Deltec SC 1350 Operating Instructions/Spare Parts List
Deltec SC 1350 is an internal protein skimmer designed for use in filter vats. It features a precision water level controller, silencer, large foam cup, high performance, extremely low energy consumption and quiet operation.
Advertisement
Advertisement
®
SC 1350
Bedienungsanleitung &
Ersatzteilliste
Operating instruction & spare part list
Istruzioni d’uso e parti di ricambio
Instructions d'emploi
Accessoires et pièces détachées
Wichtige Sicherheitshinweise
Warnung: Zum Schutz vor Verletzungen sollten grundlegende Vorsichtsmaßnahmen und folgende
Sicherheitshinweise beachtet werden.
1) Sicherheitshinweise Lesen und befolgen
2) Gefahr: Zur Vermeidung eines elektrischen Schlages sollten alle Aquarium Geräte mit Vorsicht gehandhabt werden. In keinem der unten aufgeführten Fälle sollte die Reparatur vom Kunden versucht werden. Das Gerät muss zu einem autorisierten Kundendienst gebracht werden. a.
Ein Gerät mit beschädigtem Kabel oder Stecker darf nicht in Betrieb genommen werden. Das gleiche gilt, wenn das Gerät nicht richtig funktioniert, fallen gelassen oder anderweitig beschädigt wurde. b.
Um ein Nasswerden des Gerätesteckers oder der Steckdose zu vermeiden, sollten der
Aquarium Unterschrank und das Becken seitlich von der Wandsteckdose aufgestellt werden.
Somit können keine Tropfen auf den Stecker oder die Steckdose fallen. Eine „Tropfenschleife“ sollte in jedem Kabel zwischen Aquarium und Steckdose vorgesehen werden. Die
„Tropfenschleife“ ist der Teil des Kabels, der unter der Steckdose durchhängt (Skizze 1). Auf diese Weise tropft das Wasser unter der Steckdose vom Kabel ab und kann nicht mit dieser in
Berührung kommen. Wenn der Stecker oder die Steckdose nass wird, NICHT das Kabel herausziehen, sondern die Stromversorgung an der Sicherung bzw. am Leistungsschalter trennen. Dann erst den Stecker herausziehen und prüfen, ob sich Wasser in der Steckdose befindet.
3) Kinder müssen beaufsichtigt werden, wenn Sie sich am Aquarium oder in dessen Nähe
Aufhalten.
4) Bei Nichtverwendung, vor dem Montieren/Demontieren von Teilen oder vor dem Reinigen müssen die betroffenen Geräte stets ausgesteckt werden. Nicht am Kabel ziehen. Zum
Herausziehen des Kabels immer den Stecker greifen.
5) Die Geräte dürfen nur für den vorgesehenen Zweck verwendet werden. Die Verwendung von
Zubehör, das vom Hersteller nicht empfohlen oder verkauft wird, kann gefährliche
Bedingungen verursachen.
6) Das Gerät nicht an einer Stelle installieren oder lagern, wo es der Witterung oder
Temperaturen unter null Grad ausgesetzt ist.
7) Das Gerät ist mit einem Schukostecker ausgestattet. Dieser Stecker darf auf keine Weise verändert oder umgangen werden.
Wird der Stecker entfernt erlischt jeder Garantieanspruch!
Diese Anleitung aufbewahren
-2-
Innenabschäumer SC 1350
Der Deltec Innenabschäumer ist für den Einsatz in Filterwannen vorgesehen.
Er zeichnet sich aus durch:
Präzisions- Wasserstandsregler
Schalldämpfer
Großen Schaumbecher
Hohe Leistung
Extrem niedriger Energieverbrauch
Leisen Betrieb
Einbau
Der Wasserstand in der Filterwanne sollte zwischen 150 - 250 mm sein. Die Vorraussetzung für einen einwandfreien und zuverlässigen Betrieb ist ein konstanter Wasserstand in der
Filterwanne (Zeichnung a). Dadurch, dass die Abschäumerpumpe Wasser aus der
Filterwanne mit einem bestimmten Niveau gegen die Wassersäule im Abschäumer pumpen muss, ändern sich die Pumpenwerte wie Luftleistung, Stromaufnahme, Durchflussmenge bei unterschiedlichen Wasserständen. Um jederzeit einen konstanten Wasserstand in der
Filterwanne zu garantieren, wird empfohlen, ein Nachfüllsystem wie den Deltec Aquastat
1001 oder ähnliches zu verwenden. Eine andere Möglichkeit ist der Einbau einer
Abschäumerkammer (Zeichnung b) in die Filterwanne, die einen höheren Wasserstandstand als die Filterwanne haben muss. Vom Aquairumüberlauf oder der Hauptpumpe kann diese
Abschäumerkammer über einen Bypass mit Wasser versorgt werden. Die Höhe der
Abschäumerkammer sollte zwischen 150 und 250 mm sein.
-3-
Inbetriebnahme
Nach dem Einbau sollte der Abschäumer wie folgt in Betreib genommen werden:
Niveauregler durch Drehen im Uhrzeigersinn ganz öffnen.
Wasserzufuhr für die Abschäumerkammer einschalten (falls vorhanden).
Niveauregler langsam schließen bis Schaum im unteren Bereich des Schaumtopfrohres sichtbar ist (Zeichnung c).
Um ein anfängliches Überschäumen zu vermeiden, die Schaumsäule mittels des
Niveaureglers zunächst eher niedriger einstellen
Die Schaumbildung nach der Inbetriebnahme beobachten und eventuell mit dem
Niveauregler korrigieren.
Eine endgültige Feineinstellung kann frühestens nach 24 Stunden vorgenommen werden.
Dazu wird mit dem Niveauregler das Schaumbild im Steigrohr so eingestellt, dass die feinen
Luftblasen leicht über dem Schaumtopfboden anfangen zu größeren Blasen zu zerplatzen
(Zeichnung d).
Für nassen Schaum (helle Flüssigkeit im Schaumtopf) den Niveauregler gegen den
Uhrzeigersinn drehen.
-
Für trockenen Schaum (dunkle Flüssigkeit im Schaumtopf) den Niveauregler im
Uhrzeigersinn drehen.
Wichtig: Die Pumpe niemals trocken laufen lassen.
-4-
d) Schaumtopf mit Übergangsrohr
Betrieb mit Ozon
Ozon ist ein extrem aggressives Gas, bei unsachgemäßem Gebrauch kann es zu gesundheitlichen Beeinträchtigungen kommen, deshalb darf Ozon niemals direkt einatmet werden. Zudem kann Ozon, bei zu hoher Dosierung, zu Schäden am Abschäumer führen.
Die Ozon Dosierung ist so einzustellen, dass kein freies Ozon am Deckel des Abschäumers wahrzunehmen ist. Die Deltec Abschäumer können mit max. 50 mg/Stunde Ozon pro
Pumpe betrieben werden. Dazu wird in den Luftschlauch oberhalb der der
Abschäumerpumpe ein ozonfestes T-Stück gesetzt. Das freie Ende des T-Stücks wird mit einem ozonfesten Schlauch mit dem Ozongerät verbunden. Über einen Lufthahn zwischen
T-Stück und Schalldämpfer die Luft soweit drosseln, bis Luft selbstständig durch das
Ozongerät angesaugt wird.
Sicherheitshinweise:
Die maximale Ozonmenge von 50mg/Stunde pro Pumpe darf nicht überschritten werden.
Durch Staubablagerungen im Ozongerät kann sich der Luftdurchlass verringern. Das kann zu einer Erhöhung des Wasserstandes im Abschäumer führen wodurch dieser im
Extremfall überlaufen kann. Um dies zu vermeiden ist das Ozongerät regelmäßig auf
Ablagerungen zu kontrollieren und ggf. zu reinigen.
Niemals freies Ozon einatmen.
Das Ozongerät darf nicht direkt an den Lufthahn bzw. den Schalldämpfer angeschlossen werden.
Zur Vermeidung von Wasserschäden muss das Ozongerät so hoch aufstellt werden, dass beim Abstellen der Abschäumerpumpe kein Wasser in das Gerät eindringen kann
Frisches Meerwasser
Durch bestimmte Zusätze in vielen Meersalzen erzeugt der Abschäumer extrem feine
Luftblasen, die nicht zurückgehalten werden können, gleichzeitig wird sehr wässeriger
-5-
Schaum erzeugt. Durch häufiges Entleeren des Schaumtopfes, können die besagten
Inhaltsstoffe im Aquariumwasser reduziert werden. Außerdem kann durch vorübergehendes stärkeres Füttern die extreme Feinblasenbildung vermindert werden.
Technische Daten
Technische
Daten mm
SC Serie Stellfläche Höhe
Hoher
Besatz
Liter
Normaler
Besatz
300 500 mm min. max.
Stromaufnahme
Watt
Luft
Liter/Std.
SC 1350 160x180 500 150 250 9 450
Fehlersuche
Symptom
Pumpe läuft, jedoch keine oder zu geringe Luftmenge
Ursache
Luftzuleitung zur Pumpe verstopft
Ozongerät verschmutzt
Luftschlauch abgeknickt
Luftansaugdüse verstopft
Schmutz im Laufrad
Maßnahme reinigen reinigen
Schlauchführung ändern reinigen reinigen
Andere Salze verwenden, mehr füttern
Kommt bei bestimmten Seesalzen und bei Zugabe von Wasseraufbereitungsmitteln vor Starke Luftperlung im Ablaufwasser
Pumpe läuft nicht an
Bei sehr starker Wasser-Belastung nach Neueinrichtung mit lebenden
Steinen
Wird die Pumpe (nach
Inbetriebnahme) trocken gelagert, kann das Lager in der vorderen
Lagerplatte eintrocknen.
Luftmenge stark drosseln
Laufeinheit wie nachstehend illustriert ausbauen und in
Leitungswasser durch axiale und radiale Bewegungen lösen
Laufeinheit falsch montiert Siehe Ein- Ausbau der Laufeinheit
Demontage der Pumpe: siehe Seite 27
Wartung
Bei korrektem Einbau und Einstellung benötigen Deltec Abschäumer denkbar wenig
Wartung. Durch Kalkwassermischer und Kalkreaktoren kann es jedoch zu Kalkablagerungen in der Pumpe kommen, die zu Funktionsstörungen führen können.
Es wird empfohlen bei Störungen oder alle 6 Monate den Rotor sowie die Strömungsklappe auf Leichtgängigkeit und die Lufteinzugsdüse auf freien Durchgang hin zu prüfen. Durch eintauchen der Teile in einen handelsüblichen Entkalker lösen sich die Kalkablagerungen.
Ein frühzeitiges Verstopfen der Lufteinzugsdüse durch Luftstaub und Salzkristalle kann durch ca. 15-30 minütiges Abstellen der Pumpe 1 mal pro Woche vermieden werden.
Zu beachten: Um einen störungsfreien Betrieb zu gewährleisten, ist es wichtig den
Niveauregler in regelmäßigen Abständen (min. einmal wöchentlich) auf Verunreinigungen zu kontrollieren und gegebenenfalls zu reinigen. Nach wiedereinsetzen des Niveaureglers ist der Wasserstand im Abschäumer zu kontrollieren und ggf. neu einzustellen.
Verunreinigungen und Ablagerungen können zur Erhöhung des Wasserstandes bis hin zum
Überlaufen des Abschäumers führen.
-6-
Ersatzteilliste SC 1350
Number Art. No. Description
81130000 SC 1350
A
1
2
28017000 Pumpe komplett
81130100 Körper mit Wasserstandsregler
88020200 Schaumtopf
Number Art. No. Description
8 81140400 Pumpengehäuse DCS 400
9
10
11
26017000 Stator DCS 400
27017000 Laufeinheit DCS 400
81140500 Wasserstandsregler Teil 1
3
4
5
6
7
80500075 O-Ring Schaumtopf
81140300 Deckel Schaumtopf
64059000 Schalldämpfer
61758000 Silikonschlauch weiß 5/8
81130700 Lufteinzugsdüse SC1350
12
13
14
81140600 Wasserstandsregler Teil 2
25094000 Silikon Fuß
12359000 Rändelschraube
-7-
IMPORTNT SAFETY INSTRUCTIONS
WARNING To guard against injury, basic safety precautions should be observed, including the following.
1)
2)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
DANGER – To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance. a) b)
Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner.
To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug.
A “drip-loop”, shown in the figure below, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The “drip-loop” is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water travelling along the cord and coming in contact with the receptacle.
If the plug or socket does get wet, DON´T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug and examine for presence of water in the receptacle.
3)
4)
Close supervision is necessary when any appliance is used by or near children.
Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.
5)
6)
Make sure an appliance mounted on a tank is securely installed before operating it.
Read and observe all the important notices on the appliance.
7) If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should bee taken to arrange the cord so that it will not be tripped over or pulled.
8) This appliance has a polarized plug (one blade is wider than the other). As safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.
Exception: This instruction may be omitted for an appliance that is not provided with a polarized attachment plug.
Removing of the plug invalidates the warranty!
SAVE THESE INSTRUCTIONS
-8-
Internal protein Skimmer SC 1350
Deltec ”SC“ series protein Skimmer are very compact, highly efficient and are fitted with a special low energy skimmer pump.
The “SC” skimmers features
precision water level adjuster
silencer
designed to operate in external filter sumps (diagram a)
large volume Skimmer cup
quiet operation
Installation
For best performance the water level in the filter sump should be between 150 and
250 mm. A prerequisite for continuous efficient performance is a constant water level in which the skimmer operates. Ideally, a water level top up system should be used such as the Deltec Aquastat 1001 or better still, a separate skimmer compartment in the sump
(diagram b). The water level in the skimmer compartment should be higher than in the rest of the sump, but within the levels recommended for the skimmer model.
This compartment can be supplied with water from a bypass of the aquarium overflow.
-9-
Starting the skimmer
position the skimmer in the sump
feed water into the skimmer compartment (if applicable)
open the water level adjuster fully by turning it clockwise
start the skimmer pump
turn the water level adjuster anti-clockwise until fine bubbles are visible between the bayonet and the bottom of the skimmer cup (diagram c)
initially keep the foam level in the skimmer cup low to avoid over skimming and possible flooding of the cup
wait a minimum of 24 hours before the final adjustment
turn the water level adjuster in or out until the fine air bubbles start bursting approximately half way up the cups riser tube
for dry foam turn the water level adjuster clockwise
for wet foam anti-clockwise
Important: Never allow the pump to run dry.
-10-
Operation with ozone
Ozone is an extremely aggressive gas which - if not used properly - can damage one's health. For this reason, ozone should never be breathed in directly.
In addition, at high doses ozone can damage the skimmer.
The dosing of ozone must be set so that no free ozone can be detected at the skimmer lid.
Deltec skimmers can be operated with 50 mg/h of ozone per pump. An ozone-resistant Tpiece should be fitted in the air hose above the skimmer pump. The free end of the T-piece is connected to the ozonizer by means of an ozone-resistant hose. Use an air tap below the silencer to regulate the air flow through the ozonizer.
The air is automatically sucked into the ozoniser by the skimmer pump. Should the skimmer performance deteriorate please check the ozoniser for blockage.
Safety information:
The maximum ozone quantity of 50mg/hour per pump must not be exceeded.
The air passage can be reduced as a result of dust deposits in the ozonizer. This can result in an increase in the water level in the skimmer, which - in extreme cases - can overflow. To avoid this, check the ozonizer regularly to make sure that there are no deposits of dust. If necessary, clean the ozonizer.
Never breathe in free ozone.
In order to avoid water damage, the ozonizer must be placed above the skinner, high enough to ensure that no water can enter it when the skimmer pump is switched off.
c) Skimmer cup
-11-
Fresh salt water
If the skimmer is used with new water on an aquarium it is common to find an excessive quantity of small bubbles and often the skimmer cup fills with a clear liquid. This is due to the high surface tension of the new water which prevents the bubbles from bursting. Once the water matures this effect will go away but can take up to 2-3 weeks. The effect is different on different salt brands and is often dependant on levels of conditioning agents added to the salt. Once these are skimmed out, then the skimmer will act normally.
Heavier feeding in the initial stages will give the chemically pure water something to react with and allow it to mature into proper aquarium salt water rather than the initial chemical soup which is new salt water.
Technical data
technical data
SC Serie
Dimensions mm
Footprint height litre high stocking normal stocking mm min. max.
Power consumption
Watt
Air litre/h max.
SC 1350 160x180 500 300 500 150 250 9 450
* it is best to chose the max. water level
Fault finding
malfunction
Pump produces insufficient air
Cause airline or venturi blocked airline kinked ozonizer blocked remedy clean remove kink clean excessive air bubbles in aquarium water
Dirt in pinwheel caused by additives in certain sea salts and water conditioners clean
Use different salt or feed heavily for a period, empty skimmer cup frequently. This condition may last for several weeks.
Pump does not start
Bearing of the impeller stuck. When the pump (after having been used) has been stored dry for a period of time, the bearing can "dry out".
Remove impeller and soak it in tap water or vinegar.
Disassembly of the pump: see page 27
Maintenance
The Deltec skimmer range should need very little adjustment and maintenance once set correctly however due to the high levels of calcium in marine aquariums it is common for deposits to build up on moving parts requiring periodical cleaning. It is recommended every
6 months, or when required, that the pumps are removed from the skimmer having first drained the body of Water.
Check and clean the impellor of debris. A build up of calcium, dust and salt can restrict or block the venturi inlet on the connecting pipe work and reduce the skimming efficiency. This should be checked and carefully cleaned with a toothpick or fine drill rotated between the fingertips.
It is advisable to stop the pump for approximately 15 minutes once every week in order to dissolve any dust or salt crystals that may have collected in the venturi tube.
-12-
Spare part list SC 1350
Number Art. No. Description
81130000 SC 1350
A
1
28017000 Pump complete
81130100 Body incl. water level adjuster
2
3
4
5
6
7
88020200 Skimmer cup
80500075 O-Ring skimmer cup
81140300 Skimmer cup lid
64059000 Silencer
61758000 Silicone hose white 5/8
81130700 Air inlet adapter SC1350
Number Art. No. Description
8 81140400 Pump housing DCS 400
9
10
26017000 Stator DCS 400
27017000 Impeller DCS 400
11
12
13
14
81140500 Water level adjuster part 1
81140600 Water level adjuster part 2
25094000 Silicone foot
12359000 Knurled-head screw
-13-
NORME DI SICUREZZA
AVVERTENZA: Per evitare incidenti si raccomanda di osservare le norme generali di sicurezza, tra cui le seguenti:
1) LEGGERE E SEGUIRE SCRUPOLOSAMENTE TUTTE LE NORME DI SICUREZZA.
2) PERICOLO – Considerato che l’uso di attrezzature per acquario avviene in presenza di acqua, agire sempre con particolare cautela per evitare scosse elettriche. Per ognuna delle seguenti situazioni possibili, si raccomanda di non tentare di eseguire da sé eventuali riparazioni, ma di portare l’apparecchio presso un centro assistenza autorizzato o provvedere alla sua rottamazione. a.
Non mettere in funzione l’apparecchio se il cavo d’alimentazione o la spina appaiono danneggiati, se l’apparecchio è malfunzionante, se è caduto o ha subito un qualsiasi danno. b.
Per evitare il gocciolamento dell’acqua sulla presa o sulla spina, posizionare l’acquario e il mobile di fianco alla presa montata a parete in modo che questa resti visibile.
Si raccomanda di fare eseguire al cavo una curva “anti-gocciolamento” come mostrato nella figura sottostante. Eseguire l’operazione per tutti i componenti elettrici dell’acquario. In questo modo una parte di cavo si trova sotto il livello della presa, o della spina di collegamento nel caso si usi una prolunga, impedendo così che l’acqua gocciolando lungo il cavo venga a contatto con la presa.
Se la presa o la spina si bagna, NON disinserire il cavo, ma scollegare l’interruttore generale che porta corrente all’apparecchio. Quindi scollegare la spina e verificare la presenza di acqua all’interno della presa.
3) Se l’apparecchio viene utilizzato da o in presenza di bambini, è necessaria un’attenta supervisione da parte degli adulti.
4) In caso di non utilizzo, prima del montaggio/smontaggio di parti o prima di ogni pulizia, scollegare l’apparecchio dalla rete d’alimentazione. Scollegare afferrando bene la spina e senza tirare il cavo d’alimentazione.
5) Non utilizzare l’apparecchio per usi diversi da quelli a cui è destinato. L’uso di accessori non raccomandati o non venduti dal produttore dell’apparecchio possono essere causa di condizioni di funzionamento non sicure.
6) Non installare o immagazzinare l’apparecchio in luoghi esposti alle intemperie o a temperature sotto 0°C.
7) Leggere ed osservare tutte le informazioni importanti sull’apparecchio.
8) Se è necessario l’uso di una prolunga, assicurarsi che il cavo sia adatto al voltaggio utilizzato.
Se il cavo è messo a punto per meno ampere or watt rispetto all’apparecchio, potrebbe surriscaldarsi. Fare attenzione che il cavo non sia troppo teso o schiacciato.
9) L’apparecchio è dotato di spina Schuko, che per nessun motivo deve essere modificata o manomessa.
In caso di manomissione della spina decade ogni garanzia!
“CONSERVATE LE PRESENTI ISTRUZIONI”
-14-
Schiumatoio interno SC 1350
Deltec SC 1350, destinato all’installazione in una sump esterna (disegno a), è uno schiumatoio compatto e molto efficiente, con le seguenti caratteristiche principali:
- regolatore di livello di precisione
- dotato di silenziatore
- bicchiere con elevata capacità
- alta resa
- pompa a minimo consumo energetico
- funzionamento silenzioso
Installazione
Per una resa ottimale il livello dell’acqua nella sump deve essere tra 150 e 250 mm. Il mantenimento di un livello costante dell’acqua nella sump è quindi un requisito importante per il funzionamento continuo ed affidabile dell’apparecchio.
I dati relativi alla pompa (come resa, consumo, quantità di flusso) variano secondo il livello dell’acqua (vedi dati tecnici), proprio perché la pompa dello schiumatoio deve prelevare acqua dalla sump ad un determinato livello per portarla verso la colonna nello schiumatoio.
Per garantire un livello costante nella sump, si consiglia l’uso di un sistema di rabbocco, come ad es. il Deltec Aquastat 1001.
Ancora meglio è prevedere nella sump una camera di schiumazione (disegno b) che abbia un livello d’acqua superiore a quello della sump stessa (ma pur sempre nei limiti raccomandati dal modello di schiumatoio) e che sia alimentata dalla tracimazione dell’acquario tramite un bypass.
-15-
Messa in funzione
Dopo l’installazione procedere alla messa in funzione come segue:
Posizionare lo schiumatoio nella sump.
Aprire completamente il regolatore di livello ruotando in senso orario.
Far entrare l’acqua nella camera di schiumazione (se presente).
Avviare la pompa dello schiumatoio.
Impostare il regolatore di livello chiudendolo fino a quando le bolle fini siano visibili tra l’attacco a bajonetta e il fondo del bicchiere (disegno c).
Inizialmente mantenere basso il livello di schiuma nel bicchiere per evitare una schiumazione eccessiva e fuoriuscite.
Osservare la formazione di schiuma dopo la messa in funzione ed eventualmente correggerla tramite il regolatore di livello.
- Attendere almeno 24 ore prima della regolazione finale.
- Ruotare il regolatore di livello in senso orario o antiorario fino a quando la schiuma più fine andrà a sostituire quella formata da bolle più grosse nella parte media della colonna del bicchiere.
Per una schiuma bagnata (liquido chiaro nel bicchiere) ruotare il regolatore di livello in senso antiorario.
-
Per una schiuma asciutta (liquido scuro nel bicchiere) ruotare il regolatore di livello in senso orario.
Importante: Non fare mai funzionare la pompa a secco.
-16-
Funzionamento con ozono
L’ozono è un gas estremamente aggressivo, se utilizzato in modo improprio può compromettere la salute, pertanto non il gas non deve mai essere inalato direttamente.
Inoltre, se utilizzato in dosaggio elevato, l’ozono può danneggiare anche lo schiumatoio.
Il dosaggio dell’ozono si deve impostare in modo che non si percepisca la presenza di ozono libero sul coperchio dello schiumatoio. Gli schiumatoi Deltec si possono utilizzare con dosaggi di ozono max. 50 mg/ora per pompa. A tale scopo viene inserito un raccordo a T resistente all’ozono nel tubo dell’aria sopra la pompa dello schiumatoio. L’estremità libera del raccordo a T viene collegata all’ozonizzatore mediante un tubo flessibile resistente all’ozono. Usare il rubinetto dell’aria sotto il silenziatore per regolare il flusso d’aria che passa nell’ozonizzatore.
L’aria viene aspirata automaticamente nell’ozonizzatore dalla pompa dello schiumatoio. Se la resa diminuisce, controllare che l’ozonizzatore non sia bloccato.
Avvertenze sulla sicurezza:
Non superare la quantità massima di ozono di 50 mg/ora per pompa.
Il passaggio dell’aria può restringersi a causa dei depositi di polvere nell’ozonizzatore.
Ciò può provocare l’aumento del livello dell'acqua nello schiumatoio per cui, in casi estremi, questo può tracimare. Per impedire ciò, si deve controllare regolarmente l’ozonizzatore per accertare la presenza di depositi ed eventualmente pulirlo.
Non respirare mai l’ozono libero.
Non collegare l’ozonizzatore direttamente al rubinetto dell’aria.
Per impedire danni provocati dall’acqua, l’ozonizzatore deve essere posizionato ad un’altezza tale che, in caso di spegnimento della pompa dello schiumatoio, non possa penetrare acqua nell’apparecchio.
Fondo del bicchiere
Attacco a bajonetta c) Bicchiere dello schiumatoio
-17-
Acqua marina nuova
Se lo schiumatoio viene utilizzato in un acquario allestito da poco è normale osservare una produzione eccessiva di schiuma fine che presto riempie il bicchiere di liquido chiaro. Questo
è dovuto alla forte tensione superficiale dell’acqua nuova che impedisce alle bolle di scoppiare. Una volta che l’acqua matura, questo inconveniente sparisce, ma possono essere necessarie due o tre settimane. L’effetto è diverso in base al tipo/marca di sale utilizzato e spesso dipende dai livelli di agenti condizionanti addizionati ai sali. Tali sostanze vengono man mano ridotte attraverso un frequente svuotamento del bicchiere. Inoltre una somministrazione di cibo un po’ abbondante all’inizio può accelerare la maturazione dell’acqua marina e limitare la formazione di schiuma fine.
Dati tecnici
Dati tecnici
Serie SC mm
Base Altezza litri
Densità alta
Densità normale
* min. max.
Consumo energetico
Watt
Aria litri/h max.
SC 1350 160x180 500 300 500 150 250
* si consiglia di scegliere il livello massimo.
Ricerca errori
Inconveniente
La pompa funziona, ma la quantità di aria è nulla o insufficiente
Bolle d’aria in eccesso nell’acqua dell’acquario
La pompa non parte
9 450
Causa Rimedio
La tubazione dell’aria è ostruita Effettuare pulizia
L’ozonizzatore è bloccato
Il tubo dell’aria è schiacciato
Effettuare pulizia
Modificare il percorso del tubo
L’ugello che aspira aria è ostruito Effettuare pulizia
Elementi della pompa sono bloccati
Si verifica con l’uso di certi sali o di prodotti per il trattamento dell’acqua
Effettuare pulizia
Cambiare sale ed aumentare temporaneamente la quantità di cibo. Svuotare frequentemente il bicchiere. La situazione può perdurare per diverse settimane.
Ridurre di molto la quantità di aria Può verificarsi in caso di acqua molto inquinata dopo nuovo allestimento con rocce vive
Cuscinetto della girante bloccato.
Se la pompa rimane inutilizzata a lungo, il cuscinetto anteriore della girante può seccarsi e bloccarsi.
Smontare la girante con l’apposito estrattore, come di seguito descritto ed eliminare il blocco in acqua corrente muovendo il cuscinetto lungo e attorno all’alberino di ceramica.
Ridurre di molto la quantità di aria Può verificarsi in caso di acqua molto inquinata dopo nuovo allestimento con rocce vive
-18-
Smontaggio pompa: vedere pag. 27
Manutenzione
Se installato ed impostato correttamente, lo schiumatoio Detec SC necessita di pochissima manutenzione. Tuttavia, l’uso di reattori di calcio e miscelatori di kalkwasser può determinare la formazione di depositi calcarei nella pompa che possono pregiudicare il buon funzionamento. Si consiglia quindi, all’occorrenza oppure ogni 6 mesi, di verificare il libero movimento del rotore e delle alette all’interno della pompa, nonché il tubo venturi per l’entrata dell’aria. Dopo avere svuotato il corpo dell’apparecchio dall’acqua, controllare e pulire la girante. Assicurarsi che le alette di direzione si muovano liberamente e se necessario immergere le parti in acqua e aceto o altra soluzione anticalcare per eliminare le incrostazioni. Il deposito di calcare, polvere e sali può restringere o bloccare l’entrata del venturi e ridurre l’efficienza dello schiumatoio. Per questo è necessario verificare ed eventualmente pulire l’ugello con un stuzzicadenti fatto ruotare tra le dita. L’ostruzione del venturi ad opera di polvere o cristalli di sale può essere evitata fermando la pompa per ca.
15-30 minuti 1 volta alla settimana.
Nota: per garantire un corretto funzionamento, è importante ispezionare ed eventualmente pulire il regolatore di livello ad intervalli regolari (almeno una volta alla settimana). Per eseguire il controllo, estrarre il regolatore di livello verso l’alto. Una volta riposizionato il regolatore di livello nella sua sede, è necessario controllare ed eventualmente reimpostare il livello dell’acqua nello schiumatoio. Questa operazione è importante, in quanto incrostazioni e depositi possono causare un aumento del livello dell’acqua fino alla tracimazione.
-19-
Elenco ricambi SC 1350
Rif.
A
5
6
7
1
2
3
4
Art. N. Descrizione
81130000 SC 1350
28017000 Pompa completa
Apparecchio base incl.
81130100 regolatore di livello
88020200 Bicchiere
80500075 O-Ring bicchiere
81140300 Coperchio bicchiere
64059000 Silenziatore
61758000 Tubo silicone bianco 5/8
81130700 Ugello aspirazione aria SC1350
-20-
Rif.
8
9
10
11
12
13
14
Art. N. Descrizione
81140400 Corpo pompa DCS 400
26017000 Statore DCS 400
27017000 Girante DCS 400
81140500 Regolatore livello parte 1
81140600 Regolatore livello parte 2
25094000 Piede in silicone
12359000 Vite rosso
Instructions de sécurité importantes
Avertissement : Pour protéger contre quelconques blessures, il faut respecter les mesures de prudence et les instructions de sécurité suivantes :
1) Lire et respecter les instructions de sécurité.
2) Danger : Pour éviter une électrocution, il faut manipuler tous les appareils de l'aquarium avec prudence. Dans aucun des cas indiqué plus bas, le client ne devrait pas essayer de procéder à une réparation. L’appareil doit être délivré au service après-vente autorisé. c.
Si vous observez une fuite d'eau anormale sur l'appareil, il faut retirer immédiatement la prise de l’appareil. b) Après l'installation, il faut vérifier soigneusement l'appareil. Il ne faut pas enficher sa prise quand de l'eau se trouve sur des pièces qui doivent rester sèches. c) Un appareil muni d’un câble ou d’une fiche détériorés ne doit pas être mis en service. Ceci est aussi valable quand l’appareil ne fonctionne pas correctement, est tombé par terre ou a été détérioré d’une autre manière. d) Pour éviter que la fiche de l'appareil ou la prise de courant se mouille, il faut placer le meuble de l’aquarium et le bassin à côté de la prise de courant murale. Ainsi aucune goutte d'eau ne tombera sur la fiche ou la prise de courant. Une « boucle d’égouttage » devrait être prévue entre l'aquarium et la prise de courant murale. La « boucle d’égouttage » est la partie du câble qui fléchit sous la prise de courant en cas d’emploi d’une rallonge. De cette manière, l'eau s'égouttera sous la prise de courant du câble et ne pourra pas entrer en contact avec celui-ci. Si la fiche ou la prise de courant se mouille, NE
PAS retirer le câble mais couper l’alimentation en courant au fusible ou au sectionneur de puissance.
Ne retirer la fiche qu’après avoir ceci et vérifier si de l'eau se trouve dans la prise de courant.
3) Les enfants doivent être surveillés quand vous vous occupez de l'aquarium ou vous vous trouvez à proximité.
4) Pour éviter quelconques blessures, ne pas toucher les pièces mobiles ou chaudes, telles que les chauffages, les réflecteurs, les ampoules etc.
5) Les fiche des appareils qui ne sont pas utilisés, avant le montage/démontage de pièces de ces appareils ou avant leur nettoyage, doivent être retirées. Ne pas tirer au câble. Pour sortir le câble, toujours saisir la fiche.
6) Les appareils ne doivent être utilisés qu'aux fins prévues. L’emploi d’accessoires que le fabricant n'a pas recommandés ou vendus, peut causer des conditions dangereuses.
7) Ne pas installer ou entreposer l’appareil à un endroit où il est exposé aux intempéries ou à des températures en dessous de zéro.
8) Avant la mise en service d’un appareil monté à la paroi du bassin, il faut garantir que cet appareil est correctement installé et fixé.
9) Toutes les indications de sécurité sur l'appareil doivent être lues.
10) S'il faut utiliser une rallonge, elle doit avoir la puissance nécessaire. Un câble qui est homologué pour peu d’ampères ou de watts, peut se surchauffer. Le câble doit être posé de sorte que personne ne trébuche dessus ou y reste accroché.
11) L’appareil est équipé d’une fiche à contact de protection. Cette fiche ne doit en aucun cas être modifiée ou contournée.
Si la fiche est retirée, tout droit à garantie sera annulé !
Conserver ces instructions
-21-
Ecumeur à protéines interne SC 1350
Les écumeurs Deltec de la série « SC » sont des appareils très compacts, très performants et équipés d’une pompe spéciale à faible consommation.
La série “SC” intègre
Vanne de précision pour le réglage du niveau d’eau
Silencieux
Etudié pour un fonctionnement dans des décantations (diagramme a)
Godet de réception d’écume d’un grand volume
Fonctionnement silencieux
Installation
Pour des performances optimales, le niveau d’eau de la décantation doit être de 150 à
250mm. Une condition préalable au bon fonctionnement est d’assurer un niveau stable à l’endroit où l’écumeur devra être placé. Idéalement, un système de remise à niveau automatique devrait être utilisé, comme par ex. le Deltec « Aquastat 1001 », ou encore mieux, par l’utilisation d’un compartiment dédié pour l’écumeur (diagramme b). Le niveau d’eau dans le compartiment de l’écumeur doit être plus élevé que le reste de la décantation, mais dans les limites recommandées pour le modèle de l’écumeur.
Ce compartiment pourra être alimenté en eau par un “bypass” du trop-plein de l’aquarium.
-22-
Démarrage de l’écumeur
Placez l’écumeur dans la décantation
Alimentez le compartiment de l’écumeur (si nécessaire)
Ouvrez le réglage de niveau d’eau totalement en tournant dans le sens antihorlogique
Branchez la pompe
Ajustez le réglage de niveau d’eau en tournant dans le sens anti-horlogique jusqu’à ce que de fines bulles soient visibles entre la fermeture “baïonnette” et la base du godet de l’écumeur (diagramme c)
Au départ, gardez le niveau de mousse dans l’écumeur assez bas afin d’éviter un sur-
écumage et un débordement du godet
Attendez au min. 24 heures avant de faire l’ajustement final
Tournez l’ajusteur niveau d’eau jusqu’à ce que des fines bulles d’air commencent à
éclater approximativement au milieu du tube réacteur dans le godet
-
Pour une écume plus sèche, régler le niveau d’eau dans le sens anti-horlogique, pour une écume humide, dans le sens horlogique.
- Important: Ne jamais laisser fonctionner la pompe à sec.
-23-
Fonctionnement avec de l’Ozone
L’Ozone est un gaz extrêmement agressif, qui, s’il n’est pas utilisé correctement, peut causer des dommages pour la santé. Pour cette raison, l’Ozone ne devrait jamais être respiré directement.
De plus, à haute concentration, l’Ozone pourrait endommager l’écumeur.
Le dosage de l’Ozone devrait être réglé afin qu’aucun Ozone libre ne puisse être perçu hors du couvercle de l’écumeur. Les écumeurs Deltec peuvent fonctionner à 50 mg/heure d’Ozone par pompe. Un « T » résistant à l’Ozone doit être placé sur le tuyau d’air au-dessus du pot de l’écumeur. La partie libre de ce « T » est connectée à l’Ozonisateur grâce à un tuyau résistant à l’Ozone. Utilisez un robinet d’air sous le silencieux afin de régler débit d’air dans l’Ozonisateur.
L’air est automatiquement aspiré dans l’Ozonisateur par la pompe de l’écumeur. Si les performances de l’écumeur se déteriorent, vérifiez l’Ozonisateur pour éviter les bloquages.
Information de sécurité:
La dose max. d’Ozone de 50mg/heure par pompe ne peut être dépassée.
Le passage d’air ne doit pas être réduit sous peine d’accumulation de poussières dans l’Ozonisateur. Cela pourrait conduire à une augmentation du niveau d’eau dans l’écumeur, et, dans des cas extrêmes, à un débordement. Pour éviter ceci, vérifiez régulièrement l’Ozonisateur pour vous assurer qu’il n’y a pas d’accumulation de poussières. Si nécessaire, nettoyez-le.
Ne respirez jamais l’Ozone libre.
-
Afin d’éviter tout dégât des eaux, l’Ozonisateur doit être placé au-dessus de l’écumeur, suffisamment haut afin d’empêcher l’eau de pénétrer dans celui-ci lorsque la pompe de l’écumeur est éteinte
c) Godet de l’écumeur
-24-
Eau de mer fraîche
Si l’écumeur est utilisé avec de l’eau neuve, il est courant de constater une quantité excessive de petites bulles produites et dès lors un remplissage rapide du pot de l’écumeur avec de l’eau claire. Cela est dû à la tension superficielle de l’eau neuve très importante empêchant les bulles d’éclater. Après maturation de l’eau, ce symptôme disparaitra après 2
à 3 semaines. Cet effet peut être différent selon les marques de sel et est souvent dû à la quantité d’agent de conservation ajouté au sel. Une fois ces substances écumées, l’écumeur fonctionnera à nouveau parfaitement.
Un nourrissage abondant dans cette étape initiale apportera à l’eau pure chimiquement, des
éléments pour la « vieillir » plus rapidement vers un aquarium mature plutôt que de rester cette « soupe » chimique qu’est l’eau de mer artificielle neuve.
Données techniques
Données techniques série SC mm
Base Haut.
Très peuplé
Norm. peuplé requis* mm min. max.
Conso. électrique
Watt
Air litre/h max.
SC 1350 160x180 500 300 500 150 250 9 450
*il est preferable de choisir le niveau d’eau max.
Mauvais fonctionnement
Problème
Pompe produit trop peu d’air
Cause
Robinet, ligne d’air ou venturi bouché
Ligne d’air pincée
Ozonisateur bouché
Le clapet de la pompe bloqué
Remède
Nettoyer
Denouer
Déboucher
Nettoyer (voir 10a)
Trop de bulles d’air dans l’aquarium
Causé par des additifs de certains sels ou à la qualité de l’eau
Utilisez une autre marque de sel ou nourrissez abondamment un certain temps, videz régulièrement le godet, ouvrez le
Le robinet d’air est trop fermé
La pompe ne démarre pas robinet d’air complètement. Cet état peut durer plusieurs semaines.
L’ouvrir plus fort
Le palier de la pompe est bloqué.
Quand la pompe (après avoir été utilisée) a été stockée à sec durant
Retirer le rotor et détartrer le avec du vinaigre une longue période, le palier peut
être sec
Maintenance
La gamme d’écumeurs Deltec ne nécessite que très peu de réglages et d’entretien une fois la mise en route effectuée correctement. Néanmoins, en raison de la teneur importante de calcium dans les aquariums marins, il est courant de constater des accumulations de dépôts sur les parties en mouvement ce qui impose un nettoyage périodique. Il est recommandé de procéder au démontage et nettoyage tous les 6 mois ou plus régulièrement en cas de besoin (vider l’écumeur au préalable).
Vérifiez et nettoyez le rotor de toute impureté. Assurez-vous que le clapet de direction bouge aisément et, si nécessaire, détartrez-le à l’aide de vinaigre blanc ou d’acide organique afin d’éliminer tout résidu calcaire. Une accumulation de calcaire, de saleté et de
-25-
sel peut boucher l’entrée du venturi sur le tuyau de connexion et réduire l’efficacité de l’écumage. Ceci doit être vérifié régulièrement et parfaitement nettoyé à l’aide d’un curedents ou d’une petite mèche tournée délicatement entre les doigts.
Il est également possible d’arrêter la pompe pendant 15 minutes toutes les semaines afin de permettre la dissolution des cristaux de sel accumulés dans le tuyau du venturi.
Liste pièces détachées SC 1350
Nombre Art. No. Description
A
81130000 SC 1350
28017000 Pompe complète
1
2
3
4
5
81130100 Corps avec régulateur niv. Eau
88020200 Godet écumeur
80500075 O-Ring godet
81140300 Couvercle godet
64059000 Silencieux
Nombre Art. No. Description
8
9
81140400 Carter pompe DCS 400
26017000 Moteur DCS 400
10
11
12
13
14
27017000 Rotor DCS 400
81140500 Régulateur niv. Eau part 1
81140600 Régulateur niv part 2
25094000 Pieds silicone
12359000 Vis papillon
-26-
Disassembly of the pump – Smontaggio pompa
1) 2) 3)
4) 5) 6) Assembly of the pump
Montaggio pompa
Montage de la pumpe
-27-
Deltec GmbH
Steller Straße 75
D-27755 Delmenhorst
Deutschland / Germany www.deltec-aquaristic.com
Deltec GmbH 12/2012

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Precision water level controller ensures consistent performance regardless of water level in the filter vat.
- Silencer reduces operating noise.
- Large foam cup collects more skimmate, reducing the need for frequent emptying.
- High performance removes a significant amount of organic waste from the water.
- Extremely low energy consumption saves on operating costs.
- Quiet operation minimizes noise pollution in the aquarium room.