660-1120-0000-X2 1120RF-3000-BW-English
User's guide
Wireless programmable thermostat
(3000 W)
Technical Specifications
The installation of this thermostat should be made by a certified
electrician and must be installed in conformity with the national
and local Electrical Codes.
Operating voltage: 120/208/240 VAC, 60 Hz
Since you are a valuable customer, before starting
the installation of your new thermostat, please
make sure that the breakers for your heating system
are off at the main electrical panel!
0.5 A / 120 W @ 240 VAC
Compatible with an electric heating system such as:
Baseboard heater
Convector (short cycle)
Fan-forced convector (long cycle)
Note: The wires of this thermostat are non-polarized.
Remove your old
thermostat. It should be
connected on 2 wires. If
you have more than 2
wires, refer to our website
Minimum load:
The thermostat must be installed in
series with your heating device.
Connecting the thermostat directly
to the line voltage source will
damage the unit.
12.5 A / 3000 W @ 240 VAC
Resistive load only
Max. resistive load for this thermostat:
12.5 A / 3000 W @ 240 Vac
Unlock and lift
the thermostat cover.
Maximum load:
Setpoint range: 5 ˚C to 30 ˚C (41 ˚F to 86 ˚F)
Display range: 0 ˚C to 70 ˚C (32 ˚F to 158 ˚F)
Resolution: ± 0.5 ˚C (± 1 ˚F)
Storage: -20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Install your thermostat
Use the provided connectors to
connect the two wires of the
thermostat to the wires previously
connected to your old thermostat.
Power up the
Note: For a fan-forced
convector, go to the
''Advanced Settings'' section
to change the control cycle
of the thermostat.
Use the two screws to
secure the thermostat
to the electrical box.
Replace the
cover and lock.
Make sure to firmly tighten the wire connectors for a secure
connections. A loose connection can be a fire hazard.
Special CO/ALR solderless connectors must be used when
connecting with aluminum conductors.
Link your thermostat to your gateway
Initiate the connectivity
session by pressing the
button on the GT125.
On the thermostat
Connect to your network, the
wireless thermostat that is
closest to the GT125 by
pressing simultaneously
Flashes = Connecting
Remains lit = Connected
Stay connected
Sign in
Link your network
to neviweb®
Forgot your password
You don't have an account
Create your account and manage remotely
your network of devices.
To link your wireless
network to neviweb ,
refer to your GT125
Web gateway user's
nevi web
For more information, visit our website at:
All of the thermostat's settings can be set through the Web.
However, if you have not created your wireless network and
need to change the temperature format or the control cycle,
you need to:
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
If the connectivity fails,
an error message will
appear on the display.
Refer to our website to
troubleshoot the unit.
You have an account
Transmitter Module IC: 7693A-89XAM9A / FCC ID:OA3MRF89XAM9A
Get the setpoint to its minimum
and hold the
button for 3
seconds to access the menu.
Wait until the light flashes
green, indicating that new
devices can be added to
your network.
nevi web
Advanced Settings
button to change the setting.
Press the
button to select the next parameter.
For more information, visit our website at:
3-year limited warranty
Press the
Press and hold the
button for 3 seconds to exit the
menu and return to normal display.
Connect all your wireless
thermostats the same way, by
going to the next closest
When all the
thermostats are
connected, press
again on the
button of the GT125 to
close the connectivity
3 sec.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
Parameters & settings
Default Display
Control Cycle
SHRT (short cycle for electric baseboard)
FAN (long cycle for fan forced heater)
Temperature format
°C or °F
SINOPÉ TECHNOLOGIES INC. warrants the components of their
products against defects in material and workmanship for a 3 year
period from the date of purchase, under normal use and service, when
proof of purchase of such is provided to the manufacturer. This
warranty does not cover any transportation costs that may be incurred
by the consumer. Nor does it cover a product subjected to misuse or
accidental damage. The obligation of Sinopé Technologies Inc., under
the terms of this warranty, will be to supply a new unit and this releases
the manufacturer from paying the installation costs or other secondary
charges linked to replacing the unit or the components.
nevi web
660-1120-0000-X *NR
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF