Panasonic TH-85PB1W, TH-103PB1W Interactive Plasma Display Operating Instructions

Below you will find brief information for Interactive Plasma Display TH-85PB1W, Interactive Plasma Display TH-103PB1W. This document provides detailed instructions for operating your new Interactive Plasma Display, including information on connections, basic controls, picture and sound adjustments, setup menus, troubleshooting, and more.
PDF Download
Document
Model No.
TH-85PB1W
TH-103PB1W
Operating Instructions
Display Operations
Interactive Plasma Display
English
Please read these instructions before operating your set
and retain them for future reference.
TQZW560
Dear Panasonic Customer
Welcome to the Panasonic family of customers. We hope that you will have many years of
enjoyment from your new Plasma Display.
To obtain maximum benefit from your set, please read these Instructions before making
any adjustments, and retain them for future reference.
Retain your purchase receipt also, and note down the model number and serial number of
your set in the space provided on the rear cover of these instructions.
Visit our Panasonic Web Site
http://panasonic.net
Table of Contents
Important Safety Instructions.................................. 2
Important Safety Notice ........................................... 3
Safety Precautions ................................................... 4
Accessories .............................................................. 7
Accessories Supply ................................................. 7
Remote Control Batteries ........................................ 8
Connections .............................................................. 9
AC cord connection and xing, cable xing ............. 9
Video equipment connection ................................. 10
AUDIO OUT Terminals connection .........................11
VIDEO and COMPONENT / RGB IN connection ...11
HDMI connection ................................................... 12
DVI-D IN connection .............................................. 12
PC Input Terminals connection .............................. 13
SERIAL Terminals connection ............................... 14
Power On / Off......................................................... 15
Selecting the input signal ...................................... 17
Basic Controls ........................................................ 18
ASPECT Controls ................................................... 20
Digital Zoom ............................................................ 21
On-Screen Menu Displays ..................................... 22
Adjusting Pos./Size ................................................ 23
Picture Adjustments ............................................... 26
Advanced settings ................................................. 27
Picture Proles ....................................................... 28
Saving proles ....................................................... 29
Loading proles ..................................................... 30
Editing proles ....................................................... 30
Sound Adjustment .................................................. 31
SDI Sound Output ................................................. 31
Setup menu ............................................................. 32
Day/Time Setup / On/Off Timer Setup ................... 33
Day/Time Setup ..................................................... 33
On/Off Timer Setup................................................ 33
ii
Touch-Pen Settings ................................................ 34
Screensaver (For preventing image retention) .... 35
Setup of Screensaver Time ................................... 36
Reduces screen image retention .......................... 37
Extended life settings ............................................ 37
ECO Mode settings................................................. 40
Customizing the Input labels................................. 41
Function Button Settings....................................... 42
No activity power off .............................................. 43
Menu Display Duration / OSD Brightness ............ 43
OSD Language ........................................................ 43
Display orientation ................................................. 43
Setup for MULTI DISPLAY ...................................... 44
How to Setup MULTI DISPLAY ............................. 44
ID Remote Control Function .................................. 45
Setup for Portrait .................................................... 46
How to setup Portrait ............................................. 46
Setup for Input Signals .......................................... 48
Component / RGB-in select ................................... 48
YUV / RGB-in select .............................................. 48
Signal menu .......................................................... 49
Options Adjustments ............................................. 52
Weekly Command Timer ....................................... 55
Audio input select .................................................. 57
Input Search .......................................................... 58
Troubleshooting ..................................................... 59
List of Aspect Modes ............................................. 60
Applicable Input Signals ........................................ 61
Shipping condition ................................................. 62
Command list of Weekly Command Timer ........... 63
Specications ......................................................... 64
Customer Service ................................................... 78
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: To reduce the risk of electric shock, do not remove cover or back.
No user-serviceable parts inside. Refer servicing to qualied service personnel.
The lightning flash with
arrowhead within a triangle
is intended to tell the user
that parts inside the product
are a risk of electric shock
to persons.
The exclamation point within
a triangle is intended to
tell the user that important
operating and servicing
instructions are in the papers
with the appliance.
WARNING : To prevent damage which may result in re or shock hazard, do not expose this apparatus to
rain or moisture.
Do not place containers with water (ower vase, cups, cosmetics, etc.) above the set.
(including on shelves above, etc.)
WARNING : 1) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to
qualied service personnel.
2) Do not remove the grounding pin on the power plug. This apparatus is equipped with a three pin
grounding-type power plug. This plug will only t a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the grounding plug.
1
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11) Only use attachments / accessories specied by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart / apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15) To prevent electric shock, ensure the grounding pin on the AC cord power plug is securely connected.
2
Important Safety Notice
WARNING
1) To prevent damage which may result in re or shock hazard, do not expose this appliance to dripping
or splashing.
Do not place containers with water (ower vase, cups, cosmetics, etc.) above the set. (including on
shelves above, etc.)
No naked ame sources, such as lighted candles, should be placed on / above the set.
2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied
service personnel.
3) Do not remove the earthing pin on the power plug. This apparatus is equipped with a three pin earthing-type
power plug. This plug will only t an earthing-type power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact an electrician.
Do not defeat the purpose of the earthing plug.
4) To prevent electric shock, ensure the earthing pin on the AC cord power plug is securely connected.
CAUTION
This appliance is intended for use in environments which are relatively free of electromagnetic elds.
Using this appliance near sources of strong electromagnetic elds or where electrical noise may overlap with the
input signals could cause the picture and sound to wobble or cause interference such as noise to appear.
To avoid the possibility of harm to this appliance, keep it away from sources of strong electromagnetic elds.
IMPORTANT INFORMATION
If a display is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many
injuries, particularly to children, can be avoided by taking simple precautions such as:
• Using cabinets or stands recommended by the manufacturer of the display.
• Only using furniture that can safely support the display.
• Ensuring the display is not overhanging the edge of the supporting furniture.
• Not placing the display on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture
and the display to a suitable support.
• Not standing the displays on cloth or other materials placed between the display and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the display or its controls.
Trademark Credits
• VGA is a trademark of International Business Machines Corporation.
• Macintosh is a registered trademark of Apple Inc., USA.
• SVGA, XGA, SXGA and UXGA are registered trademarks of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.
• HDMI, the HDMI Logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Note:
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent image retention
to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.
3
Safety Precautions
WARNING
Setup
This Plasma Display is for use only with the following optional accessories. Use with any other type of optional
accessories may cause instability which could result in the possibility of injury.
(All of the following accessories are manufactured by Panasonic Corporation.)
• Pedestal ......................................................................... TY-ST85P12 (for TH-85PB1W),
TY-ST103PF9 (for TH-103PB1W)
• Mobile stand for Display ................................................. TY-ST85PB1 (for TH-85PB1W)
• Floor stand ..................................................................... TY-ST85PF12 (for TH-85PB1W)
• Wall-hanging bracket (vertical) ....................................... TY-WK85PV12 (for TH-85PB1W),
TY-WK103PV9 (for TH-103PB1W)
• Ceiling-hanging bracket ................................................. TY-CE85PS12 (for TH-85PB1W),
TY-CE103PS10 (for TH-103PB1W)
• BNC Dual Video Terminal Board .................................... TY-FB9BD
• HD-SDI Terminal Board .................................................. TY-FB9HD
• HD-SDI Terminal Board with audio ................................ TY-FB10HD
• Dual Link HD-SDI Terminal Board .................................. TY-FB11DHD
• Dual HDMI Terminal Board ............................................ TY-FB10HMD
• DMB-T PAL Tuner Board ................................................ TY-FB12DTH*1
• DVB-T Tuner Board ........................................................ TY-FB11DTA*2
• DVI-D Terminal Board .................................................... TY-FB11DD
• AV Terminal Box ............................................................. TY-TB10AV
• Electronic Pen kit for Interactive Plasma Display ........... TY-TPEN1PBW / TY-TPEN1PBU*3
• Remote Pointer kit for Interactive Plasma Display ......... TY-TPEN1RMW / TY-TPEN1RMU*3
• Wireless Module............................................................. ET-WM200E / ET-WM200U*3
*1 Only for Hong Kong.
*2 Only for Australia.
*3 The model numbers of these optional accessories differ according to destination.
Always be sure to ask a qualied technician to carry out set-up.
Small parts can present choking hazard if accidentally swallowed. Keep small parts away from young children. Discard
unneeded small parts and other objects, including packaging materials and plastic bags/sheets to prevent them from
being played with by young children, creating the potential risk of suffocation.
Do not place the Plasma Display on sloped or unstable surfaces, and ensure that the Plasma Display does
not hang over the edge of the base.
• The Plasma Display may fall off or tip over.
Do not place any objects on top of the Plasma Display.
• If water is spills onto the Plasma Display or foreign objects get inside it, a short-circuit may occur which could result in
re or electric shock. If any foreign objects get inside the Plasma Display, please consult your local Panasonic dealer.
Transport only in upright position!
• Transporting the unit with its display panel facing upright or downward may cause damage to the internal circuitry.
Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table
cloths and curtains.
For sufcient ventilation;
(TH-85PB1W)
If using the pedestal (optional accessory), leave a space of 10 cm or more at the top, left and right, and 15 cm
or more at the rear, and also keep the space between the bottom of the display and the oor surface.
If using some other setting-up method, follow the manual of it. (If there is no specic indication of installation
dimension in the installation manual, leave a space of 10 cm or more at the top, bottom, left and right, and 15 cm
or more at the rear.)
(TH-103PB1W)
If using the pedestal (optional accessory), leave a space of 30 cm or more at the top, left and right, and 20 cm
or more at the rear, and also keep the space between the bottom of the display and the oor surface.
If using some other setting-up method, follow the manual of it. (If there is no specic indication of installation dimension in
the installation manual, leave a space of 30 cm or more at the top, bottom, left and right, and 20 cm or more at the rear.)
4
Safety Precautions
When installing the Plasma Display vertically;
Turn down the power switch for the downward direction when you install the Plasma Display vertically.
And set “Display orientation” to “Portrait” in Setup menu. (see page 43)
When using the Plasma Display
The Plasma Display is designed to operate on 200 - 240 V AC, 50/60 Hz.
Do not cover the ventilation holes.
• Doing so may cause the Plasma Display to overheat, which can cause re or damage to the Plasma Display.
Do not stick any foreign objects into the Plasma Display.
• Do not insert any metal or ammable objects into the ventilations holes or drop them onto the Plasma Display, as
doing so can cause re or electric shock.
Do not remove the cover or modify it in any way.
• High voltages which can cause severe electric shocks are present inside the Plasma Display. For any inspection,
adjustment and repair work, please contact your local Panasonic dealer.
Ensure that the mains plug is easily accessible.
An apparatus with CLASS I construction shall be connected to a mains socket outlet with a protective earthing connection.
Do not use any power supply cord other than that provided with this unit.
• Doing so may cause re or electric shocks.
Securely insert the power supply plug as far as it will go.
• If the plug is not fully inserted, heat may be generated which could cause re. If the plug is damaged or the wall
socket is loose, they shall not be used.
Do not handle the power supply plug with wet hands.
• Doing so may cause electric shocks.
Do not do anything that may damage the power cable. When disconnecting the power cable, pull on the plug body, not the cable.
• Do not damage the cable, make any modications to it, place heavy objects on top of it, heat it, place it near any
hot objects, twist it, bend it excessively or pull it. To do so may cause re and electric shock. If the power cable is
damaged, have it repaired at your local Panasonic dealer.
If the Plasma Display is not going to be used for any prolonged length of time, unplug the power supply plug
from the wall outlet.
If problems occur during use
If a problem occurs (such as no picture or no sound), or if smoke or an abnormal odour starts to come out
from the Plasma Display, immediately unplug the power supply plug from the wall outlet.
• If you continue to use the Plasma Display in this condition, re or electric shock could result. After checking that
the smoke has stopped, contact your local Panasonic dealer so that the necessary repairs can be made. Repairing
the Plasma Display yourself is extremely dangerous, and shall never be done.
If water or foreign objects get inside the Plasma Display, if the Plasma Display is dropped, or if the cabinet
becomes damages, disconnect the power supply plug immediately.
• A short circuit may occur, which could cause re. Contact your local Panasonic dealer for any repairs that need to be made.
5
Safety Precautions
CAUTION
When using the Plasma Display
Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display.
• Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands
or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result.
Be sure to disconnect all cables before moving the Plasma Display.
• If the Plasma Display is moved while some of the cables are still connected, the cables may become damaged,
and re or electric shock could result.
Disconnect the power supply plug from the wall socket as a safety precaution before carrying out any
cleaning.
• Electric shocks can result if this is not done.
Clean the power cable regularly to prevent it becoming dusty.
• If dust built up on the power cord plug, the resultant humidity can damage the insulation, which could result in re.
Pull the power cord plug out from the wall outlet and wipe the mains lead with a dry cloth.
Do not burn or breakup batteries.
• Batteries must not be exposed to excessive heat such as sunshine, re or the like.
This Plasma Display radiates infrared rays, therefore it may affect other infrared communication equipment.
Install your infrared sensor in a place away from direct or reected light from your Plasma Display.
Cleaning and maintenance
The front of the display panel has been specially treated. Wipe the panel surface gently using only a cleaning
cloth or a soft, lint-free cloth.
• If the surface is particularly dirty, wipe with a soft, lint-free cloth which has been soaked in pure water or water in
which neutral detergent has been diluted 100 times, and then wipe it evenly with a dry cloth of the same type until
the surface is dry.
• Do not scratch or hit the surface of the panel with ngernails or other hard objects, otherwise the surface may
become damaged. Furthermore, avoid contact with volatile substances such as insect sprays, solvents and thinner,
otherwise the quality of the surface may be adversely affected.
If the cabinet becomes dirty, wipe it with a soft, dry cloth.
• If the cabinet is particularly dirty, soak the cloth in water to which a small amount of neutral detergent has been
added and then wring the cloth dry. Use this cloth to wipe the cabinet, and then wipe it dry with a dry cloth.
• Do not allow any detergent to come into direct contact with the surface of the Plasma Display. If water droplets get
inside the unit, operating problems may result.
• Avoid contact with volatile substances such as insect sprays, solvents and thinner, otherwise the quality of the
cabinet surface may be adversely affected or the coating may peel off. Furthermore, do not leave it for long periods
in contact with articles made from rubber or PVC.
6
Accessories
Accessories Supply
Check that you have the accessories and items shown
Operating
Instruction book
Remote Control
Transmitter
N2QAYB000691
Batteries for the Remote
Control Transmitter
(R6 Size &times; 2)
Display Operations
Network Operations
Power supply cord
Fixing band &times; 2
TMME203
TH-85PB1W
Clamper &times; 1
TMM15412-2
Use the clamper when
connecting a LAN cable.
(refer to “Operating Instructions,
Network Operations”)
Ferrite core &times; 2
J0KG00000014
Use the Ferrite cores to comply with the EMC standard.
(refer to “Operating Instructions, Network Operations”)
These accessories will be used by professional installers when they install the unit.
TH-85PB1W
Eyebolt cap &times; 1
Eyebolt &times; 1
Allen wrench
Blind sheet &times; 1
(M12)
TH-103PB1W
Eyebolt cap &times; 3
Blind sheet &times; 1
Allen wrench
7
Accessories
Remote Control Batteries
Requires two R6 batteries.
1. Pull and hold the hook, then open
the battery cover.
2. Insert batteries - note correct
polarity ( + and -).
3. Replace the cover.
“R6” size
+
+
-
Helpful Hint:
For frequent remote control users, replace old batteries with Alkaline
batteries for longer life.
Precaution on battery use
Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.
Disposal of batteries should be in an environment-friendly manner.
Observe the following precaution:
1. Batteries shall always be replaced as a pair. Always use new batteries when replacing the old set.
2. Do not combine a used battery with a new one.
3. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
4. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
5. Battery replacement is necessary when remote control acts sporadically or stops operating the Plasma Display set.
6. Do not burn or breakup batteries.
7. Batteries must not be exposed to excessive heat such as sunshine, re or the like.
8
Connections
AC cord connection and xing, cable xing
TH-85PB1W
TH-103PB1W
– AC cord xing
Unplug the AC cord
Close
Push until
the hook clicks.
1 Plug the AC cord into
Open
the display unit.
Plug the AC cord until
it clicks.
2 Fix the AC cord with
the clamper.
Note:
Make sure that the
AC cord is locked on both
the left and right sides.
2. Pull off.
1. Keep the
knob pressed.
– Cable xing bands
Unplug the
AC cord
pressing the
two knobs.
Note:
When disconnecting the AC
cord, be absolutely sure to
disconnect the AC cord plug
at the socket outlet rst.
Secure any excess cables with bands as required.
Note:
Two xing bands are supplied with this unit. In case of securing cables at three (four) positions, please purchase it separately.
Pass the attached cable
xing band through the
clip as shown in the
gure.
To secure cables connected to Terminals, wrap the cable xing band around them
then pass the pointed end through the locking block, as shown in the gure.
While ensuring there is sufcient slack in cables to minimize stress (especially
in the power cord), rmly bind all cables with the supplied xing band.
To tighten:
To loosen:
Push the catch
Pull
1
2
Pull
9
Connections
Video equipment connection
SLOT: Terminal board (optional
accessories) insert slot
(see page 4)
Note:
The lower side slot is for terminal board
with 2-slot width. The terminal board
with 1-slot width does not function when
installed in the lower side slot.
AV IN (VIDEO): Composite Video Input Terminal
(see page 11)
COMPONENT/RGB IN: Component/RGB Video
Input Terminal (see page 11)
SERIAL:
Control the Plasma Display
by connecting to PC.
(see page 14)
DVI-D IN: DVI-D Input Terminal (see page 12)
PC IN: PC Input Terminal Connect to video
terminal of PC or equipment with Y,
PB(CB) and PR(CR) output. (see page 13)
10
AUDIO OUT
Connect to sound
equipment.
(see page 11)
AV IN (HDMI): HDMI Input
Terminal (see page 12)
Connect to video equipment
such as VCR or DVD player.
WIRELESS
MODULE, LAN:
Refer to “Operating
Instructions, Network
Operations”.
Connections
AUDIO OUT Terminals connection
audio equipment
Stereophonic sound code
line-in
VIDEO and COMPONENT / RGB IN connection
Note:
Additional equipment, cables and adapter plugs
shown are not supplied with this set.
VIDEO
OUT
L
RCA-BNC
Adapter plug
R
AUDIO L-R:
Shared with VIDEO and
COMPONENT/RGB IN
AUDIO
OUT
VCR
Notes:
• Change the “Component/RGB-in select” setting in the “Setup”
menu to “Component” (when Component signal connection) or
“RGB” (when RGB signal connection). (see page 48)
• Signals input to COMPONENT/RGB IN terminals correspond to
Sync on G or Sync on Y.
L
DVD Player
AUDIO
R OUT
RCA-BNC
Adapter plug
Computer
RGB Camcorder
Y
PB
PR
Y, PB, PR,
OUT
11
Connections
HDMI connection
[Pin assignments and signal names]
Signal name
Pin No.
1
2
3
4
5
6
7
8
9
10
Pin No.
11
T.M.D.S Data2+
T.M.D.S Data2
Shield
T.M.D.S Data2T.M.D.S Data1+
T.M.D.S Data1
Shield
T.M.D.S Data1T.M.D.S Data0+
T.M.D.S Data0
Shield
T.M.D.S Data0T.M.D.S Clock+
Signal name
T.M.D.S Clock
Shield
12
T.M.D.S Clock-
13
CEC
14
Reserved
(N.C. on device)
15
16
17
18
19
SCL
SDA
DDC/CEC
Ground
+5V Power
Hot Plug Detect
19
18
3 1
HDMI cable
4 2
HDMI
AV OUT
DVD player
Note:
Additional equipment and HDMI cable shown are not supplied with this set.
DVI-D IN connection
Shared with PC IN.
PC with DVI-D
video out
Stereo mini plug (M3)
DVI-video cable (Within 5 m)
DVI-D Input Connector
Pin Layouts
1
Pin No.
8
9
16
17
24
Connection port view
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
T.M.D.S. data 2T.M.D.S. data 2+
T.M.D.S. data 2 shield
DDC clock
DDC data
T.M.D.S. data 1T.M.D.S. data 1+
T.M.D.S. data 1 shield
Pin No.
13
14
15
16
17
18
19
20
21
22
23
24
Signal Name
+5 V DC
Ground
Hot plug detect
T.M.D.S. data 0T.M.D.S. data 0+
T.M.D.S. data 0 shield
T.M.D.S. clock shield
T.M.D.S. clock+
T.M.D.S. clock-
Notes:
• Additional equipment and cables shown are not supplied with this set.
• Use the DVI-D cable complying with the DVI standard. Image deterioration may occur depending on the length or
the quality of the cable.
12
Connections
PC Input Terminals connection
Shared with DVI-D IN.
COMPUTER
Conversion adapter
(if necessary)
(Female)
Mini D-sub 15p
RGB
PC cable
(Male)
Audio
Stereo mini plug (M3)
Connect a cable which matches
the audio output terminal on the computer.
Notes:
• With regard to the typical PC input signals that are described in the applicable input signals list (see page 61), adjustment
values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight
PC input signal types that are not included in the list.
• Computer signals which can be input are those with a horizontal scanning frequency of 15 to 110 kHz and vertical scanning
frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.)
• The display resolution is a maximum of 1,440 &times; 1,080 dots when the aspect mode is set to “4:3”, and 1,920 &times; 1,080
dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible
to show ne detail with sufcient clarity.
• The PC input terminals are DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will
need to make setting changes to the computer at the time of connection.
• Some PC models cannot be connected to the set.
• There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal.
• The computer shown in the illustration is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specied
frequency range.
• Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector.
• Change the “Component/RGB-in select” setting in the “Setup” menu to “Component”
(when Component signal connection) or “RGB” (when RGB signal connection). (see page 48)
Signal Names for Mini D-sub 15P Connector
5
4
10 9
3
2
8
1
7
6
15 14 13 12 11
Pin No.
Signal Name
Pin No.
Signal Name
Pin No.
Signal Name
1
R (PR/CR)
6
GND (Ground)
11
NC (not connected)
2
G (Y)
7
GND (Ground)
12
SDA
3
B (PB/CB)
8
GND (Ground)
13
HD/SYNC
4
NC (not connected)
9
+5 V DC
14
VD
5
GND (Ground)
10
GND (Ground)
15
SCL
Pin Layout for PC Input
Terminal
13
Connections
SERIAL Terminals connection
The SERIAL terminal is used when the Plasma Display is controlled by a computer.
Note: To use serial control for this unit, make sure to set the “Control I/F Select” in the “Network Setup” menu to
“RS-232C”. (refer to “Operating Instructions, Network Operations”)
COMPUTER
(Male)
9
5
8
4
7
3
6
2
1
Pin layout for SERIAL Terminal
RS-232C Straight cable
(Female)
D-sub 9p
Notes:
• Use the RS-232C straight cable to connect the computer to the Plasma Display.
• The computer shown is for example purposes only.
• Additional equipment and cables shown are not supplied with this set.
The SERIAL terminal conforms to the RS-232C interface
specication, so that the Plasma Display can be controlled
by a computer which is connected to this terminal.
The computer will require software which allows the
sending and receiving of control data which satisfies
the conditions given below. Use a computer application
such as programming language software. Refer to the
documentation for the computer application for details.
Signal names for D-sub 9P connector
Communication parameters
These signal names are those of computer specications.
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
Flow control
RS-232C compliant
Asynchronous
9600 bps
None
8 bits
1 bit
-
Basic format for control data
The transmission of control data from the computer
starts with a STX signal, followed by the command, the
parameters, and lastly an ETX signal in that order. If there
are no parameters, then the parameter signal does not
need to be sent.
STX
C1 C2 C3
Start
(02h)
:
P1 P2 P3 P4 P5
Colon
Parameter(s)
(1 - 5 bytes)
3-character
command (3 bytes)
End
(03h)
Details
RXD
TXD
GND
Non use
(Shorted in this set)
NC
Command
Command
PON
POF
AVL
AMT
IMS
ETX
Notes:
• If multiple commands are transmitted, be sure to wait for
the response for the rst command to come from this unit
before sending the next command.
• If an incorrect command is sent by mistake, this unit will
send an “ER401” command back to the computer.
• S1A and S1B of Command IMS are available only when
a dual input terminal board is attached.
• Consult your local Panasonic dealer for detail instructions
on command usage.
14
Pin No.
2
3
5
4 • 6
7
8
1 • 9
DAM
Parameter
None
None
**
0
1
None
SL1
S1A
S1B
VD1
YP1
HM1
DV1
PC1
NW1
None
ZOOM
FULL
JUST
NORM
ZOM2
ZOM3
SJST
SNOM
SFUL
14:9
Control details
Power ON
Power OFF
Volume 00 - 63
Audio MUTE OFF
Audio MUTE ON
Input select (toggle)
SLOT input (SLOT INPUT)
SLOT input (SLOT INPUT A)
SLOT input (SLOT INPUT B)
VIDEO input (VIDEO)
COMPONENT/RGB IN input
(COMPONENT)
HDMI input (HDMI)
DVI-D IN input (DVI)
PC IN input (PC)
Network input (NETWORK)
Screen mode select (toggle)
Zoom, Zoom1
16:9
Just, Just1 (For Video/SD/HD signal)
4:3, 4:3 (1)
Zoom2 (For Video/SD/HD signal)
Zoom3 (For Video/SD/HD signal)
Just2 (For HD signal)
4:3 (2) (For HD signal)
4:3 Full (For HD signal)
14:9 (For Video/SD/HD signal)
With the power off, this display responds to PON command
only.
Power On / Off
Connecting the AC cord plug to the Plasma Display.
Fix the AC cord plug securely to the Plasma
Display with the clamper. (see page 9)
Connecting the plug to the Wall Outlet
Notes:
• Main plug types vary between countries. The power
plug shown at right may, therefore, not be the type
tted to your set.
• When disconnecting the AC cord, be absolutely
sure to disconnect the AC cord plug at the socket
outlet rst.
Press the Power switch on the Plasma Display to
turn the set on: Power-On.
Right side surface
Main Power
On / Off Switch
Remote Control
Sensor
Power Indicator
Power Indicator: Green
[Starting up the network]
It takes some time for the network to start up just
after the power is turned on.
During that time, “Network Setup” in the “Setup” menu
is grayed out and cannot be set.
Press the
button on the remote control to turn the Plasma Display off.
Power Indicator: Red (standby)
Press the
button on the remote control to turn the Plasma Display on.
Power Indicator: Green
Turn the power to the Plasma Display off by pressing the
unit, when the Plasma Display is on or in standby mode.
switch on the
Note:
During operation of the power management function, the power indicator turns
orange in the power off state.
15
Power On / Off
When rst switching on the unit
Following screen will be displayed when the unit is turned on for the rst time.
Select the items with the remote control. Unit buttons are invalid.
Note:
The screens are not displayed if a tuner board has been equipped when setting up. Also they will not be
displayed from the next time the power is turned on after the settings are completed once.
Make the settings in the following menus as necessary.
OSD Language (see page 43)
Day/Time Setup (see page 33)
Display orientation (see page 43)
OSD Language
OSD Language
Day/Time Setup
Display orientation
Display orientation
Day/Time Setup
English (UK)
Time
Deutsch
MON 99:99
Set
Day
Time
Fran&ccedil;ais
Italiano
MON
99:99
Landscape
Portrait
Espa&ntilde;ol
ENGLISH (US)
Day/Time Setup
Time
MON 99:99
Set
Day
Time
Select
TUE
10:00
Set
Select the
language.
2 Set.
1
Select “Day” or
“Time”.
2 Setup “Day” or
“Time”.
1
1
Select “Set”.
2
Set.
For vertical installation,
select “Portrait”.
2 Set.
1
Power ON warning message
The following message may be displayed when turning the unit power ON:
No activity power off Precautions
’No activity power off’ is enabled.
If “No activity power off” in Setup menu is set to “Enable”, a warning message is displayed every time
the power is turned ON. (see page 43)
This message display can be set with the following menu: Options menu
Power On Message (see page 54)
16
Selecting the input signal
Press to select the input signal to be played back from the equipment which has
been connected to the Plasma Display.
Input signals will change as follows:
PC
NETWORK
VIDEO
COMPONENT*
DVI
HDMI
PC: PC input terminal in PC IN.
NETWORK: Network input terminal in LAN or WIRELESS MODULE.
VIDEO: Video input terminal in AV IN (VIDEO).
COMPONENT*: Component or RGB input terminal in COMPONENT/RGB IN.
HDMI: HDMI input terminal in AV IN (HDMI).
DVI: DVI input terminal in DVI-D IN.
* “COMPONENT” may be displayed as “RGB” depending on the setting of
“Component/RGB-in select”. (see page 48)
When an optional Terminal Board is installed:
PC
NETWORK
SLOT INPUT
VIDEO
COMPONENT
ENTER /
HDMI
DVI
+/
VOL
-/
MENU
SLOT INPUT: Input terminal in Terminal Board
INPUT
Note:
When a Terminal Board incompatible with the Plasma Display is installed,
“Non-Compatible Function Board” is displayed.
When a Terminal Board with dual input terminals is installed:
PC
NETWORK
SLOT INPUT A
SLOT INPUT B
VIDEO
COMPONENT
HDMI
DVI
SLOT INPUT A, SLOT INPUT B: Dual input terminal in Terminal Board.
Notes:
• Selecting is also possible by pressing the INPUT button on the unit.
• Outputs the sound as set in “Audio input select” in the Options menu. (see page 57)
• Select to match the signals from the source connected to the component/RGB input terminals. (see page 48)
• Image retention (image lag) may occur on the plasma display panel when a still picture is kept on the panel for an
extended period. The function that darkens the screen slightly is activated to prevent image retention (see page 59),
but this function is not the perfect solution to image retention.
17
Basic Controls
Main Unit
Right side
surface
ENTER/
+
/
VOL
-
Brightness Sensor
Detects the brightness in
the viewing environment
Remote control sensor
Power Indicator
The Power Indicator will light.
• Power-OFF .... Indicator not illuminated (The
unit will still consume some
power as long as the power
cord is still inserted into the wall
outlet.)
• Standby ........ Red
Orange (When “Slot power” is
set to “On”. See page 54)
Orange (Depending on the
type of the function board
installed, when the power is
supplied to the slot)
Orange (When “Control
I/F Select” is set to “LAN”
or “WEB Control” is set to
“On”. Refer to “Operating
Instructions, Network
Operations”)
• Power-ON ...... Green
• PC Power management (DPMS)
......................... Orange (With PC input signal.
See page 40)
• DVI-D Power management
......................... Orange (With DVI input signal.
See page 40)
18
/
Enter / Aspect button
(see page 20, 22)
Volume Adjustment
Volume Up “+” Down “–”
When the menu screen is displayed:
“+” : press to move the cursor up
“–” : press to move the cursor down
(see page 22)
MENU
INPUT
MENU Screen ON / OFF
Each time the MENU button is pressed, the
menu screen will switch. (see page 22)
Normal Viewing
Picture
Sound
Pos. /Size
Setup
INPUT button
(INPUT signal selection)
(see page 17)
Main Power On / Off Switch
Basic Controls
Remote Control Transmitter
ACTION button
Press to make selections.
ASPECT button
Press to adjust the aspect.
(see page 20)
Standby (ON / OFF) button
The Plasma Display must rst be
plugged into the wall outlet and turned
on at the power switch (see page 15).
Press this button to turn the Plasma
Display On, from Standby mode.
Press it again to turn the Plasma
Display Off to Standby mode.
POS./SIZE button
(see page 23)
PICTURE button
(see page 26)
Sound mute On / Off
Press this button to mute the
sound.
Press again to reactivate sound.
Sound is also reactivated when
power is turned off or volume level
is changed.
N button
(see page 25, 26, 27, 31)
POSITION buttons
INPUT button
Press to select Input signal
sequentially. (see page 17)
ECO MODE (ECO)
Press to change the ECO MODE
setup status. (see page 40)
FUNCTION buttons (FUNCTION)
(see page 42)
OFF TIMER button
The Plasma Display can be preset to switch to
stand-by after a xed period. The setting changes
to 30 minutes, 60 minutes, 90 minutes and 0
minutes (off timer cancelled) each time the button
is pressed.
30 min
60 min
90 min
0 min (Cancel)
When three minutes remain, “Off timer 3 min”
will ash.
The off timer is cancelled if a power interruption
occurs.
AUTO SETUP button
Automatically adjusts the position/
size of the screen. (see page 23)
SET UP button (see page 32)
SOUND button (see page 31)
Volume Adjustment
Press the Volume Up “+” or Down “–”
button to increase or decrease the
sound volume level.
R button (see page 22)
Press the R button to return to
previous menu screen.
RECALL button
Press the “RECALL” button to display
the current system status.
1 Input label
2 Aspect mode (see page 20)
Audio input (see page 57)
Prole name (see page 30)
NANODRIFT Saver operating
(see page 38)
3 Touch Pen mode On/Off
(see page 34)
4 Off timer
The off timer indicator is
displayed only when the off
timer has been set.
5 Clock display (see page 54)
1
PC
4:3
COMPONENT
Memory name: MEMORY2
NANODRIFT
Touch-Pen
5
2
On
3
90min
4
10:00
Off timer
Digital Zoom (see page 21)
19
ASPECT Controls
The Plasma Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema
format picture.
Note:
Be aware that if you put the display in a public place for commercial purposes or a public showing
and then use the aspect mode select function to shrink or expand the picture, you may be violating
the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other
people for commercial purposes without the prior permission of the copyright holder.
Press repeatedly to move through the aspect options:
For details about the aspect mode, please see “List of Aspect Modes” (page 60).
[from the unit]
ENTER/
+
The aspect mode changes each time the ENTER button is pressed.
/
VOL
-
/
For VIDEO (S VIDEO) signal input:
4:3
Zoom1
For PC signal input:
4:3
Zoom
Zoom2
16:9
Zoom3
16:9
14:9
Just
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
Zoom1
Zoom2
Zoom3
16:9
14:9
Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i,
750 (720) / 60p • 50p]:
4:3
Just
4:3 Full
14:9
Zoom1
16:9
Zoom2
Zoom3
[For Touch Pen mode]
The aspect is xed as “16:9” and you cannot switch.
Notes:
• The aspect mode is memorized separately for each input terminal.
• Do not allow the picture to be displayed in 4:3 mode for an extended period, as this can cause a permanent image
retention to remain on the Plasma Display Panel.
All Aspect mode
Set “All Aspect” to “On” in Options menu to enable the extended aspect mode (page 54). When All Aspect mode, the aspect
mode of pictures is switched as follows. For details about the aspect mode, please see “List of Aspect Modes”. (page 60)
For VIDEO (S VIDEO) signal input:
4:3
Zoom1
For PC signal input:
4:3
Zoom
Zoom2
16:9
Zoom3
16:9
14:9
Just
For SD signal input (525 (480) / 60i • 60p, 625 (575) / 50i • 50p):
4:3
Zoom1
Zoom2
Zoom3
16:9
14:9
Just
For HD signal input [1125 (1080) / 60i • 50i • 60p • 50p • 24p • 25p • 30p • 24sF, 1250 (1080) / 50i, 750 (720) / 60p • 50p]:
4:3 Full
Zoom1
Zoom2
Zoom3
16:9
14:9
Just1
Just2
4:3 (1)
4:3 (2)
20
Digital Zoom
This displays an enlargement of the designated part of the displayed image.
1
Display the operation guide.
Exit
Press to access Digital Zoom.
The operation guide will be displayed.
1
During Digital Zoom, only the following buttons can be operated.
[Remote control]
OFF TIMER button
[Unit]
ENTER/
+
VOL button
/
VOL
MUTE button
-
VOL button
/
MENU
POSITION /
ACTION button
2
INPUT
Select the area of the image to be enlarged.
Press on the enlargement location to select.
The cursor will move.
Exit
2
3
Select the magnication required for the enlarged display.
Each time this is pressed, the magnication factor changes.
This is shown in the image being displayed.
s1
4
s2
s3
s4
Return to normal display (quit Digital Zoom).
Touch Pen mode during Digital Zoom
The electronic pen cannot be used while the image is
enlarged with Digital Zoom during Touch Pen mode.
Press to exit from the Digital Zoom. The electronic pen can be used when Digital Zoom is
cancelled.
Notes:
• When power goes OFF (including “Off Timer” operation), Digital Zoom terminates.
• The Digital Zoom function cannot be selected while in the following operation state:
When MULTI DISPLAY Setup is On (see page 44).
When Portrait Setup is On (see page 46).
When Screensaver (except for Negative image) is running (see page 35)
• While Digital Zoom is in operation, “Adjusting Pos./Size” cannot be used.
21
On-Screen Menu Displays
Remote Control
Unit
1 Display the menu screen.
MENU
Press to select.
(Example: Picture menu)
2 Select the item.
Normalise
Each time the MENU button is pressed, the
menu screen will switch.
Normal Viewing
Picture
Setup
Sound
Pos./Size
Select.
Picture
ENTER/
Normal
+
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Press several times.
/
VOL
25
0
0
0
5
-
Press.
Select.
/
Normal
Memory save
Memory load
Memory edit
(Example: Picture menu)
Set.
3 Set.
ENTER/
+
/
VOL
-
4 Exit the menu.
Press.
Set.
/
MENU
Press several times.
Press.
Press
to return to the previous menu.
Menu display list
Note: Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal, input and menu setting.
Picture menu
Setup menu
Pos./Size menu
Sound menu
Picture
Normalise
Setup
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Memory save
Memory load
Memory edit
Normal
25
0
0
0
5
Normal
1/2
Normalise
Auto Setup
Touch-Pen Settings
Signal
Screensaver
Extended life settings
ECO Mode settings
Input label
Function Button Settings
Component/RGB-in select
No activity power off
Menu Display Duration
OSD Brightness
OSD Language
RGB
Disable
30 S
5
English (UK)
see page 26-30
Setup
MULTI DISPLAY Setup
Portrait Setup
On/Off Timer Setup
Day/Time Setup
Network Setup
Display orientation
see page 32-51
22
Pos./Size
1/2
Sound
Normalise
Normal
H-Pos
H-Size
V-Pos
V-Size
Dot Clock
Clock Phase
Clamp Position
1:1 Pixel Mode
see page 23-25
Normal
Output Select
Sound Mode
Bass
Mid
Treble
Balance
Surround
0
0
0
0
0
0
0
Off
SDI Sound Output
Left Channel
Right Channel
Sound Out
Level Meter
2/2
see page 31
Landscape
SPEAKERS
Normal
0
0
0
0
Off
2/2
Channel 1
Channel 1
Off
Off
Adjusting Pos./Size
1
Press to display the Pos./Size menu.
2
Press to select the menu to adjust.
3
Press to adjust the menu.
4
Press to exit from adjust mode.
Pos./Size
Normalise
Auto Setup
H-Pos
H-Size
V-Pos
V-Size
Dot Clock
Clock Phase
Clamp Position
1:1 Pixel Mode
Normal
0
0
0
0
0
0
0
Off
Note:
Unadjustable items are grayed
out.
Adjustable items differ depending
on the input signal and the
display mode.
Notes:
• Adjustment details are memorized separately for different input signal formats (Adjustments for component signals are
memorized for 525 (480) / 60i &middot; 60p, 625 (575) / 50i &middot; 50p, 1125 (1080) / 60i &middot; 50i &middot; 60p &middot; 50p &middot; 24p &middot; 25p &middot; 30p &middot; 24sF,
1250 (1080) / 50i, 750 (720) / 60p &middot; 50p each, and RGB/PC/Digital signals are memorized for each frequency.)
• If a “Cue” or “Rew” signal from a VCR or DVD player is received, the picture position will shift up or down. This picture
position movement cannot be controlled by the Picture Pos./Size function.
Auto Setup
When inputting a PC signal as an example, “H-Pos/V-Pos”, “H-Size/V-Size”, “Dot Clock” and “Clock
Phase” are automatically corrected.
This setting is enabled under the following conditions:
• When inputting an analog signal (Component/PC):
This setting is enabled if “Component/RGB-in select” (see page 48) in Setup menu is “RGB”.
• When inputting a digital signal (HDMI/DVI):
A PC format signal enables this setting.
When the signal is not PC format, this setting is enabled only if “Over Scan” (see page 24) is “Off” or
“1:1 Pixel Mode” (see page 25) is “On”. “H-Size/V-Size” is not automatically adjusted.
This setting will be invalid and will not work under the following conditions:
• When NETWORK input is selected.
• When VIDEO signal input
• During Multiple display, Portrait display or Digital Zoom.
• Aspect is set to “Just”
• “Display size” in the Options menu (see page 53) is set to “On”
Using Remote Control
When
on the remote control is pressed, “Auto Setup” will be executed.
When Auto Setup does not work, “Invalid” is displayed.
Auto mode
When the “Auto Setup“ is set to “Auto” in the Options menu (see page 54), automatic position adjustment starts:
• When the display power is turned ON.
• When the input signal is switched.
23
Adjusting Pos./Size
Notes:
• If the dot clock frequency of an analog signal is 162 MHz or higher, “Dot Clock” and “Clock Phase”
cannot be automatically corrected.
• When digital signal input, Dot Clock and Clock Phase cannot be made.
• Auto Setup may not work when a cropped or dark image is input. In such case, switch to a bright image
with borders and other objects are clearly shown, and then try auto setup again.
• Depending on the signal, out of alignment may occur after Auto Setup. Carry out ne tuning for the
position/size as required.
• If Auto Setup cannot set properly for vertical frequency 60Hz XGA signal (1024&times;768@60Hz,
1280&times;768@60Hz, and 1366&times;768@60Hz), pre-selecting the individual signal in “XGA Mode” (see page
49) may results in correct Auto Setup.
• Auto Setup does not work well when a signal such as additional information is superimposed out of
valid image period or intervals between synchronizing and image signals are short, or for image signal
with tri-level synchronizing signal added.
• If Auto Setup cannot adjust correctly, select “Normalise” once and press ACTION ( ), then adjust
Pos./Size manually.
H-Pos
Adjust the horizontal position.
V-Pos
Adjust the vertical position.
H-Size
Adjust the horizontal size.
V-Size
Adjust the vertical size.
Dot Clock
(During Component/PC input signal)
Periodic striped pattern interference (noise) may occur when a striped pattern is displayed. If this happens,
adjust so that any such noise is minimized.
Clock
Phase
(During Component/PC input signal)
Eliminate the ickering and distortion.
Over scan Turn image over scan On/Off.
Congurable signals are as follows:
525i, 525p, 625i, 625p, 750/60p, 750/50p (Component Video, RGB, DVI, SDI, HDMI)
On
Off
Notes:
• When “Off” is set, “H-Size” and “V-Size” cannot be adjusted.
• When the “Display size” is set to “On” in the Options menu, this setting will be invalid. (see page 53)
24
Adjusting Pos./Size
Clamp Position
(During Component/PC input signal)
Adjusts the clamp position when black parts of the image have no detail due to underexposure
or are tinged with green.
Optimum value for Clamp Position adjustment
When black parts have no detail due to underexposure (blackout)
Value that causes least blackout is the optimum.
When black parts are tinged with green
Value that cancels the greenishness without causing blackout is the optimum.
1:1 Pixel Mode
Adjusts the display size when 1125i, 1125p or 1250i signal is input.
Notes:
• Select On when you would like to replay 1920 &times; 1080 input signal.
• Applicable input signal;
1125 (1080) / 50i &middot; 60i &middot; 24sF &middot; 24p &middot; 25p &middot; 30p &middot; 50p &middot; 60p, 1250 (1080) / 50i
• Select Off when ickering is shown around the image.
• H-Size and V-Size cannot be adjusted when On is selected.
Off
On
1:1 Pixel Mode
When the input signal is a 2k1k signal (2048 &times; 1080 / 24p, 2048 &times; 1080 / 24sF), the display size
(2k1k)
is adjusted as follows.
(For 2k1k signals)
Off
On (Left)
On (Center)
On (Right)
Note:
2k1k signals can only be received when the Dual Link HD-SDI Terminal Board (TY-FB11DHD) is installed.
Helpful Hint (
/
Normalise
Normalisation)
While the Pos./Size display is active, if either the N button on the remote control is pressed at any time or the ACTION
( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
25
Picture Adjustments
1
Press to display the Picture menu.
2
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by looking at the picture behind the menu.
Note:
Menu that cannot be adjusted is grayout. Adjustable menu changes depending on signal,
input and menu setting.
Picture
Normalise
Press “ ” or “ ” button to switch between modes.
Dynamic
Normal
Cinema
Monitor
Normal
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
25
0
0
0
5
Normal
For viewing in standard (evening lighting) environments.
This menu selects the normal levels of Brightness
and Contrast.
Normal
Dynamic
For viewing in brighter environments.
This menu selects higher than normal levels of
Brightness and Contrast.
Cinema
For use in viewing tone-focused pictures with
brightness reduced.
Press to enter
Advanced settings.
Advanced settings
Enables ne picture adjustment at a professional
level (see next page).
Picture Mode during Touch Pen mode
“Picture Mode” is xed to “Normal” during Touch
Pen mode.
Advanced settings
Normalise
Monitor
For use when creating broadcast or movie content.
With this picture, even if the overall average picture
level (APL) changes, the brightness of areas with
the same signal level does not change.
Normal
0
0
Black extension
Input level
Gamma
W/B High R
W/B High G
W/B High B
W/B Low R
W/B Low G
W/B Low B
2.2
0
0
0
0
0
0
Notes:
• When “Monitor” is selected in Picture Mode, the
following menu items cannot be set.
Extended life settings: Peak limit (see page 38)
MULTI DISPLAY Setup menu: Video Wall
Uniformity (see page 45)
Portrait Setup menu: Video Wall Uniformity
(see page 47)
• If you would like to change the picture and colour of
the selected Picture menu to something else, adjust
using the items in the Picture menu. (see next page)
Press “ ” or “ ” button to switch between modes.
Normal (9300K)
Helpful Hint (
/
Normalise
Cool (11500K)
Warm (6500K)
Normalisation)
While the “Picture” menu is displayed, if either the N button on the remote control is pressed at any time or the
ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
26
Picture Adjustments
Item
Contrast
Brightness
Colour
Hue
Sharpness
Effect
Less
Adjustments
More
Darker
Brighter
Less
More
Reddish
Greenish
Less
More
Selects the proper brightness
and density for the room.
Adjusts for easier viewing of
dark pictures such as night
scenes and black hair.
Adjusts colour saturation.
Notes:
• You can change the level of each function
(Contrast, Brightness, Colour, Hue, Sharpness)
for each Picture Mode.
• The setting details for Normal, Dynamic,
Cinema and Monitor respectively are memorized
separately for each input terminal.
• In Contrast, there is not a noticeable change
even when contrast is increased with a bright
picture or reduced with a dark picture.
Adjusts for nice skin colour.
Adjusts picture sharpness.
Advanced settings
Item
Black
extension
Effect
Details
Less
More
Less
More
Down
Up
W/B High
R
Less
More
W/B High
G
Less
More
W/B High
B
Less
More
Less
More
Less
More
Less
More
Input level
Gamma
W/B Low R
W/B Low G
W/B Low B
Adjusts the dark shades of the image in gradation.
Adjustment of parts which are extremely bright and hard to see.
2.0
2.2
2.4
2.6
Adjusts the white balance for light red areas.
Adjusts the white balance for light green areas.
Adjusts the white balance for light blue areas.
Adjusts the white balance for dark red areas.
Adjusts the white balance for dark green areas.
Adjusts the white balance for dark blue areas.
Notes:
• Carry out “W/B” adjustment as follows.
1. Adjust the white balance of the bright sections using the “W/B High R”, “W/B High G” and “W/B High B” settings.
2. Adjust the white balance of the dark sections using the “W/B Low R”, “W/B Low G” and “W/B Low B” settings.
3. Repeat steps 1 and 2 to adjust.
Steps 1 and 2 affect each other’s settings, so repeat each step in turn to make the adjustment.
• The adjustment values are memorized separately for each input terminal.
• The adjustment range values should be used as an adjustment reference.
Helpful Hint (
/
Normalise
Normalisation)
On the remote control unit, while the “Advanced settings” menu is displayed, if either the N button is pressed at any time or
the ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
27
Picture Proles
Up to 8 combinations of picture adjustment values (in the Picture menu and Advanced settings) can be stored in the
display memory as proles and applied as needed, for a convenient way to enjoy your preferred picture settings.
Picture
Normalise
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Dynamic
18
0
0
0
3
Normal
Picture
Save proles(page 29)
Memory save
Memory load
Memory edit
Normalise
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Load proles(page 30)
Edit proles(page 30)
Normal
25
0
0
0
5
Normal
Save proles
Edit the prole
Delete or rename
the prole
Save the picture
adjustment values in
the MEMORY1 prole
MY PICTURE
MEMORY2
MEMORY3
MEMORY4
MEMORY1
MEMORY2
MEMORY3
MEMORY4
MEMORY8
MEMORY8
Load the prole
Custom picture
Original picture
Picture
Normalise
Picture
Normalise
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
28
Apply the MEMORY1
prole
Normal
0
0
0
0
0
Normal
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Normal
25
0
0
0
5
Normal
Picture Proles
Saving proles
Follow these steps to save picture adjustment values as proles.
Note:
When the settings are locked in “Extended life settings”, proles cannot be saved.
1
Specify the picture quality in the Picture menu and
Advanced settings. (see page 26, 27)
2
In the Picture menu, select “Memory save”.
3
5
1 select
Memory save
Memory load
Memory edit
2 access
A
N
a
n
0
!
_
Select a prole name for saving the picture adjustment
values.
1 select
Memory save
1. [
2. [
3. [
4. [
]
]
]
]
C
P
c
p
2
#
|
MEMORY1
D E F
Q R S
d e f
q r s
3 4 5
$ % &amp;
~ &lt; &gt;
Ok
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
2 set
@
.
\
;
ˆ
:
Example: Specifying “MY PICTURE”
1
Select “All delete”.
MEMORY1
All text is deleted.
To delete individual characters, select “Delete”.
Select “Ok”.
1 select
Memory save
2
Save the adjusted value in ”MEMORY1”
Ok
B
O
b
o
1
”
`
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
“” appears for a profile in which the picture
adjustments have already been saved.
4
Enter a name for the prole.
[Entering prole names]
Prole names can be up to 40 characters.
To enter text, select characters in the on-screen
keyboard.
Edit the default profile name in the text box as
desired.
Memory name input
1 select
Select “M”.
M
2 set
Repeat this process to enter the next character.
Cancel
3
Select “Y”.
MY
4
Select “Space”.
MY
6
When you nished entering the prole name, select
“Ok”.
To cancel saving the prole, select “Cancel”.
Memory name input
1 select
A
N
a
n
0
!
_
B
O
b
o
1
”
`
C
P
c
p
2
#
|
MY PICTURE
D E F G
Q R S T
d e f g
q r s t
3 4 5 6
$ % &amp; ’
~ &lt; &gt; (
Ok
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
2 set
@
.
\
;
ˆ
:
29
Picture Proles
Loading proles
Load proles and apply the picture adjustment values to the display as follows.
Notes:
• Loaded proles are stored in memory according to the selected input terminal. (see page 17)
• When the settings are locked in “Extended life settings”, proles cannot be loaded.
1
In the Picture menu, select “Memory load”.
1 select
Memory save
Memory load
Memory edit
2
Select the prole to load.
2 access
1. [
2. [
3. [
4. [
]
]
]
]
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
While in Touch Pen mode, a prole(s), whose
“Picture Mode” is set to other than “Normal”, is
grayed out and cannot be selected.
PC
When prole is being loaded,
prole name is displayed.
1 select
Memory load
16:9
Memory name: MEMORY2
NANODRIFT
Editing proles
Delete or rename proles as follows.
&lt;Deleting proles&gt;
1
2
In the Picture menu, select “Memory edit”.
1 select
Memory save
Memory load
Memory edit
1
In the Picture menu, select “Memory edit”.
Select “Memory delete”.
1 select
Memory delete
Memory name change
2
3
Select the prole to rename.
4
1. [
2. [
3. [
4. [
4
Select “Ok”.
Delete the ”MEMORY1” data.
Ok
]
]
]
]
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
Enter a name for the prole.
page 29
Entering prole names
1 select
Memory name input
1 select
Memory delete
1 select
Memory name change
2 set
MEMORY1
MEMORY2
MEMORY3
MEMORY4
All delete
2 set
Memory delete
Memory name change
Memory delete
]
]
]
]
1 select
Memory edit
1 select
1. [
2. [
3. [
4. [
2 access
Select “Memory name change”.
2 set
Select the prole to delete.
To delete all proles, select “All delete”.
1 select
Memory save
Memory load
Memory edit
2 access
Memory edit
3
&lt;Renaming proles&gt;
A
N
a
n
0
!
_
2 set
Cancel
5
B
O
b
o
1
”
`
C
P
c
p
2
#
|
EMORY1
M
D E F
Q R S
d e f
q r s
3 4 5
$ % &amp;
~ &lt; &gt;
Ok
G
T
g
t
6
’
(
H
U
h
u
7
)
I
V
i
v
8
+
[
J
W
j
w
9
–
]
K
X
k
x
L M
Y Z
l m
y z
Space
/ = ?
{
}
,
Cancel
All delete
Delete
2 set
@
.
\
;
ˆ
:
When you nished entering the prole name, select
“Ok”.
To cancel renaming the prole, select “Cancel”.
Cancel
Ok
1 select
2 set
30
Sound Adjustment
1
Normalise
2
Select to adjust each item.
Press to select the menu to adjust.
Select the desired level by listening to the sound.
3
1/2
Sound
Press to display the Sound menu.
Normal
Output Select
Sound Mode
Bass
Mid
Treble
Balance
Surround
SPEAKERS
Normal
0
0
0
0
Off
Press to exit from adjust mode.
Item
Output Select
Details
Select the audio output.
SPEAKERS: Internal speakers
AUDIO OUT: AUDIO OUT terminal output
Notes:
• If “AUDIO OUT” is selected, only “Balance” can be set. The other menus are grayed out and cannot be set.
• The audio output options will be displayed when you adjust audio volume.
30
Volume (SPEAKERS)
Sound Mode
Bass
Mid
Treble
Balance
Surround
• Audio volume and “Balance” settings are memorized separately for each audio output.
Normal: Emits the original sound.
Dynamic: Accentuates sharp sound.
Clear:
Attenuates human voice.
Adjusts low pitch sounds.
Adjusts normal sounds.
Adjusts high pitch sounds.
Adjusts left and right volumes.
Select On or Off.
Note: Bass, Mid, Treble and Surround settings are memorized separately for each Sound Mode.
Helpful Hint (
/
Normalise
Normalisation)
While the “Sound” menu is displayed, if either the N button on the remote control is pressed at any time or the
ACTION ( ) button is pressed during “Normalise”, then all adjustment values are returned to the factory settings.
SDI Sound Output
This menu is available only when selecting a slot that any of the following terminal boards is installed:
HD-SDI Terminal Board with audio (TY-FB10HD) or Dual Link HD-SDI Terminal Board (TY-FB11DHD)
SDI Sound Output
Left Channel
Right Channel
Sound Out
Level Meter
2/2
Channel 1
Channel 1
Off
Off
Item
Left Channel
Right Channel
Details
Channel 1 to Channel 16
Selects left audio channel.
Channel 1 to Channel 16
Selects right audio channel.
Sound Out
On
On:
Off:
Level Meter
Off
1-8ch
9-16ch
Sets audio channels to show in the audio level meter.
8 channels are displayed in the audio level meter; 4 channels
each on both right and left sides of the display.
Off: Hides the audio level meter.
1-8ch: Displays the audio level meter (1-8ch)
9-16ch: Displays the audio level meter (9-16ch)
Off
Enables audio output.
Disables audio output.
31
Setup menu
1
Press to display the Setup menu.
2
Press to select the menu to adjust.
3
Press to adjust the menu.
Setup
Touch-Pen Settings
Signal
Screensaver
Extended life settings
ECO Mode settings
Input label
Function Button Settings
Component/RGB-in select
No activity power off
Menu Display Duration
OSD Brightness
OSD Language
4
1/2
RGB
Disable
30 S
5
English (UK)
Press to exit from adjust mode.
Press
to return to the previous menu.
Setup menu screen
Setup
1/2
Touch-Pen Settings
Signal
Screensaver
Extended life settings
ECO Mode settings
Input label
Function Button Settings
Component/RGB-in select
No activity power off
Menu Display Duration
OSD Brightness
OSD Language
Setup
MULTI DISPLAY Setup
Portrait Setup
On/Off Timer Setup
Day/Time Setup
Network Setup
Display orientation
32
Page 34
Page 49
Page 35
Page 37
Page 40
Page 41
Page 42
RGB
Disable
30 S
5
English (UK)
Page 48
Page 43
Page 43
Page 43
Page 43
2/2
Page 44
Page 46
Page 33
Page 33
Landscape
Page 43
Network Setup
Set this to connect the Display to a computer via a network. For details
of PJLink and Network, refer to “Operating Instructions, Network
Operations”.
Day/Time Setup / On/Off Timer Setup
The timer can switch the Plasma Display On or Off.
Before attempting Timer Set, conrm the Time and adjust if necessary.
Then set POWER ON Time / POWER OFF Time.
1
2
Setup
Press to display the Setup menu.
Press to select On/Off Timer Setup or Day/Time Setup.
Press to display the On/Off Timer Setup screen or
Day/Time Setup screen.
2/2
MULTI DISPLAY Setup
Portrait Setup
On/Off Timer Setup
Day/Time Setup
Network Setup
Display orientation
Landscape
Day/Time Setup
1
2
Press to select Day or Time.
Day/Time Setup
Press to setup Day or Time.
Set
button: Forward
Day
button: Back
Time
Notes:
• Pressing “ ” or “ ” button once changes Time 1 minute.
• Pressing “ ” or “ ” button continuously changes Time by 15 minutes.
Time
MON 99:99
MON
99:99
Press to select Set.
Press to store Day/Time Setup.
Notes:
• Set cannot be selected unless Time is set.
• Unless setting the present time other than “99:99”, “Day” and “Time” cannot be set.
• The settings of “Day” and “Time” are reset when leaving the display turned off for
about 7 days for the following reasons:
Pressing
switch of the unit to turn off the display.
Disconnecting the AC cord.
Interruption of power supply.
On/Off Timer Setup
1
Press to select
On/Off Timer Setup
POWER ON Time / POWER OFF Time.
Time 99:99
Press to setup
Off
POWER ON Function
POWER ON Time / POWER OFF Time.
0:00
POWER ON Time
button: Forward
Off
POWER OFF Function
button: Back
POWER OFF Time
0:00
Notes:
• Pressing “ ” or “ ” button once changes POWER ON Time / POWER OFF Time
1 minute.
• Pressing “ ” or “ ” button continuously changes POWER ON Time / POWER OFF Time
by 15 minutes.
2
Press to select POWER ON Function/POWER OFF Function.
Press to select On.
Note: Timer function will not work unless “Time” is set.
33
Touch-Pen Settings
Set Touch Pen mode.
Select “Touch-Pen Settings” in “Setup” menu and press
button.
Touch-Pen Settings
Touch-Pen Mode
SLOT INPUT
HDMI
DVI
PC
NETWORK
Touch Only
Off
Off
Off
Off
Off
When a Terminal Board with dual input terminals is installed, “SLOT INPUT” is
displayed as “SLOT INPUT A” and “SLOT INPUT B”.
Touch-Pen Mode
Select an appropriate setting for the function of the electronic pen used.
Touch Only: Contact-type Touch Pen
Touch &amp; Remote: Contact-type Touch Pen and remote pointer
SLOT INPUT – NETWORK
Set “On” or “Off” for each input terminal.
If you switch to the input terminal that is set to “On”, the mode becomes Touch Pen
mode.
Touch-Pen On
“Touch-Pen: On” is displayed in Touch Pen mode.
Notes:
• When the following signal input, “Touch-Pen Settings” are disabled:
50i/50p/25p/24sF/24p signals and PC format signals with 50 Hz vertical frequency.
• The electronic pen cannot be used when VIDEO or COMPONENT input is selected.
• The electronic pen cannot be used during Digital Zoom. (see page 21)
• When using the electronic pen, adjust “Pos./Size” so that the screen of the computer can be correctly displayed.
(see page 23)
Setting the Remote Control
You can also turn Touch Pen mode On/Off with the FUNCTION buttons on the remote control. (see page 42)
In Touch Pen mode, the menus and functions are restricted as follows.
Pos./Size menu
Picture menu
Setup menu
Options menu
ASPECT Controls
34
Signal
Extended life settings
MULTI DISPLAY Setup
Portrait Setup
1:1 Pixel Mode: On
Over scan: Off
Picture Mode: Fixed to “Normal” (see page 26)
FRAME CREATION: Off
Picture Mode: Fixed to “Normal” (see page 37)
MULTI DISPLAY Setup: Off
Portrait Setup: Off
Display size: Unavailable
Rotate: Unavailable
16:9
Screensaver (For preventing image retention)
Do not display a still picture, especially in 4:3 mode, for any length of time.
If the display must remain on, a Screensaver should be used.
1
Select “Screensaver” in “Setup” menu and press
2
Function selection
button.
Screensaver
Time
Press to select Function.
Press to select the desired function.
Scrolling bar only
Negative image
White screen
Overlay scrolling bar
Start
Function
Mode
99:99
Scrolling bar only
Off
Negative image : Negative image will be displayed on the screen.
Scrolling bar only : A white bar will scroll from left to right. The image won't be displayed.
Overlay scrolling bar : The brightness of the image will be decreased and a white bar will scroll
on it.
White screen
: The whole screen will be white.
3
Mode selection
Press to select Mode.
Press to select each
mode items.
4
Off
Interval
: Operates when Periodic Time and Operating
Time are setup and those times arrive.
Time Designation : Operates when Start Time and Finish Time
are setup and those times arrive.
Standby after SCR Saver: Operates while Screensaver duration, and
display enters standby mode.
On
: Operates when Start is selected and the
ACTION ( ) button is pressed.
Start setting
When the Mode is set to On, press to select Start.
Press to start Screensaver.
The menu screen will disappear and the Screensaver will be activated. To stop the
Screensaver under On, press the R button or any buttons on the main unit.
Note: When the display is turned off, the Scrensaver will be deactivated.
35
Screensaver (For preventing image retention)
Setup of Screensaver Time
After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available
for selection and the Operating Time may be set. (Time cannot be set when “Mode” is “On” or “Off”.)
Press to select Start Time / Finish Time
(when Time Designation is selected).
Press to select Periodic Time / Operating Time
(when Interval is selected).
Press to select Screensaver duration
(when Standby after SCR Saver is selected).
Press to setup.
button: Forward
button: Back
Notes:
• Pressing “ ” or “ ” button once changes the Time 1 minute.
[However, switching occurs every 15 minutes when Periodic Time is selected.]
• Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.
• “Screensaver duration” of the “Standby after SCR Saver” can be set from 0:00
to 23:59. When this is set to “0:00”, “ Standby after SCR Saver” will not be
activated.
Note: Timer function will not work unless “Time” is set.
36
Screensaver
Time
Start
Function
Mode
Start Time
Finish Time
15:00
Scrolling bar only
Time Designation
6:15
12:30
Screensaver
Time
Start
Function
Mode
Periodic Time
Operating Time
15:00
Scrolling bar only
Interval
12:00
3:00
Screensaver
Time 15:00
Start
Scrolling bar only
Function
Standby after SCR Saver
Mode
6:15
Screensaver duration
Reduces screen image retention
Extended life settings
The following settings are setup to reduce image retention:
Select “Extended life settings” in “Setup” menu and press
button.
Extended life settings
Express settings
Custom settings
Reset
Set to the recommended value
Set individually
Reset to the factory settings
Extended life settings
Recommended settings
Picture Mode
Contrast
Side panel
NANODRIFT Saver
Peak limit
Lock settings
Apply to current input
Apply to all inputs
Dynamic
30
High
High mid
Off
unlock
Image Retention Reduction
Menu
Image Retention Reduction Menu
“Extended life settings” enables you to set the following 5 menus (Image Retention Reduction Menu) as recommended
values or set them individually.
Picture Mode
Contrast
“Picture Mode” and “Contrast” are same as “Picture” menu items (see page 26). The settings of this menu will be
reected to the “Picture” menu.
Note:
In “Extended life settings”, “Picture Mode” and “Contrast” of the input with Touch Pen mode On cannot be changed.
You can set “Contrast” in the “Picture” menu.
Side panel
Do not display a picture in 4:3 mode for an extended period,
as this can cause an image retention to remain on the side
panels on either side of the display eld.
To reduce the risk of such an image retention, illuminate
the side panels.
This function may be applicable to the non-picture area.
Off:
Low:
Mid:
High:
side panel
4:3 Screen
Display
image
retention
Darken both ends.
Make it dark gray.
Make it gray.
Make it light gray.
Notes:
• To reduce the occurrence of image retention, set the Side panel to High.
• The side panel may ash (alternate black/white) depending on the picture being shown on the screen. Using Cinema
mode will reduce such ashing.
37
Reduces screen image retention
NANODRIFT Saver
Moves the display position of the screen slightly to reduce image retention on the display panel.
Low–High: NANODRIFT Saver operates. The display position of the screen moves at set time intervals. You can set
the screen movement range. Some of the screen may appear to be missing as a result of this operation.
If you change the value, a mask is displayed in the range where the picture is missing as a result of
position movement.
When “NANODRIFT” Image Retention Reduction is
operating, “NANODRIFT” is displayed.
PC
16:9
NANODRIFT
Note:
This function does not work in the following cases.
When “MULTI DISPLAY Setup” is set to “On”
When “PORTRAIT Setup” is set to “On”
When in digital zoom mode
Peak limit
On: Suppresses image contrast (peak brightness).
Note: When a still picture is viewed for an extended time, the screen may become slightly darker. (see page 59)
Express settings
Set the “Image Retention Reduction” menu to the recommended settings.
All menus will be locked.
Picture Mode: Normal
Contrast: Recommended setting for each model
Side panel: High
NANODRIFT Saver: High mid
Peak limit: On
1 Select “Express settings”.
Extended life settings
Express settings
Custom settings
Reset
2 Select the input to apply the settings.
Extended life settings
Apply to current input
Apply to all inputs
3 Select “Yes”.
1 select
2 access
1 select
2 set
1 select
Extended life settings
Apply to current input
Yes
38
No
2 set
Reduces screen image retention
Custom settings
Set the individual “Image Retention Reduction” menu.
1 Select “Custom settings”.
Extended life settings
Express settings
Custom settings
Reset
1 select
2 access
set each menu to the recommended setting:
2 To
Select “Recommended settings”.
1 select
Extended life settings
Dynamic
30
High
High mid
Off
Unlock
2 set
3 Set each menu.
Recommended settings
Dynamic
30
High
High mid
Off
Unlock
2 adjust
Touch Pen mode when a menu is locked
When a menu is locked, “Touch-Pen Settings”
are disabled and Touch Pen mode cannot be set.
5 Select the input to apply the settings.
Extended life settings
Recommended settings
lock each menu setting:
4 To
Set the “Lock settings” to “Lock”.
1 select
Extended life settings
Recommended settings
Picture Mode
Contrast
Side panel
NANODRIFT Saver
Peak limit
Lock settings
Apply to current input
Apply to all inputs
Dynamic
30
0
0
0
5
Normal
Extended life settings
1 select
Extended life settings
Normal
Picture Mode
Contrast
Brightness
Colour
Hue
Sharpness
White balance
Advanced settings
Memory save
Memory load
Memory edit
Each menu will be set as same
as the “Express settings”.
Picture Mode
Contrast
Side panel
NANODRIFT Saver
Peak limit
Lock settings
Apply to current input
Apply to all inputs
Picture
Normalise
Recommended settings
Picture Mode
Contrast
Side panel
NANODRIFT Saver
Peak limit
Lock settings
Apply to current input
Apply to all inputs
When a menu is locked, it is grayed out and cannot
be set.
“Picture Mode” and “Contrast” will no longer be able
to set in the “Picture” menu, and they are labeled
with icon to indicate their locked status. Also,
“Normalise”, “Memory save” and “Memory load”
are not available.
Dynamic
30
High
High mid
Off
Lock
Picture Mode
Contrast
Side panel
NANODRIFT Saver
Peak limit
Lock settings
Apply to current input
Apply to all inputs
Dynamic
30
High
High mid
Off
Lock
1 select
2 set
2 adjust
6 Select “Yes”.
1 select
Extended life settings
Apply to current input
Yes
No
2 set
Reset
Reset the “Image Retention Reduction” menu to the factory settings. Each menu will be unlocked.
1 Select “Reset”.
Extended life settings
Express settings
Custom settings
Reset
2 Select the input to reset the settings.
Extended life settings
Reset current input
Reset all inputs
1 select
2 access
3 Select “Yes”.
1 select
Extended life settings
Reset current input
Yes
No
2 set
1 select
2 set
39
ECO Mode settings
Select “ECO Mode settings” in “Setup” menu and press
button.
ECO Mode settings
ECO Mode
Power save
Standby save
PC Power management
DVI-D Power management
No signal power off
Custom
Off
1 select
2 adjust
On
Off
Off
Disable
ECO Mode
Custom: The menu of power consumption reduction is individually set.
On: The following xed values are set to the menu of power consumption reduction. Individual setting is not available.
Power save: On
DVI-D Power management: On
Standby save: On
No signal power off: Enable
PC Power management: On
Using Remote Control
When
is pressed, the “ECO Mode” setting
ECO Mode
On
changes.
Custom settings
The menu of the power consumption reduction is individually set. This setting is enabled when “ECO Mode” is set
to “Custom”.
Power save
When this function is turned On, luminous level of the Plasma Display is suppressed, so power consumption is
reduced.
Sensor: The luminous level of the Plasma Display is automatically adjusted according to the viewing environment.
Note: In Touch Pen mode, the sensor function is disabled.
Standby save
When this function is turned On, power consumption of the microcomputer is reduced during power supply standby
(see page 15, 18, 19), so standby power of the set is reduced.
PC Power management
When this function is set to On, it operates under the following conditions to turn the power on or off automatically.
When no pictures (HD/VD sync signals) are detected for 30 or so seconds during PC signal input:
Power is turned off (standby); the power indicator lights up orange.
When pictures (HD/VD sync signals) are subsequently detected:
Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during PC signal input.
• This function is effective when “Sync” is set to “Auto”, “Component / RGB-in select” is set to “RGB” and during
normal viewing.
DVI-D Power management
When this function is set to On, it operates under the following conditions to turn the power on or off automatically.
When no pictures (sync signal) are detected for 30 or so seconds during DVI signal input:
Power is turned off (standby); the power indicator lights up orange.
When pictures (sync signal) are subsequently detected:
Power is turned on; the power indicator lights up green.
Notes:
• This function operates only during DVI signal input.
• This function is invalid during input from DVI-D Terminal Board (TY-FB11DD).
• Depending on the type of terminal board equipped, this function may be invalid.
No signal power off
Equipment power supply is turned Off when there is no signal.
When this is set to “Enable”, the power supply of the unit goes Off 10 minutes after the input signals stop.
40
Customizing the Input labels
This function can change the label of the Input signal to be displayed. (see page 17)
Select “Input label” in “Setup” menu and press
button.
Input label
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
Image input
[SLOT INPUT]*1
[VIDEO]
[COMPONENT]*2
[HDMI]
[DVI]
[PC]
[NETWORK]
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
Input label
SLOT INPUT / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 /
CATV / VCR / STB / (Skip)
VIDEO / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (Skip)
COMPONENT / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 /
CATV / VCR / STB / (Skip)
HDMI / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (Skip)
DVI / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (Skip)
PC / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 / CATV /
VCR / STB / (Skip)
NETWORK / (Skip)
(Skip): The INPUT button press will skip its input.
*1 “SLOT INPUT” is displayed when a Terminal Board is installed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”. (see page 48)
When a Terminal Board with dual input terminals is installed
“SLOT INPUT” is displayed as “SLOT INPUT A” and “SLOT INPUT B” and independent settings are available.
[SLOT INPUT A]
SLOT INPUT A / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 /
CATV / VCR / STB / (Skip)
[SLOT INPUT B]
SLOT INPUT B / DVD1 / DVD2 / DVD3 / DVD4 / Blu-ray1 / Blu-ray2 / Blu-ray3 / Blu-ray4 /
CATV / VCR / STB / (Skip)
When a Terminal Board with xed display (such as Tuner Board) is installed
Only xed display and (Skip) are available as Input label of “SLOT INPUT”.
[SLOT INPUT]
xed display / (Skip)
41
Function Button Settings
Set the functions that operates when
is pressed.
Function Button Settings
Select “Function Button Settings” in “Setup” menu and
button.
press
• Function Button 1, Function Button 2
The following functions are set to the FUNCTION button.
Function Button 1
Function Button 2
Function Button Guide
Touch-Pen
Scrolling bar
On
Note:
Factory settings are as follows.
FUNCTION1 button: Touch-Pen
FUNCTION2 button: Scrolling bar
ECO Mode settings / Signal / On/Off Timer Setup
The menu is displayed. (Example: ECO Mode settings)
ECO Mode settings
ECO Mode
Power save
Standby save
PC Power management
DVI-D Power management
No signal power off
Custom
Off
On
Off
Off
Disable
Pressing the FUNCTION button clears the menu.
Scrolling bar
Activates the “Scrolling bar only” screensaver.
After 15 minutes, the display enters standby mode.
To exit this mode, press
button.
INPUT (SLOT)* - INPUT (NETWORK)
Simply press
to select the input.
* “INPUT (SLOT)” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “INPUT (SLOT A)” and “INPUT (SLOT B)” are
displayed.
Touch-Pen
Press
and turn Touch Pen mode On/Off.
Touch-Pen
Network Setup
“Network Setup” menu is displayed.
On
Multi-Live
Switch to the Multi-Live mode when using the
“Wireless Manager”.
Computer Search
The list of connectable computers on the network is displayed.
Note:
For the network function, refer to “Operating Instructions, Network Operations” and the instruction manual of “Wireless
Manager” in use.
AV Mute
Mutes the audio and video. To exit this mode, press any button.
• Function Button Guide
The function display setting for the FUNCTION button is congured.
On: Press the FUNCTION button to display the function list of the button.
Off: The function list is not displayed.
The operation starts.
Function
1:Touch-Pen
42
2:Scrolling bar
No activity power off
Disable
Enable
When this function is set to “Enable”, the power is turned off (standby) automatically when there is no operation of
the Plasma Display for 4 hours.
Starting from 3 minutes before the turn off, the remaining time will be displayed.
Press any key to abort.
No activity power off 3min
When the power is turned off due to this function, a message “Last turn off due to ’No activity power off’.” is
displayed next time the power is turned on.
Note:
During the screensaver is running, this function is disabled.
Menu Display Duration / OSD Brightness
Set the display time and brightness of the on-screen menu display.
Menu Display Duration: 5 S - 30 S
OSD Brightness: 1 - 5
OSD Language
Select your preferred language.
Selectable languages
English(UK)
Deutsch
Fran&ccedil;ais
Italiano
Espa&ntilde;ol
ENGLISH(US)
.......(Chinese)
.......(Japanese)
.......(Russian)
Display orientation
Sets the fan control, panel drive control, and the display style of on-screen menu for vertical installation.
Landscape
Fan control and panel drive control for
horizontal installation.
Portrait
Fan control and panel drive control for vertical
installation. On-screen menu will be rotated 90
degrees counterclockwise to be suitable for the
setting.
Notes:
• If the display is installed vertically, the power switch should be located at the bottom.
• When you change this setting, fan control and panel drive control will be switched as the power is turned on next time.
43
Setup for MULTI DISPLAY
By lining up Plasma Displays in groups, for example, as illustrated below, an enlarged picture may be displayed across
all screens.
For this mode of operation, each plasma display has to be set up with a Display number to determine its location.
Note:
During Touch Pen mode, “MULTI DISPLAY Setup” becomes “Off” and this function cannot be used.
(Example)
group of 4 (2 &times; 2) group of 9 (3 &times; 3)
group of 16 (4 &times; 4)
group of 25 (5 &times; 5)
How to Setup MULTI DISPLAY
1
Select “MULTI DISPLAY Setup” in “Setup” menu and press
button.
Press to select the MULTI DISPLAY Setup.
2
MULTI DISPLAY Setup
Off
&times;2
&times;2
Off
A1
Off
MULTI DISPLAY Setup
Horizontal Scale
Vertical Scale
Seam hides video
Location
Video Wall Uniformity
Press to select “On” or “Off”.
Item
MULTI DISPLAY Setup
Details
Select “On” or “Off”.
Note: If you set MULTI DISPLAY Setup to On, Portrait Setup will be unavailable.
Horizontal Scale
Select “&times; 1”, “&times; 2”, “&times; 3”, “&times; 4”, “&times; 5”.
Vertical Scale
Select “&times; 1”, “&times; 2”, “&times; 3”, “&times; 4”, “&times; 5”.
Select “On” or “Off”.
To hide joints between displays.
To show joints between displays.
Suitable for moving image display.
Suitable for still image display.
On
Off
Seam hides video
Select the required arrangement number. (A1-E5 : Refer to the following)
Display Number locations for each arrangement.
(Examples)
( 2 &times; 1) ( 2 &times; 3 )
(4&times;2)
(4&times;4)
Location
44
(5&times;5)
A1
A2
A3
A4
A5
B1
B2
B3
B4
B5
C1
C2
C3
C4
C5
D1
D2
D3
D4
D5
E1
E2
E3
E4
E5
Setup for MULTI DISPLAY
Item
Details
Reduces the peak of brightness for each display to enable as uniform display as possible.
Select “Off” or “On”.
The brightness depends on each
display’s setting.
The brightness difference is
minimized.
Off
On
Video Wall Uniformity
Note:
If you set Video Wall Uniformity to On, the following menus will be unavailable and these
settings will be xed to the initial values.
Picture menu: Colour, Hue, Input level (Advanced settings)
ID Remote Control Function
You can set the remote control ID when you want to use this remote control on one of several different displays.
Note:
To operate this function, please purchase ID remote controller sold separately.
Object model : EUR7636070R
1
Switch
to
2
Press the
button on the remote control.
3
Press one of
-
,
for the tens digit setting.
4
Press one of
-
,
for the units digit setting.
on the right side.
Notes:
• The numbers in 2, 3 and 4 should be set up quickly.
• Adjustable ID number range is 0 - 99.
• If a number button is pressed more than two times, the rst two numbers become the ID number for the remote
control.
ID remote control button operation
The operation is the same as normal remote control except for the
button.
ID Cancellation
Press
button on remote control. (This has the same effect as pressing the
,
,
buttons at the same time.)
Notes:
• Set the Remote ID “On” to operate the ID remote control.
If Remote ID is set to “On”, you can use the remote control without identical ID number during option menu display.
(see page 53)
• The ID remote control cannot be used when ID select is set to anything other than 0, and the remote control ID is
not the same as the ID select number (see page 53).
45
Setup for Portrait
Divide an input image into 3 parts, and display one of them to a plasma display which is set vertically. The image will be enlarged
3 times and rotated 90-degree.
(Example)
Notes:
• During Touch Pen mode, “Portrait Setup” becomes “Off” and this function cannot be used.
• When using the Portrait function with displays set vertically, “Display orientation” in Setup menu has to be set to “Portrait”
(see page 43).
• Turn down the power switch for the downward direction when you set Display vertically.
How to setup Portrait
1
Select “Portrait Setup” in “Setup” menu and press
button.
Press to select the Portrait Setup.
2
Press to select “On” or “Off”.
Note:
If you set Portrait Setup to On, MULTI DISPLAY
Setup will be unavailable.
3
Press to select Seam hides video.
Press to select “Off” , “On”.
46
Portrait Setup
Portrait Setup
Seam hides video
Viewing Area
Location
Video Wall Uniformity
Portrait Setup
Portrait Setup
Seam hides video
Viewing Area
Location
Video Wall Uniformity
To hide joints between displays.
To show joints between displays.
Suitable for moving image display.
Suitable for still image display.
On
Off
Off
Off
16 : 9
1
Off
Off
Off
16 : 9
1
Off
Setup for Portrait
4
Viewing Area / Location
Viewing Area: Set a mode of image division for Portrait function.
Location:
Set a location of image to be displayed for Portrait function.
Press to select Viewing Area or Location.
Press to select each functions.
Portrait Setup
Portrait Setup
Seam hides video
Viewing Area
Location
Video Wall Uniformity
Notes:
• For HD signal videos, the “Viewing Area” is set at “16:9”,
and cannot be changed.
HD signal: 1125(1080) / 60i • 50i • 60p • 50p • 24p • 25p
• 30p • 24sF, 750(720) / 60p • 50p, 1250(1080) / 50i
• When “Viewing Area” is “16:9”, the aspect mode is set to “16:9”.
Location setting
When Portrait Setup is “On”:
Display the image of the selected location.
Off
Off
16 : 9
1
Off
When Portrait Setup is “Off”:
Represent an area of the selected Location at a normal
brightness and darken the rest of it.
Viewing Area and Location
The mode of image division and the Location by setting of Viewing Area is as follows.
Viewing Area : 16:9
Suitable to display 16:9 images. 4:3 images
extend transversely.
Both right and left sides of the image are
cut by 48 dots.
Location 1
Location 2
Undisplayed area (48 dots)
Viewing Area : 4:3
Location 1
5
Location 2
Location 3
Location 3
4:3 images are displayed without changing
aspect ratio.
Although the images of each Location
overlap, you can adjust Pos./Size to display
the image normally. (see page 23)
Video Wall Uniformity
Reduces the peak of brightness for each display to enable as uniform display as possible.
Press to select Video Wall Uniformity
Press to select “Off” , “On”.
The brightness depends
The brightness
on each display’s setting. difference is minimized.
Portrait Setup
Portrait Setup
Seam hides video
Viewing Area
Location
Video Wall Uniformity
Off
Off
16 : 9
1
Off
Off
On
Note:
If you set Video Wall Uniformity to On, the following menus will be unavailable and these settings will be xed to the
initial values.
Picture menu: Colour, Hue, Input level (Advanced settings)
47
Setup for Input Signals
Component / RGB-in select
Component
RGB
Select to match the signals from the source connected to the Component / RGB or PC input terminals.
“Component”
Y, PB, PR signals
“RGB”
RGB signals
Note:
Make setting of the selected input terminal (COMPONENT/RGB IN or PC IN).
YUV / RGB-in select
YUV
RGB
Select to match the signals from the source connected to the DVI input terminals.
YUV signals
“YUV”
“RGB”
RGB signals
Notes:
• Selection may not be possible, depending on which optional board is installed.
• Make setting of the selected input terminal (SLOT or DVI-D IN).
48
Setup for Input Signals
Signal menu
Notes:
• “Signal” setup menu displays a different setting condition for each input signal.
• Depending on the input signal type, an optional Terminal Board may be required.
button.
Select “Signal” in “Setup” menu and press
For Video (S VIDEO)
For RGB
[ AV ]
Signal
FRAME CREATION
Colour system
Cinema reality
Noise reduction
[ RGB ]
Signal
H-Freq.
V-Freq.
Signal Format
For Component
[ Component ]
Signal
Mid
Auto
Off
Auto
Off
FRAME CREATION
Sync
Cinema reality
XGA Mode
Noise reduction
Mid
Auto
Off
Off
63.98 kHz
60.02 Hz
1280&times;1024/60i
For Digital
[ Digital ]
Signal
FRAME CREATION
Sync
Cinema reality
XGA Mode
Noise reduction
H-Freq.
V-Freq.
Signal Format
Mid
Auto
Off
Auto
Off
FRAME CREATION
Cinema reality
Mid
Off
HDMI Range
Noise reduction
Auto
Off
H-Freq.
63.98 kHz
60.02 Hz
1280&times;1024/60i
63.98
kHz
V-Freq. 60.02 Hz
Signal Format 1280&times;1024/60i
• 3D Y/C Filter (NTSC)
This menu is displayed when BNC Dual Video Terminal Board (TY-FB9BD) is installed to the unit.
Set this menu when the moving image looks unnatural during Video (S Video) input signal.
Off
On
Note:
When On, this setting only affects NTSC input signals.
• Colour system
Auto
PAL
SECAM
M.NTSC
NTSC
Set the colour system to match the input signal. When “Auto” is set, Colour system will be automatically selected
from NTSC/PAL/SECAM/M.NTSC.
To display PAL60 signal, select “Auto” or “PAL”.
If the picture image becomes unstable:
With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases
become unstable. Should this occur, set the system to match the format of the input signal.
• Cinema reality
When “On”, the display attempts to reproduce a more natural interpretation of sources such as movie pictures,
which are recorded at 24 frames per second.
If the picture is not stable, turn the setting to “Off”.
Off
On
Note:
When On, this setting only affects the following signal input:
• NTSC / PAL signal input during Video (S Video) input signal.
• 525i(480i), 625i(575i), 1125(1080)/60i signal input during “Component” input signal.
• XGA Mode
This menu is displayed when the input signal is analog (Component/PC). This unit supports three types of XGA
signals with 60Hz vertical frequency having different aspect ratios and sampling rates (1,024 &times; 768 @ 60Hz,
1,280 &times; 768 @ 60Hz and 1,366 &times; 768 @ 60Hz).
Auto
1024&times;768
1280&times;768
1366&times;768
Auto: Automatically selected from 1024&times;768/1280&times;768/1366&times;768.
Switch the setting to suit the input signal for better display depends on the angle of view or display
resolution condition.
Note:
After making this setting, be sure to make each adjustment (such as “Auto Setup”) on the “Pos./Size” menu as
necessary. (see page 23)
49
Setup for Input Signals
• Sync
This function operates only during input from PC IN terminal.
Setting RGB sync signal
Conrm that the input is set to RGB input (this setting is valid only for RGB input signal).
Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
on G: Uses a synchronized signal on the Video G signal, which is input from the G connector.
Setting Component sync signal
Conrm that the input is set to Component input (this setting is valid only for Component input signal).
Auto: The H and V sync or synchronized signal is automatically selected. If both input, it is selected the H and V sync.
on Y: Uses a synchronized signal on the Video Y signal, which is input from the Y connector.
Note:
Signals input to COMPONENT/RGB IN terminals correspond to Sync on G or Sync on Y.
• SDI Through
Set the active through function of the Dual Link HD-SDI Terminal Board (TY-FB11DHD).
On
Off
On: Enables active through.
Off: Disables active through.
Note:
Settings can only be performed for this menu when a slot mounted with a Dual Link HD-SDI Terminal Board
(TY-FB11DHD) is selected.
• FRAME CREATION
Automatically compensates the picture frame rate and removes juddering movements to make the images
smooth.
Off
Mid
Max
Note:
Depending on the contents, images may be noisy. To prevent the noise, change the setting.
• HDMI Range
Switches the dynamic range according to the input signal from HDMI terminal.
Full(0-255)
Auto
Video(16-235)
Video(16-235): If the input signal is the video range, Example: HDMI terminal output for DVD player
Full(0-255): If the input signal is full range, Example: HDMI terminal output for personal computer
Auto: Switches the dynamic range automatically between “Video(16-235)” and “Full(0-255)” according to the input signal.
Note:
This function can be set only for HDMI signal input.
50
Setup for Input Signals
• Noise reduction
Sets the following three NR (Noise Reduction) functions together.
P-NR, Mosquito NR, Block NR
(
Press to select “Noise reduction”.
)
Noise reduction
Off
Press to select “Off”, “Min” , “Mid” , “Max” , “Advanced”.
Advanced NR
Sets the three NR functions separately.
1
Noise reduction
Press to select “Advanced”.
Press to enter Advanced NR.
Press to select P-NR, Mosquito
NR or Block NR.
Press to select “Off”, “Min”, “Mid”,
“Max”.
[ AV ]
Advanced NR
P-NR
Mosquito NR
Block NR
2
Advanced
Advanced NR
P-NR
Mosquito NR
Block NR
P-NR
Mosquito NR
Block NR
Off
Off
Off
[ Component ]
Off
Off
Off
[ RGB ]
Advanced NR
Off
Off
Off
[ Digital ]
Advanced NR
P-NR
Mosquito NR
Block NR
Off
Off
Off
P-NR:
Automatically reduces unwanted picture noise.
Mosquito NR: Reduces mosquito noise around subtitles on MPEG videos.
Block NR: Reduces block noise when playing MPEG videos.
Note:
Noise reduction cannot be adjusted while a PC signal is being applied.
• Input signal display
Displays the frequency and the type of the current input signal.
This display is valid only for Component / RGB / PC and Digital input signal.
Display range:
Horizontal 15 - 110 kHz
Vertical
48 - 120 Hz
The dot clock frequency is displayed during DVI signal input.
H-Freq.
V-Freq.
Signal Format
H-Freq.
63.98 kHz
60.02 Hz
1280&times;1024/60i
63.98
kHz
V-Freq. 60.02 Hz
Dot Clock Freq. 108.0 MHz
Signal Format 1280&times;1024/60i
51
Options Adjustments
Options
1
Weekly Command Timer
Audio input select
Input Search
Press to display the Setup menu.
Press to select “OSD Language”.
2
Onscreen display
Initial input
Initial VOL level
Maximum VOL level
Input lock
Button lock
Remocon User level
Press for more than 3 seconds.
Press to select “Options”.
3
Options
Shipping
Press to display the Options menu.
Press to select your preferred menu.
4
Off
0
Off
0
Off
Off
Off
2/3
Off-timer function
Enable
Initial Power Mode
ID select
Remote ID
Serial ID
Display size
Studio W/B
Studio Gain
Normal
0
Off
Off
Off
Off
Off
3/3
Off
Slot power
Off
Power On Screen Delay
Clock Display
Off
All Aspect
Off
Auto Setup
Manual
Rotate
Off
Advanced Motion Resolution
On
Power On Message (No activity power off)
On
Press to exit from Options menu.
Item
On
Off
Options
Options
Press to adjust the menu.
5
1/3
Adjustments
Weekly Command Timer Sets Weekly Command Timer. (see page 55)
Audio input select Set up the sound when an image input is selected. (see page 57)
Input Search
Set auto input switching for when there is no signal. (see page 58)
On: Displays all the following on screen.
• Power on display
• Input signal switch display
Onscreen display
• No signal display
was pressed.
• Mute and the remaining time of off-timer after
Off: Hides all the items above from view.
Adjusts the input signal when the unit is turned on.
SLOT INPUT*1
VIDEO
COMPONENT*2
HDMI
DVI
PC
NETWORK
Off
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
Initial input
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”. (see page 48)
Notes:
• Only the adjusted signal is displayed. (see page 17)
• This menu is available only when “Input lock” is “Off”.
Press
Initial VOL level
Press
Maximum VOL level
52
button to adjust the volume when the unit is turned on.
On
Off
Off: Sets normal volume.
On: Sets your preferred volume.
Notes:
• When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
• You can hear the changed volume regardless of your volume setting before opening the options menu
if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
button to adjust the maximum volume.
On
Off
Off: Sets auto maximum volume.
On: Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically
becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• You can hear the changed volume regardless of your volume setting before opening the options menu
if you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
Options Adjustments
Item
Adjustments
Input lock
Locks the input switch operation.
Off
SLOT INPUT*1
VIDEO
COMPONENT*2
HDMI
DVI
PC
NETWORK
*1 “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B”
are displayed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”.
(see page 48)
Notes:
• Only the adjusted signal is displayed (see page 17).
• Input switch can be used when this is set to “Off”.
MENU&amp;ENTER
On
Off
Off: All the buttons on main unit can be used.
MENU&amp;ENTER: Locks
Button lock
Remocon User level
MENU
and
ENTER/
buttons on main unit.
On: Locks all the button on main unit.
Sets Button lock with the unit buttons in the following procedure.
ENTER/
INPUT four timesPress
- / four timesPress
+ / four timesPress
Off: Press
ENTER/
INPUT four timesPress
+ / four timesPress
MENU&amp;ENTER: Press
four timesPress
ENTER/
ENTER/ four timesPress
- / four timesPress
+ / four timesPress
On: Press
ENTER/
User1
User2
User3
Off
Off: You can use all of the buttons on the remote control.
, , , ,
buttons on the remote control.
User1: You can only use
button on the remote control.
User2: You can only use
User3: Locks all the buttons on remote control.
Off-timer function
Enable: Enables the “Off-timer function”.
Disable: Disables the “Off-timer function”.
Note: When “Disable” is set, the Off-timer is cancelled.
Initial Power Mode
Normal
Standby
On
Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.
Normal: Power returns in as the same state as before the power interruption.
Standby: Power returns in standby mode. (Power Indicator : red/orange)
On:
Power returns in power On. (Power Indicator : green)
Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.
ID select
Remote ID
Serial ID
Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
The setting of this menu is valid only when using ID remote control.
Off: Disables ID remote control functions. You can use normal remote control operations.
On: Enable ID remote control functions.
Note: To use the ID remote control function, it is necessary to set each ID number of remote control and display unit.
About the setting method, please refer to “ID Remote Control Function” (see page 45) and “ID
select” (above-mentioned).
Sets the panel ID Control.
Off: Disables external control by the ID.
On: Enables the external control by the ID.
Adjusts the image display size on screen.
Off: Sets the normal image display size on screen.
On: Sets the image display size approximately 95 % of the normal image display.
Off
On
Display size
Notes:
• This setting is valid only when the input signals are as follows;
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (Video)
525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p,
1125/30p, 1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when digital zoom, Multi display or Portrait display is selected.
• When “Display size” is set to “On”, “H-Pos” and “V-Pos” in “Pos./Size” can be adjusted.
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
53
Options Adjustments
Item
Adjustments
Studio W/B
Off: Nullify all the settings adjusted.
On: Sets the colour temperature for TV studio.
Note: Valid only when the “Warm” is set as “White balance” in Picture menu.
Studio Gain
Sharpens the contrast for a better view when a part of the image is too light to see.
Off: Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note: This setting is valid only when the input signals are as follows:
Component Video, RGB (analog), SDI, HDMI
Slot power
Auto
On
Off
Off: Power is not transmitted to the slot power.
Auto: Power is transmitted to the slot power only when main power is on.
On: Power is transmitted to the slot power when main power is on or in the standby state.
Note: In some cases, power is transmitted to the slot power when main power is on or in the standby
state regardless of the slot power setting.
Power On Screen
Delay
Off
1
2
3....
30
You can set the power-on delay time of the displays to reduce the power load, when you press
to
turn on the multiple displays that are set together, for example, on MULTI DISPLAY system.
Set each display’s setting individually.
is pressed.
Off:
The display will be turned on at the same time as
1 to 30 (sec.): Set the power-on delay time (second).
, the display will be powered on with time delay depending on this
After pressing
setting.
Notes:
• During this function is working, the power indicator is blinking green.
• This function also works when the power recovers from failure or after plugging off and in again the
power cord.
After you unplug and plug the power cord in while the unit is in standby mode and also the power is
being supplied to a terminal board, the unit will start supplying the power to the board with time delay
according to the setting.
The power indicator lights up red rst and it turns orange when the power starts being supplied to the
board.
Off: Not display the clock.
On: Display the clock.
The clock is displayed at the lower left of the screen when
Clock Display
button is pressed.
Note: When “Day/Time Setup” is not set, the clock is not displayed even if “Clock
Display” is “On”. (see page 33)
10:00
All Aspect
Sets All Aspect mode (advanced aspect setting) or default aspect mode.
button, the aspect changes in the selected mode.
With each press of
Off: Default aspect mode
On: All Aspect mode
Aspect mode of each setting is as follows:
(Example: HD signal)
Off 4:34:3 FullZoom1Zoom2Zoom316:914:9Just
On 4:3 (1)4:3 (2)4:3 FullZoom1Zoom2Zoom316:914:9Just1Just2
Auto Setup
Sets the operational mode of the automatic position adjustment in the Pos./Size menu.
is pressed on the remote control or automatic
Manual: Automatic position adjustment starts when
position adjustment is executed from the Pos./Size menu.
Auto: Other than remote control or menu operation, automatic position adjustment starts:
When the display power is turned ON.
When the input signal is switched.
Rotate
Advanced Motion
Resolution
Power On Message
(No activity power
off)
54
Off: Does not rotate the image.
On: Rotates the image 180 degrees.
Displays motion picture images at higher resolution.
Off
On
Note: Please set to “Off” if images look unnatural.
Whether to show/hide No activity power off Precautions at the time of power ON is set.
On: The warning precautions are shown at the time of power ON.
Off: The warning precautions are not shown at the time of power ON.
Note: This setting is enabled only if “No activity power off” is “Enable” (see page 43).
Options Adjustments
Normalisation
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or
“Remote ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
- / button on main unit together with
button on the remote control and hold for more than 5 seconds.
Press the
The “Shipping” menu is displayed and the lock is released when it disappears.
Weekly Command Timer
You can set 7-day timer programming by setting time and command.
Note:
Before setting Weekly Command Timer, set Day/Time Setup. (see page 33)
1
Press to select Function.
Press to select “On”.
Note:
• When Function is set to On, On/Off Timer
Setup (see page 33) is unavailable and
Interval / Time Designation in Mode of
Screensaver (see page 35) cannot be
selected.
2
Weekly Command Timer
Audio input select
Input Search
On
Onscreen display
Press ACTION ( ) button
Weekly Command Timer
On
Press to select a day.
Monday
Tuesday
Program1
Press to select a program number.
Wednesday
Thursday
Friday
Saturday
Sunday
Program Edit
Press to select Program Edit.
Press to show the Program Edit screen.
4
1/3
Function
Note:
• You can set the program from 1 to 7.
--- indicates unset.
3
Options
Press to select Program.
Press to change the program numbers (1-7).
Program3
--Program3
--Program6
Program4
y Program number
Program3
Thursday
--Friday
Program6
Saturday
Program4
Sunday
Program Edit
Program Edit screen
1/8
Weekly Command Timer
Program
8:00
01
10:30
02
--:-03
--:-04
--:-05
12:00
06
9:12
07
--:-08
1
PON
IMS:SL1
------DAM:ZOOM
AVL:10
---
55
Options Adjustments
Press to select a command number.
5
Press to show the previous / next command
pages (1-8) of the selected program.
Press to show the command setting screen.
1/8
Weekly Command Timer
Program
01
02
03
04
05
06
07
08
1
8:00
10:30
PON
IMS:SL1
--:--
---
--:--
---
--:--
---
12:00
9:12
--:--
DAM:ZOOM
AVL:10
---
8/8
Weekly Command Timer
Program
57
58
59
60
61
62
63
64
1
20:00
AVL:00
20:30
22:00
DAM:NORM
POF
--:--
---
--:--
---
--:--
---
--:--
---
--:--
---
Command (--- indicates unset)
Set time of timer(--:-- indicates unset)
Command numbers
6
Press to select Command No.
Press to select a command number.
Command setting screen
Weekly Command Timer
Program
1
Command No
Time
Command
7
Press to select Time / Command.
02
10:30
IMS:SL1
Weekly Command Timer
1
Program
Press to set each item.
02
Command No
Time: Set the time to execute a command program.
10:30
Time
IMS:SL1
Command
Pressing “ ” or “ ” button once changes “Time” 1
minute.
Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command: Select a command to execute at the set time. This unit has 64 commands to set.
(see page 63)
Notes:
• Command is performed in order of execution time, regardless of the command number.
• If a command execution time overlaps with that of other commands, these commands are
performed in number order.
• Pressing , Time becomes --:-- and Command becomes ---.
Note:
Press
56
to return to the previous screen.
Options Adjustments
Audio input select
Set up the sound when an image input is selected.
Options
1/3
Weekly Command Timer
Audio input select
Input Search
Onscreen display
On
Press ACTION ( ) button
Audio input select
Press to select image input.
Press to select audio input.
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
SLOT INPUT
VIDEO/COMPONENT
VIDEO/COMPONENT
HDMI
DVI/PC
DVI/PC
NETWORK
Image input
[SLOT INPUT]*1
[VIDEO]
[COMPONENT]*2
[HDMI]
[DVI]
[PC]
[NETWORK]
Audio input
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / HDMI / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
VIDEO/COMPONENT: Sound input for both VIDEO and COMPONENT.
DVI/PC: Sound input for both DVI and PC.
NO AUDIO: No audio input (Mute)
*1 “SLOT INPUT” is displayed when a Terminal Board is installed.
*2 “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”.
(see page 48)
When a Terminal Board with dual input terminals is installed
“SLOT INPUT” is displayed as “SLOT INPUT A” and “SLOT INPUT B” and independent settings are available.
To set other image inputs, you can select “SLOT INPUT A” and “SLOT INPUT B”.
Image input
Audio input
[SLOT INPUT A]
[SLOT INPUT B]
[VIDEO]
[COMPONENT]
[HDMI]
[DVI]
[PC]
[NETWORK]
SLOT INPUT A / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / HDMI / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
SLOT INPUT A / SLOT INPUT B / VIDEO/COMPONENT / DVI/PC / NETWORK / NO AUDIO
When Image input and Audio input differ from each other, the Audio input is displayed as below.
PC
16:9
COMPONENT
NANODRIFT
Notes:
• HDMI Audio is selectable only for HDMI Input.
• You cannot set audio of B for SLOT INPUT A, or audio of A for SLOT INPUT B.
• If a tuner board is equipped to SLOT, the audio of SLOT INPUT (tuner board) cannot be output with the image input
other than SLOT INPUT.
57
Options Adjustments
Input Search
When a signal is not detected, another input with a signal is automatically selected.
Options
1/3
Weekly Command Timer
Audio input select
Input Search
Press ACTION ( ) button
1 select
Input Search
2 adjust
Input Search
Primary Input
Secondary Input
Off
Input Search
Off: When there is no signal, the input is not switched automatically.
All Inputs: Searches all inputs and switches to an input with a signal.
Input search is executed in the following order.
(Example) When the current input is PC
PC
NETWORK
SLOT INPUT
VIDEO
COMPONENT
HDMI
DVI
Priority: Searches “Primary Input” and “Secondary Input” in order and switches to an input with a signal.
Searching...
“Searching...” is displayed during the input search.
Primary Input, Secondary Input
Set the input to search when “Priority” is selected.
(NONE)
SLOT INPUT*
VIDEO
COMPONENT
HDMI
DVI
PC
NETWORK
* “SLOT INPUT” is displayed when an optional Terminal Board is installed.
When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.
Notes:
• This menu is available only when “Input lock” is “Off”. (see page 53)
• If the input is changed by this function, the last input is selected when the power is turned on next time.
If you wish to retain the original input when the power is turned on, set “Initial input” to the original input.
(see page 52)
58
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Sound
Interference
Noisy Sound
Normal Picture
No Sound
Checks
Electrical Appliances
Cars / Motorcycles
Fluorescent light
Volume
(Check whether the mute function has been activated on the remote control.)
Check if speakers are connected properly.
No Picture
No Sound
No Picture
Normal Sound
Not plugged into AC outlet
Not switched on
Picture and Brightness/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
If a signal with a non-applicable colour system format, or frequency is input, only
the input terminal indication is displayed.
No Colour
Normal Sound
Colour controls set at minimum level (see page 26, 27)
Colour system (see page 49)
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where
the image is missing appear when I use the zoom
function.
I can hear sounds coming from inside the unit.
Check whether the batteries have discharged completely and, if they have not,
whether they were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a
strong uorescent light.
Check whether the remote control designed specically for use with the unit is
being used. (The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet
undergoing very slight contractions in response to changes in the room temperature.
There are no adverse effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a
screen wider than one in the 16:9 mode, blank areas separate from the images
are formed at the top and bottom of the screen.
When the power is turned on, a sound of the display panel being driven may be
heard: This is normal and not indicative of malfunctioning.
Parts of the unit become hot.
Even when the temperature of parts of the front, top and rear panels has risen, these
temperature rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly.
Check the settings of “PC Power management”, “DVI-D Power management”,
“No signal power off” and “No activity power off” in the Setup menu. Any of them
may be set to “On (Enable)”. (see page 40, 43)
Power indicator is blinking in red.
There is possibility of malfunction. Please contact an Authorized Service Center.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the
type of input signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
The screen darkens slightly
when bright pictures with minimal
movements are shown.
It takes a while for the picture
to appear.
The edges of the images
icker.
The brightness on both sides of
images in the 4:3 mode changes.
Some parts of the screen do
not light up.
Image retention appears
Whirring sounds can be heard
from the display unit.
Check
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
The unit digitally processes the various signals in order to reproduce esthetically pleasing images. As
such, it sometimes takes a few moments for the picture to appear when the power has been turned
on, when the input has been switched.
Due to the characteristics of the system used to drive the panel, the edges may appear to icker in
the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
When viewing the side panels at the “High” or “Mid” setting, the brightness on both sides may change
depending on the kind of program shown: This is normal and not indicative of malfunctioning.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images displayed
in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from xed image use is not an
operating defect and as such is not covered by the Warranty.
This product is not designed to display xed images for extended periods of time.
The display unit is tted with a cooling fan to dissipate heat generated during normal use. The whirring
sound is caused by rotation of the fan and is not a malfunction.
59
List of Aspect Modes
Aspect mode
All Aspect: Factory setting
On
All Aspect: Off
16:9
14:9
16:9
Enlarged screen
Description
The display of the pictures lls the screen.
In the case of SD signals, pictures with a 4:3 aspect
ratio are enlarged horizontally, and displayed. This
mode is suited to displaying anamorphic pictures with
a 16:9 aspect ratio.
14:9
Letterbox pictures with a 14:9 aspect ratio are enlarged
vertically and horizontally so that their display lls the
screen vertically and is slightly smaller than the screen
horizontally. The top and bottom edges of the pictures
are cut off. Side panels are displayed at the left and right
edges of the screen.
Just
Pictures with a 4:3 aspect ratio are enlarged horizontally
so that the picture distortion is minimized. The display of
the areas around the left and right edges of the screen
is slightly elongated.
–
The pictures with a 4:3 aspect ratio among the 16:9 aspect
ratio signals are enlarged horizontally so that the picture
distortion is minimized. The left and right edges of the
pictures are cut off. The display of the areas around the
left and right edges of the screen is slightly elongated.
Just
Just1
Just2
Picture
4:3
4:3
Pictures with a 4:3 aspect ratio are displayed with their
original aspect ratio. Side panels are displayed at the
left and right edges of the screen.
4:3 (1)
4:3 (2)
4:3 Full
–
The pictures with a 4:3 aspect ratio among the 16:9
aspect ratio signals are displayed with their original
aspect ratio. The left and right edges of the pictures are
masked with side panels.
4:3 Full
The pictures with a 4:3 aspect ratio among the 16:9
aspect ratio signals are enlarged horizontally so that
their display lls the screen. The left and right edges of
the pictures are cut off.
Zoom1
Letterbox pictures with a 16:9 aspect ratio are enlarged
vertically and horizontally so that their display lls the
screen. The top and bottom edges of the pictures are
cut off.
Zoom2
The letterbox pictures with a 2.35:1 aspect ratio among
the 16:9 aspect ratio signals are enlarged vertically and
horizontally so that their display lls the screen. The top
and bottom edges as well as the left and right edges of
the pictures are cut off.
Zoom3
Letterbox pictures with a 2.35:1 aspect ratio are enlarged
vertically and horizontally so that their display lls the
screen vertically and is slightly larger than the screen
horizontally. The top and bottom edges as well as the
left and right edges of the pictures are cut off.
Zoom
Zoom1
Zoom2
Zoom3
60
Applicable Input Signals
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Signal name
Horizontal frequency
(kHz)
Vertical frequency
(Hz)
525 (480) / 60i
525 (480) / 60p
625 (575) / 50i
625 (576) / 50i
625 (575) / 50p
625 (576) / 50p
750 (720) / 60p
750 (720) / 50p
1,125 (1,080) / 60p
1,125 (1,080) / 60i
1,125 (1,080) / 50p
1,125 (1,080) / 50i
1,125 (1,080) / 24sF
1,125 (1,080) / 30p
1,125 (1,080) / 25p
1,125 (1,080) / 24p
1,250 (1,080) / 50i
2,048 &times; 1,080 / 24sF 7
2,048 &times; 1,080 / 24p 7
640 &times; 400 @70 Hz
640 &times; 480 @60 Hz
640 &times; 480 @72 Hz
640 &times; 480 @75 Hz
640 &times; 480 @85 Hz
800 &times; 600 @56 Hz
800 &times; 600 @60 Hz
800 &times; 600 @72 Hz
800 &times; 600 @75 Hz
800 &times; 600 @85 Hz
852 &times; 480 @60 Hz
1,024 &times; 768 @50 Hz
1,024 &times; 768 @60 Hz
1,024 &times; 768 @70 Hz
1,024 &times; 768 @75 Hz
1,024 &times; 768 @85 Hz
1,066 &times; 600 @60 Hz
1,152 &times; 864 @60 Hz
1,152 &times; 864 @75 Hz
1,280 &times; 768 @60 Hz
1,280 &times; 800 @60 Hz (1)
1,280 &times; 800 @60 Hz (2)
1,280 &times; 960 @60 Hz
1,280 &times; 960 @85 Hz
1,280 &times; 1,024 @60 Hz
1,280 &times; 1,024 @75 Hz
1,280 &times; 1,024 @85 Hz
1,366 &times; 768 @50 Hz
1,366 &times; 768 @60 Hz
1,400 &times; 1,050 @60 Hz
1,440 &times; 900 @60 Hz (1)
1,440 &times; 900 @60 Hz (2)
1,600 &times; 1,200 @60 Hz
1,600 &times; 1,200 @65 Hz
1,920 &times; 1,080 @60 Hz
1,920 &times; 1,200 @60 Hz
Macintosh13” (640 &times; 480)
Macintosh16” (832 &times; 624)
Macintosh21” (1,152 &times; 870)
15.73
31.47
15.63
15.63
31.25
31.25
45.00
37.50
67.50
33.75
56.26
28.13
27.00
33.75
28.13
27.00
31.25
27.00
27.00
31.46
31.47
37.86
37.50
43.27
35.16
37.88
48.08
46.88
53.67
31.47
39.55
48.36
56.48
60.02
68.68
37.64
53.70
67.50
47.70
49.31
49.70
60.00
85.94
63.98
79.98
91.15
39.55
48.36
65.22
55.47
55.93
75.00
81.25
67.50
74.04
35.00
49.72
68.68
59.94
59.94
50.00
50.00
50.00
50.00
60.00
50.00
60.00
60.00
50.00
50.00
48.00
30.00
25.00
24.00
50.00
48.00
24.00
70.07
59.94
72.81
75.00
85.01
56.25
60.32
72.19
75.00
85.06
59.94
50.00
60.00
70.07
75.03
85.00
59.94
60.00
75.00
60.00
59.91
59.81
60.00
85.00
60.02
75.03
85.02
50.00
60.00
60.00
59.90
59.89
60.00
65.00
60.00
59.95
66.67
74.54
75.06
*Mark: Applicable input signal
DVI-D IN
COMPONENT / RGB
(Dot clock
HDMI
IN / PC IN
(MHz))
(Dot clock (MHz))
* (13.5)
* (27.0)
*
* (27.0) 5
* (27.0)
*
* (13.5)
* (27.0)
*
* (27.0)
* (27.0)
*
* (74.25)
* (74.25)
*
* (74.25)
* (74.25)
*
* (148.5) 1
* (148.5)
*
* (74.25)
*
* (74.25) 1
* (148.5) 1
* (148.5)
*
* (74.25)
*
* (74.25) 1
* (74.25) 2
* (74.25)
* (74.25) 1
* (74.25)
* (74.25) 1
* (74.25)
*
* (74.25) 1
* (74.25) 3
*
*
*
*
*
*
*
*
*
*
*
(25.17)
(25.18)
(31.5)
(31.5)
(36.0)
(36.0)
(40.0)
(50.0)
(49.5)
(56.25)
(33.54)
*
*
*
*
*
(65.0)
(75.0)
(78.75)
(94.5)
(53.0)
*
*
*
*
*
*
*
*
*
(108.0)
(80.14)
(71.0)
(83.5)
(108.0)
(148.5)
(108.0)
(135.0)
(157.5)
6
6
* (86.71)
*
*
*
*
*
(88.75)
(106.5)
(162.0)
(175.5)
(148.5)
4
* (25.18)
*
* (40.0)
*
* (34.24)
* (51.89)
* (65.0)
*
*
*
* (53.0)
* (81.62)
*
*
* (71.0)
* (83.5)
*
*
* (108.0)
*
*
*
*
*
*
*
*
*
*
*
*
*
(69.92)
(87.44)
(122.61)
(88.75)
(106.5)
(162.0)
* (148.5)
* (154.0)
*
*
* (30.24)
* (57.28)
* (100.0)
1: Based on SMPTE 274M standard.
2: Based on SMPTE RP211 standard.
3: Based on SMPTE 295M standard.
4: The input signal is recognized as 1,125 (1,080) / 60p.
5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60Hz signal.
6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal
Board (TY-FB11DHD) is installed.
Note: Signals without above specication may not be displayed properly.
61
Applicable Input Signals
Video input (VIDEO)
Signal name
1
2
3
4
5
NTSC
PAL
PAL60
SECAM
Modied NTSC
Horizontal
frequency(kHz)
15.73
15.63
15.73
15.63
15.73
Vertical
frequency(Hz)
59.94
50.00
59.94
50.00
59.94
Shipping condition
This function allows you to reset the unit to the factory setting.
1
2
Setup
Press to display the Setup menu.
Press to select “OSD Language”.
1/2
Touch-Pen Settings
Signal
Screensaver
Extended life settings
ECO Mode settings
Input label
Function Button Settings
Component/RGB-in select
Press for more than 3 seconds.
3
RGB
Disable
30 S
5
English (UK)
No activity power off
Menu Display Duration
OSD Brightness
OSD Language
Press to select “Shipping”.
Options
Shipping
Press to display the Shipping menu.
4
Press to select “YES”.
Shipping
YES
Press to conrm.
5
Wait for 10 seconds.
6
Press the power switch (
) on main unit to turn the power off.
[from the unit]
1 Press the MENU button till the Setup menu is displayed.
2 Press the Volume Up“+” or Down“–” button to select “OSD Language”.
3 Press and hold the ENTER button till the Shipping menu is displayed.
4 Press the Volume Up“+” or Down“–” button to select “YES”.
5 Press the ENTER button and wait for 10 sec.
) on main unit to turn the power off.
6 Press the power switch (
62
NO
Command list of Weekly Command Timer
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Command
AAC:MENCLR
AAC:MENDYN
AAC:MENSTD
AAC:SURMON
AAC:SUROFF
AMT:0
AMT:1
AVL:00
AVL:10
AVL:20
AVL:30
AVL:40
AVL:50
AVL:60
DAM:FULL
DAM:JUST
DAM:NORM
DAM:ZOOM
IMS:SL1
IMS:S1A
IMS:S1B
IMS:VD1
IMS:YP1
IMS:HM1
IMS:DV1
IMS:PC1
IMS:NW1
OSP:SCR0
OSP:SCR1
POF
PON
SSC:FNC0
SSC:FNC1
SSC:MOD0
SSC:MOD3
VMT:0
VMT:1
Control details
Audio Menu (Clear)
Audio Menu (Dynamic)
Audio Menu (Standard)
Surround (ON)
Surround (OFF)
Audio Mute (OFF)
Audio Mute (ON)
Audio Volume (00)
Audio Volume (10)
Audio Volume (20)
Audio Volume (30)
Audio Volume (40)
Audio Volume (50)
Audio Volume (60)
Aspect (16:9)
Aspect (Just)
Aspect (4:3)
Aspect (Zoom)
Input select (SLOT INPUT)
Input select (SLOT INPUT A)
Input select (SLOT INPUT B)
Input select (VIDEO)
Input select (COMPONENT)
Input select (HDMI)
Input select (DVI)
Input select (PC)
Input select (NETWORK)
Screen Saver Scrolling bar only (OFF)
Screen Saver Scrolling bar only (ON)
Power OFF
Power ON
Screen Saver function (Scrolling bar only)
Screen Saver function (Negative image)
Screen Saver (Mode (OFF))
Screen Saver (Mode (ON))
Picture Mute (OFF)
Picture Mute (ON)
Picture Mute cannot be unlocked
by powering off/on with the remote
control. Turn off and on again with
the button on the unit or enter the
command VMT:0 to unlock Picture
Mute.
63
Specications
TH-85PB1W
Power Source
Power Consumption
Power on
Stand-by condition
Power off condition
Plasma Display panel
Screen size
(No.of pixels)
Operating condition
Temperature
Humidity
Applicable signals
Colour System
Scanning format
PC signals
Connection terminals
AV IN
VIDEO
AUDIO L-R
HDMI
COMPONENT/RGB IN
Y/G
PB/CB/B
PR/CR/R
AUDIO L-R
DVI-D IN
AUDIO
PC IN
AUDIO
SERIAL
WIRELESS MODULE
LAN
AUDIO
L-R
OUT
Sound
Speakers
Audio Output
Dimensions (W &times; H &times; D)
Mass (weight)
TH-103PB1W
200 - 240 V AC, 50/60 Hz
1,090 W
1,310 W
0.5 W
0.5 W
0.3 W
0.3 W
Drive method : AC type
Drive method : AC type
85-inch, 16:9 aspect ratio
103-inch, 16:9 aspect ratio
1,889 mm (W) &times; 1,062 mm (H)
2,269 mm (W) &times; 1,276 mm (H)
&times; 2,167 mm (diagonal)
&times; 2,603 mm (diagonal)
2,073,600 (1,920 (W) &times;1,080 (H))
[5,760 &times; 1,080 dots]
0 &deg;C - 40 &deg;C
20 % - 80 %
NTSC, PAL, PAL60, SECAM, Modied NTSC
525 (480) / 60i &middot; 60p, 625 (575) / 50i &middot; 50p, 750 (720) / 60p &middot; 50p, 1125 (1080) / 60i &middot; 60p &middot; 50i &middot;
50p &middot; 24p &middot; 25p &middot; 30p &middot; 24sF, 1250 (1080) / 50i
VGA, SVGA, XGA, SXGA
UXGA &middot;&middot;&middot;&middot; (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz
BNC
RCA Pin jack &times; 2
BNC
BNC
BNC
RCA Pin jack &times; 2
DVI-D 24 Pin
Content Protection
Stereo mini jack (M3) &times; 1
High-Density Mini D-sub 15 Pin
1.0 Vp-p (75 )
0.5 Vrms, Shared with COMPONENT/RGB IN
TYPE A Connector
with sync 1.0 Vp-p (75 )
0.7 Vp-p (75 )
0.7 Vp-p (75 )
0.5 Vrms, Shared with VIDEO
Compliance with DVI Revision 1.0
Compatible with HDCP 1.1
0.5 Vrms, Shared with PC IN
Y or G with sync 1.0 Vp-p (75 )
Y or G without sync 0.7 Vp-p (75 )
PB/CB/B: 0.7 Vp-p (75 )
PR/CR/R: 0.7 Vp-p (75 )
HD/VD: 1.0 - 5.0 Vp-p (high impedance)
0.5 Vrms, Shared with DVI-D IN
Stereo mini jack (M3) &times; 1
External Control Terminal
D-sub 9 Pin
RS-232C compatible
for Wireless module (ET-WM200E / ET-WM200U)
RJ45 10BASE-T/100BASE-TX, compatible with PJLink™
RCA Pin jack &times; 2 (L / R)
[INPUT 1 kHz / 0 dB, 10 k: Load]
OUTPUT LEVEL : VARIABLE (-f ~ 0 dB)
160 mm &times; 40 mm &times; 2 pcs
20 W [10 W + 10 W] (10 % THD)
2,015 mm &times; 1,195 mm &times; 99 mm
2,412 mm &times; 1,419 mm &times; 134 mm
approx. 115 kg net
approx. 189 kg net
Note:
Design and specications are subject to change without notice. Mass and dimensions shown are approximate.
64
This product incorporates the following software:
(1) the software developed independently by or for Panasonic Corporation,
(2) the software owned by third party and licensed to Panasonic Corporation,
(3) the software licensed under the GNU General Public License, Version 2.0 (GPL-2.0),
(4) the software licensed under the GNU LESSER General Public License, Version 2.1 (LGPL-2.1) and/or,
(5) open source software other than the software licensed under the GPL and/or LGPL.
For the software categorized as (3) and (4), please refer to the terms and conditions of GPL-2.0 and LGPL-2.1, as
the case may be at
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
The GPL/LGPL software is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without
even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
At least three (3) years from delivery of products, Panasonic will give to any third party who contact us at the contact
information provided below, for a charge no more than our cost of physically performing source code distribution, a
complete machine-readable copy of the corresponding source code and the copyright notice, covered under
GPL-2.0/LGPL-2.1.
Contact Information
[email protected]
For the software categorized as (5) includes as follows.
1. The software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)
2. The software developed by the University of California, Berkeley and its contributors.
3. FreeType code.
4. The Independent JPEG Group's JPEG software.
5. thttpd code.
65
J GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your
freedom to share and change free software--to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s
software and to any other program whose authors commit
to using it. (Some other Free Software Foundation software
is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service
if you wish), that you receive source code or can get it if you
want it, that you can change the software or use pieces of it
in new free programs; and that you know you can do these
things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modied by
someone else and passed on, we want its recipients to know
that what they have is not the original, so that any problems
introduced by others will not reect on the original authors’
reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To
prevent this, we have made it clear that any patent must be
licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modication follow.
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which
contains a notice placed by the copyright holder saying it
may be distributed under the terms of this General Public
License. The “Program”, below, refers to any such program
or work, and a “work based on the Program” means either
the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion
of it, either verbatim or with modications and/or translated
into another language. (Hereinafter, translation is included
without limitation in the term “modication”.) Each licensee
is addressed as “you”.
Activities other than copying, distribution and
modication are not covered by this License; they are
outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered
only if its contents constitute a work based on the
Program (independent of having been made by running
the Program). Whether that is true depends on what the
Program does.
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium,
provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice
and disclaimer of warranty; keep intact all the notices
that refer to this License and to the absence of any
warranty; and give any other recipients of the Program a
copy of this License along with the Program.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Program
or any portion of it, thus forming a work based on the
Program, and copy and distribute such modications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) You must cause the modied les to carry prominent
notices stating that you changed the les and the
date of any change.
b) You must cause any work that you distribute or
publish, that in whole or in part contains or is derived
from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the
terms of this License.
c) If the modied program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and a notice
that there is no warranty (or else, saying that you
provide a warranty) and that users may redistribute
the program under these conditions, and telling the
user how to view a copy of this License. (Exception: if
the Program itself is interactive but does not normally
print such an announcement, your work based on the
Program is not required to print an announcement.)
66
These requirements apply to the modied work as a
whole. If identiable sections of that work are not derived
from the Program, and can be reasonably considered
independent and separate works in themselves, then
this License, and its terms, do not apply to those
sections when you distribute them as separate works.
But when you distribute the same sections as part of
a whole which is a work based on the Program, the
distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend
to the entire whole, and thus to each and every part
regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the
Program.
In addition, mere aggregation of another work not based
on the Program with the Program (or with a work based
on the Program) on a volume of a storage or distribution
medium does not bring the other work under the scope
of this License.
3. You may copy and distribute the Program (or a
work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2
above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge no
more than your cost of physically performing source
distribution, a complete machine-readable copy of the
corresponding source code, to be distributed under
the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as
to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred
form of the work for making modications to it. For
an executable work, complete source code means all
the source code for all modules it contains, plus any
associated interface denition les, plus the scripts used
to control compilation and installation of the executable.
However, as a special exception, the source code
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from
the same place counts as distribution of the source
code, even though third parties are not compelled to
copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute
the Program except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based on
it.
6. Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether
by court order, agreement or otherwise) that contradict
the conditions of this License, they do not excuse
you from the conditions of this License. If you cannot
distribute so as to satisfy simultaneously your obligations
under this License and any other pertinent obligations,
then as a consequence you may not distribute the
Program at all. For example, if a patent license would
not permit royalty-free redistribution of the Program by
all those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of
the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system, which is implemented
by public license practices. Many people have made
generous contributions to the wide range of software
distributed through that system in reliance on consistent
application of that system; it is up to the author/donor
to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
67
8. If the distribution and/or use of the Program is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Program under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to the
present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number. If
the Program species a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Program does not specify
a version number of this License, you may choose any
version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO
YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
68
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the
greatest possible use to the public, the best way to achieve
this is to make it free software which everyone can redistribute
and change under these terms.
To do so, attach the following notices to the program. It is
safest to attach them to the start of each source le to most
effectively convey the exclusion of warranty; and each le
should have at least the “copyright” line and a pointer to where
the full notice is found.
one line to give the program’s name and an idea of what it
does.
Copyright (C) yyyy name of author
This program is free software; you can redistribute it and/
or modify it under the terms of the GNU General Public
License as published by the Free Software Foundation;
either version 2 of the License, or (at your option) any later
version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write to the
Free Software Foundation, Inc., 51 Franklin Street, Fifth
Floor, Boston, MA 02110-1301, USA.
Also add information on how to contact you by electronic and
paper mail.
If the program is interactive, make it output a short notice like
this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of
author Gnomovision comes with ABSOLUTELY NO
WARRANTY; for details type ‘show w’.
This is free software, and you are welcome to redistribute
it under certain conditions; type ‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called something
other than ‘show w’ and ‘show c’; they could even be mouseclicks or menu items--whatever suits your program.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest
in the program ‘Gnomovision’ (which makes passes at
compilers) written by James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program is a
subroutine library, you may consider it more useful to permit
linking proprietary applications with the library. If this is what
you want to do, use the GNU Lesser General Public License
instead of this License.
J GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the rst released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2,
hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
freedom to share and change free software--to make sure
the software is free for all its users.
This license, the Lesser General Public License, applies
to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors
who decide to use it. You can use it too, but we suggest you
rst think carefully about whether this license or the ordinary
General Public License is the better strategy to use in any
particular case, based on the explanations below.
When we speak of free software, we are referring to freedom
of use, not price. Our General Public Licenses are designed
to make sure that you have the freedom to distribute copies
of free software (and charge for this service if you wish); that
you receive source code or can get it if you want it; that you
can change the software and use pieces of it in new free
programs; and that you are informed that you can do these
things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library
or if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object les to the
recipients, so that they can relink them with the library after
making changes to the library and recompiling it. And you
must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify
the library.
To protect each distributor, we want to make it very clear that
there is no warranty for the free library. Also, if the library
is modied by someone else and passed on, the recipients
should know that what they have is not the original version,
so that the original author’s reputation will not be affected by
problems that might be introduced by others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained
for a version of the library must be consistent with the full
freedom of use specied in this license.
Most GNU software, including some libraries, is covered
by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain
libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library.
The ordinary General Public License therefore permits
such linking only if the entire combination ts its criteria of
freedom. The Lesser General Public License permits more
lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License
because it does Less to protect the user’s freedom than the
ordinary General Public License. It also provides other free
software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries.
However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library. A
more frequent case is that a free library does the same job
as widely used non-free libraries. In this case, there is little
to gain by limiting the free library to free software only, so we
use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a
large body of free software. For example, permission to use
the GNU C Library in non-free programs enables many more
people to use the whole GNU operating system, as well as
its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users’ freedom, it does ensure that the user
of a program that is linked with the Library has the freedom
and the wherewithal to run that program using a modied
version of the Library.
The precise terms and conditions for copying, distribution
and modication follow. Pay close attention to the difference
between a “work based on the library” and a “work that
uses the library”. The former contains code derived from the
library, whereas the latter must be combined with the library
in order to run.
69
TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called “this License”). Each licensee
is addressed as “you”.
A “library” means a collection of software functions and/
or data prepared so as to be conveniently linked with
application programs (which use some of those functions
and data) to form executables.
The “Library”, below, refers to any such software library
or work which has been distributed under these terms.
A “work based on the Library” means either the Library
or any derivative work under copyright law: that is to
say, a work containing the Library or a portion of it,
either verbatim or with modications and/or translated
straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term
“modication”.)
“Source code” for a work means the preferred form
of the work for making modications to it. For a
library, complete source code means all the source
code for all modules it contains, plus any associated
interface denition les, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modication are not covered by this License; they are
outside its scope. The act of running a program using the
Library is not restricted, and output from such a program
is covered only if its contents constitute a work based
on the Library (independent of the use of the Library in a
tool for writing it). Whether that is true depends on what
the Library does and what the program that uses the
Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in
any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact
all the notices that refer to this License and to the
absence of any warranty; and distribute a copy of this
License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or
any portion of it, thus forming a work based on the
Library, and copy and distribute such modications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) The modied work must itself be a software library.
b) You must cause the les modied to carry prominent
notices stating that you changed the les and the
date of any change.
c) You must cause the whole of the work to be licensed
at no charge to all third parties under the terms of this
License.
70
d) If a facility in the modied Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked,
then you must make a good faith effort to ensure
that, in the event an application does not supply
such function or table, the facility still operates,
and performs whatever part of its purpose remains
meaningful.
(For example, a function in a library to compute
square roots has a purpose that is entirely welldened independent of the application. Therefore,
Subsection 2d requires that any application-supplied
function or table used by this function must be
optional: if the application does not supply it, the
square root function must still compute square roots.)
These requirements apply to the modied work as
a whole. If identiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based
on the Library, the distribution of the whole must be
on the terms of this License, whose permissions for
other licensees extend to the entire whole, and thus
to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights
or contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Library.
In addition, mere aggregation of another work not
based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the
notices that refer to this License, so that they refer to the
ordinary GNU General Public License, version 2, instead
of to this License. (If a newer version than version 2 of
the ordinary GNU General Public License has appeared,
then you can specify that version instead if you wish.)
Do not make any other change in these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion
or derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you accompany it with the complete
corresponding machine-readable source code, which
must be distributed under the terms of Sections 1 and
2 above on a medium customarily used for software
interchange.
If distribution of object code is made by offering access
to copy from a designated place, then offering equivalent
access to copy the source code from the same place
satises the requirement to distribute the source code,
even though third parties are not compelled to copy the
source along with the object code.
5. A program that contains no derivative of any portion of
the Library, but is designed to work with the Library by
being compiled or linked with it, is called a “work that
uses the Library”. Such a work, in isolation, is not a
derivative work of the Library, and therefore falls outside
the scope of this License.
However, linking a “work that uses the Library” with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the Library),
rather than a “work that uses the library”. The executable
is therefore covered by this License. Section 6 states
terms for distribution of such executables.
When a “work that uses the Library” uses material from
a header le that is part of the Library, the object code
for the work may be a derivative work of the Library
even though the source code is not. Whether this is true
is especially signicant if the work can be linked without
the Library, or if the work is itself a library. The threshold
for this to be true is not precisely dened by law.
If such an object le uses only numerical parameters,
data structure layouts and accessors, and small macros
and small inline functions (ten lines or less in length),
then the use of the object le is unrestricted, regardless
of whether it is legally a derivative work. (Executables
containing this object code plus portions of the Library
will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that work
also fall under Section 6, whether or not they are linked
directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modication
of the work for the customer’s own use and reverse
engineering for debugging such modications.
You must give prominent notice with each copy of the
work that the Library is used in it and that the Library
and its use are covered by this License. You must supply
a copy of this License. If the work during execution
displays copyright notices, you must include the
copyright notice for the Library among them, as well as a
reference directing the user to the copy of this License.
Also, you must do one of these things:
a) Accompany the work with the complete
corresponding machine-readable source code for
the Library including whatever changes were used in
the work (which must be distributed under Sections 1
and 2 above); and, if the work is an executable linked
with the Library, with the complete machine-readable
“work that uses the Library”, as object code and/or
source code, so that the user can modify the Library
and then relink to produce a modied executable
containing the modied Library. (It is understood that
the user who changes the contents of denitions les
in the Library will not necessarily be able to recompile
the application to use the modied denitions.)
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already
present on the user’s computer system, rather than
copying library functions into the executable, and (2)
will operate properly with a modied version of the
library, if the user installs one, as long as the modied
version is interface-compatible with the version that
the work was made with.
c) Accompany the work with a written offer, valid for at
least three years, to give the same user the materials
specied in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specied materials from
the same place.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the “work that
uses the Library” must include any data and utility
programs needed for reproducing the executable
from it. However, as a special exception, the
materials to be distributed need not include anything
that is normally distributed (in either source or
binary form) with the major components (compiler,
kernel, and so on) of the operating system on which
the executable runs, unless that component itself
accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that
do not normally accompany the operating system.
Such a contradiction means you cannot use both
them and the Library together in an executable that
you distribute.
7. You may place library facilities that are a work based
on the Library side-by-side in a single library together
with other library facilities not covered by this License,
and distribute such a combined library, provided that the
separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted,
and provided that you do these two things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to nd the accompanying
uncombined form of the same work.
71
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided under
this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void,
and will automatically terminate your rights under this
License. However, parties who have received copies,
or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full
compliance.
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places
the Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based on it.
13. The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
10. Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject to these
terms and conditions. You may not impose any further
restrictions on the recipients’ exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether
by court order, agreement or otherwise) that contradict
the conditions of this License, they do not excuse
you from the conditions of this License. If you cannot
distribute so as to satisfy simultaneously your obligations
under this License and any other pertinent obligations,
then as a consequence you may not distribute the
Library at all. For example, if a patent license would
not permit royalty-free redistribution of the Library by all
those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of
the Library.
If any portion of this section is held invalid or
unenforceable under any particular circumstance,
the balance of the section is intended to apply, and
the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or
to contest validity of any such claims; this section has
the sole purpose of protecting the integrity of the free
software distribution system which is implemented
by public license practices. Many people have made
generous contributions to the wide range of software
distributed through that system in reliance on consistent
application of that system; it is up to the author/donor
to decide if he or she is willing to distribute software
through any other system and a licensee cannot impose
that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this License.
Each version is given a distinguishing version number.
If the Library species a version number of this License
which applies to it and “any later version”, you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
license version number, you may choose any version
ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into
other free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our
decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of
promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE
OF CHARGE, THERE IS NO WARRANTY FOR
THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS
AND/OR OTHER PARTIES PROVIDE THE LIBRARY
“AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO
THE QUALITY AND PERFORMANCE OF THE LIBRARY
IS WITH YOU. SHOULD THE LIBRARY PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE
THE LIBRARY (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED
INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO
OPERATE WITH ANY OTHER SOFTWARE), EVEN
IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
72
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the
greatest possible use to the public, we recommend making it
free software that everyone can redistribute and change. You
can do so by permitting redistribution under these terms (or,
alternatively, under the terms of the ordinary General Public
License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
le to most effectively convey the exclusion of warranty; and
each le should have at least the “copyright” line and a pointer
to where the full notice is found.
one line to give the library’s name and an idea of what it
does.
Copyright (C) year name of author
This library is free software; you can redistribute it and/
or modify it under the terms of the GNU Lesser General
Public License as published by the Free Software
Foundation; either version 2.1 of the License, or (at your
option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU Lesser General
Public License for more details.
You should have received a copy of the GNU Lesser
General Public License along with this library; if not, write
to the Free Software Foundation, Inc., 51 Franklin Street,
Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and
paper mail.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a “copyright
disclaimer” for the library, if necessary. Here is a sample; alter
the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in
the library ‘Frob’ (a library for tweaking knobs) written by
James Random Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
That’s all there is to it!
73
OpenSSL
This is a copy of the current LICENSE le inside the CVS repository.
LICENSE ISSUES
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL
License and the original SSLeay license apply to the toolkit. See below for the actual license
texts. Actually both licenses are BSD-style Open Source licenses. In case of any license issues
related to OpenSSL please contact [email protected].
OpenSSL License
Copyright (c) 1998-2006 The OpenSSL Project. All rights reserved. Redistribution and use in
source and binary forms, with or without modication, are permitted provided that the
following conditions are met:
1 Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2 Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the follo wing disclaimer in the documentation and/or other materials
provided with the distribution.
3 All advertising materials mentioning features or use of this software must display the
following acknowledgment: “This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)”
4 The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or
promote products derived from this software without prior written permission. For
written permission, please contact [email protected].
5 Products derived from this software may not be called “OpenSSL” nor may “OpenSSL”
appear in their names without prior written permission of the OpenSSL Project.
6 Redistributions of any form whatsoever must retain the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS’’ AND ANY
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
74
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software written by Tim Hudson ([email protected]).
Original SSLeay License
/ Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved.
This package is an SSL implementation written by Eric Young ([email protected]). The
implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following
conditions are aheared to. The following conditions apply to all code found in this distribution,
be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation
included with this distribution is covered by the same copyright terms except that the holder is
Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be
removed. If this package is used in a product, Eric Young should be given attribution as the
author of the parts of the library used.
This can be in the form of a textual message at program startup or in documentation (online or
textual) provided with the package. Redistribution and use in source and binary forms, with or
without modication, are permitted provided that the following conditions are met:
1 Redistributions of source code must retain the copyright notice, this list of conditions
and the following disclaimer.
2 Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
3 All advertising materials mentioning features or use of this software must display the
following acknowledgement: “This product includes cryptographic software written by
Eric Young ([email protected])” The word ‘cryptographic’ can be left out if the rouines
from the library being used are not cryptographic related :-).
75
4 If you include any Windows specic code (or a derivative thereof) from the apps
directory (application code) you must include an acknowledgement: “This product
includes software written by Tim Hudson ([email protected])”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS’’ AND ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative of this
code cannot be changed. i.e. this code cannot simply be copied and put under another
distribution licence [including the GNU Public Licence.]
76
thttpd
Copyright (c) 1995,1998,1999,2000,2001 by Jef Poskanzer &lt;[email protected]&gt;.
All rights reserved.
Redistribution and use in source and binary forms, with or without
modication, are permitted provided that the following conditions
are met:
1. Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS “AS IS’’ AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
77
Customer’s Record
The model number and serial number of this product can be found on its rear panel. You should note this serial
number in the space provided below and retain this book, plus your purchase receipt, as a permanent record of your
purchase to aid in identication in the event of theft or loss, and for Warranty Service purposes.
Model Number
Web Site : http://panasonic.net
&curren; Panasonic Corporation 2013
Serial Number
Printed in Japan
M0213-0
">
Hello! I am an AI chatbot specifically trained to assist you with the Panasonic TH-103PB1W Interactive Plasma Display Operating Instructions. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!
Assistant typing
Assistant terminated
Key Features

Interactive Plasma Display
HDMI input
Component/RGB input
PC input
DVI-D input
Serial control
On-screen menu displays
Picture adjustments
Sound adjustment
Setup menu
Frequently Answers and Questions

How do I connect my computer to the Plasma Display?

You can connect your computer using the PC input terminal, DVI-D input terminal, or the Serial terminal.
What are the different input signals I can use with the Plasma Display?

You can use PC, NETWORK, VIDEO, COMPONENT, HDMI, and DVI input signals.
How do I adjust the picture settings?

You can adjust the picture settings using the Picture menu, which allows you to change settings like brightness, contrast, color, and sharpness.
How do I set up the screensaver?

The screensaver is designed to prevent image retention on the Plasma Display. You can set the screensaver time in the Setup menu.
How do I use the ECO mode?

The ECO mode helps to save energy. You can enable or disable the ECO mode in the Setup menu.
Key Features

Frequently Answers and Questions

How do I connect my computer to the Plasma Display?

What are the different input signals I can use with the Plasma Display?

How do I adjust the picture settings?

How do I set up the screensaver?

How do I use the ECO mode?

Related

Panasonic plasma TV PH30U TH-42PH30U, TH-50PH30U Operating Instructions

Panasonic TH85PB1U Flat Panel Television User manual

Panasonic TH-50PH30E Plasma TV Operating Instructions

Interactive Plasma Display TH-85PB1E, TH-103PB1E Operating Instructions

Panasonic TH-152UX1 Operating Instructions

Panasonic TH-42PF50U Flat Panel Television User manual

Panasonic TH-65PB1U touch screen monitor Operating instructions

Panasonic TH-PF20W TH-42PF20W, TH-PF20W TH-50PF20W Operating Instructions

Panasonic TH-PF50E TH-42PF50E, TH-PF50E TH-50PF50E Operating Instructions

Panasonic TH-65PB1 Owner Manual

Panasonic TH-42PF20U, TH-50PF20U Operating Instructions Manual

Panasonic TH-65PF20U Flat Panel Television User manual
