumes execution. The assertion of STPCLK# has no effect on
the bus clock; STPCLK# is an asynchronous input.
2
TCK
I
TCK (Test Clock) provides the clock input for the processor Test Bus (also known as
the Test Access Port).
TDI
I
TDI (Test Data In) transfers serial test data into the processor. TDI provides the serial
input needed for JTAG specification support.
TDO
O
TDO (Test Data Out) transfers serial test data out of the processor. TDO provides the
serial output needed for JTAG specification support.
TESTHI[11:0],
I
The TESTHI signals must use individual pull-up resistors. A matched resistor must be
used for each Signal.
84
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Signal Definitions
Table 5-1.
Signal Definitions (Sheet 7 of 7)
Name
TESTIN1
TESTIN2
THERMTRIP#
Type
I
I
Description
Notes
Connect the TESTIN1 and TESTIN2 signals together, then terminate the net with a 51
Ω resistor to VTT.
O
Assertion of THERMTRIP# (Thermal Trip) indicates the processor junction
temperature has reached a temperature beyond which permanent silicon damage
may occur. Measurement of the temperature is accomplished through an internal
thermal sensor. Upon assertion of THERMTRIP#, the processor will shut off its internal
clocks (thus halting program execution) in an attempt to reduce the processor
junction temperature. To protect the processor its core voltage (VCC) must be
removed following the assertion of THERMTRIP#. Intel also recommends the removal
of VTT when THERMTRIP# is asserted.
Driving of the THERMTRIP# signals is enabled within 10 μs of the assertion of
PWRGOOD and is disabled on de-assertion of PWRGOOD. Once activated,
THERMTRIP# remains latched until PWRGOOD is de-asserted. While the de-assertion
of the PWRGOOD signal will de-assert THERMTRIP#, if the processor’s junction
temperature remains at or above the trip level, THERMTRIP# will again be asserted
within 10 μs of the assertion of PWRGOOD.
TMS
I
TMS (Test Mode Select) is a JTAG specification support signal used by debug tools.
TRDY#
I
TRDY# (Target Ready) is asserted by the target to indicate that it is ready to receive a
write or implicit writeback data transfer. TRDY# must connect the appropriate pins of
all FSB agents.
TRST#
I
TRST# (Test Reset) resets the Test Access Port (TAP) logic. TRST# must be driven low
during power on Reset.
VCCPLL
I
The Quad-Core Intel® Xeon® Processor 5300 Series implement an on-die PLL filter
solution. The VCCPLL input is used as a PLL supply voltage.
VCC_DIE_SENSE
VCC_DIE_SENSE2
O
VCC_DIE_SENSE and VCC_DIE_SENSE2 provides an isolated, low impedance
connection to the processor core power and ground. This signal should be connected
to the voltage regulator feedback signal, which insures the output voltage (that is,
processor voltage) remains within specification. Please see the applicable platform
design guide for implementation details.
VID[6:1]
O
VID[6:1] (Voltage ID) pins are used to support automatic selection of power supply
voltages (VCC). These are CMOS signals that are driven by the processor and must be
pulled up through a resistor. Conversely, the voltage regulator output must be
disabled prior to the voltage supply for these pins becomes invalid. The VID pins are
needed to support processor voltage specification variations. See Table 2-3 for
definitions of these pins. The VR must supply the voltage that is requested by these
pins, or disable itself.
VID_SELECT
O
VID_SELECT is an output from the processor which selects the appropriate VID table
for the Voltage Regulator. This signal is not connected to the processor die. This signal
is a no-connect on the Quad-Core Intel® Xeon® Processor 5300 Series package.
VSS_DIE_SENSE
VSS_DIE_SENSE2
O
VSS_DIE_SENSE and VSS_DIE_SENSE2 provides an isolated, low impedance
connection to the processor core power and ground. This signal should be connected
to the voltage regulator feedback signal, which insures the output voltage (that is,
processor voltage) remains within specification. Please see the applicable platform
design guide for implementation details.
VTT
P
The FSB termination voltage input pins. Refer to Table 2-12 for further details.
VTT_OUT
O
The VTT_OUT signals are included in order to provide a local VTT for some signals that
require termination to VTT on the motherboard.
VTT_SEL
O
The VTT_SEL signal is used to select the correct VTT voltage level for the processor.
VTT_SEL is a no-connect on the Quad-Core Intel® Xeon® Processor 5300 Series
package.
1
Notes:
1.
For this processor land on the Quad-Core Intel® Xeon® Processor 5300 Series, the maximum number of symmetric agents is
one. Maximum number of priority agents is zero.
2.
For this processor land on the Quad-Core Intel® Xeon® Processor 5300 Series, the maximum number of symmetric agents is
two. Maximum number of priority agents is zero.
3.
For this processor land on the Quad-Core Intel® Xeon® Processor 5300 Series, the maximum number of symmetric agents is
two. Maximum number of priority agents is one.
4.
Not all Quad-Core Intel® Xeon® Processor 5300 Series support signals A[37:36]#. Processors that support these signals will
be outlined in the Quad-Core Intel® Xeon® Processor 5300 Series NDA Specification Update.
§
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
85
Signal Definitions
86
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
6
Thermal Specifications
6.1
Package Thermal Specifications
The Quad-Core Intel® Xeon® Processor 5300 Series requires a thermal solution to
maintain temperatures within its operating limits. Any attempt to operate the processor
outside these operating limits may result in permanent damage to the processor and
potentially other components within the system. As processor technology changes,
thermal management becomes increasingly crucial when building computer systems.
Maintaining the proper thermal environment is key to reliable, long-term system
operation.
A complete solution includes both component and system level thermal management
features. Component level thermal solutions can include active or passive heatsinks
attached to the processor integrated heat spreader (IHS). Typical system level thermal
solutions may consist of system fans combined with ducting and venting.
This section provides data necessary for developing a complete thermal solution. For
more information on designing a component level thermal solution, refer to the QuadCore Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines and
the Quad-Core Intel® Xeon® Processor LV5318 in Embedded Applications Thermal/
Mechanical Design Guidelines.
Note:
The boxed processor will ship with a component thermal solution. Refer to Section 8 for
details on the boxed processor.
6.1.1
Thermal Specifications
To allow the optimal operation and long-term reliability of Intel processor-based
systems, the processor must remain within the minimum and maximum case
temperature (TCASE) specifications as defined by the applicable thermal profile.
Thermal solutions not designed to provide this level of thermal capability may affect the
long-term reliability of the processor and system. For more details on thermal/
mechanical design guidelines.
The Quad-Core Intel® Xeon® Processor 5300 Series implement a methodology for
managing processor temperatures which is intended to support acoustic noise
reduction through fan speed control and to assure processor reliability. Selection of the
appropriate fan speed is based on the relative temperature data reported by the
processor’s Platform Environment Control Interface (PECI) bus as described in
Section 6.4. The temperature reported over PECI is always a negative value and
represents a delta below the onset of thermal control circuit (TCC) activation, as
indicated by PROCHOT# (see Section 6.3, Processor Thermal Features). Systems that
implement fan speed control must be designed to use this data. Systems that do not
alter the fan speed only need to guarantee the case temperature meets the thermal
profile specifications.
The Quad-Core Intel® Xeon® Processor E5300 (see Figure 6-1; Table 6-2), QuadCore Intel® Xeon® Processor L5300 Series (see Figure 6-4; Table 6-9), and Quad-Core
Intel® Xeon® Processor X5365 Series (see Figure 6-3; Table 6-7) support a single
Thermal Profile. For these processors, it is expected that the Thermal Control Circuit
(TCC) would only be activated for very brief periods of time when running the most
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
87
Thermal Specifications
power-intensive applications. Refer to the Quad-Core Intel® Xeon® Processor 5300
Series Thermal/Mechanical Design Guidelinesfor details on system thermal solution
design, thermal profiles and environmental considerations.
For the Quad-Core Intel® Xeon® Processor X5300 Series, Intel has developed two
thermal profiles, either of which can be implemented. Both ensure adherence to Intel
reliability requirements. Thermal Profile A (see Figure 6-2; Table 6-4) is representative
of a volumetrically unconstrained thermal solution (that is, industry enabled 2U
heatsink). In this scenario, it is expected that the Thermal Control Circuit (TCC) would
only be activated for very brief periods of time when running the most power intensive
applications. Thermal Profile B (see Figure 6-2; Table 6-5) is indicative of a constrained
thermal environment (that is, 1U form factor). Because of the reduced cooling
capability represented by this thermal solution, the probability of TCC activation and
performance loss is increased. Additionally, utilization of a thermal solution that does
not meet Thermal Profile B will violate the thermal specifications and may result in
permanent damage to the processor. Refer to the Quad-Core Intel® Xeon® Processor
5300 Series Thermal/Mechanical Design Guidelines for details on system thermal
solution design, thermal profiles and environmental considerations.
The upper point of the thermal profile consists of the Thermal Design Power (TDP) and
the associated TCASE value. It should be noted that the upper point associated with the
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile B (x = TDP and y =
TCASE_MAX_B @ TDP) represents a thermal solution design point. In actuality the
processor case temperature will not reach this value due to TCC activation (see
Figure 6-2 for Quad-Core Intel® Xeon® Processor X5300 Series). The lower point of
the thermal profile consists of x = P_PROFILE_MIN and y = TCASE_MAX @ P_PROFILE_MIN.
P_PROFILE_MIN is defined as the processor power at which TCASE, calculated from the
thermal profile, is equal to 50°C.
Analysis indicates that real applications are unlikely to cause the processor to consume
maximum power dissipation for sustained time periods. Intel recommends that
complete thermal solution designs target the Thermal Design Power (TDP), instead of
the maximum processor power consumption. The Thermal Monitor feature is intended
to help protect the processor in the event that an application exceeds the TDP
recommendation for a sustained time period. For more details on this feature, refer to
Section 6.3. To ensure maximum flexibility for future requirements, systems should be
designed to the Flexible Motherboard (FMB) guidelines, even if a processor with lower
power dissipation is currently planned. Thermal Monitor 1 and Thermal Monitor 2
feature must be enabled for the processor to remain within its specifications.
Intel has developed thermal profiles specific to enable the Dual-Core Intel® Xeon®
Processor LV 5318, to be used in environments compliant with NEBS* Level 3 ambient
operating temperature requirements. At a minimum, NEBS Level 3 requires a nominal
ambient operating temperature of 40°C, with short-term excursions to 55°C. “Shortterm” is defined as a maximum of 96 hours per instance, for a total maximum of 360
hours per year, and a maximum of 15 instances per year.
To comply with these ambient operating temperature requirements, Intel has
developed a corresponding Nominal Thermal Profile and Short-Term Thermal Profile.
For normal operation, the processor must remain within the minimum and maximum
case temperature (TCASE) specifications as defined by the Nominal Thermal Profile. For
short-term operating conditions (maximum 96 hours per instance, maximum 360 hours
per year, maximum of 15 instances per year), the processor may remain within the
minimum and maximum TCASE, as defined by the Short-Term Thermal Profile. For
environments that do not require NEBS Level 3 compliance, the processor must always
remain within the minimum and maximum case temperature (TCASE) specifications as
defined by the Nominal Thermal Profile.
88
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
To provide greater flexibility in environmental conditions and thermal solution design,
the Nominal Thermal Profile and the Short-Term Thermal Profile are each specified 5°C
above the NEBS Level 3 ambient operating temperature requirements of 40°C nominal
and 55°C short-term. The Nominal Thermal Profile is defined at an ambient operating
temperature of 45°C, and the Short-Term Thermal Profile is defined at an ambient
operating temperature of 60°C.
Both of these thermal profiles ensure adherence to Intel reliability requirements. It is
expected that the Thermal Control Circuit (TCC) would only be activated for very brief
periods of time when running the most power intensive applications. Utilization of a
thermal solution that exceeds the Short-Term Thermal Profile, or which operates at the
Short-Term Thermal Profile for a duration longer than the specified limits will violate the
thermal specifications and may result in permanent damage to the processor. Refer to
the Quad-Core Intel® Xeon® Processor LV 5318 in Embedded Applications Thermal/
Mechanical Design Guidelines for details on system thermal solution design, thermal
profiles and environmental considerations.
Table 6-1.
Quad-Core Intel® Xeon® Processor E5300 Series Thermal Specifications
Core
Frequency
Launch to FMB
Maximum
Power
(W)
Thermal
Design Power
(W)
Minimum
TCASE
(°C)
Maximum
TCASE
(°C)
100
80
5
See Figure 6-1;
Table 6-2
Notes
1, 2, 3, 4, 5, 6
Notes:
1.
These values are specified at VCC_MAX for all processor frequencies. Systems must be designed to ensure
the processor is not to be subjected to any static VCC and ICC combination wherein VCC exceeds VCC_MAX at
specified ICC. Please refer to the loadline specifications in Section 2.
2.
Maximum Power is the highest power the processor will dissipate, regardless of its VID. Maximum Power is
measured at maximum TCASE.
3.
Thermal Design Power (TDP) should be used for processor thermal solution design targets. TDP is not the
maximum power that the processor can dissipate. TDP is measured at maximum TCASE.
4.
These specifications are based on silicon characterization.
5.
Power specifications are defined at all VIDs found in Table 2-3. The Quad-Core Intel® Xeon® Processor
E5300 may be shipped under multiple VIDs for each frequency.
6.
FMB, or Flexible Motherboard, guidelines provide a design target for meeting all planned processor
frequency requirements.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
89
Thermal Specifications
Figure 6-1.Quad-Core Intel® Xeon® Processor E5300 Series Thermal Profile
70
65
Thermal Profile
Y = 0.293*x + 42.6
Tcase [C]
60
55
50
45
40
0
10
20
30
40
50
60
70
80
Power [W]
Notes:
1.
Please refer to Table 6-2 for discrete points that constitute the thermal profile.
2.
Refer to the Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for
system and environmental implementation details.
Table 6-2.
Quad-Core Intel® Xeon® Processor E5300 Series Thermal Profile Table
Power (W)
90
TCASE_MAX (° C)
P_PROFILE_MIN=25.3
50.0
30
51.4
35
52.9
40
54.3
45
55.8
50
57.3
55
58.7
60
60.2
65
61.6
70
63.1
75
64.6
80
66.0
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
Table 6-3.
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Specifications
Core
Frequency
Launch to FMB
Maximum
Power
(W)
Thermal
Design Power
(W)
Minimum
TCASE
(°C)
Maximum
TCASE
(°C)
145
120
5
See Figure 6-2;
Table 6-4;
Table 6-5
Notes
1, 2, 3, 4, 5, 6
Notes:
1.
These values are specified at VCC_MAX for all processor frequencies. Systems must be designed to ensure
the processor is not to be subjected to any static VCC and ICC combination wherein VCC exceeds VCC_MAX at
specified ICC. Please refer to the loadline specifications in Section 2.
2.
Maximum Power is the highest power the processor will dissipate, regardless of its VID. Maximum Power is
measured at maximum TCASE.
3.
Thermal Design Power (TDP) should be used for processor thermal solution design targets. TDP is not the
maximum power that the processor can dissipate. TDP is measured at maximum TCASE.
4.
These specifications are based on silicon characterization.
5.
Power specifications are defined at all VIDs found in Table 2-3. The Quad-Core Intel® Xeon® Processor
X5300 Series may be shipped under multiple VIDs for each frequency.
6.
FMB, or Flexible Motherboard, guidelines provide a design target for meeting all planned processor
frequency requirements.
Figure 6-2.Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profiles
TCASE_MAX is a thermal solution design point.
In actuality, units will not significantly exceed
TCASE_MAX_A due to TCC activation.
75
70
Tcase [C]
65
60
Thermal Profile B
Y = 0.224*x + 43.1
55
Thermal Profile A
Y = 0.171*x + 42.5
50
45
40
0
10
20
30
40
50
60
70
80
90
100
110
120
Pow e r [W]
Notes:
1.
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile A is representative of a volumetrically
unconstrained platform. Please refer to Table 6-4 for discrete points that constitute the thermal profile.
2.
Implementation of Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile A should result in
virtually no TCC activation. Furthermore, utilization of thermal solutions that do not meet processor QuadCore Intel® Xeon® Processor X5300 Series Thermal Profile A will result in increased probability of TCC
activation and may incur measurable performance loss. (See Section 6.3 for details on TCC activation).
3.
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile B is representative of a volumetrically
constrained platform. Please refer to Table 6-5 for discrete points that constitute the thermal profile.
4.
Implementation of Thermal Profile B will result in increased probability of TCC activation and measurable
performance loss. Furthermore, utilization of thermal solutions that do not meet Thermal Profile B do not
meet the processor's thermal specifications and may result in permanent damage to the processor.
5.
Refer to the Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for
system and environmental implementation details.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
91
Thermal Specifications
Table 6-4.
Table 6-5.
92
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile A Table
Power (W)
TCASE_MAX (° C)
P_PROFILE_MIN_A=43.9
50.0
45
50.2
50
51.1
55
51.9
60
52.8
65
53.6
70
54.5
75
55.3
80
56.2
85
57.0
90
57.9
95
58.7
100
59.6
105
60.5
110
61.3
115
62.2
120
63.0
Quad-Core Intel® Xeon® Processor X5300 Series Thermal Profile B Table
Power (W)
TCASE_MAX (° C)
P_PROFILE_MIN_B=30.8
50.0
35
50.9
40
52.1
45
53.2
50
54.3
55
55.4
60
56.5
65
57.7
70
58.8
75
59.9
80
61.0
85
62.1
90
63.3
95
64.4
100
65.5
105
66.6
110
67.7
115
68.9
120
70.0
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
Table 6-6.
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Specifications
Core
Frequency
Launch to FMB
Maximum
Power
(W)
Thermal
Design Power
(W)
Minimum
TCASE
(°C)
Maximum
TCASE
(°C)
180
150
5
See Figure 6-3;
Table 6-7
Notes
1, 2, 3, 4, 5, 6
Notes:
1.
These values are specified at VCC_MAX for all processor frequencies. Systems must be designed to ensure
the processor is not to be subjected to any static VCC and ICC combination wherein VCC exceeds VCC_MAX at
specified ICC. Please refer to the loadline specifications in Section 2.
2.
Maximum Power is the highest power the processor will dissipate, regardless of its VID. Maximum Power is
measured at maximum TCASE.
3.
Thermal Design Power (TDP) should be used for processor thermal solution design targets. TDP is not the
maximum power that the processor can dissipate. TDP is measured at maximum TCASE.
4.
These specifications are based on silicon characterization.
5.
Power specifications are defined at all VIDs found in Table 2-3. The Quad-Core Intel® Xeon® Processor
L5300 Series may be shipped under multiple VIDs for each frequency.
6.
FMB, or Flexible Motherboard, guidelines provide a design target for meeting all planned processor
frequency requirements.
7.
8.
Figure 6-3.
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Profile
65
60
Thermal Profile
Y = 0.187*x + 35.0
Tcase [C]
55
50
45
40
35
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
Pow e r [W]
Notes:
1.
Please refer to Table 6-7 for discrete points that constitute the thermal profile.
2.
Refer to the Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for
system and environmental implementation details.
3.
4.
5.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
93
Thermal Specifications
Table 6-7.
Table 6-8.
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Profile (Sheet 1 of
2)
Power (W)
TCASE_MAX (° C)
P_PROFILE_MIN=50
44.3
55
45.3
60
46.2
65
47.1
70
48.1
75
49.0
80
49.9
85
50.9
90
51.8
95
52.7
100
53.7
105
54.6
110
55.5
115
56.5
120
57.4
125
58.3
130
59.3
135
60.2
140
61.1
145
62.1
150
63.0
Quad-Core Intel® Xeon® Processor L5300 Series Thermal Specifications
Core
Frequency
Launch to FMB
Maximum Power
(W)
Thermal Design
Power
(W)
Minimum
TCASE
(°C)
Maximum
TCASE
(°C)
65
50
5
See Figure 6-4;
Table 6-9
Notes
1, 2, 3, 4, 5, 6
Notes:
1.
These values are specified at VCC_MAX for all processor frequencies. Systems must be designed to ensure
the processor is not to be subjected to any static VCC and ICC combination wherein VCC exceeds VCC_MAX at
specified ICC. Please refer to the loadline specifications in Section 2.
2.
Maximum Power is the highest power the processor will dissipate, regardless of its VID. Maximum Power is
measured at maximum TCASE.
3.
Thermal Design Power (TDP) should be used for processor thermal solution design targets. TDP is not the
maximum power that the processor can dissipate. TDP is measured at maximum TCASE.
4.
These specifications are based on silicon characterization.
5.
Power specifications are defined at all VIDs found in Table 2-3. The Quad-Core Intel® Xeon® Processor
L5300 Series may be shipped under multiple VIDs for each frequency.
6.
FMB, or Flexible Motherboard, guidelines provide a design target for meeting all planned processor
frequency requirements.
94
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
Figure 6-4.
Quad-Core Intel® Xeon® Processor L5300 Series Thermal Profile
65
60
Thermal Profile
55
Tcase [C]
Y = 0.360*x + 42.0
50
45
40
0
10
20
30
40
50
Pow er [W]
Notes:
1.
Please refer to Table 6-9 for discrete points that constitute the thermal profile.
2.
Refer to the Quad-Core Intel® Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for
system and environmental implementation details.
6.2
Table 6-9. Quad-Core Intel® Xeon® Processor L5300 Series Thermal Profile
Power (W)
TCASE_MAX (° C)
P_PROFILE_MIN=22.2
50.0
25
51.0
30
52.8
35
54.6
40
56.4
45
58.2
50
60.0
Table 6-10.Quad-Core Intel® Xeon® Processor L5318 Thermal Specifications
Core
Frequency
Launch to FMB
Maximum
Power
(W)
Thermal
Design Power
(W)
Minimum
TCASE
(°C)
Maximum
TCASE
(°C)
50
40
5
See Figure 6-5;
Table 6-11 and
Table 6-12
Notes
1, 2, 3, 4, 5, 6
Notes:
1.
These values are specified at VCC_MAX for all processor frequencies. Systems must be designed to ensure
the processor is not to be subjected to any static VCC and ICC combination wherein VCC exceeds VCC_MAX at
specified ICC. Please refer to the loadline specifications in Section 2.
2.
Maximum Power is the highest power the processor will dissipate, regardless of its VID. Maximum Power is
measured at maximum TCASE.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
95
Thermal Specifications
3.
4.
5.
6.
Figure 6-5.
Thermal Design Power (TDP) should be used for processor thermal solution design targets. TDP is not the
maximum power that the processor can dissipate. TDP is measured at maximum TCASE.
These specifications are based on silicon characterization.
Power specifications are defined at all VIDs found in Table 2-3. The Quad-Core Intel® Xeon® Processor
L5300 Series may be shipped under multiple VIDs for each frequency.
FMB, or Flexible Motherboard, guidelines provide a design target for meeting all planned processor
frequency requirements.
Quad-Core Intel® Xeon® Processor L5318 Thermal Profile
Notes:
1.
Please refer to Table 6-11 and Table 6-12 for discrete points that constitute the thermal profile.
2.
Refer to the Quad-Core Intel® Xeon® Processor L5318 Thermal/Mechanical Design Guidelines for system
and environmental implementation details.
3.
The Nominal Thermal Profile must be used for all normal operating conditions, or for products that do not
require NEBS Level 3 compliance.
4.
The Short-Term Thermal Profile may only be used for short-term excursions to higher ambient operating
temperatures, not to exceed 96 hours per instance, 360 hours per year, and a maximum of 15 instances
per year, as compliant with NEBS Level 3.
5.
Implementation of either thermal profile should result in virtually no TCC activation.
6.
Utilization of a thermal solution that exceeds the Short-Term Thermal Profile, or which operates at the
Short-Term Thermal Profile for a duration longer than the limits specified in Note 3 above, do not meet the
processor’s thermal specifications and may result in permanent damage to the processor.
96
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
Table 6-11. Quad-Core Intel® Xeon® Processor L5318 Nominal Thermal Profile
Power (W)
TCASE_MAX (° C)
P_PROFILE_MIN=0
45.0
5
48.4
10
51.8
15
55.2
20
58.6
25
62.0
30
65.4
35
68.8
40
72.2
Table 6-12. Quad-Core Intel® Xeon® Processor L5318 Short Term Thermal Profile
Power (W)
6.2.1
TCASE_MAX (° C)
P_PROFILE_MIN=0
60.0
5
63.4
10
66.8
15
70.2
20
73.6
25
77.0
30
80.4
35
83.8
40
87.2
Thermal Metrology
The minimum and maximum case temperatures (TCASE) are specified in Table 6-1,
through Table 6-7 and are measured at the geometric top center of the processor
integrated heat spreader (IHS). Figure 6-6 illustrates the location where TCASE
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
97
Thermal Specifications
temperature measurements should be made. For detailed guidelines on temperature
measurement methodology, refer to the Quad-Core Intel® Xeon® Processor 5300
Series Thermal/Mechanical Design Guidelines
Figure 6-6.
Case Temperature (TCASE) Measurement Location
Note:
Figure is not to scale and is for reference only.
6.3
Processor Thermal Features
6.3.1
Thermal Monitor Features
Quad-Core Intel® Xeon® Processor 5300 Series provide two thermal monitor features,
Thermal Monitor (TM1) and Enhanced Thermal Monitor (TM2). The TM1 and TM2 must
both be enabled in BIOS for the processor to be operating within specifications. When
both are enabled, TM2 will be activated first and TM1 will be added if TM2 is not
effective.
6.3.2
Thermal Monitor (TM1)
The Thermal Monitor (TM1) feature helps control the processor temperature by
activating the Thermal Control Circuit (TCC) when the processor silicon reaches its
maximum operating temperature. The TCC reduces processor power consumption as
needed by modulating (starting and stopping) the internal processor core clocks. The
temperature at which Thermal Monitor activates the thermal control circuit is not user
98
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
configurable and is not software visible. Bus traffic is snooped in the normal manner,
and interrupt requests are latched (and serviced during the time that the clocks are on)
while the TCC is active.
When the TM1 is enabled, and a high temperature situation exists (that is, TCC is
active), the clocks will be modulated by alternately turning off and on at a duty cycle
specific to the processor (typically 30 - 50%). Cycle times are processor speed
dependent and will decrease as processor core frequencies increase. A small amount of
hysteresis has been included to prevent rapid active/inactive transitions of the TCC
when the processor temperature is near its maximum operating temperature. Once the
temperature has dropped below the maximum operating temperature, and the
hysteresis timer has expired, the TCC goes inactive and clock modulation ceases.
With thermal solutions designed to the Quad-Core Intel® Xeon® Processor E5300
Thermal Profile, the Quad-Core Intel® Xeon® Processor L5300 Series Thermal Profile,
Quad-Core Intel® Xeon® Processor X5365 Series Thermal Profile, or Quad-Core
Intel® Xeon® Processor X5300 Series Thermal Profile A it is anticipated that the TCC
would only be activated for very short periods of time when running the most power
intensive applications. The processor performance impact due to these brief periods of
TCC activation is expected to be so minor that it would be immeasurable. A thermal
solution that is designed to Quad-Core Intel® Xeon® Processor X5300 Series Thermal
Profile B may cause a noticeable performance loss due to increased TCC activation.
Thermal Solutions that exceed Thermal Profile B will exceed the maximum temperature
specification and affect the long-term reliability of the processor. In addition, a thermal
solution that is significantly under designed may not be capable of cooling the
processor even when the TCC is active continuously Refer to the Quad-Core Intel®
Xeon® Processor 5300 Series Thermal/Mechanical Design Guidelines for information on
designing a thermal solution.
The duty cycle for the TCC, when activated by the TM1, is factory configured and
cannot be modified. The TM1 does not require any additional hardware, software
drivers, or interrupt handling routines.
6.3.3
Thermal Monitor 2
The Quad-Core Intel® Xeon® Processor 5300 Series adds support for an Enhanced
Thermal Monitor capability known as Thermal Monitor 2 (TM2). This mechanism
provides an efficient means for limiting the processor temperature by reducing the
power consumption within the processor. TM2 requires support for dynamic VID
transitions in the platform.
When TM2 is enabled, and a high temperature situation is detected, the Thermal
Control Circuit (TCC) will be activated for all processor cores. The TCC causes the
processor to adjust its operating frequency (via the bus multiplier) and input voltage
(via the VID signals). This combination of reduced frequency and VID results in a
reduction to the processor power consumption.
A processor enabled for TM2 includes two operating points, each consisting of a specific
operating frequency and voltage, which is identical for both processor dies. The first
operating point represents the normal operating condition for the processor. Under this
condition, the core-frequency-to-system-bus multiplier utilized by the processor is that
contained in the CLOCK_FLEX_MAX MSR and the VID that is specified in Table 2-3.
The second operating point consists of both a lower operating frequency and voltage.
The lowest operating frequency is determined by the lowest supported bus ratio (1/6
for the Quad-Core Intel® Xeon® Processor 5300 Series). When the TCC is activated,
the processor automatically transitions to the new frequency. This transition occurs
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
99
Thermal Specifications
rapidly, on the order of 5 µs. During the frequency transition, the processor is unable to
service any bus requests, and consequently, all bus traffic is blocked. Edge-triggered
interrupts will be latched and kept pending until the processor resumes operation at the
new frequency.
Once the new operating frequency is engaged, the processor will transition to the new
core operating voltage by issuing a new VID code to the voltage regulator. The voltage
regulator must support dynamic VID steps in order to support Thermal Monitor 2.
During the voltage change, it will be necessary to transition through multiple VID codes
to reach the target operating voltage. Each step will be one VID table entry (see
Table 2-3). The processor continues to execute instructions during the voltage
transition. Operation at the lower voltage reduces the power consumption of the
processor.
A small amount of hysteresis has been included to prevent rapid active/inactive
transitions of the TCC when the processor temperature is near its maximum operating
temperature. Once the temperature has dropped below the maximum operating
temperature, and the hysteresis timer has expired, the operating frequency and
voltage transition back to the normal system operating point. Transition of the VID code
will occur first, in order to insure proper operation once the processor reaches its
normal operating frequency. Refer to Figure 6-7 for an illustration of this ordering.
Figure 6-7.
Thermal Monitor 2 Frequency and Voltage Ordering
TTM2
Temperature
fMAX
fTM2
Frequency
VNOM
VTM2
Vcc
Time
T(hysterisis)
The PROCHOT# signal is asserted when a high temperature situation is detected,
regardless of whether TM1 or TM2 is enabled.
6.3.4
On-Demand Mode
The processor provides an auxiliary mechanism that allows system software to force
the processor to reduce its power consumption. This mechanism is referred to as “OnDemand” mode and is distinct from the Thermal Monitor 1 and Thermal Monitor 2
features. On-Demand mode is intended as a means to reduce system level power
consumption. Systems utilizing the Quad-Core Intel® Xeon® Processor 5300 Series
must not rely on software usage of this mechanism to limit the processor temperature.
If bit 4 of the IA32_CLOCK_MODULATION MSR is set to a ‘1’, the processor will
immediately reduce its power consumption via modulation (starting and stopping) of
the internal core clock, independent of the processor temperature. When using OnDemand mode, the duty cycle of the clock modulation is programmable via bits 3:1 of
100
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
the same IA32_CLOCK_MODULATION MSR. In On-Demand mode, the duty cycle can
be programmed from 12.5% on/ 87.5% off to 87.5% on/12.5% off in 12.5%
increments. On-Demand mode may be used in conjunction with the Thermal Monitor;
however, if the system tries to enable On-Demand mode at the same time the TCC is
engaged, the factory configured duty cycle of the TCC will override the duty cycle
selected by the On-Demand mode.
6.3.5
PROCHOT# Signal
An external signal, PROCHOT# (processor hot) is asserted when the processor die
temperature of any processor cores has reached its factory configured trip point. If
Thermal Monitor is enabled (note that Thermal Monitor must be enabled for the
processor to be operating within specification), the TCC will be active when PROCHOT#
is asserted. The processor can be configured to generate an interrupt upon the
assertion or de-assertion of PROCHOT#. Refer to the Intel® 64 and IA-32 Architectures
Software Developer’s Manual and the Conroe and Woodcrest Processor Family BIOS
Writer’s Guide for specific register and programming details.
PROCHOT# is designed to assert at or a few degrees higher than maximum TCASE (as
specified by Thermal Profile A) when dissipating TDP power, and cannot be interpreted
as an indication of processor case temperature. This temperature delta accounts for
processor package, lifetime and manufacturing variations and attempts to ensure the
Thermal Control Circuit is not activated below maximum TCASE when dissipating TDP
power. There is no defined or fixed correlation between the PROCHOT# trip
temperature, or the case temperature. Thermal solutions must be designed to the
processor specifications and cannot be adjusted based on experimental measurements
of TCASE, or PROCHOT#.
6.3.6
FORCEPR# Signal
The FORCEPR# (force power reduction) input can be used by the platform to cause the
Quad-Core Intel® Xeon® Processor 5300 Series to activate the TCC. If the processor
supports Thermal Monitor 2 (TM2), and has Thermal Monitor 2 and Thermal Monitor
(TM) properly enabled, assertion of the FORCEPR# signal will immediately activate
Thermal Monitor 2. If the processor does not support Thermal Monitor 2, but has
Thermal Monitor properly enabled, FORCEPR# signal assertion will cause Thermal
Monitor to become active. Please refer to the Quad-Core Intel® Xeon® Processor 5300
Series NDA Specification Update to determine which processors support TM2 and
Conroe and Woodcrest Processor Family BIOS Writer’s Guide for details on enabling
these capabilities. Assertion of the FORCEPR# signal will activate TCC for all processor
cores. The TCC will remain active until the system deasserts FORCEPR#.
FORCEPR# is an asynchronous input, which can be employed to thermally protect other
system components. To use the voltage regulator (VR) as an example, TCC circuit
activation will reduce the current consumption of the processor and the corresponding
temperature of the VR.
It should be noted that assertion of FORCEPR# does not automatically assert
PROCHOT#. As mentioned previously, the PROCHOT# signal is asserted when a high
temperature situation is detected. A minimum pulse width of 500 µs is recommended
when FORCEPR# is asserted by the system. Sustained activation of the FORCEPR#
signal may cause noticeable platform performance degradation.
Refer to the appropriate platform design guidelines for details on implementing the
FORCEPR# signal feature.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
101
Thermal Specifications
6.3.7
THERMTRIP# Signal
Regardless of whether or not TM1 or TM2 is enabled, in the event of a catastrophic
cooling failure, the processor will automatically shut down when the silicon has reached
an elevated temperature (refer to the THERMTRIP# definition in Table 5-1). At this
point, the FSB signal THERMTRIP# will go active and stay active as described in
Table 5-1. THERMTRIP# activation is independent of processor activity and does not
generate any bus cycles. Intel also recommends the removal of VTT.
6.4
Platform Environment Control Interface (PECI)
6.4.1
Introduction
PECI offers an interface for thermal monitoring of Intel processor and chipset
components. It uses a single wire, thus alleviating routing congestion issues.
Figure 6-8 shows an example of the PECI topology in a system with Quad-Core Intel®
Xeon® Processor 5300 Series. PECI uses CRC checking on the host side to ensure
reliable transfers between the host and client devices. Also, data transfer speeds across
the PECI interface are negotiable within a wide range (2 Kbps to 2 Mbps). The PECI
interface on Quad-Core Intel® Xeon® Processor 5300 Series is disabled by default and
must be enabled through BIOS. More information on this can be found in the Conroe
and Woodcrest Processor Family BIOS Writer’s Guide.
Figure 6-8.
PECI Topology
Q u a d -C o re In te l® X e o n ®
P ro c e s s o r 5 3 0 0 S e rie s
(S o c k e t 0 )
G5
PEC I H ost
C o n tro lle r
D o m a in 0
0
x
3
0
D o m a in 1
Q u a d -C o re In te l® X e o n ®
P ro c e s s o r 5 3 0 0 S e rie s
(S o c k e t 1 )
G5
6.4.1.1
0
x
3
0
0
x
3
1
D o m a in 0
0
x
3
1
D o m a in 1
TCONTROL and TCC Activation on PECI-Based Systems
Fan speed control solutions based on PECI utilize a TCONTROL value stored in the
processor IA32_TEMPERATURE_TARGET MSR. This MSR uses the same offset
temperature format as PECI, though it contains no sign bit. Thermal management
devices should infer the TCONTROL value as negative. Thermal management algorithms
should utilize the relative temperature value delivered over PECI in conjunction with the
MSR value to control or optimize fan speeds. Figure 6-9 shows a conceptual fan control
diagram using PECI temperatures.
102
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Thermal Specifications
Figure 6-9.
Conceptual Fan Control Diagram For A PECI-Based Platform
TCONTROL
Setting
TCC Activation
Temperature
Max
PECI = 0
Fan Speed
(RPM)
PECI = -10
Min
PECI = -20
Temperature
(not intended to depict actual implementation)
6.4.1.2
Processor Thermal Data Sample Rate and Filtering
The DTS provides an improved capability to monitor device hot spots, which inherently
leads to more varying temperature readings over short time intervals. The DTS sample
interval range can be modified, and a data filtering algorithm can be activated to help
moderate this. The DTS sample interval range is 82 ms (default) to 20 ms (max). This
value can be set in BIOS.
To reduce the sample rate requirements on PECI and improve thermal data stability vs.
time the processor DTS also implements an averaging algorithm that filters the
incoming data. This is an alpha-beta filter with coefficients of 0.5, and is expressed
mathematically as: Current_filtered_temp = (Previous_filtered_temp / 2) +
(new_sensor_temp / 2). This filtering algorithm is fixed and cannot be changed. It is on
by default and can be turned off in BIOS.
Host controllers should utilize the min/max sample times to determine the appropriate
sample rate based on the controller's fan control algorithm and targeted response rate.
The key items to take into account when settling on a fan control algorithm are the DTS
sample rate, whether the temperature filter is enabled, how often the PECI host will
poll the processor for temperature data, and the rate at which fan speed is changed.
Depending on the designer’s specific requirements the DTS sample rate and alpha-beta
filter may have no effect on the fan control algorithm.
6.4.2
PECI Specifications
6.4.2.1
PECI Device Address
The PECI device address for socket 0 is 0x30 and socket 1 is 0x31. Please note that
each address also supports two domains (Domain 0 and Domain 1). For more
information on PECI domains, please refer to the Platform Environment Control
Interface Specification.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
103
Thermal Specifications
6.4.2.2
PECI Command Support
PECI command support is covered in detail in Platform Environment Control Interface
Specification. Please refer to this document for details on supported PECI command
function and codes
6.4.2.3
PECI Fault Handling Requirements
PECI is largely a fault tolerant interface, including noise immunity and error checking
improvements over other compatible industry standard interfaces. The PECI client is as
reliable as the device that it is embedded within, and thus given operating conditions
that fall under the specification, the PECI client will always respond to requests and the
protocol itself can be relied upon to detect any transmission failures. There are,
however, certain scenarios where PECI is known to be unresponsive.
Prior to a power on RESET# and during RESET# assertion, PECI is not guaranteed to
provide reliable thermal data. System designs should implement a default power-on
condition that ensures proper processor operation during the time frame when reliable
data is not available via PECI.
To protect platforms from potential operational or safety issues due to an abnormal
condition on PECI, the PECI host controller should take action to protect the system
from possible damage. It is recommended that the PECI host controller take
appropriate action to protect the client processor device if valid temperature readings
have not been obtained in response to three consecutive gettemp()s or for a one
second time interval. The PECI host controller may also implement an alert to software
in the event of a critical or continuous fault condition.
6.4.2.4
PECI GetTemp0() and GetTemp1() Error Code Support
The error codes supported for the processor GetTemp0() and GetTemp1() command
are listed in Table 6-13 below:
Table 6-13. GetTemp0() and GetTemp1() Error Codes
Error Code
Description
0x8000
General sensor error
0x8002
Sensor is operational, but has detected a temperature below its operational range
(underflow).
§
104
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Features
7
Features
7.1
Power-On Configuration Options
Several configuration options can be configured by hardware. Quad-Core Intel® Xeon®
Processor 5300 Series sample its hardware configuration at reset, on the active-toinactive transition of RESET#. For specifics on these options, please refer to Table 7-1.
The sampled information configures the processor for subsequent operation. These
configuration options cannot be changed except by another reset. All resets reconfigure
the processor, for reset purposes, the processor does not distinguish between a “warm”
reset (PWRGOOD signal remains asserted) and a “power-on” reset.
Table 7-1.
Power-On Configuration Option Lands
Configuration Option
Land Name
Notes
SMI#
1,2,3
Execute BIST (Built-In Self Test)
A3#
1,2
Disable MCERR# observation
A9#
1,2
A10#
1,2
BR[1:0]#
1,2
Output tri state
Disable BINIT# observation
Symmetric agent arbitration ID
Notes:
1.
2.
3.
Asserting this signal during RESET# will select the corresponding option.
Address lands not identified in this table as configuration options should not be asserted during RESET#.
Requires de-assertion of PWRGOOD.
Disabling of any of the cores within the Quad-Core Intel® Xeon® Processor 5300
Series must be handled by configuring the EXT_CONFIG Model Specific Register (MSR).
This MSR will allow for the disabling of a single core per die within the Quad-Core
Intel® Xeon® Processor 5300 Series package. Additional details can be found in the
Conroe and Woodcrest Processor Family BIOS Writer’s Guide.
7.2
Clock Control and Low Power States
Quad-Core Intel® Xeon® Processor 5300 Series support the Extended HALT state (also
referred to as C1E) in addition to the HALT state and Stop-Grant state to reduce power
consumption by stopping the clock to internal sections of the processor, depending on
each particular state. See Figure 7-1 for a visual representation of the processor low
power states. The Extended HALT state is a lower power state than the HALT state or
Stop Grant state.
The Extended HALT state must be enabled via the BIOS for the processor to
remain within its specifications. Refer to the Conroe and Woodcrest Processor
Family BIOS Writer’s Guide. For processors that are already running at the lowest bus
to core frequency ratio for its nominal operating point, the processor will transition to
the HALT state instead of the Extended HALT state.
The Stop Grant state requires chipset and BIOS support on multiprocessor systems. In
a multiprocessor system, all the STPCLK# signals are bussed together, thus all
processors are affected in unison. When the STPCLK# signal is asserted, the processor
enters the Stop Grant state, issuing a Stop Grant Special Bus Cycle (SBC) for each
processor. The chipset needs to account for a variable number of processors asserting
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
105
Features
the Stop Grant SBC on the bus before allowing the processor to be transitioned into one
of the lower processor power states. Refer to the applicable chipset specification and
the Conroe and Woodcrest Processor Family BIOS Writer’s Guide for more information.
7.2.1
Normal State
This is the normal operating state for the processor.
7.2.2
HALT or Extended HALT State
The Extended HALT state (C1E) is enabled via the BIOS. Refer to the Conroe and
Woodcrest Processor Family BIOS Writer’s Guide. The Extended HALT state must be
enabled for the processor to remain within its specifications. The Extended HALT
state requires support for dynamic VID transitions in the platform.
7.2.2.1
HALT State
HALT is a low power state entered when the processor has executed the HALT or
MWAIT instruction. When one of the processor cores execute the HALT or MWAIT
instruction, that processor core is halted; however, the other processor continues
normal operation. The processor will transition to the Normal state upon the occurrence
of SMI#, BINIT#, INIT#, LINT[1:0] (NMI, INTR), or an interrupt delivered over the
front side bus. RESET# will cause the processor to immediately initialize itself.
The return from a System Management Interrupt (SMI) handler can be to either
Normal Mode or the HALT state. See the Intel® 64 and IA-32 Intel® Architecture
Software Developer's Manual, Volume III: System Programming Guide for more
information.
The system can generate a STPCLK# while the processor is in the HALT state. When the
system deasserts STPCLK#, the processor will return execution to the HALT state.
While in HALT state, the processor will process front side bus snoops and interrupts.
7.2.2.2
Extended HALT State
Extended HALT state is a low power state entered when all four processor cores have
executed the HALT or MWAIT instructions and Extended HALT state has been enabled
via the BIOS. When one of the processor cores executes the HALT instruction, that
processor core is halted; however, the other processor cores continue normal
operation. The Extended HALT state is a lower power state than the HALT state or Stop
Grant state. The Extended HALT state must be enabled for the processor to remain
within its specifications.
The processor will automatically transition to a lower core frequency and voltage
operating point before entering the Extended HALT state. Note that the processor FSB
frequency is not altered; only the internal core frequency is changed. When entering
the low power state, the processor will first switch to the lower bus to core frequency
ratio and then transition to the lower voltage (VID).
While in the Extended HALT state, the processor will process bus snoops. The processor
exits the Extended HALT state when a break event occurs. When the processor exits
the Extended HALT state, it will first transition the VID to the original value and then
change the bus to core frequency ratio back to the original value.
106
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Features
Table 7-2.
Extended HALT Maximum Power
B-3 Stepping
G-0 Stepping
FSB Speed
(MHz)
TCASE
(°C)
Max
(W)
TCASE
(°C)
PEXTENDED_HALT QuadCore Intel® Xeon®
Processor E5300 Series
1333
50
30/34
1066
50
30/34
PEXTENDED_HALT QuadCore Intel® Xeon®
Processor X5300 Series
1333
50
PEXTENDED_HALT QuadCore Intel® Xeon®
Processor X5365 Series
1333
PEXTENDED_HALT QuadCore Intel® Xeon®
Processor L5300 Series
PEXTENDED_HALT QuadCore Intel® Xeon®
Processor L5318
Symbol
Max
(W)
Notes
40/50
25/34
1,2,3
50
30/34
1,2
50
40
25
1
50
50
40
25
1
1333
50
24
50
24
1
1066
50
24
50
24
1
1066
50
24
50
24
1
Notes:
1.
These specifications are based on silicon characterization.
2.
Processors running in the lowest bus ratio will enter the HALT state when the processor has executed the
HALT and MWAIT instruction since the processor is already in the lowest core frequency and voltage
operating point. Values represent SKUs with Extended HALT state (25W/30W) and without Extended HALT
state (34W).
3.
G-0 stepping SKUs with Extended HALT state are specified at TCASE = 40°C.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
107
Features
Figure 7-1.
Stop Clock State Machine
HALT or MWAIT Instruction and
HALT Bus Cycle Generated
Normal State
Normal execution
S
De TPC
-a LK
ss #
er
te
d
STPCLK#
De-asserted
S
A s TP C
se L
rte K#
d
STPCLK#
Asserted
INIT#, BINIT#, INTR, NMI, SMI#,
RESET#, FSB interrupts
Extended HALT or HALT State
BCLK running
Snoops and interrupts allowed
Snoop
Event
Occurs
Snoop
Event
Serviced
Extended HALT Snoop or HALT
Snoop State
BCLK running
Service snoops to caches
Stop Grant State
BCLK running
Snoops and interrupts allowed
7.2.3
Snoop Event Occurs
Snoop Event Serviced
Stop Grant Snoop State
BCLK running
Service snoops to caches
Stop-Grant State
When the STPCLK# pin is asserted, the Stop-Grant state of the processor is entered
20 bus clocks after the response phase of the processor issued Stop Grant
Acknowledge special bus cycle. The Quad-Core Intel® Xeon® Processor 5300 Series
will issue two Stop Grant Acknowledge special bus cycles, once for each die. Once the
STPCLK# pin has been asserted, it may only be deasserted once the processor is in the
Stop Grant state. All processor cores will enter the Stop-Grant state once the STPCLK#
pin is asserted. Additionally, all processor cores must be in the Stop Grant state before
the deassertion of STPCLK#.
Since the AGTL+ signal pins receive power from the front side bus, these pins should
not be driven (allowing the level to return to VTT) for minimum power drawn by the
termination resistors in this state. In addition, all other input pins on the front side bus
should be driven to the inactive state.
BINIT# will not be serviced while the processor is in Stop-Grant state. The event will be
latched and can be serviced by software upon exit from the Stop Grant state.
RESET# will cause the processor to immediately initialize itself, but the processor will
stay in Stop-Grant state. A transition back to the Normal state will occur with the deassertion of the STPCLK# signal.
108
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Features
A transition to the Grant Snoop state will occur when the processor detects a snoop on
the front side bus (see Section 7.2.4.1).
While in the Stop-Grant state, SMI#, INIT#, BINIT# and LINT[1:0] will be latched by
the processor, and only serviced when the processor returns to the Normal state. Only
one occurrence of each event will be recognized upon return to the Normal state.
While in Stop-Grant state, the processor will process snoops on the front side bus and it
will latch interrupts delivered on the front side bus.
The PBE# signal can be driven when the processor is in Stop-Grant state. PBE# will be
asserted if there is any pending interrupt latched within the processor. Pending
interrupts that are blocked by the EFLAGS.IF bit being clear will still cause assertion of
PBE#. Assertion of PBE# indicates to system logic that it should return the processor to
the Normal state.
7.2.4
Extended HALT Snoop or HALT Snoop State, Stop Grant
Snoop State
The Extended HALT Snoop state is used in conjunction with the Extended HALT state. If
the Extended HALT state is not enabled in the BIOS, the default Snoop state entered
will be the HALT Snoop state. Refer to the sections below for details on HALT Snoop
state, Stop Grant Snoop state and Extended HALT Snoop state.
7.2.4.1
HALT Snoop State, Stop Grant Snoop State
The processor will respond to snoop or interrupt transactions on the front side bus
while in Stop-Grant state or in HALT state. During a snoop or interrupt transaction, the
processor enters the HALT/Grant Snoop state. The processor will stay in this state until
the snoop on the front side bus has been serviced (whether by the processor or another
agent on the front side bus) or the interrupt has been latched. After the snoop is
serviced or the interrupt is latched, the processor will return to the Stop-Grant state or
HALT state, as appropriate.
7.2.4.2
Extended HALT Snoop State
The Extended HALT Snoop state is the default Snoop state when the Extended HALT
state is enabled via the BIOS. The processor will remain in the lower bus to core
frequency ratio and VID operating point of the Extended HALT state.
While in the Extended HALT Snoop state, snoops and interrupt transactions are handled
the same way as in the HALT Snoop state. After the snoop is serviced or the interrupt is
latched, the processor will return to the Extended HALT state.
7.3
Enhanced Intel SpeedStep® Technology
Quad-Core Intel® Xeon® Processor 5300 Series support Enhanced Intel SpeedStep®
Technology. This technology enables the processor to switch between multiple
frequency and voltage points, which results in platform power savings. Enhanced Intel
SpeedStep Technology requires support for dynamic VID transitions in the platform.
Switching between voltage/frequency states is software controlled. For more
configuration details also refer to the Conroe and Woodcrest Processor Family BIOS
Writer’s Guide.
Note:
Not all Quad-Core Intel® Xeon® Processor 5300 Series are capable of supporting
Enhanced Intel SpeedStep Technology. More details on which processor frequencies will
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
109
Features
support this feature will be provided in future releases of the Quad-Core Intel® Xeon®
Processor 5300 Series NDA Specification Update when available.
Enhanced Intel SpeedStep Technology creates processor performance states (P-states)
or voltage/frequency operating points. P-states are lower power capability states within
the Normal state as shown in Figure 7-1. Enhanced Intel SpeedStep Technology
enables real-time dynamic switching between frequency and voltage points. It alters
the performance of the processor by changing the bus to core frequency ratio and
voltage. This allows the processor to run at different core frequencies and voltages to
best serve the performance and power requirements of the processor and system. The
Quad-Core Intel® Xeon® Processor 5300 Series have hardware logic that coordinates
the requested voltage (VID) between the processor cores. The highest voltage that is
requested from the four processor cores is selected for that processor package. Note
that the front side bus is not altered; only the internal core frequency is changed. In
order to run at reduced power consumption, the voltage is altered in step with the bus
ratio.
The following are key features of Enhanced Intel SpeedStep Technology:
• Multiple voltage/frequency operating points provide optimal performance at
reduced power consumption.
• Voltage/frequency selection is software controlled by writing to processor MSR’s
(Model Specific Registers), thus eliminating chipset dependency.
— If the target frequency is higher than the current frequency, VCC is incremented
in steps (+12.5 mV) by placing a new value on the VID signals and the
processor shifts to the new frequency. Note that the top frequency for the
processor can not be exceeded.
— If the target frequency is lower than the current frequency, the processor shifts
to the new frequency and VCC is then decremented in steps (-12.5 mV) by
changing the target VID through the VID signals.
See the Conroe and Woodcrest Processor Family BIOS Writer’s Guide for specific
information to enable and configure Enhanced Intel SpeedStep Technology in BIOS.
§
110
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
8
Boxed Processor Specifications
8.1
Introduction
Intel boxed processors are intended for system integrators who build systems from
components available through distribution channels. The Quad-Core Intel® Xeon®
Processor 5300 Series will be offered as an Intel boxed processor.
Intel will offer the Quad-Core Intel® Xeon® Processor 5300 Series boxed processor
with two heat sink configurations available for each processor frequency: 1U passive/
3U+ active combination solution and a 2U passive only solution. The 1U passive/3U+
active combination solution is based on a 1U passive heat sink with a removable fan
that will be pre-attached at shipping. This heat sink solution is intended to be used as
either a 1U passive heat sink, or a 3U+ active heat sink. Although the active
combination solution with removable fan mechanically fits into a 2U keepout, its use is
not recommended in that configuration.
The 1U passive/3U+ active combination solution in the active fan configuration is
primarily designed to be used in a pedestal chassis where sufficient air inlet space is
present and strong side directional airflow is not an issue. The 1U passive/3U+ active
combination solution with the fan removed and the 2U passive thermal solution require
the use of chassis ducting and are targeted for use in rack mount or pedestal servers.
The retention solution used for these products is called the Common Enabling Kit, or
CEK. The CEK base is compatible with both thermal solutions and uses the same hole
locations as the Dual-Core Intel® Xeon® processor 5100 series.
The 1U passive/3U+ active combination solution will utilize a removable fan capable of
4-pin pulse width modulated (PWM) control. Use of a 4-pin PWM controlled active
thermal solution helps customers meet acoustic targets in pedestal platforms through
the motherboards’s ability to directly control the RPM of the processor heat sink fan.
See Section 8.3 for more details on fan speed control, and see Section 6.4 for more on
the PWM and PECI interface along with Digital Thermal Sensors (DTS). Figure 8-1
through Figure 8-3 are representations of the two heat sink solutions.
Figure 8-1.
Boxed Quad-Core Intel® Xeon® Processor 5300 Series 1U Passive/3U+
Active Combination Heat Sink (With Removable Fan)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
111
Boxed Processor Specifications
Figure 8-2.
Boxed Quad-Core Intel® Xeon® Processor 5300 Series 2U Passive Heat Sink
Figure 8-3.
2U Passive Quad-Core Intel® Xeon® Processor 5300 Series Processor
Thermal Solution (Exploded View)
Heat sink
screws
Heat sink screw
springs
Heat sink
Heat sink standoffs
Thermal Interface
Material
Motherboard
and
processor
Protective Tape
CEK spring
Chassis pan
Note:
1.
The heat sinks and fan assemblies represented in Figure 8-1, Figure 8-2, and Figure 8-3 are for reference
only, and may not represent the final boxed processor heat sinks.
2.
The screws, springs, and standoffs will be captive to the heat sink. This image shows all of the components
in an exploded view.
3.
It is intended that the CEK spring will ship with the base board and be pre-attached prior to shipping.
112
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
8.2
Mechanical Specifications
This section documents the mechanical specifications of the boxed processor.
8.2.1
Boxed Processor Heat Sink Dimensions (CEK)
The boxed processor will be shipped with an unattached thermal solution. Clearance is
required around the thermal solution to ensure unimpeded airflow for proper cooling.
The physical space requirements and dimensions for the boxed processor and
assembled heat sink are shown in Figure 8-4 through Figure 8-8. Figure 8-9 through
Figure 8-10 are the mechanical drawings for the 4-pin board fan header and 4-pin
connector used for the active CEK fan heat sink solution.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
113
Boxed Processor Specifications
Figure 8-4.
114
Top Side Board Keepout Zones (Part 1)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
Figure 8-5.
Top Side Board Keepout Zones (Part 2)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
115
Boxed Processor Specifications
Figure 8-6.
116
Bottom Side Board Keepout Zones
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
Figure 8-7.
Board Mounting-Hole Keepout Zones
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
117
Boxed Processor Specifications
Figure 8-8.
118
Volumetric Height Keep-Ins
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
Figure 8-9.
4-Pin Fan Cable Connector (For Active CEK Heat Sink)
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
119
Boxed Processor Specifications
Figure 8-10. 4-Pin Base Board Fan Header (For Active CEK Heat Sink)
120
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
8.2.2
Boxed Processor Heat Sink Weight
8.2.2.1
Thermal Solution Weight
The 1U passive/3U+ active combination heat sink solution and the 2U passive heat sink
solution will not exceed a mass of 1050 grams. Note that this is per processor, a dual
processor system will have up to 2100 grams total mass in the heat sinks. This large
mass will require a minimum chassis stiffness to be met in order to withstand force
during shock and vibration.
See Section 3 for details on the processor weight.
8.2.3
Boxed Processor Retention Mechanism and Heat Sink
Support (CEK)
Baseboards and chassis designed for use by a system integrator should include holes
that are in proper alignment with each other to support the boxed processor. Refer to
the Server System Infrastructure Specification (SSI-EEB 3.6, TEB 2.1 or CEB 1.1).
These specification can be found at: http://www.ssiforum.org.
Figure 8-3 illustrates the Common Enabling Kit (CEK) retention solution. The CEK is
designed to extend air-cooling capability through the use of larger heat sinks with
minimal airflow blockage and bypass. CEK retention mechanisms can allow the use of
much heavier heat sink masses compared to legacy limits by using a load path directly
attached to the chassis pan. The CEK spring on the secondary side of the baseboard
provides the necessary compressive load for the thermal interface material. The
baseboard is intended to be isolated such that the dynamic loads from the heat sink are
transferred to the chassis pan via the stiff screws and standoffs. The retention scheme
reduces the risk of package pullout and solder joint failures.
All components of the CEK heat sink solution will be captive to the heat sink and will
only require a Phillips screwdriver to attach to the chassis pan. When installing the
CEK, the CEK screws should be tightened until they will no longer turn easily. This
should represent approximately 6-8 inch-pounds of torque. More than that may
damage the retention mechanism components.
8.3
Electrical Requirements
8.3.1
Fan Power Supply (Active CEK)
The 4-pin PWM controlled active thermal solution is being offered to help provide better
control over pedestal chassis acoustics. This is achieved though more accurate
measurement of processor die temperature through the processor’s Digital Thermal
Sensors. Fan RPM is modulated through the use of an ASIC located on the baseboard,
that sends out a PWM control signal to the 4th pin of the connector labeled as Control.
This thermal solution requires a constant +12 V supplied to pin 2 of the active thermal
solution and does not support variable voltage control or 3-pin PWM control. See
Table 8-2 for details on the 4-pin active heat sink solution connectors.
If the 4-pin active fan heat sink solution is connected to an older 3-pin baseboard CPU
fan header it will default back to a thermistor controlled mode, allowing compatibility
with legacy 3-wire designs. When operating in thermistor controlled mode, fan RPM is
automatically varied based on the TINLET temperature measured by a thermistor
located at the fan inlet of the heat sink solution.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
121
Boxed Processor Specifications
The fan power header on the baseboard must be positioned to allow the fan heat sink
power cable to reach it. The fan power header identification and location must be
documented in the suppliers platform documentation, or on the baseboard itself. The
baseboard fan power header should be positioned within 177.8 mm [7 in.] from the
center of the processor socket.
Table 8-1.
Table 8-2.
PWM Fan Frequency Specifications for 4-Pin Active CEK Thermal Solution
Description
Min Frequency
Nominal Frequency
Max Frequency
Unit
PWM Control
Frequency Range
21,000
25,000
28,000
Hz
Fan Specifications for 4-Pin Active CEK Thermal Solution
Min
Typ
Steady
+12 V: 12 volt fan power supply
10.8
IC: Fan Current Draw
N/A
2
Description1
SENSE: SENSE frequency
Max
Steady
Max
Startup
12
12
13.2
V
1
1.25
1.5
A
2
2
2
Pulses per fan
revolution
Unit
Note:
1.
System board should pull this pin up to Vcc with a resistor
Figure 8-11. Fan Cable Connector Pin Out for 4-Pin Active CEK Thermal Solution
Table 8-3.
Fan Cable Connector Pin Out for 4-Pin Active CEK Thermal Solution
Note:
8.3.2
Pin Number
Signal
Color
1
Ground
Black
2
Power: (+12 V)
Yellow
3
Sense: 2 pulses per revolution
Green
4
Control: 21 KHz-28 KHz
Blue
System board should provide an open drain / open collector for pin 4. Fan will pull this pin up to a
specific voltage (5.25V max).
Boxed Processor Cooling Requirements
As previously stated the boxed processor will be available in two product
configurations. Each configuration will require unique design considerations. Meeting
the processor’s temperature specifications is also the function of the thermal design of
the entire system, and ultimately the responsibility of the system integrator. The
processor temperature specifications are found in Section 6 of this document.
122
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Boxed Processor Specifications
8.3.2.1
1U Passive/3U+ Active Combination Heat Sink Solution (1U Rack
Passive)
In the 1U configuration it is assumed that a chassis duct will be implemented to provide
a minimum airflow of 15 cfm at 0.38 in. H2O (25.5 m3/hr at 94.6 Pa) of flow
impedance. The duct should be carefully designed to minimize the airflow bypass
around the heatsink. It is assumed that a 40°C TLA is met. This requires a superior
chassis design to limit the TRISE at or below 5°C with an external ambient temperature
of 35° C. Following these guidelines will allow the designer to meet Quad-Core Intel®
Xeon® Processor X5300 Series Thermal Profile and conform to the thermal
requirements of the processor.
8.3.2.2
1U Passive/3U+ Active Combination Heat Sink Solution (Pedestal
Active)
The active configuration of the combination solution is designed to help pedestal
chassis users to meet the thermal processor requirements without the use of chassis
ducting. It may be still be necessary to implement some form of chassis air guide or air
duct to meet the TLA temperature of 40° C depending on the pedestal chassis layout.
Also, while the active thermal solution design will mechanically fit into a 2U volumetric,
it may not provide adequate airflow. This is due to the requirement of additional space
at the top of the thermal solution to allow sufficient airflow into the heat sink fan. Use
of the active configuration in a 2U rackmount chassis is not recommended.
It is recommended that the ambient air temperature outside of the chassis be kept at
or below 35°C. The air passing directly over the processor thermal solution should not
be preheated by other system components. Meeting the processor’s temperature
specification is the responsibility of the system integrator.
8.3.2.3
2U Passive Heat Sink Solution (2U+ Rack or Pedestal)
In the 2U+ passive configuration it is assumed that a chassis duct will be implemented
to provide a minimum airflow of 27 cfm at 0.182 in. H2O (45.9 m3/hr at 45.3 Pa) of
flow impedance. The duct should be carefully designed to minimize the airflow bypass
around the heatsink. The TLA temperature of 40° C should be met. This may require the
use of superior design techniques to keep TRISE at or below 5°C based on an ambient
external temperature of 35°C.
8.4
Boxed Processor Contents
A direct chassis attach method must be used to avoid problems related to shock and
vibration, due to the weight of the thermal solution required to cool the processor. The
board must not bend beyond specification in order to avoid damage. The boxed
processor contains the components necessary to solve both issues. The boxed
processor will include the following items:
• Quad-Core Intel® Xeon® Processor 5300 Series
• Unattached heat sink solution
• Four screws, four springs, and four heat sink standoffs (all captive to the heat sink)
• Foam air bypass pad and skirt (included with 1U passive/3U+ active solution)
• Thermal interface material (pre-applied on heat sink)
• Installation and warranty manual
• Intel Inside Logo
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
123
Boxed Processor Specifications
The other items listed in Figure 8-3 that are required to compete this solution will be
shipped with either the chassis or boards. They are as follows:
• CEK Spring (supplied by baseboard vendors)
• Heat sink standoffs (supplied by chassis vendors)
§
124
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
Debug Tools Specifications
9
Debug Tools Specifications
Please refer to the Debug Port Design Guide for UP/DP Systems and the appropriate
platform design guidelines for information regarding debug tool specifications.
Section 1.3 provides collateral details.
9.1
Debug Port System Requirements
The Quad-Core Intel® Xeon® Processor 5300 Series debug port is the command and
control interface for the In-Target Probe (ITP) debugger. The ITP enables run-time
control of the processors for system debug. The debug port, which is connected to the
FSB, is a combination of the system, JTAG and execution signals. There are several
mechanical, electrical and functional constraints on the debug port that must be
followed. The mechanical constraint requires the debug port connector to be installed in
the system with adequate physical clearance. Electrical constraints exist due to the
mixed high and low speed signals of the debug port for the processor. While the JTAG
signals operate at a maximum of 75 MHz, the execution signals operate at the common
clock FSB frequency. The functional constraint requires the debug port to use the JTAG
system via a handshake and multiplexing scheme.
In general, the information in this chapter may be used as a basis for including all runcontrol tools in Quad-Core Intel® Xeon® Processor 5300 Series based systems designs
including tools from vendors other than Intel.
Note:
The debug port and JTAG signal chain must be designed into the processor board to
utilize the XDP for debug purposes except for interposer solutions.
9.2
Target System Implementation
9.2.1
System Implementation
Specific connectivity and layout guidelines for the Debug Port are provided in the
Debug Port Design Guide for UP/DP Systems and the appropriate platform design
guidelines.
9.3
Logic Analyzer Interface (LAI)
Intel is working with two logic analyzer vendors to provide logic analyzer interfaces
(LAIs) for use in debugging Quad-Core Intel® Xeon® Processor 5300 Series systems.
Tektronix and Agilent should be contacted to obtain specific information about their
logic analyzer interfaces. The following information is general in nature. Specific
information must be obtained from the logic analyzer vendor.
Due to the complexity of Quad-Core Intel® Xeon® Processor 5300 Series based
multiprocessor systems, the LAI is critical in providing the ability to probe and capture
FSB signals. There are two sets of considerations to keep in mind when designing a
Quad-Core Intel® Xeon® Processor 5300 Series based system that can make use of an
LAI: mechanical and electrical.
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet
125
Debug Tools Specifications
9.3.1
Mechanical Considerations
The LAI is installed between the processor socket and the processor. The LAI plugs into
the socket, while the processor plugs into a socket on the LAI. Cabling that is part of
the LAI egresses the system to allow an electrical connection between the processor
and a logic analyzer. The maximum volume occupied by the LAI, known as the keepout
volume, as well as the cable egress restrictions, should be obtained from the logic
analyzer vendor. System designers must make sure that the keepout volume remains
unobstructed inside the system. In some cases, it is known that some of the electrolytic
capacitors fall inside of the keepout volume for the LAI. In this case, it is necessary to
move these capacitors to the backside of the board before using the LAI. Additionally,
note that it is possible that the keepout volume reserved for the LAI may include
different requirements from the space normally occupied by the heatsink. If this is the
case, the logic analyzer vendor will provide either a cooling solution as part of the LAI
or additional hardware to mount the existing cooling solution.
9.3.2
Electrical Considerations
The LAI will also affect the electrical performance of the FSB, therefore it is critical to
obtain electrical load models from each of the logic analyzer vendors to be able to run
system level simulations to prove that their tool will work in the system. Contact the
logic analyzer vendor for electrical specifications and load models for the LAI solution
they provide.
§
126
Quad-Core Intel® Xeon® Processor 5300 Series Datasheet

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project