KTI Networks KGS-0800-4HP User manual

Add to My manuals
4 Pages

advertisement

KTI Networks KGS-0800-4HP User manual | Manualzz

RGS-3084M- E

8-Port GbE Switch with 4 PoE+ PSE Ports

User’s Manual

Doc.161003B

1. Product Overview

The switch is an 8-port 10/100/1000Mbps unmanaged Ethernet switch with 4 PoE+ PSE ports. It is designed to enhance network performance in a compact form factor. The switch can also be rack-mounted with help of rack mounting brackets provided with the switch.

The switch comes with 8 10/100/1000Mbps ports, offering solutions for accelerating bandwidth needs for small Ethernet workgroups. The switch uses store and forward packet-switching technology, which offers reliable data transfer and supports automatic

MDI/MDI-X detection & auto-crossover on all ports which eliminates the need for cross over cables or dedicated uplink ports. Any port can simply connect a server or a switch, using the standard straight-through twisted-pair cable. The switch also supports 4 PoE+ ports that can be used to power up PoE enabled devices. This switch is ideal for network connectivity for the SOHO/SME environment.

2. Product Features

● 8 RJ-45 Ports to support 10BaseT, 100BaseTX and 1000BaseT connectivity

● Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab and IEEE802.3af/at standards

● Supports IEEE802.3 auto-negotiation protocol

● Supports IEEE802.3x flow control for full duplex

● Supports auto MDI/MDI-X crossover

● Supports wire speed packet filtering and forwarding rate

● Supports store-and-forward switching architecture

● Link/ACT LED for each port & PoE LED for PoE ports

3. System Requirements

The following system requirements are recommended:

● Network card for each PC or Server

● Network cables Cat.5 for 1000Mbps

4. Front View

The DIP Switch configuration for supporting 10Mbps transmission with PoE up to 180 meters. Please note, after turning ON the DIP switch you have to reboot the switch.

1

RGS-3084M- E

After installing the switch, you can check its status from the LED indicators on the front panel shown below.

5. LED Description

Following is the LED description:

LED Status

Steady Green

Operation

The switch is powered on.

Power

Off The switch is powered off.

Steady Amber

Steady Green

Port LED

Connected to 10/100M network

Connected to 1000M network

PoE

PoE Alert

Off

Steady Green

Off

On (Green)

Off

No device is connected

Delivering Power to PoE devices.

PoE function not active.

Total PoE power consumed is over 50W

Total PoE power consumed is less than 50W

6. Connecting Computers

The switch features auto-MDI/MDIX crossover detection function and provides plug-and-play capability. Users can immediately use the features of the product simply by plugging the network cables (RJ45) to the computers and the switches.

7. Hardware Installation

1. Connect one Ethernet port to your router’s LAN port with an Ethernet cable.

2. Connect your computer to one port of the switch with an Ethernet cable.

3. Plug DC end of the provided Power Adapter into the power jack of the switch and the

AC end to a standard electrical socket.

8. Uplink

All Ports can be used as an uplink port for connecting another Ethernet switch without using crossover cable. You may extend the network distance more than 100m or the number of connected computers by linking another switch or hub.

2

RGS-3084M- E

9. To prolong the operational life of your units

● Do not stack more than eight units if free standing

● Do not place objects on top of any unit or stack

● Do not obstruct any vents at the sides of the case

10. Package Contents

The following items should be present in the product package:

● The switch unit

● One Power adapter

● One Power cord

● Quick installation guide

● Four Rubber feet

Make sure the package contains above items. If any listed item is damaged or missing, please contact your retailer immediately.

3

RGS-3084M- E

11. Technical Specifications

Hardware

Standard

IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX

IEEE 802.3ab 1000Base-T, IEEE 802.3x Flow Control,

IEEE 802.3af PoE, IEEE 802.3at PoE+

Network Ports

8 10/100/1000Mbps Gigabit copper ports

Shielded RJ-45, auto-negotiation, auto-MDI/MDI-X support

Network Cables Cat. 5, 5e, 6 or higher up to 100m

Power over Ethernet

PoE Power Budget

PoE Alert

MAC Address Table

Buffer Memory

Jumbo Frame

Dimension

Power

Temperature

Humidity

Approval

PSE on Port 1 ~ Port 4, 30W max. per port output

60W max. shared by 4 PSE ports

LED alert when delivered PoE power over 50W

4K entries

1.5M bits

Up to 9K bytes

165 x 118 x 39mm (W x D x H)

External Power 55V/1.3A

Operating: 0° ~ 40°C, Storage: -40° ~ 70°C

10% ~ 90% (non-condensing)

CE/FCC compliance

4

advertisement

Key Features

  • 8 Gigabit Ethernet ports for fast and reliable network connectivity
  • 4 PoE+ ports to power devices like IP cameras, VoIP phones, and wireless access points
  • Unmanaged for simple and cost-effective network management
  • Supports plug-and-play operation for easy installation
  • Metal housing for durability and a limited lifetime warranty for peace of mind

Related manuals

Frequently Answers and Questions

How do I connect my devices to the KGS-0800-4HP?
Simply connect your devices to the switch's Ethernet ports using standard Ethernet cables. The switch will automatically detect the speed and duplex settings of your devices and adjust accordingly.
Can I use the KGS-0800-4HP to power my PoE devices?
Yes, the KGS-0800-4HP has 4 PoE+ ports that can provide up to 30 watts of power each. This is enough to power most PoE devices, such as IP cameras, VoIP phones, and wireless access points.
How do I troubleshoot the KGS-0800-4HP if I'm having problems?
If you're having problems with your KGS-0800-4HP, first check the LEDs on the front of the switch. If any of the LEDs are not lit or are blinking, it may indicate a problem with the switch or your network. You can also try resetting the switch to its factory default settings.
Download PDF

advertisement