Thermalright
Archon SB-E X2
Archon SB-E X2
Assembly package
× 1
× 1
× 4
× 4
× 1
× 1
× 4
× 1
× 8
4
× 4
× 1
4
× 1
× 1
× 4
8
Thermalright Archon SB-E X2
Intel 775/1155/1156/1366
Exploded view
Important!
Before proceeding with installation, please check for the most up-to-date instructions at
www.thermalright.com
Fan Clip
Anti Vibration Pads
Heatsink Body
TY141 Fan
Pressure Adjustable
Mounting Plate
Anchoring Bracket Mount
Screw Pillar
Angled Wrench
Thumbscrew Cap
White Plastic Washer
Intel Multiple Support Backplate
Backplate cap
1
Component
1
4
2
5
3
6 7
8 9 10 11 12 13
14 15 16
1
Heatsink Body ×1
4
AMD Backplate ×1
7
LGA2011 Screw Pillar
Type C ×4
10
Backplate cap ×1
13
PWM Y-cable ×1
2
5
8
Anchoring Bracket
Mount ×1
Pressure Adjustable
Mounting Plate ×1
Thumbscrew Cap
×4
11
Angled Wrench x1
14
Thermal paste ×1
16
TY141 Fan ×2
3
Intel Multiple Support
Backplate ×1
6
Screw Pillar
×4
9
White Plastic Washer
×4
12
Anti Vibration Pad ×4
15
Fanclip ×4
The Ultimate Cooling Solutions!
www.thermalright.com
2
Installation Instructions:
Step 1:
Step 1 : Part Installation
Apply the Anti-Vibration Pads to each corner of the Heatsink Body. Then pull the long end of the Fan
Clips and make it go through the bottom side hole closest to the edge as shown in the close-up diagram.
Repeat this with the top hole.
Step 2:
1366
775
1156
1155
Step 2 : Backplate Installation
Choose the correct Backplate according to your system (Intel), and adjust the Screw Cylinders according to your platform. Place the four white washers through the protruding screws.
Step 3: Step 4:
3
Step 3 : backplate cap
Use the Backplate Cap only for the 775 platform.
Step 4 : Pass the Backplate through mounting holes on the mainboard, then fit the Screw Pillars to the Backplate screws.
Step 5: Step 6:
Step 5 : Place the Anchoring Bracket Mount on top of the four Screw Pillars. Tighten the 4 Screw
Pillars with the Thumbscrew Caps.
Step 7:
Step 6 : Applying Thermal Paste
Apply the Thermal Paste to the base of the
Heatsink and the surface of the CPU evenly.
1/2 rotation
(-10 lb.) (+10 lb.)
Step 7 : Mounting Plate
Fit the heatsink then secure it by placing the Pressure Adjustable Mounting Plate, and tighten the hexagonal screws to the Anchoring Bracket Mount.
Tighten the central knob on the Pressure Adjustable Mounting Plate with the Angled Wrench as seen fit. (The central knob can add an addition 30lbs of force to the cooler, each half rotation adds 10 lbs of force for a total of 70lbs)
Step 8: Step 9:
Step 8 : Fan Installation
Place the included TY-141 fan onto the Heatsink
Body. And then secure it with the TY-141 Fan
Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-141 Fan.
Step 9 : Installation completed
Connect the two TY-141 fans to the PWM Y-Cable then connect the cable to the CPU PWM Fan socket on the motherboard. Installation complete.
The Ultimate Cooling Solutions!
www.thermalright.com
4
Thermalright Archon SB-E X2
Intel LGA 2011
Exploded view
Important!
Before proceeding with installation, please check for the most
Fan Clip
Heatsink Body
Anti Vibration Pads
TY141 Fan
5
Pressure Adjustable
Mounting Plate
Anchoring Bracket Mount
LGA2011 Screw
Pillar Type C
Angled Wrench
Thumbscrew Cap
Component
1
4
2
5
3
6 7
8 9 10 11 12 13
14 15 16
1
Heatsink Body ×1
4
AMD Backplate ×1
7
LGA2011 Screw Pillar
Type C ×4
10
Backplate cap ×1
13
PWM Y-cable ×1
2
5
8
Anchoring Bracket
Mount ×1
Pressure Adjustable
Mounting Plate ×1
Thumbscrew Cap
×4
11
Angled Wrench x1
14
Thermal paste ×1
16
TY141 Fan ×2
3
Intel Multiple Support
Backplate ×1
6
Screw Pillar
×4
9
White Plastic Washer
×4
12
Anti Vibration Pad ×4
15
Fanclip ×4
The Ultimate Cooling Solutions!
www.thermalright.com
6
Installation Instructions:
Step 1:
Step 1 : Part Installation
Apply the Anti-Vibration Pads to each corner of the Heatsink Body. Then pull the long end of the Fan
Clips and make it go through the bottom side hole closest to the edge as shown in the close-up diagram.
Repeat this with the top hole.
Step 2:
Step 2 : Screw Pillar Installation
Screw on the 4 LGA2011 Type C Screw Pillars into the heatsink studs on the Intel ILM Assembly Frame around the processor socket.
Step 3:
7
Step 3 : Anchoring Mount Installation
Place the Anchoring Bracket Mount on top of the 4 LGA2011 Type C Screw Pillars. Then tighten the 4
LGA2011 Type C Screw Pillars with the Thumbscrew Caps.
Thermalright Archon SB-E X2
Step 4:
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
Step 5:
1/2 rotation
(-10 lb.) (+10 lb.)
Step 5 : Mounting Plate
Fit the heatsink then secure it by placing the Pressure Adjustable Mounting Plate, and tighten the hexagonal screws to the Anchoring Bracket Mount.
Tighten the central knob on the Pressure Adjustable Mounting Plate with the Angled Wrench as seen fit. (The central knob can add an addition 30lbs of force to the cooler, each half rotation adds 10 lbs of force for a total of 70lbs)
Step 6: Step 7:
Step 6 : Fan Installation
Place the included TY-141 fan onto the Heatsink
Body. And then secure it with the TY-141 Fan
Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-141 Fan.
Step 7 : Installation completed
Connect the two TY-141 fans to the PWM Y-Cable then connect the cable to the CPU PWM Fan socket on the motherboard. Installation complete.
The Ultimate Cooling Solutions!
www.thermalright.com
8
Thermalright Archon SB-E X2
AM2/AM2+/AM3/AM3+/FM1/FM2
Exploded view
Important!
Before proceeding with installation, please check for the most up-to-date instructions at
www.thermalright.com
Fan Clip
Anti Vibration Pads
Heatsink Body TY141 Fan
Pressure Adjustable
Mounting Plate
Anchoring Bracket Mount
Screw Pillar
Angled Wrench
Thumbscrew Cap
9
Component
1 2
4 5
3
6 7
8 9 10 11 12 13
14 15 16
1
Heatsink Body ×1
4
AMD Backplate ×1
7
LGA2011 Screw Pillar
Type C ×4
10
Backplate cap ×1
13
PWM Y-cable ×1
2
5
8
Anchoring Bracket
Mount ×1
Pressure Adjustable
Mounting Plate ×1
Thumbscrew Cap
×4
11
Angled Wrench x1
14
Thermal paste ×1
16
TY141 Fan ×2
3
Intel Multiple Support
Backplate ×1
6
Screw Pillar
×4
9
White Plastic Washer
×4
12
Anti Vibration Pad ×4
15
Fanclip ×4
The Ultimate Cooling Solutions!
www.thermalright.com
10
Installation Instructions:
Step 1:
Step 1 : Part Installation
Apply the Anti-Vibration Pads to each corner of the heatsink. Then pull the long end of the Fan Clips and make it go through the bottom side hole closest to the edge as shown in the close-up diagram.
Repeat this with the top hole.
Step 2:
Step 2 : Backplate Installation
Choose the correct Backplate according to your system (AMD). Pass the Backplate through mounting holes on the mainboard, then fit the Screw Pillars to the Backplate screws.
Step 3:
11
Step 3 : backplate cap
Place the Anchoring Bracket Mount on top of the four Screw Pillars. Tighten the 4 Screw Pillars with the
Thumbscrew Caps.
Step 4:
Step 4 : Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Nuts.
Step 5:
1/2 rotation
(-10 lb.) (+10 lb.)
Step 5 : Mounting Plate
Fit the heatsink then secure it by placing the Pressure Adjustable Mounting Plate, and tighten the hexagonal screws to the Anchoring Bracket Mount.
Tighten the central knob on the Pressure Adjustable Mounting Plate with the Angled Wrench as seen fit. (The central knob can add an addition 30lbs of force to the cooler, each half rotation adds 10 lbs of force for a total of 70lbs)
Step 6: Step 7:
Step 6 : Fan Installation
Place the included TY-141 fan onto the
Heatsink Body. And then secure it with the TY-
141 Fan Clips, by pulling the Fan Clips to place the four ends at the four holes on the TY-141 Fan.
Step 7 : Installation completed
Connect the two TY-141 fans to the PWM Y-Cable then connect the cable to the CPU PWM Fan socket on the motherboard. Installation complete.
The Ultimate Cooling Solutions!
www.thermalright.com
12
Thermalright Archon SB-E X2
Technical Spec
Heatsink Specifications:
Dimension: Length 155mm x Width 53.66mm x Height 170.2mm
Weight: 777g (Heatsink only)
Heatpipe: 6mm heatpipe*8 units
Copper Base: C1100 Pure copper nickel plated
Fan Specification:
Dimension: L152mm x H140mm x W26.5m
Weight: 175g
Fan speed: 900~1300RPM (PWM controlled)
Fan noise: 21~25dBA MAX
Airflow: 28.32~73.64CFM MAX
Connector: 4 Pin (PWM Fan connector)
13
Thermalright Archon SB-E X2
155
40 57.5
53
The Ultimate Cooling Solutions!
www.thermalright.com
14
Thermalright Archon SB-E X2
15
The Ultimate Cooling Solutions!
www.thermalright.com
TEL: +886-2-8663-6630
FAX: +886-2-8663-6645
EMAIL: [email protected]
