Alpine CDA-9811R, CDA-9815RB, CDA-9812RR, CDA-9812RB, CDA-9813R Owner's manual

Alpine CDA-9811R, CDA-9815RB, CDA-9812RR, CDA-9812RB, CDA-9813R Owner's manual
PHONES
(044) 360-7-130
(050) 336-0-130
(063) 788-0-130
(067) 233-0-130
(068) 282-0-130
Internet store of
autogoods
ICQ
294-0-130
597-0-130
SKYPE
km-130
CAR RECEIVERS — Receivers • Media receivers and stations • Native receivers • CD/DVD changers • FM-modulators/USB adapters • Flash memory • Facia plates and adapters • Antennas • Accessories |
CAR AUDIO — Car audio speakers • Amplifiers • Subwoofers • Processors • Crossovers • Headphones • Accessories | TRIP COMPUTERS — Universal computers • Model computers • Accessories |
GPS NAVIGATORS — Portable GPS • Built-in GPS • GPS modules • GPS trackers • Antennas for GPS navigators • Accessories | VIDEO — DVR • TV sets and monitors • Car TV tuners • Cameras • Videomodules
• Transcoders • Car TV antennas • Accessories | SECURITY SYSTEMS — Car alarms • Bike alarms • Mechanical blockers • Immobilizers • Sensors • Accessories | OPTIC AND LIGHT — Xenon • Bixenon • Lamps
• LED • Stroboscopes • Optic and Headlights • Washers • Light, rain sensors • Accessories | PARKTRONICS AND MIRRORS — Rear parktronics • Front parktronics • Combined parktronics • Rear-view mirrors
• Accessories | HEATING AND COOLING — Seat heaters • Mirrors heaters • Screen-wipers heaters • Engine heaters • Auto-refrigerators • Air conditioning units • Accessories | TUNING — Vibro-isolation
• Noise-isolation • Tint films • Accessories | ACCESSORIES — Radar-detectors • Handsfree, Bluetooth • Windowlifters • Compressors • Beeps, loudspeakers • Measuring instruments • Cleaners • Carsits
• Miscellaneous | MOUNTING — Installation kits • Upholstery • Grilles • Tubes • Cable and wire • Tools • Miscellaneous | POWER — Batteries • Converters • Start-charging equipment • Capacitors
• Accessories | MARINE AUDIO AND ELECTRONICS — Marine receivers • Marine audio speakers • Marine subwoofers • Marine amplifiers • Accessories | CAR CARE PRODUCTS — Additives • Washer fluid •
Care accessories • Car polish • Flavors • Adhesives and sealants | LIQUID AND OIL — Motor oil • Transmission oil • Brake fluid • Antifreeze • Technical lubricant
In store "130" you can find and buy almost all necessary goods for your auto in
Kyiv and other cities, delivery by ground and postal services. Our experienced
consultants will provide you with exhaustive information and help you to chose
the very particular thing. We are waiting for you at the address
http://130.com.ua
R
FM/MW/LW/RDS CD Receiver
CDA-9815RB
CDA-9813R
CDA-9812RB
CDA-9812RR
EN
DE
a
.u
FM/MW/LW/RDS CD Receiver
CDA-9811R
m
o
.c
FR
0
3
1
• OWNER'S MANUAL
Please read before using this equipment.
• BEDIENUNGSANLEITUNG
Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes.
ES
• MODE D'EMPLOI
Veuillez lire avant d’utiliser cet appareil.
• MANUAL DE OPERACIÓN
Léalo antes de utilizar este equipo.
• ISTRUZIONI PER L’USO
Si prega di leggere prima di utilizzare il attrezzatura.
• ANVÄNDARHANDLEDNING
Innan du använder utrustningen bör du läsa igenom denna användarhandledning.
ALPINE ELECTRONICS MARKETING, INC.
1-1-8 Nishi Gotanda,
Shinagawa-ku,
Tokyo 141-0031, Japan
Phone 03-5496-8231
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
Phone 03-9769-0000
ALPINE ELECTRONICS GmbH
Kreuzerkamp 7,
40878 Ratingen, Germany
Phone 02102-4550
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
7300 Warden Ave., Suite 203, Markham,
Ontario L3R 9Z6, Canada
Phone 1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF U.K. LTD.
Alpine House
Fletchamstead Highway, Coventry CV4 9TW, U.K.
Phone 0870-33 33 763
ALPINE ELECTRONICS FRANCE S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris Nord Il,
B.P. 50016, 95945 Roissy Charles de Gaulle
Cedex, France
Phone 01-48638989
ALPINE ITALIA S.p.A.
Viale C. Colombo 8, 20090 Trezzano Sul
Naviglio (MI), Italy
Phone 02-484781
ALPINE ELECTRONICS DE ESPAÑA, S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava)-APDO 133, Spain
Phone 945-283588
Meiyi Printing Factory, Dalian, China
No. 28 Chang Qing Street, Xi Gang District, Dalian, China
Autogood products internet store http://130.com.ua
Designed by ALPINE Japan
Printed in China (Y)
68P02294K54-A
IT
SE
CHM-S630
CHA-1214
CHA-S634
• CD changer for CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• CD-Wechsler für CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• Changeur CD pour CDA-9815RB/CDA9813R/CDA-9812RB/CDA-9812RR/CDA9811R
• Cambiador de CD para
CDA-9815RB/CDA-9813R/CDA-9812RB/
CDA-9812RR/CDA-9811R
• Caricatore CD per CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• CD-växlare för CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• CD changer for CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• CD-Wechsler für CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• Changeur CD pour CDA-9815RB/CDA9813R/CDA-9812RB/CDA-9812RR/CDA9811R
• Cambiador de CD para
CDA-9815RB/CDA-9813R/CDA-9812RB/
CDA-9812RR/CDA-9811R
• Caricatore CD per CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
• CD-växlare för CDA-9815RB/CDA-9813R/
CDA-9812RB/CDA-9812RR/CDA-9811R
a
.u
Alpine CD Changers Give You More!
More musical selections, more versatility, more convenience.
The CHA-S634 is a high-performance 6-disc changer with a new M DAC, CD-R/RW PLAY BACK, MP3 PLAY BACK and CD TEXT.
The CHA-1214 Ai-NET model holds 12 discs, and the CHM-S630 M-Bus model is a super-compact 6-disc changer with a CD-R/RW
PLAY BACK.
m
o
.c
Von Alpine CD-Wechslern haben Sie mehr!
Mehr Musikauswahl, mehr Vielseitigkeit, mehr Komfort.
0
3
1
Der CHA-S634 ist ein Hochleistungs-Wechsler für 6 CDs mit dem neuen M-DAC, mit CD-R/RW- und MP3-Wiedergabefunktion und
mit CD-TEXT. Der CHA-1214 ist ein Ai-NET-Modell für 12 CDs. Der M-Bus-kompatible CHM-S630 ist ein superkompakter Wechsler
für 6 CDs mit CD-R/RW-Wiedergabefunktion.
Changeurs de CD Alpine : vous avez le choix!
Plus de sélections musicales, plus de souplesse, plus de confort.
Le modèle CHA-S634 est un changeur 6 disques ultra performant équipé des nouvelles fonctions M DAC, CD-R/RW PLAY BACK,
MP3 PLAY BACK et CD TEXT. Le modèle CHA-1214 Ai-NET contient 12 disques. Le modèle CHM-S630 M-Bus est un changeur 6
disques super compact doté de la fonction CD-R/RW PLAY BACK.
¡Los cambiadores Alpine de CD le ofrecen más!
Más selecciones musicales, más versatilidad y más ventajas.
CHA-S634 es un cambiador de seis discos de alto rendimiento con nuevo M DAC, CD-R/RW PLAY BACK, MP3 PLAY BACK y CD
TEXT. El modelo CHA-1214 Ai-NET alberga 12 discos y el modelo CHM-S630 M-Bus es un cambiador de seis discos de tamaño
reducido con un CD-R/RW PLAY BACK.
I caricatori CD Alpine danno di più!
Più scelta, più versatilità, più comodità.
Il modello CHA-S634 è un caricatore a 6 dischi ad elevate prestazioni dotato di un nuovo M DAC, CD-R/RW PLAY BACK, MP3 PLAY
BACK e CD TEXT. Il modello CHA-1214 Ai-NET è in grado di contenere 12 dischi, il modello CHM-S630 M-Bus è un caricatore a 6
dischi ultra compatto dotato di un CD-R/RW PLAY BACK.
Alpines CD-växlare ger mer!
Fler musikval, mer variation, större bekvämlighet.
CHA-S634 är en växlare för 6 skivor med mycket höga prestanda och en ny M D/A-omvandlare samt uppspelning av CD-R/RW, MP3
och CD TEXT. CHA-1214 Ai-NET rymmer 12 skivor. CHM-S630 M-Bus är en mycket kompakt växlare med kapaciteten 6 skivor med
uppspelning av CD-R/RW PLAY BACK.
Autogood products internet store http://130.com.ua
ENGLISH
Contents
The CDA-9812RX model that appears in this Manual represents the CDA-9812RB and
CDA-9812RR models.
CD/MP3/WMA
Operating Instructions
WARNING
WARNING .................................................. 3
CAUTION ................................................... 3
PRECAUTIONS ......................................... 3
Sound Setting
Getting Started
Turning Power On and Off ............................... 6
Initial System Start-Up ..................................... 6
Opening and Closing the Movable Display ...... 6
Display Tilt Adjustment .................................... 6
Adjusting Volume ............................................. 6
Lowering Volume Quickly
(CDA-9811R only) ........................................ 6
Changing the Audio Level Display Pattern
(CDA-9815RB/CDA-9813R/CDA-9812RX
only) ............................................................... 7
Detaching and Attaching the Front Panel ......... 7
Radio
Playback .......................................................... 13
Repeat Play ..................................................... 14
M.I.X. (Random Play) .................................... 14
Scanning Programmes .................................... 15
File/Folder Search (concerning MP3/WMA) ... 15
Quick Search ................................................... 15
About MP3/WMA .......................................... 15
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat ...... 17
Setting the Bass Control (CDA-9812RX/CDA9811R only) ................................................. 17
Setting the Treble Control (CDA-9812RX/CDA9811R only) .................................................. 18
Setting the Bass Type (CDA-9812RX/CDA9811R only) ................................................. 18
Adjusting the built-in Crossover
(CDA-9812RX/CDA-9811R only) .............. 18
Equalizer Presets
(CDA-9815RB/CDA-9813R only) .............. 18
Adjusting and Storing the Equalizer Curve
(CDA-9815RB/CDA-9813R only) .............. 19
Recalling the Stored Equalizer Curve
(CDA-9815RB/CDA-9813R only) .............. 19
About the Crossover
(CDA-9815RB/CDA-9813R only) .............. 19
Adjusting and Storing the Crossover Settings
(CDA-9815RB/CDA-9813R only) .............. 20
Recalling the Stored Crossover Settings
(CDA-9815RB/CDA-9813R only) .............. 21
About Time Correction ................................... 21
Bass Focus ...................................................... 22
Adjusting and Storing the Time Correction
(Storing available on CDA-9815RB/CDA9813R only) ................................................. 23
Recalling the Stored Time Correction
Settings (CDA-9815RB/CDA-9813R only) ... 23
Setting the MX Mode ..................................... 23
a
.u
m
o
.c
0
3
1
Listening to Radio ............................................. 8
Manual Storing of Station Presets .................... 8
Automatic Memory of Station Presets .............. 8
Tuning to Preset Stations .................................. 8
Station Title Search Function ............................ 9
Quick Search Function ...................................... 9
RDS
Setting RDS Reception Mode and Receiving
RDS Stations ................................................. 9
Recalling Preset RDS Stations ........................ 10
Receiving RDS Regional (Local) Stations ..... 10
PI SEEK Setting .............................................. 10
Receiving Traffic Information ........................ 10
PTY (Programme Type) Tuning ..................... 11
Receiving Traffic Information While Playing
CD or Radio ................................................. 11
Priority PTY (Programme Type) .................... 12
Displaying Radio Text .................................... 12
Windows Media, and the Windows logo are trademarks, or
registered trademarks of Microsoft Corporation in the United
States and /or other countries.
Autogood products internet store http://130.com.ua
1-EN
Other Functions
Displaying the Title/Text ................................. 24
Titling Discs/Stations ...................................... 25
Erasing Disc Title/Station Title ....................... 25
Blackout mode On and Off ............................. 25
i-Personalize™ Operation
(CDA-9815RB/CDA-9813R only)
About i-Personalize™ ..................................... 26
Data Downloading .......................................... 26
SETUP
Sound Customizing
Adjusting Source Signal Levels ...................... 27
Switching the Tuner Mode .............................. 27
Subwoofer On and Off .................................... 27
Setting the Subwoofer Output (CDA-9815RB/
CDA-9813R only) ....................................... 27
Sound (Beep) Guide Function ........................ 27
Visual Customizing
Changing Lighting Colour
(CDA-9813R only) ...................................... 27
Dimmer Control (CDA-9815RB/CDA-9813R/
CDA-9812RX only) .................................... 27
Scroll Setting ................................................... 27
Scroll Type Setting (CDA-9815RB only) ....... 28
Switching the Character Font
(CDA-9815RB only) ................................... 28
Adjusting Display Contrast
(CDA-9815RB only) ................................... 28
Demonstration ................................................. 28
Turning ON/OFF Traffic News
Announcement ............................................. 31
Setting the Announcement Select Mode ......... 31
Changing the Display Mode ........................... 31
Displaying the Regional Label ....................... 32
Receiving Announcement Information of DAB
Local Stations .............................................. 32
Setting for Automatic Change from
DAB to RDS ................................................ 32
Setting ON/OFF for DRC (Dynamic Range
Control) ....................................................... 32
MobileHub™ Link Operation
(Optional)
About MobileHub™ Link .............................. 33
Telephone Mode ON/OFF .............................. 33
Incoming Calls ................................................ 33
Calling ............................................................. 34
SMS (Short Message Service) Operation ....... 34
a
.u
Changer (Optional)
Controlling CD Changer (Optional) ............... 35
Playing MP3 Files with the CD Changer
(Optional) .................................................... 35
Multi-Changer Selection (Optional) ............... 35
m
o
.c
0
3
1
MP3
Playing MP3 Data ........................................... 28
External Device
Turning Mute Mode On/Off ........................... 28
Setting the AUX Mode (V-Link) ..................... 28
Connecting to an External Amplifier .............. 28
Setting Tone Defeat for External Devices ....... 28
DAB (Optional)
Using DAB Receiver for the Ensemble Seek
Tuning (Optional) ........................................ 29
Changing the Service ...................................... 29
Changing the Service Component .................. 29
Memorizing the Service .................................. 30
Receiving the Memorized Service .................. 30
Memorizing the Ensemble Automatically ...... 30
PTY (Programme Type) Tuning ..................... 30
2-EN
Remote Control
Controls on Remote Control (CDA-9815RB/
CDA-9813R/CDA-9812RX only) ............... 36
Operating the Audio Processor (CDA-9815RB/
CDA-9813R only) ....................................... 36
Battery Replacement (CDA-9815RB/CDA9813R/CDA-9812RX only) ......................... 37
Information
In Case of Difficulty ....................................... 37
Specifications .................................................. 39
Installation and Connections
Warning ........................................................... 40
Caution ............................................................ 40
Precautions ...................................................... 40
Installation ...................................................... 41
Connections for CDA-9812RX/CDA-9811R ... 42
Connections for CDA-9815RB/CDA-9813R ... 44
Autogood products internet store http://130.com.ua
Operating Instructions
WARNING
CAUTION
This symbol means important instructions. Failure
to heed them can result in injury or material
property damage.
WARNING
This symbol means important instructions. Failure
to heed them can result in serious injury or death.
DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR
ATTENTION AWAY FROM SAFELY DRIVING YOUR
VEHICLE.
Any function that requires your prolonged attention should only
be performed after coming to a complete stop. Always stop the
vehicle in a safe location before performing these functions.
Failure to do so may result in an accident.
KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL
HEAR OUTSIDE NOISE WHILE DRIVING.
Failure to do so may result in an accident.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS.
Failure to do so may cause personal injury or damage to the
product. Return it to your authorized Alpine dealer or the nearest
Alpine Service Centre for repairing.
DO NOT MIX NEW BATTERIES WITH OLD BATTERIES.
INSERT WITH THE CORRECT BATTERY POLARITY.
When inserting the batteries, be sure to observe proper polarity (+
and –) as instructed. Rupture or chemical leakage from the
battery may cause fire or personal injury.
KEEP FINGERS AWAY WHILE THE MOTORIZED FRONT
PANEL OR MOVING MONITOR IS IN MOTION.
a
.u
Failure to do so may result in personal injury or damage to the
product.
DO NOT DISASSEMBLE OR ALTER.
Doing so may result in an accident, fire or electric shock.
m
o
.c
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
30
PRECAUTIONS
Temperature
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Be sure the temperature inside the vehicle is between +60°C
(+140°F) and –10°C (+14°F) before turning your unit on.
Swallowing them may result in serious injury. If swallowed,
consult a physician immediately.
Moisture Condensation
1
USE THE CORRECT AMPERE RATING WHEN REPLACING
FUSES.
You may notice the CD playback sound wavering due to
condensation. If this happens, remove the disc from the player
and wait about an hour for the moisture to evaporate.
Failure to do so may result in fire or electric shock.
Damaged Disc
DO NOT BLOCK VENTS OR RADIATOR PANELS.
Doing so may cause heat to build up inside and may result in fire.
Do not attempt to play cracked, warped, or damaged discs.
Playing a bad disc could severely damage the playback
mechanism.
USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS.
Maintenance
Use for other than its designed application may result in fire,
electric shock or other injury.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Alpine dealer or the nearest Alpine Service
Station for servicing.
DO NOT PLACE HANDS, FINGERS OR FOREIGN OBJECTS
IN INSERTION SLOTS OR GAPS.
Doing so may result in personal injury or damage to the product.
Autogood products internet store http://130.com.ua
3-EN
PRECAUTIONS
Correct Handling
Never Attempt the Following
Do not grip or pull out the disc while it is being pulled back into
the player by the automatic reloading mechanism.
Do not attempt to insert a disc into the unit when the unit power
is off.
Do not drop the disc while handling. Hold the disc so you will
not leave fingerprints on the surface. Do not affix tape, paper, or
gummed labels to the disc. Do not write on the disc.
CORRECT
CORRECT
INCORRECT
Inserting Discs
Your player accepts only one disc at a time for playback. Do not
attempt to load more than one disc.
Make sure the label side is facing up when you insert the disc.
Your player will automatically eject any disc that is inserted
incorrectly. If the player continues to eject a correctly inserted
disc, push the RESET switch with a pointed object such as a
ballpoint pen.
Playing a disc while driving on a very bumpy road may result in
skips, but this will not scratch the disc or damage the player.
New Discs
Bumps
Fingerprints, dust, or soil on the surface of the disc could cause
the CD player to skip. For routine cleaning, wipe the playing
surface with a clean, soft cloth from the centre of the disc to the
outer edge. If the surface is heavily soiled, dampen a clean, soft
cloth in a solution of mild neutral detergent before cleaning the
disc.
a
.u
m
o
.c
As a protective measure to prevent the CD from jamming, the CD
player will automatically eject discs with irregular surfaces or
inserted incorrectly. When a new disc is inserted into the player
and ejected after initial loading, using your finger, feel around the
inside of the centre hole and outside edge of the disc. If you feel
any small bumps or irregularities, this could inhibit proper
loading of the disc. To remove the bumps, rub the inside edge of
the hole and outside edge of the disc with a ballpoint pen or other
such instrument, then insert the disc again.
Centre Hole
Disc Cleaning
0
3
1
Centre Hole
Disc Accessories
There are various accessories available on the market for
protecting the disc surface and improving sound quality.
However, most of them will influence the thickness and/or
diameter of the disc. Using such accessories can cause the disc to
be out of standard specifications and may create operational
problems. We recommend not using these accessories on discs
played in Alpine CD players.
New
Disc
Outside
(Bumps)
Transparent Sheet
Irregular Shaped Discs
Be sure to use round shape discs only for this unit and never use
any special shape discs.
Use of special shape discs may cause damage to the mechanism.
Installation Location
Make sure the CDA-9815RB/CDA-9813R/CDA-9812RX/CDA9811R will not be installed in a location subjected to:
•
•
•
•
Direct sun and heat
High humidity and water
Excessive dust
Excessive vibrations
4-EN
Autogood products internet store http://130.com.ua
Disc Stabilizer
On handling Compact Discs (CD/CD-R/CD-RW)
•
•
•
•
•
•
Do not touch the surface.
Do not expose the disc to direct sunlight.
Do not affix stickers or labels and do not write on the surface.
Clean the disc when it is dusty.
Make sure that there are no bumps around the disc.
Do not use commercially available disc accessories.
Do not leave the disc in the car or the unit for a long
time. Never expose the disc to direct sunlight. Heat
and humidity may damage the CD and you may not be
able to play it again.
To customers using CD-R/CD-RW
•
•
If a CD-R/CD-RW cannot be played back, make sure the last
recording session was closed (finalized).
Finalize the CD-R/CD-RW if necessary, and attempt playback
again.
About discs that can be used with the CDA-9815RB/CDA9813R/CDA-9812RX models.
Use only compact discs with the label side showing the CD logo
marks below.
•
•
a
.u
m
o
.c
If you use unspecified compact discs, correct performance cannot
be guaranteed.
You can play CD-Rs (CD-Recordable)/CD-RWs (CDReWritable) for audio use on this unit. You can also play CD-Rs/
CD-RWs containing MP3/WMA formatted audio files.
0
3
1
Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs on which a
recording failed or a re-recording was attempted, copyprotected CDs which do not conform to the audio CD
industry standard.
Use discs with MP3/WMA files written in a format
compatible with this unit. For details, see page 15-16.
About discs that can be used with the CDA-9811R model.
We recommend using only compact discs containing the marks
shown below.
You can play CD-Rs (CD-Recordable)/CD-RWs (CDReWritable) for audio use on this unit. You can not play CD-Rs/
CD-RWs containing MP3/WMA formatted audio files.
•
Some of the following CDs may not play on this unit:
Flawed CDs, CDs with fingerprints, CDs exposed to extreme
temperatures or sunlight (e.g., left in the car or this unit), CDs
recorded under unstable conditions, CDs not designed for
audio use, CDs on which a recording failed or a re-recording
was attempted.
Autogood products internet store http://130.com.ua
5-EN
Getting Started
Display Tilt Adjustment
Movable display
DISP/B.OUT (CDA-9815RB/CDA-9813R/
SOURCE/ CDA-9812RX)
RESET
POWER
MUTE/B.OUT (CDA-9811R)
The movable display may be adjusted to 3 different tilt angles
depending upon user preference.
Press TILT 98 to adjust the tilt angle of the movable
display.
Rotary encoder
TILT 98
• The display will close a half minute after the ignition key is turned
to the OFF position.
• The adjusted tilt angle of the display is stored in memory. There is
no need to re-adjust the tilt angle when the power is turned back on.
c
Caution
Keep hands (or any other object) away from the display while it is
opening or closing to avoid damage or injury. The back of the
movable display will get very warm under normal operating
conditions. This is not a malfunction. Do not touch.
Turning Power On and Off
Press SOURCE/POWER to turn on the unit.
• The unit can be turned on by pressing any other button except eject
c.
The volume level gradually increases to the previous level you
were listening to before the unit was turned off.
Adjusting Volume
a
.u
Turn the Rotary encoder until the desired sound is
obtained.
Press and hold SOURCE/POWER for at least 3
seconds to turn off the unit.
m
o
.c
• The first time power is turned on, the volume will start from level 12.
Lowering Volume Quickly (CDA-9811R only)
Initial System Start-Up
Activating the Audio Mute function will instantly lower the volume
level by 20 dB.
Be sure to press the RESET switch when using the unit for the first
time, after installing the CD changer, after changing the car battery, etc.
1
2
Turn off the unit power.
0
3
1
Press RESET with a ball-point pen or similar
pointed object.
Press MUTE/B.OUT to activate the MUTE mode.
The audio level will decrease by about 20 dB.
Pressing MUTE/B.OUT again will bring the audio back
to its previous level.
Opening and Closing the Movable Display
Press c.
The movable display will open.
To close the movable display, press c again.
The movable display will close.
• Do not apply shock to the movable display when it is open as it
may result in malfunction of the unit.
• The display may be dim during low temperatures and immediately
after turning on the power. The brightness will return to normal as
time elapses.
• The display will stop at the set tilt angle when closing.
Caution
Keep hands (or any other object) away from the display while it is
opening or closing to avoid damage or injury. The back of the
movable display will get very warm under normal operating
conditions. This is not a malfunction. Do not touch.
6-EN
Autogood products internet store http://130.com.ua
Changing the Audio Level Display Pattern
(CDA-9815RB/CDA-9813R/CDA-9812RX only)
You can select the Audio Level display from three display patterns.
You can also deactivate the display.
Press DISP/B.OUT to switch the display pattern.
For CDA-9815RB/CDA-9813R:
AUDIO ADJUSTMENT → EQ ADJUSTMENT → X-OVER
ADJUSTMENT → OFF → AUDIO ADJUSTMENT
Detaching and Attaching the Front Panel
Detaching
1
2
3
Turn off the unit power.
Press
(Release) at the upper left side until the
front panel pops out.
Grasp the left side of the front panel and pull it out.
For CDA-9812RX:
AUDIO ADJUSTMENT → BASS ADJUSTMENT → TREBLE
ADJUSTMENT → OFF → AUDIO ADJUSTMENT
The indicators show the value that is set in each mode as
shown below.
AUDIO
ADJUSTMENT
EQ/BASS/TREBLE
ADJUSTMENT
X-OVER
ADJUSTMENT
Level
Indicator
VOLUME
LEVEL
LEVEL
Width
indicator
BALANCE
WIDTH
SLOPE
Frequency
Indicator
FADER
FREQUENCY
FREQUENCY
Sub-W
Indicator
SUB-W∗
-
VOLUME : 18
BALANCE : L6
FADER
: F6
SUB-W
: 9dB
EQ Adjustment Display
Example for CDA-9813R
LEVEL
: +2
WIDTH
:2
Attaching
1
2
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
a
.u
Push the left side of the front panel until it locks
firmly into the main unit.
-
m
o
.c
∗Only when SUB-W is set to ON
AUDIO Adjustment Display
Example for CDA-9813R
• The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel.) This is not a
malfunction.
• To protect the front panel, place it in the supplied carrying case.
0
3
1
2
1
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides of the front panel
to avoid pushing buttons by mistake.
FREQUENCY: 200Hz
X-OVER Adjustment Display
Example for CDA-9813R
LEVEL
: -7dB
SLOPE
: 2 (-12dB/oct)
FREQUENCY : 2k
Autogood products internet store http://130.com.ua
7-EN
Radio
Manual Storing of Station Presets
1
SOURCE/
POWER
TUNE/
A.ME
BAND/
TEL.
Rotary encoder
2
Select the radio band and tune in a desired radio
station you wish to store in the preset memory.
Press and hold any one of the preset buttons
(1 through 6) that you want to store the station
on for at least 2 seconds.
The selected station is stored.
The display shows the band, preset no. and station
frequency memorized.
g
f
SEARCH
F/SETUP
Preset buttons
(1 through 6)
Listening to Radio
1
2
Press SOURCE/POWER until a radio frequency
appears in the display.
Automatic Memory of Station Presets
Press BAND/TEL. repeatedly until the desired
radio band is displayed.
1
FM1 (F1) → FM2 (F2) → FM3 (F3) → MW → LW → FM1 (F1)
3
Press TUNE/A.ME to select the tuning mode.
DX SEEK (Distance mode) → SEEK (Local mode) →
OFF (Manual mode) → DX SEEK
CDA-9813R/CDA-9812RX:
0
3
1
DX SEEK (Distance mode) → DX SEEK (Local mode) →
DX SEEK (Manual mode) → DX SEEK
CDA-9811R:
DX SEEK (Distance mode) → DX SEEK (Local mode) →
DX SEEK(Manual mode)→ DX SEEK
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
Press g or f to tune in the desired station.
Holding down g or f will change the frequency
continuously.
• The ST indicator appears on the display when a stereo FM station
is tuned in.
8-EN
2
a
.u
Press BAND/TEL. repeatedly until the desired
radio band is displayed.
Press and hold TUNE/A.ME for at least 2 seconds.
The frequency on the display continues to change while
the automatic memory is in progress. The tuner will
automatically seek and store 6 strong stations in the
selected band. They will be stored into buttons 1 to 6 in
order of signal strength.
When the automatic memory has been completed, the
tuner goes to the station stored in preset location no. 1.
m
o
.c
CDA-9815RB:
4
• A total of 30 stations can be stored in the preset memory (6 stations
for each band; FM1, FM2, FM3, MW and LW).
• If you store a station in a preset memory which already has a
station, the current station will be cleared and replaced with the
new station.
• If the “FUNC” indicator (only the underlined portion of the
“FUNC” indicator for CDA-9811R) is illuminated, turn off the
indicator by pressing F/SETUP, then you can perform the
operation.
• If no stations are stored, the tuner will return to the original station
you were listening to before the auto memory procedure began.
Tuning to Preset Stations
1
2
Press BAND/TEL. repeatedly until the desired
band is displayed.
Press any one of the station preset buttons (1
through 6) that has your desired radio station in
memory.
The display shows the band, preset number and
frequency of the station selected.
• If the “FUNC” indicator (only the underlined portion of the
“FUNC” indicator for CDA-9811R) is illuminated, turn off the
indicator by pressing F/SETUP, then you can perform the
operation.
Autogood products internet store http://130.com.ua
RDS
Station Title Search Function
If titles for radio stations are entered, you can search for a radio
station from its title.
.
1
Press SEARCH
Search mode.
BAND/
TEL.
in Radio mode to switch to Title
TITLE
The first title input blinks in the display.
2
3
Select the desired title by turning the Rotary
encoder within 10 seconds.
Press the Rotary encoder to receive the
frequency of the selected title.
• Search mode in Title Search mode is canceled by pressing and
holding SEARCH
for at least 2 seconds.
• If a station has no title, “NO TITLE” is displayed for 2 seconds.
g f
T.INFO
F/SETUP
1/AF
2/P.PTY
3/PTY
Setting RDS Reception Mode and Receiving
RDS Stations
Quick Search Function
You can search for a radio station by its frequency.
1
2
3
Press and hold SEARCH
for at least 2 seconds
in Radio mode to activate Quick Search mode.
Turn the Rotary encoder within 10 seconds to
select the desired frequency.
The RDS (Radio Data System) is a radio information system using
the 57 kHz subcarrier of regular FM broadcast. The RDS allows you
to receive a variety of information such as traffic information, station
names, and to automatically re-tune to a stronger transmitter that is
broadcasting the same programme.
1
• Search mode in Quick Search mode is canceled by pressing and
holding SEARCH
for at least 2 seconds.
30
1
a
.u
Press F/SETUP so that the “FUNC” indicator (only
the underlined portion of the “FUNC” indicator for
CDA-9811R) lights up.
m
o
.c
Press the Rotary encoder to receive the selected
frequency.
2
3
4
5
Press 1/AF to activate the RDS mode.
Press g or f to tune in the desired RDS
station.
Press 1/AF again to deactivate the RDS mode.
Press F/SETUP to activate the normal mode.
The “FUNC” indicator (only the underlined portion
of the “FUNC” indicator for CDA-9811R) goes out.
• When the unit receives the PTY31 (Emergency Broadcast)
signal, the unit will show “ALARM” in the display
automatically.
The RDS digital data includes the following:
PI
Programme Identification
PS
Programme Service Name
AF
List of Alternative Frequencies
TP
Traffic Programme
TA
Traffic Announcement
PTY
Programme Type
EON
Enhanced Other Networks
Autogood products internet store http://130.com.ua
9-EN
Recalling Preset RDS Stations
PI SEEK Setting
1
1
2
2
3
4
Press F/SETUP so that the “FUNC” indicator (only
the underlined portion of the “FUNC” indicator for
CDA-9811R) lights up.
Press 1/AF to activate the RDS mode.
Press F/SETUP to activate the normal mode.
The “FUNC” indicator (only the underlined portion
of the “FUNC” indicator for CDA-9811R) goes out.
Make sure that the “FUNC” indicator (only the
underlined portion of the “FUNC” indicator for
CDA-9811R) light goes out, then press the preset
button in which your desired RDS station is preset.
If the preset station's signal is weak, the unit automatically
searches and tunes to a stronger station in the AF
(Alternative Frequencies) list.
5
If the preset station and the stations in the AF list
cannot be received:
When the PI SEEK setting is on (refer to “PI SEEK Setting”
on this page), the unit searches again for a station in the
PI (Programme Identification) list.
If there are still no stations receivable in the area, the unit
displays the frequency of the preset station and the preset
no. disappears.
If the signal level of the Regional (Local) station being
tuned becomes too weak to receive, press the same
preset button to tune in a Regional station in other district.
1
2
3
0
3
1
Press and hold F/SETUP for at least 3 seconds to /
activate the setting mode.
Press g or f to select the RDS REG
(Regional) mode.
Press BAND/TEL. to turn on or off the RDS REG
(Regional) mode.
In the RDS REG OFF mode, the unit automatically keeps
receiving the related local RDS station.
4
4
Press g or f to select “PI SEEK”(CDA9811R:“PISK”).
Press BAND/TEL. to toggle the mode between “PI
SEEK ON” (CDA-9811R:“PISK ON”) and “PI SEEK
OFF” (CDA-9811R:“PISK OFF”).
Press F/SETUP to set the selected mode.
Receiving Traffic Information
1
2
Press T.INFO so that the underlined portion of the
“T.INFO” indicator lights up. (Only the upper lined
portion of the “T.INFO” indicator for CDA-9813R/
CDA-9812RX.)
Press g or f to select your desired traffic
information station.
a
.u
When a traffic information station is tuned in, the underlined
portion of the “TP” indicator (only the upper lined portion of
the “TP” indicator for CDA-9813R/CDA-9812RX) lights up.
Traffic information is heard only when it is being
broadcast. If traffic information is not being broadcast, the
unit is set in the standby mode. When a traffic information
broadcast begins, the unit automatically receives it and
the display shows “TRF-INFO” for a few seconds and
returns to the PS display.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
m
o
.c
• For presetting the RDS stations, refer to the Radio Operation
section. The RDS stations can be preset in the FM1, FM2 and FM3
bands only.
Receiving RDS Regional (Local) Stations
3
Press and hold F/SETUP for at least 3 seconds.
• If the traffic information broadcast signal falls below a certain
level, the unit remains in the receiving mode for 1 minute. If the
signal remains below a certain level for over 1 minute, the
underlined portion of the “T.INFO” indicator blinks. (Only the
upper lined portion of the “T.INFO” indicator for CDA-9813R/
CDA-9812RX.)
• If you do not want to listen to the traffic information being
received, lightly press T.INFO to skip that traffic information
message. The T.INFO mode will remain in the ON position to
receive the next traffic information message.
• If the volume level is changed while receiving traffic information,
the changed volume level will be memorized. When traffic
information is received next time, the volume level will be
automatically adjusted to the level memorized.
• In the T.INFO mode, the SEEK tuning selects only the TP stations.
Press F/SETUP to deactivate the setting mode.
10-EN
Autogood products internet store http://130.com.ua
PTY (Programme Type) Tuning
1
2
Press F/SETUP so that the “FUNC” indicator lights
up. (Only the underlined portion of the “FUNC”
indicator for CDA-9811R.)
Receiving Traffic Information While Playing
CD or Radio
1
Press 3/PTY to activate the PTY mode, while the
unit is in Radio (FM receiving) mode.
The Programme Type of the station being currently received
will be displayed for 5 seconds.
If there is no receivable PTY broadcast, “NO PTY” will be
displayed for 5 seconds.
If no RDS station can be received, the display shows “NO
PTY.”
2
Press g and f within 5 seconds after
activating the PTY mode to choose the desired
programme type while the PTY (programme type)
is being displayed.
When traffic information stations cannot be received:
In the tuner mode:
When the TP signal can no longer be received for over 1
minute, the underlined portion of the “T.INFO” indicator
(only the upper lined portion of the “T.INFO” indicator for
CDA-9813R/CDA-9812RX) blinks.
Each press scrolls the programme type by one.
LIGHT M ↔ CLASSICS ↔ OTHER M
4
Press 3/PTY within 5 seconds after selecting the
programme type to start searching for a station in
the selected programme type.
If no PTY station is found, “NO PTY” will be displayed for 5
seconds.
30
Press F/SETUP to activate the normal mode.
The “FUNC” indicator (only the underlined portion
of the “FUNC” indicator for CDA-9811R) goes out.
1
a
.u
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
m
o
.c
The chosen programme type display blinks during
searching and lights when a station is found.
5
Press g and f to select a traffic information
station if necessary.
When a traffic information broadcast starts, the unit
automatically mutes the CD player/changer or the regular
FM broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the
traffic information broadcast began.
• If no operation is performed within 5 seconds after pressing PTY,
the PTY mode will be automatically cancelled.
3
Press T.INFO so that the underlined portion of the
“T.INFO” indicator lights up. (Only the upper lined
portion of the “T.INFO” indicator for CDA-9813R/
CDA-9812RX.)
• Operate the unit while the “FUNC” indicator (only the underlined
portion of the “FUNC” indicator for CDA-9811R) lights up. If no
operation is performed within 5 seconds, the “FUNC” indicator
(only the underlined portion of the “FUNC” indicator for CDA9811R) goes out.
• The receiver is equipped with the EON (Enhanced Other
Networks) function in order to keep track of additional alternate
frequencies to the AF list. The underlined portion of the “EON”
indicator (only the upper lined portion of the “EON” indicator for
CDA-9813R/CDA-9812RX) lights up while an RDS EON station is
being received. If the station being received does not broadcast the
traffic information, the receiver automatically tunes in the related
station that broadcasts the traffic information when it occurs.
3
Press T.INFO to deactivate the Traffic Information
mode.
The underlined portion of the “T.INFO” indicator (only the
upper lined portion of the “T.INFO” indicator for CDA9813R/CDA-9812RX) goes out.
Autogood products internet store http://130.com.ua
11-EN
Priority PTY (Programme Type)
Displaying Radio Text
This function allows presetting of a programme type such as music
category, news, etc. You can listen to a programme in the preset
programme type as the unit automatically gives priority to the preset
programme type when it begins broadcasting, and interrupts the
programme you are currently listening. This feature is functional
when your unit is set to a mode other than the LW and MW.
Text messages from a radio station can be displayed.
1
2
Press F/SETUP so that the “FUNC” indicator (only
the underlined portion of the “FUNC” indicator for
CDA-9811R) lights up.
Press 2/P.PTY to activate the PRIORITY PTY
mode.
Press TITLE while receiving FM in the radio mode
to select the Radio Text display.
The display will change every time the button is pressed.
CDA-9815RB
PS (Programme
Service Name)
FREQUENCY
TITLE
FREQUENCY
“PRIO-PTY” is displayed for 2 seconds and then the
programme type for 3 seconds. The initial setting is
“NEWS.”
Press g or f within 5 seconds while “NEWS”
is being displayed to choose a desired programme
type. Then press 2/P.PTY.
PS (Programme
Service Name)
FREQUENCY
• If there is no receivable text message or the unit cannot receive a
text message properly, the display shows “NO TEXT.”
a
.u
m
o
.c
• In the PRIORITY PTY function, unlike in the T.INFO function, the
volume does not increase during operation.
0
3
1
Press F/SETUP to activate the normal mode. The
“FUNC” indicator (only the underlined portion of
the “FUNC” indicator for CDA-9811R) goes out.
• Operate the unit while the“FUNC” indicator (only the underlined
portion of the “FUNC” indicator for CDA-9811R) lights up.
If no buttons are pressed within 5 seconds, the “FUNC” indicator
(only the underlined portion of the “FUNC” indicator for CDA9811R) goes out.
12-EN
→
The display shows “WAITING” for a few seconds, then starts
scrolling the text message.
Press 2/P.PTY to activate the PRIORITY PTY mode
again.
To change the programme category, perform the step 3.
To disable the PRIORITY PTY function, press and hold
2/P. PTY for at least 2 seconds.
5
→
Radio Text
FREQUENCY
PS (Programme Service Name) → Radio Text → STATION
TITLE → FREQUENCY → PS (Programme Service Name)
The PRIORITY PTY function will activate.
4
→
CDA-9813R/CDA-9812RX/CDA-9811R
• If no operation is performed within 5 seconds after pressing
2/P.PTY, the PRIORITY PTY mode is automatically cancelled.
3
1
Autogood products internet store http://130.com.ua
3
CD/MP3/WMA
SOURCE/
POWER
-/J
Rotary
encoder
8
Press g or f to select the desired track (file).
Returning to the beginning of the current track (file):
Press g.
Fast backward :
Press and hold g.
SEARCH
Advancing to the beginning of the next track (file) :
Press f.
Fast forward :
Press and hold f.
g
f
9
4(
)
5(
)
6(
)
c
To customers who use CDA-9815RB/CDA-9813R/CDA9812RX:
MP3/WMA can be played back on the built-in CD
Player of this unit.
To customers who use CDA-9811R:
MP3 can be played back if an MP3 compatible CD
changer is connected. However, WMA cannot be played
back.
Press c.
2
Insert a disc with the label side facing up.
To pause playback, press -/J.
5
To eject the disc, press c.
Pressing -/J again will resume playback.
• Do not remove a CD during its eject cycle. Do not load more than
one disc at a time. A malfunction may result from doing either.
• If the CD does not eject, press and hold c for at least 3 seconds
with the movable display open.
• The CD-player can play discs containing audio data, MP3 data
and WMA data.
• The MP3 indicator is lit during MP3 playback.
• The WMA indicator is lit during WMA playback.
• The track display for MP3/WMA data playback is the file numbers
recorded on the disc.
• While playing back MP3/WMA, press 8 or 9 to move the folder
up or down.
a
.u
m
o
.c
Playback
1
4
The movable display will open.
0
3
1
The disc will be pulled into the unit automatically.
The movable display will close and playback will begin.
When a disc is already inserted, press SOURCE/POWER
to switch to the CD mode.
The mode will change every time the button is pressed.
TUNER → CD → CD CHANGER* → TUNER
* Only when the CD changer is connected
Autogood products internet store http://130.com.ua
13-EN
Repeat Play
M.I.X. (Random Play)
Press 4(
played.
Press 5(
) to play back repeatedly the track being
) in the play or pause mode.
The track (file) will be played repeatedly.
The tracks (files) on the disc will be played back in random
sequence.
Press 4(
To cancel M.I.X. play, press 5(
) again and select OFF to deactivate repeat play.
CD mode :
↓
M.I.X.:
RPT
: Only a file is repeatedly played back
↓ *1
RPT
: A disc is repeatedly played back
↓
(off)
↓
Track are played back in
random sequence.
*3
M.I.X.:The tracks on all the CDs in the current
magazine will be included in the random
playback sequence.
*1 When a CD changer is connected
• If REPEAT is set to ON during M.I.X. play in CD changer mode,
M.I.X. will apply to the current disc only.
↓
(off)
*3 When a CD changer equipped with the All M.I.X. function is
connected
MP3/WMA mode :
RPT
: Only a file is repeatedly played back
↓
RPT
: Only files in a folder are repeatedly played back
↓ *2
RPT
: A disc is repeatedly played back
↓
(off)
• If M.I.X. is set to ON during RPT
(REPEAT ALL) play in CD
changer mode, M.I.X. will apply to the current disc only.
a
.u
MP3/WMA mode :
↓
M.I.X.: Only files in a folder are played back in
random sequence.
↓
M.I.X.: Files are played back in random sequence.
If an MP3 compatible CD changer is
connected, all files in a disc are played back
in random sequence, and playback shifts to
the next disc.
↓
(off)
m
o
.c
*2 When an MP3 compatible CD changer is connected
• If a 6-disc CD changer or an MP3 compatible CD changer is
connected:
In CD changer mode, press F/SETUP to illuminate the “FUNC”
indicator (only underlined portions of the “FUNC” indicator are
illuminated for CDA-9811R), and go to the step above within 5
seconds.
• If a 12-disc CD changer is connected:
In CD changer mode, press F/SETUP twice to illuminate the
“FUNC” indicator (only underlined portions of the “FUNC”
indicator are illuminated for CDA-9811R), and go to the step
above within 5 seconds.
0
3
1
14-EN
) again.
CD mode :
• If a 6-disc CD changer or an MP3 compatible CD changer is
connected:
In CD changer mode, press F/SETUP to illuminate the “FUNC”
indicator (only underlined portions of the “FUNC” indicator are
illuminated for CDA-9811R), and go to the step above within 5
seconds.
• If a 12-disc CD changer is connected:
In CD changer mode, press F/SETUP twice to illuminate the
“FUNC” indicator (only underlined portions of the “FUNC”
indicator are illuminated for CDA-9811R), and go to the step
above within 5 seconds.
• A disc that contains more than 40 tracks may not be correctly
played back with the M.I.X. function on the CDA-9811R.
Autogood products internet store http://130.com.ua
Scanning Programmes
Press 6(
About MP3/WMA
) to activate the Scan mode.
The first 10 seconds of each track (file) will be played back in
succession.
To stop scanning, press 6(
mode.
) and deactivate the Scan
• If a 6-disc CD changer or an MP3 compatible CD changer is
connected:
In CD changer mode, press F/SETUP to illuminate the “FUNC”
indicator (only underlined portions of the “FUNC” indicator are
illuminated for CDA-9811R), and go to the step above within 5
seconds.
• If a 12-disc CD changer is connected:
In CD changer mode, press F/SETUP twice to illuminate the
“FUNC” indicator (only underlined portions of the “FUNC”
indicator are illuminated for CDA-9811R), and go to the step
above within 5 seconds.
File/Folder Search (concerning MP3/WMA)
1
4
3
Method for creating MP3/WMA files
m
o
.c
Select the desired file by turning the Rotary
encoder within 10 seconds.
Audio data is compressed by using MP3/WMA specified
software. For details on creating MP3/WMA files, refer to the
user's manual for that software.
MP3/WMA files that can be played back by this device have
the file extension “mp3” / “wma”. Files with no extension
cannot be played back. (WMA ver. 7.1 and 8 are supported)
Press the Rotary encoder to play back the
selected file.
0
3
1
Turn the Rotary encoder within 10 seconds to
select the desired folder.
Press the Rotary encoder to play back the first
file in the selected folder.
• Search mode is cancelled by pressing and holding SEARCH
for at least 2 seconds in Folder Search mode.
• While in Folder Search mode, press SEARCH
to switch to File
Search mode.
• “NO FILE” is displayed for 2 seconds if the folder that is selected
by the Folder Search mode contains no files.
• “– – – – – – – –” is displayed for the root folder (display
example: CDA-9811R).
Quick Search
2
Supported playback sampling rates and bit rates
MP3
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz, 22.05 kHz,
16 kHz, 12 kHz, 11.025 kHz, 8 kHz
Bit rates:
8 - 320 kbps
WMA
Sampling rates: 48 kHz, 44.1 kHz, 32 kHz, 24 kHz,
22.05 kHz
Bit rates:
32 - 192 kbps
Note that for sampling rates, this device’s frame display (Page
24) may not display correctly.
This device may not play back correctly depending on
sampling rates.
ID3 tags/WMA tags
This device supports ID3 tag v1 and v2, and WMA tag.
If tag data is in an MP3/WMA file, this device can display the
title (track title), artist name, and album name ID3 tag/WMA
tag data.
This device can only display single-byte alphanumeric
characters (up to 30) and the underscore. For non-supported
characters, “NO SUPPORT” (“NO SUPRT” for CDA-9811R) is
displayed.
Producing MP3/WMA discs
You can search for tracks (files).
1
MP3 files contain compressed audio data. MP3 encoding is
capable of compressing audio data at extremely high ratios,
reducing the size of music files to as much as one-tenth their
original size. This is achieved while still maintaining near CD
quality. The MP3 format realizes such high compression ratios
by eliminating the sounds that are either inaudible to the
human ear or masked by other sounds.
a
.u
Press 8 or 9 to select another Folder.
• File Search mode is cancelled by pressing and holding SEARCH
for at least 2 seconds.
• While in File Search mode, press SEARCH
to switch to Folder
Search mode.
2
MP3, whose official name is “MPEG Audio Layer 3,” is a
compression standard prescribed by the ISO, the International
Standardization Organization and MPEG which is a joint
activity institution of the IEC.
WMA, or “Windows Media™ Audio,” is compressed audio
data.
WMA allows you to create music files and store them at higher
ratios of compression than MP3 audio data (approx. half
original size). This is achieved while still maintaining CD
quality sound.
Press SEARCH
to select File Search mode or
Folder Search mode in MP3/WMA mode.
Folder Search mode
What is MP3?
What is WMA?
File Search mode
2
3
CAUTION
Except for private use, duplicating audio data (including MP3/
WMA data) or distributing, transferring, or copying it, whether for
free or for a fee, without permission of the copyright holder is
strictly prohibited by the Copyright Act and by international treaty.
Press and hold SEARCH
for at least 2 seconds
in the CD/Changer/MP3/WMA mode to activate
Quick Search mode.
Turn the Rotary encoder within 10 seconds to
select a desired track (file).
MP3/WMA files are prepared, then written to a CD-R or CDRW using CD-R writing software. A disc can hold up to 510
files/folders (including Root Folders).
Media supported
The media that this device can play back are CD-ROMs, CDRs, and CD-RWs.
The selected track is played back immediately.
• Search mode is cancelled by pressing and holding SEARCH
at least 2 seconds in Quick Search mode.
for
Autogood products internet store http://130.com.ua
15-EN
Corresponding File Systems
Terminology
This device supports discs formatted with ISO9660 Level 1 or
Level 2.
Under the ISO9660 standard, there are some restrictions to
remember.
The maximum nested folder depth is 8 (including the root
directory). File/folder names are limited to 31 characters
(including the extension), and are limited to 15 characters for
WMA.
Valid characters for folder/file names are letters A-Z (all
caps), numbers 0-9, and ‘_’ (underscore).
This device also can play back discs in Joliet, Romeo, etc.,
and other standards that conform to ISO9660. However,
sometimes the file names, folder names, etc., are not
displayed correctly.
Formats supported
This device supports CD-ROM XA, Mixed Mode CD,
Enhanced CD (CD-Extra) and Multi-Session.
This device cannot correctly play back discs recorded with
Track At Once or packet writing.
Bit rate
This is the “sound” compression rate specified for encoding. The
higher the bit rate, the higher the sound quality, but also the larger
the files.
Sampling rate
This value shows how many times per second the data is sampled
(recorded). For example, music CDs use a sampling rate of 44.1
kHz, so the sound is sampled (recorded) 44,100 times per second.
The higher the sampling rate, the higher the sound quality, but also
the larger the volume of data.
Encoding
Converting music CDs, WAVE (AIFF) files, and other sound files
into the specified audio compression format.
Tag
Song information such as track titles, artist names, album names,
etc., written into MP3/WMA files.
MP3: ID3 tag
WMA: WMA tag
Order of tracks
The unit plays the files in the order that the writing software
writes them. Therefore, the playing order may not be the same
as the order you input. The playback order of the folders and
files is as follows. However, the folder and file playback order
differs from the folder no. and file no. indicated on the display.
a
.u
1
m
o
.c
1
2
3
2
0
3
1
3
4
4
5
5
6
Folder
16-EN
MP3/WMA File
Autogood products internet store http://130.com.ua
Sound Setting
SOURCE/
POWER
Setting the Bass Control (CDA-9812RX/CDA9811R only)
BAND/
Rotary encoder
TEL.
Preset buttons
(1 through 6)
You can change the bass frequency emphasis to create your own tonal
preference.
1
Press CENTER f to select the Bass (bass centre
frequency) Control mode.
BASS → TREBLE → normal mode → BASS
2-1*2
g
MX
f
T.CORR/
X-OVER
EQ
(CDA-9815RB/CDA-9813R)
CENTER f
(CDA-9812RX/CDA-9811R)
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
1
60Hz ↔ 70Hz ↔ 80Hz ↔ 90Hz ↔ 100Hz ↔ 130Hz ↔ 150Hz
↔ 200Hz ↔ 60Hz
The displayed bass frequency is emphasized
2-2*2
Setting the bass band width (Q-Factor):
Press BAND/TEL. to select the desired bass band
width.
→ B. Width1 → B. Width2→ B. Width3 → B. Width4
(Narrow)← ...................................... →(Wide)
Press Rotary encoder repeatedly to choose the
desired mode.
Each press changes the modes as follows:
SUBWOOFER*1 → BALANCE → FADER → DEFEAT →
VOLUME → SUBWOOFER*1
a
.u
Changes the boosted bass band width to wide or narrow.
A wide setting will boost a wide range of frequencies
above and below the centre frequency. A narrower setting
will boost only frequencies near the centre frequency.
m
o
.c
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
2-3
Setting the bass level:
Turn the Rotary encoder to select the desired
bass level (–7~+7).
0
3
1
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
• If the Rotary encoder is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
• When setting the 2WAY/3WAY switch (page 44) to 3WAY, you
cannot adjust the FADER mode on the CDA-9815RB/CDA-9813R.
*1 When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
2
Setting the bass centre frequency:
Press g or f to select the desired bass centre
frequency.
Turn the Rotary encoder until the desired sound
is obtained in each mode.
By setting Defeat ON, previously adjusted settings of
BASS, TREBLE and EQ will return to the factory defaults
and MX is turned off.
You can emphasize or weaken the bass frequency.
• If no operation is performed within 15 seconds, the bass control
setting will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one
source are effective for all other sources (FM, MW (LW), CD etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, bass level is still adjustable if an
audio processor with the bass adjustment is connected.
• This function is inoperable when DEFEAT is set to ON.
*2 Selecting any of the “Setting the Bass Type” (TYPE 1 through 3),
temporarily replaces the custom settings you have made above.
• When you press DISP/B.OUT on the CDA-9812RX, you can switch
the level Indicator display to the BASS adjustment display. For
details, see “Changing the Audio Level Display Pattern” (page 7).
• Depending on the connected devices, some functions and display
indications do not work.
• When you press DISP/B.OUT, you can switch the Level Indicator
display to the AUDIO Adjustment display only on the CDA9815RB/CDA-9813R/CDA-9812RX. For details, see “Changing
the Audio Level Display Pattern” (page 7).
Autogood products internet store http://130.com.ua
17-EN
Setting the Treble Control (CDA-9812RX/CDA9811R only)
Adjusting the built-in Crossover
(CDA-9812RX/CDA-9811R only)
You can change the Treble Frequency emphasis to create your own
tonal preference.
The High and Low Pass Filters on this unit can be adjusted to suit
your personal taste.
1
Press CENTER f to select the Treble (treble centre
frequency) Control mode.
1
BASS → TREBLE → normal mode → BASS
HPF - <Press momentarily> → LPF* - <Press momentarily>
→ normal mode - <Press and hold for 2 seconds> → HPF
2-1
Setting the treble Centre frequency:
Press g or f to select the desired treble
centre frequency.
* When the subwoofer output of this unit is turned off, LPF and
phase are deactivated.
10.0kHz ↔ 12.5kHz ↔ 15.0kHz ↔ 17.5kHz ↔ 10.0kHz
The displayed Treble frequency is emphasized.
2
2-2
Setting the treble level:
Turn the Rotary encoder to select the desired
treble level (–7~+7).
• If no operation is performed within 15 seconds, the treble control
setting will be turned off automatically.
• The treble level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
Treble frequency settings adjusted for one source are effective for
all other sources (FM, MW (LW), CD, etc.).
• Depending on the connected devices, some functions and display
indications do not work. However, treble level is still adjustable if
an audio processor with the treble adjustment is connected.
• This function is inoperable when DEFEAT is set to ON.
• When you press DISP/B.OUT on the CDA-9812RX, you can switch
the level Indicator display to the TREBLE adjustment display. For
details, see “Changing the Audio Level Display Pattern” (page 7).
All frequencies above the selected cutoff are output.
2
LPF(Setting the Low Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies below the selected cutoff are output.
(Only available when using the subwoofer output from this
unit.)
a
.u
• If no operation is performed within 15 seconds, the setup menu
returns to normal mode.
• These functions are inoperative when an external, Ai-NET
processor is connected.
• The Bass and Treble controls effectiveness in modifying the sound,
depends on their settings and where the HPF and LPF are set.
• Except when the HPF and LPF is turned OFF, the subwoofer is in
monaural mode.
• When the subwoofer is set to OFF, LPF mode and change of phase
does not work.
m
o
.c
0
3
1
This function allows for 3 different bass type settings. Select the one
that appeals to you the most.
1
Press and hold CENTER f for at least 2 seconds to
set the bass type.
Press g or f within 15 seconds to select the
desired type (1 through 3).
Equalizer Presets (CDA-9815RB/CDA-9813R
only)
3 typical equalizer settings are preset at the factory for a variety of
musical source material.
1
2
TYPE 1 will sound best if you have a subwoofer in your
system. Use TYPE 2 or 3 if you are using small diameter
speakers.
3
• Bass centre frequency and bass band width previously set are
replaced when selecting TYPE 1 through 3. When bass type is set
to OFF, your previous settings are restored.
• Bass type is not selectable when connected to an external audio
processor.
• When you press DISP/B.OUT on the CDA-9812RX, you can switch
the level Indicator display to the BASS adjustment display. For
details, see “Changing the Audio Level Display Pattern” (page 7).
Press EQ and select the EQ mode.
Press either g or f.
With each press of the button, the equalizer mode will
display the selected equalizer characteristic.
FLAT(OFF) → POPS → ROCK → NEWS → FLAT(OFF)
FLAT
POPS
ROCK
NEWS
Press and hold CENTER f for at least 2 seconds to
return to normal mode.
18-EN
Press g or f to select the desired setting.
HPF (Setting the High Pass Filter):
FLAT (OFF) ↔ 80Hz ↔ 120Hz ↔160Hz
You can emphasize the treble frequency.
Setting the Bass Type (CDA-9812RX/CDA9811R only)
Press and hold T.CORR/X-OVER for at least 2
seconds.
: Flat frequency
: Emphasize midrange
: Emphasize lows and highs
: Boost midrange and suppress highs and lows
Selecting directly
Select the desired button (1 through 4).
[1]: FLAT(OFF)
[3]: ROCK
[2]: POPS
[4]: NEWS
3
Press EQ to return to normal mode.
• This function is inoperable when DEFEAT is set to ON (page 17).
• EQ mode is automatically cancelled if no operation is performed
within 15 seconds.
• When you press DISP/B.OUT, you can switch the Level Indicator
display to the EQ Adjustment display. For details, see “Changing
the Audio Level Display Pattern” (page 7).
Autogood products internet store http://130.com.ua
Adjusting and Storing the Equalizer Curve
(CDA-9815RB/CDA-9813R only)
About the Crossover
(CDA-9815RB/CDA-9813R only)
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
Crossover:
1
2
3
Press EQ to select the EQ mode.
Press and hold EQ for at least 2 seconds.
Press BAND/TEL. to select your desired
frequency band.
BAND1 → BAND2 → BAND3 → BAND4 → BAND5 → BAND1
The initial setting of each BAND is as follows.
Frequency
BAND1: 50 Hz, BAND2: 250 Hz, BAND3: 1.0 kHz,
BAND4: 3.2 kHz, BAND5: 10 kHz
This unit is equipped with an active crossover. The crossover limits
the frequencies delivered to the outputs. Each channel is controlled
independently. Thus, each speaker pair can be driven by the
frequencies for which they have been optimally designed.
The crossover adjusts the HPF (high pass filter) or LPF (low pass
filter) of each band, and also the slope (how fast the filter rolls off the
highs or lows).
Adjustments should be made according to the reproduction
characteristics of the speakers. Depending on the speakers, a passive
network may not be necessary. If you are unsure about this point,
please consult your authorized Alpine dealer.
2 way mode
Level
BAND1-5: ±0
Cut-off frequency
(1/3 octave steps)
Width (Q)
BAND1-5: 1
4
HPF
Adjustable frequency bands:
20Hz to 20kHz (in 1/3 octave steps)
5
6
----
20 Hz 200 Hz
----
FLAT, −6,
−12, −18,
−24 dB/
oct
0 to
−12 dB
Rear high
range
speaker
20 Hz 200 Hz
----
FLAT, −6,
−12, −18,
−24 dB/
oct
----
0 to
−12 dB
Front high
range
speaker
20 Hz 200 Hz
----
FLAT, −6,
−12, −18,
−24 dB/
oct
----
0 to
−12 dB
Turn the Rotary encoder to adjust the level.
To store the adjusted curve
1) Press and hold any one of the preset buttons (1
through 6) into which you wish to store the adjusted
curve for at least 2 seconds.
0
3
1
To set another channel, repeat steps 3 to 6.
a
.u
m
o
.c
Adjustable band width: 1, 2, 3.
7
8
LPF
Low range
speaker
Press SOURCE/POWER to select your desired
band width (Q).
After setting, press EQ to return to normal mode.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• EQ mode is automatically cancelled if no buttons are pressed
within 15 seconds.
• This function is inoperable when DEFEAT is set to ON (page 17).
• When you press DISP/B.OUT, you can switch the Level Indicator
display to the EQ Adjustment display. For details, see “Changing
the Audio Level Display Pattern” (page 7).
Level
HPF
Press g or f to select your desired
frequency.
LPF
Slope
Low range
High range
(Different from actual display)
Recalling the Stored Equalizer Curve
(CDA-9815RB/CDA-9813R only)
1
2
3
4
Press EQ to select EQ mode.
Press and hold EQ for at least 2 seconds.
Press any one of the preset buttons (1 through
6) to activate your desired curve.
Press EQ to return to normal mode.
• EQ mode is automatically cancelled if no operation is performed
within 15 seconds.
• This function is inoperable when DEFEAT is set to ON (page 17).
• If you do not adjust the factory settings of (FLAT/POPS/ROCK/
NEWS), the factory set display (FLAT/POPS/ROCK/NEWS) is
shown preferentially.
Autogood products internet store http://130.com.ua
19-EN
3 way mode
Cut-off frequency
(1/3 octave steps)
HPF
Low range
speaker
----
Mid range
speaker
20 Hz 200 Hz
High range
speaker
1 kHz 20 kHz
Slope
Level
LPF
HPF
LPF
----
FLAT, −6,
−12, −18,
−24 dB/
oct
0 to
−12 dB
FLAT, −6, FLAT, −6,
−12, −18, −12, −18,
−24 dB/ −24 dB/
oct
oct
0 to
−12 dB
20 Hz 200 Hz
20 Hz 20 kHz
----
Adjusting and Storing the Crossover
Settings (CDA-9815RB/CDA-9813R only)
−6, −12,
−18, −24
dB/oct
Before performing the following procedures, refer to “About the
Crossover” (Page 19).
1
2 WAY System
2
3
Mid range
Press g or f to select desired cut-off
frequency point (crossover point).
Adjustable frequency bands: 20Hz to 200Hz (in 1/3
octave steps)
4
Low range
Press BAND/TEL. to select desired parameter.
LOW (Subwoofer) → REAR → FRONT → LOW (Subwoofer)
0 to
−12 dB
----
Press and hold T.CORR/X-OVER for at least 2
seconds.
High range
5
Press SOURCE/POWER to select desired slope.
Adjustable slope: 0 (FLAT (OFF)), 1 (-6dB/oct), 2 (-12dB/
oct), 3 (-18dB/oct), 4 (-24dB/oct).
a
.u
Turn the Rotary encoder to select the desired
output level.
Adjustable output level: -12 to 0 dB.
To store the adjusted contents
1) Press and hold any one of the preset buttons (1
through 6) for at least 2 seconds into which you wish to
store the adjusted contents.
m
o
.c
(Different from actual display)
Level adjusting
(0 to - 12 dB)
Output frequency range
0
3
1
Slope FLAT
Slope adjusting
20 Hz
HPF cut-off
frequency
(Different from actual display)
LPF cut-off
frequency
• HPF (high pass filter): Cuts the lower frequencies and allows the
higher frequencies to pass.
• LPF (low pass filter): Cuts the higher frequencies and allows the
lower frequencies to pass.
• Slope: The level change (in dB) for a frequency change of one
octave.
• The higher the slope value, the steeper the slope becomes.
• Adjust the slope to FLAT to bypass the HP or LP filters.
• Do not use a tweeter without the HPF on or set to a low frequency,
as it may cause damage to the speaker due to the low frequency
content.
• You cannot adjust the crossover frequency higher than the HPF or
lower than the LPF.
• Adjustment should be made according to the recommended
crossover frequency of the connected speakers. Determine the
recommended crossover frequency of the speakers. Adjusting to a
frequency range outside that recommended may cause damage to
the speakers.
For the recommended crossover frequencies of Alpine speakers,
refer to the respective Owner's Manual.
We are not responsible for damage or malfunction of speakers
caused by using the crossover outside the recommended value.
20-EN
6
7
For setting another channel, repeat the steps 2 to
5.
After setting, press T.CORR/X-OVER to return to
normal mode.
• Crossover mode is automatically cancelled if no operation is
performed within 15 seconds.
3 WAY System
2
Press BAND/TEL. to select desired parameter.
LOW → MID-L → MID-H → HIGH (HI) → LOW
3
Press g or f to select desired cut-off
frequency point (crossover point).
Adjustable frequency bands:
LOW
MID-L
MID-H
HIGH
4
: 20Hz to 200Hz (in 1/3 octave steps)
: 20Hz to 200Hz (in 1/3 octave steps)
: 20Hz to 20kHz (in 1/3 octave steps)
: 1kHz to 20kHz (in 1/3 octave steps)
Press SOURCE/POWER to select the desired
slope.
Adjustable slope: 0 (FLAT* (OFF)), 1 (-6dB/oct), 2 (-12dB/
oct), 3 (-18dB/oct), 4 (-24dB/oct).
* FLAT cannot be set for the HIGH slope.
5
Turn the Rotary encoder to select the desired
output level.
Adjustable output level: -12 to 0 dB.
Autogood products internet store http://130.com.ua
To store the adjusted contents
1) Press and hold any one of the preset buttons (1
through 6) for at least 2 seconds into which you wish to
store the adjusted contents.
6
7
For setting another channel, repeat the steps 2 to
5.
5.1ms
After setting, press T.CORR/X-OVER to return to
normal mode.
0.5m
2.25m
• About the 2way/3way system
You can switch to 2way/3way system mode with the 2way/3way
switch on the side of the unit (page 44).
*1
*1
When setting to “3 WAY ”:
The unit can be operated in a 3 way system.
F/R Sub. W
3WAY
When setting to “F/R/Sub.W ”:
The unit can be operated in a 2 way system.
• Crossover mode is automatically cancelled if no operation is
performed within 15 seconds.
• When you press DISP/B.OUT, you can switch the level Indicator
display to the X-OVER adjustment display. For details, see
“Changing the Audio Level Display Pattern” (page 7).
Recalling the Stored Crossover Settings
(CDA-9815RB/CDA-9813R only)
1
2
3
*1 Subwoofer speaker.
CDA-9812RX/CDA-9811R only
You cannot change the Time Correction value for the subwoofer, but
you can set the subwoofer's apparent position to the front by
adjusting the Time Correction value of the front and rear speakers.
For details, refer to the “ *1 ” on page 22.
The sound is not balanced because the distance between the
listening position and the various speakers is different.
The difference in distance between the front left speaker and
the rear right speaker is 1.75 m (68-7/8").
a
.u
Here we calculate the time correction value for the front left
speaker in the diagram on the above.
m
o
.c
Press and hold T.CORR/X-OVER for at least 2
seconds.
Conditions:
Farthest Speaker – listening position : 2.25 m (88-9/16")
Front left speaker – listening position : 0.5 m (19-11/16")
Calculation: L = 2.25 m – 0.5 m = 1.75 m (68-7/8")
Time correction = 1.75 ÷ 343*2 × 1000 = 5.1 (ms)
Press any one of the preset buttons (1 through
6) that has your desired crossover settings in
memory.
30
1
Press T.CORR/X-OVER to return to normal mode.
• Crossover mode is automatically cancelled if no operation is
performed within 15 seconds.
About Time Correction
The distance between the listener and the speakers in a car vary
widely due to the complex speaker placement. This difference in the
distances from the speakers to the listener creates a shift in the sounds
image and frequency characteristics. This is caused by the time delay
between the sound reaching the listener’s right versus the left ear.
To correct this, the CDA-9815RB/CDA-9813R/CDA-9812RX/CDA9811R is able to delay the audio signal to the speakers closest to the
listener. This effectively creates a perception of increased distance for
those speakers. The listener can be placed at an equal distance
between the left and right speakers for optimum staging.
The adjustment will be made for each speaker in 0.1 ms steps.
Example 1. Listening Position: Front Left Seat
*2 Speed of sound: 343 m/s (765 mph) at 20˚C
In other words, giving the front left speaker a time correction
value of 5.1 ms makes it seem as if its distance from the
listener is the same as the distance to the farthest speaker.
Time correction eliminates the differences in the time required
for the sound to reach the listening position.
The time of the front left speaker is corrected by 5.1 ms so that
its sound reaches the listening position at the same time as the
sound of other speakers.
Example 2. Listening Position: All Seats
Adjust the time correction level of each speaker to almost the same
level.
1
2
Adjust the time correction level of the front left speaker
to a high value and the rear right to zero or a low value.
Sit in the listening position (driver’s seat, etc.) and
measure the distance (in meters) between your
head and the various speakers.
Calculate the difference between the distance to the
farthest speaker and the other speakers.
L = (distance to farthest speaker) – (distance to other
speakers)
3
Divide the distances calculated for the speakers by
the speed of sound (343 m/s (765 mph) at 20˚C).
These values are the time correction values for the
different speakers.
Autogood products internet store http://130.com.ua
21-EN
Bass Focus
The time difference between the front-rear/left-right speakers, can be
adjusted at the same time. With an initial delay of 0.1 ms for each of
the 0 to 99 steps, audible time correction can be done.
1
Press T.CORR/X-OVER to select the Bass Focus
mode.
(2) Press BAND/TEL. to select the left (front and rear)
speakers. Then turn the Rotary encoder to select
1.5 ms (Delay no. 15 in the table). The time
difference is 3.0 ms*2 for the front left speaker, and
1.5ms for the left rear speaker, creating the
impression of an equal listening between the front
left speaker and the other speakers.
Bass Focus mode → Time correction mode → normal mode
→ Bass Focus mode
2
3.0ms
Press BAND/TEL. to select the speakers to be
adjusted (see below).
→
FL
FR
RL
RR
→
FL
FR
RL
RR
1.5ms
1.5ms
1.5ms
1.5ms
*1
Front (left-right)
speakers
FL
FR
RL
RR
Left (front-rear)
speakers
←
Rear (left-right)
speakers
3
4
5
FL
FR
RL
RR
←
a
.u
m
o
.c
Right (front-rear)
speakers
Turn the Rotary encoder to adjust the delay (see
Time Difference Table).
30
To set another channel (speakers), repeat steps 2
and 3.
1
*1 Subwoofer speaker.
CDA-9812RX/CDA-9811R only
Delay (turn the rotary encoder) the audio signal to the front (left
and right) speakers to make the apparent position of the subwoofer
to be at the front. In doing this, the apparent position between the
front (left and right) speakers and subwoofer will appear equal to
the driver. After performing the above, you can change the
positions of the left and right speakers by delaying the time .
*2 Because the time difference was already set to 1.5ms for the front
left speaker to begin with, the additional correction of 1.5ms makes
the total time difference of the front left speaker 3.0ms.
After setting, press and hold T.CORR/X-OVER for
at least 2 seconds to return to normal mode.
• Any manual time correction adjustments will also affect
corrections made in Bass Focus.
• Bass Focus mode is automatically cancelled if no operation is
performed within 15 seconds.
Example setting for steps 2 and 3
(1) Press BAND/TEL. to select the front (left and
right) speakers. Then turn the Rotary encoder to
select 1.5 ms (Delay no. 15 in the table). The time
difference is 1.5 ms for both front (left and right
speakers.
Time Difference Table
Delay
Number
Time
Difference
(ms)
Delay
Number
Time
Difference
(ms)
Delay
Number
Time
Difference
(ms)
0
0.0
14
1.4
28
2.8
1
0.1
15
1.5
29
2.9
2
0.2
16
1.6
30
3.0
3
0.3
17
1.7
31
3.1
4
0.4
18
1.8
32
3.2
5
0.5
19
1.9
33
3.3
6
0.6
20
2.0
34
3.4
7
0.7
21
2.1
35
3.5
8
0.8
22
2.2
36
3.6
9
0.9
23
2.3
37
3.7
10
1.0
24
2.4
38
3.8
11
1.1
25
2.5
39
3.9
12
1.2
26
2.6
40 - 98
4.0 - 9.8
13
1.3
27
2.7
99
9.9
1.5ms
1.5ms
*1
22-EN
Autogood products internet store http://130.com.ua
Adjusting and Storing the Time Correction
(Storing available on CDA-9815RB/CDA-9813R
only)
Before performing the following procedures, refer to “About Time
Correction” (page 21).
1
Press T.CORR/X-OVER to make time corrections.
Setting the MX Mode
MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The radio, CD, and MP3, will be able
to reproduce the music clearly even in cars with a lot of road noise.
1
2
Each press changes the mode as follows:
2
Bass Focus mode → Time Correction mode → normal mode
→ Bass Focus mode
3
Press BAND/TEL. to select a speaker to be
adjusted.
4
CDA-9815RB/CDA-9813R
F–L→F–R→R–L→R–R→S–L→S–R→F–L
CDA-9812RX/CDA-9811R
F–L→F–R→R–L→R–R→F–L
3
Turn the Rotary encoder to adjust the desired
time correction value.
To store the adjusted contents (CDA-9815RB/CDA-9813R only)
1) Press and hold any one of the preset buttons (1
through 6) for at least 2 seconds into which you wish to
store the adjusted contents.
4
5
Repeat step 2 and 3 to set another speaker.
0
3
1
Recalling the Stored Time Correction
Settings (CDA-9815RB/CDA-9813R only)
Press T.CORR/X-OVER to make time corrections.
Each press changes the mode as follows:
Bass Focus mode → Time Correction mode → Normal mode
→ Bass Focus mode
2
3
Press SOURCE/POWER to select the source to
which you want to apply MX (Media Xpander).
Press and hold MX for at least 2 seconds to
activate the level setting mode.
Turn the Rotary encoder to select your preferred
level or OFF.
FM (MX level 1 to 3):
The medium to high frequencies become clearer, and
produces well balanced sound at all frequencies.
CD (MX level 1 to 3):
CD mode processes a large quantity of data. This data
processing power takes advantage of CD quality sound
sources.
MP3/WMA/DAB (MX level 1 to 3):
This corrects information that was lost at the time of
compression. This reproduces a well-balanced sound close to
the original.
a
.u
DVD (Video CD)
(MOVIE MX level 1 to 2):
The dialogue portion of a video is reproduced more clearly.
m
o
.c
After setting, press and hold T.CORR/X-OVER for
at least 2 seconds to return to normal mode.
• If no operation is performed in 15 seconds, the unit returns to
normal mode.
1
Press MX to select MX ON.
Press the preset button (1 through 6) that has
your desired time correction in memory.
Press and hold T.CORR/X-OVER for at least 2
seconds to return to normal mode.
• Time Correction mode is automatically cancelled if no operation is
performed within 15 seconds.
(MUSIC MX level 1):
A DVD or Video CD contains a large quantity of data such as
music clip. MX uses this data to reproduce the sound
accurately.
AUX (MX level 1):
Choose the MX mode (MP3, MUSIC, or MOVIE) that
corresponds to the media connected.
If two external devices are connected, a different MX
mode for each media can be selected.
5
Press Rotary encoder to return to normal mode.
• To cancel MX mode for all music sources, press MX to turn MX off.
• MX mode is automatically cancelled if no operation is performed
within 15 seconds.
• Each music source, such as radio, CD, and MP3/WMA can have its
own MX setting.
• On disks with both MP3/WMA and CD-DA, when the source
changes from “MP3/WMA to CD-DA” or “CD-DA to MP3/
WMA”, MX-mode switching may delay playback slightly.
• Setting to MX OFF sets MX mode of each music source to OFF.
• This function is inoperable when DEFEAT is set to ON.
• MX mode does not function when MX is set to ON for MW, LW
radio.
• If the unit is connected to an audio processor with the MX function,
such as PXA-H700, etc., the MX processing can be applied to the
audio processor. In this case the audio processor needs to be
adjusted. For details, refer to the Owner’s Manual of the audio
processor.
• When entering RDS signals, the MX operation cannot be
performed.
Autogood products internet store http://130.com.ua
23-EN
The display in MP3/WMA mode (MP3 files can be played back
with the CDA-9811R model if an MP3 compatible changer is
connected):
CDA-9815RB
Other Functions
DISP/B.OUT (CDA-9815RB/CDA-9813R/CDA-9812RX)
MUTE/B.OUT (CDA-9811R)
-/J
TITLE
FOLDER NO./
FILE NO.
ELAPSED TIME
BAND/TEL.
→
FOLDER NAME*5
→
FILE NAME
FILE NAME
TRACK NAME*3
ARTIST NAME*3
→
→
→
TRACK NAME*3
ARTIST NAME*3
ALBUM NAME*3
ALBUM NAME*3
FOLDER NO./FILE NO.
→
FRAME*4
ELAPSED TIME
g
f
CDA-9813R/CDA-9812RX/CDA-9811R
FILE NO./ELAPSED TIME → FOLDER NO./FILE NO. →
FOLDER NAME*5 → FILE NAME → TRACK NAME*3 →
ARTIST NAME*3 → ALBUM NAME*3 → FRAME*4 → FILE NO./
ELAPSED TIME
Rotary encoder
Displaying the Title/Text
It is possible to display the CD/Station title if the title has been
previously inputted (“Titling Disc/Stations” page 25). Text
information, such as the disc name and the track name, will be
displayed if playing a CD text compatible disc. It is also possible to
display the folder name, the file name, and the tag, etc., while playing
MP3/WMA files.
Press TITLE.
The display in Radio mode:
CDA-9815RB
*1
TITLE
FREQUENCY
→
Radio Text
FREQUENCY
→
0
3
1
PS (Programme Service Name)
FREQUENCY
a
.u
m
o
.c
The display will change every time the button is pressed.
PS (Programme Service Name)
→
FREQUENCY
*1 TITLE can be input or erased.
*2 Displayed during playback of a disc with CD Text.
“NO TEXT” will be displayed when the CD contains no Text data.
*3 ID3 tag/WMA tag
If an MP3/WMA file contains ID3 tag/WMA tag information, all
the ID3 tag/WMA tag information is displayed (e.g., track name,
artist name, and album name). All other tag data is ignored.
“NO DATA” will be displayed when an MP3/WMA file contains no
ID3 tag/WMA tag information.
*4 The recording sampling rate and bit rate of the MP3/WMA file are
displayed.
*5 “– – – – – – – –” is displayed for the folder name of the root
folder (display example: CDA-9811R).
About the indicator display
When displaying Title/Text, the following indicators are lit
according to the mode.
This indicator is constantly lit.
CDA-9815RB
CDA-9813R/CDA-9812RX/CDA-9811R
PS (Programme Service Name) → Radio Text → TITLE →
FREQUENCY → PS (Programme Service Name)
1 23 45
The display in CD mode (Text is displayed for the CDA-9811R
model when a compatible changer with CD text is connected):
CDA-9815RB
TRACK NO./
ELAPSED TIME
TEXT
(DISC NAME)∗2
TEXT
TEXT
(TRACK NAME)∗2
(DISC NAME)∗2
→
→
TEXT
TITLE
(TRACK NAME)∗2
This indicator shows the strength
of the telephone signal.
CDA-9813R/CDA-9812RX
This indicator is
constantly lit.
These indicators are lit in order of
radio frequency or track number
being played.
*1
TITLE
→
TRACK NO./
ELAPSED TIME
→
TRACK NO./
ELAPSED TIME
TEXT
(DISC NAME)∗2
1 2 34 5 6
CDA-9813R/CDA-9812RX/CDA-9811R
TRACK NO./ELAPSED TIME → TEXT (DISC NAME)*2 → TEXT
(TRACK NAME)*2 → TITLE → TRACK NO./ELAPSED TIME
This indicator shows the strength of the
telephone signal.
123456
CDA-9811R
24-EN
6
This indicator is constantly lit.
Autogood products internet store http://130.com.ua
Indicator/
Mode
1
2
3
4
5
6
CD Mode
While
displaying Title
MP3/WMA
Mode
TUNER Mode
—
—
While
displaying
Folder Name
While
—
displaying File
Name
While
—
displaying
Artist Name∗
While
While
displaying Text displaying
(Disc Name)
Album Name∗
While
While
displaying Text displaying
(Track Name) Track Name∗
—
—
—
While
displaying Title
∗Tag information
About “Title” and “Text”
Title:
With this device, it is possible to input the CD/Station name
(this page). This inputted name is referred to as a “title.”
You cannot input or display titles on MP3/WMA discs.
Text:
Text compatible CDs contain text information such as the disc
name and track name. Such text information is referred to as
“text.”
30
It is possible to title your favourite CD's or radio stations.
You cannot input titles on MP3/WMA discs.
1
2
Press TITLE and select the Title Display.
For details, see “Displaying the Title/Text” (page 24). For
CDA-9815RB, see asterisk 1 of “Displaying the Title/Text”
(page 24).
Press and hold TITLE for at least 3 seconds. The
first character will blink.
CDA-9815RB only
Press BAND/TEL. to select the characters/
symbols.
Upper case → Lower case → Numeral/Symbol
→ Upper case
3
4
Pressing the Rotary encoder after entering the 8th
character automatically stores the title into memory.
6
Press TITLE to record the title.
• If you cancel while entering a title, selected characters are not
written.
• You can enter 24 radio station titles and 18 CD titles on this unit. If
you try to store beyond the limit, the display will show “FULL
DATA.” At this point, no more titles can be stored. To input a new
title, one of the previously inputted titles must first be deleted.
• The CD Changer title length or memory capacity varies depending
upon the model being used.
• When you want to erase a title, enter the “ ” (“ ” for CDA9815RB) symbol into all spaces.
• The operations described in steps 3 to 5 must be made within 10
seconds. The input mode will be cancelled if no action is taken for
over 10 seconds.
Erasing Disc Title/Station Title
1
a
.u
Press TITLE to select the Title Display. Then, press
again and hold for at least 3 seconds.
• For CDA-9815RB, see asterisk 1 of “Displaying the Title/Text”
(page 24).
m
o
.c
• Some characters may not be displayed correctly with this device,
depending on the character type.
• The CD changer must also be CD Text compatible for the Text
information to be displayed.
• When the Scroll Setting (page 27) is set to “SCROLL MANUAL,”
press and hold TITLE for at least 3 seconds to scroll the Text
information only once (TEXT DISPLAY, FOLDER NAME
DISPLAY, FILE NAME DISPLAY or TAG DISPLAY mode).
• “NO SUPPORT” (“NO SUPRT” for CDA-9811R) is displayed
when the desired text information cannot be displayed on this unit.
• If the title was not previously input, “NO TITLE” is displayed.
1
Repeat steps 3 and 4 above to complete the titling.
When entering a title of less than 8 characters (for
example, 3 character title):
After entering 3 characters, the 4th character space will
be blinking. Go to step 6 to complete the title.
—
—
Titling Discs/Stations
5
Turn the Rotary encoder to select the desired
letter/numeral/symbol available for naming.
Press Rotary encoder to store the first character.
2
3
4
5
Press and hold -/J for at least 2 seconds.
The title in the display will blink.
Press g or f repeatedly until the title you
want to erase is displayed.
Press and hold -/J for at least 2 seconds to erase
the title displayed.
Press TITLE to cancel the title erasing mode.
• You cannot erase CD-TEXT.
• “NO DATA” is displayed for 2 seconds if the title is not input in
step 2, or if the title is erased in step 4.
Blackout Mode On and Off
When Blackout mode is turned on, the display will turn off to reduce
power consumption.
This additional power enhances the sound quality.
Press and hold DISP/B.OUT (CDA-9815RB/CDA9813R/CDA-9812RX) or MUTE/B.OUT (CDA-9811R) for
at least 3 seconds to activate the blackout mode.
The display will turn off.
• If any button on the unit is pressed during the blackout mode, the
function will be displayed for 5 seconds to show the operation
before returning to Blackout mode.
To cancel Blackout mode, press and hold DISP/B.OUT (CDA9815RB/CDA-9813R/CDA-9812RX) or MUTE/B.OUT (CDA9811R) for at least 3 seconds.
The first character will stop blinking and the display will
automatically advance to the next character. When that
character begins to blink, you may choose the next letter
or symbol of your title.
Autogood products internet store http://130.com.ua
25-EN
i-Personalize™
Operation (CDA-9815RB/CDA9813R only)
SOURCE/
POWER
Data Downloading
1
2
3
-/J
Rotary encoder
Insert the CD-R disc containing the data.
If the source is not the CD mode, press SOURCE/
POWER to change to CD mode.
Press and hold -/J for at least 2 seconds.
The mode switches to the download mode to show the
download confirmation screen.
Turn the Rotary encoder to select “OK”, then
press the Rotary encoder.
Data search of the disc starts and the first file name is
displayed.
• Selecting “NG” will halt the download mode.
• If a file is not found by the data search, “NO FILE” is indicated.
• The “NO FILE” display will automatically disappear if no
operation is performed for 5 seconds.
4
Data downloading starts.
The file currently shown in the display is downloaded.
If you want to download other files, select NEXT FILE to
call up file names.
About i-Personalize™
You can download data (from Alpine’s website) to a CD-R, and
download and store the data to the CDA-9815RB/CDA-9813R.
To start i-Personalize, access the URL below and follow the on-screen
instructions.
a
.u
CANCEL
: Halts the download
DOWNLOAD : Starts the download
NEXT FILE : Searches the next file
m
o
.c
http://www.alpine.com or http://www.alpine-europe.com
or http://www.alpine.com.au
Downloadable data
Turn the Rotary encoder to select “DOWNLOAD”,
and then press the Rotary encoder to start.
0
3
1
Parametric
equalizer
Data is memorized in Preset 6 of the
Parametric EQ Mode.
Time correction
Data is memorized in Preset 6 of the
Time Correction Mode.
Crossover
Data is memorized in Preset 6 of the
crossover mode.
The file name of download data shall be
“A_U*****.MP3.”
A_U∗∗∗∗∗.MP3
Extender (fixed)
Identifier (alphabet or number 5
letters maximum)
5
When data download is finished successfully, the
confirmation screen is displayed for 5 seconds and
the download mode closes.
Successfully downloaded items are indicated as checked
boxes on the confirmation screen.
PARAMETRIC EQ data
The data is memorized in Preset 6 of Parametric EQ mode.
The memorized data settings in Preset 6 (Parametric EQ
mode) are automatically applied.
X-OVER (Crossover) data
The data is memorized in Preset 6 of X-OVER mode. The
memorized data settings in Preset 6 (X-OVER mode) are
automatically applied.
You cannot download the data if the setting of the 2WAY/3WAY
switch is not suitable for the data.
TIME CORRECTION data
The data is memorized in Preset 6 of the Time correction
mode. The memorized data settings in Preset 6 (Time
Correction mode) are automatically applied.
• When you download the data again, the data is overwritten in
Preset 6.
Header (fixed)
You can create a file name via the website. Do not change a
file name once it has been created. Malfunction may result.
• For details about procedures of download, see ALPINE’s Web site.
• If a external audio processor is connected, data that is downloaded
cannot be used.
26-EN
Autogood products internet store http://130.com.ua
Switching the Tuner Mode
SETUP
NORMAL (Initial setting) / HI-FI / STABLE
You can flexibly customize the unit to suit your own preferences and
usage. Choose the SETUP menu from Sound Customizing, Visual
Customizing, etc., to select your desired setting.
SOURCE/
POWER
BAND/TEL.
Rotary encoder
This unit incorporates the MAX TUNE SQ for the highest quality
tuner audio. Moreover, you can choose between three settings to suit
your own personal sound preferences and usage.
NORMAL: Standard setting
HI-FI: Sound quality priority setting
STABLE: Noiseless priority setting
• If you find the sound is very noisy while listening to the tuner in HiFi mode, we recommend you change to Normal mode.
Subwoofer On and Off
SUB-W ON (Initial setting) / SUB-W OFF
When the subwoofer is on, perform the steps below to adjust the
subwoofer output phase and level.
1 Press the Rotary encoder repeatedly to select the
SUB-W mode.
g
f
F/SETUP
SUB-W → BALANCE → FADER → DEFEAT → VOLUME →
SUB-W
The common operation for SETUP is step 1 to 4 as
follows. See down below for further information
about each SETUP menu.
1
2
Press and hold F/SETUP for at least 3 seconds.
SETUP mode is activated.
Press g or f to select the desired SETUP
menu.
STEREO (Initial setting) / MONO
You can set the subwoofer output to stereo or monoaural. Make sure
to set the correct output for your subwoofer type.
STEREO: Subwoofer stereo (L/R) output
MONO: Subwoofer monaural output
Here is the explanation for CDA-9815RB display
example.
Sound (Beep) Guide Function
FM-LEVEL → REG*5 → PI SEEK*5 → NORMAL/HI-FI/STABLE
→ AMBER*4 → DIMMER*7 → SUB-W → SUB-W STEREO/
SUB-W MONO*2 → CD-DA / CD-DA/MP3*6 → BEEP →
SCROLL → SCROLL TYPE*1 → MUTE → INTERRUPT → AUX
→ (AUX name)*3 → PWR-IC → FONT*1 → CONTRAST*1 →
DEMO → FM-LEVEL
This function will give audible feedback with varying tones
depending upon the button pressed.
0
3
1
*1
*2
*3
*4
*5
*6
CDA-9815RB only.
CDA-9815RB/CDA-9813R only.
Displayed only when AUX is ON.
CDA-9813R only
“RDS” (page 9 to 12)
Displayed for CDA-9811R if an MP3 compatible changer is
connected.
*7 CDA-9815RB/CDA-9813R/CDA-9812RX only.
Press BAND/TEL. to change the setting.
(e.g. Select BEEP ON or BEEP OFF.)
• The Display Contrast described in the section “Adjusting Display
Contrast (CDA-9815RB only)” can also be changed by turning the
Rotary encoder.
4
a
.u
Setting the Subwoofer Output (CDA-9815RB/CDA-9813R only)
m
o
.c
(e.g. Select BEEP)
3
2 Press g or f.
The subwoofer output phase is toggled SUB-W
NORMAL (0°) or SUB-W REVERS (180°).
To adjust the level, turn the Rotary encoder.
Press F/SETUP again.
The display returns to normal mode.
Sound Customizing
Adjusting Source Signal Levels
FM-LEVEL HIGH (Initial setting) / FM-LEVEL LOW
If the difference in volume level between the CD player and FM radio
is too great, adjust the FM signal level.
BEEP ON (Initial setting) / BEEP OFF
Visual Customizing
Changing Lighting Colour (CDA-9813R only)
AMBER ON/AMBER OFF (Initial setting)
You can change the lighting colour on the front panel.
AMBER ON: Amber colour
AMBER OFF: Green colour
Dimmer Control (CDA-9815RB/CDA-9813R/CDA-9812RX only)
DIMMER AUTO (Initial setting) / DIMMER MANUAL
Set the DIMMER control to AUTO to decrease the illumination
brightness of the unit with the head lights of the vehicle ON.This
mode is useful if you feel the unit's backlighting is too bright at night.
Scroll Setting
SCROLL AUTO / SCROLL MANUAL (Initial setting)
This CD player can scroll the disc and track names recorded on CDTEXT discs, as well as the text information of MP3/WMA files,
folder names, and tags. (This function can be used for CDA-9811R if
a changer compatible with CD-Text is connected.)
SCROLL AUTO : The CD text information, the text information
of folder and file names, and the tags are scrolled
automatically.
SCROLL MANUAL : The display is scrolled only when a disc
is loaded or when a track is changed, etc.
• The unit scrolls CD text names, folder names, file names or tag
display. The disc titles input manually (page 25) cannot be
scrolled.
Autogood products internet store http://130.com.ua
27-EN
Scroll Type Setting (CDA-9815RB only)
Connecting to an External Amplifier
TYPE1 (Initial setting) / TYPE2
PWR-IC ON (Initial setting) / PWR-IC OFF
Two types of scroll can be selected.
When an external amplifier is connected, sound quality can be
improved by stopping the power supply of the built-in amplifier.
TYPE1: The upper line and lower line scroll alternately.
TYPE2: The upper line and lower line scroll at the same time,
but at different speeds, when the “Scroll Setting”
(page 27) is set to “SCROLL AUTO.”
PWR-IC OFF : Use this mode when the front and rear preamplifier of the unit are used to drive an external amplifier
connected to the speakers. In this setting, the head unit’s
internal amplifier has no output to drive speakers.
Switching the Character Font (CDA-9815RB only)
Front
left
TYPE-1 (Initial setting) / TYPE-2
Amplifier
Two types of font can be selected.
Front
right
You can select the font type you like.
Adjusting Display Contrast (CDA-9815RB only)
Rear
left
Amplifier
CONTRAST
Rear
right
You can adjust the display contrast for better visibility.
You can adjust in a range of - 6 and + 6.
(Connecting example for CDA-9815RB)
• The initial setting at the factory is “0.”
PWR-IC ON : The speakers are driven by the built-in amplifier.
Demonstration
Speakers
DEMO ON / DEMO OFF (Initial setting)
SPEAKER
RIGHT FRONT
This unit has a Demonstration feature which simulates the display
functions.
a
.u
• To quit Demo mode, set to DEMO OFF.
m
o
.c
MP3
Playing MP3 Data
CD-DA (Initial setting) / CD-DA/MP3
This product can playback CDs containing both CD and MP3/WMA
data. However, in some situations (some enhanced CDs), playback
may be difficult. For these special cases, you can select playback of
CD data only. When a disc contains both CD or the MP3/WMA data,
playback starts from the CD data portion of the disc. MP3 can be
played back for CDA-9811R if an MP3 compatible changer is
connected.
0
3
1
CD-DA : Only CD data can be played back.
CD-DA/MP3 : Both CD data and MP3/WMA file tracks can be
played back.
• Perform this setting before inserting a disc. If a disc has already
been inserted, perform the setting after you remove the disc. (If you
use an MP3 changer, you have to change discs.)
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
Rear
right
Rear
left
Front
left
• No sound is produced by the system when the power output is
set to OFF.
Setting Tone Defeat for External Devices
INTERRUPT ON / INTERRUPT OFF (Initial setting)
When inputting external devices to this unit, turning tone defeat on
will bypass BASS,TREBLE, EQ and MX, i.e., sound for external
devices is output at the default setting.
External Device
Turning Mute Mode On/Off
MUTE ON (Initial setting) / MUTE OFF
If a device having the interrupt feature is connected, audio will be
automatically muted whenever the interrupt signal is received from
the device.
Setting the AUX Mode (V-Link)
AUX ON / AUX OFF (Initial setting)
You can input TV/video sound by connecting an optional Ai-NET/
RCA Interface cable (KCA-121B) or Versatile Link Terminal (KCA410C) to this component.
You can change the AUX name display when AUX ON is set. Select
the AUX name by pressing g or f. Then press BAND/TEL.
If the KCA-410C is connected, it is possible to select two AUX
names.
• Via KCA-410C, up to 2 external devices with RCA output can be
connected. In this case, press SOURCE/POWER to select AUX
mode and then press BAND/TEL. to select your desired device.
28-EN
Front
right
Autogood products internet store http://130.com.ua
Dynamic Label Display: the Ensemble Label is displayed
for 2 seconds, then the Service Label is displayed for 2
seconds, and then the display is changed to the Dynamic
Label after receiving the broadcasting station.
DAB (Optional)
SOURCE/ TUNE/
POWER
A.ME
g
f
BAND/
TEL.
T.INFO F/SETUP
TITLE
3/PTY
Frequency Display* : the frequency of received stations
are displayed.
Preset buttons
(1 through 6)
• To switch the frequency display on the CDA-9813R/CDA-9812RX/
CDA-9811R, press TITLE. For details, see “Changing the Display
Mode” (page 31).
• When you use DAB, you can select a desired ensemble which may
contain one or more services, any of which can be received.
Furthermore, each service contains a Service Component, which
itself can contain any number of Primary or Secondary services,
depending on the Service Component. Several different kinds of
service can therefore be selected.
* CDA-9813R/CDA-9812RX/CDA-9811R only
4/P/S
Changing the Service
Using DAB Receiver for the Ensemble Seek
Tuning (Optional)
DAB (Digital Audio Broadcasting) offers excellent sound quality even
in a moving vehicle, enabling you to receive various types of
information, including weather and traffic information, and it also
displays information sent from the broadcasting stations. You can
also let urgent broadcasts or announcements interrupt a current
broadcast.
0
3
1
Press SOURCE/POWER to select DAB.
1
While receiving the ensemble, momentarily press
g or f, and select the service that you desire.
The selected service label is displayed for 2 seconds, and
then you return to the display that you select with the
steps described under the section “Changing the Display
Mode” (page 31).
a
.u
m
o
.c
• If you connect the DAB Receiver Box TUA-T100DAB (separately
sold), you can control DAB for the reception of broadcast.
• CD quality sound can be obtained from DAB broadcasts, although
quality may differ on some services.
• Some broadcasting stations may perform test broadcasts.
• When DAB reception is poor, metallic noise may occur. This is not
a malfunction.
1
2
3
Services are received within the ensemble that you are currently
receiving.
Changing the Service Component
You can change Audio Services of the Service Component between
the Primary and Secondary, when listening to an Audio Service that
has a Secondary Service Component.
1
Press BAND/TEL. to select DAB1, DAB2, or DAB3.
If you press and hold g or f while receiving
DAB1, 2, or 3, it starts searching for ensemble
automatically.
By selecting the mode in the “Changing the Display
Mode” (page 31), the display shows the status of the
broadcasting stations that have been received as follows:
Channel No. Display: the channel numbers of received
stations are displayed.
Ensemble Label Display: the Ensemble Label of received
station is displayed.
2
Press F/SETUP so that the “FUNC” indicator lights
up. (Only the underlined portion of the “FUNC”
indicator for CDA-9811R.)
Press 4/P/S to change the Service Component
between the Primary and Secondary broadcast.
Every time you press the button the selection toggles.
The Component label is displayed for 2 seconds, and
then you return to the display that you selected with the
steps described under the section “Changing the Display
Mode” (page 31).
• If there exists a Secondary Service Component within a service, the
indicator “S” blinks on the display. When receiving the Secondary
Service Component, the indicator “S” remains lit.
Service Label Display: the Ensemble Label is displayed
for 2 seconds and then the Service Label is displayed
after receiving the broadcasting station.
Component Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is changed
to the Component Label after receiving the broadcasting
station.
Autogood products internet store http://130.com.ua
29-EN
Memorizing the Service
Memorizing the Ensemble Automatically
1
2
1
3
Select the service that you want to memorize.
Press any one of the Preset buttons (1 through
6) for at least 2 seconds while the “FUNC”
indicator (only underlined portion of the “FUNC”
indicator for CDA-9811R) goes out. The selected
service is memorized.
2
To memorize more, repeat the above steps 1 and 2.
Press and hold TUNE/A.ME for at least 2 seconds.
The ensemble is searched for, and six ensembles are
automatically received and memorized with the preset
buttons (1 through 6).
When memorization has completed, the Ensemble that
was memorized last is received.
By selecting the mode in the “Changing the Display
Mode” (page 31), the display shows the status of the
broadcasting stations that have been received as follows:
• You can memorize up to 18 stations (6 stations for each band;
DAB1, DAB2, DAB3).
• If you select a preset button that has already memorized a service,
the new selection takes it over.
• When you are not receiving DAB, the service is not memorized.
(Memorize the service when the DAB reception is good)
Channel No. Display: the channel numbers of received
stations are displayed.
Ensemble Label Display: the Ensemble Label of received
station is displayed.
Receiving the Memorized Service
1
2
Press BAND/TEL. to select the band that you want
to receive.
Service Label Display: the Ensemble Label is displayed
for 2 seconds and then the Service Label is displayed
after receiving the broadcasting station.
Press BAND/TEL. to select your desired band.
Component Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is changed
to the Component Label after receiving the broadcasting
station.
Press one of the Preset buttons (1 through 6).
a
.u
The selected service is received.
By selecting the mode in the “Changing the Display
Mode” (page 31), the display shows the status of the
broadcasting stations that have been received as follows:
m
o
.c
Dynamic Label Display: the Ensemble Label is displayed
for 2 seconds, then the Service Label is displayed for 2
seconds, and then the display is changed to the Dynamic
Label after receiving the broadcasting station.
Channel No. Display: the channel numbers of received
stations are displayed.
Ensemble Label Display: the Ensemble Label of received
station is displayed.
0
3
1
Service Label Display: the Ensemble Label is displayed
for 2 seconds and then the Service Label is displayed
after receiving the broadcasting station.
Component Label Display: the Ensemble Label is
displayed for 2 seconds, then the Service Label is
displayed for 2 seconds, and then the display is changed
to the Component Label after receiving the broadcasting
station.
Dynamic Label Display: the Ensemble Label is displayed
for 2 seconds, then the Service Label is displayed for 2
seconds, and then the display is changed to the Dynamic
Label after receiving the broadcasting station.
Frequency Display*2 : the frequency of received stations
are displayed.
• To switch the frequency display on the CDA-9813R/CDA-9812RX/
CDA-9811R, press TITLE. For details, see “Changing the Display
Mode” (page 31).
• If no ensemble is received, the one that has been received before
you perform this automatic memorization is received.
*2 CDA-9813R/CDA-9812RX/CDA-9811R only
PTY (Programme Type) Tuning
1
Frequency Display*1 : the frequency of received stations
are displayed.
• To switch the frequency display on the CDA-9813R/CDA-9812RX/
CDA-9811R, press TITLE. For details, see “Changing the Display
Mode” (page 31).
• When you receive the Secondary Service Component, you
memorize the service, but when you call out this memorized
service, the Primary Service Component will be called out.
*1 CDA-9813R/CDA-9812RX/CDA-9811R only
2
3
4
Press F/SETUP so that the “FUNC” indicator lights
up. (Only the underlined portion of the “FUNC”
indicator for CDA-9811R.)
Press 3/PTY to go to the PTY Select mode.
Press g or f to select your desired
programme type.
After selecting a programme type, and when the
“FUNC” indicator lights up (only the underlined
portion of the “FUNC” indicator for CDA-9811R),
press 3/PTY to go to the PTY Search mode.
• To cancel the PTY Search mode during the PTY search, press the
PTY button.
5
30-EN
When the station is received, the received
programme type is displayed for 5 seconds. If no
station is found, “NO PTY” is displayed for 5
seconds.
• Above functions can be performed only for services within an
Ensemble.
Autogood products internet store http://130.com.ua
Turning ON/OFF Traffic News Announcement
Changing the Display Mode
When you set to ON, you can automatically receive the Traffic News.
You can display information that is sent from broadcasting stations,
such as the channel number or the service name that you are receiving
or listening.
1
Press T.INFO to set ON/OFF for the Traffic News.
You can also set the RDS stations at the same time.
• This operation can also be performed by turning the Traffic News
ON/OFF in the “Setting the Announcement Select Mode” on this
page.
Setting the Announcement Select Mode
1
2
3
Press T.INFO for at least 2 seconds to turn ON the
Announcement Select mode.
Press g or f to select “ANNOUN,” and then
press BAND/TEL. to set it ON.
After turning ON the “ANNOUN,” press g or f
to select your desired Announcement.
Announcement → All Select → Traffic News → Travel News →
Warning → News → Weather → Event → Special Event →
Radio Info → Sports news → Financial news →
Announcement
4
While receiving DAB, press TITLE to change the
display mode.
Channel No. Display → Ensemble Label Display → Service
Label Display → Component Label Display*1 → Dynamic
Label Display*2 → Frequency Display*3 → Channel No.
Display
*1 You can display this only when the broadcasting station supplies
the Service Component Label. Otherwise, “NO COMPO” is
displayed.
*2
• If you set “SCROLL AUTO” for “Scroll Setting,” the character
information that is sent from the broadcasting station is scrolled
when it displayed.
If you are set to “SCROLL MANUAL” while displaying the
Dynamic Label and press and hold TITLE for at least 3 seconds,
you can scroll the character information once.
• “NO TEXT” is displayed when broadcasting stations which
contain no Dynamic Label are received. However, when a station is
waiting for its reception, “WAITING” is displayed.
*3 CDA-9813R/CDA-9812RX/CDA-9811R only.
a
.u
Press BAND/TEL. to set ON/OFF for the selected
Announcement.
m
o
.c
Repeat Steps 3 and 4 to set more.
5
1
To set the Announcement Select mode OFF, press
T.INFO for at least 2 seconds.
• When one of the selections between “All Select” and “Financial
news” is set ON, no announcement interrupts are made if you set
OFF for the “Announcement”.
• If you set ON/OFF with the “All Select” selection, you can set ON/
OFF for the selections from “Traffic News” to “Financial news”.
• When an urgent broadcast is received, the mode automatically
changes to the DAB mode to receive the Alarm Announcement. If
you adjust the volume level at this time, that volume level is
memorized, and that volume level is applied the next time you
receive an urgent broadcast.
• If the announcement that you select in Step 3 interrupts, the
selected announcement Label is displayed. If you adjust the
volume level at this time, that volume level is memorized, and that
volume level is applied the next time announcement interrupts.
0
3
1
Autogood products internet store http://130.com.ua
31-EN
Displaying the Regional Label
The regional name of the ensemble that you are listening is displayed.
1
Press TITLE for at least 3 seconds.
“REGIONAL” is displayed for two seconds, and then the
Regional Label is displayed for 5 seconds, and then you
return to the display that you selected with the steps
described under the section “Changing the Display
Mode” on page 31.
• If no Regional Label is received, “NO REGON” is displayed.
• When you are in the Dynamic Label mode, you cannot display the
Regional Label.
Receiving Announcement Information of DAB
Local Stations
1
2
3
When the DAB reception is poor, you can set this selection ON to
automatically change to the RDS station (a station that can be
received) within the same broadcasting station until good reception is
achieved. You can switch this for voice only (except Service label/
Dynamic label display). The display and operation remain as for
DAB.
1
2
3
4
Press F/SETUP for at least 3 seconds.
Press g or f to select “R/D SW.”
Press BAND/TEL. to select either ON or OFF.
Press F/SETUP to return to the normal mode.
• When reception is being changed from DAB to RDS, the DAB
indicator blinks.
Press F/SETUP for at least 3 seconds.
Press g or f to select “DAB REG” (“REG”).
Press BAND/TEL. to select ON or OFF for DAB
REG.
ON: You can automatically receive announcement
interruptions that are valid for the region you are
currently in.
OFF: Announcement interruptions are valid for all regions.
4
Setting for Automatic Change from DAB to
RDS
a
.u
If you set this ON when receiving the sound of a wide Dynamic
Range, the DRC (Dynamic Range Control) gain increases when the
source sound is small, and the DRC (Dynamic Range Control) gain
decreases when the source sound is large, making the Dynamic Range
narrower to give you better and more comfortable sound even in the
vehicle that produces a large noise.
m
o
.c
Press F/SETUP to return to the normal mode.
0
3
1
32-EN
Setting ON/OFF for DRC (Dynamic Range
Control)
1
2
3
4
Press F/SETUP for at least 3 seconds.
Press g or f select “DAB DRC” (“DRC”).
Press BAND/TEL. to select either ON or OFF.
Press F/SETUP to return to the normal mode.
• When a radio programme is set to ON, sound other than what you
previously set may be produced depending on the broadcast. In this
case, turn the programme OFF.
Autogood products internet store http://130.com.ua
MobileHub™ Link
Operation(Optional)
SOURCE/
POWER
-/J
BAND/
TEL. TITLE
8 SEARCH
9
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9815RB/CDA-9813R/CDA9812RX/CDA-9811R as malfunction can result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
• The telephone volume can be adjusted on the CDA-9815RB/CDA9813R/CDA-9812RX/CDA-9811R. The volume you set during the
call is memorized, and is automatically applied again on the next
call.
• While telephoning or receiving incoming calls, press TITLE to
show the Network Operator display for 5 seconds.
Incoming Calls
g
f
F/SETUP
1
2
Preset buttons
(1 through 6)
Rotary encoder
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone while
driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
Press :/J to receive an incoming call.
Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source
mode.
• When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call.
• The incoming call can be switched to Automatic Calling or Manual
Calling.
a
.u
1 Press and hold F/SETUP for at least 3 seconds.
2 Select the Telephone mode by pressing g or f.
m
o
.c
3 Press BAND/TEL. to change to AUTO or MANUAL
(MANU).
4 Press F/SETUP to return to normal mode.
• Press BAND/TEL. during an incoming call to disconnect it.
0
3
1
• If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
• Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
1
Press and hold BAND/TEL. for at least 2 seconds
to turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
• When a portable telephone is not connected, press and hold
BAND/TEL. for at least 2 seconds. “NO PHONE” is displayed for
about 2 seconds, then the mode returns to the original source
mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of CDA-9815RB/
CDA-9813R/CDA-9812RX/CDA-9811R is off, the power of CDA9815RB/CDA-9813R/CDA-9812RX/CDA-9811R will turn on
automatically for a hands-free call.
• Even if the power of the portable telephone is off, when CDA9815RB/CDA-9813R/CDA-9812RX/CDA-9811R is set to Telephone
mode, the power of the portable telephone will be turned on.
• Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
Autogood products internet store http://130.com.ua
33-EN
Calling by the outgoing/incoming/absent incoming history
Calling
You can place a call to any of the last 999 calls by the outgoing/
incoming/absent incoming history.
Calling by the address book
You can call up the address book registered in the portable telephone
to call from.
1
2
Press and hold BAND/TEL. for at least 2 seconds.
Press SEARCH
4
5
to select Phone Book mode.
3
When displaying the Alphabetic Sort List, turn the
Rotary encoder or press g or f to select
the addressee.
Press :/J or Rotary encoder to place a call.
4
5
6
4
5
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
Retrieving an addressee by Selecting Search (A-Z search)
3
2
A list in alphabetic order is displayed.
Retrieving an addressee by Alphabetic Sort List
3
1
Press 8 or 9 to select an initial letter (A to Z) of the
addressee.
Press 8 or 9 to select outgoing history (display
example: “DIALED”), incoming history (display
example: “RECEIVED” ), absent incoming history
(display example: “MISSED”).
Turn the Rotary encoder, or press g or f to
select the addressee from the outgoing or
incoming history.
Press :/J or the Rotary encoder to place a call.
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
• If all telephone numbers and registered names cannot be displayed
at once, press TITLE to show undisplayed numbers and names.
• “NO MEMORY” (“NO MEM” for CDA-9811R) is displayed if
there is no incoming history.
a
.u
SMS (Short Message Service) Operation
m
o
.c
Turn the Rotary encoder to select the addressee.
Press the Rotary encoder to place a call.
You can be informed when you receive a short message.
Receiving a short message
Press BAND/TEL. to end the call.
0
3
1
Telephone mode will end and return to the original source
mode.
1
• If all telephone numbers and registered names cannot be displayed
at once, press TITLE to show undisplayed numbers and names.
• “NO MEMORY” (“NO MEM” for CDA-9811R) is displayed if
nothing is registered in the Phone Book.
Calling by using the Speed Dial
You can place a call by retrieving one of the telephone numbers
registered in No. 1 to 9 of the address book.
1
2
Press SEARCH
in Phone Book mode to select
the History mode.
When a text message is received, “NEW
MESSAGE” for CDA-9815RB, “NEW MESSAG” for
CDA-9813R/CDA-9812RX or “NEW MSG” for CDA9811R is indicated on the display.
The contents of the received message can only be read
from the portable phone's display.
2
Press any one of the buttons on the unit to cancel
the display. The buttons that are pressed will enter
the mode or will be activated.
Press and hold BAND/TEL. for at least 2 seconds.
Within 5 seconds, press and hold (for at least 2
seconds) a preset button (1 through 6) to place
a call.
By pressing F/SETUP, and then pressing a preset
button (1 through 3) for at least 2 seconds, you
can place a call to the number registered in 7 to 9.
• You can place a call by pressing :/J after momentarily pressing
the preset button (1 through 6) of the number you wish to call.
• You can place a call by pressing the Rotary encoder, after selecting
a number which you wish to call, by pressing g or f , or by
turning the Rotary encoder.
3
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
• If there is no telephone number registered to a preset button, “NO
PRESET” (“NO P-SET” for the CDA-9811R) is displayed when
you try to place a call.
34-EN
Autogood products internet store http://130.com.ua
Changer (Optional)
SOURCE/
-/J
POWER
Playing MP3 Files with the CD Changer
(Optional)
If you connect a changer compatible with MP3, you can play CDROMs, CD-Rs, and CD-RWs containing MP3 files on this unit.
BAND/TEL.
1
2
3
Select buttons (1 through 6)
Press SOURCE/POWER to switch to the MP3
Changer mode.
Press any one of the disc select buttons (1
through 6) corresponding to one of the discs
loaded in the CD Changer.
To pause playback, press -/J.
Pressing -/J again will resume playback.
• The unit can play discs containing both audio data and MP3 data.
• For operating MP3 with an MP3 compatible CD Changer, refer to
“CD/MP3/WMA” pages 13 to 16.
Controlling CD Changer (Optional)
An optional 6-disc or 12-disc CD Changer may be connected to this
unit if it is Ai-NET compatible. With a CD Changer connected to the
Ai-NET input of this unit, the CD Changer will be controllable from
this unit.
Using the KCA-400C (Multi-Changer Switching device) or the KCA410C (Versatile Link Terminal) multiple changers can be controlled
by this unit.
See “Multi-Changer Selection” on this page for selecting the CD
Changers.
Multi-Changer Selection (Optional)
• The controls on this unit for CD Changer operation are operative
only when a CD Changer is connected.
• The DVD changer (optional) is controllable from this unit as well
as the CD changer.
1
1
Alpine's Ai-NET system will support up to 6 CD Changers. When
operating two or more changers, the KCA-400C (Multi-Changer
Switching device) must be used. If you use 1 Switching device, you
can connect up to 4 CD Changers. If you use 2 Switching devices,
you can connect up to 6 CD Changers. When using KCA-410C
(Versatile Link Terminal), you can connect two changers and two
external outputs (AUX).
a
.u
m
o
.c
0
3
1
Press SOURCE/POWER on this unit to activate
the CD Changer mode.
Alternatively, press SOURCE on the remote control (CDA9815RB/CDA-9813R/CDA-9812RX only) to activate the
CD Changer mode.
Press SOURCE/POWER to activate the CHANGER
mode.
The display shows the disc number and track number.
• The source indicator varies depending on the connected source.
• Press BAND/TEL. to switch the Disc mode in the CD/Changer
mode.
2
SOURCE
BAND
Press the disc select buttons (1 through 6)
corresponding to one of the discs loaded in the CD
Changer.
The selected disc number appears in the display and CD
playback starts.
• After selecting the desired disc, you can operate in the same way as
for the CD player of this unit.
For details, please see the CD/MP3/WMA section.
• If the “FUNC” indicator (the underlined portion of the “FUNC”
indicator for CDA-9811R) is illuminated, the disc select buttons
become nonfunctional.
When a 12-disc CD Changer is connected:
To select discs numbered from 1 to 6, the procedure is the
same as for the 6-disc CD Changer. To select discs
numbered from 7 to 12, first press F/SETUP. This changes
the “D” indicator to “d.” Then press the desired preset
button. With F/SETUP activated, the preset buttons 1 to 6
will represent discs 7 to 12 respectively.
2
Press BAND/TEL. on this unit or the RUE-4187 to
activate the CD Changer Selection mode.
The CD Changer Selection mode remains active for 8
seconds.
3
Press BAND/TEL. until the desired CD Changer
indicator appears on the display.
Alternatively press BAND/TEL. on the Remote Control
(CDA-9815RB/CDA-9813R/CDA-9812RX only) until the
desired changer indicator appears on the display.
• If the selected CD Changer is not connected, the display will show
“NO CHGR” (“NO CHANGER” for CDA-9815RB).
• To operate the selected changer, see “CD/MP3/WMA” (page 13).
• For further details about the external input (AUX) when using
KCA-410C, see “Setting the AUX Mode (V-Link)” on page 28.
Autogood products internet store http://130.com.ua
35-EN
9 f UP Button
Remote Control
Radio mode: SEEK (UP) button
CD mode: Press this button to advance to the beginning
of the next track.
! 9 Button
1
2
Radio mode: Pressing this button will select, in
descending order, stations programmed into the radio's
presets as shown below.
5
6
7
8
9
!
3
6 → 5 ... 1 → 6
CD Changer mode: DISC Select (DN) button
Press this button to select a disc in descending order.
MP3/WMA mode: Press the Folder Select (DN) button to
select the folder.
"
#
4
" Mute Button
Press this button to lower the volume by 20 dB instantly.
Press this button again to cancel.
# Audio Processor Button*1
CDA-9815RB/CDA-9813R only
Each press the button to switch the audio processor
mode.
For details, refer to “Operating the Audio Processor” as
shown below.
CDA-9815RB/CDA-9813R/CDA-9812RX
Press the button to call the external audio processor
mode when the external audio processor is connected.*2
Controls on Remote Control (CDA-9815RB/
CDA-9813R/CDA-9812RX only)
1 Power Button
a
.u
Press this button to turn the power on/off.
2 Source Button
Press this button to select the audio source.
3 -/J Button
m
o
.c
Press this button to switch between the Play and Pause
modes for CD.
4 TILT 98 Buttons
Press this button to adjust the angle of the movable
display.
30
5 Band/Programme Button
1
Radio mode: BAND Button
Press this button and the band will change.
*1 This button is used for CDA-9812RX in conjunction with an
optional Ai-NET processor.
*2 For the operation of external audio processor, refer to the Owner's
Manual of the external audio processor you purchased.
Operating the Audio Processor
(CDA-9815RB/CDA-9813R only)
1
Normal mode → EQ mode (Equalizer Presets) → Private mode
(Recalling the Stored Equalizer Curve) → Time Correction
mode (Recalling the Stored Time Correction) → Crossover
mode (Recalling the Stored Crossover) → Normal mode
CD/Changer mode: To switch the disc mode.
6 Volume Adjustment Buttons
To increase the volume level:
Press the Lbutton
Press A.PROC to select the mode.
2
Press 8 or 9 to select the mode.
EQ mode
Select from FLAT, POPS, ROCK and NEWS.
Private mode/Time Correction mode/Crossover mode
Select from MEMORY 1 through 6.
To decrease the volume level:
Press the Kbutton
7 8 Button
Radio mode: Pressing this button will select, in ascending
order, stations programmed into the radio's presets as
shown below.
1 → 2 ... 6 → 1
CD Changer mode: DISC Select (UP) button
Press this button to select a disc in ascending order.
MP3/WMA mode: Press the Folder Select (UP) button to
select the folder.
8 g DN Button
Radio mode: SEEK (DN) Button
CD mode: Press this button to go back to the beginning of
the current track.
36-EN
Autogood products internet store http://130.com.ua
Battery Replacement (CDA-9815RB/CDA9813R/CDA-9812RX only)
Applicable battery: Use two “AAA” sized dry batteries or equivalent.
1
Opening the battery cover
Slide out the battery cover while firmly pressing in the
direction of the arrow.
Information
In Case of Difficulty
If you encounter a problem, please turn the power off, then on again.
If the unit is still not functioning normally, please review the items in
the following checklist. This guide will help you isolate the problem
if the unit is at fault. Otherwise, make sure the rest of your system is
properly connected or consult your authorized Alpine dealer.
Basic
2
Replacing the battery
3
Closing the cover
Insert the batteries, observing the polarities as illustrated.
No function or display.
• Vehicle's ignition is off.
- If connected following instructions, the unit will not
operate with the vehicle's ignition off.
• Improper power lead connections.
- Check power lead connections.
• Blown fuse.
- Check the fuse on the battery lead of the unit; replace with
the proper value if necessary.
• Internal micro-computer malfunctioned due to interference
noise etc.
- Press the RESET switch with a ballpoint pen or other
pointed article.
Radio
a
.u
m
o
.c
Slide the cover as illustrated until a click is heard.
0
3
1
Controllable With Remote Control
The CDA-9811R can be controlled with an optional Alpine
remote control. For details, consult your Alpine dealer.
Point the optional remote control transmitter at the remote
control sensor.
Remote control sensor
Unable to receive stations.
• No antenna or open connection in cable.
- Make sure the antenna is properly connected;
replace the antenna or cable if necessary.
Unable to tune stations in the seek mode.
• You are in a weak signal area.
- Make sure the tuner is in the DX mode.
• If the area you are in is a primary signal area, the antenna may
not be grounded and connected properly.
- Check your antenna connections; make sure the antenna is
properly grounded at its mounting location.
• The antenna may not be the proper length.
- Make sure the antenna is fully extended; if broken, replace
the antenna with a new one.
Broadcast is noisy.
• The antenna is not the proper length.
- Extend the antenna fully; replace it if it is broken.
• The antenna is poorly grounded.
- Make sure the antenna is grounded properly at its mounting
location.
CD
Connectable to Remote Control Interface Box
You can operate this unit from the vehicle's control unit when
an Alpine Remote Control Interface Box (optional) is
connected. For details, contact your Alpine dealer.
CD Player/Changer not functioning.
• Out of operating temperature range +50˚C (+120˚F) for CD.
- Allow the vehicle's interior (or trunk) temperature to cool.
CD playback sound is wavering.
• Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about
1 hour).
Autogood products internet store http://130.com.ua
37-EN
CD insertion not possible.
• A CD is already in the CD player.
- Eject the CD and remove it.
• The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
- Securely re-mount the unit.
• The disc is very dirty.
- Clean the disc.
• The disc has scratches.
- Change the disc.
• The pick-up lens is dirty.
- Do not use a commercial available lens cleaner disc. Consult
your nearest ALPINE dealer.
Error displays (built-in CD player only)
• Mechanical error
- Press c. After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest ALPINE dealer.
1
MP3 or WMA is not played back.
• Writing error occurred. The CD format is not compatible.
- Make sure the CD has been written in a supported format.
Refer to “About MP3/WMA” (page 15-16), then rewrite in
the format supported by this device.
Indication for CD Player
HIGH TEMP
HI TEMP
(CDA-9815RB)
(CDA-9813R/CDA-9812RX/CDA-9811R)
• Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
NO DISC
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted, “NO DISC” is displayed and the
unit does not start to play or eject the disc.
- Remove the disc by following these steps:
1) Press the c button.
The movable display will open.
2) Press the c button again for at least 3 seconds while the
movable display is open.
38-EN
• When “ERROR” is displayed:
If that the disc cannot be ejected by pressing c, press the RESET
switch (refer to page 6) and press c again.
If the disc still cannot be ejected, consult your Alpine dealer.
PROTECT
(CDA-9815RB/CDA-9813R/CDA-9812RX only)
• A copy-protected WMA file was played back.
- You can only play back non-copy-protected files.
(CDA-9815RB/CDA-9813R/CDA-9812RX only)
• The disc is not written in a MP3/WMA supported format.
- Use a disc written at the MP3/WMA supported format.
a
.u
Indication for CD Changer
m
o
.c
30
MP3/WMA
• Mechanism error.
1) Press the c button and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
c button again.
If the error indication still does not turn off after pressing
the c button for a few times, consult your Alpine dealer.
UNSUPPORT
CD playback sound skips without vibration.
• The disc is dirty or scratched.
- Clean the disc; damaged disc should be replaced.
CD-R/CD-RW playback not possible
• Close session (finalization) has not been performed.
- Perform finalization and attempt playback again.
ERROR
HIGH TEMP
HI TEMP
(CDA-9815RB)
(CDA-9813R/CDA-9812RX/CDA-9811R)
• Protective circuit is activated due to high temperature.
- The indicator will disappear when the temperature returns to
within operation range.
ERROR - 01
• Malfunction in the CD Changer.
- Consult your Alpine dealer. Press the magazine eject
button and pull out the magazine.
Check the indication. Insert the magazine again.
If the magazine cannot be pulled out, consult your Alpine
dealer.
• Magazine ejection not possible.
- Press the magazine eject button. If the magazine does not
eject, consult your Alpine dealer.
ERROR - 02
• A disc is left inside the CD Changer.
- Press the eject button to activate the eject function. When the
CD Changer finishes the eject function, insert an empty CD
magazine into the CD Changer to receive the disc left inside
the CD Changer.
Autogood products internet store http://130.com.ua
NO MAGAZINE
(CDA-9815RB)
NO MAGZINE
(CDA-9813R/CDA-9812RX)
CHASSIS SIZE
Width
Height
Depth
178 mm (7")
50 mm (2")
CDA-9815RB/CDA-9813R
155 mm (6-1/8")
CDA-9812RX/CDA-9811R
160 mm (6-1/4")
NO MAGZN
(CDA-9811R)
NOSEPIECE SIZE
Width
Height
Depth
• No magazine is loaded into the CD Changer.
- Insert a magazine.
NO DISC
170 mm (6-11/16")
46 mm (1-13/16")
20 mm (25/32")
• Due to continuous product improvement, specifications and design
are subject to change without notice.
• No indicated disc.
- Choose another disc.
Specifications
FM TUNER SECTION
Tuning Range
Mono Usable Sensitivity
Alternate Channel Selectivity
Signal-to-Noise Ratio
Stereo Separation
Capture Ratio
87.5 – 108.0 MHz
0.7 µV
90 dB
65 dB
35 dB
2.0 dB
MW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
531 – 1,602 kHz
25.1 µV/28 dB
LW TUNER SECTION
Tuning Range
Sensitivity (IEC Standard)
153 – 281 kHz
31.6 µV/30 dB
CD SECTION
Frequency Response
Wow & Flutter (% WRMS)
Total Harmonic Distortion
Dynamic Range
Signal-to-Noise Ratio
Channel Separation
PICKUP
Wave length
Laser power
CAUTION
CLASS 1
LASER PRODUCT
a
.u
m
o
.c
(Bottom side of player)
0
3
1
5 – 20,000 Hz (±1 dB)
Below measurable limits
0.008% (at 1 kHz)
95 dB (at 1 kHz)
105 dB
85 dB (at 1 kHz)
795 nm
CLASS I
REMOTE CONTROL
(CDA-9815RB/CDA-9813R/CDA-9812RX only)
Battery Type
“AAA” sized dry battery
Battery Quantity
2
Dimensions (W × H × D)
42 mm (1-21/32")
× 121 mm (4-25/32")
× 23 mm (29/32")
Weight (without battery)
50 g (1.8 oz)
GENERAL
Power Requirement
14.4 V DC
(11–16 V allowable)
Maximum Power Output
60 W × 4
Maximum Pre-Output Voltage 4 V/10k ohms
Bass (CDA-9812RX/CDA-9811R only)
±14 dB at 60 Hz
Treble (CDA-9812RX/CDA-9811R only)
±14 dB at 10 kHz
Weight
CDA-9815RB/CDA-9813R
1.7 kg (3 lbs. 12 oz)
CDA-9812RX/CDA-9811R
1.5 kg (3 lbs. 5 oz)
Autogood products internet store http://130.com.ua
39-EN
Installation and Connections
Before installing or connecting the unit, please read the
following and pages 3 to 5 of this manual thoroughly
for proper use.
Warning
Caution
HAVE THE WIRING AND INSTALLATION DONE BY
EXPERTS.
The wiring and installation of this unit requires special technical
skill and experience. To ensure safety, always contact the dealer
where you purchased this product to have the work done.
MAKE THE CORRECT CONNECTIONS.
Failure to make the proper connections may result in fire or
product damage.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM
SECURELY.
USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND.
Be sure to use only the specified accessory parts. Use of other
than designated parts may damage this unit internally or may not
securely install the unit in place. This may cause parts to become
loose resulting in hazards or product failure.
(Check with your dealer if you are not sure.) Failure to do so may
result in fire, etc.
BEFORE WIRING, DISCONNECT THE CABLE FROM THE
NEGATIVE BATTERY TERMINAL.
Failure to do so may result in electric shock or injury due to
electrical shorts.
DO NOT SPLICE INTO ELECTRICAL CABLES.
Never cut away cable insulation to supply power to other
equipment. Doing so will exceed the current carrying capacity of
the wire and result in fire or electric shock.
Route the cables and wiring away from moving parts (like the
seat rails) or sharp or pointed edges. This will prevent crimping
and damage to the wiring. If wiring passes through a hole in
metal, use a rubber grommet to prevent the wire’s insulation from
being cut by the metal edge of the hole.
a
.u
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE
OR DUST.
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING
HOLES.
m
o
.c
When drilling holes in the chassis for installation, take
precautions so as not to contact, damage or obstruct pipes, fuel
lines, tanks or electrical wiring. Failure to take such precautions
may result in fire.
DO NOT USE BOLTS OR NUTS IN THE BRAKE OR
STEERING SYSTEMS TO MAKE GROUND CONNECTIONS.
0
3
1
Bolts or nuts used for the brake or steering systems (or any other
safety-related system), or tanks should NEVER be used for
installations or ground connections. Using such parts could
disable control of the vehicle and cause fire etc.
KEEP SMALL OBJECTS SUCH AS BATTERIES OUT OF THE
REACH OF CHILDREN.
Swallowing them may result in serious injury.
If swallowed, consult a physician immediately.
DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER
VEHICLE OPERATION, SUCH AS THE STEERING WHEEL
OR GEARSHIFT.
Doing so may obstruct forward vision or hamper movement etc.
and results in serious accident.
IMPORTANT
Please record the serial number of your unit in the space provided
below and keep it as a permanent record. The serial number plate is
located on the bottom of the unit.
40-EN
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR
PINCHED BY A SHARP METAL EDGE.
Avoid installing the unit in locations with high incidence of
moisture or dust. Moisture or dust that penetrates into this unit
may result in product failure.
Precautions
• Be sure to disconnect the cable from the (–) battery post before
installing your CDA-9815RB/CDA-9813R/CDA-9812RX/
CDA-9811R. This will reduce any chance of damage to the
unit in case of a short-circuit.
• Be sure to connect the colour coded leads according to the
diagram. Incorrect connections may cause the unit to
malfunction or damage to the vehicle's electrical system.
• When making connections to the vehicle's electrical system, be
aware of the factory installed components (e.g. on-board
computer). Do not tap into these leads to provide power for
this unit. When connecting the CDA-9815RB/CDA-9813R/
CDA-9812RX/CDA-9811R to the fuse box, make sure the fuse
for the intended circuit of the CDA-9815RB/CDA-9813R/
CDA-9812RX/CDA-9811R has the appropriate amperage.
Failure to do so may result in damage to the unit and/or the
vehicle. When in doubt, consult your ALPINE dealer.
• The CDA-9815RB/CDA-9813R/CDA-9812RX/CDA-9811R
uses female RCA-type jacks for connection to other units (e.g.
amplifier) having RCA connectors. You may need an adaptor
to connect other units. If so, please contact your authorized
ALPINE dealer for assistance.
• Be sure to connect the speaker (–) leads to the speaker (–)
terminal. Never connect left and right channel speaker cables
to each other or to the vehicle body.
SERIAL NUMBER:
INSTALLATION DATE:
INSTALLATION TECHNICIAN:
PLACE OF PURCHASE:
Autogood products internet store http://130.com.ua
• For the screw *, provide a proper screw to the chassis installing
location.
Installation
3
Metal plate
Detachable
Front panel
Caution
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
Slide the CDA-9815RB/CDA-9813R/CDA-9812RX/
CDA-9811R into the dashboard. When the unit is in
place, make sure the locking pins are fully seated
in the down position. This can be done by pressing
firmly in on the unit while pushing the locking pin
down with a small screwdriver. This ensures that
the unit is properly locked and will not accidentally
come out from the dashboard. Install the
Detachable Front Panel.
Lock pin
Caution
Do not block the unit’s fan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause a fire.
Air ventilation hole
Air ventilation hole
Removal
1 Remove the detachable front panel.
(Rear of CDA-9812RX/CDA9811R)
(Rear of CDA-9815RB/CDA9813R)
1
m
o
.c
Hex Bolt
(Included)
<JAPANESE CAR>
30
Dashboard
1
Mounting sleeve
(Included)
a
.u
3 Pull the unit out, keeping it unlocked as you do so.
Rubber Cap
(Included)
Bracket
2 Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing).
As each pin is unlocked, gently pull out on the unit to
make sure it does not re-lock before unlocking the
second pin.
this unit
Front frame
Slide mounting sleeve from main unit (see
“Removal” on this page). Slide the mounting sleeve
into the dashboard.
2
Screws (M5 × 8)
(Included)
Metal Mounting Strap
this unit
Screw
∗
Bolt Stud
Hex Nut (M5)
Mounting Bracket
this unit
When your vehicle has the Bracket, mount the long
hex bolt onto the rear panel of the CDA-9815RB/
CDA-9813R/CDA-9812RX/CDA-9811R and put the
Rubber Cap on the hex bolt. If your vehicle does
not have the Mounting Support, reinforce the head
unit with the metal mounting strap (not supplied).
Connect all the leads of the CDA-9815RB/CDA9813R/CDA-9812RX/CDA-9811R according to
details described in the CONNECTION section.
Autogood products internet store http://130.com.ua
41-EN
Connections for CDA-9812RX/CDA-9811R
Antenna
1
ISO Antenna Plug
(Pink/Black)
AUDIO INTERRUPT IN
2
(Blue/White)
REMOTE TURN-ON
3
To vehicle phone
To amplifier or equalizer
(Orange) DIMMER
To the instrument cluster illumination lead
(CDA-9812RX only)
4
To power antenna
(Red)
5
IGNITION
(Blue)
POWER ANT
(Black)
GND
9
Ignition Key
6
!
7
Battery
8
(Yellow) BATTERY
a
.u
Speakers
%
(Green)
&
(Green/Black)
(
)
(White)
m
o
.c
(White/Black)
~
(Grey/Black)
+
(Grey)
"
,
(Violet/Black)
-
(Violet)
.
0
3
1
/
Rear Left
Front Left
Front Right
Rear Right
;
<
$
#
Ai-NET
NORM EQ/DIV
∗1
:
CD Changer
(Sold Separately)
Speakers
Front Left
>
Amplifier
Front Right
Rear Left
>
Amplifier
Rear Right
=
42-EN
>
Amplifier
Subwoofers
* 1 The label is attached on the bottom of the unit.
Autogood products internet store http://130.com.ua
1 Antenna Receptacle
2 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
# System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
• Be sure to turn the power off to the unit before changing the switch
position.
$ Power Supply Connector
4 Dimmer Lead (Orange) (CDA-9812RX only)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
% ISO Connector (Speaker Output)
& Left Rear (+) Speaker Output Lead (Green)
( Left Rear (–) Speaker Output Lead (Green/Black)
) Left Front (+) Speaker Output Lead (White)
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
~ Left Front (–) Speaker Output Lead (White/Black)
6 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
. Right Rear (+) Speaker Output Lead (Violet)
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
: Ai-NET Cable (Included with CD Changer)
7 Choke Coil with Fuse Holder (20A)
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
+ Right Front (–) Speaker Output Lead (Grey/Black)
, Right Front (+) Speaker Output Lead (Grey)
- Right Rear (–) Speaker Output Lead (Violet/Black)
/ Remote Control Interface Connector
To remote control interface box.
; Front Output RCA Connectors
RED is right and WHITE is left.
a
.u
< Rear Output RCA Connectors
RED is right and WHITE is left.
= Subwoofer Output RCA Connectors
RED is right and WHITE is left.
m
o
.c
9 ISO Power Supply Connector
> RCA Extension Cable (Sold Separately)
! Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
0
3
1
" Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with AiNET.
To prevent noise/interference in the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
Autogood products internet store http://130.com.ua
43-EN
Connections for CDA-9815RB/CDA-9813R
Antenna
ISO Antenna Convertor Plug
ISO Antenna Plug
1
(Pink/Black)
2
AUDIO INTERRUPT IN
To vehicle phone
(Blue/White)
3
REMOTE TURN-ON
To amplifier or equalizer
(Orange) DIMMER
To the instrument cluster illumination lead
4
(Red)
IGNITION
5
(Blue)
POWER ANT
6
(Black)
GND
To power antenna
9
Ignition Key
7
!
(Yellow) BATTERY
Battery
8
a
.u
Speakers
&
(Green)
(
(Green/Black)
)
~
(White)
m
o
.c
(White/Black)
(Grey/Black)
(Grey)
+
,
-
(Violet)
$ F/R Sub. W
Front Left
Front Right
.
0
3
1
(Violet/Black)
Rear Left
/
Rear Right
%
X-OVER
"
∗1
#
3WAY
EQ/DIV
Ai-NET
∗1
NORM
;
CD Changer
(Sold Separately)
<
?
Speakers
Front Left
Amplifier
Front Right
=
?
Rear Left
Amplifier
Rear Right
>
?
Amplifier
Subwoofers
:
44-EN
* 1 The label is attached on the bottom of the unit.
Autogood products internet store http://130.com.ua
1 Antenna Receptacle
Connect to the supplied ISO antenna convertor plug.
2 Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio Interface output of a cellular
phone which provides ground shorting when a call is
received.
3 Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
4 Dimmer Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will enable the vehicle’s
dimmer control to dim the backlighting of the unit.
5 Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+) 12V
only when the ignition is turned on or in the accessory
position.
6 Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the vehicle's power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
7 Choke Coil with Fuse Holder (20A)
8 Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle's
battery.
9 ISO Power Supply Connector
# System Switch
When connecting a processor using Ai-NET, place this
switch in the EQ/DIV position. When no device is
connected, leave the switch in the NORM position.
• Be sure to turn the power off to the unit before changing the switch
position.
$ Setting the 3WAY/2WAY switch
Set the 3way/2way Switch according to your audio system.
% Power Supply Connector
& ISO Connector (Speaker Output)
( Left Rear (+) Speaker Output Lead (Green)
) Left Rear (–) Speaker Output Lead (Green/Black)
~ Left Front (+) Speaker Output Lead (White)
+ Left Front (–) Speaker Output Lead (White/Black)
, Right Front (–) Speaker Output Lead (Grey/Black)
- Right Front (+) Speaker Output Lead (Grey)
. Right Rear (–) Speaker Output Lead (Violet/Black)
/ Right Rear (+) Speaker Output Lead (Violet)
: Remote Control Interface Connector
To remote control interface box.
; Ai-NET Cable (Included with CD Changer)
< Front Output RCA Connectors
RED is right and WHITE is left.
a
.u
= Rear Output RCA Connectors
RED is right and WHITE is left.
> Subwoofer Output RCA Connectors
RED is right and WHITE is left.
? RCA Extension Cable (Sold Separately)
m
o
.c
! Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
" Ai-NET Connector
Connect this to the output or input connector of other
product (CD changer, Equalizer, etc.) equipped with AiNET.
0
3
1
The X-Over Switch position for a two-way system
(frequency range is divided between highs for front/rear and
lows for the Subwoofer).
The X-Over Switch position for a three-way system whose
frequency range is divided among the highs (Front), mids
(Rear), and lows (Subwoofer).
The position of the X-Over switch : F/R/Sub-W
The position of the X-Over switch: 3WAY
Front high range
speaker (L)
Front high range
speaker (R)
High range
speaker (L)
High range
speaker (R)
Rear high range
speaker (L)
Rear high range
speaker (R)
Mid range
speaker (L)
Mid range
speaker (R)
Low range
speaker (R)
Low range
speaker (L)
Low range
speaker (L)
Low range
speaker (R)
Output of this unit :
Front output
Rear output
SUB-W output
• Use the SUB-W output cord to connect the unit to the low range speaker.
• You can use the built-in amplifier to output the front output/rear output.
• You cannot adjust the fader when set to 3WAY.
To prevent noise/interference in the audio system.
• Locate the unit and route the leads at least 10 cm away from the car harness.
• Keep the battery power leads as far away from other leads as possible.
• Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
Autogood products internet store http://130.com.ua
45-EN
a
.u
m
o
.c
0
3
1
Autogood products internet store http://130.com.ua
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement