Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
Installation Instructions
Self-Contained Hopper Spreader
TAble of CoNTeNTS
General Information
Safety Precautions
Warranty Information
Installation Instructions
Spreader Operation
Spreader Maintenance
Repair Parts & Drawings
5
7
8
3
3
1
2
Note: This manual applies to spreaders equipped with
Tecumseh Formula XL/C 10.0 HP. engine, serial number
2810 and above.
CAUTION! Do not overload vehicle beyond the vehicle
GVWR or GAWR. Check the vehicle’s load rating certification sticker for maximum vehicle capacity.
Average Material Weights:
MATERIAL
#1 Rock Salt
#2 Rock Salt
Coarse Sand - Dry
Coarse Sand - Wet
WEIGHT (POUNDS PER CUBIC YARD)
950
1,215
2,565
3,240
Note: To calculate the total spreader weight (including ice control material); add the empty spreader weight plus the ice control material and spreader accessories.
GeNeRAl INfoRMATIoN
Spreader Model Numbers:
SCH096C - 8’ spreader w/ standard length spinner/chute,
(carbon steel).
SCH096SS - 8’ spreader w/ standard length spinner/chute,
(stainless steel).
SCH096CX - 8’ spreader w/ extended length spinner/chute,
(carbon steel).
SCH096SSX - 8’ spreader w/ extended length spinner/chute,
(stainless steel).
Spreader Specifications:
Overall Length:
Overall Width:
113 inches
50-3/4 inches
Overall Height: 32-1/2 inches
Empty Weight (excludes accessories, fuel, and salt/sand):
Carbon Steel - 820 lbs.
Stainless Steel - 620 lbs.
Capacity Struck:
Capacity Rounded:
1.8 cubic yards
2.1 cubic yards
Hopper Storage Capacity
1.8 CU YD
1.0 CU YD
0.5 CU YD
12”
19”
Recommended fastener Torques:
Maintain all fastener torques as shown in the following table. Failure to do so may cause injury to persons.
1/4-20
5/16-18
3/8-18
3/8-24
7/16-14
1/2-13
9/16-12
5/8-11
SAE GRADE 2 ft-lbs
30
45
66
93
6
11
19
24
SAE GRADE 5 ft-lbs
9
18
31
46
50
75
110
150
Vehicle Requirements:
3/4 or 1 ton pick-up truck above 8500# GVWR.
27”
Quality since 1946
engine and Gearbox oil:
The engine crankcase is filled with 1 quart of SAE 5W-30 motor oil at the factory. The gearbox is filled with SAE 90 gear lubricant at the factory.
Warning! Verify that the above oil viscosity meets your operating requirements. If not, empty and refill with the proper viscosity. Before starting spreader, check that the engine crankcase and gearbox are filled to the proper level with lubricant.
SAfeTY PReCAUTIoNS
Warning! Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided.
1. Read this entire Owners Manual before operating this spreader. This includes the Tecumseh Formula XL/C 10 hp. engine Operator’s Manuals.
2. Read all safety decals on the spreader before operating.
3. Check to make sure all safety guards are securely mounted into place before operating this spreader.
4. Make sure the engine cover is securely fastened to the spreader before operating the spreader.
5.
Verify that all personnel are clear of the spreader spray area before starting or operating this spreader.
6. Keep all loose clothing, hair, jewelry and limbs clear of the spreader before starting or operating this spreader.
7. Do not over-load your vehicle beyond payload limits. If there are any questions, contact the vehicle manufacturer.
8. Do not adjust, clean, oil or unclog material jambs without first turning off the spreader, removing the engine spark plug connector.
9.
Do not climb on or in the spreader during operation.
Do not ride on the spreader while the vehicle is in motion.
10. Make sure the spreader is securely fastened to the vehicle in accordance with this manual.
11
.
Do not operate a spreader that is in need of maintenance or repairs.
12.
Never lay tools or equipment on top of the 12 VDC spreader’s battery. This could accidentally ground the positive (+) battery terminal, resulting in electrical shock, burns or damage to the vehicle or equipment.
13.
Avoid contact with battery acid. Battery acid can seriously burn eyes or skin. Battery acid can also burn holes in clothing.
14.
Always disconnect the battery before removing or replacing electrical components.
15.
A charging battery gives off gases that can explode if touched by a spark or flame. Cover the top of the battery with electrically non-conductive material to keep sparks away from battery gases.
16.
If the spreader must be operated with the spreader battery disconnected, insulate the positive (red) battery cable and red wire from the engine alternator with electrical tape.
17.
Do not use side extensions on the T304 Stainless Steel spreader to increase salt storage capability. Using side extensions may damage hopper and cause injury to personnel.
SCH096 SPReADeR WARRANTY
INfoRMATIoN
T his warranty replaces all previous warranties and no employee of this company is authorized to extend additional warranties, or agreements, or implications not explicitly covered herein.
Buyers Products Company warrants all parts of the product to be free from defects in material and workmanship for a period of one (1) year, excluding the Tecumseh gasoline engine, from the date of installation. Parts must be properly installed and used under normal conditions. Normal wear is excluded.
Any part which has been altered, including modifications, misuse, accident, or lack of maintenance will not be considered under this warranty.
Quality since 1946
The sole responsibility of Buyers Products Company under this warranty is limited to repairing or replacing any part(s) which are returned, prepaid, 30 days after such defect is discovered, and returned part(s) are found to be defective by Buyers Products Company.
Authorization from Buyers Products Company must be obtained before returning any part. The following information must accompany defective parts returned to Buyers
Products Company: RMA #, spreader model, serial number, date installed, and distributor from whom purchased.
Buyers Products Company shall not be liable for damage arising out of failure of any unit to operate properly, or failure, or delay in work, or for any consequential damages. No charges for transportation or labor performed on any part will be allowed under this warranty.
The 10.0 HP gasoline engine is solely warranted through
Tecumseh Products Company. All warranty claims are to be processed through Tecumseh Products Company. This information is explained in the Tecumseh Engine owner’s manual.
Please photocopy and complete this information and mail it to the following address to validate this warranty:
Name:
Company:
Address:
Spreader Model:
buyers Products Company
9049 Tyler blvd.
Mentor, ohio 44060.
Serial No.:
Installation Date:
Purchase From:
INSTAllATIoN INSTRUCTIoNS
1. Mounting the Spreader onto the Vehicle:
A. Remove the tailgate from the vehicle.
B. Lift the carbon steel spreader by means of the lifting loop that is welded to the hopper cross channel. Lift the stainless steel spreader by means of the square knock-out in the rear-most (toward rear of the truck) hopper cross member.
Warning! The lifting device must be adequately rated to lift a payload equal to or greater than the spreader weight.
See page 2 for spreader weights.
The lifting loop is placed at the approximate balance point of the spreader. Residual material, gasoline, oil, battery, top screen, or inverted vee assembly may affect this balance point.
C.
Elevate the spreader off the vehicle with lumber. Place lumber under the side gussets of the spreader. This will help with removal of excess material that accumulates under the spreader.
D. Center the spreader on the vehicle with the ends of the sill extensions 14” to the rear of the nearest vertical obstruction (bumper, trailer hitch, etc). It is recommended that the Spinner/Chute Assembly be loosely attached to the hopper. This should be done to avoid any interference between the vehicle and the Spinner/Chute Assembly.
E. Bolt the spreader to the vehicle frame using the holes located in each of the four (4) side gussets. Use 1/2” SAE
Grade 5 hardware as required by vehicle application.
F. In addition secure the spreader to the vehicle using the four (4) tie-down eyes located at each corner of the spreader to the vehicle’s factory installed anchor points using proper tie-down devices.
The spreader must be securely fastened to the frame of the vehicle.
Verify with the vehicle’s manufacturer that the factory installed anchor points are designed for tie-down of such load.
Periodically check that the spreader mounting hardware is securely tightened.
2. Mounting the Spinner/Chute Assembly
A. Attach the Spinner/Chute Assembly to the spreader using the four (4) 3/8-16 X 5/8” hex head bolts, lock washers, and nuts. The head of the bolt is to be placed on the inside of the chute assembly. Push the chute assembly towards the cab of the vehicle. Loosely attach the hardware, but do not tighten at this time.
3
B. Install the roller chain between the sprocket mounted to the Spinner/Chute Assembly and the Gearbox Sprocket.
Make sure both sprockets are in-line with one another.
Quality since 1946
Tighten the Gearbox Sprocket set screw. Install the roller chain master link.
C. To adjust the roller chain tension, loosen the Spinner
Shaft bearing bolts and slide the shaft away from the
Gearbox Sprocket. Be sure to maintain the vertical alignment of the Spinner Shaft and Bearings before tightening the hardware. The correct chain tension should allow a
5/16” deflection midway between both chain sprockets.
Caution! Do not over-tension the roller chain. This can cause damage to the chain, bearings, and gearbox.
D.
Install the chain guard using the three (3) 1/4-20 X 3/4” hex head bolts, lock washers, and nuts.
E.
Tighten all hardware to the recommended torque specifications as shown in this manual.
3.
Control box and Vehicle Wiring Harness Installation.
Note: The following instructions show how to install the spreader so that the engine will draw power, to start the engine, from a dedicated battery located on the spreader
CAB CONTROL BOX
D. Connect the stripped end of the red wire to an accessory wire/terminal that is controlled by the vehicle’s ignition switch.
4. Spreader Wiring Installation
A.
Attach the terminal end of the black (negative) battery cable to the negative terminal (marked “-”) on the battery.
B.
Then connect the terminal end of the red (positive) battery cable to the positive terminal (marked “+”) on the battery.
C.
Using cable straps and 1/4” x 3/4” sheet metal screws, secure the spreader wiring harness to the spreader.
Predrilled holes are provided for securing the sheet metal screws.
D.
Verify that the Ignition Switch in Control Box is in the
“OFF” position prior to completing step E.
E.
Connect the Spreader and Vehicle Wiring Harnesses.
5.
Installing the Inverted Vee Assembly
(optional equipment)
Carbon Steel Unit:
Secure the Deflector Weldment (inverted vee) to the Support
Weldments (Support Weldments are welded into the hopper) with four (4) 3/8-16 X 1” hex head cap screw, lock washers, and nuts.
Stainless Steel:
The front and rear hopper cross members have two (2) predrilled holes in each to support the Stainless Steel Deflector
Weldment. Secure the deflector with four (4) 3/8-16 X 1” hex head cap screws, lock washers, and nuts.
A. Layout a wiring path for the Vehicle Wiring Harness.
Warning! Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling.
B. Mount the Control Box in a convenient location in the truck cab.
C. Connect the green wire from the Vehicle Wiring
Harness to a known vehicle ground.
4
Quality since 1946
A.
Adjust the height of the inverted vee for the material being spread:
• For salt and dry sand, adjust the Deflector Weldment as close to the bottom of the hopper as possible.
• For salt/sand mix, adjust the Deflector Weldment to the middle of the mounting holes.
• For wet sand, adjust the Deflector Weldment to the highest position.
• Tighten all hardware according to the Torque Chart.
SPReADeR oPeRATIoN
Note: before starting the engine, follow all safety precautions.
1.
A word about the Cab Control box functions:
“OFF” position: While in this position, 12 VDC power is shut off to the spreader. To turn off the spreader, turn key to this position.
“ON” position: While in this position, 12 VDC power is turned on to the spreader.
“START” position: While in this position, the spreader’s engine starter is activated.
C. The Throttle Switch is a two position switch with the following functions:
“FAST” position: While in this position, the engine speed will increase.
“IDLE” position: While in this position, the engine speed will decrease.
2
.
Starting the engine
A. Verify that the Clutch Switch and Ignition Switch on the Cab Control Box are in the “OFF” position.
B. Turn the vehicle ignition to the “ON” position.
C. Turn the Spreader Ignition Switch to the “ON” position.
D. Move the Throttle Switch on the Cab Control Box to the
“Idle” Position and hold for approximately two seconds.
E. Turn the Ignition Switch to the “START” position.
F.
While the engine is cranking, move the Throttle Switch to the “CHOKE/FAST” position.
A. The Clutch Switch is a three position switch with the following functions:
“OFF” position: While in this position, with the engine running, the Spreader Feed Chain and the Spinner Disc will not spin. Therefore, the spreader will not spread ice control material.
G. Release the Throttle Switch when the engine begins to start.
H. Release the Ignition Switch when the engine starts.
“ON” position: While in this position, the Spreader Feed chain and the Spinner Disc will spin with the engine running.
I. After the engine starts, move the Throttle Switch to the
“IDLE” position to release the choke (hold switch for 1/2-1 seconds).
3. Stopping the engine
“BLAST” position: While in this position, with the engine running, the Spreader Feed Chain and the Spinner Disc will spin. In this position switch can only be activated when held into the “BLAST” position.
A
.
Reduce engine RPM by holding Throttle Switch to the
“IDLE” position for 2-3 sec. To stop the engine, turn the
Ignition key to the “OFF” position.
B. The Ignition Switch is a three position switch with the following functions:
5
4. Clutch operation
A. Start the engine and adjust the speed to slightly above idle.
Quality since 1946
B.
Move the Clutch Switch into the “ON” position.
C. Increase the engine RPM by moving the Throttle
Switch.
D. It is recommended that the clutch only be engaged at the lowest possible speed without stopping the engine.
This practice will prevent premature spinner chain failure and chain tension loss.
E. Do not constantly use “Blast” clutch regime. This practice will prevent premature clutch and flex coupler failure and breakage.
Internal baffle Adjustment
BOTH INTERNAL
BAFFLES OUT
LEFT BAFFLE IN,
RIGHT OUT
external baffle Adjustment
RIGHT BAFFLE IN,
LEFT OUT
5. Spinner/Chute Assembly operation
A.
The spread pattern and the amount of material dispensed depends on the following:
Engine RPM.
Feed Gate position.
Baffle Settings.
B.
Keep the following rules in mind:
• Decreasing engine RPM will decrease the amount of material coming to the spinner.
• Increasing engine RPM will increase the amount of material coming to the spinner.
• Size of the Feed Gate opening will increase or decrease the amount of material coming to the spinner.
6
ALL BAFFLES
ADJUSTED DOWN
FOR A CONFINED
SPREAD PATTERN
6.
Precautions
RIGHT BAFFLE
DEFLECTS MATERIAL
DOWN, HEAVY
ON RIGHT SIDE
LEFT BAFFLE
DEFLECTS MATERIAL
DOWN, HEAVY
ON LEFT SIDE
Caution! Always follow the following precautions so as not to cause damage to the spreader
A.
If the feed chain does not move because of dense material or jambs, remove all materials from the hopper and free the chain.
B.
If the material in the hopper freezes, move the spreader into a warm area to thaw.
C. To prevent the feed chain from freezing, do not store material in the spreader.
D. The gearbox is designed to only accept torque from the input shaft. Therefore,
DO NOT ATTEMPT TO FREE
THE FEED CHAIN BY USING A PIPE OR SIMILAR TOOL
TO MOVE OR DISLODGE THE CHAIN. If the feed chain is moved, the gears within the gearbox will strip. This action will void all warranties.
E.
Check and maintain the correct oil level for both the engine crankcase and the gearbox. The engine crankcase is filled with 1 quart of SAE 5W-30 motor oil at the factory.
The gearbox is filled with SAE 90 gear lubricant at the factory.
Warning! The engine crankcase and gearbox must be filled and maintained with oil. The engine crankcase oil must be of the correct viscosity for the intended spreader operating conditions. Refer to the Tecumseh
Engine owner manual to determine the correct viscosity.
Operating the engine or gearbox without oil (or without a sufficient amount of oil) can cause permanent damage to the engine or crankcase.
Quality since 1946
SPReADeR MAINTeNANCe
1. Use dielectric grease on all electrical connections before an electrical connection is made or after a connector is disconnected.
2. Grease the following:
Idler shaft bearings (2).
Drive shaft bearings (2).
Spinner shaft bearings (2).
Flanged bearing located between gearbox and clutch.
3. Check gearbox oil level periodically and maintain the oil level by adding appropriate lubricant.
4. Fill the engine crankcase with recommended oil to the full line. Read the Tecumseh Engine owners manual for the recommended oil viscosity for your operating conditions.
Check the oil level periodically and maintain the oil level.
Clean and lubricate engine’s choke throttle linkage.
5. Check the Feed Chain tension periodically. Check the chain tension by measuring the distance between the end of the sill extensions and the point where the chain contacts the lower flange on the rail. The correct distance between these two points is 26” to 30”. See the diagram below to clarify.
the Spinner Shaft is vertical after any adjustments.
Caution! Do not over-tension either roller chain. Overtensioning can cause damage to bearings, roller chain, sprockets, or the engine.
7. Empty the spreader of all ice control material when not in use to prevent a frozen feed chain.
8.
Wash out the spreader when it is not in use. At the end of the season wash out the spreader to remove all ice control materials. Thoroughly dry all metal surfaces. Paint and oil all bare metal surfaces, to protect from rust. Properly store the spreader for the next season.
9.
To minimize problems and extend the life of the
Electric Clutch, the following procedures are recommended:
A. At the end of the season, remove and clean the clutch.
B. After cleaning, coat both mating surfaces of the clutch with oil or light grease.
C. Remove oil and grease prior to using the clutch again.
10. Engine Repair - Maintain the spreader engine according to the Engine Owner’s Manual. This manual is shipped with the spreader. The engine warranty is covered by
Tecumseh Products Co. If service is required, contact an authorized Tecumseh Service Center.
6.
Maintain the correct tension on the following roller chains:
A. Engine to Gearbox Input Sprocket.
B. Spinner Shaft to Gearbox Input Sprocket.
The correct chain tension allows 5/16” deflection midway between respective sprockets. Oil both roller chains often, and at the end of each season.
To loosen or tighten Chain A, loosen the four (4) 3/8-16 X 1” carriage bolts that fasten the Motor Mount Weldment to the drive base and slide the Engine Mount Stand.
To loosen or tighten Chain B, loosen the Spinner Bearing
Mounting hardware and slide the Spinner Shaft. Verify that
7
Quality since 1946
Repair Parts - Spinner/Chute Assembly
ITEM PART NO. QTY. DESCRIPTION
1 3001306
1 3001405
1 3002114
1 3002120
1 CHUTE HOUSING SUBASSEMBLY-STD CS
1 CHUTE HOUSING SUBASSEMBLY-EXT CS
1 CHUTE HOUSING SUBASSEMBLY STD SST
1 CHUTE HOUSING SUBASSEMBLY EXT SST
2 FPC007800075 1 COTTER PIN, 5/64 X 3/4
3 1420014
4 3004611
5 1420015
1 CLEVIS SHEAR PIN, 1/4 X 2-1/2
1 SPINNER DISC 11.5 DIA. POLY
3 CONTROL ROD
6 FPC013000100 1 COTTER PIN, 1/8 X 1
7
7
7
7
8 1420016
9 1420018
10
11
11
4
4
4
4
3
2
2
4
4
H. HEAD CAP SCREW 3/8-16 X 3/4 GR5
HEX NUT 3/8-16
3/8 FLATWASHER
3/8 LOCKWASHER
HAIRPIN COTTER, 3/32 X 2
LYNCH PIN, 3/8 X 1-3/4
GREASE FITTING #400
H. HEAD CAP SCREW, 3/8-16 X 3/4, GR5
3/8 FLATWASHER
ITEM PART NO.
11
12 1420101
13 1420150
13 142X150
14 KS301
15 1420004
16 1410711
17 3002225
141055K
141065K
QTY. DESCRIPTION
4 3/8 LOCKWASHER
2 PILLOW BLOCK BEARING, 3/4”
1 SPINNER SHAFT-STD
1 SPINNER SHAFT-EXT
1 KEY, 3/16” SQUARE X 1”
1 SPROCKET, 24 TOOTH W/ SET SCREW
1 ROLLER CHAIN, #40, W/ 80 LINKS
1 COLLAR, .75 DIA LOCK WITH TWO SET
SCREWS,3/16 KEYWAY
1 KIT,STD LG , SHAFT, BEARING,SPROCKET,
SPINNER DISK, & HDW
1 KIT EXT LG,SHAFT, BEARING, SPROCKET,
SPINNER DISK, & HDW
8
Quality since 1946
Repair Parts - engine Subassembly
ITEM PART NO. QTY. DESCRIPTION
5
6
7
8
1
2
3
4
1411902
1410709
1411911
9 1411915
10 KS402
11 1306070
12
13
14
1
1
1
2
2
2
4
1
1
2
1
4
4
4
STAND, ENGINE MOUNT
WASHER, LOCK, 5/16”
NUT, 5/16 SAE
WASHER, FLAT, 5/16”
SCREW, HHC, 5-16-18X 1.5 GR5
THROTTLE MOTOR ASSEMBLY
RETAINER, THROTTLE MOTOR BRKT
WASHER, FLAT, 1/4 SAE
SPROCKET, ENGINE DRIVE
KEY, 1/4” X 2”
SOLENOID
NUT, HEX, 1/4-20
WASHER, LOCK, 1/4”
SCREW, HHC, 1/4-20 X 3/4” GR 5
ITEM PART NO.
15 3005709
16 1411910
17 3001378
18 3001379
19 1401153
20 1430033
21
22
23
24 1410714
QTY.
1
1
1
2
1
2
3
3
1
DESCRIPTION
ENGINE, GAS 10 HP TECUMSEH
THROTTLE PIN ASSEMBLY
CABLE, BATTERY, 14” (BLACK)
CABLE, BATTERY, 14” (RED)
TERMINAL, 1/4” RING
TERMINAL, 5/16 RING
RED WIRE, 16 GA
SCREW, #8-32 X 5/8 MACHINE, PAN HD
NUT, #8-32 NYLOCK
BRACKET, THROTTLE CONTROL
TECUMSEH 10 HP
9
Quality since 1946
THRoTTle MoToR ASSeMblY
INSTRUCTIoNS
Caution! Improper installation of the Throttle Motor
Assembly can result in damage to the engine choke/throttle linkage.
Removal Instructions:
1.
Carefully observe the existing installation and mark the position of the Throttle Control Bracket on the Engine Mount
Stand.
2
.
Disconnect the wire connections.
3.
Remove the 1/4-20 fasteners that hold the Throttle
Control Bracket to the Engine Mount Stand. Remove the
Throttle Motor Assembly.
Installation Instructions:
1.
Connect the electrical wiring. Only connect the brown wire to brown (white) wire and red wire to red (black) wire.
2
.
Fasten the new Throttle Motor to the Throttle Control
Bracket using the existing hardware.
3.
Run the new Throttle Motor until the crank is within opening of the Throttle Control Bracket.
4.
Place the Throttle Pin Assembly on the crank of the
Throttle Motor using hole in the end of plastic block.
5.
Place the assembly onto the Engine Mount Stand by inserting the Throttle Pin into the engine choke/throttle linkage slider.
6.
Keeping the Throttle Pin Assembly parallel to the engine choke/throttle linkage bolt the assembly to the
Engine Mount Stand with the existing hardware.
7.
Run Throttle Motor in both directions until the slider in choke/throttle linkage stops against choke/throttle linkage bracket. Adjust position of Throttle Bracket if necessary.
Repair Parts - Drive Subassembly
ITEM PART NO. QTY. DESCRIPTION
5
6
7
7
8
9
10
11
3
4
1
1
2
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1411500
3005735
3000283
3005788
3005734
141070K
1401200
1410702
K18N
1401150
K18N
1411000
1411800
3005828
3005826
3001361
1410707
3001363
1410216
27
28 3001381
29 3000281
30
31
32
33
34
3000285
35 1412300
36 1413200
2
2
5
2
4
6
4
4
2
1
2
3
4
4
2
2
7
7
6
1
1
1
2
2
2
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
ENGINE MOUNT WELDMENT CS
ENGINE MOUNT WELDMENT SST
GEARBOX ASSEMBLY
GEARBOX, 20:1
SPROCKET, 16 TOOTH
KEY, WOODRUFF 1/4” x 1-1/8”
CLUTCH ASSEMBLY
KEY, WOODRUFF 1/4” x 1-1/8”
BEARING, 2-HOLE FLANGED, 1” ID
SPROCKET, CLUTCH, 52 TOOTH
ENGINE SHROUD WELDMENT CS
ENGINE SHROUD WELDMENT SST
WASHER, FLAT 3/8” ID NYLON
BATTERY, 12 VDC
BRACKET, BATTERY MOUNT
SPONGE RUBBER
SCREW, HHC 1/2-13 X 1 GR 5
WASHER, LOCK 1/2”
COLLAR, 1” ID
SCREW, HHC 5/16-18 X 1-1/2 GR 5
WASHER, FLAT 5/16 SAE
ENGINE ASSEMBLY, TECUMSEH 10 HP
PIN, PIVOT, 5/32 X 1-1/2”
SCREW, HHC 5/16 - 18 X 5/8”
BOLT, CARRIAGE 3/8-16 X 1”
WASHER, FLAT 3/8 USS
WASHER, LOCK 3/8”
NUT, HEX 3/8-16
NUT, HEX NYLOCK 3/8-16
SCREW, HHC 3/8-16 X 1-1/4” GR 5
WASHER, LOCK 5/16”
NUT, HEX 5/16-18
GUARD, ENGINE BASE CS
STRAP, RUBBER LATCH
WASHER, FLAT #8
E-RING, 5/32
SCREW, HHC 1/4-20 X 3/4 GR 5
NUT, NYLOCK 1/4-20
WASHER, FLAT 1/4” SAE
CHAIN, #40 ROLLER, 78 PITCHES
GROMMET, 1-1/2” RUBBER
10
Quality since 1946
11
Quality since 1946
Repair Parts - Drive Subassembly
ITEM PART NO. QTY. DESCRIPTION
1 1410200
2 1410250
3 1401100P
4 KS402
5 1410712
6 1410703
7 1411001
8 1410706
2 BEARING, 2 HOLE FLANGED, 1-1/8” ID
2 DRIVE SPROCKET, CAST
1 PINTLE CHAIN ASSEMBLY
2 KEY, 1/4” X 1/4” X 1-1/2”
1 DRIVE SHAFT
1 WELDMENT, IDLER TAKE-UP
2 BEARING, IDLER TAKE-UP
1 COUPLING
9 3002281
9 3002117
10
11
1 CHAIN GUARD CS
1 CHAIN GUARD SST
2 SET SCREW, 1/4-20 X 1/4”
4 WASHER, SPLIT LOCK, 3/8-16
12
13 1410305
4 NUT, 3/8-16 GR 5
4 SCREW- LEVELER, 3/8-16 X 1-1/4”
14 1410800 2 CLEVIS PIN, 3/8” X 2”
15 FPC013000100 2 COTTER PIN, 1/8” X 1”
16 141050W 2 WELDMENT, TAKE-UP BOLT
ITEM PART NO.
17
18
19
20
21 1410241
22
23 1410708
24 3002270B
3002270SS
25 3002269B
26
3002269SS
27
QTY. DESCRIPTION
5 SCREW, HHC, 1/4-20 X 1” GR 5
5 NUT, HEX 1/4-20 GR 5
5 WASHER, LOCK, 1/4”
2 NUT, HEX, 5/8-11 GR 5
1 WIPER BELT, HOPPER
5 WASHER, FLAT, 1/4”
1 WIRE HARNESS FOR HOPPER SPREADER
1 SILL EXTENTION R.H. 96” HOPPER
1 SILL EXTENTION R.H. SST
1 SILL EXTENTION L.H. 96” HOPPER
1 SILL EXTENTION L.H. SST
8 SCREW, BTN HD SOC CAP 1/2-13 X 3/4” ZN
8 SCREW, BTN HD SOC CAP 1/2-13 X 1” SST
8 NUT, HX FLNG 1/2-13 ZN
8 NUT, HX FLNG 1/2-13 SST
12
Quality since 1946
Repair Parts - Cab Control box Assembly
ITEM PART NO. QTY. DESCRIPTION
1410701
1 3002584
2 3002461
3
4 3002457
5
6
7 1430027
8 1430028
9 1430032
10 3002452
11 1430030
12 1430031
13
14 3002533
1
4
1
1
1
1
1
1
2
2
1
1
1
2
CAB CONTROL BOX
BOX BOTTOM
ASSEMBLY COVER
1/4” FLAT NYLON WASHER
BRACKET
1/4” FLAT WASHER
HEX HD CAP SCREW 1/4-20 X 1/2
CLUTCH SWITCH
THROTTLE SWITCH
IGNITION SWITCH
10 AMP CIRCUIT BREAKER
(4) TERMINAL JUMPER WIRE
(3) TERMINAL JUMPER WIRE
SCREW,8-32 X 3/8 PAN HD PHILLIPS
CONTROL BOX WIRE HARNESS
13
Quality since 1946
Repair Parts - feed Gate Assembly
ITEM PART NO. QTY. DESCRIPTION
1 1410108 1
1 1410108SS 1
2 1410109 1
2 1410109SS 1
3
3
4
4
5
5
1
1
6 141010W 1
6 141010WSS 1
1
1
2
2
FEED GATE LEVER
FEED GATE LEVER, SS
LEVER NUT
LEVER NUT, SS
BOLT CARRIAGE 3/8-16 X 1-1/4” ZN
BOLT CARRIAGE 3/8-16 X 1-1/4” SST
3/8 FLAT WASHER ZN
3/8 FLAT WASHER SST
3/8-16 HEX LOCKNUT ZN
3/8-16 HEX LOCKNUT SST
FEED GATE PANEL WELDMENT
FEED GATE PANEL WELDMENT, SS
14
Quality since 1946
Repair Parts - feed Gate Assembly
ITEM PART NO. QTY. DESCRIPTION
1 1499500 1
1 1499500SS
2
3
4
4
4
4
DEFLECTOR WELDMENT, CS
DEFLECTOR WELDMENT, SS
NUT, HEX 3/8-16 GR 5
SCREW, HHC, 3/8-16 X 1” GR 5
WASHER, SPLIT LOCK, 3/8”
15
Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
3005928 Rev A
