Instruction Manual - Hoover Service › Manuals, troubleshooting

Instruction Manual - Hoover Service › Manuals, troubleshooting
Introductión
Read this manual carefully as it offers practical
advice to help you get the most from your washing
machine.
This «Instruction and Installation Manual»
contains everything you need to know about the
everyday running of your machine.
Please refer to this manual for installation and
maintenance instructions.
The manual also
contains information about possible working
problems, advice about sorting clothes for
washing, an explanation of label symbols and hints
about how to remove stubborn stains.
1.- CONTROL PANEL
2.- LID
3.- DRUM
4.- DETERGENT DISPENSER
5.- PLINHTT PANEL
6.- FILTER
Table of contents
page
Safety measures
Setting up - Installation
Guarantee
Preparing the wash. Opening/ closing the drum
Detergent load
Electronically-controlled variable load- Fuzzy Logic
Specific programmes
General recommendations
Troubleshooting
Washing hints
3
5
6
7
8
8
9
10
12
13
Safety measures
This appliance meets the European Directives
2004/108/EC, 2006/95/EC which have been substituted
respectively by 89/336/EEC, 73/23/EEC and subsequent
modifications thereof.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
ATTENTION: FOR ALL CLEANING AND MAINTENANCE
WORK
• Remove the plug.
• Turn off the water inlet tap after each wash.
3
• The manufacturer fits all the machines with an earth
connection.
Ensure that the electrical installation has an earth connection
and that it is connected; if not, call a qualified Service Center.
The earth connection is essential for user safety as it eliminates the risk of electrical discharge.
• Power sockets should be in easily accessible places so that
the washing machine can be unplugged in case of any
problems.
• If the electric cable is damaged replace with an original set
(cable and plug) supplied by the manufacturer or official aftersales service.
note:
In the event that it is necessary to replace the power cable,
make sure that you comply with the following colour-code chart
during the wiring:
blue
neutral
brown
phase
Yellow-green
earth
The manufacturer accepts no responsibility for any
damage to people or things resulting from the failure to
comply with the appliance’s installation and safety
regulations.
• Do not touch the appliance with wet hands or feet.
• Do not use the appliance when bare-footed.
• Use extension cords only with extreme care.
• Do not use adapters or multiple plugs.
• Do not allow the appliance to be used by children or the infirm
without due supervision.
• Do not pull on the power cord or the appliance itself to remove
the plug from the socket.
• Do not leave the appliance outdoors or exposed to the
atmospheric elements (rain, sun, etc.).
• Do not cover the appliance with cloth or plastic while it is
working.
• Do not install the appliance in damp places or anywhere
where it could be sprayed by the shower.
• Do not install the appliance on a surface which obstructs the
space between the floor and the base of the machine.
• Keep all packaging out of the reach of children as it could
constitute a health hazard.
ATTENTION:
DURING A WASH CYCLE THE WATER
CAN REACH TEMPERATURES OF 90ºC.
4
Setting up - Installation
• Unpack the appliance.
• Remove the 4 screws (A) from
both clamps and the 4
screws (B).
• Replace the 4 screws (A) and
fit the trims provided (D).
If your model offers this function:
Position the protection sheet as shown in the
diagram.
1.- Washing machine with wheel trolley.
2.- Washing machine without wheel trolley.
ATTENTION: DO NOT TURN THE TAP ON
• The washing machine should be connected to the
water mains via the new tube supplied with the
appliance (inside the drum). Do not use the old tube for
this purpose.
• Connect one end of the water inlet pipe with the elbow
bend to the electrovalve (top rear part of the machine)
and the other end to a tap or a plumbed-in 3/4" gas
threaded connection.
• Place the washing machine close to the wall, ensuring
that there are no bends or kinks anywhere in the tube.
Hook the outlet pipe to the edge of the sink or preferably
to a fixed drainage outlet of a diameter greater than that
of the outlet pipe and at a height of min. 50 cm. and a
maximum of 75 cm. from the floor.
If necessary, use the curved accessory to attach and
support the outlet pipe more securely.
5
If your model offers this function:
• To move the washing machine easily, turn the trolley
lever to the right. Once you have finished moving the
machine, return the lever to its original position.
• Level the machine by adjusting the front feet.
a) Turn the nut clockwise to release the screw on the
foot.
b) Raise or lower the foot by rotating it until it stands
firmly on the floor.
c) Lock the foot in position by turning the nut
anticlockwise until it comes up against the bottom of the
washing machine.
Check that the appliance is properly levelled.
Check that the washing machine does not rock by trying
to move two diagonally opposite top corners at the
same time.
• If you move the washing machine from one place to
another, you must level the feet again afterwards.
• Connect the machine.
Guarantee
1.
The appliance is accompanied by a Guarantee
Certificate.
A
2.
Complete part A and keep it. It must be presented
to the Technical Assistance Centre in the event of
a repair being necessary, along with the legal
receipt issued by the dealer on purchase.
6
Preparing the wash. Opening/ closing the drum
ATTENTION:
IT IS IMPORTANT TO MAKE SURE THAT THE
DRUM IS CAREFULLY OPENED AND CLOSED,
OTHERWISE THE MACHINE OR LAUNDRY
COULD GET DAMAGED.
ENSURE THAT THE DOORS FIT TOGETHER
PERFECTLY AND ARE PROPERLY CLOSED.
Loading
1.
Open the washing machine lid.
2.
Open the drum by pressing the white button with
one hand while pressing down on the opposite door
with the other.
3.
Place clothes in the drum one item at a time, and
without squashing. Do not exceed the load limits
recommended in the “programme table”. An
overloaded washing machine will not wash properly,
and will leave clothing wrinkled.
4.
To close the drum, place the doors so that the one
with the white button is below the other and they fit
together perfectly.
7
Detergent load
I
Maximum
pre-wash and main wash
washing powder
recommended
II
Maximum
Main wash
washing liquid
Maximum
bleach and scenting agent
The detergent dispenser is divided into 4 compartments:
.- Compartment I is for the pre-wash detergent.
.- Compartment II is for the main wash detergent.
.- The compartment
is for bleach.
is for fabric conditioners, scenting agents and special additives such as starch,
.- The compartment
blueing, etc.
The detergent dispenser has two reference marks:
.- Recommended (lower reference mark). This indicates the recommended level for the pre-wash and
main wash compartments.
.- Max. This indicates the maximum level, which should never be exceeded.
Important:
- We recommend not using bleach for programs with a prewash cycle.
- Do not use liquid detergent for programs with a prewash cycle and/or timed start.
Electronically- controlled Variable Load – Fuzzy Logic
This machine has electronics that automatically process all stages of the wash to ensure exceptional
results and at the same time save you time and money.
Once a programme has been selected, the machine optimises the following elements depending on
the wash load and type of fabric:
- quantity of water and power consumption
- wash time
- rinse efficiency
The washing machine also:
- detects suds and increases the amount of rinse water if necessary
- adjusts spin speed according to load distribution, thus forestalling any imbalance in the mechanism.
8
Specific / special programmes
SPECIAL RINSE PROGRAMME
Programme
runs 3 rinses with spins at 800 rpm (this speed may be reduced or spin
cancelled using the appropriate button). It works for all fabrics and can be used, e.g. after
garments are hand washed.
SPECIAL HIGH-SPEED SPIN PROGRAMME
Programme
runs a spin at the speed indicated in the programme table.
EMPTY ONLY
Programme
empties the water from the machine.
HAND WASH
The washing machine also has a delicate washing cycle called "hand wash". The
programme runs a complete wash cycle for garments intended to be hand washed. It
washes at no more than 30 ºC and finishes with three rinses and a delicate spin.
SPORTSWEAR
The machine has an exclusive programme for sportswear. It is intended for mixed
sportswear which should not be washed with high-temperature programmes.
It begins with a cold pre-wash to soften and eliminate the worst of the dirt, then runs a 30
ºC wash, a rinse and a delicate spin to ensure maximum care for delicate, heavily soiled
garments.
CLASS AA
Optimum wash performance can be obtained at 40 ºC with Class A power consumption.
CLASS A
It is possible to obtain an optimum wash performance with a maximum load of 3 kg at a
temperature of 60 degrees C with a considerable reduction in time.
MIX
&
WASH
MIX & WASH
The MIX & WASH programme allows different types of fabric to be washed at the same
time.
- new coloured garments must be washed separately the first time.
- never mix non-fast coloureds.
EXPRESS PROGRAMMES
EXPRESS
44´ MINUTE EXPRESS PROGRAMME
29´ MINUTE EXPRESS PROGRAMME
32´ MINUTE EXPRESS PROGRAMME
These programmes run a complete wash cycle at 40/50 ºC for up to 3.5 kg of washing in
44/32 or 29 minutes.
REMARKS
1. For heavily soiled washing we recommend loads of no more than 3 kg.
2. Bleach can be added via dispenser ( ) for the WHITE 90º and FAST COLOUR
60º COTTONS programmes.
3. The machine is designed to apply fabric softener automatically in the last rinse of
all wash cycles.
9
General recommendations
CLEANING AND MAINTENANCE OF THE MACHINE
Do not use abrasives, spirits or solvents when cleaning the exterior of the washing machine. It is sufficient
to use a damp cloth.
The washing machine requires very little maintenance.
• Drying the rubber seal of the drum.
• Cleaning the dispenser and its compartments.
• Cleaning the filter.
• Cleaning prior to removals or when the machine is to stand idle for long periods.
To help conserve the washing machine, dry the rubber seal and leave the door open when the
cycle ends.
CLEANING THE FILTER
The washing machine comes with a special filter, located behind the machine’s front plinth panel, that
collects larger objects (coins, buttons, etc.) which could even block the pump.
It is advisable to clean the filter whenever the machine fails to rinse the clothes as well as it should
or when it fails to drain properly.
When it is necessary to clean the filter, proceed as follows:
• Use a basin to collect the water coming out.
• Remove the filter and clean it.
• Once the filter is clean, replace it by following the abovementioned pro in reverse.
10
CLEANING THE DETERGENT DISPENSER AND ITS COMPARTMENTS
.- It is advisable to clean the four compartments of the
detergent dispenser (pre-wash, wash, bleach and fabric
conditioner) from time to time. To do this, remove the detergent
dispenser and after cleaning it, fit it back in place.
To remove and fit the detergent dispenser, follow the steps
indicated in the images.
A
removing
.- Press button A
.-Hold down the button and turn the detergent dispenser
outwards
I
II
.- Remove the dispenser and clean it
.- In the case of the pre-wash (I) and wash (II) compartments,
it is advisable to remove any dried-in remains of detergent
which obstruct the flow of the detergent to the drum.
S
B
.- In the case of the bleach and fabric conditioner
compartments, the two traps (S) located at the rear part of the
dispenser should be removed by pulling them out.
Remove any solid residue which could block the holes in the
compartments.
fitting
.- Fit in the tabs as shown
C
.- Turn the detergent dispenser towards the housing (C) in the
door until the tab clicks into place.
11
Troubleshooting
FAULT
1.- No programme works
CAUSE
• The appliance is not plugged
in.
• The general switch is disconnected.
• There is no electricity.
• The fuses in the electric installation are damaged.
• The door is open.
SOLUTION
• Plug it in.
2.- The appliance does not
load water
• See causes for 1.
• The tap is turned off.
• Check.
• Turn on the tap.
3.- The water does not drain
• The filter is clogged.
• The outlet pipe is bent.
• Check the filter.
• Straighten the outlet pipe.
4.- The spin function does not • The washing machine has not
work
yet drained the water.
• The “Spin Exclusion” option is
activated.
5.- Strong vibrations during
spin cycle
6.- The high-speed spin does
not work
• Activate the general switch.
• Check.
• Check.
• Close the door.
• Wait a few minutes for the washing machine to drain.
• Enable the spin option.
• Adjust the feet.
• The washing machine is not
correctly levelled.
• The anchoring device for trans- • Remove the transport support.
port has not been removed.
• The wash load is not evenly
• Distribute it evenly.
distributed.
• The wash load is not evenly
distributed within the drum.
• Distribute the wash load evenly
in the drum.
If the problem or malfunctioning persists, disconnect the
machine, turn off the tap and do not try to repair.
For all repairs contact an Official Technical Assistance centre
(consult the European guarantee sheet) and always insist on the
use of original parts. Failure to do so may compromise the safety
of your machine.
When contacting a Technical Assistance Centre always refer to
the model (see also control panel) and the registration and serial
numbers indicated on the plate at the bottom front of the
machine behind the plinth panel or on the guarantee certificate.
That is to say, everything that appears in the box.
Providing this information will ensure a faster and more efficient
service.
12
Washing hints
Hints on the most economical, most environmentally friendly way to use your washing machine.
HINTS ON USING YOUR WASHING MACHINE
Wait until you have a full load before using the machine: this will avoid the use of more water and power
than necessary.
We recommend using the full load capacity: this could save you up to 50% in power consumption. Wash a
single full load rather than two light loads.
WHEN IS PRE-WASHING NECESSARY?
Only when washing heavily soiled clothes.
With clothes that are not especially dirty, you can save between 5 and 15% by not using this option.
WHAT WASH TEMPERATURE SHOULD I USE?
Applying a stain remover before placing clothes in the machine will eliminate the need for wash
temperatures of more than 60 ºC.
When loading a wash into the drum, we recommend that you:
• For specially delicate garments we recommend the use of a protective net.
• Empty all pockets and ensure that they do not contain metal objects (paperclips, safety pins, pins,
coins,etc.).
• Fasten pillow slips, close all zips and fastenings, and tie any loose ribbons or belts from dresses.
• Remove all runners (metal and plastic) from curtains and net curtains. We recommend that the ribbon be
gathered into a ball and tied with its own cord.
• Unfold all items to be washed.
• Be careful not to exceed the recommended load for each programme.
• When washing rugs, bedspreads and other highly absorbent items, cancel the spin option.
• In order to be able to wash woollens in the washing machine they must carry the “Pure New Wool”
symbol as well as the information “does not become matted” or “machine washable”.
• If possible, do not wash only towels. Mix them with your regular washing.
• Ensure that no item becomes trapped between the drum doors.
LABEL SYMBOLS
Labels are usually sown into the collar or side seams. The symbols which appear on them indicate the
following:
• Maximum WASH temperature.
• Appropriate and inappropriate washing methods.
• Appropriate and inappropriate washing products.
The symbols are as follows:
WASH
Washing instructions always appear as a basin with different indications:
• Do not wash.
• Can be washed both by hand or in the washing machine. The figures in the basin indicate the
maximum wash temperature.
13
• Hand wash only.
When the hand is half submerged in the water, this means that the item should be tumbled only
gently during washing. If it is fully submerged in the water, this means that the garment should
only be washed by hand.
• The line under the basin means that the item should be washed on a gentle cycle.
• Do not spin.
BLEACH
Bleach is widely used to whiten fabrics, although in some cases it can cause irreparable damage. There
are various symbols which refer to its use.
• Bleach can be used.
• Do not use bleach.
WEEE
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product.
The symbol on the product indicates that this product may not be treated as household waste. Instead it
shall be handed over to the applicable collection point for the recycling of electrical and electronic
equipment
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you purchased the product.
EN
The manufacturer declines all responsibility in the event of any printing
mistakes in this booklet. The manufacturer also reserves the right to make
appropriate modifications to its products without changing the essential
characteristics.
14
WASHING MACHINE HNT 6414
S
V
B1 C1 C2 C3 B2
A
G
A
H
PROGRAMME/TEMPERATURE SELECTOR
p
Use this control to select the desired wash programme. Turn the selector (it
can be turned in both directions) so that the programme is opposite the
reference indicator (p). The temperature selected will depend on the
programme. (See the Programme Table).
B1
SPIN SPEED SELECTOR
B2
DELAYED START KEY
C1
PRE-WASH
C2
EXTRA RINSE
C3
TIME SAVER(SUPER FAST)
G
DOOR LOCKED LAMP
H
START/PAUSE KEY
p
CONTROL POSITION INDICATOR
S
STOP/END OF CYCLE LAMP
V
TIME REMAINING LAMPS
Programme table mod HNT 6414
programme
aprox.
time
min.
programme for
max.
temp.
setting
ºC
max.
espin
speed
rpm/min
max.
load
Kg.
160
90º
1400
6
*Fast coloureds
COTTONS
Fast coloureds
&
LINENS Delicate coloureds
155
60º
1400
6
115
40º
1400
6
110
30º
1400
6
Delicate coloureds
105
1400
6
Fast coloureds
95
60º
800
2
Fast coloureds
90
50º
800
2
Delicate coloureds
85
40º
800
2
Delicate coloureds
75
30º
800
2
Delicate coloureds
70
800
2
Delicates
1,5
MIXED
SYNTHETICS
White
DELICATES
SPECIAL
60
40º
600
Woollens
55
30º
800
1
Woollens
50
800
1
Gentle rinse
25
800
Gentle spin
9
1400
Empty
4
Hand wash
Sports
50
30º
800
2
195
30º
800
2
AA 40
155
40º
1000
2
Fast 44
44
40º
800
3,5
Fast 29
29
40º
800
2
washing powder load
I
II
option keys C
* Programme as per EN 60456
Technical data mod. HNT 6414
Mains
voltage
Wash power
rating
Spin power
rating
230V./50Hz
175 W.
400 W.
Heating
Pump motor
element
Max. Power
power rating power rating
input
30 W.
1950 W.
2200 W.
Mains fuse
Amp. rating
10 A.
Water
pressure
0,05-0,8
Mpa
Water
Energy
consumption consumption
*prog.
*prog.
EN60456
EN60456
58 L.
1,02 Kw.
IMPORTANT:
- We recommend not using bleach for programs with a prewash cycle.
- Do not use liquid detergent for programs with a prewash cycle and/or timed start.
PREPARING THE WASH CYCLE
1.- Once the washing is loaded, ensure that the drum doors are properly closed..
2.- Add detergent and additives, not exceeding the maximum level indicator.
•
detergent for pre-wash I
•
detergent for wash programme II
•
bleach
•
fabric conditioner
SELECTING THE DESIRED PROGRAMMES AND OPTIONS
3.- Turn the programme selector (A) to the desired programme.
4.- Press the key or keys for any options desired (C1, C2, C3).
.- It is advisable to select the required options before pressing the Programme Start key (H).
.- Remember that if the programme has already passed the stage at which an option is
activated, that option will not be implemented.
C1 pre-wash key
This is useful for heavily soiled washing. This adds a short additional wash before the main
wash. The key can be activated only in Cottons, Mixed and Synthetics programmes. To
activate this option, always press the key before pressing the start key (H).
C2 extra rinse key
The electronic system engaged by this key activates a new special rinse cycle. More water
and a combination of drum rotation movements ensure that washing is perfectly rinsed. The
key can be activated in Cottons, Mixed, Synthetics, Delicates, Rinse, Sport and AA40
programmes.
C3 super fast key
When this key is engaged programme times are cut by as much as 50 minutes, depending on
the wash programme and temperature selected. The key can be activated only in Cottons,
Synthetics and Mixed programmes.
5.- Select spin speed if required (B1)
B1 spin selector
You can use this key to select final spin speed, but only within the range of speeds of the
programme selected. These speeds are displayed via the corresponding lamp. To cancel the
spin completely, set the speed indicator to ( ).
You can select the desired speed at any time during the programme.
6.- Once you have selected the desired options, press the START key (H). The washing
machine will start up and one of the time remaining lamps (V) will come on. This lamp
indicates approximately how much time is left before the wash programme is completed: it will
change as the programme progresses. Make sure that the stop/end of cycle lamp is flashing
before pressing the start key (H). If it remains on continuously, turn the programme selector to
OFF and re-set it to the desired programme.
To cancel an option after setting, just press the option key again (the indicator lamp will go
out).
B2 delayed start key
The washing machine can be set to start the programme selected 3, 6 or 9 hours after setting.
To do this, proceed as follows:
- Select the desired programme via the PROGRAMME SELECTOR.
- Press the key once to light up the 3 h timer lamp.
- Press the key twice to light up the 6 h timer lamp.
- Press the key 3 times to light up the 9 h timer lamp.
- Then press (H) to memorise the programme, which will start up after the time selected.
- To cancel the programme timer, press the B2 key again until the End of Cycle lamp comes
on.
Time remaining to end of cycle or programme phase display (V).
Models with this feature display the APPROXIMATE time remaining to the end of the
programme in minutes, or the current wash phase of the programme set. The programme
times may vary depending on the temperature selected, ambient temperature, mains water
pressure, the quantity and type of washing.
“Door lock” lamp (G).
The door lamp flashes when a wash programme starts, and then burns steadily. From that
moment on the door is locked (DOOR LOCK).
The DOOR LOCK lamp remains on during the whole wash cycle, thus preventing the door
from opening.
At the end of the wash cycle, the safety devices are deactivated, the light goes out and the
door can then be opened.
Cancel-change programs
Once you have started a program, and wish to change or cancel it, you should proceed in the
following manner,
- Put the program selector in the OFF position. At that instant, you have cancelled the
program and can if you wish to do so, select a new one.
- Select the new program.
- Click the key (H) again, until one of the remaining time pilot light lights up.
The washing machine will perform the new selected program.
Programme Pause
To pause the wash programme so that more washing can be added, proceed as follows:
- Hold down the start key (H) until the option key lamps begin to flash and the time remaining
lamp lights up.When the Door Lock lamp goes out (after approx. 2 minutes), open the door
and put the additional washing into the drum.
- Close the drum door and the lid properly.
- Press the start key (H), the time remaining lamp will light up and the machine will continue
with the programme.
When the programme is completed the Stop/End of cycle lamp (S) will come on and the time
remaining and Door Lock lamps (V and G) will go out.
For your own safety, set the programme selector to OFF before opening the washingmachine lid and the drum doors to remove the washing.
31.01.08/ H- 46004503 EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement