Smart Brand SB8544 Operating Instructions Manual
Smart Brand SB8544 is a washing machine with a range of features to make laundry day easier. It has a large capacity, allowing you to wash large loads of laundry in one go, and a variety of wash cycles to suit different fabrics and soil levels. The machine also features an automatic door opening function, which means that the door opens automatically once the programme has finished.
Advertisement
Advertisement
Operating Instructions
Washing Machine
Smart Brand SB8544
2
Contents
Before using your machine for the first time
Description of the washing machine
Advice and tips before washing
Rayon fibres and synthetic fibres
9
9
8
9
7
7
8
9
9
10
10
10
10
10
10
10
5
5
5
5
5
6
6
6
4
4
4
5
4
4
Turn on the main power switch.
Open the washer door and load the washing
Add detergent and fabric softener, as required
Checking the filter and drainage pump
Cleaning the detergent compartment
Cleaning the outside of the machine
Cleaning the inside of the machine to avoid unpleasant smells
Rinse holes under the agitator
Information for test institute
Positioning the washing machine
Programme plate in multiple languages
15
15
16
16
11
11
12
14
11
11
11
16
16
18
18
19
20
20
20
21
16
17
17
18
22
22
22
22
23
23
23
Contents
Before contacting the service division
24
24
28
3
Before using your machine for the first time
Transport protection
Remove any transport protection devices before installing the machine. See the “Transport protection devices” chapter.
Packing material
Please sort waste materials in accordance with local guidelines.
Washer door
• The washer door cannot be opened until the machine is connected to the electricity supply.
• To open the door manually, see the section entitled “The door will not open" in the
“Troubleshooting” chapter.
• It is not possible to start the machine with the door open.
• To open the washer door while a programme is running, see the "Wash" section under the heading "Close the door and press the
Start/Stop button".
Checking water hardness
The quantity of detergent needed depends, amongst other things, on how hard the water is.
See the detergent pack for details. Phone your local water company to check the water hardness in your area.
Note!
Each machine is tested before leaving the factory. A small amount of water may remain in the drain pump, though this does not affect quality or damage the machine.
4
See the Quick guide on the last page.
Safety instructions
General
• Read the operating instructions and keep them in a safe place.
• Installation of water and electricity, if required, should be carried out by a qualified professional.
• The machine should only be used for washing items as described in these instructions. It is not intended for dry cleaning.
• Use only detergent intended for machine washing!
• Remove any transport protection devices before using the machine, see the “Transport protection” chapter.
• Repairs and maintenance relating to safety or performance must be carried out by a qualified professional.
• Damaged mains cables must only be replaced by a qualified electrician.
• The machine is not designed to be used by persons (even children) that are physically or mentally handicapped or lack experience and knowledge. Such persons must receive instruction in how to use the machine from the person responsible for their safety.
• Children must be watched to ensure they do not play with the machine.
Installation
See the “Installation” chapter.
Overflow guard function
If the machine’s water level rises above the normal level, the overflow guard function begins to pump water out and shuts off the water intake. If the water level has not dropped within 60 seconds, the program is terminated.
Transport/Winter storage
If the machine is to be transported or stored in unheated premises where the temperature can fall below freezing, do as follows:
• Empty the filter and drainage pump (see the
“Care and cleaning” chapter).
• Shut off the water to the washing machine, loosen the supply hose to the intake valve and let the water run out from the valve and hose.
• After emptying the pump, a small amount of water may remain in the machine. This does not affect quality or damage the machine.
Recycling
This machine is manufactured and labelled for recycling. In order to prevent injuries, the machine must be made unusable once the decision has been taken to dispose of it. Contact your local authority for information about where and how your machine can be recycled correctly.
5
6
Child safety
Keep an eye on children!
• Always close the door and start the programme immediately once you have added detergent.
• Do not allow small children to use or play with the washing machine.
• Store detergent and fabric softener out of the reach of children.
Automatic door opening
The machine comes with an automatic door opening function, which means that the door opens automatically once the programme has finished.
If you wish to prevent small children or pets from climbing into the machine, you can deactivate the automatic door opening function.
1. Turn off the machine using the main power switch.
2. Press the Door Open button while simultaneously pressing the main power switch. Release the buttons.
3. Press the Key button and the red field goes out. Automatic door opening is now deactivated.
4. Press the Start/Stop button to store the setting.
If you want to reactivate the function, follow the instructions above. When you press the button with the key symbol (point 3), the red fields light up. Store the setting by pressing the Start/Stop button.
Description of the washing machine
3 1. Detergent compartment
2. Main power switch
3. Programme panel
4. Type plate
5. Hatch - drainage pump
6. Drainage pump (behind hatch)
7. Washer door
8. Outer door (not all models)
1 2
4
5,6
Detergent compartment
1. Pre-wash
2. Main wash
3. Fabric softener compartment
2
1
3
7
8
NB!
In the plastic bag containing these instructions and other things, you will find a plastic divider. Place the divider in the detergent compartment if you use liquid detergent.
7
Front panel
1 2
5 6
7
1.
2-4.
5.
Main power switch
Options buttons
Programme selector
3 4
6.
7.
8.
Display window
Start/Stop
Door opening
8
8
Options button
2
Cold
30
40 50
60
95
800
3
1400
4
2.
Button for selecting Temperature
3.
Button for selecting Spin speed
4.
Button for selecting Delayed Start
Advice and tips before washing
Here are some tips that may help you before washing.
Sorting your laundry
Sort items according to:
• how soiled they are
• colour
• material
Clothing
1. Do up zips and close Velcro straps so that they don’t harm fabrics.
2. New coloured items may contain excess dye and should therefore be washed separately the first few times.
3. Turn delicate items inside out. This reduces the risk of burling and fading.
4. Empty pockets and wash them inside out if possible.
Laundry labels
Look at the item's laundry label. The table below shows suitable wash programmes for different materials and wash loads. Using modern washing machines and detergents, for example compact detergents, you can usually wash at lower temperatures. It is a good idea to use trial and error to find out what produces the best results.
Laundry label symbols
Laundry labels Material Program
Cotton, linen, white and light-coloured items.
White 60°C to 95°C
Cotton, linen. Dark-coloured items.
Colour 60°C
Polyester, cotton/polyester, nylon. White items.
Synthetic 60°C
Rayon, acetate, acrylic. Non-colourfast items.
Synthetic 40°C
Polyester, cotton/polyester, nylon. Coloured items.
Synthetic 40°C
Silk and very delicate items Synthetic 30°C
Items labelled with the IWS or Superwash mark
Wool/Hand 40°C
Load
1/1 drum
1/1 drum
1/2 drum
1/2 drum
1/2 drum
1/3 drum
1/3 drum
9
10
Advice and tips before washing
Coloured cotton
Coloured cotton items with the washing instruction
60°C should be washed at 60°C for the first time in order to remove any excess dye. If you do not do so, there is a risk that the colour will run. Use detergent without bleach in order to preserve the colour of the fabric.
Unbleached linen
Unbleached linen fabrics should be washed at
60°C, using detergent containing no bleach or optical whiteners. Heavily-soiled linen can occasionally be washed at higher temperatures, but not too often because the heat can destroy the linen’s shine and strength.
Wool
These fabrics are labelled for either machine wash or for hand wash. The machine’s Wool/Hand programme is at least as gentle as washing by hand.
Wool is especially sensitive to processes such as washing.
If you do not wish to spin dry, you can squeeze out the water using terry towels. In this case select
No spin.
To find out how to select this setting, see the
"Washing" chapter. However, most garments can withstand a short spin. Choose a short spin by selecting a spin speed of 800 rpm or less.
Rayon fibres and synthetic fibres
Materials made of rayon fibres, such as viscose, and some synthetic fibres are very delicate and require much space. Only half fill the drum when washing and choose a programme with a 800 rpm spin or lower.
Note!
Viscose and acetates are fragile when wet.
Save time and energy
Use the White programme to save time and energy. This programme has a shorter main wash than Normal, but is often sufficient for lightly soiled washing.
Economy and efficiency
You can save a lot of energy by not using higher temperature programs than necessary.
• Select Quick if you just need to freshen up shirts or exercise clothes, for example. This will save both water and energy.
• If you select a fast spin speed, this reduces energy consumption when drying in a tumble dryer or drying cabinet.
• Avoid pre-washing. Modern machines and detergents clean effectively without pre-washing. Pre-washing is only necessary for heavily soiled washing.
Detergents
Eco-labelled detergents are less harmful to the environment.
Detergent overdosing does not give better washing results; it merely causes a greater impact on the environment.
Try to use less detergent, and increase only if you are not satisfied with the results.
Note!
Because of environmental concerns we discourage the use of strong chemicals.
When using agents for bleaching or stain removal, there is a risk of rust (corrosion) and discolouration of the machine.
Washing
1
Sort your laundry.
See the "Advice and Tips before washing" section.
Place underwired bras in a laundry net.
Empty pockets. Coins, nails and the like can cause damage to the machine and fabrics. See the "Advice and Tips" section before washing.
2
Turn on the main power switch.
3
Open the washer door and load the washing
If the door is closed, press the Door opening button (key symbol). The red field will light up and the door will open once all water has drained from the machine. Load the laundry. The laundry programme chart shows how much laundry can be washed with each programme.
4
Add detergent and fabric softener, as required
The detergent packaging will have recommendations for how much detergent you should use. The machine holds 7kg of laundry. If you only have a small amount of laundry in the machine, you can reduce the amount of detergent used.
Powder detergent
Pour the powder into the compartment for the main wash, and pre-wash as well if desired.
Prewash
Fabric softener
Main wash
Liquid detergent
When using liquid detergent, follow the detergent manufacturer’s recommendations. We recommend always using a wash ball with very thick liquid detergent.
Wash ball or net
If you use a wash ball or net, place it directly in the drum and select a programme without prewash.
Note!
Detergent overdosing does not give better washing results; it merely causes a greater impact on the environment.
Try using less detergent, and increase only if you are not satisfied with the results.
Fabric softener
Pour the fabric softener into the compartment with the symbol. Follow the recommendations on the fabric softener packaging.
Note!
Do not fill above the compartment’s maximum fill level. Otherwise fabric softener will run in too early, which impairs the washing effect.
11
12
Washing
5
Select the programme
You can select a programme by turning the programme selector. A red field lights up beside the selected programme, and the estimated programme time is shown on the display.
Start the programme by pressing the Start/Stop or go on to options and settings.
Quick
Colour
White
Normal
Heavy
Synthetic
Wool/Hand
Rinse
Spin
Drain
Heavy
Program for heavily soiled laundry, with dirt that needs to be fully dissolved before the main wash.
A pre-wash is used to do this. You can select the temperature freely, so follow the washing instructions for each garment. The highest temperature,
95°C, is suitable for very heavily soiled laundry.
The spin speed can be selected freely. The machine adapts the program time and water consumption to the load size.
Normal
Program for normally to heavily soiled laundry, whites and colors. You can select the temperature freely, so follow the washing instructions for each garment. 60°C is a good temperature for heavily soiled cotton garments, as well as for garments worn next to the skin. Select 40°C if the laundry is less soiled. The spin speed can be selected freely. The machine adapts the program time and water consumption to the load size.
White
A standard program for lightly to moderately soiled laundry. The temperature can be selected freely, so follow the washing instructions for each garment. Garments worn next to the skin ought to be washed at 60°C. The spin speed can be selected freely. The machine adapts the program time and water consumption to the load size.
Colour
Standard program for lightly soiled laundry. The temperature can be selected freely, so follow the washing instructions for each garment. Garments worn next to the skin ought to be washed at 60°C.
Very lightly soiled laundry, however, often comes clean at 40°C. The spin speed can be selected freely.
Quick
Fast program for laundry that just needs freshening up. The program can be run at any temperature, so follow the washing instructions for each garment. The lower the selected temperature, the shorter the program time. Garments worn next to the skin ought to be washed at 60°C. The spin speed can be selected freely.
Synthetic
Program for synthetics, blended materials, and permanent press cotton. Suitable for shirts and blouses. The temperature can be selected freely, so follow the washing instructions for each garment. Garments worn next to the skin ought to be washed at 60°C. Many synthetics will come clean at 40°C too. The maximum spin speed is 800 rpm.
Wool/Hand
A gentle laundry program for wool, silk, and garments that should be washed by hand. The highest temperature is 30°C. This program has a short spin. The maximum spin speed is 800 rpm.
Rinse
This program performs one cold rinse cycle + spin. Suitable for laundry that just needs to be dampened and for cleaning cloths and mops.
Spin or Drain
To be used when you only want to spin the load or drain the water from the machine.
Washing
Programme chart
Program
Heavy
Pre-wash
Yes
Yes
No
Main wash
Long
Long
Long
Temp. °C
95
60
60
1)
Normal
White
No
No
Long
Short
Colour
Quick
Synthetic
No
No
No
Short
Short
Short
Wool/Hand
Rinse
No Short
Spin
1
Test program in accordance with EN 60456.
40
60
40
40
40
30
2)
3)
Rinses
(number)
5
5
5
5
5
5
2
3
3
1
2
40°C program for test institute. Option function 40°C must be selected.
3
Short programme for test institutes. The 60°C option must be selected.
Max. RPM
1400
1400
1400
1400
1400
1400
1400
800
800
1400
1400
Max. load
1/1
1/1
1/1
1/1
1/2
1/2
1/2
1/2
1/3
1/2
1/2
Water consumption
(approx. liter)
85
75
72
72
55
55
25
30
70
15
Energy consumption
(approx. kWh)
Programme time
(approx. hrs and min.)
2.1
1.2
1.19
0.66
0.8
0.5
0.5
0.4
0.5
0.1
0.1
2:45
2:40
2:46
2:29
2:15
1:25
0:45
1:15
0:45
0:20
0:15
The above table presents a few examples of the energy, water and time consumption of a few different programme settings. Consumption can vary according to water pressure, water hardness, water supply temperature, room temperature, load weight and content, variations in the power supply and selected options. In the examples provided here the rinse setting is set to Normal and no options are selected.
13
14
Washing
6
Select options and settings
By changing options and settings you can adjust the washing program to suit your own specific requirements.
40 50
Cold
30 60
95
800
1400
Temperature
Select temperature by pressing the Temperature button until the red field lights up beside the desired temperature.
You can select temperatures between 30°C and
95°C or Cold. If you select Cold, the washing temperature will be the same as that of the water coming into the machine.
For Wool/Hand it is not possible to select a temperature higher than 40°C. See the table.
Spin speed/No spin
Select the spin speed by pressing the Spin button until the red field next to the spin speed you want lights up.
You can select speeds between 800 and 1400 rpm, No spin.
Spin at 800 rpm always signifies short spin.
For certain programmes, it is not possible to select a speed in excess of 800 rpm (see table).
No spin means that the program does not include a spin cycle and ends by draining.
Delayed start
When you select Delayed Start, the machine will start 1-24 hours after you press the Start/Stop button.
• Press the Delayed Start button the same number of times as the number of hours you want to delay the start by (1-24 hours). A lighted red field next to the button indicates that the option has been activated.
• The number of hours delay until start is shown in the display window.
• Press the Start/Stop button.
• The number of hours to start is displayed with a countdown one hour at a time.
• Cancel Delayed Start by pressing the
Start/Stop button for 3 seconds. The red field will go out.
Important!
Remember to press Delayed Start followed by the Start/Stop button to start the programme.
Washing
7
Close the door and press the
Start/Stop button
Time remaining
The time remaining is shown in hours and minutes. Once a programme is selected, the estimated programme time is displayed. This may differ from time to time depending on the temperature of the water entering the machine and the size of the load. If the programme time is longer than the previous wash with the same programme,
"0:01" will be displayed until the programme finishes. This is normal! The next time you use the programme under similar conditions, the estimated programme time will be more accurate.
To add or remove washing after the program starts
If you want to add or remove items after the programme has started, you can stop the programme by pressing and holding the Door opening button
(key symbol) for three seconds. The red field will flash. When you restart the machine, add any extra detergent needed and close the door. The machine continues automatically from the point where the programme was interrupted.
Stopping or changing a programme
You can also stop a programme by pressing the
Start/Stop button for three seconds. To restart the machine, select a new programme, add any extra detergent needed and press the Start/Stop button.
8
Once the program has finished
Once a programme is finished, "End" appears on the display.
The door opens automatically once the program has finished. If you want to deactivate "automatic door opening", see the Child safety chapter.
• Remove the load.
• Turn off the main power switch, this will save energy.
If you have small children or pets at home, close the washer door once you have removed the laundry.
Note!
Do not open the detergent compartment while the machine is running.
15
16
Care and cleaning
Checking the filter and drainage pump
The washing machine has a filter, where coins, hairpins and the like can get caught. To clean the filter and drainage pump:
1. Make sure the machine is empty of water and that it is switched off at the mains.
Cleaning the detergent compartment
Pull the detergent compartment out as far as it will go.
P 1
2 P
S
/S
P 3
P 4
Then pull it up and out as shown in the illustration.
2. Open the hatch for the drainage pump as shown in the illustration.
3. Drain out the water, into a bowl, for example, by unhooking the drainage hose from the pin inside the hatch.
4. Open the pump by screwing the cover anticlockwise. Remove the cover with the filter.
5. Remove any objects or rubbish from the pump housing. Check to see that the pump blades, right at the back, will rotate.
6. Screw on the cover, replace the drainage hose on the hatch pin and close the hatch.
P 1
/S
P 2
P
3
P 4
Rinse the compartment and scrub it clean. Replace the compartment.
Cleaning the outside of the machine
Clean the outside of the machine and the program panel with a mild cleaner. Do not use any solvents, as these can damage the machine.
Note!
Do not run the detergent compartment through a dishwasher!
Do not hose down the machine with water!
Cleaning the inside of the machine to avoid unpleasant smells
Modern detergents often allow clothes to be washed at low temperatures. This means that small deposits can build up in the machine. These, in turn, may lead to unpleasant smells developing.
To avoid this, we recommend running a 95°C wash programme once a month. When you do this, use a small quantity of detergent. It is not necessary to put any washing in the machine.
Care and cleaning
Rinse holes under the agitator
If you think that objects such as nails or paper clips, may have fallen into the wash drum, you should check the container under the agitator.
Such objects can rust and cause spots on clothing. Nails and other sharp objects can cause holes in fabrics.
Do as follows:
1. Insert a screwdriver or the like into the central hole on the agitator and carefully pry to the left.
1
If you have hard water
If you live in an area with hard water (high limescale content), a greyish-white coating may form on the washer drum. To remove this, empty a sachet of citric acid, approx. 20gram, into the washer drum and run any 95°C programme. Repeat if necessary.
2. Grasp the agitator and pull it towards you using your other hand, as shown in the illustration.
2
3. Lift the agitator.
4. Remove any objects.
5. Place the agitator in the mounting hole with the
F-mark towards you. Ensure that all the agitator fasteners are in their holes in the drum. Push it away from you until it catches.
17
18
Troubleshooting
The washer door will not open
1. Check that the main power switch is on.
2. Has the power supply been cut off? Check the house fuses (circuit breakers). The washer door cannot be opened using the button with the key symbol if the power supply has been cut off.
If nothing else works, the washer door can be opened as follows:
• This must only be done in an emergency if the machine's glass door does not open automatically when the programme has finished.
• First check that there is no water left in the machine. If there is any water left and you are unable to run the Drain programme, empty the machine by detaching the drainage hose. This is described under the heading “Checking the Filter and Drainage pump” in the “Care and Cleaning” chapter.
• Make sure that the mains power switch is off and that the plug has been removed from the wall socket.
• Open the hatch to the drainage pump, bottom left as shown in the illustration.
• Pull the handle and the door opens.
• Insert the handle back into its slot and screw it tight. Close the hatch to the drainage pump.
If the glass door does not open when the wash programme is finished, call the service division.
The machine will not start
1. Is the washer door properly closed? Push it firmly.
2. Is there power? Check your home’s fuses.
3. Check that you have not selected Delayed
Start. Stop the programme if you want.
• Unfasten the screws holding the red plastic handle in place.
Troubleshooting
Error messages
If an error occurs during the programme a message is shown on the display. To exit the message after taking measures, turn the machine off and then back on.
The error messages that may be shown are:
Close the door
If the first red field beside the Start/Stop button is flashing, you have tried to start a programme with the door open. Close the door and the programme will start.
Over filling
If F1 is flashing on the display:
1. Shut off the water tap.
2. Call the service division.
Drainage error
If F3 is flashing in the display, there is a problem with drainage. Check:
• that no objects are stuck in the drainage hose outlet.
• that the drainage pump is not blocked by foreign objects. Clear the pump, see the "Care and cleaning" chapter.
• that there are no kinks in the drainage hose.
After taking measures, run the Drain programme or press the Door opening button (key symbol) to empty the machine. If this does not resolve the problem, call the service division.
Water intake error
If F4 is flashing on the display.
Fault with water supply. Check:
• that the tap on the water pipe is open.
• that the filter in the machine’s water intake is not blocked.
1. Shut off the water tap.
2. Unscrew the hose.
3. Clean the filter in the intake valve on the machine.
4. Screw the hose back on.
5. Turn on the tap.
6. Run the program again to check if the fault is fixed.
7. If this does not resolve the problem, call the service division.
Door opening error
if F6 is flashing on the display, call the service division!
19
20
Technical information
Technical data
Height:
Width:
Depth:
Weight:
Cylinder volume:
Max. washing capacity:
Spin speed (rpm)
Rated power:
Heater output:
Water pressure:
Wash drum and liquid compartment material:
Outer casing material:
Water connection:
Drain:
Information for test institute
Europe:
Washing program:
Connection:
Test method for noise measurement:
Power requirement when machine turned off
Power requirement for time-delayed start
Power requirement when programme finished
850mm
595mm
585mm
73kg
50l
7kg
800 - 1400
See type plate.
See type plate.
0,1 - 1 MPa
1 - 10 kp/cm
2
10 - 100 N/cm
2
Stainless steel
Powder-coated and hot-galvanized sheet steel or stainless steel.
1.5m pex pipe
1.7m polypropylene hose 3/4 BSP connection
EN 60456
Normal, 60°C, 7 kg cotton
Cold water 15°C
IEC-60704-2-4
< 0,3 W
< 6,0 W
< 3,0 W
Transport protection
Before the machine is used, the three transport protection devices should be removed as shown below.
Each transport protection device consists of a screw, a washer and a rubber spacer. After the protection device has been removed, the rubber spacer acts as a plug for the holes for the device and also as a damper.
1. First remove the screws and remove the washers.
2. Then remove the rubber spacers.
1
2
3. Finally, the rubber spacers should be turned over and replaced in the transport protection device holes.
Note!
In order to prevent the machine from being damaged when it is transported, use the transport protection device, which locks the entire inner compartment in place. If the transport protection device is missing, you can order one from your retailer.
Item number:
8064206 Rubber spacer
8901037 Bolt
8061767 Washer
Order three of each item!
21
22
Installation
Positioning the washing machine
The washing machine can be installed as a builtin or freestanding unit. Position the machine so that the electrical plug is easily accessible.
A. Built-in
The washing machine can be installed under a counter top with a working height of 850-900 mm.
Leave a 5 mm space around the entire machine, including between the rear edge of the top cover and the wall behind it.
B. Freestanding
The washing machine can be positioned beside or under a tumble dryer.
Adjusting the feet
Keep the noise that the machine produces to a minimum by adjusting the feet so that the machine is steady and balanced on the floor. Tighten the lock nuts.
Connection to water supply
Water connection should be carried out by an appropriately qualified person. Connect the machine using the accompanying supply hose. Water pressure should be 0.1–1MPa (approx.
1–10kp/cm
2
; 10–100N/cm
2
). There should be a stopcock on the water pipe.
If the pipes are newly installed, it may be wise to flush them through so that any dirt is washed away. Otherwise, dirt can clog the filter in the machine’s water intake and cut off the water supply.
Locking nut
Only use the inlet hose supplied with the machine.
Do not reuse old or other loose inlet hoses.
Installation
Drainage connection
The machine is supplied with a connected drainage hose that can be fastened to a laundry sink or similar. The height must be 600 - 900 mm above floor level.
The lower position (600 mm) is always preferable.
Ensure that the drainage hose has no kinks.
600-900 mm
The machine can also be connected to the drain via a spigot connection. In this case the hose should also be 600-900 mm above the floor. The internal diameter of the hole should be at least 18 mm.
• Cut the nipple
• Remove burrs from the hole.
See the illustration.
Electrical installation
Electrical connections must be via a plug connected to an earthed wall socket or by cable for fixed installation, with all-pole disconnection, by a qualified professional.
Connection on delivery
The machine is supplied as 1-Phase, 230V, 50Hz, heat output 2000W and has a 10A plug. Any residual current devices must be type A.
Note!
Repairs and maintenance relating to safety or performance must be carried out by a qualified professional.
Programme plate in multiple languages
Certain machines include double-sided programme plates in different languages (see the detergent compartment and the bag with the user handbook that comes with the machine).
You can replace or turn the card yourself to get the language most appropriate for you.
To remove the card from its holder in the detergent compartment, press the card with your thumb and push it sideways (see picture).
Minimum 18 mm
The card will then bend slightly and you can easily remove it. To fit the card, bend it slightly in order to easily insert it into the holder in the detergent compartment.
23
24
Service
Before contacting the service division
Before you contact the service division, make sure that you know the model designation, type designation and serial number.
The model designation can be found on the detergent compartment. Type designation and serial number can be found on the type plate above the washer door.
Type designation WMxx0
TYPE: WMxx xxx x xxxxxxx M xxxxxxxW
Serial number (12 digits)
000000000000
Model designation
Type plate
Your notes
25
26
Your notes
Your notes
27
Quick guide
1
Washing
1. Empty pockets and refasten zips.
2. Read the item’s laundry label.
3. Sorting laundry.
Note!
Place underwired bras in a laundry net.
2
Load the laundry
1. Press the main power switch.
2. If the door is closed, press the Door opening button (key symbol). The red field lights up and the door opens after a few seconds.
3. Load the laundry and close the door.
3
Detergent compartment
1. Pour detergent into the main wash compartment, and pre-wash compartment as well if required. Pour fabric softener into the compartment on the right with the -symbol.
2. If you use liquid detergent, follow the detergent manufacturer’s recommendations.
4
Select the programme
1. Select a programme by turning the programme selector.
2. Select any options and settings.
3. Press the Start/Stop button.
5
Program finished
1. The text END on the display indicates that the wash programme has finished.
2. The washer door opens automatically once the programme has finished.
3. Remove the load.
4. Turn off the main power switch.
If you have small children or pets at home, close the washer door once you have removed the laundry.
28
Art. No.: xx xxx xx. Rev. 01. We reserve the right to make changes.
Printed on environmentally friendly paper that meets the requirements of MIljöförbundet and Naturskyddsföreningen.
Advertisement
