Document
CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mounting recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
fan INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
control features:
4-Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
READ AND SAVE THESE INSTRUCTIONS
SAFETY FIRST
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner’s manual completely and carefully. Retain this manual for future reference.
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFORE YOU START
• CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical
codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and
possible damage to other equipment, do not install control to a receptacle, fluorescent light fixture, motor operated
appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.58 amps or 190 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
NOTES
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
FUSE BOX
(Remove fuse for the
circuit you will be
working on)
from wall to
end of blade
18"
70”
from wall to
center of fan
CIRCUIT BREAKER
(Trip breaker for the
circuit you will be
working on)
PN C2343001
AT0409
84”
from bottom
edge of blade
to floor
1
MOUNTING RECOMMENDATIONS
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation,
and fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting
recommendations as you decide where to install your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7’ above the floor.
• Do not locate the fan in a doorway or above a swinging door.
• In any installation, the tips of the blades must be at least 18” from the wall in order to provide sufficient
clearance for the blades.
• In bedrooms, fans work best when mounted above the foot of the bed.
• In low ceiling locations, our optional Low Ceiling Adaptor (LCA—available at
extra cost) can be used to gain 31¦2” on certain fan models.
• Over pool tables, be sure to provide plenty of clearance to avoid damage from
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan blades.
• Do not install a fan close to, or over, a pool or spa. High humidity combined
with corrosive gases will destroy the finish and warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52” fan even in
smaller rooms. For very large rooms, two fans may be needed.
SLOPED CEILING INSTALLATIONS
Suggested Extension Pole Lengths
Ceiling Height
Pole Length
8’
Standard
8’ 6”
Standard
9’
6”
9’ 6”
12”
10’
12”
11’
18”
12’
24”
13’
36”
14’
48”
When to Use Extension Poles
For best performance and best appearance,
an extension pole should be used with
your Casablanca fan when installing
on high (cathedral) ceilings or sloped
ceilings. Casablanca offers standard poles
in increments of 6” up to 5’. Custom poles
are available in lengths up to 9’ 9”. See
your Authorized Casablanca Dealer for
details.
Note: Fan may wobble or vibrate if
pole length is not long enough and
inside blade is too close to downslope
or side wall. Extending pole length
will usually solve problem.
Calculation of 32°
Use the tear-off Ceiling Angle Template card inserted in the
back of this manual, it provides you with a simple ‘go’ or
‘no-go’ for installing your fan on a sloped ceiling.
2
Extension
Pole
maximum
hang-tru®
angle 32º
32°
blades must be
a minimum of 7′
above the floor
7′ minimum
EXAMPLE 1
This slope is less than 32½.
It is OK to install your fan.
EXAMPLE 2
This slope is 32½. This is the maximum
slope that will allow the fan to hang
straight down. It is OK to install your
fan.
EXAMPLE 3
This slope is more than 32½.
Your fan will not hang straight down, an
adaptor is necessary. Contact your local
Authorized Casablanca Dealer in regards to
purchasing a “Slope Ceiling Adaptor.”
Key Largo™ II
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging material, be certain that all parts have been removed.
perma•lock™ hardware
ALLEN SET SCREW
¼-20 x¼”
(pre-installed)
downrod & Ball
assembly
3mm
allen wrench
Fan preparation
important safety information!
motor
wires
before starting the installation of your ceiling fan, install the
threaded downrod into the motor coupling and lock the assembly
ground
wire
Prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma•Lock™ downrod and ball assembly.
downrod
& Ball
assembly
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread the
downrod into the motor coupling until it stops turning, this
will take at least four and a half full turns.
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
tapered
thread
ALLEN
SET SCREW
motor
coupling
CAUTION: Failure to fully lock in the downrod before securely tightening the allen set
screw may cause the fan to separate from
the downrod during normal operation!
3
getting started
Installing a New Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish
to place your Casablanca fan, an approved ceiling fixture
outlet box must be installed and wired.
Warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting
hardware provided with the outlet box.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either circuit
breaker or fuse box), lower the old fixture and disconnect
the wiring. Check the ceiling fixture outlet box to be sure
that it is marked ‘Approved for ceiling fan mounting’. If it is
not, a new box must be installed.
NOTE: The fan weight is 33 pounds.
CEILING HARDWARE & support instalation parts
additional hardware
CROSSBAR MOUNTING BRACKET
27/16” x 8-32 rounded
head screw (2)
1” x 8-32 rounded
head screw (2)
LAG SCREW
/8” #7 X 5” (1)
3
WIRE NUT (4)
FLAT WASHER (2)
Crossbar Mounting Bracket INSTALLATION
Note: After removing the old fixture, check the outlet box
to insure that it is supported by a joist or beam across its
upper surface. If not, a 2” x 4” stud must be installed.
JOIST
Step 1a. Remove the knockout plug in the center of the outlet box or drill a 1/2” hole for the lag screw to pass through.
Then drill a 1/4” guide hole into the joist or beam to a depth
of 3”.
Step 1b.Route the outlet box wires through the keyhole slot of
the crossbar mounting bracket as shown. Attach the crossbar
mounting bracket to outlet box with screws provided, assuring
that the outlet box wires are not pinched by the washer.
CAUTION: To reduce the risk of personal injury,
use only the mounting hardware provided with
the approved outlet box to install the crossbar
mounting bracket.
WARNING!
SUPPORT DIRECTLY TO
BUILDING STRUCTURE ONLY.
ceiling fan
approved
wiring box
crossbar
mounting
bracket
flat
washer
approved
outlet box
hardware
4
ceiling
wiring
ridge
side
down
green
ground
wire
Key Largo™ II
LAG SCREW INSTALLATION
Step 2. Pass the lag screw through the center hole of the
crosbar mounting bracket and screw into guide hole. Tighten
until outlet box is firmly mounted to beam. This box must
be firmly secured to the ceiling. We recommend that the
ceiling fixture outlet box be of sufficient capacity enabling
it to support the weight of fan and light fixture under any
conditions.
lag
screw
CANOPY HARDWARE
CANOPY
HATCH
CANOPY SCREW (4)
CANOPY
CANOPY LOCK WASHER (4)
phillips
screwdriver
CANOPY INSTALLATION
Step 3. Attach the canopy to the crossbar mounting bracket
with three of the 8-32 x 21/4” long canopy screws and canopy
lock washers. Tighten the screw firmly by hand only with the
provided screwdriver..
canopy
Note: On sloped ceilings, align the
canopy opening towards the top or
room peak.
canopy
lock washer
canopy screw
5
HANGING THE FAN
Step 4. To hang the fan body in the
canopy, hold the fan body firmly and insert
the ball into the canopy opening. Check
that no wires were pinched. Rotate the fan
body until the slot in the ball fits into the
pin opposite the canopy opening.
ball
NOTE: The fan weight is 33 pounds.
slot
pin
CANOPY ELECTRICAL CONNECTIONS
Step 5. Attach the fan wires to the ceiling fixture outlet box wiring by twisting
the bare ends of the wires together and
then securing with a wire nut.
Connect in this order:
• GREEN leads from mounting plate
and fan to GROUND conductor of
power source. Secure with wire
nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet
box. Secure with wire nut.
• BLUE wire and BLACK power wire
from fan to BLACK power wire in
ceiling outlet box. Secure with wire
nut.
BLACK & BLUE
D1-OPTION WIRES
(2)
WHITE WIRES
(2)
GREEN WIRES
(3)
wire nut
CANOPY HATCH INSTALLATION
Step 6a. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
Step 6b. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from the
hatch opening.
Tighten the screws firmly by hand only
with the provided screwdriver.
Step 6c. Straighten the fan, then check
to ensure that there is no movement between the canopy and ceiling or Hang-Tru
ball and top support shaft.
Note: Write down the Serial
Number and the model number for future reference from
the top of the fan.
6
canopy
hatch
lock
washer
canopy
screw
tilt the
fan to
install
last
canopy
screw
Key Largo™ II
remove dummy switch housing & shipping blocks
Step 7a. To reach the blade holder mounting
holes in the fan motor the dummy switch
housing must be removed.
Take out the two 6-32 X 3/8” screws securing
the dummy switch housing and remove. Put
the two (2) screws aside for the moment,
they will be used in Step 10 to install
the switch housing after the blades are
installed.
The dummy switch housing is used only when
shipping the fan.
Note: Save these two screws–they
will be used in Step 10!
Shipping
blocks
Step 7b. Unscrew and remove the 10 shipping blocks. Put the ten screws aside for the
moment, they will be used in Step 8.
The shipping blocks can be discarded; they
are used only when shipping the fan.
BLade & Blade holder hardware
BLADE SCREW
AND WASHER
(4 PER BLADE)
BLADE
HOLDER
BLADE HOLDER
SCREW
(2 PER BLADE)
blade Badge installation
BLADE SCREW
and washers
(4 PER BLADE)
Step 8. Attach each blade to a blade
holder by first pressing the blade badge
into the blade, then installing the blade
holder using the four blade screws provided for each blade.
Using a screwdriver tighten securely by
hand only.
Repeat for each blade assembly
BLADE
HOLDER
BLADE
(sold seperately)
7
blade/blade holder installation
Step 9. Using the blade holder screws, attach
each blade/bladeholder assembly to the motor
with the bamboo stitch facing down.
Using the screwdriver, tighten securely by hand
only.
WARNING! To reduce the risk of personal injury, do not bend the blade
brackets when installing the brackets,
balancing the blades, or cleaning the
fan. Do not insert foreign objects in
etween rotation fan blades.
Blade holder
screws(2 per blade)
completing installation
switch housing
switch housing
mount Screw
6-32 X 3/8”
(2)
cap
install switch housing
Step 10a. Install the two 6-32 X 3/8” screws
onto the switch housing plate, leaving approximately 1/8“ of the threads exposed for
installation of the switch housing.
Step 10b. Line up the two inner clearance
holes in the cup with the two screws installed
in previous step.
CAUTION! Before continuing to the
next step check that a wire or component inside the switch housing will
not be pinched as it is installed.
Step 10c. Plug the wire connector for the
fan into the wire connector for the switch
housing. Assure that the clip from the fan
connector engages the notch on the switch
housing connector.
notch
clip
Step 10d. Rotate cup so that the screws are
aligned with the smaller side of the clearance
holes. Tighten securely by hand only.
8
switch
housinG
PLATE
switch housing
mount Screw
6-32 X 3/8”
(2)
Key Largo™ II
installing the Switch Housing cap
Step 11a. Line up the two clearance holes
in the cap with the two threaded holes
on the raised rim of the switch housing.
Press the cap onto the switch housing to
seat the guide pins into the alignment
holes of the switch housing.
Step 11b. Using the two (2) 8-32 X 3/8”
screws removed in Step 9, install the cap
onto the switch housing.
Tighten securely by hand only.
9
4-Speed
4-SPEED OPERATION
Pull-chain switches on the fan control the fan and lights.
Using the fan control pull-chain switch: Fan off at start.
First pull: fan ON, High speed
Second pull: Medium speed
Third pull: Medium Low speed
Fourth pull: Low speed
Fifth pull: Fan OFF
Using the optional light pull-chain switch: Light off at
start.
First pull: light ON
Second pull: light OFF
Direction of blade rotation is controlled by the reverse slide
switch on the side of the switch housing.
No changes in household wiring are required.
OPTIONAL LIGHT
PULL CHAIN
SWITCH
FAN & SPEED CONTROL
PULL CHAIN SWITCH
REVERSE
SWITCH
4-SPEED • OPTIONAL WALL CONTROL • W-24 (SOLD SEPARATELY)
1. Raise slider to increase fan speed, lower to decrease.
2. Four speeds are available: High, Medium, Low 2, and Low 1. The bottom position is OFF.
4-SPEED • OPTIONAL WALL CONTROL • W-28 (SOLD SEPARATELY)
1. Raise the fan slider to increase fan speed, lower to decrease.
2. For the fan, four speeds are available: High, Medium, Low 2, and Low 1. The bottom position
is OFF.
3. The light slider is a dimmer, the bottom is OFF, raise to increase intensity of the light.
4. The toggle switch is a separate preset control — turns both the fan and light off or on to the
current setting.
10
Key Largo™ II
Care Recommendations
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened
soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
Blades
• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be
applied for added protection and luster.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a
mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents
as these will damage the finish.
• WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing the
blades, or cleaning the fan. Do not insert foreign objects in betweeen rotating fan blades.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated
for life.
• Do not attempt to oil the motor.
Changing Lightbulbs
• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light fixture.
• The maximum wattage rating for this fan’s light kit is 120 watts for the light.
For questions or to locate the nearest Casablanca Authorized Service Center,
call toll-free 1-888-227-2178 or visit us on the Web at www.casablancafanco.com
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications
to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
Product Specifications
Model Name: Key Largo™ III
Model Number: C23UxxK
Dimensions:
NOTE: Dimension B
includes light fixture
and glass.
A = 12.3"
B = 13"
C =
3"
D =13.14"
E = 5.6"
Weight:
33 lbs.
Motor:
Blade Span:
Blade Pitch:
No. of Blades:
Technology:
188mm x 20mm Direct Drive
52"
15°
5
4-Speed
™
Airflow:
5,510 cfm
Electricity Use*: 80 watts
Airflow Efficiency*: 69 cfm/watt
* Performance data is for fan only. No lighting wattage is included.
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement