TK-N1100 CCTV Camera Instruction Manual

TK-N1100 CCTV Camera Instruction Manual
INSTRUCTIONS
УС
TK-N1100
COLOR VIDEO CAMERA HEAD
BEDIENUNGSANLEITUNG: FARB-VIDEOKAMERAKOPF
MANUEL D'INSTRUCTIONS: TETE DE CAMERA VIDEO COULEUR
For Customer Use:
Enter below the Modei No and the
Serial No. which 1s located on the
bottom of the camera. Retain this
information for future reference.
FL
Model No.
SerialNo. N
FOR U Type Information for USA
This device complies with Part 15 of the FCC Rules.
CAUTION Changes or modifications not approved by the original
manufacture could void the user's authority to operate the
equipment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. INFORMATION (FOR CANADA)
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This digital apparatus does not exceed the Class B limits
for radio noise emissions from digital apparatus as set out
The lightning flash with arrowhead symbol, within an in the interferencecausing equipment standard entitled
equilateral triangle, is intended to alert the user to the “Digital Apparatus”, ICES-003 of the Department of
presence of uninsulated “dangerous voltage” within the Communications.
product's enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is Due to design modification, data given in this instruction
intended to alert the user to the presence of important book are subject to possible change without prior notice.
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
Models TK-N1100U (NTSC version) and TK-N1100E (PAL version) are
shown as U type (NTSC) and E type (PAL), respectively, in this manual.
Thank you for purchasing a color video camera head.
To gain maximum benefit from the camera, it is suggested that
you study this booklet carefully. After reading, retain it for future
reference.
FEATURES
e With 2 built-in CCDs (for black/white and color) and infrared ilumination,
continuous shooting during the day and night is possible. Switching
between the color mode for day and black-and-white mode for night
is automatic. At night, even under 0 Ix, you can shoot thanks to the
built-in infrared illumination. |
e 1/3inch410,000-pixei: U type, 470,000-pixel: E type (approx. 380,000
pixels effective: U type, 440,000 pixels effective: E type) CCD (Charge
Coupled Device) solid-state pickup element for clear pictures without
image lag or geometrical distortion.
High-resolution, high-sensitivity design for a horizontal resolu-
tion of 470 TV lines: U type, 460 TV lines: E type and a low-light
sensitivity of 2 Ix (F1.2) (Color mode)
eo TTL (Through-The-Lens) auto racking white balance adjust-
ment with preset luminous intensity (:0:) and manual override
(2 axes; G-Mg and R-B)
e Built-in electronic shutter to allow switching to 9 shutter speeds.
® АСС (Automatic Gain Control) function to automatically
increase camera’s sensitivity when the level of ambient light
drops.
PRECAUTIONS
SAFETY PRECAUTIONS
e Do not modify the unit or operate it without cover panel to pre-
vent danger.
e When there is any abnormality (abnormal noise, smell, smoke,
etc.) with the unit, immediately turn the power off and contact
your nearest JVC-authorized service agent.
CONTROLS AND THEIR LOCATIONS
Side view
es oo
B—
4 Bottom view
* Do not damage or fray the power cord. Otherwise, this will
cause leakage or electrical shock.
* If there is a danger of being struck by lightning during outdoor
| shooting, evacuate to a safe place immediately.
HANDLING PRECAUTIONS
e When setting up your monitor, be sure to avoid places subject to any
of the following conditions:
¢ Rain or excessive moisture
* Temperatures exceeding or falling below the recommended operating
temperatures.
—10°C to +50°C (operation)
0°C to +40°C (recommended)
* Radiation or X-rays and strong electromagnetic waves or magnetism.
Vibrations
* Dust, oil or gas
Cleaning the body: Wipe body with a dry, soft cloth (such as
cheesecloth). When it is extremely dirty, soak the cloth in a
solution of neutral detergent, wring it out and then wipe.
To prevent deformation of the body, etc., and to avoid operation
hazards, do not allow volatile liquids such as benzine and thin-
ner to touch the body, and do not wipe it with a cloth soaked in
such a liquid.
If the equipment is soiled with water, oil, solvent, etc., wipe over
with soft cloth or cotton first, then clean with gauze, etc., soaked
in denatured alcohol.
When shooting outdoors at night, it may not always be possible to
obtain sufficient object illumination with the built-in infrared light
illumination (LED) alone. In this case, install an external infrared light
source.
Because camera functioning is based on infrared ray reception in the
B/W mode, using a zoom lens when shooting in the B/W mode may
cause the lens to go out of focus. This is not a malfunction. To avoid
this, focus the lens manually or use a fixed-focus lens.
This unit uses the C-mount lens only. So be sure not to use the CS
mount lens.
Lens mount
This is the mount for installing the C-mount lens
See page 8 for a list of mountable lenses.
FOCUS/LOCK screw
A screw is provided to adjust and fix the Back Focus. See page 9.
Screw holes for camera installation (upper and lower sides)
Use the 1/4 inch-20UNC screw hole when installing the camera on a
tripod or a fixer, etc.
E SYNC IN connector
e BNC connector for external reference sync signal input such as
composite video signal (VBS) or black burst signal (BB).
e When the reference sync signal is input, the camera automatically
switches from the internal to external sync mode to perform gen-
lock operation.
Note:
If the input external reference sync signal is less than 65% below the
reference level, the external sync becomes unstable.
VIDEO OUT connector
BNC connector that outputs a composite video signal. Connect to
the video input connector of a monitor, switcher, etc.
В с - в/м
Color < black/white timing switch
If the color signal’s video level drops below the preset level because
of low illumination, this switch automatically changes to the B/W
position.
L: About 0.3 Y (p-p) color video level
H : About 0.5 V (p-p) color video level
When the color video level falls below these values, the unit switches
to the B/W mode. (With AGC switch “ON”)
Factory-preset value : L
infrared illumination (LED) switch
AUTO: LED is off in the color mode and lights up automatically in
the B/W mode.
OFF: LED is off at all times.
Factory preset : AUTO
EJ Infrared illumination (LED)
This lights automatically when the B/W mode is set (with lll Infrared
illumination (LED) switch : AUTO).
Install the camera so that the front luminescent window is displayed.
Note:
Install an external infrared light source when object illumination is
insufficient such as when using the camera outdoors at night or
when an object is a long way from the camera (more than 3 m).
When this camerais used withits housing, set the infrared illumination
switch to OFF. If it is used in the AUTO position, the best quality
picture may not be obtained.
EJ VIDEO IRIS connector
If the plug on the cable is of a different type, replace it with the
provided 3-pin iris plug.
Pin assignment: VIDEO IRIS connector (3-pin)
Pin No.
1 GND
2 E 1 2 Video (0.7 V(p-p} high
Signal
impedance, no sync)
3 DC 9 -10V
(50 mA max.)
Camera connettor
viewed from the outside.
DC IRIS connector
If the plug on the cable is of a different type, replace it with the
provided 4-pin iris plug.
KE Picture adjustment section
==
|
°
@ White balance adjustment switch
This is used for changing the setting of the white balance.
MANU: Manual adjustment is possible.
ATW : Accepts different types of lighting (color temperatures
ranging from approx. 2850 K to 7000 K) using an
automatic tracking system,
0: : For shooting under the artificial light such as halogen
lamps (color temperature approx. 3200 K).
7
Note:
e The automatic tracking system may not function property
when shooting with non-standard lighting or lighting with a
color temperature that exceeds the range of the camera.
Because it uses a TTL system, if a colored object is shot
(especially one with a single color) that fills most of the cam-
era's field of view, the color temperature may be judged
incorrectly and the correct white balance adjustment may
\
« not be possible. In such a case, set to the “MANU” position. |
Pin assignment: DC IRIS connector (4-pin)
3 4 Pin No. Signal
1 Control (-)
2 Control (+)
3 Drive (+)
4 Drive (-)
1 2
Camera connector
viewed from the outside.
Power input terminal (DC 12 V=== , AC 24 VV)
Connect a DC 12 V+10% or AC 24 V+10%, 60 Hz (U type), 50/60 Hz
(E type) power source.
AC24V ~~
|
|
>
LA
+
LLO
Pa
ос 12 у - PISE
Power
Source +1
-- 1K
DC AC 24 V
Power
L………… Da Source
(CLASS 2 ONLY: U type)
Note:
When this camera is used with a power supply lower than DC 10.8
V, afuse may be blown. Also, if itis used with a power supply higher
than AC 26.4 V, a malfunction may occur.
POWER indicator
Lights when the camera is powered.
@ White balance adjustment controls
When the white balance adjustment switch is set to “MANU”,
the white balance can be adjusted manually.
G-Mg: Turn to the “G” side to adjust the green level. Turn to the
“Mg” side to adjust the magenta level.
Turn to the “B” side to adjust the blue level. Turn to the “R”
side to adjust the red level.
B-R:
@ Sync mode switch |
Switches between the internal/external sync mode (automatic) and
the line-lock mode.
LL position:
In the line-lock setting, the camera's vertical synchronization can be
driven by the AC signal in the power lines. To select power lines
phase-locked sync, set the switch to the LL position.
Notes:
e Do not supply the external reference sync signal when using the
camera in line-lock mode.
e Line-lock sync operation is possible only when used with an AC
power source (AC 24 V, 60 Hz: U type, 50 Hz: E type)
МЕ {internal/external) position:
Select internal/externat sync by setting the sync mode switch to the
VE position with this setting, when the external reference sync signal
is input, the camera switches to the external sync mode, and when
no signal is input, the camera switches to the intemal sync mode
automatically.
Factory-preset: VE
@ V phase adjustment
If the camera is to be used in the line-lock sync mode, the vertical
phase may require adjustment to synchronize the vertical phase of
the camera with other cameras in the system. (Vertical phase is
adjustable over the range of +90")
Make this adjustment when the vertical phase of the camera does not
match with other cameras (or systems). For correct adjustment, use
a multichannel oscilloscope. This vertical phase adjustment can only
be made when the camera is operating in the line-lock sync mode.
7
N
Notes:
e When adjusting the V phase control to observe the AC 24 V
e Thisadjustmentis necessary only whentheline-lock sync operation
e For more details, consult your locai dealer.
\
waveform, connect the positive pin of a probe to either of the
power input connectors.
is performed.
J
© BLC (Back Light Compensation) switch
This function makes the iris focus on an object to be shot and is
located near the center position of the screen.
|
+
Photometric area
Set this switch to “ON” at the time of back-light.
SHUTTER speed select switch
This varies the electronic shutter speed. Normally, when a fast-
moving object is being shot, still or slow-motion played-back pictures
will be blurred. In this case, switching the shutter speed from the
normal speed of 1/60 second: U type, 1/50 second: E type to a faster
speed allows each frame to be recorded with greater detail, at the
higher speed.
© AGC (Automatic Gain Control) switch
This automatically increases the camera's sensitivity when the
level of ambient light drops.
ON (upper side) OFF (lower side) Factory preset: ON
© H phase adjustment
For adjusting the horizontal phase when gen-lock operation
is performed. Adjust with reference to other camera(s) in the
system.
© SC phase fine adjustment control
@ SC phase course switch
For adjusting the color sub-carrier phase when gen-lock operation is
performed. Adjust by changing the setting of the SC phase coarse
adjustment switch (A/B) in conjunction with the SC phase fine
adjustment control with reference to other camera(s) in the system.
Oo ¡RIS LEVEL control
The brightness control of the monitor picture does not operate
correctly, adjust using this control. Tum OFF the AGC switch (set to
ON at the factory) to adjust the IRIS LEVEL control.
When using amanual iris lens, the brightness of the picture image will
be fixed by setting this switch in AUTO (Automatic electronic shutter)
position, as the shutter speed is automatically varied according to
the light incident.
Switch position Shutter speed
1/60 second: U type
NORM [=] [=] I) [= 1/50 second: E type
Normally, set to this position
FL UC
. 3900 FLICKER LESS MODE
can be set either in Ё 120 second: E ие)
upper or lower position.) |= УР
125 JE 1/125 second
250 JJEk 1/250 second
500 eE] 1/500 second
1000 EE) 1/1000 second _
2000 LEP 1/2000 second
4000 [JULIET 1/4000 second
10000 FO 1/10000 second
AUTO НПО Automatic electronic
(Switches No. 3 and 4 shutter function (AES)
can be set either in (Do not set this switch in this posi-
upper or lower position.) tion when using an auto-iris lens.)
Notes:
® Faster shutter speeds require more light than the normal
speed.
e If the camera is used under a fluorescent light with the high-
speed shutter, the white balance or brightness may change.
e If a high-intensity subject is shot, smear (bright vertical lines)
tend to appear as the shutter speed increases.
Monitor picture Adjustment direction
To make it brighter Turn clockwise.
To make it darker
Turn counterclockwise.
~
Notes:
e This function is activated when the camera SHUTTER speed
select switch is set to AUTO position and when using the
galvanometric-iris lens or the video-iris lens.
e Be careful not to turn the IRIS LEVEL control beyond its limits as
this could cause a malfunction in the camera's auto-iris control.
J
Lens that can be used
e Use 1/2, 1/3, or 1 inch video camera C-mount lenses with this unit.
a Notes: y
e Theautomaticiris lens operates within DC 9 V to 10 V with a power
consumption of 50 mA or less.
e “L” in the illustration below should be as shown in the follow-
ing table. If “L” exceeds the value in the table, it may dam-
age the inside of the camera and correct mounting may be
impossible; never use such lenses.
Recommended
focal point Lens | Flange back | Distance L
t C-mount 17.526 Less than
o Г | lens mm 5 mm
—
7
tens |
Flange back (in AIR)
e Lenses designed for color video cameras are recommended.
Lenses designed for B/W cameras may have inferior color
reproduction and picture quality. In particular, they are not
suitable for use outdoors or in very bright conditions. When
using a lens with an ND filter attached, shooting may not be
possible with the minimum required illumination specified.
Because camera functioning is based on infrared ray reception in
the B/W mode, using a zoomlens when shooting inthe B/W mode
may cause the lens to go out of focus. This is not a malfunction.
To avoid this, focus the lens manually or use a fixed-focus lens.
N _
e When using the buitt-in infrared illumination
Select a lens with the size which does not shut off the infrared
illumination. Use the figure below as reference.
Limit of infrared
illumination Co
em Camera
у МС
COLOR VILO CAMERA TANTE ||
Less than
60 mm dia.
|
/
|
Lens
Less than 97 mm
With a fixed-focus lens
1.
2.
3.
4.
Turn the lock screw counterclockwise to loosen.
Fully open the aperture and set the focus ring to “=” (infinity), then
shoot the subject from as far away as possible. Adjust using a subject
further away than the one to be shot.
® In the case of an auto-iris lens only, shoot a comparatively
dark object so that the aperture is open.
Turn the FOCUS screw to focus with a screwdriver.
Turn the lock screw clockwise to secure.
With a zoom lens
1.
Turn the lock screw counterclockwise to loosen.
2. Shoot a subject that is approx. 3 m away.
3. Fully open the aperture and set the lens to the maximum tele-
Back Focus adjustment photo position. Then turn the focus ring to focus. |
* In the case of an auto-iris lens only, shoot a comparatively
When a lens is mounted, adjustment of the back focus (the distance from dark object so that aperture is open
the lens mounting position to the focal point) may sometimes be required. 4. Set the lens to its maximum wide-an gle position
Adjust when the correct focus cannot be obtained with the lens focus Turn the FOCUS screw to focus with a screwd riv er
ring. 5. Repeat steps 3 — 4 until the difference between focusing position 3
Caution: and 4 becomes smallest.
: | o 6. Turn the lock sc | |
e Do not forcibly turn the FOCUS screw, as it will cause dam- - rew clockwise to secure
age to the camera.
LOCK screw 9
FOCUS screw
e Do not turn any component's power on until all connections are completed. r
* Also read the instruction manuals of all the equipment used carefully. Notes: )
- a ; : e If the external sync signal to be input is less than 65% with
Example: When a single camera is used
Automatic iris lens with EE amplifier
(ones without EE amplifier)
To VIDEO IRIS connector
(To the DC IRIS connector on the side panel)
To power input terminal
Power source
(DC12V) / (AC24V)
(CLASS 2 ONLY: U type)
Caution:
respect to.the reference levei, sync operation is not possible.
Reference Composite video signal (VBS) | 1.0 Y(p-p)*
level Black burst signal (BB) 0.43 V{p-p}: U type
0.45 V(p-p}: E type
* The video components of the signal do not matter.
» Gen-lock operation may become unstable using a signal
containing severe jitter {vertical or horizontal picture vibra-
tions) such as a video recorder playback signal.
* When gen-lock operation is performed, adjustment of hori-
« zontal phase and color sub-carrier phase are required. )
To VIDEO input connector
TTT Ts +
From BB signal output or
! composite video signal output Monitor
Reference sync
signal generator
e Be sure not to connect the power source until all other connections are complete.
Do not turn the power of any equipment on until connections are compieted.
» Use a DC 12 V power source with ripple voltage of less than 50 mV.
» Do not connect to DC 12 V and AC 24 V power sources at the same time.
10
SPECIFICATIONS
Television system
Pickup element
Pickup area
Number of effective
pixels
Sync system
External sync input
Video output
Video signal-to-
noise ratio
Resolution
Minimum required
illumination
Limit of infrared
illumination
Infrared illumination
Lens mount
Power requirement
Power cons imption
: NTSC (U type)
PAL (E type)
: Interiine-transfer system 1/3-inch CCD x 2 (for
black/white and color, each)
: 1/3-inch optical size 4.8 (H) x 3.6 (V) mm
: 768 (horizontal) x 494 (vertical) (U type)
752 (horizontal) x 582 (vertical) (E type)
(each for black/white and color)
; Internal/external/power source sync (U type :
60 Hz areas only, E type : 50 Hz areas only)
: Composite video signal (VBS) : 1 V (p-p), 75
ohms terminated (or black burst signal (BB),
0.43 V (p-p) : NTSC,
0.45 Y (p-p) : PAL, 75 ohms terminated)
: Composite video signal : 1 V (p-p), 75 ohms,
unbalanced
: 50 dB (Color mode)
: 470 TV lines (horizontal) (U type),
460 TV lines (vertical) (E type)
: 2 Ix (F1.2, AGC switch set to “ON”, in color
mode)
O ix (Infrared illumination switch “ON”, in black/
white mode)
: 3m (F 1.2, in black/white mode)
: Lighting in the black/white mode (when set to
AUTO)
: C mount
- DC 12V+10% or AC24V+10%, 60Hz (Utype),
50/60 Hz (E type)
: 13 W (with infrared illumination on)
7.5 W (with infrared illumination off)
Operating tempera-
ture range
Weight
: =10°C to 50°C (operation),
0°C to 40°C (recommended)
: 700 9
Provided accessories: 3 P IRIS PLUG, 4P IRIS PLUG
Dimensions
: (Unit : mm)
Dimension
7
о
and lower sides)
и
e Design and specifications subject to change without notice.
VICTOR COMPANY OF JAPAN, LIMITED
Printed in Japan
SC96701
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement