MODEL G0833P POLAR BEAR SERIES® 10

MODEL G0833P POLAR BEAR SERIES® 10
MODEL G0833P
POLAR BEAR SERIES®
10" HYBRID TABLE SAW
w/RIVING KNIFE
OWNER'S MANUAL
(For models manufactured since 06/17)
COPYRIGHT © JUNE, 2017 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#19042BLJHMN PRINTED IN CHINA
V1.06.17
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
•
•
•
Lead from lead-based paints.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
Table of Contents
INTRODUCTION................................................ 2
Contact Info.................................................... 2
Manual Accuracy............................................ 2
Identification.................................................... 3
Controls & Components.................................. 4
Glossary of Terms.......................................... 5
G0833P Machine Data Sheet......................... 6
SECTION 1: SAFETY........................................ 9
Safety Instructions for Machinery................... 9
Additional Safety for Table Saws.................. 11
Preventing Kickback..................................... 12
Protecting Yourself From Kickback.............. 12
SECTION 5: SHOP MADE SAFETY
ACCESSORIES............................................... 49
Featherboards............................................... 49
Push Sticks................................................... 52
Push Blocks.................................................. 53
Narrow-Rip Auxiliary Fence & Push Block... 54
Outfeed & Support Tables............................ 56
Crosscut Sled............................................... 56
SECTION 6: AFTERMARKET ACCESSORIES
FROM GRIZZLY.............................................. 57
SECTION 2: POWER SUPPLY....................... 13
Converting Voltage to 115V.......................... 15
SECTION 7: MAINTENANCE.......................... 59
Schedule....................................................... 59
Cleaning & Protecting................................... 59
Lubrication.................................................... 60
SECTION 3: SETUP........................................ 16
Needed for Setup.......................................... 16
Unpacking..................................................... 16
Inventory....................................................... 17
Hardware Recognition Chart........................ 19
Cleanup......................................................... 20
Site Considerations....................................... 21
Assembly...................................................... 22
Dust Collection.............................................. 27
Test Run....................................................... 28
SECTION 8: SERVICE.................................... 61
Troubleshooting............................................ 61
Blade Tilt Stops............................................. 63
Miter Slot to Blade Parallelism...................... 65
Spreader or Riving Knife Alignment............. 67
Fence Adjustments....................................... 69
Fence Scale Calibration................................ 72
Table/Dado Insert Adjustment...................... 72
Miter Gauge Adjustments............................. 73
Belt Tension & Replacement........................ 74
SECTION 4: OPERATIONS............................ 29
Operation Overview...................................... 29
Workpiece Inspection................................... 30
Non-Through & Through Cuts...................... 30
Blade Requirements..................................... 31
Blade Selection............................................. 31
Blade Installation.......................................... 33
Blade Guard Assembly................................. 34
Riving Knife................................................... 37
Ripping.......................................................... 38
Crosscutting.................................................. 39
Miter Cuts..................................................... 39
Blade Tilt/Bevel Cuts.................................... 40
Dado Cutting................................................. 40
Rabbet Cutting.............................................. 42
Resawing...................................................... 44
SECTION 9: WIRING....................................... 75
Wiring Safety Instructions............................. 75
Wiring Diagram............................................. 76
Electrical Components.................................. 77
SECTION 10: PARTS...................................... 78
Body.............................................................. 78
Trunnion........................................................ 79
Power Switch................................................ 81
Blade Guard.................................................. 82
Miter Guage.................................................. 83
Fence............................................................ 84
Fence Rails................................................... 85
Labels & Cosmetics...................................... 86
WARRANTY AND RETURNS......................... 89
INTRODUCTION
Contact Info
Manual Accuracy
We stand behind our machines! If you have questions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number and manufacture date from the
machine ID label. This will help us help you faster.
We are proud to provide a high-quality owner’s
manual with your new machine!
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: (570) 546-9663
Email: techsupport@grizzly.com
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: manuals@grizzly.com
We made every effort to be exact with the instructions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that sometimes the machine you receive is
slightly different than shown in the manual.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something, check our
website for an updated version. We post current
manuals and manual updates for free on our website at www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write down
the Manufacture Date and Serial Number from
the machine ID label (see below). This information
is required for us to provide proper tech support,
and it helps us determine if updated documentation is available for your machine.
Manufacture Date
Serial Number
-2-
Model G0833P (Mfd. Since 06/17)
Identification
Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.
Left
Extension
Wing
Miter
Gauge
Blade
Guard
11⁄2" Dust
Port
Dust Collection
Hose
Fence
START/
STOP
Switch
Right
Extension
Wing
Blade Tilt
Lock
Blade
Height
Lock
Blade Tilt
Handwheel
Blade Height
Handwheel
Blade Tilt
Scale
Fence Lock Handle
4" Dust Port
For Your Own Safety Read Instruction
Manual Before Operating Saw
a) Wear eye protection.
b)Use saw-blade guard and spreader for
every operation for which it can be used,
including all through sawing.
c) Keep hands out of the line of saw blade.
d)Use a push-stick when required.
e)Pay particular attention to instructions
on reducing risk of kickback.
f) Do not perform any operation freehand.
g)Never reach around or over saw blade.
Model G0833P (Mfd. Since 06/17)
-3-
Controls &
Components
B. Handwheel Locks: Lock blade height
and angle when tightened (one on each
handwheel).
C. Blade Tilt Handwheel: Adjusts angle of
blade tilt from 90°–45°.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
D. Blade Height Handwheel: Adjusts blade
height from 0"–31⁄8".
B
Refer to Figures 1–3 and the following descriptions to become familiar with the basic controls of
this machine.
A.START/STOP Switch: Starts and stops the
motor. The switch can be disabled for safety
by inserting the disabling pin or a padlock
(not included) through the START button.
C
D
Figure 2. Blade adjustment handwheels and
locks.
A
E. Fence Lock Handle: Locks fence when
pushed down, unlocks fence when pulled up.
F.Fence: Guides workpiece as it moves into
blade and determines angle of cut. Fence
face can be positioned for standard cutting
operations, or placed in lower position for
blade guard clearance during narrow ripping
operations.
Figure 1. Location of START/STOP switch.
G. Fence Lock Knobs: Secure fence when
tightened; allow fence to be repositioned
along fence tube when loosened.
F
E
G
Figure 3. Location of fence controls.
-4-
Model G0833P (Mfd. Since 06/17)
Glossary of Terms
The following is a list of common definitions, terms and phrases used throughout this manual as they relate
to this table saw and woodworking in general. Become familiar with these terms for assembling, adjusting
or operating this machine. Your safety is VERY important to us at Grizzly!
Arbor: A metal shaft extending from the drive
mechanism that is the mounting location for the
saw blade.
Non-Through Cut: A cut in which the blade does
not cut through the top of the workpiece. Refer
to Page 30 for more details.
Bevel Edge Cut: A cut made with the blade tilted
to an angle between 0˚ and 45˚ to cut a beveled
edge onto a workpiece. Refer to Page 40 for
more details.
Parallel: Being an equal distance apart at every
point along two given lines or planes (i.e. the
rip fence face is parallel to the face of the saw
blade).
Blade Guard Assembly: Metal or plastic safety
device that mounts over the saw blade. Its function is to prevent the operator from coming into
contact with the saw blade. Refer to Page 34
for more details.
Perpendicular: Lines or planes that intersect and
form right angles (i.e. the blade is perpendicular
to the table surface).
Crosscut: Cutting operation in which the crosscut fence is used to cut across the shortest
width of the workpiece. Refer to Page 39 for
more details.
Dado Blade: Blade or set of blades that are used
to cut grooves and rabbets. Refer to Page 40
for more details. The saw and arbor are not
intended to safely use a larger dado blade.
Dado Cut: Cutting operation that uses a dado
blade to cut a flat bottomed groove into the face
of the workpiece. Refer to Page 40 for more
details.
Featherboard: Safety device used to keep the
workpiece against the rip fence and against
the table surface. Refer to Page 49 for more
details.
Kerf: The resulting cut or gap in the workpiece
after the saw blade passes through during a
cutting operation.
Kickback: An event in which the workpiece is
propelled back towards the operator at a high
rate of speed.
Model G0833P (Mfd. Since 06/17)
Push Stick: Safety device used to push the
workpiece through a cutting operation. Used
most often when rip cutting thin workpieces.
Refer to Page 52 for more details.
Rabbet: Cutting operation that creates an
L-shaped channel along the edge of the
workpiece. Refer to Page 42 for more details.
Rip Cut: Cutting operation in which the rip fence
is used to cut across the widest width of the
workpiece. Refer to Page 38 for more details.
Riving Knife: Metal plate located behind the
blade. It maintains the kerf opening in the wood
when performing a cutting operation. Refer to
Page 37 for more details.
Straightedge: A tool used to check the flatness,
parallelism, or consistency of a surface(s).
Thin Kerf Blade: A blade with a kerf or thickness
that is thinner than a standard blade cannot be
used on this saw.
Through Cut: A cut in which the blade cuts completely through the workpiece. Refer to Page 31
for more details.
-5-
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901
MODEL G0833P 10" HYBRID TABLE SAW WITH RIVING
KNIFE, POLAR BEAR SERIES
Product Dimensions:
Weight.............................................................................................................................................................. 396 lbs.
Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 62 x 39 x 47-3/4 in.
Footprint (Length x Width)............................................................................................................... 20-1/2 x 19-1/2 in.
Shipping Dimensions:
Carton #1
Type.................................................................................................................. Cardboard Box on Wood Skids
Content................................................................................................................................................. Machine
Weight.................................................................................................................................................... 388 lbs.
Length x Width x Height............................................................................................................. 30 x 25 x 42 in.
Must Ship Upright......................................................................................................................................... Yes
Carton #2
Type........................................................................................................................................... Cardboard Box
Content..................................................................................................................................................... Fence
Weight...................................................................................................................................................... 21 lbs.
Length x Width x Height............................................................................................................... 37 x 15 x 7 in.
Must Ship Upright.......................................................................................................................................... No
Carton #3
Type........................................................................................................................................... Cardboard Box
Content....................................................................................................................................................... Rails
Weight...................................................................................................................................................... 33 lbs.
Length x Width x Height................................................................................................................. 64 x 6 x 4 in.
Must Ship Upright.......................................................................................................................................... No
Electrical:
Power Requirement............................................................................................. 115V or 230V, Single-Phase, 60 Hz
Prewired Voltage.................................................................................................................................................. 230V
Full-Load Current Rating....................................................................................................... 16A at 115V, 8A at 230V
Minimum Circuit Size.......................................................................................................... 20A at 115V, 15A at 230V
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length................................................................................................................................................. 6 ft.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................. 6-20 for 230V
Recommended Plug Type...................................................................................................................... 5-20 for 115V
Switch Type..................................................... START/STOP Push Button w/Large Shut-Off Paddle & Disabling Pin
Voltage Conversion Kit............................................................................................................................ P0833P224X
Model G0833P
-6-
The information contained herein is deemed accurate as of 10/13/2017 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 1 OF 3
Model G0833P (Mfd. Since 06/17)
Motors:
Main
Horsepower................................................................................................................................................ 2 HP
Phase............................................................................................................................................ Single-Phase
Amps....................................................................................................................................................... 16A/8A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................. TEFC Capacitor-Start Induction
Power Transfer ....................................................................................................................... Poly-V Belt Drive
Bearings..................................................................................................... Shielded & Permanently Lubricated
Main Specifications:
Main Information
Table Saw Type....................................................................................................................................... Hybrid
Maximum Blade Diameter......................................................................................................................... 10 in.
Arbor Size................................................................................................................................................. 5/8 in.
Arbor Speed...................................................................................................................................... 3850 RPM
Maximum Width of Dado...................................................................................................................... 13/16 in.
Blade Tilt Direction....................................................................................................................................... Left
Max Blade Tilt......................................................................................................................................... 45 deg.
Maximum Depth of Cut At 90 Degrees.................................................................................................. 3-1/8 in.
Maximum Depth of Cut At 45 Degrees................................................................................................ 2-3/16 in.
Max Rip Right of Blade w/Included Fence & Rails.............................................................................. 31-1/2 in.
Max Rip Left of Blade w/Included Fence & Rails................................................................................. 11-3/8 in.
Additional Blade Information
Included Blade Information.................................................................................................................. 10" x 40T
Riving Knife/Spreader Thickness.............................................................................................................. 0.1 in.
Required Blade Body Thickness.............................................................................................. 0.063 – 0.094 in.
Required Blade Kerf Thickness............................................................................................... 0.102 – 0.126 in.
Rim Speed at Max Blade Diameter................................................................................................. 10,074 FPM
Table Information
Floor to Table Height........................................................................................................................... 34-1/4 in.
Table Size with Extension Wings Width.................................................................................................... 40 in.
Table Size with Extension Wings Depth.................................................................................................... 27 in.
Distance Front of Table to Center of Blade......................................................................................... 16-1/4 in.
Distance Front of Table to Blade At Maximum Cut............................................................................. 11-1/2 in.
Main Table Size Thickness.................................................................................................................... 1-1/2 in.
Fence Information
Fence Type.................................................................................... Camlock T-Shape w/High-Low Profile Face
Fence Size Length............................................................................................................................... 34-5/8 in.
Fence Size Width.................................................................................................................................. 4-5/8 in.
Fence Size Height....................................................................................................................................... 3 in.
Fence Rail Type............................................................................................... Square Steel Tubing/Angle Iron
Fence Rail Length............................................................................................................................... 61-7/8 in.
Fence Rail Width......................................................................................................................................... 2 in.
Fence Rail Height.................................................................................................................................. 1-5/8 in.
Miter Gauge Information
Miter Gauge Slot Type.............................................................................................................................. T-Slot
Miter Gauge Slot Size Width..................................................................................................................... 3/4 in.
Miter Gauge Slot Size Height................................................................................................................... 3/8 in.
Model G0833P
The information contained herein is deemed accurate as of 10/13/2017 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
Model G0833P (Mfd. Since 06/17)
PAGE 2 OF 3
-7-
Construction
Table....................................................................................................................... Precision-Ground Cast Iron
Wings...................................................................................................................... Precision-Ground Cast Iron
Cabinet................................................................................................................................... Pre-Formed Steel
Trunnions............................................................................................................................................. Cast Iron
Fence Assembly......................................................................................................... Steel w/Aluminum Fence
Rails........................................................................................................................................................... Steel
Miter Guage Construction.................................................................................................................... Cast Iron
Guard............................................................................................................................................. Clear Plastic
Body/Cabinet Paint Type/Finish................................................................................................ Powder Coated
Arbor Bearings.............................................................................................. Sealed & Permanently Lubricated
Other Related Information
Number of Dust Ports....................................................................................................................................... 2
Dust Port Size............................................................................................................................ 4 in. & 1-1/2 in.
Compatible Mobile Base........................................................................................................................ D2057A
Other Specifications:
Country of Origin ................................................................................................................................................ China
Warranty ........................................................................................................................................................... 1 Year
Approximate Assembly & Setup Time .............................................................................................................. 1 Hour
Serial Number Location ................................................................................................................... Machine ID Label
Sound Rating ..................................................................................................................................................... 87 dB
ISO 9001 Factory .................................................................................................................................................. Yes
Certified by a Nationally Recognized Testing Laboratory (NRTL) .......................................................................... No
Features:
Fully-Enclosed, Quick-Release Blade Guard and Spreader
Quick-Release Riving Knife
Zinc Alloy Hinged Motor Cover
4" & 1-1/2" Dust Ports
Heavy Cast Handwheels
T-Slot Miter Gauge
Poly-V Serpentine Drive Belt System for Reduced Noise/Vibration
Precision-Ground Cast-Iron Table
Large Cabinet-Mounted, Cast-Iron Trunnions
Durable Powder-Coated Finish
Deluxe 2-Position Aluminum Rip Fence
Easy-Glide Fence System with Added Micro-Adjustment Controls
Standard & Dado Table Inserts
Built-In Dust Port on Blade Guard
Included 10" x 40T Carbide-Tipped Blade
Model G0833P
-8-
The information contained herein is deemed accurate as of 10/13/2017 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased.
PAGE 3 OF 3
Model G0833P (Mfd. Since 06/17)
SECTION 1: SAFETY
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
NOTICE
This symbol is used to alert the user to useful information about
proper operation of the machine.
Safety Instructions for Machinery
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, disconnect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machinery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
Model G0833P (Mfd. Since 06/17)
ELECTRICAL EQUIPMENT INJURY RISKS. You
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST. Always disconnect machine from power supply BEFORE making
adjustments, changing tooling, or servicing machine.
This prevents an injury risk from unintended startup
or contact with live electrical components.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
-9-
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hearing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifications—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
-10-
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement during operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for recommended accessories. Using improper accessories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnecting cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intended operation, stop using the machine! Contact our
Technical Support at (570) 546-9663.
Model G0833P (Mfd. Since 06/17)
Additional Safety for Table Saws
Serious cuts, amputation, or death can occur from contact with rotating saw blade during
operation. Workpieces, broken blades, or flying particles thrown by blade can blind or strike
operators or bystanders with deadly force. To reduce the risk of these hazards, operator and
bystanders MUST completely heed the hazards and warnings below.
HAND & BODY POSITIONING. Keep hands
away from saw blade and out of blade path during operation, so they cannot accidentally slip
into blade. Only operate at front of machine and
always stand to side of blade path. Never reach
behind or over blade.
BLADE GUARD. The blade guard protects operator from rotating saw blade. Make sure blade
guard is installed, adjusted correctly, and used
for all possible “through cuts.” Promptly repair or
replace if damaged. Re-install immediately after
operations that require its removal.
RIVING KNIFE. Use riving knife for all “nonthrough cuts.” Make sure it is aligned and positioned correctly. Promptly repair or replace it if
damaged.
KICKBACK. Kickback occurs when saw blade
ejects workpiece back toward operator. Know
how to reduce risk of kickback, and learn how to
protect yourself if it does occur.
FEEDING WORKPIECE. Feeding workpiece
incorrectly increases risk of kickback. Always
allow blade to reach full speed before cutting,
feed workpiece from front of saw, making sure
workpiece is flat against table and a fence, miter
gauge, or other guide is used to feed workpiece
in a straight line. Feed cuts through to completion.
Never start saw with workpiece touching blade
or pull workpiece from behind blade. Never back
workpiece out of cut, move it sideways, or perform
a “freehand” operation. Never plunge cut.
PUSH STICKS/PUSH BLOCKS. To reduce risk
of accidental blade contact, use push sticks/
push blocks whenever possible. In event of an
accident, these will often take damage that would
have occurred to hands/fingers.
Model G0833P (Mfd. Since 06/17)
FENCE. To reduce risk of kickback, make sure
fence remains properly adjusted and parallel with
blade. Always lock fence before using.
CUT-OFF PIECES. To avoid risk of injury due to
blade contact, turn saw OFF and allow blade to
completely stop before removing cut-off pieces
near blade or trapped between blade and table
insert. Never use your hands to move cut-off
pieces away from blade while saw is running.
BLADE ADJUSTMENTS. Adjusting blade height
or tilt during operation increases risk of crashing blade and sending metal fragments flying
with deadly force at operator or bystanders. Only
adjust blade height and tilt when blade is completely stopped and saw is OFF.
CHANGING BLADES. Accidental startup while
changing saw blade can result in serious injury.
To reduce risk of accidental blade contact, always
disconnect power before changing blades.
DAMAGED SAW BLADES. Damaged saw blade
teeth can become deadly projectiles. Never use
blades that have been dropped or damaged.
DADO AND RABBET OPERATIONS. Dado and
rabbeting operations require special attention
since they must be performed with blade guard
removed, which increases risk of blade contact.
DO NOT attempt dado or rabbeting operations
without first reading these sections in this manual.
CUTTING CORRECT MATERIAL. Cutting metal,
glass, stone, tile, etc., increases risk of operator
injury due to kickback or flying particles. Only cut
natural and man-made wood products, laminatecovered wood products, and some plastics. Never
cut materials not intended for this saw.
-11-
Preventing Kickback
•
Below are ways to avoid the most common
causes of kickback:
•
Only cut workpieces with at least one smooth
and straight edge. DO NOT cut warped,
cupped or twisted wood.
•
Keep the blade guard installed and working
correctly for all through cuts.
•
Never attempt freehand cuts. If the workpiece
is not fed parallel with the blade, kickback will
likely occur. Always use the rip fence or miter
gauge to support the workpiece.
•
Make sure the spreader or riving knife is
aligned with the blade. A misaligned spreader
or riving knife can cause the workpiece to
catch or bind, increasing the chance of kickback.
•
Take the time to check and adjust the rip
fence parallel with the blade; otherwise, the
chances of kickback are extreme.
•
The spreader or riving knife maintains the
kerf in the workpiece, reducing the chance of
kickback. Always use the riving knife for all
non-through operations, unless a dado blade
is installed. Always use the spreader with the
blade guard for all through cuts.
•
•
•
-12-
Feed cuts through to completion. Anytime
you stop feeding a workpiece in the middle
of a cut, the chance of kickback is greatly
increased.
Keep the blade guard installed and in good
working order. Only remove it when performing non-through cuts and immediately
re-install the blade guard when finished.
Remember, always use the riving knife for all
non-through operations, unless a dado blade
is installed.
Make multiple, shallow passes when performing a non-through cut. Making a deep
non-through cut will greatly increase the
chance of kickback.
Never move the workpiece backwards or try
to back it out of a cut while the blade is moving. If you cannot complete a cut for some
reason, stop the saw motor and allow the
blade to completely stop before backing the
workpiece out. Promptly fix the condition that
prevented you from completing the cut before
starting the saw again.
Protecting Yourself
From Kickback
Even if you know how to prevent kickback, it
may still happen. Here are some ways to protect yourself if kickback DOES occur:
•
Stand to the side of the blade during every cut.
If kickback does occur, the thrown workpiece
usually travels directly in front of the blade.
•
Wear safety glasses or a face shield. In the
event of kickback, your eyes and face are the
most vulnerable part of your body.
•
Never, for any reason, place your hand
behind the blade. Should kickback occur,
your hand will be pulled into the blade, which
could cause amputation.
•
Use a push stick to keep your hands farther
away from the moving blade. If kickback
occurs, the push stick will most likely take the
damage your hand would have received.
•
Use featherboards or anti-kickback devices
to assist with feeding and prevent or slow
down kickback.
Statistics show that most common accidents among table saw users can be linked
to kickback. Kickback is typically defined as
the high-speed expulsion of stock from the
table saw toward its operator. In addition to
the danger of the operator or others in the
area being struck by the flying stock, it is
often the case that the operator’s hands are
pulled into the blade during kickback.
Model G0833P (Mfd. Since 06/17)
SECTION 2: POWER SUPPLY
Availability
Circuit Information
Before installing the machine, consider the availability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power supply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Full-Load Current Rating at 230V........ 8 Amps
Full-Load Current Rating at 115V...... 16 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid overloading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
Model G0833P (Mfd. Since 06/17)
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, consult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
Circuit Requirements for 230V
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage.......... 208V, 220V, 230V, 240V
Cycle...........................................................60 Hz
Phase............................................ Single-Phase
Circuit Rating....................................... 15 Amps
Plug/Receptacle.............................. NEMA 6-20
Circuit Requirements for 115V
This machine can be converted to operate on a
power supply circuit that has a verified ground
and meets the requirements listed below. (Refer
to Voltage Conversion instructions for details.)
Nominal Voltage..................... 110V, 115V, 120V
Cycle...........................................................60 Hz
Phase............................................ Single-Phase
Circuit Rating....................................... 20 Amps
Plug/Receptacle.............................. NEMA 5-20
-13-
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
For 230V operation: This machine is equipped
with a power cord that has an equipment-grounding wire and a grounding plug (see following figure). The plug must only be inserted into a matching receptacle (outlet) that is properly installed
and grounded in accordance with all local codes
and ordinances.
GROUNDED
6-20 RECEPTACLE
Current Carrying Prongs
6-20 PLUG
Grounding Prong
Figure 4. Typical 6-20 plug and receptacle.
For 115V operation: The plug specified under
“Circuit Requirements for 115V” on the previous page has a grounding prong that must be
attached to the equipment-grounding wire inside
the included power cord. The plug must only be
inserted into a matching receptacle (see following
figure) that is properly installed and grounded in
accordance with all local codes and ordinances.
GROUNDED
5-20 RECEPTACLE
Hot
Neutral
5-20 PLUG
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is necessary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size............................12 AWG
Maximum Length (Shorter is Better).......50 ft.
Grounding Prong
Figure 5. Typical 5-20 plug and receptacle.
-14-
Model G0833P (Mfd. Since 06/17)
Converting Voltage
to 115V
The voltage conversion MUST be performed by
an electrician or qualified service personnel.
The voltage conversion procedure consists of
rewiring the motor and installing the correct plug.
A wiring diagram is provided on Page 76 for your
reference.
IMPORTANT: If the diagram included on the
motor conflicts with the one on Page 76, the motor
may have changed since the manual was printed.
Use the diagram included on the motor instead.
Qty
Items Needed
• Phillips Head Screwdriver #2...................... 1
• Electrical Tape............................. As Needed
• Wire Cutters/Stripper................................... 1
• NEMA 5-20 Plug.......................................... 1
• Circuit Breaker 20A (P0833P224X)............. 1
To convert Model G0833P to 115V:
4. Use wire nuts to connect wires as indicated
in Figure 7. Twist wire nuts onto their respective wires and wrap them with electrical tape
so they will not come loose.
Motor Rewired
for 115V
Connect
Wires with
Nuts Here
GND
Figure 7. Motor rewired to 115V.
Rewired for 110V
5. Close and secure motor junction box.
6. Remove start/stop switch box from the switch
mounting plate.
7. Replace pre-installed 10-amp circuit breaker
(see Figure 8) with a 20-amp circuit breaker
(part #P0833P224X), then re-install START/
STOP switch.
1. DISCONNECT MACHINE FROM POWER!
2. Cut off existing 6-20 plug.
3. Open motor junction box, then
loosen three
110V/220V
wire nuts indicated in Figure 6. MOTOR
Motor Prewired
for 230V
Circuit
Breaker
Loosen
These
Wire
Nuts
Figure 8. Location of circuit breaker.
GND
Figure 6. Location of wire nuts to be loosened
on motor junction box.
Model G0833P (Mfd. Since 06/17)
8. Install a 5-20 plug on power cord, according
to plug manufacturer's instructions.
—If plug manufacturer's instructions are not
available, NEMA standard 5-20 plug wiring
is provided on Page 76.
-15-
SECTION 3: SETUP
Needed for Setup
This machine presents
serious injury hazards
to untrained users. Read
through this entire manual to become familiar with
the controls and operations before starting the
machine!
Wear safety glasses during
the entire setup process!
This machine and its
components are very
heavy. Get lifting help or
use power lifting equipment such as a forklift to
move heavy items.
The following are needed to complete the setup
process, but are not included with the machine:
DescriptionQty
• Additional Person........................................ 1
• Safety Glasses for Each Person................. 1
• Cleaner/Degreaser (Page 20)..... As Needed
• Disposable Shop Rags................ As Needed
• Straightedge 4'............................................ 1
• Wrench or Socket 10mm............................. 1
• Wrench or Socket 13mm............................. 1
• Wrench or Socket 14mm............................. 1
• Phillips Head Screwdriver #2...................... 1
• Dust Collection System............................... 1
• Dust Hose 4"............................................... 1
• Hose Clamps 4".......................................... 2
Unpacking
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage. If items are damaged,
please call us immediately at (570) 546-9663.
IMPORTANT: Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original packaging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
-16-
Model G0833P (Mfd. Since 06/17)
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
A
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
Figure 9. Main table saw unit.
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
Box Contents (Figures 9–11)
Qty
A. Main Table Saw Unit................................... 1
B. Extension Wings......................................... 2
C. Saw Blade 10" x 40T................................... 1
D. Motor Door.................................................. 1
E. Wrench 13/27mm........................................ 1
F. Dado Table Insert........................................ 1
G. Blade Guard Dust Port................................ 1
H. Blade Guard Assembly............................... 1
I. Hex Wrench 6-Piece Set 2.5-8mm............. 1
J. Riving Knife................................................. 1
K. Miter Gauge................................................. 1
L. Dust Hose Adapters.................................... 2
M. Push Stick................................................... 1
N. Dado Blade Arbor........................................ 1
O. Handwheel Handles.................................... 2
P. Handwheel Lock Knobs.............................. 2
Q. Handwheel Handwheel............................... 2
R. Dust Hose 94" x 11⁄ 2"................................... 1
S. Hose Support.............................................. 1
B
Figure 10. Extension wings.
C
F
D
E
G
I
H
K
J
P
O
Q
L
N
M
R
S
Figure 11. Component inventory.
Model G0833P (Mfd. Since 06/17)
-17-
Box Contents Cont'd (Figure 12)
Qty
T. Front Rail Tube 62"...................................... 1
U. Front Rail Tape Scale.................................. 1
V. Rear Rail 55"............................................... 1
W. Front Rail 57"............................................... 1
X. Fence Assembly.......................................... 1
Fasteners (Figure 13)Qty
Y. Cap Screws M10-1.5 x 25
(Wing/Table)................................................ 6
Z. Lock Washers 10mm (Wing/Table)............. 6
AA.Flat Washers 10mm (Wing/Table)............... 6
AB.Flat Head Screws M8-1.25 x 35
(Front Rail/Table)......................................... 4
AC.Lock Washers 8mm (Front Rail/Table)........ 4
AD.Flat Washers 8mm (Front Rail/Table).......... 4
AE.Hex Nuts M8-1.25 (Front Rail/Table)........... 4
AF. Cap Screws M6-1 x 16 (Front Rail/Tube).... 5
AG.Lock Washers 6mm (Front Rail/Tube)......... 5
AH.Flat Washers 6mm (Front Rail/Tube).......... 5
AI. Cap Screws M10-1.5 x 25
(Rear Rail/Table)......................................... 2
AJ. Lock Washers 10mm (Rear Rail/Table)...... 2
AK.Flat Washers 10mm (Rear Rail/Table)........ 2
AL.Cap Screws M8-1.25 x 35
(Rear Rail/Wing).......................................... 2
AM.Flat Washers 8mm (Rear Rail/Wing)........... 4
AN.Lock Washers 8mm (Rear Rail/Wing)......... 2
AO.Hex Nuts M8-1.25 (Rear Rail/Wing)............ 2
AP. Cap Screws M5-.8 x 14 (Switch)................. 2
AQ.Lock Washers 5mm (Switch)....................... 2
AR.Flat Washers 5mm (Switch)........................ 2
AS.Wing Nut M6-1 (Dust Hose Support).......... 1
AT. Flat Washer 6mm (Dust Hose Support)...... 1
AU.Hex Nut M6-1 (Dust Hose Support)............ 1
U
T
V
W
X
Figure 12. Inventory needed to install fence on
Model G0833P.
Y
AB
Z
AC
AD
AA
AE
AF
AI
AG
AJ
AH
AK
AL
AM
AN
AP
AS
AQ
AT
AR
AU
AO
Figure 13. Hardware inventory.
-18-
Model G0833P (Mfd. Since 06/17)
Hardware Recognition Chart
USE THIS CHART TO MATCH UP
HARDWARE DURING THE INVENTORY
AND ASSEMBLY PROCESS.
Flat
Head
Cap
Screw
5mm
5mm
Model G0833P (Mfd. Since 06/17)
-19-
Cleanup
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preventative, but the following steps work well in a wide
variety of situations. Always follow the manufacturer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
•
Disposable rags
•
Cleaner/degreaser (WD•40 works well)
•
Safety glasses & disposable gloves
•
Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2.
Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/degreaser is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
-20-
Gasoline and petroleum
products have low flash
points and can explode
or cause fire if used to
clean machinery. Avo i d
u sing t h e s e p r o d u c t s
to c l e a n m a c hin e r y.
Many cleaning solvents
are toxic if inhaled. Only
work in a well-ventilated
area.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
T23692—Orange Power Degreaser
A great product for removing the waxy shipping grease from the non-painted parts of the
machine during clean up.
Figure 14. T23692 Orange Power Degreaser.
Model G0833P (Mfd. Since 06/17)
Site Considerations
Weight Load
Physical Environment
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest workpiece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
The physical environment where the machine is
operated is important for safe operation and longevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemicals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20%–95% (non-condensing); or
the environment is subject to vibration, shocks,
or bumps.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the maintenance and service described in this manual.
See below for required space allocation.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals, or
other hazards. Make sure to leave enough space
around machine to disconnect power supply or
apply a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
= Power Connection
Wall
68"
Access
Door
Swing at 90º
11/2" Dust Port
4" Dust Port
39"
Min. 30"
Figure 15. Minimum working clearances.
Model G0833P (Mfd. Since 06/17)
-21-
Assembly
4. Slide groove on back of each handwheel over
handwheel shaft pin, as shown in Figure 18.
The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to Needed for Setup and gather
all listed items. To ensure the assembly process
goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if
applicable).
Pin
Handwheel
To assemble table saw:
Groove
1. Using blade height handwheel (refer to
Page 3), raise motor and remove foam shipping block (see Figure 16). Save block for
later machine transport.
Figure 18. Handwheel installed onto shaft pin.
5. Thread a handwheel lock knob into center
of each handwheel and tighten, then thread
a handle onto each handwheel and tighten
(see Figure 19).
Figure 16. Foam shipping block location.
2. Remove switch from saw cabinet, and install
motor door by inserting door pins into hinge
sockets on cabinet (see Figure 17).
Handles
Figure 19. Handwheel installed.
Hinge
Socket
6. Inspect extension wings and main table mating surfaces for burrs or foreign materials that
may inhibit assembly.
For a correct fit, mating edges of table and
wings must be clean, smooth, and flat. If necessary, use a wire brush or file to remove any
flashing, dings, or high spots.
Figure 17. Motor door installed.
3. Before closing door, thoroughly clean heavyduty rust preventative off of gearing inside the
saw and coat these with appropriate metal
protectant (refer to Lubrication on Page 60
for location of gears).
-22-
Model G0833P (Mfd. Since 06/17)
7. While a helper holds wings in place, attach
each extension wing to main table with (3)
M10-1.5 x 25 cap screws, 10mm lock washers, and 10mm flat washers removed in
Step 5 (see Figure 20).
—If outside end of extension wing tilts up,
place strip of masking tape along top edge
of main table to shim end of extension wing
down (see Figure 22).
Main Table
Note: After re-installing wings, remove all
excess masking tape with a razor blade.
x3
Extension
Wing
(1 of 2)
Figure 20. Extension wings installed.
8. Place straightedge across extension wings
and main table to make sure that combined
table surface is flat.
—If combined table surface is flat, skip to
next step.
—If outside end of extension wing tilts down,
place a strip of masking tape along bottom
edge of main table to shim end of extension wing up (see Figure 21).
Figure 22. Masking tape location for adjusting
the extension wing down.
9. Attach front rail to table and extension wings
with (4) M8-1.25 x 35 flat head screws,
8mm flat washers, 8mm lock washers, and
M8-1.25 hex nuts, as shown in Figure 23.
Make sure top of rail is parallel with table top
before fully tightening fasteners.
Front Rail
Equal
x4
Figure 21. Masking tape location for tilting
extension wing up.
Model G0833P (Mfd. Since 06/17)
Figure 23. Front rail installed.
-23-
10. Install front rail tube onto front rail with (5)
M6-1 x 16 cap screws, 6mm flat washers, and 6mm lock washers, as shown in
Figure 24. Finger-tighten fasteners.
14. Install saw blade as outlined in Blade
Installation on Page 33.
15. Place fence on rails (on right hand side of
blade, as shown in Figure 26).
Front Rail Tube
Cam
Foot
Cam
x5
Figure 24. Front rail tube attached to front rail.
Figure 26. Fence installed on rails.
11. While standing at front of table, pull rail tube
toward you as far as possible, then final
tighten fasteners installed in Step 10. This
will help make sure there is enough room for
fence to slide.
Note: Make sure cam foot contacts cam on
fence lock handle before you place fence on
rail; otherwise, fence will not lock onto rail
tube.
12. Attach rear rail to holes on main table using
(2) M10-1.5 x 25 cap screws, 10mm lock
washers, and 10mm flat washers, as shown
in Figure 25. Check to make sure rear rail is
parallel to table and below miter slots before
completely tightening cap screws.
16. Adjust foot at rear of fence so that gap
between fence and table top is even from
front to back.
13. Secure rear rail to extension wings with (2)
M8-1.25 x 35 cap screws, (4) 8mm flat washers, (2) 8mm lock washers, and (2) M8-1.25
hex nuts (see Figure 25).
Rear Rail
x2
x2
Figure 25. Rear rail installed.
-24-
Model G0833P (Mfd. Since 06/17)
17. Slide fence up against right hand edge of
miter slot, and lock it in place. Examine how
fence lines up with miter slot.
Note: It is permissible for back of fence to
pivot outward not more than 1⁄64" from being
parallel with miter slot. This creates a slightly
larger opening between fence and blade, at
rear of blade, to reduce risk of workpiece
binding or burning as it is fed through cut.
Many woodworkers intentionally set up their
fence in this manner. Keep this in mind
before adjusting your fence. For more details,
see Figure 122 on Page 71.
Fence
Miter Slot
Blade
Fence is
Parallel to
Miter Slot,
which is
Parallel to
Blade
18. Carefully slide fence so it barely touches saw
blade and lock it in place.
19. Lightly mark "0" location on fence tube (under
indicator line on pointer window) with a pencil, then remove fence.
20. Peel tape, carefully align "0" mark on scale
with pencil mark you made on fence tube,
and make sure tape is parallel to fence tube
along its length.
21. Re-install fence, move it over to just touch
blade, and verify that indicator line is directly
over "0" mark.
—If you need to correct position of indicator
line, loosen button head screws on pointer
window, adjust pointer window so line is
over "0" mark on tape (see Figure 28),
then secure screws.
Indicator Line
Figure 27. Checking fence parallelism with
blade.
—If fence is still parallel with miter slot, proceed to Step 18.
—If fence is not parallel with miter slot, then
you MUST adjust fence, as described in
Fence Adjustments on Page 69, so that it
is parallel.
Pointer
Window
Figure 28. Aligning rail tape with scale pointer.
22. Install blade guard as outlined on Page 34.
—If miter slot is not parallel with blade, you
must follow procedures described in Miter
Slot to Blade Parallelism on Page 65.
Model G0833P (Mfd. Since 06/17)
-25-
23. Attach switch to bottom left-hand side of front
rail using (2) M5-.8 x 14 cap screws, 5mm
lock washers, and 5mm flat washers, as
shown in Figure 29.
24. Attach dust hose support to rear rail with (1)
M6-1 hex nut, 6mm flat washer, and M6-1
wing nut, as shown in Figure 30, so open
end of hook faces outward.
x2
Open End Faces
Outward
Dust Hose
Support
Figure 30. Dust hose support installed.
Figure 29. Switch installed.
-26-
Model G0833P (Mfd. Since 06/17)
Dust Collection
2. Slide one adapter onto 11⁄2" dust port (see
Figure 32), until it fits snugly.
3. Attach dust hose to dust hose support, then
insert dust port into rear of blade guard
assembly (see Figure 32).
This machine creates a lot of wood chips/
dust during operation. Breathing airborne
dust on a regular basis can result in permanent respiratory illness. Reduce your risk
by wearing a respirator and capturing the
dust with a dust collection system.
Minimum CFM at Dust Port: 500 CFM +
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust collector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to calculate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
Qty
Components Needed:
Dust Hose Adapters 11⁄2".....................................2
Dust Hose 94" x 11⁄2"...........................................1
Dust Hose 4 " (not included)................................1
Hose Clamps 4" (not included)...........................2
Dust Collection System (not included)................1
Dust Port
Hose Support
Blade
Guard
11⁄2" Dust
Port
4" Dust
Port
Figure 32. Dust hose attached to saw, hose
support, and blade guard dust port.
4. Fit 4" dust hose over dust port, as shown in
Figure 33, and tightly secure it in place with
a hose clamp.
Hose Clamp
To connect dust collection hoses:
1. Attach a dust hose adapter to each end of
dust hose (see Figure 31).
4" Dust Hose
Figure 33. Dust hoses attached to port.
Adapters
5. Tug hose to make sure it does not come off.
Note: A tight fit is necessary for proper performance.
Figure 31. Adapters attached to dust hose.
Model G0833P (Mfd. Since 06/17)
-27-
Test Run
4. Insert switch disabling pin through green ON/
START button, as shown in Figure 34.
Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The Troubleshooting table in the
SERVICE section of this manual can help.
The test run consists of verifying the following:
1) The motor powers up and runs correctly, and
2) the safety disabling mechanism on the switch
works correctly.
Serious injury or death can result from
using this machine BEFORE understanding
its controls and related safety information.
DO NOT operate, or allow others to operate,
machine until the information is understood.
Pin
ON / START
Button
OFF / STOP
Paddle
Figure 34. Example of switch disabling pin
inserted into START button.
5. Press green ON/START button to test disabling feature on switch.
—If machine does not start, switch disabling
feature is working as designed.
—If machine does start, immediately stop
machine. The switch disabling feature is
not working correctly. This safety feature
must work properly before proceeding with
regular operations. Call Tech Support for
help.
DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine
may result in malfunction or unexpected results that can lead to serious injury,
death, or machine/property damage.
To test run machine:
1. Lower blade all the way down, and make sure
all tools and objects used during setup are
cleared away from machine.
2. Connect machine to power source.
3. Turn machine ON, verify motor operation,
then turn machine OFF.
-28-
The motor should run smoothly and without
unusual problems or noises.
Model G0833P (Mfd. Since 06/17)
SECTION 4: OPERATIONS
Operation Overview
The purpose of this overview is to provide the novice machine operator with a basic understanding
of how the machine is used during operation, so
the machine controls/components discussed later
in this manual are easier to understand.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual, seek additional training from experienced
machine operators, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Eye injuries, respiratory problems, or hearing loss can occur while operating this
tool. Wear personal protective equipment to
reduce your risk from these hazards.
To complete a typical operation, the operator
does the following:
1. Examines workpiece to make sure it is suitable for cutting.
2. Adjusts blade tilt, if necessary, to correct
angle for desired cut.
3. Adjusts blade height no more than 1⁄4" higher
than thickness of workpiece.
4. Adjusts fence to desired width of cut, then
locks it in place.
5. Checks outfeed side of machine for proper
support and to make sure workpiece can
safely pass all the way through blade without
interference.
6. Puts on safety glasses, respirator, and hearing protection, and locates push sticks/blocks
if needed.
7. Starts saw.
8. Feeds workpiece all the way through blade
while maintaining firm pressure on workpiece
against table and fence, and keeping hands
and fingers out of blade path and away from
blade.
9. Stops machine immediately after cut is
complete.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
Model G0833P (Mfd. Since 06/17)
-29-
Workpiece
Inspection
Some workpieces are not safe to cut on this
machine or may need to be modified before they
can be safely cut. Before cutting, inspect all
workpieces for the following:
•
•
•
Material Type: This machine is intended for
cutting natural and man-made wood products, laminate-covered wood products, and
some plastics. Cutting drywall or cementitious backer board creates extremely fine
dust and may reduce the life of the motor
bearings. This machine is NOT designed to
cut metal, glass, stone, tile, etc.; cutting these
materials with a table saw greatly increases
the risk of injury and damage to the saw or
blade.
Foreign Objects: Nails, staples, dirt, rocks
and other foreign objects are often embedded in wood. While cutting, these objects
can become dislodged and hit the operator,
cause kickback, or break the blade, which
might then fly apart. Always visually inspect
your workpiece for these items. If they can’t
be removed, DO NOT cut the workpiece.
Large/Loose Knots: Loose knots can
become dislodged during the cutting operation. Large knots can cause kickback and
machine damage. Choose workpieces that
do not have large/loose knots or plan ahead
to avoid cutting through them.
•
Wet or “Green” Stock: Cutting wood with a
moisture content over 20% causes unnecessary wear on the blades, increases the risk of
kickback, and yields poor results.
•
Excessive Warping: Workpieces with excessive cupping, bowing, or twisting are dangerous to cut because they are unstable and
may move unpredictably when being cut.
•
Minor Warping: Slightly cupped workpieces
can be safely supported with cupped side
facing the table or fence; however, workpieces supported on the bowed side will rock
during the cut, which could cause kickback.
-30-
Non-Through &
Through Cuts
Non-Through Cuts
A non-through cut is a sawing operation where
the blade does not protrude above the top face of
the wood stock, as shown in the Figure below.
Figure 35. Example of a non-through cut.
Examples of non-through cuts include dadoes
and rabbets. Non-through cuts have a higher
risk of injury from kickback because the blade
guard must be removed. However, the riving knife
MUST be installed because it still provides some
protection.
IMPORTANT: When making non-through cuts
with a dado blade, do not attempt to cut the full
depth in one pass. Instead, take multiple light
passes to reduce the load on the blade.
A dado blade smaller than 10" will require removal
of the riving knife, because the riving knife will be
higher than the blade.
Model G0833P (Mfd. Since 06/17)
Through Cuts
A through cut is a sawing operation in which the
workpiece is completely sawn through, as shown
in the Figure below. Examples of through cuts are
rip cuts, cross cuts, miter cuts, and beveled cuts.
The blade guard assembly MUST be used when
performing through cuts.
Blade Selection
This section on blade selection is by no means
comprehensive. Always follow the saw blade
manufacturer's recommendations to ensure safe
and efficient operation of your table saw.
Ripping Blade Features:
Best for cutting with the grain
•
•
20-40 teeth
•
Flat-top ground tooth profile
•
Large gullets for large chip removal
Figure 36. Example of a through cut (blade
guard not shown for illustrative clarity).
Blade Requirements
When choosing a main blade, make sure the
blade size meets the requirements listed below.
The thickness of the blade body and teeth can be
measured with calipers or any precision measuring device.
Blade Size Requirements:
• Body Thickness: 0.063"–0.094" (1.8-2.4mm)
• Kerf (Tooth) Thickness: 0.102"–0.126"
(2.6-3.2mm)
• Riving Knife Thickness: 0.1" (2.5mm)
• Blade Size Required for Riving Knife: 10"
Flat
Top
Blade
Figure 37. Ripping blade.
Crosscut blade features:
•
Best for cutting across the grain
•
60-80 teeth
•
Alternate top bevel tooth profile
•
Small hook angle and a shallow gullet
Alternate
Top
Bevel
Figure 38. Crosscutting blade.
Model G0833P (Mfd. Since 06/17)
-31-
Combination blade features:
•
Designed to cut both with and across grain
•
40-50 teeth
•
Alternate top bevel and flat, or alternate top
bevel and raker tooth profile
•
Teeth are arranged in groups
•
Gullets are small and shallow (similar to a
cross-cut blade), then large and deep (similar
to a ripping blade
Alternate
Top
Bevel
and
Flat
Thin Kerf Blade: A blade with thinner kerf than
a standard blade. Since the spreader/riving knife
included with this table saw is sized for standard
blades, thin kerf blades cannot be used on this
saw unless they meet the Blade Requirements
specified in this manual; otherwise, they will
increase the risk of kickback.
Dado Blades
Stacked Dado Blade (see below): Multiple
blades are stacked together to control the cutting
width. Stacked dado blades are more expensive
than wobble blades, but typically produce higher
quality results.
Wobble Dado Blade: A single blade mounted at
a slight angle on an arbor hub. The blade angle is
adjustable on the hub, and the width of the dado
cut is controlled by the angle setting of the blade.
Figure 39. Combination blade.
Laminate blade features:
•
Best for cutting plywood or veneer
•
40-80 teeth
•
Triple chip tooth profile
•
Very shallow gullet
Figure 41. Stacked dado blade.
Triple
Chip
Blade
Figure 40. Laminate blade.
-32-
Model G0833P (Mfd. Since 06/17)
Blade Installation
Review this section, even if your saw blade came
pre-installed.
4. While pressing arbor lock, use included arbor
wrench to loosen and remove arbor nut,
flange, and blade (see Figure 43). Arbor nut
has right-hand threads; rotate counterclockwise to loosen.
To install blade:
1. DISCONNECT MACHINE FROM POWER!
2. Raise arbor all the way up, then remove
blade guard and spreader/riving knife (see
Pages 34 & 37) and table insert.
To reduce risk of injury, always disconnect
power to saw before changing blades. Since
blade is sharp, use extra care and wear
gloves when installing it.
Figure 43. Example of removing table saw
blade.
5. Install new blade, flange, and arbor nut on
arbor, as shown in Figure 44, with upper
teeth facing front of saw.
3. Push arbor lock (see Figure 42) in and turn
blade until it locks in place.
Arbor Lock
Figure 42. Location of arbor lock.
Figure 44. Blade order of installation and teeth
facing correct direction.
6. Secure blade with arbor lock, then tighten
flange and arbor nut against blade with arbor
wrench. DO NOT overtighten.
7. Re-install table insert (see Page 72) and
blade guard (see Page 34) or riving knife
(see Page 37).
Model G0833P (Mfd. Since 06/17)
-33-
Blade Guard
Assembly
The term "blade guard" refers to the assembly
that consists of the clear polycarbonate shield
and dust enclosure, the spreader, and the antikickback pawls on each side of the spreader
(see Figure 45). Each of these components have
important safety functions during the operation of
the saw.
Dust Enclosure
In order to work properly, the spreader
cannot be bent or misaligned with the blade.
If the spreader gets accidentally bent, take
the time to straighten it or just replace it.
Using a bent or misaligned spreader will
increase the risk of kickback! Refer to Page
67 to check or adjust alignment if necessary.
Installing Blade Guard & Spreader
Tools Needed
Qty
Hex Wrench 3mm............................................... 1
Straightedge....................................................... 1
To install blade guard and spreader:
Anti-Kickback
Pawl
Clear Shield
Spreader
Figure 45. Blade guard assembly components.
Guard
The clear polycarbonate guard allows the operator to see the blade cut the workpiece during
operation. This guard is designed to lift as the
workpiece is pushed into the blade and remain in
contact with the workpiece throughout the entire
cut.
The guard reduces injury risk by providing a barrier around the blade that prevents accidental
contact and contains flying wood chips.
To ensure that the guard does its job effectively,
the guard must always be in the downward position against the table during idle operation, and
the hinge mechanism must be maintained in good
working condition so the guard can freely pivot
up and down to accommodate the height of the
workpiece and return to the table surface.
Spreader
The spreader is a metal plate that prevents the
newly cut kerf of the workpiece from pinching the
backside of the blade, causing kickback.
1. DISCONNECT MACHINE FROM POWER!
2. Install table insert, then raise blade all the
way up.
3. Slide knurled knob out (see Figure 46) and
rotate it so it engages upper bracket.
Upper
Bracket
Knurled
Knob
Locking Pin
Adjustment
Block
Figure 46. Knurled knob used to secure
spreader.
4. Slide blade guard spreader all the way down
into adjustment block, then rotate knurled
knob so it disengages bracket and locking pin
engages hole in center of spreader.
5. Give spreader an upward tug to verify that it
is locked.
The spreader also acts as a barrier behind the
blade to shield hands from being pulled into the
blade if a kickback occurs.
-34-
Model G0833P (Mfd. Since 06/17)
The blade guard, when properly installed,
should be set up similarly to Figure 47. It
should pivot freely up and down and return to
the table in the resting position. It should also
swing up high enough to accommodate the
workpiece.
8. Install blade guard dust port and dust collection hose, as shown in Figure 49, and attach
hose to dust collection port on table saw body
(refer to Page 27).
Dust Port
6. Adjust flat head cap screws (see Figure 47)
to make sure table insert is flush with table
(use a straightedge as a guide).
Dust Hose
Figure 49. Dust port and dust collection hose
installed on blade guard.
Anti-Kickback Pawls
Figure 47. Blade guard installed.
The anti-kickback pawls allow the workpiece to
travel in only one direction. If the workpiece moves
backwards, such as during a kickback, the pawls
will dig into the workpiece to slow or stop it.
7. While lifting up on one side of blade guard
and right spreader pawl, place straightedge
against blade and spreader, making sure
straightedge does not touch a blade tooth.
To work properly, the pawls must return to their
resting position after pivoting, as shown in
Figure 50, and they must NOT be engaged in the
arresting hooks.
Flat Head Cap Screw (1 of 4)
When properly aligned, spreader/riving
knife will be in "Alignment Zone," shown in
Figure 48, and will be parallel with blade.
Alignment
Zone
Arresting Hooks
Pawl
Spreader or
Riving Knife
Blade
Straightedge
Figure 48. Spreader/riving knife alignment zone.
—If spreader/riving knife is not inside alignment zone and not parallel with blade,
then it needs to be adjusted. Proceed to
"Adjusting Alignment" on Page 68.
Model G0833P (Mfd. Since 06/17)
Figure 50. Pawls in resting position.
If the pawls fail to return to the resting position, the
pivot area may need to be cleaned or the spring
may have been dislodged or broken and will need
to be fixed/replaced.
-35-
Disabling Pawls
You might disable the pawls if you are concerned
about them scratching a delicate workpiece, or
if you believe that they will obstruct a narrow
workpiece and cause feeding difficulty or loss of
control. Use your best judgment before retracting
the pawls, as they are provided for your safety.
We do not recommend disabling pawls during normal operations unless absolutely
necessary. In most situations, disabling
pawls will increase your risk of serious personal injury in event of a kickback.
Enabling Pawls
To enable the pawls, lift up on each pawl and
move them outward and down until they both
touch the table surface, as shown in Figure 50
on Page 35.
When to Use the Blade Guard
The blade guard assembly MUST always be
installed on the saw for all normal through cuts
(those where the blade cuts all the way through
the thickness of the workpiece). If the blade
guard is removed for specific operations, always
immediately replace it after those operations are
complete.
When Not to Use the Blade Guard
The pawls are sharp and can lacerate fingers
or hands. Use caution, and wear leather
gloves when handling the pawls to reduce
risk of injury.
To disable pawls:
1. DISCONNECT MACHINE FROM POWER!
2. Rotate one or both arresting hooks downward, then place pawls on each of the hooks,
as shown in Figure 51.
The blade guard cannot be used on any nonthrough cuts (those in which the blade does
not cut all the way through the thickness of the
workpiece).
IMPORTANT: Whenever the blade guard cannot
be used, the riving knife must be installed.
Sometimes the blade guard or its components
can get in the way when cutting very narrow
workpieces or other specialized cuts. Because
the blade guard is provided to decrease your risk
of injury, it should not be used if it gets in the way
of making a safe cut. Use good judgment!
Pawl
Arresting Hooks
(One Shown)
Figure 51. Pawls disabled.
-36-
Model G0833P (Mfd. Since 06/17)
Riving Knife
The riving knife works in the same manner as
the spreader on the blade guard assembly. It is a
metal plate that prevents the newly cut workpiece
from pinching the backside of the blade and causing kickback.
The key difference between the spreader and the
riving knife is that the riving knife mounts below
the blade's highest point of rotation, as shown in
Figure 52.
To ensure that riving knife works safely, it
MUST be aligned with and correctly adjusted to blade. Refer to Page 67 to check or
adjust riving knife alignment.
How to Install the Riving Knife
The riving knife is installed in a similar manner
to the blade guard and spreader. Refer to Blade
Guard Assembly on Page 34 for installation
instructions.
When to Use the Riving Knife
Minimum 1mm
Maximum 5mm
Height Difference
Figure 52. Height difference between riving knife
and blade.
The height difference between the riving knife and
the blade allows the workpiece to pass over the
blade during non-through cuts (those in which the
blade does not cut all the way through the thickness of the workpiece).
The riving knife acts as a barrier behind the blade
to reduce the risk of hands being pulled into the
blade if a kickback occurs.
The riving knife must be kept within the range
shown in Figure 53. For that reason, we only
recommend using a 10" blade for operations that
require use of the riving knife.
Use the riving knife for all non-through cuts made
with a standard table saw blade (i.e., dadoes or
rabbet cuts, and when using a tenoning jig), or
when using a 10" diameter dado blade.
Also, use the riving knife for those special operations where the blade guard or its components
get in the way of safe operation, such as with very
narrow cuts.
When Not to Use the Riving Knife
DO NOT use the riving knife with a dado blade
that has a diameter smaller than 10" in diameter.
Otherwise, the riving knife height will exceed the
blade height and the workpiece will hit the riving
knife during the cut, forcing the operator into a
dangerous situation of trying to turn the saw off
with the workpiece stuck halfway through the cut.
In addition, although it is possible to use the riving knife for through cutting operations, the blade
guard assembly offers far more injury protection
and risk reduction than the riving knife. Therefore,
we strongly recommend that you use the blade
guard assembly instead of the riving knife for
through cuts.
Top Distance
Minimum 3mm
Maximum 8mm
Bottom Distance
Minimum 3mm
Maximum 8mm
Figure 53. Allowable top and bottom distances
between riving knife and blade.
Model G0833P (Mfd. Since 06/17)
-37-
Ripping
6. Set fence to desired width of cut on scale.
"Ripping" means cutting with the grain of a natural
wood workpiece. In man-made materials such as
MDF or plywood, ripping means cutting lengthwise.
Serious injury can be caused by kickback.
Kickback is a high-speed ejection of stock
from table saw toward an operator. The
operator or bystanders may be struck by flying stock, or operator’s hands can be pulled
into blade during kickback.
7. Adjust blade height so highest saw tooth protrudes no more than 1⁄4" above workpiece.
8. Set up safety devices such as featherboards
or other anti-kickback devices, making sure
no safety devices are contacting blade.
9. Plug saw into power source, turn it ON, and
allow it to reach full speed.
Note: Jointed edge of workpiece must slide
against fence during cutting operation.
10. Use push stick to feed workpiece through
saw blade, as shown in Figure 55, until
workpiece is completely beyond saw blade.
To make a rip cut:
1. Review Preventing Kickback on Page 12
and take necessary precautions to reduce
likelihood of kickback.
2. If using natural wood, joint one long edge of
workpiece on a jointer.
3. DISCONNECT MACHINE FROM POWER!
4. Ensure that blade guard/spreader is installed.
5. Loosen fence knobs (see Figure 54), remove
rip fence, then re-install in vertical position for
thicker workpieces, or in horizontal position
for thinner workpieces and angled cuts where
blade is tilted over fence. Lift fence up and
tighten each fence knob.
Featherboard
Figure 55. Typical ripping operation.
Turn saw OFF and allow blade to come to a
complete stop before removing cutoff piece.
Failure to follow this warning could result in
severe lacerations or amputation.
Vertical
Knob
(1 of 3)
Horizontal
Figure 54. Rip fence positions.
-38-
Keep blade guard installed and in down
position. Failure to do this could result in
serious personal injury or death.
Model G0833P (Mfd. Since 06/17)
Crosscutting
Miter Cuts
"Crosscutting" means cutting across the grain of
a natural wood workpiece, usually with a miter
saw. In other man-made materials, such as MDF
or plywood, crosscutting means cutting across the
width of the workpiece.
A miter is an angled crosscut. Miters are usually
cut in the same manner as crosscuts, using the
miter gauge and a predetermined mark on the
workpiece.
To make a crosscut using miter gauge:
1. DISCONNECT MACHINE FROM POWER!
2. Ensure that blade guard/spreader is installed.
3. To avoid kickback, move rip fence aside and
position miter gauge, adjusted to 90°, in a
miter slot.
4. Adjust blade height so teeth protrude no
more than 1⁄4" above workpiece.
5. Slide miter gauge near blade and adjust
workpiece so blade will cut on waste side of
line.
To perform a miter cut:
1. DISCONNECT MACHINE FROM POWER!
2. Ensure that blade guard/spreader is installed.
3. Determine angle of cut. If angle needs to be
very precise, use a protractor to set miter
gauge to blade.
4. Place face of miter gauge against edge
of workpiece and place bar across face of
workpiece. Use bar as a guide to mark your
cut, as shown in Figure 57.
6. Plug in table saw, turn it ON, and allow it to
reach full speed.
7. Hold workpiece firmly against face of miter
gauge (as shown in Figure 56), and ease it
through blade until workpiece is completely
past saw blade.
Figure 57. Example of marking miter line.
Figure 56. Typical crosscutting operation.
5. Place miter gauge back into slot and hold
workpiece firmly against miter gauge body.
Slide miter gauge near blade and adjust
workpiece so blade will cut on waste side of
line.
6. Proceed to make cut in same manner as
described in Crosscutting instructions.
Turn saw OFF and allow blade to come to a
complete stop before removing cutoff piece.
Failure to follow this warning could result in
severe lacerations or amputation.
Model G0833P (Mfd. Since 06/17)
-39-
Blade Tilt/Bevel Cuts
When the blade tilt collar bolts are properly adjusted (as described starting on Page 63), the blade
tilt handwheel allows the operator to tilt the blade
to the left, between 0° and 45°. This is used most
often when cutting bevels, compound miters, or
chamfers. Figure 58 shows an example of the
blade when tilted to 45°.
The Model G0833P can accommodate dado
blades up to 10" in diameter. However, you MUST
install the included riving knife while using a 10"
diameter dado blade, as it provides a barrier
behind the blade and reduces the risk of hands
being pulled into the blade if kickback occurs.
DO NOT use the riving knife if you install a dado
blade smaller than 10" in diameter. Otherwise,
the riving knife height will exceed the blade height
and the workpiece will hit the riving knife during
the cut, forcing the operator into a dangerous
situation and trying to turn the saw off with the
workpiece stuck halfway through the cut.
Installing a Dado Blade
1. DISCONNECT MACHINE FROM POWER!
2. Remove table insert, blade guard assembly
or riving knife, arbor nut, flange, and saw
blade.
Figure 58. Example of blade tilted to 45° for
bevel cutting (blade guard only removed for
clarity.
4. Install dado table insert.
Dado Cutting
Commonly used in furniture joinery, a dado is a
straight channel cut in the face of the workpiece.
Dadoes are "non-through" cuts that can be made
with a dado blade or a standard saw blade. The
Figure below shows a cutaway view of a dado cut
being made with a dado blade.
Dado Blade
Workpiece
3. Attach and adjust dado blade system according to dado blade manufacturer’s instructions, and secure with included dado blade
flange and arbor nut.
Fence
DO NOT make through cuts with a dado
blade. The extra width of a dado blade
will increase the risk of kickback during a
through cut. Dado blades are only intended
for non-through cuts. Failure to heed this
warning could result in serious injury.
Never try to cut a warped board by holding it down against the table. If kickback
occurs, your hand could be pulled into the
blade, resulting in accidental contact with
the rotating blade, causing severe lacerations or amputation.
Figure 59. Example of a dado being cut with a
dado blade.
-40-
Model G0833P (Mfd. Since 06/17)
Cutting Dadoes with a Dado Blade
Because dado blades are much wider than standard blades, they place a greater amount of force
against the workpiece when cutting. This additional force increases the risk of kickback, requiring
the operator to take additional steps when cutting
to keep their injury risk at an acceptable level.
Dado blades have a higher risk of kickback
than normal blades because their larger size
applies stronger forces to the workpiece.
This risk increases relative to the depth and
width of the cut. To minimize your risk of
serious personal injury, ensure that stock
is flat and straight, and make multiple light
cuts (rather than one deep cut) to achieve
the desired cutting depth.
The Figure below demonstrates the sequential
process of making multiple, light cuts that get
progressively deeper. The actual number of cuts
used should be determined by workpiece hardness, total dado depth, and feed rate. In general, if
you hear the motor slow down during the cut, you
are cutting too deep or feeding too fast.
Dado Blade
Cut 1
Fence
Workpiece
To cut a dado with a dado blade:
1. DISCONNECT MACHINE FROM POWER!
2. Adjust dado blade to desired depth of cut.
3. Adjust distance between fence and inside
edge of blade, as shown in Figure 59 on
Page 40, to dado length of a workpiece.
—If
dadoing across workpiece, use miter
gauge and carefully line up desired cut with
dado blade. To reduce kickback, DO NOT
use fence in combination with miter gauge.
4. Reconnect saw to power source.
5. Turn saw ON. Blade should run smoothly,
with no vibrations.
6. When blade has reached full speed, perform
test cut with scrap piece of wood.
7. If cut is satisfactory, repeat cut with actual
workpiece.
Cutting Dadoes with a Standard
Blade
A ripping blade (described on Page 38) is typically
the best blade to use when cutting dadoes with a
standard blade because it removes sawdust very
efficiently.
To use a standard saw blade to cut dadoes:
1. DISCONNECT MACHINE FROM POWER!
Cut 2
Fence
Workpiece
Cut 3
Workpiece
Fence
3. Raise blade up to desired depth of cut (depth
of dado channel desired).
4. Set saw up for type of cut you need to make,
depending on whether it is a rip cut (Page 38)
or crosscut (Page 39).
Finished
Dado Cut
Workpiece
2. Mark width of dado cut on workpiece. Include
marks on edge of workpiece so cut path can
be aligned when workpiece is lying on table.
Fence
Figure 60. Example of dado being cut with
multiple light cuts, instead of one deep cut.
Model G0833P (Mfd. Since 06/17)
-41-
5. Align blade to cut one side of dado, as shown
in Figure 61.
Blade
Cut 1
Fence
Workpiece
Figure 61. First cut for a single-blade dado.
6. Reconnect saw to power source and turn saw
ON. Allow blade to reach full speed, then perform cutting operation.
7. Repeat cutting operation on other side of
dado, as shown in Figure 62.
Rabbet Cutting
Commonly used in furniture joinery, a rabbet is an
L-shaped groove cut in the edge of the workpiece.
Rabbets can be cut with either a dado blade or a
standard saw blade.
Rabbet cutting on the edge of the workpiece
with a dado blade requires a sacrificial fence
(see Figure 64). Make the sacrificial fence the
same length as the fence and 3⁄4" thick. Attach it
to the fence with screws or clamps, making sure
they are all secure and tight. Raise the blade into
the sacrificial fence to the height needed.
Rip Fence
Sacrificial
Fence
Cut 2
Blade
Workpiece
Dado Insert
Fence
Blade Cut-Out
Figure 64. Example of sacrificial fence.
Figure 62. Second cut for a single-blade dado.
8. Make additional cuts (see Figure 63) in center of dado to clear out necessary material.
Dado is complete when channel is completely cleared out.
Cuts 3+
Workpiece
Fence
Figure 63. Additional single-blade dado cuts.
-42-
When using a dado blade, the included dado
table insert must be installed and used during rabbeting operations.
Dado blades have a higher risk of kickback
than normal blades because their larger size
applies stronger forces to the workpiece.
This risk increases relative to the depth and
width of the cut. To minimize your risk of
serious personal injury, ensure that stock
is flat and straight, and make multiple light
cuts (rather than one deep cut) to achieve
the desired cutting depth.
Model G0833P (Mfd. Since 06/17)
Cutting Rabbets with a Standard
Blade
Always use push sticks, featherboards,
push paddles and other safety accessories
whenever possible to increase safety and
control during operations which require
that blade guard be removed from saw.
ALWAYS replace blade guard after dadoing
is complete.
Cutting Rabbets with a Dado Blade
1. DISCONNECT MACHINE FROM POWER!
2. Adjust dado blade to height needed for rabbeting operation. When cutting deep rabbets,
take more than one pass to reduce risk of
kickback.
3. Adjust fence and align workpiece to perform
cutting operation, as shown in Figure 65.
A ripping blade is typically the best blade to use
for cutting rabbets when using a standard blade
because it removes sawdust very efficiently. (See
Page 31 for blade details.) Also, a sacrificial fence
is not required when cutting rabbets with a standard blade.
To cut rabbets with a standard blade:
1. DISCONNECT MACHINE FROM POWER!
2. Ensure that riving knife and standard table
insert are installed.
3. Mark width of rabbet cut on edge of workpiece,
so you can clearly identify intended cut while
it is laying flat on saw table.
4. Raise blade up to desired depth of cut (depth
of rabbet channel desired).
5. Stand workpiece on edge, as shown in
Figure 66, then adjust fence so blade is
aligned with inside of your rabbet channel.
Sacrificial Fence
Workpiece
Fence
Blade
Workpiece
Dado Blade
Fence
Figure 65. Rabbet cutting.
4. Reconnect saw to power source and turn saw
ON. When blade has reached full speed, perform a test cut with a scrap piece of wood.
—If cut is satisfactory, repeat cut with
workpiece.
Model G0833P (Mfd. Since 06/17)
Figure 66. Example of rabbet cutting with a
standard blade.
—If workpiece is very tall, or is unstable when
placed against fence, lay it flat on table and
use a dado blade to perform rabbet cut.
-43-
Resawing
Resawing operations require proper procedures to avoid serious injury. Extra care
must be taken to prevent kickback when
resawing. Any tilting or movement of the
workpiece away from the fence will cause
kickback. Be certain that stock is flat and
straight. Failure to follow these warnings
could result in serious personal injury.
45
15
30
DO NOT place a tall board on edge to perform a rabbet cut with a standard blade.
Workpieces that are too tall to properly support with fence can easily shift during operation and cause kickback. Instead, place
stock flat on saw and perform rabbet cut
with a dado blade, as instructed on Page 42.
6. Reconnect saw to power source, then perform cut.
7. Lay workpiece flat on table, as shown in
Figure 67, adjust saw blade height to intersect with first cut, then perform second cut to
complete rabbet.
Blade
Workpiece
Fence
Resawing is the process of cutting a thick piece
of stock into one or more thinner pieces. Although
resawing can be done with a table saw, we
strongly recommend that you use a bandsaw
instead.
A bandsaw is the ideal machine for resawing, and
resawing with one is fairly easy and safe. A table
saw is not intended for resawing, and resawing
with one is difficult and dangerous due to the
increased risk of kickback from binding and deep
cuts, and the increased risk of injury from having
to remove the guard.
If you insist on resawing with a table saw, DO NOT
do so without using a resaw barrier and wearing a
full face shield. The following instructions describe
how to build a resaw barrier and add an auxiliary
fence to your standard fence, to reduce the risk
injury from resawing on a table saw.
Note: To determine the maximum resawing height
for this table saw, find the maximum blade height,
then double it and subtract 1⁄ 8".
Figure 67. Example of second cut to create a
rabbet.
-44-
Model G0833P (Mfd. Since 06/17)
Making Resaw Barrier
Making Auxiliary Fence
When resawing, the resaw barrier acts in tandem
with the rip fence to provide tall support for the
workpiece. This minimizes the probability of it
binding against the blade and causing kickback.
An auxiliary fence is necessary if you are resawing
a workpiece that is taller than it is wide. The fence
should be no less than 1⁄2" shorter than the board
to be resawn.
Tools Needed:
Qty
Table Saw...........................................................1
Jointer and Planer........................ Recommended
Clamps................................................ 2 Minimum
Drill.....................................................................1
Drill Bits 1⁄8", 9⁄64"........................................ 1 Each
Countersink Bit....................................................1
The fence should be similar to the one in Figure 69
when installed.
Auxiliary Fence
Fence
Components Needed for Resaw Barrier:
Wood* 3⁄4" x 51⁄2" x Length of Fence....................1
Wood* 3⁄4" x 3" x Length of Fence.......................1
Wood Screws #8 x 2" . .......................................4
Wood Glue..........................................As Needed
*Only use furniture-grade plywood, kiln-dried
hardwood, or HDPE plastic to prevent warping.
M6-1 Flat
Head Cap Screw
To build a resaw barrier:
1. Cut your wood pieces to size specified above.
If you are using hardwood, cut pieces oversize, then joint and plane them to correct size
to make sure they are square and flat.
2. Pre-drill and countersink four holes approximately 3⁄8" from bottom of 51⁄2" tall wood piece.
3. Glue end of 3" board, clamp boards at a 90°
angle with larger board in vertical position, as
shown in Figure 68, then fasten together with
wood screws.
#8 x 2"
Wood Screw
⁄4"
3
Assembled Auxiliary Fence
Figure 69. Example of auxiliary fence attached
to Model G0833P fence face.
Tools Needed:
Qty
Clamps................................................................2
Drill.....................................................................1
Drill Bit 7⁄32" .........................................................1
Countersink Drill Bit.............................................1
Hex Wrench 5mm................................................1
Ruler....................................................................1
⁄4"
3
Assembled
Resaw Barrier
Figure 68. Resaw barrier.
Model G0833P (Mfd. Since 06/17)
-45-
Components Needed:
Flat Head Cap Screws M6-1 x (Auxiliary Fence
Width + Fence Tube Width).........................3
Wood* 3⁄4" x 4" x Length of Fence.......................1
*Only use furniture-grade plywood, kiln-dried
hardwood, or HDPE plastic to prevent warping.
To build an auxiliary fence:
1. Cut auxiliary fence board to size. If you are
using hardwood, cut board oversize, then
joint and plane board to correct size to make
sure board is square and flat.
2. Unthread (3) knobs and (3) flat washers
securing fence face to fence tube shown in
Figure 70, then remove fence.
Flat Washer
Knob
(1 of 3
3. Place auxiliary fence board against fence
tube. Place a thin metal shim (such as a
ruler) between table and bottom of auxiliary
fence board to ensure adequate clearance
between fence board and table. Clamp in
position.
4. Mark location of three mounting holes on
Auxiliary Fence
auxiliary fence and remove auxiliary fence
board from fence tube.
Fence
5. Using 7⁄32" drill bit, drill mounting holes in
auxiliary fence board. Countersink holes 1⁄16"
deep so head of flat head cap screws sits
slightly beneath face of auxiliary fence board.
6. Insert (3) flat head cap screws through holes
in auxiliary fence board (see Figure 69) and
secure with knobs and flat washers removed
earlier. The end result should be similar to
Figure
71.
M6-1 Flat
Head Cap Screw
Figure 70. Location of knobs and flat washers
securing fence to fence tube.
Figure 71. Example auxiliary fence attached to
Assembled
Auxiliary Fence
included
fence.
-46-
Model G0833P (Mfd. Since 06/17)
Resawing Operations
The table saw motor is pushed to its limits when
resawing. If the motor starts to bog down, slow
down your feed rate. Motor overloading and blade
wear can be reduced by using a ripping blade.
Ripping blades are designed to clear the sawdust
quickly.
5. Place workpiece against auxiliary fence and
slide resaw barrier against workpiece, as
shown in Figure 72. Now clamp resaw barrier to top of table saw at both ends.
Workpiece
Components Needed for Resawing:
Zero-Clearance Insert.........................................1
Ripping Blade 10"................................................1
Clamps................................................................2
Shop-Made Auxiliary Fence................................1
Shop-Made Resaw Barrier..................................1
You may experience kickback during this
procedure. Stand to the side of the blade
and wear safety glasses and a full face
shield to prevent injury when resawing.
To perform resawing operations:
1. DISCONNECT MACHINE FROM POWER!
2. Remove standard table insert and blade
guard assembly.
Resaw
Barrier
Auxiliary
Fence
Fence
Figure 72. Ideal resaw workpiece setup.
6. Lower blade completely below table-top, and
slide workpiece over blade to make sure it
moves smoothly and fits between resaw barrier and fence.
7. Raise blade approximately 1 inch, or close to
half the height of workpiece (see Figure 73),
whichever is less.
Workpiece
3. Install a ripping blade, install riving knife,
lower blade below table surface, then install
zero-clearance table insert.
4. Attach auxiliary fence and set it to desired
width.
(Front View)
Resaw
Barrier
Auxiliary
Fence
Fence
/8" Connection
1
Note: When determining correct width,
don't forget to account for blade kerf and
inaccuracy of fence scale while auxiliary
fence is installed.
Figure 73. Ideal completed resaw cut.
Model G0833P (Mfd. Since 06/17)
-47-
8. Plug in table saw, turn it ON, and use a push
stick or push block to feed workpiece through
blade, using a slow and steady feed rate.
Note: We recommend making a series of
light cuts that get progressively deeper, to
reduce the chance of stalling the motor.
9. Flip workpiece end-for-end, keeping same
side against fence, and run workpiece through
blade.
10. Repeat Steps 7–9 until blade is close to half
the height of board to be resawn. The ideal
completed resaw cut will leave a 1⁄8" connection when resawing is complete as shown in
Figure 73 on Page 47. Leaving a 1⁄8" connection will reduce risk of kickback.
The danger of kickback increases relative to
the depth of a cut. Reduce the risk of kickback by making multiple passes to achieve
the desired depth of cut. Failure to follow
these warnings could result in serious personal injury.
Always use push sticks or push paddles to
increase safety and control during operations which require that the blade guard
and spreader must be removed from the
saw. ALWAYS replace blade guard after
resawing is complete.
11. Turn OFF table saw, then separate parts of
workpiece and hand plane remaining ridge to
remove it.
12. When finished resawing, remove resaw barrier and auxiliary fence, then re-install blade
guard/spreader or riving knife and standard
table insert.
-48-
Model G0833P (Mfd. Since 06/17)
SECTION 5: SHOP MADE SAFETY
ACCESSORIES
Featherboards
Easily made from scrap stock, featherboards
provide an added degree of protection against
kickback, especially when used together with
push sticks. They also maintain pressure on the
workpiece to keep it against the fence or table
while cutting, which makes the operation easier
and safer because the cut can be completed without the operator’s hands getting near the blade.
The angled ends and flexibility of the fingers allow
the workpiece to move in only one direction.
Making a Featherboard
We recommend using a bandsaw for making fingers in the next step because it tends
to be safer. A table saw can be used, but it
will over-cut the underside of the ends, produce a thicker kerf, and require you to stop
the blade half-way through the cut, which
can be dangerous.
3. Make a series of end cuts with the grain
3
⁄8"–1⁄4" apart and 2"–3" long, as shown in
Figure 74 (A). Alternatively, start cuts at 2"-3"
deep, then make them progressively deeper,
as shown in Figure 74 (B).
This sub-section covers the two basic types of
featherboards: 1) Those secured by clamps, or 2)
those secured with the miter slot.
Material Needed for Featherboard
Hardwood 3⁄4" x 3" x 10" (Minimum)
Hardwood 3⁄4" x 6" x 28" (Maximum)...................1
Additional Material Needed for Mounting
Featherboard in Miter Slot
Hardwood 3⁄8" x (Miter Slot Width) x 5"L ............1
Wing Nut 1/4"-20...................................................1
Flat Head Screw 1⁄4"-20 x 2"................................1
Flat Washer 1⁄4"-20..............................................1
To make a featherboard:
1. Cut a hardwood board approximately 3⁄4" thick
to size. The length and width of the board
can vary according to your design. Most
featherboards are 10"–28" long and 3"–6"
wide. Make sure the wood grain runs parallel with the length of the featherboard, so the
fingers you will create in Step 3 will bend
without breaking.
10" (Minimum)
30°
A
Kerf
⁄16"-1⁄8"
⁄8"
3
1
2"-3"
Initial Cut
2"-3"
B
Kerf
⁄16"-1⁄8"
1
⁄8 "
3
Progressively
Longer Cuts
Figure 74. Patterns for featherboards
(top view shown).
IMPORTANT: Cuts made across the grain result
in weak fingers that easily break when flexed.
When made correctly, the fingers should withstand flexing from moderate pressure. To test the
finger flexibility, push firmly on the ends with your
thumb. If the fingers do not flex, they are likely too
thick (the cuts are too far apart).
2. Cut a 30º angle at one end of the board.
Only Steps 1–3 are required to make a
clamp-mounted featherboard. Refer to Page
51 for instructions on clamping.
Model G0833P (Mfd. Since 06/17)
-49-
4. Rout a 1⁄ 4"–3⁄ 8" wide slot 4"–5" long in
workpiece and 1"–2" from short end of featherboard (see Figure 75).
/4"-3/8" Slot
1
1"-2"
7. Mark a 4" line through center of countersunk
hole in center, then use a jig saw with a narrow blade to cut it out.
8. Assemble miter bar and featherboard with
a 1⁄4"-20 x flat head screw, flat washer, and
a wing nut or a star knob (see Figure 77).
Congratulations! Your featherboard is complete.
4"-5"
Wing Nut
Figure 75. Slot routed in featherboard.
Flat Washer
Featherboard
5. Cut a miter bar approximately 5" long that will
fit in table miter slot, as shown in Figure 76.
(Top View)
3
5"
1
/4" Hole
Countersink on Bottom
4" Slot
Figure 76. Miter bar pattern.
Tip: Consider making miter bar longer for
larger featherboards—approximately half the
length of total featherboard—to support force
applied to the featherboard during use.
6. Drill a 1⁄4" hole in center of bar, then countersink bottom to fit a 1⁄4"-20 flat head screw.
-50-
Miter Bar
Flat Head Screw
(Side View)
5"
/8"
(Side View)
Figure 77. Assembling miter slot featherboard
components.
Note: The routed slot, countersink hole, and
flat head screw are essential for miter bar to
clamp into miter slot. When wing nut is tightened, it will draw flat head screw upward into
countersunk hole. This will spread sides of
miter bar and force them into walls of miter
slot, locking featherboard in place.
Tip: The length of the flat head screw depends
on thickness of featherboard—though 11⁄2" to
2" lengths usually work.
Now, proceed to Mounting Featherboard in
Miter Slot on Page 51.
Model G0833P (Mfd. Since 06/17)
Mounting Featherboards w/Clamps
Mounting Featherboard in Miter Slot
1. Lower saw blade, then adjust fence to desired
width and secure it.
1. Lower saw blade, then adjust fence to desired
width and secure it.
2. Place workpiece against fence, making sure
it is 1" in front of the blade.
2. Place workpiece evenly against fence, making sure it is 1" in front of blade.
3. Place a featherboard on table away from
blade so all fingers point forward and contact
workpiece (see Figure 78).
3. Slide featherboard miter bar into miter slot,
making sure fingers slant toward blade, as
shown in Figure 79.
Fence Featherboard
Clamp
Blade
Featherboard
Clamp
Table
Featherboard
FigureWorkpiece
79. Featherboard installed in miter slot
and supporting workpiece for ripping cut.
Figure 78. Example of featherboards secured
with clamps.
4. Secure featherboard to table with a clamp.
5. Check featherboard by pushing it with your
thumb to ensure it is secure.
—­If featherboard moves, tighten clamp more.
6. Optional: If cutting long workpieces, it may
be beneficial to use a second featherboard
attached to fence to keep board firmly against
table while feeding.
4. Position fingered edge of featherboard
against edge of workpiece, so that all fingers
contact workpiece. Slide featherboard toward
blade until first finger is nearly even with end
of workpiece, which should be 1" away from
blade.
5. Double-check workpiece and featherboard
to ensure they are properly positioned, as
described in Step 4. Then secure featherboard to table. Check featherboard by hand
to make sure it is tight.
Model G0833P (Mfd. Since 06/17)
Note: The featherboard should be placed
firmly enough against workpiece to keep it
against fence but not so tight that it is difficult
to feed workpiece.
-51-
Push Sticks
Supporting: A second push stick can be used to
keep the workpiece firmly against the fence while
cutting. When using a push stick in this manner,
only apply pressure before the blade; otherwise,
pushing the workpiece against or behind the
blade will increase the risk of kickback (see "Push
Stick Prohibition Zone" in the Figure below).
When used correctly, push sticks reduce the risk
of injury by keeping hands away from the blade
while cutting. In the event of an accident, a push
stick can also absorb damage that would have
otherwise happened to hands or fingers.
Push Stick
Prohibition
Zone
Using a Push Stick
Use push sticks whenever your hands will get
within 12" of the blade. To maintain control when
cutting large workpieces, start the cut by feeding
with your hands then use push sticks to finish
the cut, so your hands are not on the end of the
workpiece as it passes through the blade.
Push Stick
Store Push
Stick Here
for Easy
Access
Supporting
Blade
Path
Feeding: Place the notched end of the push stick
against the end of the workpiece (see Figure 81
below), and move the workpiece into the blade
with steady downward and forward pressure.
Push Stick
Feeding
Figure 80. Using push sticks to rip narrow stock.
Making a Push Stick
Use this template to make
your own push stick.
90º
15 3
/4 "
Figure 81. Side view of a push stick in-use.
Mi
nim
um
Le
ng
Cut here to
push 1⁄4" stock
th
SIZING: Push stick
must be at least 15 3⁄4"
long. Use 1⁄2"–3⁄4" thick
material.
Cut here to push 1⁄2" stock
Notch for placing on
corners of workpieces
⁄ " Grid
12
Notch to help
prevent hand
from slipping
MATERIAL: Only use
hardwood, sturdy plywood,
or high-density plastic. Do
not use softwood that may
break under pressure or
metal that can break teeth
from the blade!
SANDING: Sand
edges to remove
rough edges and
increase comfort.
Figure 82. Template for a basic shop-made push stick (not shown at actual size).
-52-
Model G0833P (Mfd. Since 06/17)
Push Blocks
The notched end of the push block is then used
to push the workpiece the rest of the way through
the cut, keeping the operator's hands at a safe
distance from the blade. A push stick is often
used at the same time in the other hand to support the workpiece during the cut (see Using a
Push Stick on previous page).
When used correctly, a push block reduces the
risk of injury by keeping hands away from the
blade while cutting. In the event of an accident,
a push block often takes the damage that would
have otherwise happened to hands or fingers.
Push Stick
Prohibition
Zone
Using a Push Block
A push block can be used in place of or in addition to a push stick for feeding workpieces into the
blade. Due to their design, push blocks allow the
operator to apply firm downward pressure on the
workpiece that could not otherwise be achieved
with a push stick.
Push Stick
Supporting
Blade
Path
The push block design on this page can be used
in two different ways (see inset Figure below).
Typically, the bottom of the push block is used
until the end of the workpiece reaches the blade.
Feeding
Push
Block
Figure 84. Using a push block and push stick to
make a rip cut.
CAUTION: Bottom
of handle must be
at least 4" above
bottom of push
block to keep
hand away
from blade.
Making a Push Block
Use this template to make your own push block.
Handle for
firm grip
Figure 83. Side view of a push block in use.
Notch for use
as a push stick
Make push block with
1⁄2"–3⁄4" thick material
4"
CAUTION: Only use hardwood, sturdy plywood,
or high-density plastic. Do not use softwood that
may break under pressure or metal that can break
teeth from the blade!
/4"–1/2"
1
Lip for pushing workpiece
⁄ " Grid
12
9"−10" Minimum Length
Figure 85. Template for a shop-made push block (shown at 50% of full size).
Model G0833P (Mfd. Since 06/17)
-53-
Narrow-Rip Auxiliary
Fence & Push Block
Note: We recommend cutting hardwood
board oversize, then jointing and planing it
to correct size to make sure board is square
and flat. Only use furniture-grade plywood or
kiln-dried hardwood to prevent warping.
There are designs for hundreds of specialty jigs
that can be found in books, trade magazines, and
on the internet. These types of jigs can greatly
improve the safety and consistency of cuts. They
are particularly useful during production runs
when dozens or hundreds of the same type of cut
need to be made.
2. Pre-drill and countersink eight pilot holes 3⁄8"
from bottom of 3" wide board, then secure
boards together with eight #8 x 11⁄2" wood
screws, as shown in Figure 87.
#8 x 11⁄2"
Wood Screw
⁄ " Hardwood
3⁄4" Plywood
34
The narrow-rip auxiliary fence and push block
system shown in this section is an example of
a specialty jig that can be made to increase the
safety of very narrow rip cuts.
Material Needed for Narrow Rip Auxiliary
Fence & Push Block
Hardwood 3⁄4" x 3" x Length of Fence.................1
Plywood 3⁄4" x 51⁄4" x Length of Fence.................1
Wood Screws #8 x 11⁄2".......................................8
Figure 87. Location of pilot holes.
Material Needed for Push Block
Hardwood or Plywood 3⁄4" x 15" x 55⁄8"................1
Hardwood or Plywood 3⁄4" x 10" x 5"–9" .............1
Cyanoacrylate Wood Glue..........................Varies
Wood Screws #8 x 11⁄2".......................As Needed
3. Using 3⁄4" material you used in previous steps,
cut out pieces for push block per dimensions shown in Figure 88; for handle, cut a
piece 10" long by 5"–9" high and shape it as
desired to fit your hand.
Making a Narrow-Rip Push Block for
an Auxiliary Fence
1. Cut a piece of 3⁄4" thick plywood 5 1⁄4" wide
and as long as your table saw fence; cut a
piece of 3⁄4" thick hardwood 3" wide and as
long as your table saw fence, as shown in
Figure 86.
Completed
Fence
5 5⁄8"
15"
⁄ " Hardwood
Length of Table
Saw Rip Fence
⁄ " Plywood
34
3"
Length of Table
Saw Rip Fence
Lip
⁄"
38
5 1⁄4"
12 1⁄2"
34
Handle
2 1⁄2"
⁄"
58
2 1⁄2"
⁄"
38
Figure 88. Push block dimensions and
construction.
4. Attach handle to base with #8 x 11⁄2" wood
screws, and attach lip to base with cyanoacrylate-type wood glue.
51⁄4"
Figure 86. Auxiliary fence dimensions.
-54-
Model G0833P (Mfd. Since 06/17)
Using Auxiliary Fence & Push Block
1. Place auxiliary fence on table and clamp
it to fence at both ends, then adjust distance between auxiliary fence and blade—
this determines how wide workpiece will be
ripped (see Figure 89).
Auxilliary Fence
Blade
Workpiece
Cutting Width
Figure 89. Adjusting ripping distance between
blade and auxiliary fence.
2. Install blade guard, then secure spreader
pawls in upright position, as shown in Figure
51 on Page 36, so they do not interfere with
push block lip.
Auxilliary Fence
Blade
Workpiece
Push Stick
for Side
Support
Push
Block
Blade Path
Figure 90. Push block in position to push
workpiece through blade.
4. Turn saw ON, then begin ripping workpiece
using a push stick for side support.
5. As workpiece nears end of cut, place push
block on auxiliary fence with lip directly
behind workpiece, then release push stick
just before blade.
6. Guide workpiece rest of way through cut with
push block, as shown in Figure 91.
Release
Push Stick
Before Blade
Push
Block
Lip
Blade Path
Keep the blade guard installed and in the
down position. Failure to do this could
result in serious personal injury or death.
3. Place workpiece 1" behind blade and evenly
against table and auxiliary fence.
Model G0833P (Mfd. Since 06/17)
Figure 91. Ripping with push block.
Turn OFF the saw and allow blade to come
to a complete stop before removing cut-off
piece. Failure to follow this warning could
result in serious personal injury.
-55-
Outfeed & Support
Tables
One of the best accessories for improving the
safety and ease of using a table saw is simply placing a large table (outfeed table) behind the saw to
catch the workpiece (see Figure 92). Additionally,
another table to the left of the saw (support table)
can also help support large workpieces so they
can be cut safely and accurately.
Support
Table
Outfeed
Table
Crosscut Sled
A crosscut sled (see Figure 93) is a fantastic
way to improve the safety and accuracy of crosscutting on the table saw. Most expert table saw
operators use a crosscut sled when they have
to crosscut a large volume of work, because the
sled offers substantial protection against kickback
when crosscutting.
Crosscut
Sled
Figure 93. Example of crosscut sled.
Figure 92. Example of outfeed & support tables.
-56-
Model G0833P (Mfd. Since 06/17)
ACCESSORIES
SECTION 6: AFTERMARKET
ACCESSORIES FROM GRIZZLY
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by Grizzly.
NOTICE
G1163P—1HP Floor Model Dust Collector
G0710—1HP Wall-Mount Dust Collector
H4340—3.0 Micron Upgrade Bag
Excellent point-of-use dust collectors that can
be used next to the machine with only a small
amount of ducting. Specifications: 450 CFM, 7.2"
static pressure, 2 cubic foot bag, and 30 micron
filter. Motor is 1HP, 110V/220V, 14A/7A.
Model G0710
Refer to our website or latest catalog for
additional recommended accessories.
D4206—Clear Flexible Hose 4" x 10'
W1034—Heavy-Duty Clear Flex Hose 4" x 10'
W1015—Y-Fitting 4" x 4" x 4"
W1017—90° Elbow 4"
W1019—Hose Coupler (Splice) 4"
W1317—Wire Hose Clamp 4"
W1007—Plastic Blast Gate 4"
W1053—Anti-Static Grounding Kit
We've hand picked a selection of commonly used
dust collection components for machines with 4"
dust ports.
D4206
D4216
W1317
Model G1163P
Figure 95. Point-of-use dust collectors.
Forrest Dado Blades
H4756— 8", 24 Teeth, 1⁄4"–29⁄32" Groove
T23267—8", 24 Teeth, 3⁄16"–1⁄4" Groove
The world's finest dado head clean cuts all
your grooves! No splintering when cross-cutting
oak, ply veneers and melamine. Perfect for flatbottomed grooves. No staggered steps or round
bottoms like a wobble-dado leaves! Cuts in all
directions - rip, cross-cut, miter, any depth. Cuts
all sized grooves 1⁄4" through 29 ⁄ 32" increments.
W1017
W1007
W1053
Figure 94. Dust collection accessories.
T23279—Zero Clearance Insert for G0833P
Figure 96. H4756 Dado Blade.
order online at www.grizzly.com or call 1-800-523-4777
Model G0833P (Mfd. Since 06/17)
-57-
H8029—5 Pc. Safety Kit
Comes with four table saw jigs, essential for safe
operation. Includes two push blocks, push stick,
featherboard, and combination saw and router
gauge. Featherboard fits 3 ⁄ 8" x 3 ⁄4" miter slots.
T26419—Syn-O-Gen Synthetic Grease
Formulated with 100% pure synthesized hydrocarbon basestocks that are compounded with special
thickeners and additives to make Syn-O-Gen
non-melt, tacky, and water resistant. Extremely
low pour point, extremely high temperature oxidation, and thermal stability produce a grease that is
unmatched in performance.
Figure 97. H8029 5 Pc. Safety Kit.
Forrest Woodworker II Saw Blades
T20778—10", 20 Teeth
T20779—10", 40 Teeth
T23527—10", 48 Teeth
Hailed as the Cadillac of all blades, Forrest saw
blades have become legendary for their ability to
leave highly polished, finish ready surfaces on
nearly everything they cut. Made in USA.
With this all purpose blade for table saws you can
rip and crosscut 1" 2" rockhards and softwoods,
resulting in a smooth-as-sanded surface. With
20° face hook, ply veneers will crosscut with no
bottom splinter at moderate feed rates. Double
hard and 40% stronger C4 carbide will give up
to 300% longer life between sharpenings. Ends
blade changing (one blade does rip, combo and
crosscut), second-step finishing and cutting 1⁄ 16"
oversize to allow for resurfacing. Buy and sharpen
one blade instead of 3 (24T rip, 50T combination
and 80T crosscut). 5 ⁄ 8" arbor, 1⁄ 8" kerf.
Figure 99. T26419 Syn-O-Gen Synthetic
Grease.
D3096—Featherboard
Reduce the risk of kick-back without the use of
clamps. These featherboards are designed to lock
into 3 ⁄ 8" and 3 ⁄4" miter gauge slots and are adjustable for various stock widths.
Figure 100. D3096 Featherboard.
Figure 98. Forrest Woodworker II Saw Blade.
order online at www.grizzly.com or call 1-800-523-4777
-58-
Model G0833P (Mfd. Since 06/17)
SECTION 7: MAINTENANCE
To prevent serious personal injury from shock
or accidental startup,
always disconnect power
from machine before
doing any maintenance.
Schedule
For optimum performance from your machine,
follow this maintenance schedule and refer to any
specific instructions given in this section.
Daily Check:
• Loose mounting bolts/arbor nut.
• Damaged saw blade.
• Worn or damaged wires.
• Any other unsafe condition.
Weekly Maintenance:
• Clean table surface and miter slot grooves.
• Clean and protect cast-iron table.
• Clean rip fence.
Cleaning &
Protecting
Cleaning the Model G0833P is relatively easy.
Vacuum excess wood chips and sawdust, and
wipe off the remaining dust with a dry cloth. If any
resin has built up, use a resin-dissolving cleaner
to remove it.
Protect the unpainted cast-iron table by wiping it
clean after every use—this ensures moisture from
wood dust does not remain on the bare metal
surface. Keep the table rust-free with regular
applications of products like G96 ® Gun Treatment,
SLIPIT®, or Boeshield® T-9.
G5562—SLIPIT® 1 Qt. Gel
G5563—SLIPIT® 12 Oz. Spray
G2871—Boeshield® T-9 12 Oz. Spray
G2870—Boeshield® T-9 4 Oz. Spray
H3788—G96 ® Gun Treatment 12 Oz. Spray
H3789—G96 ® Gun Treatment 4.5 Oz. Spray
Monthly Maintenance:
• Clean/vacuum dust buildup from inside cabinet and off motors.
• Check/replace belt for proper tension, damage or wear (Page 74).
Every 6–12 Months:
• Lubricate trunnion slides (Page 60).
• Lubricate worm gear and bull gear (Page 60).
• Lubricate leadscrew (Page 60).
Model G0833P (Mfd. Since 06/17)
Figure 101. Recommended products for protecting unpainted cast iron/steel parts on machinery.
-59-
Lubrication
It is essential to clean components before lubricating them because dust and chips build up on
lubricated components and make them hard to
move. Simply adding more grease to them will not
yield smooth moving components.
Clean the components in this section with an oil/
grease solvent cleaner and shop rags.
If you thoroughly clean the components in this
section before lubricating them, the result will
be silky smooth movement when turning the
handwheels, which will result in much higher
enjoyment on your part!
Worm Gear, Bull Gear & Leadscrew
Lubrication Type.... T26419 or NLGI#2 Equivalent
Amount...........................................................Dab
Lubrication Frequency......................6–12 Months
Clean away any built up grime and debris from the
worm gear, bull gear, and leadscrew (see Figures
103–104) with a wire brush, rags, and mineral
spirits. Allow the components to dry, then apply a
thin coat of grease to them.
Bull Gear
The following are the main components that
need to be lubricated:
•
•
Trunnion Slides
Worm Gear, Bull Gear, and Leadscrew
Items Needed
Qty
NLGI#2 Grease or Equivalent............ As Needed
Mineral Spirits..................................... As Needed
Clean Shop Rags............................... As Needed
Worm Gear
Figure 103. Worm and bull gear location.
Leadscrew
Trunnion Slides
Lubrication Type.... T26419 or NLGI#2 Equivalent
Amount...................................................1-2 Dabs
Lubrication Frequency......................6–12 Months
Clean out the front and rear trunnion slides with
mineral spirits and a rag, then apply grease into
each groove. Move the blade tilt back-and-forth to
spread the grease (see Figure 102).
Figure 104. Leadscrew location.
Trunnion
Slides
Figure 102. Trunnion slide locations.
-60-
Model G0833P (Mfd. Since 06/17)
SECTION 8: SERVICE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If
you need replacement parts or additional help with a procedure, call our Technical Support. Note: Please
gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Symptom
Possible Cause
Possible Solution
Machine does not 1. Locking pin installed in switch.
start, or power 2. Machine circuit breaker tripped.
supply
breaker 3. Power supply circuit breaker tripped or fuse
immediately trips
blown.
after startup.
4. Plug/receptacle at fault/wired incorrectly.
5. Motor wires connected incorrectly.
6. Wiring open/has high resistance.
7. START/STOP switch or circuit breaker at
fault.
8. Start capacitor at fault.
9. Motor at fault.
1. Remove locking pin from START button.
2. Reset circuit breaker on switch.
3. Ensure circuit is sized correctly and free of shorts.
Reset circuit breaker or replace fuse.
4. Test for good contacts; correct the wiring.
5. Correct motor wiring connections (Page 76).
6. Check/fix broken, disconnected, or corroded wires.
7. Replace switch/circuit breaker.
Machine stalls or is 1. Feed rate/cutting speed too fast.
underpowered.
2. Workpiece material unsuitable for machine.
3. Motor overheated; tripping machine circuit
breaker.
4. Blade dull or incorrect for type of cut.
5. Belt(s) slipping.
6. Motor wired incorrectly.
7. Pulleys slipping on shaft or misaligned.
1. Decrease feed rate/cutting speed.
2. Only cut wood/ensure moisture is below 20%.
3. Clean motor/let cool, and reduce workload. Reset
breaker.
4. Use correct, sharp blade; reduce feed rate.
5. Tension/replace belt(s).
6. Wire motor correctly (Page 76).
7. Tighten/replace loose pulley; ensure pulleys are
aligned (Page 74)
8. Test/repair/replace.
9. Test/repair/replace.
10.Test all legs for power/replace if faulty.
11.Adjust/replace centrifugal switch if available.
12.Test/repair/replace.
8. Run capacitor at fault.
9. Motor bearings at fault.
10.Contactor not energized/has poor contacts.
11.Centrifugal switch at fault.
12.Motor at fault.
Machine has
vibration or noisy
operation.
8. Test/replace if faulty.
9. Test/repair/replace.
1. Inspect/replace damaged bolts/nuts, and re-tighten
with thread-locking fluid.
2. Replace warped/bent blade; resharpen dull blade.
Blade at fault.
Belt(s)/pulley(s) worn, loose, or misaligned. 3. Inspect/replace belts with new matched set. Realign/
replace shaft, pulley, set screw, and key (Page 74).
4. Tighten/replace.
Motor mount loose/broken.
Machine incorrectly mounted/resting on 5. Tighten mounting bolts; relocate/shim machine.
floor.
6. Retighten/replace arbor pulley.
Arbor pulley loose.
7. Fix/replace fan cover; replace loose/damaged fan.
Motor fan rubbing on fan cover.
8. Replace arbor housing bearings; replace arbor.
Arbor bearings at fault.
9. Test by rotating shaft; grinding/loose shaft requires
Motor bearings at fault.
bearing replacement.
1. Motor or component loose.
2.
3.
4.
5.
6.
7.
8.
9.
Model G0833P (Mfd. Since 06/17)
-61-
Symptom
Possible Cause
2. Rails dirty or sticky.
1. Remount rip fence. Adjust fence (Page 71) to ensure
adjustment screws are not too tight.
2. Clean and wax rails.
1. Improper feeding technique.
2. Fence not parallel with blade.
1. Learn/use proper feeding technique.
2. Adjust fence parallel with blade (Page 70).
Rip fence does not 1. Rip fence mounted/adjusted incorrectly.
move smoothly.
Material moves
away from fence
when ripping.
Possible Solution
Blade not parallel 1. Blade warped/damaged/dull.
with miter slot.
1. Replace blade (Page 33).
Blade tilt does not 1. 45°/90° stop out of adjustment. Sawdust 1. Adjust 45°/90° stop (Page 63). Remove sawdust
stop at 45°/90°.
built up in/on trunnions.
from trunnions. Clean and re-lubricate as necessary.
1. Clean sawdust or debris out of trunnion slides.
Blade hits table 1. Sawdust/debris stuck in trunnion slides.
insert when tilting to 2. Table/trunnion assembly mount position not 2. Adjust table or trunnion mounting position (Page 65).
45°.
correct.
3. Miter slot not parallel with blade.
3. Make miter slot parallel with blade; shim table
(Page 65).
4. Correctly install blade (Page 33).
4. Blade incorrectly installed.
Board binds or
burns when feeding
through table saw.
1.
2.
3.
4.
5.
Blade warped/damaged/dull.
Too many teeth on blade for cutting type.
Fence not parallel to blade.
Miter slot not parallel with blade.
Riving knife or spreader not correctly aligned
with blade.
6. Spreader not correctly aligned with blade.
Handwheel binds or 1. Lock knob is tightened.
is difficult to move.
2. Handwheel shaft pins are wedged.
Replace blade (Page 33).
Change blade to one with fewer teeth.
Adjust fence parallel with blade (Page 70).
Make miter slot parallel with blade (Page 65).
Adjust riving knife or spreader into alignment with
blade (Page 67).
6. Adjust spreader into alignment with blade (Page 67).
1.
2.
3.
4.
5.
1. Loosen lock knob.
2. Remove handwheel and adjust shaft pins.
Blade too close to 1. Blade or arbor washers incorrectly installed 1. Verify blade and arbor washers are correctly installed
insert.
in the required positions.
on arbor.
2. Table/trunnion assembly mount position not 2. Adjust table or trunnion mounting position (Page 65).
correct.
Blade will not go
beneath table
surface.
1. Roll pin/set screw in worm gear contacting 1. Tighten roll pins and set screws in the worm gear.
geared trunnion.
Blade will not move 1. Set screw on worm gear is loose or missing. 1. Tighten or replace set screw.
up or down.
Too much sawdust 1. Blade guard removed.
blown back toward
operator.
2. Too many air leaks in cabinet for proper
dust collection.
3. Dust collection system clogged or lacks
required CFM at machine.
4. Fence not parallel with blade (pressure at
blade backside).
5. Miter slot not parallel with blade.
1. Re-install blade guard for maximum safety and dust
control (Page 34).
2. Seal leaks in cabinet or around blade guard dust
port.
3. Remove clog; revise ducting layout for improved
suction; use a different dust collector.
4. Adjust fence parallel with blade (Page 70).
Workpiece catches 1. Table/dado insert out of adjustment.
on table/dado insert
or table throat during
cutting operation.
1. Adjust table/dado insert so it is perfectly flush with
table surface (Page 72).
-62-
5. Make miter slot parallel with blade (Page 65).
Model G0833P (Mfd. Since 06/17)
Blade Tilt Stops
The table saw features stop collars that stop the
blade exactly at 45° and 90° when tilting it with
the handwheel. The stops have been set at the
factory and should require no adjustments, unless
you notice that your cuts are not accurate.
Note: The tilt scale reads "0" when the blade is
90° to the table.
Tools Needed
Qty
90° Square......................................................... 1
45° Square......................................................... 1
Hex Wrench 2.5mm............................................ 1
Hex Wrench 3mm............................................... 1
Setting 90° Stop Collar
1. DISCONNECT MACHINE FROM POWER!
2. Raise blade as high as it will go, then tilt it
toward 0° until it stops and cannot be tilted
any more.
3. Place 90° square against table and blade so
it contacts blade evenly from bottom to top,
as shown in Figure 105. Make sure blade
tooth does not obstruct placement of square.
Blade
Indicator
Figure 106. Tilt indicator arrow.
—If blade is not 90° to table, you will need
to adjust 90° stop collar. Proceed to next
step.
4. Tilt blade away from 0° by about 5°, so there
is room for 90° stop collar to move.
5. Open motor door, loosen set screws shown
in Figure 107, then thread 90° stop collar
one turn away from trunnion bracket. This will
allow you to square blade in next step.
Set Screws
Trunnion
Bracket
90° Square
Table
90° Stop
Collar
Figure 107. 90° stop collar and set screws.
Figure 105. Checking blade at 90°.
—If blade is 90° to table, then adjustments do
not need to be made. Make sure tilt indicator arrow shown in Figure 106 points to 0°
mark on scale. Adjust position by loosening
button head screw, moving indicator with
your fingers, then tightening screw.
Model G0833P (Mfd. Since 06/17)
6. Place square against blade, as shown in
Figure 105, then adjust blade until it is perfectly square to table.
7. Without turning blade tilt leadscrew, fingertighten 90° collar against trunnion bracket,
then tighten two set screws to secure collar
position.
-63-
8. Repeat Steps 2–3 to verify that collar adjustment you made was correct. When adjustment is satisfactory, close motor door.
Setting 45° Stop Collar
5. Open right access cover, loosen set screws
on 45° stop collar (see Figure 109), then turn
collar one turn away from trunnion bracket.
This will allow you to adjust blade to exactly
45° in next step.
1. DISCONNECT MACHINE FROM POWER!
2. Raise blade as high as it will go, then tilt it
towards 45° until it stops and cannot be tilted
any more.
Set Screws
3. Place a 45° square against table and blade
so it contacts blade evenly from bottom to
top, as shown in Figure 108. Make sure a
blade tooth does not obstruct placement of
square.
45° Stop Collar
45° Square
Blade
Table
Figure 108. Checking blade at 45°.
—If blade is 45° to table, then adjustments do
not need to be made.
Trunnion
Bracket
Figure 109. Location of 45° stop collar (right
access cover removed).
6. Place a 45° square against blade, as shown
in Figure 108, then adjust blade until it is
exactly 45° to table.
7. Without turning blade tilt leadscrew, fingertighten 45° stop collar against trunnion bracket, then tighten two set screws to secure collar position.
8. Repeat Steps 2–3 to verify that collar adjustment you made was correct. When adjustment is satisfactory, close right access cover.
—If blade is not 45° to table, you will need
to adjust 45° stop collar. Proceed to next
step.
4. Tilt blade to 30°, so there is room for stop
collar to move.
-64-
Model G0833P (Mfd. Since 06/17)
Miter Slot to Blade
Parallelism
Your table saw will give the best results if the
miter slot and the rip fence are adjusted parallel to the blade. If either of these are not exactly
parallel, your cuts and your finished work will be
lower in quality, but more importantly, the risk of
kickback will be increased.
Tools Needed
Qty
Adjustable Square.............................................. 1
Marker................................................................ 1
Metal Shim Stock............................... As Needed
Hex Wrench 6mm............................................... 1
To adjust blade parallel to miter slot:
3. With end of adjustable square just touching
tip, lock square in place. Now, mark carbide tip with a marker where you made this
measurement.
The saw blade is sharp. Use extra care or
wear gloves when handling the blade or
working near it.
4. Rotate marked blade tip to other end of table
insert.
5. Slide adjustable square down to other end
of table insert and compare distance from
marked blade tip to end of adjustable square,
as shown in Figure 111.
1. DISCONNECT SAW FROM POWER!
2. Tilt blade to 0°, then use an adjustable square
to measure distance from miter slot to a carbide tip on blade, as shown in Figure 110.
Make sure that face of adjustable square is
even along miter slot.
STEP B
Blade tilted to 0º
Front
B
Figure 111. Measuring distance from miter slot
to carbide tip on opposite side of table insert.
—If blade tip measurement is same on both
sides, go to Step 8.
STEP A
Blade tilted to 0º
—If blade tip does not touch end of adjustable square similar to first measurement,
table will need to be adjusted. Proceed to
Step 6.
Front
Figure 110. Example of adjusting blade to miter
slot.
Model G0833P (Mfd. Since 06/17)
-65-
6. Loosen (4) table mounting bolts securing
table top to base (see Figure 112), and lightly
tap table in direction needed to square table
to blade.
Mounting
Bolts
10. Refer to Figures 113–114 for shim placement. If distance A is shorter than B, shim(s)
will need to be placed under corners #1 and
#2. If distance of B is shorter than A, shim(s)
will need to be placed under corner #3. Very
thin shim stock works well.
STEP A
#1
Front
Figure 112. Location of table mounting bolts
(table omitted for clarity).
7. Repeat Steps 2–6 until blade and miter slot
are parallel, then retighten table mounting
bolts.
#3
#2
Figure 113. Shim procedure diagram A.
STEP B
8. Tilt blade to 45° and recheck miter slot-toblade parallelism.
—If blade is still parallel with miter slot, no
additional adjustments need to be made.
—If blade is parallel with miter slot at 0° but
not at 45°, one end of table will need to
be shimmed higher with metal shim stock.
Continue to Step 9.
9. Loosen (4) table mounting bolts from Step 6.
-66-
#1
Front
#3
#2
Figure 114. Shim procedure diagram B.
Model G0833P (Mfd. Since 06/17)
11. Tighten one table mounting bolt a small
amount and then repeat with the others,
tightening each down the same amount.
Continue this process with all the bolts, tightening them a little each time until they are all
secure.
12. Now recheck blade to miter slot at 0° and 45°
by repeating Steps 2-5.
—If distance of A and B are equal, continue
to Step 13.
—If distances
Steps 9–12.
are
not
equal,
Checking Alignment
The blade guard spreader and riving knife must
be aligned with the blade when installed. If the
spreader/riving knife is not aligned with the blade,
then the workpiece will before forced sideways
during the cut, which will increase the risk of kickback.
repeat
13. Once miter slot is adjusted to blade, recheck
all measurements and be sure table mounting bolts are secure.
Spreader or Riving
Knife Alignment
Note: If you remove the table in the future,
note the shim placement and reassemble
them exactly how they came apart.
Qty
Tools Needed
Straightedge....................................................... 1
To check spreader/riving knife alignment:
1. DISCONNECT MACHINE FROM POWER!
2. Raise saw blade to maximum height so you
have easy working access.
3. Place straightedge against side of blade and
spreader/riving knife at top and bottom, as
shown in Figure 115. Spreader/riving knife
should be parallel with blade along its length
at both positions, and in "Alignment Zone," as
shown in Figure 116.
Top Alignment
Bottom Alignment
Figure 115. Checking top and bottom riving knife
parallelism with blade.
Model G0833P (Mfd. Since 06/17)
-67-
Alignment
Zone
Spreader or
Riving Knife
3. Loosen (2) cap screws on mounting block, then
adjust either top or bottom control set screws
or side control set screws (see Figure 117) to
move it the needed direction.
Blade
Set Screw
(1 of 4)
Figure 116. Spreader/riving knife alignment
zone.
—If spreader/riving knife is not parallel
with blade and inside alignment zone,
then it needs to be adjusted. Proceed to
Adjusting Alignment instructions.
Center
Screw
Blade
—If spreader/riving knife does not lay evenly,
proceed to Adjusting Bent Spreader/
Riving Knife on Page 69.
Tool Needed
Qty
Hex Wrench 2.5mm............................................ 1
1. DISCONNECT MACHINE FROM POWER!
2. Remove table insert.
Bottom Control
Figure 117. Set screws for adjusting spreader/
riving knife position.
Adjusting Alignment
To adjust spreader/riving knife position:
Side
Control
Misaligned
Splitter or
Riving Knife
4. Remove spreader/riving knife and place it on
flat surface and check to see if spreader/riving knife lays evenly along its length.
Adjustment Block
Top Control
Side
Control
Alignment
Zone
—If spreader/riving knife is not parallel with
the blade at either the top or bottom, it may
be bent.
The spreader/riving knife mounting position can
be adjusted into alignment with the blade using
the set screws on the spreader/riving knife mounting block.
Cap
Cap
Screws
Screws
Top and Bottom Control: To move the top
of the spreader/riving knife right or left (and
the bottom of the spreader/riving knife in the
opposite direction), adjust the top and bottom
pair of set screws on the mounting block an
equal amount in the opposite direction.
Side Control: To move the front of the
spreader/riving knife left or right (and the rear
of the spreader/riving knife in the opposite
direction), adjust each pair of side control
set screws an equal amount in the opposite
direction.
Note: To adjust how tightly the mounting
block holds the spreader/riving knife, adjust
the center screw.
-68-
Model G0833P (Mfd. Since 06/17)
4. Re-install table insert.
5. Follow Checking Alignment, Steps 1–3.
—If spreader/riving knife is in alignment
zone, no additional steps are necessary.
—If spreader/riving knife is still not in alignment zone, continue adjusting set screws
on mounting block as necessary to correctly position spreader/riving knife.
Fence Adjustments
There are four main adjustments for the fence:
height off the table, squareness, parallelism with
the miter slot, and clamping pressure. These
adjustments are interconnected and some repetition may be needed when adjusting.
6. Tighten (2) cap screws on mounting block to
secure spreader/riving knife adjustment.
Tools Needed
Qty
Hex Wrench 6mm............................................... 1
Square................................................................ 1
Felt-Tipped Marker............................................. 1
Adjusting Bent Spreader/Riving Knife
Height and Square
1. DISCONNECT MACHINE FROM POWER!
2. Bend spreader or riving knife by hand while
installed, then follow Steps 1–3 in Checking
Alignment on Page 67 to determine if it is parallel with blade and inside "Alignment Zone"
(refer to Figure 115 Checking Alignment on
Page 67).
The fence should be adjusted high enough off the
table so that it does not drag across the surface or
allow wood chips to get caught between the fence
and table. Also, the fence face must be square to
the table in order to produce accurate cuts.
To check/adjust fence height and squareness
to table:
—­If this doesn't work, remove it to straighten.
1. DISCONNECT MACHINE FROM POWER!
—If you cannot straighten it properly,
replace it.
2. Remove fence from saw and place it on a flat
surface.
3. Unscrew front lock nuts and adjustment
screws shown in Figure 118 until they are
barely threaded into fence flange.
4. Back out rear set screws until they are just
threaded into fence flange (see Figure 118).
Rear Set Screws
Front Lock Nuts
and Adjustment Screws
Figure 118. Location of screws used to adjust
fence parallelism and clamping pressure.
Model G0833P (Mfd. Since 06/17)
-69-
5. Install fence onto table, then loosen fence
knobs (see Figure 119), pull fence up from
center, and tighten each knob.
6. Loosen top lock nuts on fence flange and lock
nut on rear rail foot, shown in Figure 119.
Parallelism & Clamping Pressure
Set screws on the rear side of the fence flange
position the fence parallel to the blade and adjust
the clamping pressure to hold fence securely.
Before starting this procedure, make sure the
blade is parallel with the miter slot.
To adjust fence parallelism and clamping
pressure:
Top
Adjustment Screws
Lock Nut
1. DISCONNECT MACHINE FROM POWER!
Knob
(1 of 3)
Rear Rail
Foot
Fence Flange
Figure 119. Fence components used to adjust
fence height and squareness to table.
7. Turn top adjustment screws and rear foot
screw so there is approximately 1⁄16" clearance between bottom of fence and table,
front-to-back and side-to-side, then tighten
lock nuts.
8. Place square on table and against face of
fence, as shown in Figure 120, to check if
fence is square to table.
—If fence is square to table, proceed to
Parallelism & Clamping Pressure.
2. Lock fence, tap front side with your fist, and
check to see if it moved sideways over table.
—If fence did not move, proceed to Step 5.
—If fence moved, remove it from table and
proceed to Step 3.
3. Turn each rear set screw (see Figure 118 on
Page 69) in 1⁄6th of a turn.
4. Re-install fence and repeat Step 2.
5. Slide fence up against right-hand edge of
miter slot, as shown in Figure 121, and lock
it in place.
Miter
Slots
Fence
Face
Flush
Side View (Good)
A
—If fence is not square to the table, proceed
to Step 9.
Overlap
Side View (Bad)
90° Square
Fence
Table
Top View
B
Figure 121. Example of aligning fence to miter
slot.
Figure 120. Checking if fence is square to table.
9. Loosen top lock nuts and adjust top screws
(see Figure 119) to make fence face 90° to
table, then tighten lock nuts.
-70-
Model G0833P (Mfd. Since 06/17)
6. Examine how fence lines up with miter slot
along its length.
—If fence and miter slot are flush from front
to rear, as shown in Figure 121A, proceed
to Step 8.
—If rear of fence overlaps miter slot, as
shown in Figure 121B, fence is misaligned. Proceed to Step 7.
7. Remove fence, then alternately loosen
and tighten rear fence set screws in equal
amounts to adjust rear of fence until it is parallel with miter slot.
8. Loosen both front lock nuts (see Figure 118
on Page 69). Tighten adjustment screws so
they just touch fence tube, back off screws 1⁄2
turn, then tighten lock nuts.
Optional Offset Fence Adjustment
Some woodworkers prefer to offset the rear of
the fence 1/64" from the blade, as shown in Figure
122, to help prevent the workpiece from binding
and burning.
The argument is that this offset adjustment reduces the chance of kickback by alleviating potential
binding that may occur between the backside of
the blade and fence. The tradeoff is slightly less
accurate cuts.
X = Your Measurement
Blade
X" + 1/64"
X"
Extra Space
to Prevent Binding
(Optional)
Figure 122. Adjusting fence with a 1⁄64" offset.
To offset fence:
1. DISCONNECT MACHINE FROM POWER!
2. With a felt tip pen, mark one saw tooth and
rotate blade so this tooth is positioned at back
of table insert.
3. Place fence on table, and clamp fence to
table.
4. Measure distance between tooth and fence
face, as shown in Figure 122.
5. Remove fence, and adjust rear set screws as
previously discussed to achieve an offset of
1
/64" between marked tooth and fence face.
6. Re-install fence and measure distance again
between marked tooth and fence face. The
rear measurement should be 1/64" greater
than previously measured in Step 4.
Model G0833P (Mfd. Since 06/17)
-71-
Fence Scale
Calibration
Table/Dado Insert
Adjustment
The fence scale indicator window, shown in
Figure 123, can be calibrated with the fence
scale if you notice that your cuts do not accurately
match what is shown on the fence scale.
The table/dado insert must sit perfectly flush with
the table to provide a smooth, continuous surface
for the workpiece to slide over. The insert is held
in place by a magnet and sits on top of four adjustment screws (see Figure 124).
Screws
The insert should be checked and adjusted any
time it is removed and replaced, after prolonged
use, or any time you notice the workpiece or fence
does not slide smoothly over the insert.
Indicator Window
Figure 123. Fence indicator window.
The indicator adjusts by loosening the two mounting screws and sliding it in the desired direction.
Figure 124. Location of table/dado insert holes
with adjustment screws.
Qty
Tools Needed
Hex Wrench 3mm............................................... 1
Scrap Piece of Wood......................................... 1
Tape Measure..................................................... 1
Tools Needed
Qty
Hex Wrench 3mm............................................... 1
Straightedge....................................................... 1
To calibrate fence scale indicator windows:
To check and adjust insert:
1. Position and lock fence at 13", as indicated
by scale, then cut your scrap piece of wood.
1. DISCONNECT MACHINE FROM POWER!
2. Reposition and lock fence at 12", as indicated
by scale.
2. Place straightedge across insert and check
to make sure insert is flush with table at front
and back of throat.
3. Flip your scrap piece of wood over, placing
side that was cut in Step 2 against fence, and
cut your scrap piece of wood.
—If insert is flush with table, no adjustments
are necessary.
4. Measure width of freshly cut workpiece with
tape measure. Workpiece width should be
exactly 12". If it is not, then adjust indicator
window to match the width of workpiece.
-72-
—If insert is not flush with table, proceed to
Step 3.
3. Insert hex wrench through holes shown in
Figure 124 and either loosen screws to raise
insert, or tighten screws to lower it. Repeat
Steps 2–3 until insert is perfectly flush with
surface of table.
Model G0833P (Mfd. Since 06/17)
Miter Gauge
Adjustments
4. Place square evenly against face of miter
gauge and blade, as shown in Figure 126.
Square
Blade
The miter gauge can be adjusted so it is perpendicular to the blade and snug in the T-slot.
Tools Needed
Qty
90° Square......................................................... 1
45° Square......................................................... 1
Hex Wrench 2mm............................................... 1
Hex Wrench 2.5mm............................................ 1
Hex Wrench 4mm............................................... 1
Checking/Setting 90° Stops
1. DISCONNECT MACHINE FROM POWER!
2. Slide miter gauge into T-slot on table.
3. Loosen miter gauge lock knob, pull out positive stop knob, then pivot miter gauge body
to 90° so stop knob springs into position (see
Figure 125).
Set Screws
Positive Stop
Knob
Miter Gauge
Figure 126. Checking 90° stop on miter gauge.
—If square touches miter body and body of
blade (not the teeth) evenly at same time,
then it is square to blade and 90° stop is
set correctly. No further adjustments are
necessary.
—If square does not touch miter body and
blade body evenly at same time, then proceed to Step 5.
5. Loosen button head cap screws on positive
stop knob block (see Figure 127), adjust
miter body until it is flush with square, then
tighten screws.
Positive Stop
Knob Block
Lock Knob
Indicator
Screw
Figure 125. Set screws for adjusting miter bar in
miter slot.
Button Head Cap Screws
Figure 127. Screws for adjusting miter body.
6. Loosen indicator screw on top of miter bar,
adjust pointer to 0°, then tighten screw.
Adjusting Miter Bar Tightness
The miter bar can be adjusted so it fits more tightly
in the miter slot. To adjust the miter bar tightness,
adjust the set screws shown in Figure 125 as
needed. Bar should slide with little resistance.
Model G0833P (Mfd. Since 06/17)
-73-
Belt Tension &
Replacement
The drive belt stretches slightly as the saw is
used. Most of the belt stretching will happen during the first 16 hours of use, but it may continue
through continued use. If you notice that the belt
is slipping, it will need to be tensioned. If the belt is
cracked, frayed, or shows other signs of excessive
wear, it will need to be replaced.
Tool Needed
Qty
Hex Wrench 6mm............................................... 1
Tensioning Belt
1. DISCONNECT MACHINE FROM POWER!
2. Raise blade completely, then open the motor
door.
3. Loosen cap screw on motor shown in Figure
128, and pivot motor up and down to make
sure that it is movable.
Belt
Pulley
1
⁄4"
Pulley
Deflection
Figure 129. Checking belt tension.
—If there is more than 1⁄4" deflection when
belt is pushed with moderate pressure,
loosen cap screw, push motor downward,
then tighten cap screw.
6. Close motor door.
Replacing Belt
1. DISCONNECT MACHINE FROM POWER!
2. Raise blade completely, then open motor
door.
3. Loosen cap screw that secures motor (see
Figure 128) and lift motor fully to remove tension on belt. Tighten cap screw to hold motor
in this position, then roll belt off of the arbor
and motor pulleys.
Cap Screw
Figure 128. Location of cap screw for adjusting
belt tension.
4. Press down on motor with one hand to keep
belt tension tight and tighten cap screw.
4. Install new belt onto pulleys, loosen cap
screw, then lower motor.
5. Press down on motor with one hand to keep
belt tension tight and tighten cap screw.
6. Follow Step 5 in the Tensioning Belt subsection on this page to check V-belt tension.
7. Close motor door.
5. Press belt in center to check belt tension.
The belt is correctly tensioned when there
is approximately 1⁄4" deflection when it is
pushed with moderate pressure, as shown in
Figure 129.
-74-
Model G0833P (Mfd. Since 06/17)
machine
SECTION 9: WIRING
These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one
stated in this manual, and study this section carefully.
If there are differences between your machine and what is shown in this section, call Technical Support at
(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated
wiring diagram may be available. Note: Please gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring Safety Instructions
SHOCK HAZARD. Working on wiring that is connected to a power source is extremely dangerous.
Touching electrified parts will result in personal
injury including but not limited to severe burns,
electrocution, or death. Disconnect the power
from the machine before servicing electrical components!
MODIFICATIONS. Modifying the wiring beyond
what is shown in the diagram may lead to unpredictable results, including serious injury or fire.
This includes the installation of unapproved aftermarket parts.
WIRE CONNECTIONS. All connections must
be tight to prevent wires from loosening during
machine operation. Double-check all wires disconnected or connected during any wiring task to
ensure tight connections.
CIRCUIT REQUIREMENTS. You MUST follow
the requirements at the beginning of this manual
when connecting your machine to a power source.
WIRE/COMPONENT DAMAGE. Damaged wires
or components increase the risk of serious personal injury, fire, or machine damage. If you notice
that any wires or components are damaged while
performing a wiring task, replace those wires or
components.
MOTOR WIRING. The motor wiring shown in
these diagrams is current at the time of printing
but may not match your machine. If you find this
to be the case, use the wiring diagram inside the
motor junction box.
CAPACITORS/INVERTERS. Some capacitors
and power inverters store an electrical charge for
up to 10 minutes after being disconnected from
the power source. To reduce the risk of being
shocked, wait at least this long before working on
capacitors.
EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information
included in this section, contact our Technical
Support at (570) 546-9663.
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
color at www.grizzly.com.
Model G0833P (Mfd. Since 06/17)
-75-
Wiring Diagram
Neutral
Line
230 VAC
6-20 PLUG
Load
Hot
Line
Ground
Ground
Rewired for 115V
Line
KEDU HY56
20A 230V
35A 120V
Load
Hot
Circuit Breaker
KUOYUH HY88
20A 110V
115 VAC
5-20 Plug
(As Recommended)
Load
ON/OFF
SWITCH
Circuit Breaker
KUOYUH
10A 125V/250V
SWITCH BOX
GND
Hot
GND
Rewired for 115V
Run
Capacitor
40MFD
450VAC
Start
Capacitor
200–240MFD
250VAC
115V/230V
MOTOR
Motor Rewired
for 115V
Motor Prewired
for 230V
GND
GND
Rewired for 115V
-76-
READ ELECTRICAL SAFETY
ON PAGE 75!
Model G0833P (Mfd. Since 06/17)
Electrical Components
Capacitors
Circuit
Breaker
ON/OFF
Switch
Figure 130. Motor capacitors.
Figure 132. Switch box components.
Motor Junction
Box
Figure 131. Motor junction box.
Model G0833P (Mfd. Since 06/17)
READ ELECTRICAL SAFETY
ON PAGE 75!
-77-
SECTION 10: PARTS
We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown
are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability.
Body
1
2 3 4
5
6
7
31
8
4
3 2
1
19 21 20 23
27 28 29
13 25
28
14
15
16
9
11
32
22
13
36
18
23
24
10 12 26
30
17
34
33
35
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
EXTENSION WING
CAP SCREW M10-1.5 X 25
LOCK WASHER 10MM
FLAT WASHER 10MM
TABLE INSERT (STANDARD)
FLAT HD CAP SCR M5-.8 X 10
TABLE INSERT MAGNET
MAIN TABLE
MOTOR COVER
INT TOOTH WASHER 6MM
KNOB M6-1
RIVETED NUT M6-1 X 15
HEX BOLT M8-1.25 X 25
FLAT WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 25
CABINET
ACCESS COVER
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
HEX NUT M5-.8
FLAT WASHER 5MM
LOCK WASHER 5MM
BUTTON HD CAP SCR M5-.8 X 12
LEADSCREW BRACKET
BUTTON HD CAP SCR M5-.8 X 16
LOCK NUT M8-1.25
TILT SCALE
LOCK NUT M3-.5
UPPER AND LOWER HINGE
FLAT HD CAP SCR M3-.5 X 12
STRAIN RELIEF TYPE-3 M18-1.5
TABLE INSERT (DADO)
SET SCREW M5-.8 X 8
FLAT WASHER 6MM
DUST PORT 4" X 1-1/2"
BUTTON HD CAP SCR M6-1 X 12
LOCK NUT M8-1.25
-78-
P0833P001
P0833P002
P0833P003
P0833P004
P0833P005
P0833P006
P0833P007
P0833P008
P0833P009
P0833P010
P0833P011
P0833P012
P0833P013
P0833P014
P0833P015
P0833P016
P0833P017
P0833P018
P0833P019
P0833P020
P0833P021
P0833P022
P0833P023
P0833P024
P0833P025
P0833P026
P0833P027
P0833P028
P0833P029
P0833P030
P0833P031
P0833P032
P0833P033
P0833P034
P0833P035
P0833P036
BUY PARTS
ONLINE
AT GRIZZLY.COM!
Model
G0833P
(Mfd. Since
Scan QR code to visit our Parts Store.
06/17)
Trunnion
106-1
106-2
106-4
106-6
106-8
106-9
106-10
103
106-7
106-5
106-3
106-11
118
117
108
109
104
105 106
120
110
108
112
107 109
113
121
127 128 129
130
101 102
198
114
116
108 109 124
107
134
111
115
103
199
200
141
122
119 120
146
142
139
108
201
125
104
143
144
131
104
115
123
126
122 123
164
173
103
155 157
159 160
154 156
158
115
108
147
136 137 138
201
135
133
104
143
132
153
163
120 165
146
150
162
171 148 119
149
166
161
167
140
204
135 108 139
152
151
205
115
174 176 175
145
168
177
179
123
175
180
192
191
190
189
196
135
108
197
201
188
187
194
102
202
174
203
180
115
182 181 183
202
185
193
172 120
195
178
170
120
119
169
184
187
186
188
186
Model G0833P (Mfd. Since 06/17)
-79-
Trunnion Parts List
REF
PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
104
105
106
106-1
106-2
106-3
106-4
106-5
106-6
106-7
106-8
106-9
106-10
106-11
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
P0833P101
P0833P102
P0833P103
P0833P104
P0833P105
P0833P106
P0833P106-1
P0833P106-2
P0833P106-3
P0833P106-4
P0833P106-5
P0833P106-6
P0833P106-7
P0833P106-8
P0833P106-9
P0833P106-10
P0833P106-11
P0833P107
P0833P108
P0833P109
P0833P110
P0833P111
P0833P112
P0833P113
P0833P114
P0833P115
P0833P116
P0833P117
P0833P118
P0833P119
P0833P120
P0833P121
P0833P122
P0833P123
P0833P124
P0833P125
P0833P126
P0833P127
P0833P128
P0833P129
P0833P130
P0833P131
P0833P132
P0833P133
P0833P134
P0833P135
P0833P136
P0833P137
P0833P138
P0833P139
P0833P140
P0833P141
P0833P142
P0833P143
P0833P144
P0833P145
P0833P146
P0833P147
LOCK NUT M16-2
FLAT WASHER 16MM
CAP SCREW M8-1.25 X 20
LOCK WASHER 8MM
FLAT WASHER 8MM
MOTOR 2HP 110V/220V 1-PH
MOTOR FAN COVER
MOTOR FAN
START CAPACITOR COVER
S CAPACITOR 200-240M 250V 1-1/2 X 2-3/4
RUN CAPACITOR COVER
R CAPACITOR 40M 450V 2 X 4
MOTOR JUNCTION BOX
CONTACT PLATE
CENTRIFUGAL SWITCH
BALL BEARING 6203ZZ (FRONT)
BALL BEARING 6204ZZ (REAR)
CAP SCREW M6-1 X 16
LOCK WASHER 6MM
FLAT WASHER 6MM
ARBOR PULLEY
POLY V-BELT 150PJ6
BUSHING
BALL BEARING 6202-2RS
KEY 6 X 6 X 20
SET SCREW M6-1 X 8
MOTOR PULLEY
HEX BOLT M6-1 X 16
LOCK NUT M5-.8
LOCK WASHER 5MM
FLAT WASHER 5MM
ARBOR LOCK
HEX BOLT M8-1.25 X 40
HEX NUT M8-1.25
HEIGHT LIMIT BLOCK
LOCK NUT M8-1.25
MOTOR MOUNT
ARBOR BUSHING
BALL BEARING 6202-2RS
KEY 5 X 5 X 15
ARBOR
FLAT WASHER 8MM
FRONT TRUNNION
HEX BOLT M8-1.25 X 45
LIMIT BLOCK
FLAT WASHER 6MM
FLAT HD CAP SCR M10-1.5 X 40
SPACER
SPACER (NYLON)
CAP SCREW M6-1 X 35
SHAFT BRACKET
MAIN TRUNNION
MOTOR SHAFT
FLAT WASHER 8MM
REAR TRUNNION
ADJUSTMENT SCREW
NYLON GASKET
SPREADER BRACKET
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
SPRING BRACKET
FLANGE RING
FLAT HD CAP SCR M5-.8 X 50
SAW BLADE 10" X 40T
ARBOR FLANGE
ARBOR NUT M16-2
KNURLED KNOB
SPREADER ADJUSTMENT BLOCK
COMPRESSION SPRING
SPACER
LOCKING PIN 6 X 26
SPREADER CLAMPING PLATE
CAP SCREW M6-1 X 25
BUTTON HD CAP SCR M6-1 X 20
CONNECTING PLATE
LOCK NUT M6-1
BUTTON HD CAP SCR M5-.8 X 16
HEX NUT M5-.8
EXTENSION SPRING
SHOULDER SCREW M6-1 X 16, 6 X 12
DUST COLLECTOR CASE
CAP SCREW M5-.8 X 12
POINTER
BUTTON HD CAP SCR M5-.8 X 12
BUTTON HD CAP SCR M4-.7 X 8
MOTOR LOCATING SHAFT
STOP COLLAR
INT RETAINING RING 24MM
TILT LEADSCREW NUT
TILT LEADSCREW BASE
ROLL PIN 4 X 16
TILT LEADSCREW
ROLL PIN 4 X 20
FLAT WASHER 12MM
BEARING WASHER
EXT RETAINING RING 12MM
BEVELED BUSHING
FLAT WASHER 12MM
HANDWHEEL TYPE -7 160D X 11.5B-K X M10-1.5
HANDWHEEL LOCK KNOB M8-1.25 5-LOBE
HANDWHEEL HANDLE 90L, M10-1.5 X 12
LOCK NUT M12-1.75
FLAT WASHER 12MM
COLLAR
ELEVATION SHAFT
POINTER BASE
HANDWHEEL BUSHING
COMPRESSION SPRING
ELEVATION SHAFT SPACER
CAP SCREW M6-1 X 20
STRAIN RELIEF TYPE-1 3/8"
CAP SCREW M5-.8 X 30
CAP SCREW M5-.8 X 20
SET SCREW M6-1 X 20
HOSE CLAMP 3-1/4"
CLEAR HOSE 26" X 3"
HEX NUT M10-1.5
ARBOR FLANGE (DADO)
-80-
P0833P148
P0833P149
P0833P150
P0833P151
P0833P152
P0833P153
P0833P154
P0833P155
P0833P156
P0833P157
P0833P158
P0833P159
P0833P160
P0833P161
P0833P162
P0833P163
P0833P164
P0833P165
P0833P166
P0833P167
P0833P168
P0833P169
P0833P170
P0833P171
P0833P172
P0833P173
P0833P174
P0833P175
P0833P176
P0833P177
P0833P178
P0833P179
P0833P180
P0833P181
P0833P182
P0833P183
P0833P184
P0833P185
P0833P186
P0833P187
P0833P188
P0833P189
P0833P190
P0833P191
P0833P192
P0833P193
P0833P194
P0833P195
P0833P196
P0833P197
P0833P198
P0833P199
P0833P200
P0833P201
P0833P202
P0833P203
P0833P204
P0833P205
Model G0833P (Mfd. Since 06/17)
Power Switch
226
227
229
228
231
232
223
229
222
233
224
225
224X
(for 115V conversion)
235
236
221
222-1
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
221
222
222-1
223
224
224X
225
226
TAP SCREW M3.5 X 19
S/S SWITCH W/STOP PADDLE KEDU HY56
PADDLE SWITCH LOCKOUT PIN
SWITCH BOX
CIRCUIT BREAKER KUOYUH 88 10A 230V
CIRCUIT BREAKER KUOYUH 88 20A 115V
CIRCUIT BREAKER NUT M10-1.5
PHLP HD SCR M5-.8 X 8
227
228
229
231
232
233
235
236
LOCK WASHER 5MM
FLAT WASHER 5MM
CLAMP-ON TERMINAL RING
SWITCH BRACKET
TAP SCREW M3.5 X 10
STRAIN RELIEF TYPE-3 M18-1.5
POWER CORD 14G 3W 72" 6-20P
MOTOR CORD 14G 3W 32"
P0833P221
P0833P222
P0833P222-1
P0833P223
P0833P224
P0833P224X
P0833P225
P0833P226
Model G0833P (Mfd. Since 06/17)
P0833P227
P0833P228
P0833P229
P0833P231
P0833P232
P0833P233
P0833P235
P0833P236
-81-
Blade Guard
301 302 303
304
306
325
312
311
335
309
307
308
324
323
305
312A
322
313
326
302
318
314
315
317
316
319
320
321
312
303
311
331
337
336
332
333
339
335
338
334
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
301
302
303
304
305
306
307
308
309
311
312
312A
313
314
315
316
317
318
FLAT HD CAP SCR M4-.7 X 10
GUARD SUPPORT (FRONT)
GUARD SUPPORT (REAR)
FLANGE NUT M4-.7
DUST CHUTE
LEFT GUARD
TAP SCREW M3.5 X 16
SPRING CLAMP
BLADE GUARD DUST PORT
BUTTON HD CAP SCR M4-.7 X 10
SIDE GUARD
COMPLETE BLADE GUARD ASSY
TORSION SPRING
PAWL SHAFT
SPREADER
ROLL PIN 4 X 16
PAWL RELEASE HOOK
RIVET 4 X 8
319
320
321
322
323
324
325
326
331
332
333
334
335
336
337
338
339
ANTI-KICKBACK PAWL
SPACER
BUTTON HD CAP SCR M4-.7 X 6
SHOULDER SCREW M5-.8 X 10, 11 X 35
SHOULDER SCREW M5-.8 X 10, 11 X 20
RIGHT GUARD
TAP SCREW M3 X 10
RIVING KNIFE
HOSE SUPPORT ARM
HEX NUT M6-1
FLAT WASHER 6MM
WING NUT M6-1
HOSE CONNECTOR 1-1/2"
DUST HOSE 94" X 1-1/2"
PUSH STICK
HEX WRENCH SET 2.5-8MM 6-PC
WRENCH 13 X 27MM OPEN-ENDS
-82-
P0833P301
P0833P302
P0833P303
P0833P304
P0833P305
P0833P306
P0833P307
P0833P308
P0833P309
P0833P311
P0833P312
P0833P312A
P0833P313
P0833P314
P0833P315
P0833P316
P0833P317
P0833P318
P0833P319
P0833P320
P0833P321
P0833P322
P0833P323
P0833P324
P0833P325
P0833P326
P0833P331
P0833P332
P0833P333
P0833P334
P0833P335
P0833P336
P0833P337
P0833P338
P0833P339
Model G0833P (Mfd. Since 06/17)
Miter Guage
418
419
417
403
408
404
402
412
407
405
416
415
414
409
411
410
406
401
413
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
401
402
403
404
405
406
407
408
409
410
GUIDE BAR
ANGLE SCALE
RIVET 2.5 X 8 BLIND, STEEL
SET SCREW M8-1.25 X 6
MITER RING
FLAT HD CAP SCR M5-.8 X 8
MITER BODY PIVOT PIN
MITER GAUGE BODY
MITER STOP PIN KNOB
PIN BLOCK
411
412
413
414
415
416
417
418
419
COMPRESSION SPRING
MITER STOP PIN
BUTTON HD CAP SCR M4-.7 X 10
MITER GAUGE POINTER
FLAT WASHER 4MM
LOCK WASHER 4MM
BUTTON HD CAP SCR M4-.7 X 6
LOCKING HANDLE M8-1.25 X 24
FLAT WASHER 8MM
P0833P401
P0833P402
P0833P403
P0833P404
P0833P405
P0833P406
P0833P407
P0833P408
P0833P409
P0833P410
Model G0833P (Mfd. Since 06/17)
P0833P411
P0833P412
P0833P413
P0833P414
P0833P415
P0833P416
P0833P417
P0833P418
P0833P419
-83-
Fence
523
519
521
524
525
522
520
502
513
514
515
503
502
512
507
505
510
511
509
504
508
506
501
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
501
502
503
504
505
506
507
508
509
510
511
GLIDE PAD
KNURLED NUT M12-1.75
SET SCREW M12-1.75 X 16 BRASS
SET SCREW M12-1.75 X 10
HEX BOLT M6-1 X 40
CAM LOCK PLATE
LOCK NUT M6-1
HEX BOLT M10-1.5 X 45
FENCE LOCK CAM LEVER
MAGNET
BALL KNOB M10-1.5
512
513
514
515
519
520
521
522
523
524
525
LOCK NUT M10-1.5
BUTTON HD CAP SCR M5-.8 X 8
FLAT WASHER 5MM
FENCE SCALE WINDOW
FENCE BASE END CAP 50 X 50MM
SET SCREW M12-1.75 X 30
FENCE FACE
FENCE BASE
FENCE T-BOLT M6-1 X 30
FLAT WASHER 6MM
KNOB 5-LOBE M6-1 X 30
-84-
P0833P501
P0833P502
P0833P503
P0833P504
P0833P505
P0833P506
P0833P507
P0833P508
P0833P509
P0833P510
P0833P511
P0833P512
P0833P513
P0833P514
P0833P515
P0833P519
P0833P520
P0833P521
P0833P522
P0833P523
P0833P524
P0833P525
Model G0833P (Mfd. Since 06/17)
Fence Rails
610
611
610
609
609
616
609
613
614
615
609
611
616
612
609
610
611
619
618
617
601
605
604
606
607
608
602
603
601
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
601
602
603
604
605
606
607
608
609
610
GUIDE-TUBE END CAP 50 X 40MM
FENCE GUIDE TUBE
FRONT FENCE RAIL
FENCE SCALE LABEL
FLAT WASHER 6MM
LOCK WASHER 6MM
CAP SCREW M6-1 X 16
FLAT HD CAP SCR M8-1.25 X 35
FLAT WASHER 8MM
LOCK WASHER 8MM
611
612
613
614
615
616
617
618
619
HEX NUT M8-1.25
REAR FENCE RAIL
CAP SCREW M10-1.5 X 25
LOCK WASHER 10MM
FLAT WASHER 10MM
CAP SCREW M8-1.25 X 35
CAP SCREW M5-.8 X 14
LOCK WASHER 5MM
FLAT WASHER 5MM
P0833P601
P0833P602
P0833P603
P0833P604
P0833P605
P0833P606
P0833P607
P0833P608
P0833P609
P0833P610
Model G0833P (Mfd. Since 06/17)
P0833P611
P0833P612
P0833P613
P0833P614
P0833P615
P0833P616
P0833P617
P0833P618
P0833P619
-85-
Scale= 1:1
WARNING!
G0833P Machine
LabelsWARNING!
B • (unless
otherwise noted)
The Model G0833P
spreader/riving knife is
If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.
INJURY/SHOCK
0.1" thick. Follow these
HAZARD!to ensure the
requirements
power
Disconnect
spreader/riving
knife works
adjustments,
before
safely:
or
maintenance,
BLADE REQUIREMENTS
service.
Standard Blades
Disconnect power
before changing
blades or blade
guard and riving
knife.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine
INJURY HAZARD!
(06/13/17)
Do not open door
while machine is
connected to power
or blade is in motion.
• Labels MUST be made of
Rotating
blade adjustment
handwheels into
chemical-resistant
material
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width: 13/16"
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
AMPUTATION
If blade guard is
Removing blade
HAZARD!
• Always
Scale=
removed for a
keep1:1 guard increases
special cut, some
risk of injury—it
fingers
and otherwise
INJURY/SHOCK
(unless
noted)
other safeguard
hands away from MUST be installed
HAZARD!
when
moving
blade.
powerbe used.
Disconnect
• Labels
MUST
bepossible.
made
ofMUST
before adjustments,
chemical-resistantmaintenance,
materialor
service.
G0833P Machine Labels B G0833P Machine Labels B
706
705
(06/13/17)
Disconnect power
before changing
blades or blade
INJURY HAZARD!
guard and riving
Do
not open door
knife.
while machine is
connected to power
or blade is in motion.
The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
• Scale= 1:1
spreader/riving
knife works
WARNING!
(unless
otherwise
safely:
EYE/LUNG INJURY
Industrial Rip Fence
G0715P Machine Labels 2
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width: 13/16"
WARNING!
noted)
To reduce risk of death
BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width 13/16"
Rotating blade adjustment handwheels into
with excessive force could
result151
in Caorloss
of blade parallelism with miter
PANTONE
RAL 2005
slot, impaired stop-collar accuracy, and
PANTONE 109 C
damage to internal components. This type of
AMPUTATION
PANTONE
3005is
C or
RALcovered
5005
damage
not
by warranty!
Removing blade
HAZARD!
PANTONE
485 Cpositions
or RAL 3001
stopping
COLOR CODES
WARNING!
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
INJURY HAZARD
PANTONE 109 C
NOTICE
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
709Labels B
G0833P Machine
(06/13/17)
703
requirements to ensure the
WARNING
PANTONE
151 C or
RALworks
2005
spreader/riving
knife
removed for a
guard increases
before changing
Always keepknife works
spreader/riving
safely:
risk of injury—it
special cut, some blades or blade
fingers and
safely:
PANTONE 109 C
CAUTION
guard and
riving
hands away from MUST be installed other safeguard
BLADE REQUIREMENTS
when possible.
MUST be used.
knife.
BLADE
REQUIREMENTS
moving
blade.
Standard 3005
Blades
NOTICE
PANTONE
C or RAL 5005
Standard Blades
• Diameter: 10"
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Max. Body Thickness: 0.094"
COPYRIGHT © GRIZZLY INDUSTRIAL, INC. • Min. Kerf Thickness: 0.102"
• Min. Kerf Thickness: 0.102"
• MustTHIS
be aligned
with
FOR
GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE
ARTWORK
• Must be aligned with
spreader
or riving
knife. If
Grizzly 1:1
will not accept labels changed
without
approval.
WITHOUT
WRITTEN
• Scale=
spreader or
riving knife.APPROVAL!
Dado Blades
artwork changes are required,
contact
usinto
immediately
at manuals@grizzly.com.
(unless
otherwise
noted)
handwheels
Dado Blades Rotating blade adjustment
• Dado blades under 10"
• Dado blades stopping
under 10" positions with excessive force could
diameter not compatible
• Labels
be made of
in a loss of blade
parallelismMUST
with miter
diameter notresult
compatible
COLOR CODES
with riving knife.
slot, impaired stop-collar
accuracy, and
with riving knife.
chemical-resistant
material • Max Width: 13/16"
damage to internal components. This type of
• Max Width: 13/16"
DANGER
PANTONE 485 C or RAL 3001
CAUTION
NOTICE
PANTONE 109 C
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
PANTONE 109 C
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
712
BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
Dado Blades
• Dado blades under 10"
diameter not compatible
with riving knife.
• Max Width: 13/16"
714
715
grizzly.com
COLOR CODES
G0833P
DANGER
PANTONE 485 C or RAL 3001
WARNING
PANTONE 151 C or RAL 2005
CAUTION
PANTONE 109 C
NOTICE
PANTONE 3005 C or RAL 5005
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
USE
FOR GRIZZLY MACHINES ONLY! DO
NOTPANTONE
REPRODUCEDS
OR9-9C
CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
716
***
PANTONE 485 C or RAL 3001
The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:
***
COLOR CODES
DANGER
Disconnect power
before changing
blades or blade
guard and riving
knife.
(06/13/17)
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
RAL 9010
PANTONE 568C
PANTONE 151 C or RAL 2005
PANTONE 568C
PANTONE 711C or RAL 3020
PANTONE 7406C or RAL 1003
COLOR CODE
WARNING
GRIZZLY GRAY
GRIZZLY GREEN
• 1:1 Scale (Labels are
actual size)
• Labels must be made of
chemical-resistant material
GRIZZLY LOGO RED
GRIZZLY LOGO YELLOW
If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
GRIZZLY GREEN
COLOR CODES
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
18. Non-through cuts (i.e. dadoes, rabbets, moulding cuts) and
resawing cuts present specific dangers; refer to the manual.
19. Do not wear loose clothing, gloves, jewelry, or other items that
can get entangled. Tie back long hair and roll up sleeves.
20. Do not expose to rain or operate in a wet environment.
21. Prevent unauthorized use by children or untrained users;
restrict access or disable machine when unattended.
(06/19/17)
made with either device, some other safeguard MUST be used.
use blades meeting size/speed requirements for this saw.
Dado Blades6.7. Only
Ensure spreader/riving knife and fence are properly adjusted.
8. Never
reach10"
behind or over blade while it is moving.
• Dado blades
under
9. Use a push stick when required and whenever possible,
diameter notespecially
compatible
with small/narrow workpieces and non-through cuts.
10. Know what causes “kickback” and how to prevent it.
with riving11.knife.
Never remove jammed/cutoff workpiece when blade is moving!
• Max Width: 13/16"
Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.
Use G8588
G0833P Machine Labels A
SN
Date
Mfd. for Grizzly in China
713
PANTONE 3005 C or RAL 5005
701
Max. Depth of Cut @ 45˚: 2-1/4"
Max. Dado Width: 13/16"
Weight: 396 lbs.
AMPUTATION
HAZARD!
Always keep
fingers and
hands away from
moving blade.
G0833P Machine Labels C
DANGER
CAUTION
The Model G0833P
COPYRIGHT
© GRIZZLY
spreader/riving
knife is INDUSTRIAL, INC.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
0.1" thick.
Follow
FOR THIS
GRIZZLY
MACHINES ONLY!
DO
NOTthese
REPRODUCE OR CHANGE THIS ARTWORK
DO NOT REPRODUCE OR CHANGE
ARTWORK
requirements
ensure
Grizzlyto will
nottheaccept labels changed without approval. If
WITHOUT
WRITTEN
APPROVAL!
Removing blade
blade
guard is
Disconnect
power
Grizzly will not
accept labelsIfremoved
changed
without
approval.
If
spreader/riving knife works
guard increases
for a artwork
beforechanges
changing are required,
contact us immediately at manuals@grizzly.com.
are required, contact us risk
immediately
manuals@grizzly.com.
safely:
of injury—it at special
cut, some blades or blade
MODEL G0833P
MUST be installed other safeguard
guard and riving
BLADE REQUIREMENTS
POLAR BEAR SERIES™ 10" HYBRID TABLE SAW
when possible.
MUST be used.
knife.
Standard Blades
Specifications
WARNING!
• Diameter: To
10"
Motor: 2 HP, 115V/230V, 60 Hz, Single-Phase
reduce risk of serious injury when using this machine:
Pre-Wired: 230V
1. Read and understand
owner’s manual before operating.
• Max. Body Thickness:
0.094"
12. Make sure blade is stopped before adjusting the height or tilt.
Full-Load Current Rating: 16A at 115V, 8A at 230V
2. Never touch moving blade, and keep hands out of cutting path. 13. Do not perform any operation freehand.
Blade Size: 10" x 5/8" Arbor
• Min. Kerf Thickness:
0.102"
3. Always wear approved
eye protection and respirator.
14. Never use fence and miter gauge at the same time.
Required Blade Kerf Thickness: 0.102"–0.126"
4. Only plug power cord into a grounded outlet.
15. Ensure machine is stable and fence is parallel with blade.
Arbor Speed: 3850 RPM
• Must be aligned
with
5. Always use blade guard/spreader for all through cuts; and use
16. Disconnect power before changing blades or servicing saw.
Max. Rip Capacity: 31-1/2"
riving knifeknife.
for all non-through cuts. If a certain cut cannot be
Max. Depth of Cut @ 90˚: 3-1/4" spreader or riving
17. Plan cuts so that workpieces always remain supported.
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
WARNING!
THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
artwork changes are required, contact us immediately at manuals@grizzly.com.
PANTONE 3005 C or RAL 5005
WARNING
NOTICE
Do not open door
while machine is
connected to power
FOR
or blade is in motion.
PANTONE 151 C or RAL 2005
COLOR CODES
PANTONE 3005 C or RAL 5005
INJURY HAZARD!
710
PANTONE 109 C
• Scale= 1:1
(unless otherwise noted)
PANTONE 109 C
PANTONE 485 C or RAL 3001
PANTONE 151 C or RAL 2005
To reduce risk of death
EYE/LUNG INJURYNOTICE
PANTONE
C or
RAL 5005
or
serious 3005
injury,
read
HAZARD!
manual BEFORE using
Always wear safety
machine.
glasses and
a
COPYRIGHT
© GRIZZLY
INDUSTRIAL,
INC.
To get a new
manual,
respirator
whenONLY! DO NOT
call (800)
523-4777 or OR CHANGE
GRIZZLY
MACHINES
REPRODUCE
using this machine
go to www.grizzly.com.
• Labels MUST be made of
chemical-resistant material
PANTONE 151 C or RAL 2005
CAUTION
COLOR CODES
DANGER
WARNING
***These labels must have individual
letters/numbers.
Do not print with clear background.
WARNING
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
• Labels MUST be made of
chemical-resistant material
711
INJURY/SHOCK
HAZARD!
Disconnect power
before adjustments,
maintenance, or
service.
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
WARNING!
WARNING!
artwork changes
are required, contact us immediately at manuals@grizzly.com.
To reduce risk of death
EYE/LUNG INJURY
INJURY HAZARD!
HAZARD!
Do not open door
COLOR
CODES Always wear safety
while machine
is
glasses and a
connected to power
respirator when
or
blade is in motion.
machine
DANGER
PANTONE 485 Cusing
or RALthis
3001
• Scale= 1:1
(unless otherwise noted)
WARNING!
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com
Rotating blade adjustment handwheels into
stopping positions with excessive force could
result in a loss of blade parallelism with miter
slot, impaired stop-collar accuracy, and
damage to internal components. This type of
damage is not covered by warranty!
CAUTION
WARNING!
(06/13/17)
702
WARNING!
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine
PANTONE 3005 C or RAL 5005
Dado Blades
WARNING
DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE, OR
SERVICE.
Keep door closed
while blade is in
motion. Disconnect
power before
opening door.
damage is not covered by warranty!
artwork changes
The Model G0715P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:
Disconnect power
before changing
blades or blade
guard and riving
knife.
or serious injury, read
FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK
Rotating blade adjustment handwheels into
• Dado blades under 10"
stopping positions with excessive force could WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If
diameter not compatible
The Model
G0833P
result in a loss of blade parallelism with miter
COLOR
CODES
The Model G0833P
with riving knife.
artwork
spreader/riving
knife is changes are required, contact us immediately at manuals@grizzly.com.
slot, impaired stop-collar accuracy, and
spreader/riving knife is
• Max Width: 13/16"
0.1" thick.485
Follow
damage to internal components. DANGER
This type of PANTONE
C or these
RAL 3001
AMPUTATION
0.1" thick. Follow these
requirements to ensure the
damage
is notguard
covered
warranty!power
If blade
is by
Removing blade
Disconnect
HAZARD!
NOTICE
• Labels MUST be made of
chemical-resistant material
HAZARD!
BLADE
REQUIREMENTS
manual
• Labels
MUST be made
ofBEFORE using
Always
wear safety
machine.
Standard
Blades
glasses and a
chemical-resistant
material
To get a new manual,
• Diameter:
10"
respirator when
call (800) 523-4777 or
• Max.using
Body this
Thickness:
0.094"
machine
go to www.grizzly.com.
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
G0833P Machine Labels B
stopping positions with excessive force could
• Scale= 1:1
(unless otherwise noted)
(06/26/15)
AMPUTATION
If blade guard is
Removing blade
HAZARD!
removed for a
guard increases
Always keep
special cut, some
risk of injury—it
fingers and
hands away from MUST be installed other safeguard
MUST be used.
when possible.
moving blade.
Dado Blades
• Dado blades under 10"
diameter not compatible
WARNING
The Model G0833P
with riving knife.
spreader/riving knife is
CAUTION
• Max Width: 13/16"
0.1" thick. Follow these
NOTICE
requirements to ensure the
If blade guard is
Disconnect power
WARNING!
WARNING!
spreader/riving knife works
removed for a
guard increases
before changing
Always keep
WARNING!
WARNING!
To reduce risksafely:
of death
COPYRIGHT © GRIZZLY INDUSTRIAL, INC. INJURY/SHOCK fingers and INJURY risk
EYE/LUNG
INJURY
special
cut,
some
of
injury—it
blades
or
blade
HAZARD!
To reduce risk of death
or serious injury, read
EYE/LUNG
INJURYOR CHANGE
DO NOT
REPRODUCE
THIS
ARTWORK
hands away from MUST be installed other safeguard
HAZARD! guard and riving
orHAZARD!
serious
injury, read
manual BEFOREBLADE
using REQUIREMENTS
Do
not
open
door
HAZARD!
Grizzly will not accept labels changed
without
approval.
If
manual
BEFORE
using
MUST
be used.
when possible.
knife.
moving
blade.
Always
wear safety
power
machine.
Disconnect
Standard Blades
while machine is
Always
wear safetyat manuals@grizzly.com.
machine.
artwork changes are required, contact
us immediately
glasses and a
adjustments,
before
To get a new manual,
connected to power
• Diameter: 10"
glasses and a
To get a new
respirator when
or manual,
maintenance,
call (800) 523-4777 or
or
blade
is
in
motion.
respirator when
call
(800)
523-4777
or
•
Max. Body Thickness: 0.094"
using this machine
go to www.grizzly.com.
service.
using this machine
go to www.grizzly.com.
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
704
717
BLADE REQUIREMENTS
Standard Blades
• Diameter: 10"
• Max. Body Thickness: 0.094"
• Min. Kerf Thickness: 0.102"
• Must be aligned with
spreader or riving knife.
COLOR CODES
DANGER
Disconnect power
before changing
blades or blade
guard and riving
knife.
The Model G0833P
spreader/riving knife is
0.1" thick. Follow these
requirements to ensure the
spreader/riving knife works
safely:
Reduce this risk by
cleaning front rail
before positioning
fence.
Disconnect power
before changing
blades or blade
guard and riving
knife.
Debris on front rail
can misalign fence
and increase risk of
kickback.
To reduce risk of death
or serious injury, read
manual BEFORE using
machine.
To get a new manual,
call (800) 523-4777 or
go to www.grizzly.com.
If blade guard is
removed for a
special cut, some
other safeguard
MUST be used.
Front
WARNING!
707
EYE/LUNG INJURY
HAZARD!
Always wear safety
glasses and a
respirator when
using this machine
Removing blade
guard increases
risk of injury—it
MUST be installed
when possible.
Reduce this risk by
cleaning front rail
before positioning
fence.
AMPUTATION
HAZARD!
Always keep
fingers and
hands away from
moving blade.
Back
WARNING!
• Labels MUST be made of
chemical-resistant material
(06/19/17)
(06/13/17)
G0833P Machine Labels
Scale= 1:1
G0833P Machine Labels 708
B • (unless
otherwise noted)
(Actual Size)
service.
Debris on front rail
can misalign fence
and increase risk of
kickback.
G0833P Fence
(Shown at 40% Actual Size)
Labels & Cosmetics
chemical-resistant material
COPYRIGHT © GRIZZLY INDUSTRIAL, INC.
FOR GRIZZLY MACHINES ONLY! All labels created by Grizzly Industrial, Inc. are
copyrighted and must only be used on Grizzly brand machines. Never use Grizzly’s label
artwork on other brands of machines.
Scale 1:1
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
701
702
703
704
705
706
707
708
709
MACHINE ID LABEL
READ MANUAL LABEL
TABLE SAW WARNING LABEL
RIVING KNIFE CAUTION LABEL
DISCONNECT POWER LABEL
ELECTRICITY LABEL
DON'T OPEN DOOR WARNING LABEL
BLADE GUARD LABEL
HANDWHEELS NOTICE LABEL
710
711
712
713
714
715
716
717
TOUCH-UP PAINT, POLAR BEAR WHITE
EYE/LUNG HAZARD LABEL
GRIZZLY NAMEPLATE G8588
TOUCH-UP PAINT, GRIZZLY GREEN
POLAR BEAR LOGO LABEL
MODEL NUMBER LABEL
GRIZZLY.COM LABEL
FENCE LABEL
P0833P701
P0833P702
P0833P703
P0833P704
P0833P705
P0833P706
P0833P707
P0833P708
P0833P709
P0833P710
P0833P711
P0833P712
P0833P713
P0833P714
P0833P715
P0833P716
P0833P717
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.
-86-
Model G0833P (Mfd. Since 06/17)
WARRANTY CARD
Name _____________________________________________________________________________
Street _____________________________________________________________________________
City _______________________ State _________________________ Zip _____________________
Phone # ____________________ Email _________________________________________________
Model # ____________________ Order # _______________________ Serial # __________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1.
CUT ALONG DOTTED LINE
2.
How did you learn about us?
____ Advertisement
____ Card Deck
4.
5.
6.
____ Catalog
____ Other:
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
3.
____ Friend
____ Website
Cabinetmaker & FDM
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Old House Journal
Popular Mechanics
____
____
____
____
____
____
____
____
____
____
Popular Science
Popular Woodworking
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
Today’s Homeowner
Wood
____
____
____
____
____
____
____
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $50,000-$59,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
What is your age group?
____ 20-29
____ 50-59
____ 40-49
____ 70+
____ 30-39
____ 60-69
How long have you been a woodworker/metalworker?
____ 0-2 Years
____ 2-8 Years
____ 8-20 Years
____ 20+ Years
How many of your machines or tools are Grizzly?
____ 0-2
____ 3-5
____ 6-9
____ 10+
7.
Do you think your machine represents a good value?
_____ Yes
_____No
8.
Would you recommend Grizzly Industrial to a friend?
_____ Yes
_____No
9.
Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times.
_____ Yes
_____No
10. Comments: _____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
WARRANTY AND RETURNS
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising