Toshiba SR-M8102 Computer Drive User manual


Add to my manuals
16 Pages

advertisement

Toshiba SR-M8102 Computer Drive User manual | Manualzz

TOSHIBA AMERICA INFORMATION SYSTEMS

STORAGE DEVICE DIVISION

IRVINE, CALIFORNIA

SR-M8102

CD-R/CD-RW DRIVE

USER MANUAL

CONTENTS

Introduction..............................................................................1

Setup ........................................................................................3

Using the CD-R/CD-RW Drive .................................................6

Troubleshooting.......................................................................9

Specifications ........................................................................10

Drive Connectors...................................................................13

INTRODUCTION – SR-M8102

General Features

CD-R/CD-RW disc write/rewrite at 52X/32X

3-way Disc Eject (eject button, software, emergency eject hole)

Average Random Access Time

CD 110ms

CD-RW 120ms

Horizontal or Vertical Mount

2MByte Buffer

Playback interchangeability for CD-ROM discs

BUS Interface - ATAPI

Formats Compatibility

CD-DA (Red Book) - Standard Audio CD & CD-TEXT

CD-ROM (Yellow Book Mode 1&2) - Standard Data

CD-ROM XA (Mode 2 Form 1&2) - Photo CD, Multi Session

CD-I/FMV (Green Book, Mode 2 Form 1&2, Ready, Bridge)

CD-Extra/CD-Plus (Blue Book) - Audio & Text/Video

Video-CD (White Book)- MPEG1Video

CD-R (Orange Book Part II)

CD-RW & HSRW (Orange Book Part III, Volume 1&2)

USRW

1

Front Panel

Figure 1.SR-M8102 CD-R/RW Drive Front Panel

Loading

Tray

LED

Load/Unload

Button

Emergency

Eject Hole

Load disc using tray.

The LED lights when the drive is operating

The Load/Unload button is used to open the disc tray so you can install or remove a disc.

The emergency eject hole is to be used only when the Loading Tray will not open when Eject button is pressed.

SETUP – SR-M8102

The following steps must be performed to properly install your drive:

• Set Drive Jumper Settings

• Connect Audio Cable

• Attach IDE BUS Cable

• Attach Power Cable

• Mount Drive

Jumper Settings

The mode select jumpers are 6 straight angle pins located on the rear of the CD-R/CD-RW drive.

By placing a jumper on the pins, you can select the following functions:

CS Drive is configured using host interface signal CSEL

SL Configures drive as Slave

MA Configures drive as Master (default mode)

Figure 1.Mode Select Jumper

In most installations, jumper should remain in the MA position (factory default). It is recommended that you install your CD-R/CD-RW drive only on the secondary IDE BUS. If you are installing on primary IDE

BUS, your hard drive would then be the Master, and you should set your CD-R/CD-RW drive to the

Slave position (SL)

Figure 2.Jumper Locations

3

Placing CD-R/CD-RW Drive inside your Computer

Now that you have set the jumpers, you are ready to install your CD-R/CD-RW drive inside your computer.

Important Note: Disconnect power from your computer system before beginning installation.

Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the CD-R/CD-RW drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system.

Your Toshiba CD-R/CD-RW drive can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.)

Carefully start sliding the CD-R/CD-RW drive into the opening with the disc tray facing the front of the computer. Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio cable and the Power cable on the back of the drive.

Connecting Cables

IDE BUS Cable (not supplied with drive) - Your computer system should have a primary and secondary

IDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUS cable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the CD-R/CD-

RW drive's interface connector:

If you are replacing your CD-ROM or DVD: connect CD-R/CD-RW drive to the BUS Cable connector that the CD-ROM or DVD was connected to.

Figure 3.Installing BUS Cable

If CD-R/CD-RW drive is not replacing a CD-ROM/DVD

or is an addition to a CD-ROM/DVD: connect CD-R/CD-RW drive to an open connector on the secondary IDE BUS cable (not supplied with drive).

If CD-R/CD-RW drive is to be slave on Primary BUS: connect CD-R/CD-RW drive to open connector on the primary IDE BUS cable (not supplied with drive).

4

Power Cable - Connect an internal computer power supply cable to the power socket at the back of the CD-

R/CD-RW drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly.

Figure 4.Installing Power Cable

Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable.

Toshiba's CD-R/CD-RW drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the CD-

R/CD-RW drive (see CD-R/CD-RW drive Back Panel photo for location). Refer to the instructions that came with your sound card for details on any sound-driver software required

.

Figure 5.Installing Audio Cable

Completing Installation

After you have connected all the necessary cables, push the CD-R/CD-RW drive completely into the computers drive slot. Mount drive per your computers instructions. The screw length should not exceed

30.5mm (measured from outside surface of side or bottom of drive to tip of screw). Replace computer cover and all outer screws.

Figure 6.Mounting Illustration

Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows

'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If you prefer using DOS, download the DOS ATAPI driver from our web site.

Other Software - Additional software is required to use the SR-M8102 CD-R/-RW functions.

5

USING THE CD-R/CD-RW Drive – SR-M8102

Drive Operation

Inserting a Disc - Horizontally

To insert a disc into a drive that is mounted horizontally, perform the following steps:

Figure 1.Inserting Disc

1. Open the drive's Loading tray by pressing the Eject Button.

2. Place disc or into drive's Loading tray

3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.

Inserting a Disc - Vertically

To insert a disc in a drive that is mounted vertically, perform the following steps:

1. Locate sliding disc holders (4 locations) on drive's Loading Tray.

2. The vertical position of the drive (eject button up or down) determines which of these four sliding disc holders are used (see photo below). Position the disc behind 3 of the disc holders, two on bottom, and one on upper rear, closest to drive). Using all four holders may cause the disc to not set properly in tray.

3. Slide the disc holders towards the center of tray using your finger, opened paper clip or the end of the emergency eject tool. The holder in the upper front side should be pulled away from the center of tray.

4. Position the disc behind disc holders on upper and rear side of tray. Then put disc behind bottom front holder

Check to see that all three disc holders are holding disc securely.

Close the drive by gently pushing in the tray or pressing the eject button.

6

Figure 2.Inserting Disc Vertically

Removing a Disc

To remove a disc from the CD-R/CD-RW drive, perform the following steps:

1. Open the Loading Tray by pressing the Eject Button.

2. Slide disc holders away from disc.

3. Grasp disc by edges, and lift out of loading tray.

4. Press Eject Button again to close Loading Tray.

CD-RW Software

Additional software is required to use the SR-M8102 CD-R/-RW functions

Usage Guidelines

• Keep the disc tray closed when not using the CD-R/CD-RW Drive.

• Do not press down on the disc tray when opening or closing it.

• Do not place objects on the disc tray.

• Never use a damaged, broken, or deformed disc.

• Do not press the Open/Close button while the drive is accessing a disc.

NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed technology and do not indicate a problem with the drive.

Emergency Ejection

CAUTION: The following procedure is intended only as a last resort when pressing the

eject button fails to open the Loading Tray

1. Turn computer power OFF by properly shutting down system.

2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in until loading tray opens. Pull tray out.

7

Figure 3.Using Emergency Eject

Cleaning Media

Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc accessing speed.

If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather from the inner side outward.

8

TROUBLESHOOTING – SR-M8102

Problem

Disc tray cannot be opened

Drive is not recognized by system

Drive is not recognized by system during Boot process, but is recognized by the Operating

System (i.e. XP, Win2000, Win98,

Win NT, etc.)

BUSY Indicator LED flashes slowly

BUSY Indicator LED is constantly

ON

CD-R/RW can not play certain types of CD media (i.e. CD-plus, etc.)

Solution

Check that there is power to drive.

Use Emergency Eject instructions to open tray.

Is the drive connected properly? Are all cables plugged in properly (e.g.

Power Cable, Interface Cable and Audio Cables).

Are the drive configuration jumpers on the CD-R/CD-RW drive set properly?

Is the software driver loaded? On a step-by-step (F8) Boot of the system is the CD-R/CD-RW drive recognized?

(BIOS / DOS reports "device driver not found" or "no valid drivers selected."). If not, Contact Technical Support.

Has the CD-R/CD-RW drive software driver been corrupted by a virus.

Run a Virus Scan program and repair if possible. Contact Technical

Support if the Virus renders the CD-R/CD-RW drive software drivers not useable.

Is the CD-R/CD-RW drive software driver loaded? On a step-by-step

(F8) Boot of the system is the CD-R/CD-RW drive recognized?

(BIOS / DOS reports "device driver not found"). If not, Contact Technical

Support.

Has the Windows CD-R/CD-RW drive software driver program been corrupted by a virus. Run a Virus Scan program and repair if possible.

Contact Technical Support if the Virus renders the software drivers not useable.

The disc may be dirty Clean it with a soft damp cloth. Avoid cleaning the disc using a circular motion. The disc should be wiped in a radial direction. That is, from the inner side outward.

The laser lens may have become cloudy or blocked by particulate matter. Please contact Technical Support.

Possible Hardware Problem. Please contact Technical Support.

Is the CD-R/CD-RW drive driver loaded

Is the CD disc the correct format for the type of system that you are using? (i.e. on a PC an ISO9660 IBM compatible PC format as opposed to Apple/Mac HFS disc or UNIX disc formats which will not function).

Do you have the correct software applications program/drivers installed to run a CD-R/RW disc?

Has the Windows CD-R/CD-RW drive software driver program been corrupted by a virus. Run a Virus Scan program and repair if possible.

Contact Technical Support if the Virus renders the software drivers not useable.

9

SPECIFICATIONS –SR-M8102

General

Interface ATAPI

Format for Writing: Disc at once, Track at once, Session at once, Variable & Fixed Packet write

Format Compatibility: CD-DA (Red Book) - Standard Audio CD & CD-TEXT

CD-ROM (Yellow Book Mode 1&2) - Standard Data

CD-ROM XA (Mode 2 Form 1&2) - Photo CD, Multi Session

CD-I/FMV (Green Book, Mode 2 Form 1&2, Ready, Bridge)

Video-CD (White Book)- MPEG1 Video

CD-R (Orange Book Part II)

CD-RW & HSRW (Orange Book Part III, Volume 1&2)

USRW

Media Compatibility 120mm CD-ROM (Read Only)

80mm CD (Horizontal Mount Only)

80/700/650 CD- Recordable (Read & Write)

700/650MB CD-Rewritable (Read& Write)

700/650MB High Speed CD-Rewritable (Read & Write)

700/650MB Ultra Speed CD-Rewritable (Read & Write)

Note: All CD formats, except CD-Red Book (audio), require additional application specific software and/or hardware. The drive is capable of reading these data formats. However, in order to run applications that

use these formats, you must first have the required software and/or hardware.

Performance

Read Speed:

CD-DA (Audio Play): Analog

CD-DA (DAE): Digital

Mixed CD: Audio

Mixed CD: Data

8X CLV

48X CAV

48X CAV

48X CAV

TOC Read

Write Speed:

8X CAV

CD-Rewritable (Standard Speed) 4X CLV

CD-Rewritable (High Speed) 10X/4X CLV

CD-Rewritable (Ultra Speed) 32X/24X PCAV, 16XCLV

10

Transfer Rate

CD-ROM Read (Mode 1)

CD-R/RW Read (Mode 1)

Random Access Time

CD-ROM

CD-RW

7,800KB/second

6,000KB/second

110ms

120ms

Data Buffer 2MB

Environmental

Ambient Temperature

Operating

Storage

Relative Humidity

5° to 45 ° C (41° to 113° F)

-25° to 60° C (13° to 140° F)

10% to 80%

10% to 95%

Operating

Storage/Shipping

Vibration

Operating (Random)

Non-operating (10 to 500Hz)

Shock

Operating (Read)

Operating (Write)

0.5Grms 15min

0.712Grms 15min

11 msec 6G, 2msec 60G

11msec 3G

Acoustical Noise

Power

<54dBA

Physical

11

Connectors

DC input

ATAPI Interface Connector

Audio Connectors

4-pin Power Supply Connector

40 Pin I/F ATAPI Standard

4-pin and 2-pin connector (use matching housing, Part No.

70066, made by Molex Corp, or equivalent)

Regulatory

The SR-M8102 CD-R/RW has been certified by the following regulatory agencies

• UL 1950

• CSA C22.2 No. 950

• TUV (EN60950I)

• CE standard

• DHHS 21 CFR Sub-Chapter J

• FDA CFR21, EN60825

12

DRIVE CONNECTORS –SR-M8102

Figure 1.SR-M8102 CD-R/CD-RW Drive Rear Panel - Connectors

Power

Connector

Power is supplied to your CD-R/RW drive by the connection with your computer's

+5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the power connector fits only one way.

CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in

upside-down with power ON.

Audio

Connectors

Supplies Analog and Digital sound to your system.

ATAPI

Connector

The SR-M8102 CD-R/RW drive is connected to your computer system through the ATAPI connector.

13

Table 1.Interface Pin Assignments

PIN

NO.

1

2

3

4

5

6

7

8

9

I/O

I/O

10 I/O

11 I/O

12 I/O

13 I/O

14 I/O

15 I/O

16 I/O

17 I/O

18 I/O

19 -

20

I/O

I/O

-

HD9

HD5

HD10

HD4

HD11

HD3

HD12

HD2

HD13

HD1

HD14

HD0

HD15

GND

(KEYPIN)

Host Data Bus BIT 9

Host Data Bus BIT 5

Host Data Bus Bit 10

Host Data Bus BIT 4

Host Data Bus BIT 11

Host Data Bus BIT 3

Host Data Bus BIT 12

Host Data Bus BIT 2

Host Data Bus BIT 13

Host Data Bus BIT 1

Host Data Bus BIT 14

Host Data Bus BIT 0

Host Data Bus BIT 15

INTERFACE PIN ASSIGNMENT

I/O SIGNAL

NAME

I

-

I/O

I/O

I/O

Reset

GND

HD7

HD8

HD6

HOST SIGNAL NAME

Host Reset

Host Data Bus BIT 7

Host Data Bus BIT 8

Host Data Bus BIT 6

PIN

NO.

21

22

23

24

25

26

27

28

29

30

-

I

-

31

32

33

O

I

34 I/O

35 I

36

37

38

I

I

I

39 I/O

40

I/O SIGNAL

NAME

HOST SIGNAL NAME

O

-

I

-

I

HDRQ

GND

HWR-,STOP Host I/O Write

GND

HRD-,

HDMARDY, -

HSTROBE

DMA Request

Host I/O Read

-

O

GND

IORDY,

DDMARDY,-

DSTROBE

CSEL

HDAK-

GND

I/O Channel Ready

Cable Select

DMA Acknowledge

-

IOCS16-

HA1

PDIAG-

HA0

HA2

HCS1

HCS3

DASP-

GND

Host 16 BIT I/O

Host Address Bus BIT 1

Passed Diagnostics

Host Address Bus BIT 0

Host Address Bus BIT 2

Host CHIP Select 0

Host CHIP Select 1

Drive Active/Drive 1

Present

14

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement