CheetahSwitch Workgroup-3002A Quick Installation Guide

CheetahSwitch Workgroup-3002A Quick Installation Guide
CheetahSwitch Workgroup-3002A
Quick Installation Guide
ES3002A-TX
ES3002A-TF
E0798-R01
150888-101
Copyright © 1998 by Accton Technology Corporation. All rights reserved.
No part of this document may be copied or reproduced in any form or by any means without the prior
written consent of Accton Technology Corporation.
Quick Installation Guide
Accton makes no warranties with respect to this documentation and disclaims any implied warranties of
merchantability, quality, or fitness for any particular purpose. The information in this document is
subject to change without notice. Accton reserves the right to make revisions to this publication
without obligation to notify any person or entity of any such changes.
CheetahSwitch Workgroup-3002A
ES3002A-TX - Fast Ethernet Switch
with 2 10BASE-T/100BASE-TX Ports
ES3002A-TF - Fast Ethernet Switch
with 1 10BASE-T/100BASE-TX Port and 1 100BASE-FX Port
International Headquarters
No. 1 Creation Road III,
Science-based Industrial Park
Hsinchu 300, Taiwan, R.O.C.
Phone: 886-3-5770-270
FAX: 886-3-5770-267
BBS: 886-3-5770-654
Internet: [email protected]
USA Headquarters
P.O. Box 51420
Irvine, CA 92619-1420
Phone Numbers Sales: 888-398-2101 or 949-707-4800
Support: 888-398-4101 or 949-707-4847
RMA:
888-398-3101 or 949-707-4828
FAX: 949-707-2460
Accton is a trademark of Accton Technology Corporation. Other trademarks or brand names mentioned
herein are trademarks or registered trademarks of their respective companies.
ES3002A-TX
ES3002A-TF
E0798-R01
150888-101
CheetahSwitch Workgroup-3002A
Quick Installation Guide
Contents
Introduction
Introduction
1
Package Contents
1
Description of Hardware
1
Installing the Switch
1
Connecting the Switch System
Making a Connection via an RJ-45 Station Port
Making a Connection via an MDI Daisy-Chain Port
Making a Connection via a Fiber Optic Port
Distance Limit in Fiber Optics
2
2
2
3
3
Powering On the Switch
3
Verifying Port Status
4
Verifying System Operation
4
Applications
4
Product Specifications
Basic Criteria
Switching Criteria
5
5
6
Troubleshooting
Diagnosing Switch Indicators
Power and Cooling Problems
Installation
Transmission Mode
6
6
6
6
6
Port and Cable Assignments
RJ-45 Port Description
7
7
EMI Certification
FCC Class B Certification (USA)
Canada Department of Communications - Class B
VCCI Class B Compliance (Japan)
CE Mark Declaration of Conformance (for EMI and Safety - Europe)
7
7
8
8
8
Safety Compliance
Underwriters Laboratories Inc. (USA)
Wichtige Sicherheitshinweise (Germany)
8
8
9
Warranty
9
The CheetahSwitch Workgroup-3002A is an ideal solution for
bridging conventional 10Mbps Ethernet networks to 100Mbps
Fast Ethernet. This switch delivers dedicated 10Mbps or
100Mbps links to each attached LAN segment (independent
collision domain) – all with conventional cabling and adapters.
It can also be used to segment 10 or 100 Mbps workgroups for
increased performance. Moreover, the ES3002-TF provides a fiber optic port that can
be used to connect to a remote site up to 2 kilometers (1.24 miles) away. These
switches provide auto-negotiation to select the optimal transmission speed and duplex
mode for RJ-45 ports. They use store-and-forward switching to maintain a clean data
environment. And even provide flow control (via back-pressure) to minimize lost frames.
Package Contents
The CheetahSwitch Workgroup-3002A package includes:
• CheetahSwitch Workgroup-3002A
ES3002A-TX: Fast Ethernet Switch with 2 10BASE-T/100BASE-TX Ports, or
ES3002A-TF: Fast Ethernet Switch with 1 10BASE-T/100BASE-TX Port
and 1 100BASE-FX Port
• Four rubber foot pads
• Quick Installation Guide
• AC power cord
• Owner registration card
Description of Hardware
The ES3002A-TX contains 2 10BASE-T / 100BASE-TX ports. The ES3002A-TF has
1 10BASE-T / 100BASE-TX port and 1 100BASE-FX port. The RJ-45 ports use autonegotiation to set the transmission speed (10/100 Mbps) and mode (half/full duplex). If
the attached device does not support auto-negotiation, the speed will still be correctly
set by the switch using auto-sensing. However, if the attached device must operate at
full duplex, then it must also support auto-negotiation. Note that while the transmission
speed of the fiber optic ports is fixed at 100Mbps, the mode can be set at half or full
duplex with the port’s configure button.
The following figure shows the front panel for each of the switch models:
Installing the Switch
This switch can be installed on your desktop or on any other suitable flat surface.
Before you start installing the switch, make sure you can provide the right operating
environment, including power requirements, sufficient physical space, and proximity to
1
CheetahSwitch Workgroup-3002A
other network devices that are to be connected. Verify the following installation
requirements:
• Power requirements: 100 to 240 VAC (± 10%) at 50 to 60 Hz (± 3Hz). The switch's
power supply automatically adjusts to the input voltage level.
• The switch should be located in a cool dry place, with at least 10 cm. (4 in.) of space
at the front and back for ventilation.
• Place the switch out of direct sunlight, and away from heat sources or areas with a
high amount of electromagnetic interference.
• Check if network cables and connectors needed for installation are available.
Stick the self-adhesive rubber foot pads (that come with this package) on each of the 4
concave spaces located on the bottom of the switch. Then place it on a firm flat surface.
Connecting the Switch System
Making a Connection via an RJ-45 Station Port
The RJ-45 ports on these switches support connection to 10Mbps Ethernet or 100Mbps
Fast Ethernet, and can operate at either half or full-duplex. The transmission speed for
these ports is automatically set by the switch to match the highest speed supported by
the connected device. And the transmission mode for these ports is set using autonegotiation (if also supported by the attached device). If the device attached to any of
these ports on the switch does not support auto-negotiation, operation will default to
half duplex. Therefore, if any device attached to an RJ-45 port on this switch must
operate at full duplex, then it must also support auto-negotiation.
You can connect an RJ-45 (MDI-X) station port on the switch to any device that uses a
standard network interface such as a workstation or server, or to a network interconnection device such as a bridge or router (depending on the port type implemented).
1. Prepare the devices you wish to network. Make sure you have installed 10BASE-T
or 100BASE-TX network interface cards for connecting to the switch's RJ-45 (MDI-X)
station ports.
2. Prepare straight-through shielded or unshielded twisted-pair cables with RJ-45 plugs
at both ends. Use 100W Category 3, 4 or 5 cable for standard 10Mbps Ethernet
connections, or 100W Category 5 cable for 100Mbps Fast Ethernet connections.
3. Connect one end of the cable to the RJ-45 port of the network interface card, and the
other end to any available (MDI-X) station port on the switch. The RJ-45 ports support
either 10Mbps and 100Mbps Ethernet connections. When inserting an RJ-45 plug, be
sure the tab on the plug clicks into position to ensure that it is properly seated.
I Do not plug a phone jack connector into any RJ-45 port.
This may damage the
switch. Instead, use only twisted-pair cables with RJ-45 connectors that conform
with FCC standards.
Notes: 1. Make sure each twisted-pair cable does not exceed 100 meters (328 feet).
2. We advise using Category 5 cable for all network connections to avoid any
confusion or inconvenience in the future when you upgrade attached
devices to Fast Ethernet.
Making a Connection via an MDI Daisy-Chain Port
To make a direct connection to another compatible switch or hub, follow these steps:
1. Set the RJ-45 port configure button to MDI.
2. Prepare straight-through shielded or unshielded twisted-pair cables with RJ-45 plugs
at both ends. Use 100W Category 3, 4 or 5 cable for standard 10Mbps Ethernet
connections, or 100WCategory 5 cable for 100Mbps Fast Ethernet connections.
2
Quick Installation Guide
3. Connect one end of the cable to an MDI port on the switch, and the other end to any
MDI-X station port on the other device. When inserting an RJ-45 plug, be sure the tab
on the plug clicks into position to ensure that it is properly seated.
Notes: 1. Alternatively, you can connect from an MDI-X port on the switch to an MDI
daisy-chain port on the other device.
2. Make sure each twisted-pair cable does not exceed 100 meters (328 feet).
3. To connect to another switch or hub, you may also attach to (MDI-X) station
ports at both ends if you use crossover cabling.
4. Because switches break up the path for connected devices into separate
collision domains, do not include the switch or connected cabling in your
calculations for cascade length involving other devices.
Making a Connection via a Fiber Optic Port
If you need to connect fiber cable to the switch, models are available that support either
SC and ST type connectors. Note that while the fiber optic ports are fixed at 100 Mbps,
you can configure the mode to half or full duplex with the port’s configure button.
Prepare fiber optic cable with SC or ST connectors at both ends. When connecting the
port directly to an end-node device (e.g., a workstation or file server), run cable from the
Rx (Tx) port on the module to the Tx (Rx) port on the target device. When inserting the
cable, be sure the tab on the plug clicks into position to ensure that it is properly seated.
Note: Attach only 50/125 µm or 62.5/125 µm multimode fiber to these ports.
Distance Limit in Fiber Optics
Note that as a general rule, the length of fiber optic cable for a single switched link
should not exceed 2 kilometers (1.24 miles) at full duplex, or 412 meters (0.25 miles) at
half duplex. However, timing constraints must also be considered when calculating the
maximum cable length for your specific environment.
Collision Domain Timing Constraints - Where fiber optic cable and twisted-pair
links exist in a single collision domain with other repeater devices, the fiber length has
to be limited to satisfy Fast Ethernet timing constraints. Use the following table as a
guide for maximum fiber length with the listed topologies (IEEE802.3u).
Basic Topology Model
Sing le Switche d Link - full d up le x
- half d up le x
With Class I Re p e ate r - TX/FX links o nly
- if any T4 links p re se nt
With 1 Class II Re p e ate r - TX/FX links o nly
With 2 Class II Re p e ate rs - TX/FX links o nly
Max. Fiber Length
2 Km (1.24 mile s)
412 m (1351 fe e t)
160 m (524 fe e t)
131 m (429 fe e t)
208 m (682 fe e t)
111 m (364 fe e t)
Powering On the Switch
1. Plug the power cord into the power socket at the rear of the switch, and the other
end into a power outlet.
2. Check the LED marked Power on the front panel to see if it is on. The unit will
automatically select the setting that matches the connected input voltage. Therefore,
no additional adjustments are necessary when connecting it to any input voltage
within the range marked on the rear panel.
Note: The unit supports a "hot remove" feature which permits you to connect/
disconnect cables without powering off the switch and without disrupting the
operation of the devices attached to the switch.
3
CheetahSwitch Workgroup-3002A
Quick Installation Guide
Verifying Port Status
Check each connection by viewing the status indicators
shown in the figure to the right and the following table.
LED
Po we r
Link
Activity
Full
100
Co l
State
On
On
On
On
On
On
Indication
Switch is re ce iving p o we r.
Po rt has e stab lishe d a valid ne two rk co nne ctio n.
Traffic is trave rsing the p o rt.
Co mmunicatio ns have b e e n se t to full-d up le x mo d e .
Co mmunicatio ns have b e e n se t to a sp e e d o f 100 Mb p s.
Two o r mo re d e vice s atte mp te d to transmit at the same
time . (No rmal situtatio n und e r half d up le x CSMA/CD.)
Verifying System Operation
Verify that all attached devices have a valid connection. The switch monitors the link
status for each port. If any device is properly connected to the switch and transmitting
a link beat signal, the Link indicator will light up for the corresponding port. If the Link
indicator fails to light when you connect a device to the switch, check the following items:
•
•
•
•
Both sides of each connection must use the same transmission mode (i.e., half or full
duplex). If any device connected to an RJ-45 port must operate at full duplex then it
must also support auto-negotiation.
Be sure all network cables and connectors are properly attached to the connected
device and the switch.
See if your cable is functioning properly by using it for another port and attached
device that displays valid indications when connected to the network.
Be sure no twisted-pair cable exceeds 100 meters (328 feet), and that no fiber cable
exceeds 2 kilometers (1.24 miles) at full duplex or 412 meters (0.25 miles) at half duplex.
Applications
This switch segments your network, significantly increasing both bandwidth and
throughput. Any port on the switch can be attached to a hub (i.e., shared collision
domain) or provide a dedicated link to a single network device (e.g., a file server).
When a port on the switch is connected to a hub (i.e., a 10 or 100 Mbps repeater), the
bandwidth provided by that port is shared by all the devices connected to the attached
hub. However, when a port is connected to an end node or to a device that breaks up
the collision domain (e.g., another switch, bridge or router), the attached device has
access to the full bandwidth provided by that port.
Bridging Functions - This switch provides fully transparent bridging functions. It
automatically learns node addresses, which are subsequently used to filter and
forward all traffic based on the destination address. When traffic passes between
devices attached to the same shared collision domain, those packets are filtered from
the switch. But when traffic must be passed between unique segments (i.e., different
ports on the switch), the high-speed switching fabric forwards the packets at near
zero latency.
Switching Functions - Store-and-forward switching is used to forward traffic to
other ports. This scheme ensures data integrity and provides a clean data stream.
Flexible Configuration - This switch is designed to segment your network, thereby
improving network performance. It can be connected with standard repeater hubs,
switches, or other network interconnection devices in various configurations.
4
Product Specifications
Basic Criteria
10BASE-T / 100BASE-TX Ports (ES3002A-TX, ES3002A-TF)
Access Method
CSMA/CD, 10 or 100 Mbps
Standards Conformance
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
Communication Rate
10 or 100 Mbps (auto-detection)
Communication Mode
Half or full duplex (auto-negotiation)
Media Supported
100W Cat 3,4,5 for 10 Mbps, or
100W Cat 5 for 100 Mbps
Number of RJ-45 Ports
ES3002A-TX: 2 RJ-45 10BASE-T / 100BASE-TX ports
ES3002A-TF: 1 RJ-45 10BASE-T / 100BASE-TX port
100BASE-FX Ports (ES3002A-TF)
Access Method
CSMA/CD, 100 Mbps
Standards Conformance
IEEE 802.3u 100BASE-FX
Communication Rate
100 Mbps
Communication Mode
Half or full duplex (manual configuration)
Media Supported
50/125 mm or 62.5/125 mm multimode fiber
Number of Fiber Ports
ES3002A-TF-SC: 1 100BASE-FX SC-type port
ES3002A-TF-ST: 1 100BASE-FX ST-type port
Other Physical Characteristics
Indicators
Power, link, activity, duplex mode, speed, collision
Dimensions
251 x 118 x 37 mm (9.88 x 4.65 x 1.46 in)
Weight
0.8 kg (1.8 lb)
Input Power
Full range power input: 100 to 240V (±10%)
50 to 60 Hz (±3Hz)
Power Consumption
10 Watts max. @ 100-240 VAC
Heat Dissapation
34.1 BTU/hr @ 100-240 VAC
Temperature
0 to 40°C (32 to 104°F) Standard Operating
Humidity
5% to 95% (Noncondensing)
Certification
CE Mark
Emissions
FCC Class B, VCCI Class B, CISPR Class B
Immunity
IEC 1000-4-2/3/4/6
Safety
CSA/NRTL, TÜV/GS
5
CheetahSwitch Workgroup-3002A
Switching Criteria
Network Bridging Function
Switching Method
Address Table
Queue Buffer
Filtering/Forwarding Rate
Flow Control
Quick Installation Guide
Port and Cable Assignments
Filtering, forwarding and learning
Store-and-forward
8K entries
Same speed - 98K bytes per port,
Different speeds - 10M port: 17K bytes, 100M port: 175K bytes
Full line speed
Half duplex: back pressure; Full duplex: IEEE 802.3x
Troubleshooting
RJ-45 Port Description
RJ-45 station ports (MDI-X) can be attached to any devices
which use a standard network interface (e.g., a workstation, server, bridge or router).
RJ-45 daisy-chain ports (MDI) can be cascaded to a station port on similar networking
devices (e.g., another switch or hub). Use unshielded twisted-pair (UTP) or shielded
twisted-pair (STP) cable for RJ-45 connections: 100W Category 3, 4 or 5 cable for 10
Mbps connections or 100W Category 5 cable for 100 Mbps connections. Also be sure
that the length of any twisted-pair connection does not exceed 100 meters (328 feet).
Diagnosing Switch Indicators
Pi n
The switch can be easily monitored through panel indicators to assist the network
manager in identifying problems. This section describes common problems you may
encounter and possible solutions.
Symptom: Link indicator does not light up (green) after making a connection.
Cause:
Network interface (e.g., a network adapter card on the attached device),
network cable, or switch port is defective.
Solution:
Verify that the switch and attached device are powered on. Be sure the
cable is plugged into both the switch and corresponding device. Verify that
the proper cable type is used and its length does not exceed specified
limits. Check the adapter on the attached device and cable connections for
possible defects. Replace the defective adapter or cable if necessary.
Symptom: Power indicator does not light up (green) after power on.
Cause:
Defective power outlet, power cord, or internal power supply.
Solution: Check the power outlet by plugging in another device that is functioning
properly. Check the power cord with another device. If these measures
fail to resolve the problem, have the unit's power supply replaced by an
qualified Accton distributor.
Power and Cooling Problems
If the power indicator does not turn on when the power cord is plugged in, you may
have a problem with the power outlet, power cord, or internal power supply as
explained in the previous section. However, if the unit powers off after running for a
while, check for loose power connections, power losses or surges at the power outlet,
and verify that the fans on back of the unit are unobstructed and running prior to
shutdown. If you still cannot isolate the problem, then the internal power supply may be
defective. In this case, contact your Accton distributor for assistance.
Installation
Verify that all system components have been properly installed. If one or more
components appear to be malfunctioning (e.g., the power cord or network cabling), test
them in an alternate environment where you are sure that all the other components are
functioning properly.
Transmission Mode
Verify that each port is set to the same transmission mode used by the attached device
(i.e., half or full duplex). RJ-45 ports use auto-negotiation to set the transmission mode.
If the attached device operates at half duplex, the dufault when auto-negotiation fails,
then it does not have to support auto-negotiation. However, if the attached device must
operate at full duplex, then it must support auto-negotiation. The transmission mode for
fiber optic ports must be set at half or full duplex using the port’s configure button.
6
1
2
3
6
4,5,7,8
Assignment
(Station Ports 1 - 2)
Inp ut Re c e iv e Data +
Inp ut Re c e iv e Data Outp ut Trans mit Data +
Outp ut Trans mit Data No t Us e d
Assignment
(Daisy-Chain Port)
Outp ut Trans mit Data +
Outp ut Trans mit Data Inp ut Re c e iv e Data +
Inp ut Re c e iv e Data No t Us e d
Schematics for both straight and crossover twisted-pair cable are shown below.
Straight-Through
(Switc h)
(Ad ap te r)
1 IRD+
1 OTD+
2 IRD2 OTD3 OTD+
3 IRD+
6 OTD6 IRD-
(Switc h)
1 IRD+
2 IRD3 OTD+
6 OTD-
Crossover
(Switc h)
1 IRD+
2 IRD3 OTD+
6 OTD-
EMI Certification
FCC Class B (USA)
Accton Technology Corporation
Model Numbers: ES3002A-TX, ES3002A-TF
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
Warning: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from the one which the
receiver is connected to
• Consult the dealer or an experienced radio/TV technician for help
7
CheetahSwitch Workgroup-3002A
Quick Installation Guide
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
Note: In order to maintain compliance with the limits of a Class B digital device, Accton
requires that you use a quality interface cable when connecting to this device. Changes
or modifications not expressly approved by Accton could void your authority to operate
this equipment. Suggested cable type is unshielded or shielded (UTP/STP) cable –
Category 3 or greater for 10Mbps connections and Category 5 for 100Mbps connections.
Class B (Canada Department of Communications)
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus", ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matériel brouilleur:
"Appareils Numérques", NMB-003 édictée par le ministère des Communications.
VCCI Class B Compliance (Japan)
CE Mark Declaration of Conformance (for EMI and Safety - Europe)
This is to certify that this product complies with ISO/IEC Guide 22 and EN45014.
It conforms to the following specifications:
EMC:
EN55022(1988)/CISPR-22(1985)
IEC1000-4-2(1995)
IEC1000-4-3(1995)
IEC1000-4-4(1995)
IEC1000-4-6(1995)
class B
4kV CD, 8kV AD
3V/m
1kV - (power line), 0.5kV - (signal line)
3Vrms
This product complies with the requirements of the Low Voltage Directive 73/23/EEC
and the EMC Directive 89/336/EEC.
Underwriters Laboratories Inc. (USA)
Important! Before making connections, make sure you have the correct Cord Set.
Check it (read the label on the cable) against the following specification list.
240 Vo lts
(No rth Ame ric a)
240 Vo lts
(Euro p e o nly)
8
1. Bitte lesen Sie diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie keine
Flüssigoder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung.
4. Die Netzanschlu ßsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen
könnte Beschädigungen hervorrufen.
7. Die Belüftungsöffnungen dienen der Luftzirkulation, die das Gerät vor Überhitzung schützt.
Sorgen Sie dafür, daß diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
9. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch
nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät
gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
13. Öffnen sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur
von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu überprüfen:
a. Netzkabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
15. Zum Netzanschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden. Für einen
Nennstrom bis 6A und einem Gerätegewicht größer 3kg ist eine Leitung nicht leichter als
H05VV-F, 3G, 0.75mm2 einzusetzen.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70dB(A)
oder weniger.
Warranty
Safety Compliance
Voltage
120 Vo lts
Wichtige Sicherheitshinweise (Germany)
C ord Set Specifications
UL Lis te d /CSA Ce rtifie d Co rd Se t
Minimum 18 AWG; typ e SVT o r SJ T thre e c o nd uc to r c o rd
Max imum le ng th o f 15 fe e t
Paralle l b lad e , g ro und ing typ e attac hme nt p lug rate d 15A, 125V
UL Lis te d /CSA Ce rtifie d Co rd Se t
Minimum 18 AWG; typ e SVT o r SJ T thre e c o nd uc to r c o rd
Max imum le ng th o f 15 fe e t
Tand e m b lad e , g ro und ing typ e attac hme nt p lug rate d 15A, 125V
Co rd Se t with H05VV-F c o rd having thre e c o nd uc to rs with
minimum d iame te r o f 0.75 mm²
IEC-320 re c e p tac le ; male p lug rate d 10A, 250V
Accton warrants to the original owner that the product delivered in this package will be
free from defects in material and workmanship for a period of three years from the date
of purchase from Accton or it’s Authorized reseller. For the warranty to apply, you must
register your purchase by returning the registration card indicating the date of purchase
and including proof of purchase. There will be a minimal charge to replace consumable
components, such as fuses, power transformers, and mechanical cooling devices. The
warranty does not cover the product if it is damaged in the process of being installed.
Accton recommends that you have the company from whom you purchased this
product install it.
THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR ANY WARRANTY ARISING
OUT OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. ACCTON SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. ACCTON NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER LIABILITY.
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement