Aristo 300 Aristo 400 Aristo 500

Aristo 300 Aristo 400 Aristo 500
GB
Aristo 300
Aristo 400
Aristo 500
Instruction manual
0462 152 001 GB 101119
Valid for serial no. 033-xxx-xxxx, 044-xxx-xxxx
DECLARATION OF CONFORMITY
According to
The Low Voltage Directive 2006/95/EC of 12 December 2006, entering into force 16 January 2007
The EMC Directive 2004/108/EC of 15 December 2004, entering into force 20 January 2005
Type of equipment
Welding power sources for MIG/MAG welding
Brand name or trade mark
ESAB
Type designation etc.
Aristo® 300, Aristo ® 400, Aristo ® 500, Valid from serial number 033 xxx xxxx (2010 w.33)
Aristo® 300, 400 and 500 may be used with different MMC panels in combinations with or without water
Manufacturer or his authorised representative established within the EEA
Name, address, telephone No, telefax No:
ESAB AB, Welding Equipment
Esabvägen, SE−695 81 LAXÅ, Sweden
Phone: +46 584 81 000, Fax: +46 584 411 924
The following harmonised standard in force within the EEA has been used in the design:
EN 60974−1, Arc welding equipment – Part 1: Welding power sources
EN 60974−10, Arc welding equipment – Part 10: Electromagnetic compatibility (EMC) requirements
Additional information: Restrictive use, Class A equipment, intended for use in locations other than residential
By signing this document, the undersigned declares as manufacturer, or the manufacturer’s authorised
representative established within the EEA, that the equipment in question complies with the safety
requirements stated above.
Place and Date
Laxå 2010−09−15
Signature
Position
Global Director
Equipment and Automation
Kent Eimbrodt
Clarification
-2-
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
2.2
4
6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel A44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
4.1
4.2
4.3
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lifting instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
8
9
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection of welding and return cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turning the power source on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIG/MAG and FCAW-S welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMA welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIG welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
12
12
12
13
13
13
13
13
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
6.1
Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
7 FAULT TRACING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
16
18
19
20
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves. Note! Do not use safety gloves when replacing wire.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
WARNING
Do not use the power source for thawing frozen pipes.
-4ba43de
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precausions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION
This product is solely intended for arc welding.
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
-5ba43de
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
The Aristo 300/400/500 series is a welding power source intended for MIG/MAG
welding, as well as for welding with powder filled cored wire (FCAW-S), live TIG
welding (power source with panel A44) and for welding with coated electrodes
(MMA).
The power sources are intended for use with the following wire feed units:
S
Aristo F 300
S
MobileFeed 300
ESAB's accessories for the product can be found on page 20.
2.1
Equipment
The power source is supplied with:
S
5 m return cable with earth clamp
S
5 m mains cable with 32 Amp connector
S
instruction manual for the welding power source
S instruction manual for the control panel (if applicable)
Instruction manuals in other languages can be downloaded from the website,
www.esab.com.
2.2
Control panel A44
See separate instruction manual for
detailed description of the panels.
-6ba43de
GB
3
TECHNICAL DATA
Aristo 300
Mains voltage
Mains supply Sscmin
from serial number 033-xxx-xxxx
from serial number 044-xxx-xxxx
Mains supply Zmax
from serial number 044-xxx-xxxx
Primary current
mains voltage 380V
mains voltage 400V
mains voltage 440V
Aristo 400
Aristo 500
380-440V, +/- 10%, 3∼ 50/60 Hz
3.0 MVA
3.8 MVA
4.0 MVA
6.0 MVA
5.0 MVA
8.4 MVA
-
-
0,22 Ω
18A
17A
16A
26A
25A
23A
35A
34A
31A
No-load power
40 W
Setting range (DC)
MIG/MAG
MMA
TIG
8-48V
16-300A
4-300A
8-48V
16-400A
4-400A
8-48V
16-500A
4-500A
Permissible load at MIG/MAG
60 % duty cycle
80 % duty cycle
100% duty cycle
300 A / 29.0 V
400 A / 34.0 V
300 A / 29.0 V
500 A / 39.0V
400 A / 34.0V
300 A / 29.0V
Permissible load at MMA
60 % duty cycle
80 % duty cycle
100% duty cycle
300 A / 32.0 V
400 A / 36.0 V
300 A / 32.0V
500 A / 40.0 V
400 A / 36.0 V
300 A / 32.0 V
Permissible load at TIG
60 % duty cycle
80 % duty cycle
100% duty cycle
300 A / 22.0 V
400 A / 26.0 V
300 A / 22.0 V
500 A / 30.0 V
400 A / 26.0 V
300 A / 22.0 V
Power factor at maximum current
0,91
0,92
0,93
Efficiency at maximum current
87 %
88 %
89 %
Open circuit voltage
VRD function inactive1)
VRD function active1)
55V
<35V
Operating temperature
-10 to +40° C
Transportation temperature
-20 to +55° C
Constant sound pressure when
idling
<70 db (A)
Dimensions lxwxh
610 x 250 x 445 mm
Weigh
40 kg
Insulation class
H
Enclosure class
IP 23
Application classification
1) The
VRD function is explained in the instruction manual for the control panel.
Mains supply, Ssc min
Minimum short circuit power on the network in accordance with IEC 61000-3-12
Mains supply, Zmax
Maximum permissible line impedance of the network in accordance with IEC 61000-3-11.
-7ba43de
GB
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld at a cer­
tain load without overloading. The duty cycle is valid for 40° C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
4
INSTALLATION
The installation must be executed by a professional.
CAUTION
This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.
WARNING
Straps must be used when lifting the power
source. The handle is only intended for
pulling it.
4.1
Location
Position the welding power source such way that its cooling air inlets and outlets are not obstructed.
4.2
Lifting instruction
-8ba43de
GB
4.3
Mains supply
Note
Mains supply requirements
High power equipment may, due to the primary current drawn from the mains supply, influence the
power quality of the grid. Therefore connection restrictions or requirements regarding the
maximum permissible mains impedance or the required minimum supply capacity at the interface
point to the public grid may apply for some types of equipment (see technical data). In this case it
is the responsibility of the installer or user of the equipment to ensure, by consultation with the
distrubution network operator if necessary, that the equipment may be connected.
-9ba43de
GB
Check that the unit is connected to the correct mains power supply voltage, and that
it is protected by the correct fuse size. A protective earth connection must be made,
in accordance with regulations.
Rating plate with supply connection data
Recommended fuse sizes and minimum cable areas
Aristo 300
Mains voltage
Mains cable area
Aristo 400
Aristo 500
380-440V, +/- 10%, 3∼ 50/60 Hz
4G4
mm2
4G4 mm2
4G6 mm2
Phase current Ieff
Uin 380V
18 A
24 A
28 A
Fuse anti-surge
Fuse CMCB-surge
20 A
20 A
25 A
32 A
35 A
32 A
Phase current Ieff
Uin 400V
17 A
23 A
27 A
Fuse anti-surge
Fuse CMCB-surge
20 A
20 A
25 A
32 A
35 A
32 A
Phase current Ieff
Uin 440V
16 A
21 A
24 A
Fuse anti-surge
Fuse CMCB-surge
20 A
20 A
25 A
25 A
25 A
32 A
NB: The mains cable areas and fuse sizes as shown above are in accordance with Swedish
regulations. They may not be applicable in other countries: make sure that the cable area and fuse
sizes comply with the relevant national regulations.
- 10 ba43de
GB
5
OPERATION
General safety regulations for the handling of the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING
AH 0935
Fasten the equipment - particularly if the
ground is uneven or sloping.
- 11 ba43de
GB
5.1
Connections and control devices
1
Mains supply switch
4
Connection for welding current cable (+)
2
Indicating lamp, power supply ON
5
Control cable socket (from / to wire feed
unit) or remote control
3
Indicating lamp, overheating
6
Connection for welding current cable (-)
5.2
Connection of welding and return cable
There are two terminals on the power source, a positive terminal (+) and a negative
terminal (-), for connecting welding and return cables. Selected welding method and
type of used electrode determines to which terminal the welding and the return cable
should be connected to. Before welding make sure that cables are firmly attached to
the power source, and that return cable clamp is properly attached on the workpiece.
5.3
Turning the power source on/off
Turn the machine on by turning switch (1) to the ”1” position. Turn the machine off by
turning the switch (1) to the ”0” position. Regardless the mains supply is interrupted
abnormally or the machine is switched off in the normal manner, the welding data will
be stored, so it will be available next time the unit is turned on.
5.4
Fan control
The power source has a time circuit, which keeps the fans running for 6.5 minutes
after welding has stopped, then the unit switches to energy-saving mode. The fans
start again when welding begins. The fans run at reduced speed for welding currents
up to 200 A, and at full speed for higher currents.
- 12 ba43de
GB
5.5
Overheating protection
The welding power source has overheating protection circuit that operates if the
internal temperature becomes too high. When this occurs the welding is blocked and
a fault code is displayed on the control panel. The overheating protection resets
automatically when the temperature has fallen down.
5.6
Remote control unit
For more information about the operation of the remote control unit, see the
operating instructions for the control panel.
5.7
MIG/MAG and FCAW-S welding
An arc melts a continuously supplied wire. The weld pool is protected by shielding
gas. For MIG/MAG and FCAW-S welding, the power source is supplemented with:
S
S
S
S
wire feed unit
welding torch
connection cable between power source and wire feed unit
shielding gas bottle
5.8
MMA welding
For welding with coated electrodes, the power source is supplemented with:
S
welding cable with electrode clamp.
5.9
TIG welding
TIG welding melts the workpiece, using the arc struck from a tungsten electrode, that
does not melt itself. The weld pool and the electrode are protected by shielding gas.
For TIG welding, the welding power source is supplemented with:
S
S
S
TIG torch with tungsten electrode and gas valve
argon gas bottle
argon gas regulator
”Live TIG-start”
At a ”Live TIG-start” the tungsten electrode must touch the workpiece. When the
electrode is then lifted away from workpiece, the arc is struck with limited current
value (12 - 15 A).
- 13 ba43de
GB
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any faults.
6.1
Inspection and cleaning
Check regularly that the power source is free from dirt.
The power source should be regularly blown clean using dry compressed air at
reduced pressure. More frequently in dirty environments.
Otherwise the air inlet/outlet may become blocked and cause overheating. To avoid
this, the airfilter should be regurarly cleaned.
Replacing and cleaning the dust filter.
S
S
S
S
Release the dust filter according to the figure.
Blow the filter clean with compressed air (reduced pressure).
Ensure that the filter with the finest mesh is placed towards the grille.
Reinstall the filter.
- 14 ba43de
GB
7
FAULT TRACING
Try these recommended checks and inspections before sending for an authorised
service technican.
Type of fault
Actions
S
S
No arc.
S
Welding current is interrupted
during welding
S
S
Check that the mains power supply switch is turned on.
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check whether the thermal overload trip has operated
(indicated by the orange lamp on the front)
Check the main power supply fuses.
The thermal overload trips
operate frequently
S
S
Check to see whether the air filters are clogged.
Make sure that you are not exceeding the rated data for the
power source (i.e. that the unit is not being overloaded).
Poor welding performance.
S
Check that the welding current supply and return cables are
correctly connected.
Check that the correct current value is set.
Check that the correct welding wires are being used.
Check the main power supply fuses.
S
S
S
8
ORDERING OF SPARE PARTS
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Aristo 300, Aristo 400, Aristo 500 is designed and tested in accordance with the inter­
national and European standards EN 60974-1 and EN 60974-10. It is the obligation of
the service unit which has carried out the service or repair work to make sure that the
product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 15 ba43de
Diagram
- 16 ba43e
Edition 101119
- 17 ba43e
Edition 101119
Aristo 300, Aristo 400, Aristo 500
Ordering number
Ordering no.
Denomination
Type
Notes
0462 153 880 Welding power source Aristo®300
Without control panel
0462 183 882 Welding power source Aristo®300 A44
With control panel
0462 154 880 Welding power source Aristo®400
without control panel
0462 154 882 Welding power source Aristo®400 A44
With control panel
0462 155 880 Welding power source Aristo®500
With control panel
0462 155 882 Welding power source Aristo®500 A44
Without control panel
0459 839 049 Spare parts list
Aristo®300, Aristo®400, Aristo®500
0462 305 001 Instruction manual
Cooling unit COOL 1
0463 009 074 Instruction manual
Control panel A44
Instruction manuals and the spare parts list are available on the Internet at www.esab.com
- 18 ba43o
Edition 101119
Aristo 300, Aristo 400, Aristo 500
Spare parts list
Item
1
ba43s
Ordering no.
Denomination
0462 197 001 Dust filter
- 19 -
Edition 101119
Aristo 300, Aristo 400, Aristo 500
Accessories
Trolley . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 151 880
Spare parts list for trolley . . . . . . . . . . . . . . . . . . . 0459 839 039
Trolley bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . 0463 125 880
option when no cooling unit is assembled
Aristo F 300 MA43 . . . . . . . . . . . . . . . . . . . . . . .
Aristo F 300 MA43, with water . . . . . . . . . . . .
Aristo F 300 MA44 . . . . . . . . . . . . . . . . . . . . . . .
Aristo F 300 MA44, with water . . . . . . . . . . . .
0462 250 883
0462 250 893
0462 250 884
0462 250 894
MobileFeed 300 AVS . . . . . . . . . . . . . . . . . . . . . 0558 005 728
Cooling unit COOL 1 . . . . . . . . . . . . . . . . . . . . . 0462 300 880
ba43a
- 20 -
Edition 101119
Aristo 300, Aristo 400, Aristo 500
Connection set, 70 mm2
With12 pole (8+4) cable plug/socket
2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 780
5 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 781
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0462 150 782
0462 150 783
0462 150 784
0462 150 785
Connection set water, 70 mm2
With12 pole (8+4) cable plug/socket
2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 790
5 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 791
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0462 150 792
0462 150 793
0462 150 794
0462 150 795
Connection set, 95 mm2
With12 pole (8+4) cable plug/socket
2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 980
Connection set water, 95 mm2
With12 pole (8+4) cable plug/socket
2 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 150 990
Remote control unit MTA1 CAN . . . . . . . . . . . 0459 491 880
MIG/MAG: wire feed speed and voltage
MMA: current and arc force
TIG: current, pulse and background current
Remote control unit AT1 CAN . . . . . . . . . . . . 0459 491 883
MMA and TIG: current
Remote control unit AT1 CF CAN . . . . . . . . . 0459 491 884
MMA and TIG: rough and fine setting of current
ba43a
- 21 -
Edition 101119
Aristo 300, Aristo 400, Aristo 500
Remote control cable 12 pole (8+4)- 4 pole
0.25m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 958 880
5m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 958 881
10m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 958 882
25m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0462 958 883
For more information of the accessories contact the nearest ESAB agency.
ba43a
- 22 -
Edition 101119
NOTES
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
.............................................................................................................................................................
- 23 notes
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
Asia/Pacific
Representative offices
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA
LLC ESAB
Moscow
Tel: +7 095 543 9281
Fax: +7 095 543 9280
LLC ESAB
St Petersburg
Tel: +7 812 336 7080
Fax: +7 812 336 7060
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
ESAB AB
SE-695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
081016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising