YUTONG Portable Ice Maker User Manual(33x16)

YUTONG Portable Ice Maker User Manual(33x16)
Congratulations, you have acquired a high quality Hamilton Beach™
Portable Ice Maker. This product allows you to make ice cubes and has
many features that you will find convenient to use. Record the model
number, serial number, and the manufacture date, which can be found on
the label on the back of the unit.
____________________________________________________________________
Portable Ice Maker
model number
serial number
manufacture date
date of purchase
READ ALL INSTRUCTIONS BEFORE USING!
Instruction Manual
To ensure proper use and for your safety, please read the following
instructions completely before operating this appliance.
Parts and Features
IMPORTANT SAFEGUARDS
• When using electrical appliances, basic safety precautions should be
followed, including the following:
1.
2.
3.
Viewing Window
Cover
Control Panel
(see close up)
4. Air Outlet
5. Air Inlet
6. Water Outlet
7. Power Cord
8. Ice Storage Basket
9. Metal Fingers
10. Ice Making Area
• WARNING: BURN HAZARD. Do not touch the Metal Fingers (see # 9 on
Parts and Features list) while the unit is making ice, it may burn your skin.
Children should be supervised by an adult when using this product.
• WARNING: FIRE HAZARD. Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance.
Do not operate the dispenser with a damaged cord. Do not use with an
underrated extension cord or an extension cord without a ground.
• WARNING: SHOCK HAZARD. Unplug the Portable Ice Maker before
cleaning or wiping up spilled water on the unit. Do not attempt to service the
Portable Ice Maker. Do not operate with a damaged cord.
SAVE THIS MANUAL FOR FUTURE USE!
!
No product registration is required for this unit. When making a customer
service call, please have the model number, manufacture date, and serial
number on hand.
A
B
C
D
• Never put anything flammable close to the unit.
CONTROL PANEL CLOSE UP
A.
B.
C.
D.
Ice Storage Basket Full Indicator Light
Add Water Indicator Light
Power Indicator Light
Power Button (On/Off)
1
Note: If there is a water shortage during either stage of the Self-Clean
mode, the Self-Clean mode will automatically shut off. Add more water
and repeat steps 1 - 4.
Cleaning the Outside of the Portable Ice Maker
4. Note: For tough deposits add vinegar to the water and let soak until
the deposits come loose.
To cancel Self-Clean mode, simply press and hold the Power Button
(ON/OFF) for 5 seconds.
•
To maintain maximum efficiency and to prevent bacterial growth in the
portable ice maker, we strongly recommend cleaning every 4 months.
•
Wipe the outside of the Portable Ice Maker with a mild soap and water
mixture. Never use harsh chemicals or abrasive cleaners. Rinse
thoroughly with clean water and dry all surfaces.
•
Do not immerse the unit in water.
Cleaning the Ice Storage Basket and Scoop
The Ice Storage Basket (see # 8 on the Parts and Features list) and scoop
should be removed and cleaned regularly to remove spotting and mineral
deposits.
1. Remove the Ice Storage Basket by pulling it up and out and rinse
with clean water.
2. Clean using a mild soap and warm water mixture. For tough deposits
add vinegar and let soak until the deposits come loose.
Then wash, rinse and dry thoroughly.
3. To replace the ice storage basket, simply slide the basket back into
the reservoir.
4. Repeat steps 1 & 2 for the ice scoop.
Self-Clean Mode Operating Instructions
The Self-Clean mode should be put into operation before you use your
Portable Ice Maker for the first time and/or if there has been a long period
of time without use. The Ice Storage Basket Full Indicator Light, Add
Water Indicator light, and Power Indicator Light (see A, B, and C on the
Parts and Features list) will be on at the same time when the unit is in
Self-Clean mode.
Troubleshooting the Portable Ice Maker
Problem
Possible Causes
Solution
POWER
Indicator Light
is not turning
on
1. Portable Ice Maker is
unplugged.
1. Push plug completely
into outlet.
2. The fuse is
blown/circuit
breaker is tripped.
2a. Replace fuse or reset
circuit breaker.
3. Internal components
are damaged.
3. Call Customer Service.
1. Ice Storage Basket is
full.
1. Remove ice from Ice
Storage Basket.
2. Low-temperature
protection activated.
(ambient
temperature is
lower than 41
degrees F, 5 degrees
C).
2. Move the Portable Ice
Maker to a warmer
place, where the
ambient temperature is
higher than 41 degrees F,
5 degrees C).
ADD WATER
Indicator Light
is on
1. Water Reservoir is
empty.
2. Water supply system
is damaged.
1. Add clean water.
ICE BASKET
FULL and
ADD WATER
Indicator
Lights are on
at the same
time
1. Ice Making Area
may be blocked.
1. Check for ice blocking Ice
Making Area.
2. Internal components
are damaged.
2. Call Customer Service
Stage 1
1. Add equal parts of water and vinegar (1:1) to the unit’s reservoir.
2. Press the Power Button (ON/OFF) (see D on Parts and Features list)
repeatedly for at least 5 seconds to activate the Self-Clean mode.
Note: Self-Clean mode will start automatically after the “Beep” sound.
3. During the Self-Clean mode, the Ice Making Area (see # 10 on the
Parts and Features list) is filled and emptied. The pump will remain in
continuous operation as it feeds water to the Ice Making Area and the
Metal Fingers (see # 9 on the Parts and Features list). This cycle will
repeat itself five times.
ICE BASKET
FULL Indicator
Light is on
4. Upon completion, the Self-Clean mode will automatically shut off.
Stage 2
Cleaning the Water Reservoir and interior of the Portable Ice Maker
IMPORTANT NOTE: Do not clean the Metal Fingers (see #9 on Parts and
Features list).
Make sure the unit is unplugged before attempting to clean and allow
it to warm up to room temperature.
1. Unscrew the cap of the Water Outlet (part # 6 on Parts and Features
list) and drain all the water into a sink or bucket.
2. Remove the Ice Storage Basket.
6
1. Drain the cleaning solution from the reservoir by removing the Water
Outlet cap (see # 6 on the Parts and Features list).
2. Add clean water to the MAX water level mark.
3. Press the Power Button (ON/OFF) repeatedly for at least 5 seconds to
activate the Self-Clean mode again which will now act as a rinse.
4. Upon completion of this final stage of the Self-Clean process, the SelfClean mode will automatically shut off. Proceed to drain the water
from the Water Outlet by removing the cap. Leave the Cover (see # 2
on the Parts and Features list) of the unit open to allow it to air dry.
7
• Regular cleaning of the unit is required for proper operation. Clean the unit
every four months using the instructions in this manual.
SAVE THESE INSTRUCTIONS!
WARNING: Modifying or defeating of the grounding plug can result in a
risk of electric shock.
• This appliance must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock.
• This appliance is equipped with a power cord that has a grounding
wire with a grounding plug. The plug must be plugged into a 3 prong
outlet that is properly installed and grounded.
• Consult a qualified electrician if the grounding instructions are not
completely understood, or if doubt exists as to whether the
appliance is properly grounded.
• Do not under any circumstances cut or remove the third ground
prong from the power cord.
• Do not use an extension cord with this appliance. If the power cord is
too short, have a qualified electrician install an outlet near the desired
location of the unit.
• For best operation, plug the appliance securely into its own electrical
outlet on a dedicated circuit not shared with any other appliances to
prevent blowing a fuse or tripping the circuit breaker.
Getting familiar with your Hamilton Beach
Portable Ice Maker
Features
• Designed for home or office use.
• Using compressor refrigeration technology, the Portable Ice Maker
processes ice cubes quickly and efficiently.
• Ice making process can be watched through Viewing Window (see #1
on Parts and Features list).
• Push-button operation. Indicator lights show the working status of
the unit and provide automatic alerts for when to add more water and
when the Ice Storage Basket (see # 8 on Parts and Features list) is full.
• Self-Clean function can be run to automatically keep the unit clean.
3
3. Pour clean water into the reservoir, and use a clean cloth to wipe down
the sides of the reservoir. Allow all of the water to flow out of the
Water Outlet and replace cap.
Make sure the unit is unplugged before attempting to clean and allow
it to warm up to room temperature.
• Leave a minimum of 8” (20 cm) around the back and sides of the unit for
proper ventilation.
2
Proper Care and Cleaning of the Portable Ice
Maker
•
• If the unit is brought inside from cold outdoor temperatures, allow it to
warm up to room temperature, for at least a few hours beforeoperating.
Ambient temperature of the unit should be not be less than 41 degrees F
(5 degrees C).
• Install the unit in a dry place away from direct sunlight. Do not place
on or near a hot gas or electric burner, or in a heated oven. For indoor use
only.
TABLE OF CONTENTS
PIM Series
• Never turn the unit upside down or tilt more than 45 degrees. If the unit has
been resting on its side for a long period of time, you must position it in the
upright position for approximately 12 hours before turning it on.
• Never use this unit with water that is unsafe to drink or is from an
unknown source. Never use any other liquid in the unit other than drinking
water.
CUSTOMER SERVICE: 716-235-1300
Toll-free 1-800-256-8169
PARTS AND FEATURES LIST.........................................................................2
IMPORTANT SAFEGUARDS..........................................................................3
GROUNDING INSTRUCTIONS AND GETTING FAMILIAR............................4
PROPER INSTALLATION AND LOCATION.....................................................5
PREPARING, LOADING AND OPERATING YOUR ICE MAKER.....................5
CARE AND CLEANING...................................................................................6
TROUBLESHOOTING GUIDE.........................................................................8
• NOTE: Do not let power cord hang over edge of table or counter, or touch
hot surfaces. Do not let the power cord cross over carpeting or other heat
insulators. Do not cover the cord.
Grounding Instructions
2b. If too many items are
plugged into a single
circuit, move some
items to a different plug.
4
Troubleshooting Continued...
Problem
Possible Causes
Solution
Ice making
performance
is poor
1. Air Inlet/Outlet is
blocked
1. Clean the Air Inlet/Outlet
(see # 4 and 5 in
Parts and Features list).
2. Fill with room
temperature water
2. Water temperature is
too high.
3. Move the Portable Ice
Maker to a cooler place,
where the ambient
temperature is lower
than 95 degrees F
(38 degrees C).
3. Ambient
temperature
is too high.
4. Refrigerant is
leaking and/or
Refrigerating system
is damaged.
4. Call Customer Service.
1. Call Customer Service.
1. Fan or pump is
Portable Ice
damaged.
Maker is noisy
Proper Installation and Location
• The Portable Ice Maker is for indoor use only. Do not use outdoors.
• Place the unit on a dry and level surface away from hot gas or
electric burners. Do not place in direct sunlight.
• To ensure your unit works at the maximum efficiency, leave at least
8 inches (20 cm) of clearance between all sides of the unit and any walls.
• To prevent damage to the unit and to avoid injury, do not plug unit
into the power source until reading the instructions first!
• Do not transport or store the Portable Ice Maker upside down or on its
side in order to avoid disrupting the fluids inside the compressor. To
ensure maximum performance, allow the unit to sit upright at room
temperature for at least 3 hours before first use.
Preparing, Loading and Operating Your
Portable Ice Maker
1. It is advisable to clean the unit prior to first use. See the cleaning
instructions on page 6.
2. Ensure the Water Outlet (see # 6 on Parts and Features list) on the
back of the unit is secure.
3. Plug the Portable Ice Maker into the outlet and the Power Indicator
Light (see C on the Parts and Features list) will turn on.
4. Open the Cover (see #2 on the Parts and Features list) and remove
the Ice Storage Basket (see # 8 on the Parts and Features list).
5. Fill the water reservoir up to the MAX water level mark. Use only cold
or room temperature drinking water for making ice. Do not pour hot
water into reservoir. Do not fill above the MAX water level mark.
6. Replace the Ice Storage Basket and close the Cover.
7. Press the Power Button (see D on the Parts and Features list) on the
Control Panel to start making ice.
8. The “Ice Storage Basket Full” Indicator Light (see A on the Parts and
Features list) will turn on when the Ice Storage Basket is full and the
unit will stop making ice automatically. Once the ice has been
removed from the Ice Storage Basket and the Cover closed, the ice
making cycle will continue automatically.
9. The “Add Water” Indicator Light (see B on the Parts and Features list)
will turn on when the water reservoir is empty and the ice making
cycle will stop automatically. Add water to continue using the unit.
5
LIMITED WARRANTY
This warranty applies to products purchased and used in the US and Canada. This
is the only express warranty for this product and is in lieu of any other warranty or
condition.
This product is warranted to be free from defects in materials and workmanship for
a period of one (1) year from the date of original purchase. During this period, your
exclusive remedy is replacement of this product or any component found to be
defective at our option; however, you are responsible for all costs associated with
returning the product to us and our returning a product or component under this
warranty to you. If the product or component is no longer available, we will replace
with a similar one of equal or greater value.
This warranty does not cover glass, filters, wear from normal use, use not in
conformity with the printed directions, or damage to the product resulting from
accident, alteration, abuse, or misuse. This warranty extends only to the original
consumer purchaser or gift recipient. Keep your original sales receipt, as proof of
purchase is required to make a warranty claim. This warranty is void if the product
is used for other than single - family household use or subjected to any voltage and
waveform other than as specified on the rating label (e.g., 115V ~ 60 Hz).
We exclude all claims for special, incidental and consequential damages caused by
breach of express or implied warranty. All liability is limited to the amount of the
purchase price. Every implied warranty, including any statutory warranty or
condition of merchantability or fitness for a particular purpose, is disclaimed
except to the extent prohibited by law, in which case such warranty or condition
is limited to the duration of this written warranty. This warranty gives you specific
legal rights. You may have other legal rights that vary depending on where you live.
Some states or provinces do not allow limitations on implied warranties or special,
incidental, or consequential damages, so the foregoing limitations may not apply to
you.
To make a warranty claim, do not return this appliance to the store. Please call
1.800.256.8169 or 716.235.1300 in the U.S. and Canada or visit hamiltonbeach.com
in the U.S, or hamiltonbeach.ca in Canada. For faster service, please have the model
number, serial number, and manufacture date on hand at the time of the call.
2. Call Customer Service.
PRS Enterprises
3349 Monroe Ave., Suite 328
Rochester, NY 14618
8
9
10
Ver. 1.0
Hamilton Beach® is a registered trademark
of Hamilton Beach, Inc. used under license
by PRS Enterprises.
SAVE THESE INSTRUCTIONS!
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement